Advertisement
Advertisement
IP POWER 9258 USER MANUAL
IP POWER 9258
USER MANUAL
USER MANUAL
IP POWER 9258 USER MANUAL
IP POWER 9258T / 9258S
Version: V1.50
2008.04
- 1 - VER.
X.X,
IP POWER 9258 USER MANUAL
Warning:
Any changes to this equipment without permission may cause damages to your equipment! This equipment has been proved by CE & FCC to can be prevented from the influence of harmful electronic jamming in normal business use condition.
IMPORTANT NOTICE
1. We have no responsibility for the possible damage caused by improper usage or abnormal working environment.
2. Do not use IP POWER in strong shaking condition.
3. Please contact the dealer If IP POWER works improperly.
Copyright © 2005 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of us
All other products mentioned in this document are trademarks of their respective manufactures.
We are exempt from notify any change of our products.
- 2 -
IP POWER 9258 USER MANUAL
Table of Content
1. INTRODUCTION...........................................................................................................4
FEATURES ..........................................................................................................................
9258
FUNCTION DESCRIBE
.................................................................................................
2.SPECIFICATION............................................................................................................5
PACKAGE C ONTENTS .........................................................................................................
MINIMUM S YSTEM R EQUIREMENTS .....................................................................................
3.INTERFACE DESCRIPTION ........................................................................................6
4.HARDWARE & SOFTWARE INSTALLATION...........................................................7
HARDWARE INSTALLATION ..................................................................................................
SOFTWARE INSTALLATION ...................................................................................................
5. INITIAL SETTING .........................................................................................................8
INITIAL SETTING THROUGH ETHERNET .................................................................................
S
ETTING OF SOFTWARE SHUT DOWN CONTROLLED
PC/ S
ERVER
…………………….
6. HARDWARE CONTROL & SETTING……………………………………………….13.
7. CONTROL AND SETTING THROUTH THE INTERNET EXPLORE.................... 14
LOGIN .................................................................................................................................
CONTROL THE POWER SUPPLY OF OUTLETS ………………………………………………..
POWER SUPPLY STATE QUERY ……………………………………………………………...
SYSTEM SETTING ............................................................................................................…
SETTING THE PASSWORD …………………………………………………………….……
SETTING THE IP ADDRESS .…………………………………………………………………
EMAIL SETTINGS ……………………………………………………………………….. …
SETTING THE TIME SCHEDULE ……………………………………………………………..
S ETUP UP OWN OUTLET DEFAULT STATUS ………………….……………………………
. Internal Clock Settings & Network Time Protocol (NTP)………..……………………..
. W AKE ON L AN ………………………………………………………………………………
. GPRS
FOR
C
ELL
P
HONE
: S
UPPORT
WAP……………………………………………….
. F IRMWARE UPDATE : …………………………………………………………………….
8. DDNS SETTING ………………………… …………….………………….……………24
9. CHECK STATUS THROUGH SNMP ……………….………………….……………25
10. CONTROL AND SETTINGS THROUGH HTTP ORDER ………………………….
26
ORDER FORMAT ……………………………………………………….…………………….
11
. FAQ ……………………………………………………………….…………………….28
12. Webpage Customization ….
………………………………….…………………….28
- 3 - VER.
X.X,
IP POWER 9258 USER MANUAL
1. Introduction
IP POWER 9258 is a web controller which can be easily used in the industry field. With the remote network control technology, user can control or query the power supply of equipment.
User can do this in any computer connected to the internet or local area network, there is no special program needed, also there is no need to open the external case of the computer.
Try to imagine that while traveling in a foreign country, you can control the power supply of your electric equipments, such as a computer, a server, a router, an entrance guard or security / surveillance system directly or use a time schedule comes with the IP POWER 9258. You can remotely control the power switch with any computer connected to the network, which is not only convenient, but it also big saving on the manpower and time.
Feature
1.
Built in web server, can be used through the Ethernet or Internet network .
2.
