Advertisement
Advertisement
Quick Start Guide Quick Start & User Manual 1) Check kit contents Part # 508000 IP Power 9258T (USA) or Part # 508001 IP Power 9258S (Europe/Australia) User Manual/Quick Start Guide and IP Power CD Optional power cables 2) Install hardware IP Power 9258 Connect power cables. For the USA model (NEMA5-15P 100-120V outlets), the individual max output current per outlet is 6A and the total max output current for the 4 outlets is 15A. Use a power IN cable with 15A current rating and use power OUT cabless with 10A rating for each power outlet. For the European/Australian model (IEC320-C13 220-250V outlets) the individual max output current per outlet is 6A and the total max output current for the 4 outlets is 10A. Use a power IN cable with 10A current rating and use power OUT cable with 10A rating for each power outlet. Connect IP Power NETWORK port to your local 10/100 LAN 3) Set IP Power IP address The IP Power’s default network settings are: IP address: 192.168.0.50 Subnet mask: 255.255.255.0 Quick Start User Manual …… 2 …… 5 To set a new address, either: Rev: 1.1 February 16, 2007 _____________________________________________________________________________ IP POWER PAGE 1 OF 24 Connect your PC directly to the IP Power’s Ethernet (NETWORK) port and run IPEdit.exe. You first must copy the IPEdit.exe program from the IP Power CD on to your PC; or With a PC in the same subnet as the IP Power (i.e. IP address of 192.168.0.xxx), open the IP Power control web pages as detailed in the next step and select System: Setup _____________________________________________________________________________ IP POWER PAGE 2 OF 24 4) Update IP Power with your browser Enter http://192.168.0.50 (or the IP address assigned using IPEdit.exe) in the browser of your locally connected PC and login. The default username is: admin The default password is: 12345678 You can now set the password and IP address, and modify the IP Power’s other settings. 5) Control power outlets Click Set Power under Power to display the current state of each power outlet. Select On or Off and click Apply to manually control power to each outlet. Click Power Schedule under System to program when each power outlet is to be automatically powered on or off. WARNING Any changes to this equipment without permission may cause damages to your equipment! This equipment has been proven by CE & FCC to be prevented from the influence of harmful electronic jamming in normal business use conditions. IMPORTANT NOTICE 1. 2. 3. We have no responsibility for possible damage caused by improper usage or abnormal working environment Do not use IP POWER in strong vibrating condition Please contact the dealer If IP POWER works improperly Copyright © 2007 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of us. All other products mentioned in this document are trademarks of their respective manufactures. We are exempt to notify any change of our products. _____________________________________________________________________________ IP POWER PAGE 3 OF 24 _____________________________________________________________________________ IP POWER PAGE 4 OF 24 1. Introduction IP Power 9258 User Manual Table of Contents The IP power 9258 is a web browser controlled power switch that can be used easily for industrial or commercial power control. With the remote network control technology, a user connected to the local area network or Internet can query and control the power supply of attached equipment. There is no special software required, and no need to open the external case of the computer. 1. Introduction.............................................................................................. 3 2. Interface Description............................................................................... 3 3. Hardware and Software Installation....................................................... 3 4. Initial Settings .......................................................................................... 3 5. Control Using a Browser ........................................................................ 3 Setting the password for IP Power......................................................... 3 Setting the IP Power’s IP address.......................................................... 3 Email settings .......................................................................................... 3 Power control using the time schedule.................................................. 3 Default outlet settings ............................................................................. 3 Clock settings & network time protocol (NTP)....................................... 3 Wake on LAN (WOL).............................................................................. 3 6. Firmware Update .................................................................................... 3 7. DDNS Settings........................................................................................ 3 8. Direct Control Using HTTP Commands ................................................ 