Support multiple browser, such as Internet Explore, Netscape, you can operate the switch and check the state without any special program .
3. Control 4set AC : outlet equipment at the same time.
* 9258T - Outlet NEMA5-15P / 9258S - Outlet IEC320-C13.
4.
Supported HTTP, DDNS , SMTP, SNMP, INTERNET- fixed IP, DHCP, L AN - virtual IP
5.
Security passwords identify. Easily installed and can be updated online.
6.
Supported RS232 port communication, indicate all kinds of real time state of 9258.
7.
Separated LED indicates the state of each switch.
8.
Develop tool ( SNMP ) is provided. It can be modified to meet the user’s special need.
9. Safely designed for high voltage resistance and protection for leakage of electrical currency, using nonflammable material
10. -- can remote control to reboot the power on for the PC or Serv er at remote site ,
11.
-- can pre-set the time schedule to turn power on / off thru Internet /
Ethernet.
12. synchronize the time of 9258 to the Inte rnet web address time .
13.
WAP Mo bile Phone Control - can use the GPRS cell phone via WAP to control
14. when regain power it store each outlet to those status setting.
15.
Change the user-defined grap hics and hyperlinks to customize the web pages by webpage S DK
1 6.
Provide SDK (VB & VC) for own Software develop and application .
1
18. are each outlet ON /OFF
Specification
* Maximum rated voltage for each 4 outlet : 250V AC, 24V DC
* Maximum rated currency for eac h 4 outlet : (Total) 15A AC/DC,
* Maximum rated currency: ( Individual outlet ) 6A AC/DC
* Action delay: Max 10ms
* Working temperature: 0~ 70°C
- 4 -
IP POWER 9258 USER MANUAL
2. Specification
Package contents
* 9258S - For EU / AU / UK
* 9258T – For USA / TW / JP
Option; RJ45 (Cat5) net wire
Option : Power Cable ( Choose one)
Minimum System Requirements
Intel Pentium III 300MHz or above/compatible AMD CPU
WINDOWS operating system (IE5.0+SPI) & LINUX
Minimum 64MB RAM
VGA Card: supported direct draw
Network card with RJ45 port & Ethernet HUB or Switcher
Internet network (Ethernet, ADSL or other ways, depends on whether you need far end control ability or not)
NOTICES:
1. IP Power 9258S : for 220-250V , please use power (IN) wire at 10A current.
.
Max output current: (total) 10A. Max ( individual) 6A.
2. IP Power 9258T : for 100-120V , please use power (IN) wire at 15A current.
.
Max output current: (total) 15A. Max (individual) 6A .
- 5 - VER.
X.X,
IP POWER 9258 USER MANUAL
3. Interface Description
IP Power 9258
Front interface shown below:
From left to the right
1. RESET: self-protect AC reset button. IP Power 9258 can cut off the power supply of outlets automatically if there is a shortcut or current overload. After user having solved the problem, push the reset button, the AC power supply will become normal.
2. LED: 4 LED indicator lights. If the LED is on, means the corresponding outlet is power on.
3. RS232 port: provide the power output state and get IP address to re-update if update fail
4. Output : To connect with daughter device - IP Power 9258 Outlet
5. Circle sign and On & Off : Hardware power ON /OFF setup. Please do o refer page
11 for proper operation.
6. RJ45 Ethernet port: link to the net wire.
Rear interface shown below:
9258S: :
9258T:
Port description (from left to the right)
1. 90-240VAC power input port
2. Power switch : the power switch ON /OFF of IP Power 9258.
3. OUT 1- 4 : 4 individually switched AC outlets
- 6 -
IP POWER 9258 USER MANUAL
4. Hardware & Software installation
Before you star to use IP Power 9258, please follow the steps below
Check the package to make sure the contents is complete.
Prepare one Ethernet HUB or Router
Check the voltage of the power supply to make sure it is AC 110-240 volt
Please confirm the specification of your power cable.
IP Power 9258S : for 220-250V , please use the 1 0A power cable.