3 9. Frequently Asked Questions.................................................................. 3 10. Manual Control Mode ........................................................................... 3 11. Remote Browser Control Using a CM/IM4000 ................................... 3 12. Out-of-Band Access Using a CM/IM4000........................................... 3 13. Remote Serial Port Control of the IP Power........................................ 3 Maximum rated voltage for each of the 4 outlets: 250V AC, 24V DC Maximum rated current, total: 15A AC/DC (9258T), 10A AC/DC (9258S) Maximum rated current, per individual outlet: 6A AC/DC Action delay: max. 10ms Operating temperature: 0 ~ 70°C IP Power model 9258S - for EU/AU/UK for 220-250V, use power (IN) cable at 10A current. Max output current: 10A (total), 6A (individual). IP Power model 9258T - for US/TW/JP for 100-120V, use power (IN) cable at 15A current. Max output current: 15A (total), 6A (individual). 2. Interface Description IP Power 9258 front interface (from left to right): _____________________________________________________________________________ IP POWER PAGE 5 OF 24 RESET: Self-protect AC reset button. IP Power 9258 can cut off the power supply of outlets automatically if there is a short circuit or current overload. After the user resolves the problem, push the RESET button and the AC power supply will resume. LED: 4 LED indicator lights. If the LED is on, the corresponding outlet is power on. RS232 port: During normal operation, displays the power output state. If a firmware update fails, displays an IP address where the firmware update can be re-applied. Also used for secure out-of-band control with CM/IM4000 console server. RJ45 Ethernet port: Connects the IP Power to the network. _____________________________________________________________________________ IP POWER PAGE 6 OF 24 Rear interface port description (from left to right): 90-240VAC power input port Power switch: The ON/OFF power switch for the IP Power 9258 itself. Software installation OUT1 - OUT4: 4 individually switched AC outlets Once you’ve connected the power supply and network cable to the IP Power’s RJ45 network port, install the software by following the steps below: 3. Hardware and Software Installation 1. Start your computer, insert the IP Power CD, and locate the file named ipEdit.exe.. 2. Copy the file to your desktop (or another directory if you prefer). Before you start to use the IP Power 9258, please follow the steps below: 1) Check the package to make sure the contents are complete 2) Prepare an Ethernet hub or router for accessing the IP Power 9258 3) Check the voltage of the power supply to make sure it is AC 110-240 volt 4) Confirm the specifications of your power cable. (For IP Power 9258S: for 220-250V, use the 10A power cable. For IP Power 9258T: for 100-120V, use the 15A power cable.) 4. Initial Settings Hardware installation 1. Connect the IP Power to the hub using a Cat5 network cable (for remote control, you may then connect the hub or router to the Internet) 2. Connect the AC IN power adapter to the IP Power 3. Connect the power adapters of equipment to be controlled to corresponding OUT port of the IP Power 4. For 220-250V, please use power wire, which can support 10A current. Maximum output current: (total) 10A, (individual) 6A. 1. Ensure you have installed the ipEdit.exe program as described in the previous section, Software Installation. 2. Ensure that your PC is connected to the same network as the IP Power, and that the IP Power is powered on. 3. Run ipEdit.exe by double clicking the ipEdit icon. The default Ethernet address of the IP Power will be found and displayed. The default name of the IP Power is: IP 9258 4. Click IP 9258 in the left of the window and the IP Power’s name and IP address will display in the right hand fields. You can rename the IP Power or change its IP address or default gateway address. Click Update to apply the new settings. The new settings will be working in 20 seconds. For 100-120V, please use power wire which can support 15A current. Maximum output current: (total) 15A , (individual) 6A. 5. Power on your PC and the power adapter of IP Power _____________________________________________________________________________ IP POWER PAGE 7 OF 24 _____________________________________________________________________________ IP POWER PAGE 8 OF 24 5. Double click the name of the IP Power, and your browser window will open and connect to the unit automatically. Alternately, manually type the IP address of the IP Power into your browser. NOTE If you are running programs such as Microsoft Office the safe shut down may not automatically save open documents or files which may result in lost data. To allow enough time for the PC/server to safely shut down before being powered off, please set the delay time at 30 or 60 second on the IP Power control web pages Setup Delay Switch. The IP Power 9258’s default IP address is 192.168.0.50 and its subnet mask is 255.255.255.0. The IP address of your computer should be in the same subnet with that of IP Power’s (by default this subnet is 192.168.0.xxx), so that you can access the IP Power control web pages. Typically, you will want to find out the IP address of your PC and set the IP Power to reside on the same subnet. To find out the IP address of your PC: The PC/server to shut down must be on the same Ethernet network and on the same subnet as the IP Power. Select Start Run then type in cmd in the MS-DOS window, type in ipconfig Installing IP9258service.exe Insert the IP Power CD in the PC/server which is to be enabled for software shutdown Install the IP9258config.exe , by selecting the SDK button on the LHS then selecting 9258 SDK in the menu. Then double click Shutdown Program and run IP9258config.exe. On the install menu select the LHS bottom button to place the IP9258Service icon on your desktop. Click this icon then select the IP9258config.exe program 3. Fill in the fields as follows: The IP address of the PC is 192.168.100.31, so the IP Power has been set to 192.168.100.168. Both of these address are on the 192.168.100.xxx subnet. You may also change the PC’s IP address to be on the same subnet as the IP Power (by default 192.168.100.xxx), in Control Panel Network Connections Local Area Connection Properties Internet Protocol (TCP/IP) Properties. The default username and password of IP Power 9258 are: Username: admin Password: 12345678 PC or server software shutdown The IP Power 9258 can also safety shutdown a PC or server through the network before being powered off. This allows you to remotely shut down a PC/server attached to IP Power 9258 using the usual Windows safe shutdown procedure. Before using the software shutdown function, please note: 1. 2. IP9258 Address: The IP Power’s IP address HTTP Port: The port of the IP Power control web pages – this will be 80 unless you have changed it Username: admin Password: The IP Power admin password (default 12345678) Power Number: The OUT power outlet the PC/server is connected through – if many PC/servers are connected through the one power outlet and are registered with the same IP Power unit, they will all be shutdown at the same time Click Save Change, Install Service then Start Service. Restart the PC/server, then it will be enabled for software shutdown. You will need to install the IP9258service.exe program from the IP Power CD as detailed below _____________________________________________________________________________ IP POWER PAGE 9 OF 24 _____________________________________________________________________________ IP POWER PAGE 10 OF 24 Click Set Power again to refresh the status. The state of each power outlet is displayed under the Control column. System settings with browser You may set the password, IP address, e-mail address, timer setting, perform an online firmware update, and set the time of the IP Power through the IP Power control web pages. Setting the password for IP Power 5. Control Using a Browser Type the IP address of the IP Power into your web browser’s address field to access the IP Power control web pages. The username is admin and the default password is 12345678. Enter these credentials, or the password you have set. Click OK to enter the IP Power control web pages. Select Change password from the left hand menu. The default password 12345678. You may can change it to a password of your choosing (no longer than 8 characters). Click Apply to save the change. NOTE If you lose or forget the admin password, enter the username super user at the log in webpage and then click OK. Then turn the power off for a few seconds before turning the power back on. The IP Power will to be reset to using the default password of 12345678. Note: There is space between super and user. Control the power supply of the outlets Select the Set Power from the left hand menu. Setting the IP Power’s IP address Select Setup from the left hand menu. Fill in the new IP Address, Subnet Mask, Default Gateway, and DNS server address. If your network has a DHCP server automatically allocating network settings, you may choose to enable the IP Power’s DHP Client. The Beeper sound may also be enabled or disabled on this page. IP Power 9258 can control 4 outputs individually or at the same time. You can choose to power off and power on an outlet. You may also set the time to delay before performing the chosen action under Timer, by entering the time to delay in seconds and selecting On. If the IP Power is connected to your Local Area Network (LAN): You may set a fixed IP address or have it automatically assigned by a DHCP server. It is suggested that you use a fixed IP address so that it is always known. Querying the power state of the outlets _____________________________________________________________________________ IP POWER PAGE 11 OF 24 _____________________________________________________________________________ IP POWER PAGE 12 OF 24 After changing the IP Power’s IP address, type the new address in the address field of your web browser. You can also use the ipEdit.exe tool to