IP Power 9258T : for 100-120V , please use the 15 A power cable.
Hardware installation
1 Connect the 9258 to HUB through network wire.
2 Connect the HUB or Router to the internet (may through ADSL/XDSL modem).
3 Connect the power adapter to the 9258.
4 Connect the power adapters of under control electric equipment to corresponding out port of 9258.
Turn on your computer and the power adapter of IP Power 9258
＊ for 220-250V, please use power wire can support 10A current..
Max. output current: (total) 10A , (individual) 6A.
• for 100-120V , please use power wire can support 15A current.
.
Max. output current: (total) 15A , (individual) 6A
Software installation
Having connected the power supply and network wire with RJ45 port to the 9258, please install the software by following the steps below:
1. Start your computer, put the installation disc in the CDROM, then find the file named ipeditv3.exe in the installation disc.
2. Copy the file to your desktop or any directory you want it saved to.
3. Start the initial setting process following the construction in next section.
- 7 - VER.
X.X,
IP POWER 9258 USER MANUAL
5. Initial Settings
Initial setting through the Ethernet
.
Open “ IPEdit.exe
”. Make sure that the IP Kamera 9060-O is properly turned on and there is a Ethernet connection from the RJ45 cable.
In the local devices section of IPEdit all AVIOSYS products under the same subnet network will appear. Please refer to (Figure 1.1) below:
(Figure 1.1 IPEDIT)
- 8 -
(Figure 1.2 IPEdit)
IP POWER 9258 USER MANUAL
IPEDIT will search and display all IP Products 9XXX series under the same local Ethernet. The default name for the IP Power 9258 is “ IP9258” Please refer to (Fig. 1.2 above).
1. Double click and highlight your IP Power 9258 device. The default device name and
IP/Network settings will all be displayed on the right hand side of IPedit.
Make sure that the IP Address of your 9258 is setup on the same subnet network as your
PC’s (Subnet mask, Gateway)
* Represents that your 9258 does not match the gateway of your router .
(E.g If the Default Gateway of your computer is 192.168.1.1 The IP Address of your 9258 will need to be set up to 192.168.1.XXX.)
2a. Automatically Detect Network settings (Please go to 2b. for steps on how to manually enter network settings) a.) Click on the REF button to the right of IPEdit b.) Please wait a few seconds while IPEdit detects your network settings. Then click the Apply button to apply the new network settings
- 9 - VER.
X.X,
IP POWER 9258 USER MANUAL
2b. Manually enter network settings In Ipedit: a.) You can manually enter the networks settings for the following:
The name : (please use numbers or letter)
Gateway IP : (The default gateways IP can be found using
IP Address : (please set in the same subnet as your PC) in the text windows. b.) Then click Submit after the settings have been selected. Wait about 20 seconds for the new settings to be updated. c.) Click Rescan, and the new device settings will display in text window.
Note:
1.) Make sure the RJ45 network cable is connected and the 9258 is powered on.
2.) * The default IP address of the 9258 is 192.168.10.100
. If you cannot get into the webpage of the 9258, please make sure to set subnet of the IP Kamera 9258 to match with your PC Subnet
Mask.
To obtain the IP information manually:
In Windows Goto: a.) Start Run type in “cmd” Hit enter and the MS –DOS window will open, b.) Now type in “ipconfig”
The last set of numbers of the IP address can be any number between 1~254, but cannot be same as your PC, hub, router or any device in the network. If using in any PC, just use HUB and type the 192.168.0.100 in Browser or use “IPDdit.exe “ then you can get in the web page.
* Same SUBNET : The first 3 sections of IP address is same - XXX.XXX.XXX.abc. The part of
XXX must be the same.
(E.g. IP address is 192.168.1
.100 , then another IP address 192.168.1
.123 is the IP in same subnet.)