locate the IP Power. Email settings The IP Power can be set to email its IP address 1 – 4 recipients. If the IP Power is connected to the Internet (WAN): • IP Address: Enter the IP address provided by your ISP. If IP Power is working with a router, please refer to the network settings of the router. • Subnet Mask: Enter the Subnet Mask provided by your ISP. If the IP Power is working with a router, please refer to the network settings of the router. • Default gateway: Enter the Default Gateway provided by your ISP. If the IP Power is working with a router, please refer to the network settings of the router. • DNS Server: Enter the IP address of the DNS server provided by your ISP. • DHCP Client: Automatically obtain network settings from your ISP. The IP address format is: xxx.xxx.xxx.xxx: yyyyy, where yyyyy means the port number ranging from 1 to 32767. Subnet Mask: from 0 to 254 ( xxx.xxx.xxx.0 ~ xxx.xxx.xxx.254) If DHCP is disabled, you must set the TCP port and default gateway. If DHCP is enabled, then the TCP port is preset to 80 (xxx.xxx.xxx.xxx:80) and the default gateway will be assigned by the DHCP server. If you specify a TCP port other than 80, enter it after the IP address of the IP Power when accessing the IP Power control web pages, e.g. http://xxx.xxx.xxx.xxx:yyyyy NOTE Beeper Setting: Enable – activate the beeper sounds. Disable – turn off beep sounds. When controlling the IP Power through the web pages, the beeper, if enabled, beeps once to indicate an action has been successful. Mail Server: The SMTP server for sending email. Please ensure that it is available. POP3Server: The POP3 server. Username: The SMTP username for sending email. Password: The password for Username’s account. Note: the password can be no longer than 8 characters. Sender: The same of the sender to use. This will often be username@yourdomain. Receiver 1 – 3: The email addresses to receive the IP Power’s IP address. They will receive an email containing the IP Power’s IP address each time your log in to the IP Power control web pages. Each receiver may be no more than 50 characters. Subject: The subject of the mail, no more than 50 characters. Mail Body: Type the content of the mail here, it must not be left blank. Click Save to save your settings. HTTP Command Verification specifies the HTTP authentication for the IP Power to use: o Cookie +Base64 (allows HTTP command & SDK control) o Cookie (allows HTTP command & SDK control) _____________________________________________________________________________ IP POWER PAGE 13 OF 24 _____________________________________________________________________________ IP POWER PAGE 14 OF 24 Power control using the time schedule Wake on LAN (WOL) The IP Power can be set to power on or off power outlets at specified times. Select Power Schedule from the left hand menu. Through its network port, the IP Power can send a Wake on LAN packet to a shutdown or hibernating PC on your network, causing it to power up. This facility presumes: 1. The PC’s motherboard must support the WOL function, and it must be enabled in the BIOS (typically under Power Management). The PC must be connected to the same Ethernet network as the IP Power via its network port. 2. The PC’s network card’s WOL connector must be connected to the motherboard, or the network port must be integrated into the motherboard. After setting up the motherboard and network card, use the WOL function by following two steps: Go to Network Wakeup on the IP Power control web pages Enter the MAC address (the network card’s physical address) of the PC and click Send – the PC will be powered on NOTE Each power outlet has two rows, one for the start of the schedule (e.g. powering an outlet on) and one for the end of the schedule (e.g. powering the outlet off two hours later). Additionally, the Parameter column determines how regularly the schedule should be applied: 1. To find out your network card’s MAC address: Disable Just Once Every day Work days: every Monday to Friday Weekend: every Saturday and Sunday Default outlet settings When the IP Power is powered on, each outlet will have power applied according to the default outlet settings. In the example below, all power outlets default to OFF when the IP Power is initially powered on. Right click on the network connection icon Status Support Details. The value in Physical Address is the MAC address. Clock settings & network time protocol (NTP) You may manually set the IP Power’s internal clock by specifying the year, month, day, hour, minutes and seconds. Alternately, you may choose to synchronize with an NTP server by entering its IP address and your numeric Time Zone (relative to UTC). If your network or ISP doesn’t have an NTP server, lists of public NTP servers are available on the web. _____________________________________________________________________________ IP POWER PAGE 15 OF 24 _____________________________________________________________________________ IP POWER PAGE 16 OF 24 6. Firmware Update 7. DDNS Settings Warning: If you have not been advised to update the