- 10 -
IP POWER 9258 USER MANUAL
5 .The default username and password of IP Power 9258 are:
Username: admin
Password: 12345678
Setting of software shut down controlled PC/ Server
9258 can be used to safely turn off the PC/Server through Network. With this feature you can remotely shutdown any PC/ Server which that is connected to the IP Power 9258 through normal
Windows shut down procedure. Before operating the software shutdown function it is essential to install our software:
1. Please install program “IP9258service.exe “ into the PC that will be controlled.
2. Documents created in programs like Microsoft office will not be automatically saved. The
9258 will still shutdown the controlled PC/server without saving the file.
3. You will need to reserve enough time for controlled PC/Server to shutdown after receiving a command from the 9258. Please set the delay time at 30 or 60 second in 9258 configuration webpage ( setup delay switch ) .
4. The controlled PC/Server must be in the same ETHERNET and the same SUBNET as the
9258..
Installing and Setup of the “IP9258service.exe” :
1. Insert the CD that came with the device into the PC that you want to be able to turn off.
2. Click on the icon
3. On the left hand side click on the Icon.
4. Go to the 9258 Series section and click on the Link that says Shutdown Program
- 11 - VER.
X.X,
IP POWER 9258 USER MANUAL
5. Save to your desktop and double click “ IP9258config.exe” ， to install the program:
6. Please fill correct information in each section :
* IP9258 Address : Please type in the IP address of the 9258.
* HttpPort : Fill the port of 9258, default value is 80, if amend the port in 9258 please correct.
* UserName : admin
* Password : 12345678 (password can amend in web page)
* Power Number: Please enter the power number in the 9258 that you want to control (If many
PC/Server use same power extended line, the extended line connect to channel
1 of 9258 and if all the PC / Server set as channel 1 and same IP address in
IP9258service.exe , then all the PC/Server will be controlled at same time). a.) Click on “ Save Change “. b.) Then Click “ InstallService ” c.) Then StartService ” then please shutdown the PC/Server.
After the PC has been restarted, the function will be in effect.
- 12 -
IP POWER 9258 USER MANUAL
6. Hardware Control & Settings
* This function teaches you how to use the hardware control the power on/off of the devices
NOTE:
This function is solely used for manually selecting which ports you need to be on or off. It was designed so that you can still have the ability to turn on or off certain ports in the case you do not have Ethernet connection.
Before using the H/W control function, please UNPLUG all the 4 connection or ports connected to the 9258.
Control panel as follow:
To activate Hardware control: Hold the On/Off Button for 5 seconds until you hear one beep which activates the H/W Control function. The LED lights in the front panel should continuously flash and you can hear the relay clicking when activated.
To deactivate Hardware control : Hold the On/Off Button for 5 seconds until you hear one beep which deactivates the H/W Control function.
1. Left Button (Circle button): Select power outlet 1 ~4.
2. Right Button (ON/ OFF): Turn ON/OFF each outlet.
- 13 - VER.
X.X,
IP POWER 9258 USER MANUAL
7. Control and settings through the Internet Explore)
To login to the IP Power 9258 device through Internet Explorer, type in the IP Address of your device into the address field of IE.
This will take you to the IP 9258 Login page.
Default User Name : admin
Default Password : 12345678
Once you have typed in the correct login information click okay and you can start making changes to the web server.
Control the power supply of outlets
Once you are in Web Control page of the 9258:
Click the SET POWER Link on the left side of the page. From here you can control the IO or
Power setting page (see figure below):
- 14 -
IP POWER 9258 USER MANUAL
With this page the user can control the Power On/Off of the 4 separate outlets. It also includes a timer feature that allows you to delay in seconds when you want the power to activate after you click on apply.
Power: Labels the name of the device or port that you want to control
Control: Turns on or off the device connected
Timer: Allows the user to delay in seconds the action of the device after the Apply button has been pressed.
Power Supply State Query
Click the “ Set Power” button on the left column, and the page will be refreshed. The state of each electric outlet will also be displayed in column control.
System Settings of 9258
- 15 - VER.