IP Power’s firmware and do not have a new firmware file, please do not go to this page. When connecting to the Internet, the IP address you gain from ISP may be dynamically allocated, so it may change each time the Internet connection reconnects. This may result in the IP Power becoming uncontactable to remote clients, as the new address is unknown. Firmware updates are periodically released to update the functionality of the IP Power. To update the IP Power’s firmware, select Firmware Update from the left hand menu. 1) The following warning is displayed: Dynamic DNS addresses this issue by updating DNS records whenever the IP address changes. The IP Power can utilize the free service provided by DynDNS (http://www.dyndns.com) for this purpose. The IP Power will always be contactable using its DynDNS address (e.g. ippower.dyndns.org), regardless of its IP address. First, create a DynDNS account and create an account. Create a dynamic DNS host for the IP Power, e.g. ippower.dyndns.org. Warning: Do not click Update if you do not have a firmware update file. 2) Click Update, the following window is displayed: On the IP Power, select DDNS from the left hand menu. Enter the IP address and port of the DynDNS server. You can find this out on your PC by selecting Start Run then type in cmd and typing ping www.dyndns.com. Enter the number in brackets (e.g. 63.208.196.66) followed by :80 to denote the port. In Your Domain, enter the IP Power’s DynDNS address, e.g. ippower.dyndns.org. Enter the Username and Password for the DynDNS account you created. Ensure Enable DDNS is set to TRUE. Click Save. Now, each time the IP Power is powered on or Update Now is clicked, the DynDNS address will be updated to the IP Power’s current IP address. Note that the change may take several minutes to propagate to your local DNS server. 3) Click Browse and locate the firmware update file. Click Update to begin the update. Note: When the update is complete, you must wait at least one minute before you restart the IP Power. If the IP Power cannot reach the DynDNS server without going through a proxy server, select TRUE next to Proxy Enable. Enter the IP address of the proxy server in Proxy IP and the port in Proxy Port. NOTE The first time you configure DDNS, click Update Now to set the DynDNS address. NOTE Before updating the IP Power’s firmware, ensure the IP Power control web pages’ TCP port is set to 80 (this is the default), otherwise the update may fail. _____________________________________________________________________________ IP POWER PAGE 17 OF 24 _____________________________________________________________________________ IP POWER PAGE 18 OF 24 <html>P60=1,P61=0,P62=0,P63=1</html?> 8. Direct Control Using HTTP Commands Example 3: Power outlet status and control: The HTTP command: to control the 9258 operation at a specified time The IP Power provides an alternate method for directly setting and getting the status of the power outlets through HTTP commands. This is particularly useful for controlling the IP Power’s outlets using an automated script. http://username:[email protected]/Set.cmd?CMD=SetSchedule+Power =**+YY=****+MM=**+DD=**+HH=**+MN=**+SS=**+PARAM=****+ONOFF=* The format of these commands is: http://username:[email protected]/Set.cmd?CMD=command+outlet_id=1/0+outlet_id=1/0 Where: username The username you use to login to the IP Power (default is admin) password The password you use to login to the IP Power (default is 12345678) a.b.c.d The IP address of the IP Power (default is 192.168.0.50) command GetPower to read the status (specifying outlets is not required) SetPower to turn on or off the ports (power setting for each outlet must be specified after the command) port_id (SetPower only) P60 Port 1 P61 Port 2 P62 Port 3 P63 Port 4 Where: Control parameters are 1A 1B 2A 2B 3A 3B 4A 4B. A = connect power B = disconnect power YY=****+MM=**+DD=**+HH=**+MN=**+SS=* : time parameter YY: year (20YY), 01 = 2001 MM: month (0 1-12) DD: date (01-31) HH: hour (24 hours: 0- 23) MN: minute (1-60) SS: second (1-60) PARAM=*: time schedule parameter. Parameter list as follows: 128 127 31 96 Once only Every day Week days (Monday to Friday) Weekend days (Saturday and Sunday) Example 1: ONOFF=*: operate parameter 0 open 1 close The HTTP command: For example: http://admin:[email protected]. 