X.X,
IP POWER 9258 USER MANUAL
1.) Setup – System Configuration
System configuration page:
Click on the Setup link located on the left hand column. In this page the user will be able to manually enter the IP Address, Subnet Mask, Default Gateway, DNS:, DHCP Client,
Beeper, Http Command Verification, Delay Switch, and Release Version
IP address Settings : Ethernet (LAN) and Internet(WAN)
Local Area Network (LAN) :
In LAN, you can set a fixed IP address or gain it from a DHCP server automatically. We recommend you use a fixed IP address so you can access the 9258 through the internet.
Now type the new IP address in the address field of IE, you can visit the 9258. You also can use the ipedit.exe to find the IP Power 9258 and modify its IP address.
Work on Internet (WAN):
User can set the IP provided by your ISP. If the IP Power 9258 has a public IP address, you can control it through the Internet. IP Sensor 9258 supports fixed IP, DHCP.
* IP Address : Please type in the IP address provided by your ISP. If IP Power 9258.
* Subnet Mask : please type in the Subnet Mask provided by your ISP. If IP Power 9258 is working with a Router, please refer to the network settings of the Router.
* Default gateway : please type in the Default Gateway provided by your ISP. If IP Power 9258 is working with a Router, please refer to the network settings of the Router.
* DNS Server : please fill in the IP address of DNS server. If you are in Taiwan, you can set it to
168.95.1.1.
- 16 -
IP POWER 9258 USER MANUAL
* DHCP Clients : Enable– activate DHCP service. DHCP will assign IP address for each PC.
Disable – shut down the DHCP service. You can set the IP address by yourself.
* Beeper : Enable – activate the sound beeper .
Disable – turn off the sound beeper.
If you control the 9258 through the web page, the beeper will beep once when the operation works.
Reminder:
*IP address format : XXX.XXX.XXX.XXX:YYYY YYYY means the port number,
(I.E 192.168.1.100:2345)
Port ranges from: 1 to 32767
.
*Subnet Mask : Ranges from 0 to 254 (xxx.xxx.xxx.0 ~ xxx.xxx.xxx.254 )
*If DHCP is disabled , then the user must set the TCP Port and default Gateway .If
DHCP is enabled , then the TCP port will be preset to 80( xxx.xxx.xxx.xxx:80 ) and the default gateway will be set by the DHCP server.
Http Command Verification : Setup the control possibility from HTTP command or SDK (VB &
VC)
1. Select Cookie+Base64 : To enable HTTP command & SDK control
2. Select Cookie : To disable HTTP command & SDK control
2.) DDNS Settings
Please refer to page 23 for more details
3.) Setup Email
When you finished the e-mail settings, you can set to let IP Power 9258 to send its IP address automatically.
- 17 - VER.
X.X,
IP POWER 9258 USER MANUAL
For example:
* Mail Server : smtp.aviosys.com
* Port : 25
* Pop3Server : pop3.aviosys.com
* Password : ***********
* Sender : [email protected]
* Receiver 1 : [email protected]
* Receiver 2 : [email protected]
* Receiver 3 : [email protected]
* Subject: This is a sampl email
* MailBody : This is
1.) Mail Server : Outgoing Mail Server
Please make sure the server is an available mail server.
2.) Pop3Server : Incoming Mail Server. IP address ( in Internet WAN ) from your ISP for sending Internet IP address by E-mail when 9258 in Internet. To receive IP address in WAN , please fill your ISP e-mail receive server. In this part, please also set the DNS of your ISP in system configuration.
3.) Password : the password of this mailbox is no longer than 8 characters .
4.) Sender : please fill in the name of sender. The Mail Server must support SMTP and these fields must be filled in correctly.
5.) Receiver :no longer than 50 English letters. Please use blank space to separate two receiver’s e-mail address. After you have finished this setting, you will receive the email to inform you the IP address of the IP Power 9258 every time you enter the webpage.
- 18 -
IP POWER 9258 USER MANUAL
6) Subject : the subject of the mail to be no more than 50 English letters.
7) Mail Body : please type the content of the mail here, it cannot be left empty.
After you have finished all of the above settings, click “ SAVE “ and your settings will be saved.
4.) Setting the password for IP Power 9258:
Click the “ Change password “ button on the left you can enter the change password page. The default password of 9258 is 12345678.
User can change it into any password (not longer than 8 bit), then click apply button to save the change.
Note : If forget the password , Use username " super user " when log in webpage and then click "OK " turn power off for few second and then turn ON power . 9258 will to set back to default password.
( There is space between super and user. )
5.) Control the IP Power 9258 through Power Schedule :
With the power schedule the user can use this section to schedule daily events to control the devices attached to the 9258
If user wishes to control the power in one outlet of IP Power 9258, you can fill in the time in the ower control column and choose on or off.
Support parameter of operate schedule:
Disable
Just Once
Every day
- 19 - VER.
X.X,
Work Day: From Monday to Friday.
Weekend: Saturdays and Sundays
Setup up own outlet default status:
When power, each outlet will set as appointed default status.
IP POWER 9258 USER MANUAL
6.) Wake on LAN (WOL):
Remote Wake up PC by MAC address in Ethernet (LAN)
Use Network port (RJ45), you can wake PC on WAN by PC `s MAC address.
Wake On LAN (WOL) premise:
(1) First the main board needs to have Wake on Lan support. There must be a port to connect to your network card. If the motherboard supports WOL ， will need to enable this function in the
BIOS setting.
(2) Your network card must also support “WOL”, remember to connect your connect cable to
Main board or the network card cannot send the “power on” message to your motherboard.
After both the motherboard and network card have been setup, you can use WOL function by following the steps below:
Step 1: Log in 9258 web page and go to “Network Wakeup”
Step 2: Type in your MAC address then press “send” – the PC will be power ON.
Note:
1. If the Network card is not onboard card, it needs to connect with your Main board by cable.
Please refer your network card connection
2. You can get your MAC address in PC , please refer following pictures :
Go to Network sign Status Support Details
Then the value in Physical Address “ is the PC` MAC address.
- 20 -
IP POWER 9258 USER MANUAL
7.) Internal Clock Settings & Network Time Protocol (NTP):
* User can enter the internal clock settings: year, month, day, hour , minutes and second.
* NTP function: customer can synchronize the time of 9258 to the Internet web address time.
Please refer following the NTP server IP address :
* 131.246.9.116
* 139.18.25.34
* 128.176.191.9
Note: To work NTP, please do set up in e-mail and have to receive e-mail from 9258.
- 21 - VER.
X.X,
IP POWER 9258 USER MANUAL
8.) IP Service
IP Server gives the user the ability to easily search for the name of the device other than searching for a long IP number. This flexibility allows the user to easily just remember the name of their device so they can access it with ease.
To Enable IP Server: Go to IPSrv Conf on the Left hand side of the Webpage and then make sure you have IPSrv On/Off on On . The default IP server IP Address is 220.135.169.136
and provided but the user can also setup his/her own IPServer system and use their own address as well.
By setting the server address in IP server of advanced setup page, the user can easily search for his/her IP Power 9212Delux on internet just by searching for the name of the device. The default
IP address of IP server is 220.135.169.136.
Step1: Click the green “connect” button
Step2: In the device name section: Type in the name of your device (Min of 3 letters)
9.) Firmware update:
If no firmware to update please do not go to this page.
When there a new firmware to update, the user will get additional functions that is created for the
IP Power 9258. Click the firmware update on the right side of the page; and wait for a new window to pop up.
Step1: Click the “ firmware update “， you will see follow webpage :
- 22 -
IP POWER 9258 USER MANUAL
Note: Do not click “ update “ if there is no firmware file to update .
Step2 : Click update button, the following window will pop up.
Step 3: Click the Brower button to find the corresponding update file (you can download it from our web site or ask it from the dealer), then click Update button to start update firmware. When the update is finished, you must wait one minute before you restart the IP Power 9258.
NOTICE:
* Before running the online update program, please make sure that the TCP port is set to
80,or the online update may fail.