50/Set.cmd?CMD=GetPower http:// /admin:[email protected]/Set.cmd?CMD=SetSchedule+Power=1A+YY=2006+MM=02 +DD=16+HH=06+MN=02+SS=16+PARAM=128+ONOFF=1 Returns the power status for each outlet in the following format (outlets 5 to 8 may be ignored): The above command controls the IP Power at IP address 192.168.1.0, user name is admin and password is 12345678. This 9258 will connect power of outlet 1 (p60), once only on 2006/2/16 06:02. <html>P60=0,P61=0,P62=0,P63=0,P64=0,P65=0,P66=0,P67=0</html> In the above example, all outlets are off. NOTE Example 2: The HTTP command: http://admin:[email protected]/Set.cmd?CMD=SetPower+P60=1+P61=0+P62=0+P63 =1 Turns the power on for the first (P60) and fourth (P63) outlets, and turns power off for the second (P61) and third (P62) outlets. Returns the power status for each outlet in the following format: _____________________________________________________________________________ IP POWER PAGE 19 OF 24 Use + to separate each parameter, e.g. to simply power on outlet 1: http://admin:[email protected]/Set.cmd?CMD=SetPower+P60=1 The command syntax is case sensitive so be selective using upper and lower case in command format. The free tool wget is useful for sending these HTTP commands. For example, to send the command in Example 1, you could use: _____________________________________________________________________________ IP POWER PAGE 20 OF 24 wget –O http://admin:[email protected]/Set.cmd?CMD=SetPower+P60=1+P61=0+P62 =0+P63=1 11. Remote Browser Control Using a CM/IM4000 The IP Power 9258 is a simple browser controlled power switch, without the security features needed for open public network connection or remote out-of-band control (dial-in). However when the IP Power is accessed through an IM42000 gateway or CM4000 console server, the inbuilt SSH tunneling (SDT) provides secure public access. The IM/CM4000 Management Consoles also are all preconfigured with the HTTP commands for the IP Power 9258 power strip, so power strip control is simple: 9. Frequently Asked Questions Q1: I forgot the password and can not enter the administration page now, what can I do? A1: Use the username super user when logging in to the webpage and then click OK. Turn the IP Power off for a few seconds, the turn it back on. The default username of admin and password of 12345678 will be restored. Note: there is a space between super and user. 10. Manual Control Mode Before using the manual control function it is necessary to UNPLUG / DISCONNECT all of the 4 outlets. To obtain manual control: 1) Press and hold the ON/OFF button (depicted below) for a full 5 seconds or until a sustained beep noise is heard – this enables manual control mode which can be identified by the flashing outlet lights 2) The outlet light that is not flashing is the one currently under manual control – this outlet can be turned on or off by pressing the ON/OFF button 3) To select an alternate outlet to control, press the Cycle button (labeled with a circle with arrows on it) 4) To disable manual control mode, press and hold the ON/OFF button for 5 seconds or until you can hear a sustained beep noise – signifying the deactivation of manual control mode The IM/CM4000 gateway provides out-of-band (OoB) access through a dial in modem (or through an alternate broadband connection for IM4200). To configure the IM/CM4000 for OoB dial-in access: 1. Connect a modem to the IM/CM4000 console port using a 319004 adaptor with standard UTP Cat 5 cable (the CM4001 has a DB9 console port, so it will need to use a 31900 and a 319004 adaptor) 2. Configure the IM/CM4000 gateway for OoB dial-in and set up the remote client dial-in software 3. Configure the IM/CM4000 gateway with the IP Power 9258 as a HTTP accessible Host (so it can be controlled securely with SDTConnector) 4. Configure SDTConnector so it will access the remote the IM/CM4000 gateway using dial out, then connect to the IP Power using HTTP Cycle (left): Select power outlet to manually control ON/OFF (right): Press and hold to enable/disable manual control mode, press to turn on/off the outlet selected by the cycle button _____________________________________________________________________________ IP POWER 12. Out-of-Band Access Using a CM/IM4000 PAGE 21 OF 24 _____________________________________________________________________________ IP POWER PAGE 22 OF 24 13. Remote Serial Port Control of the IP Power The IP Power is a principally a browser controlled unit, with power control effected over the LAN using HTTP commands, or a browser. The IP Power RS232 serial port mainly provides diagnostic and status information (e.g. sending out its IP address and power on messages during Power On Self Test). However the IP Power serial port also supports emergency power control, and this can be accessed using the IM/CM4000. To configure the IP Power for serial control: 1. Ensure you have the latest version of firmware for the IP Power (V1.3.8A and later) and IM/CM4000 (post V2.1.0u7) 2. Connect the IP Power 9258's CONSOLE RS232 port to the LOCAL console ports on IM/CM4000. For CM4001 and SD4002 devices this connection will use a standard UTP Cat 5 cable with a 319000 adapter at each end. For all other IM/CM4000 gateways the connection will require only one 319000 adaptor 3. Configure the IM/CM4000 gateway for OoB dial-in and set up the remote client dial-in software 4. Set up the IM/CM4000 with IP Power 9258 configured as a serially controlled power strip device 5. Configure SDTConnector so it will access the remote the IM/CM4000 gateway using dial out, then connect to the Console Manager _____________________________________________________________________________ IP POWER PAGE 23 OF 24 _____________________________________________________________________________ IP POWER PAGE 24 OF 24 ">
Advertisement