* Please check with your reseller /distributor / importer for the update news.
* If the update fail please refer chapter 10 “ Webpage Customization“
- 23 - VER.
X.X,
IP POWER 9258 USER MANUAL
8. DDNS setting
DDNS Setting
When connects to the Internet through
ADSL(PPPOE Service) , the IP address you gain from ISP is dynamic , so the visitor maybe can not visit the 9258 in local network because don’t know its IP address.
We use DDNS method to solve this problem.
Let’s explain that using the DDNS service provided by www.dyndns.com:
First, apply a domain name (for example, abcdefg) in www.dyndns.com for 9258, set the domain password and select propel
DNS server (for example, dnsdojo.net) for domain name resolve. Then input the
Domain Name Server (host name), user name, password etc in the DDNS webpage of 9258. after that, every time 9258 start or user select to submit, 9258 will send a message package including its current IP address, domain name to www.dyndns.com, then the DNS server you choose will link the domain name of 9258 to its current IP address. So , the visitor can visit the 9258 webpage by input the domain name of 9258
(abcdefg.dnsdojo.net) in the address column
in browser.
Notice: when finish setting, click SAVE button to confirm it. And click UPDATE NOW button to send DDNS message package to DDNS Server immediately.
1. DDNS IP : Please fill in the IP address of DDNS Server and port number.
2. Domain : Please fill in your total domain name in Your Domain column.
3. DDNS user : Please fill in the DDNS domain name you applied here.
4. DDNS password : Fill in the DDNS password to apply domain process in DDNS Server.
5. Enable DDNS : can select true to enable DDNS function or select false to disable it.
6. Proxy server setting : Sometimes the message package can not send to DDNS directly, you can transmit DDNS message package through proxy server. You can use the proxy server by selecting TRUE in Proxy enable column. You can find the usable IP address and port of proxy server in some BBS, or you can use some proxy server searching software to search for usable IP address and port of proxy server.
7. PROXY IP: Please fill in the IP address of proxy server here.
8. PROXY PORT : Please fill in the proxy port here.
- 24 -
IP POWER 9258 USER MANUAL
9. Check 9258 status though SNMP
9258 support SNMP V1 and V2 , user can use snmp program to get the status of each port in
9258.
- 25 - VER.
X.X,
IP POWER 9258 USER MANUAL
10. Control and Settings Through HTTP Order
User can control the 9258’s action directly though the HTTP orders.
The format of the HTTP order is: http://username:[email protected]/Set.cmd?CMD=Commnand+para1=*+pa ra2=*+para3=* ……
Explanations for the command syntax:
Username : 9258’s username, default username is admin
Password : 9258’s password, default password is 12345678
XXX.XXX.XXX.XXX
the IP Address of 9258
CMD =***Power : the function module of 9258 para1 ~ para3 parameters
Example 1 admin
: Control the power supply of 9258 using http://admin:[email protected]/Set.cmd?CMD=SetPower+
P60=1+P61=1+P62=1+P63=0
This command control IP Power 9258 IP address at
and password is
This command will:
12345678
P60 (Outlet1) = Power On
P61 (Outlet2) = Power On
P62 (Outlet3) = Power On
P63 (Outlet3) = Power Off
.
SetPower :
When this order is sent, the IP Power will return the following message:
<html>P60=1,P61=1,P62=1,P63=0</html>
192.168.1.0
, user name is
*
Function of 9258:
1. SetPower : To control I/O - read parameter as follow http://admin:[email protected]/Set.cmd?CMD=GetPower out2 － out4 same as out1
2. GetPower : Reads output 1-4 to see if the status of each output http://admin:[email protected]/Set.cmd?CMD=GetPower
Explanation for the command SetPower :
IP address (XXX.XXX.XXX.XXX
): 192.168.1.10 (IP Address of the device)
Username : admin (Username of the device)
Password : 12345678 (Password of the device)
When you use this command, 9258 you will get the following message output :
- 26 -
IP POWER 9258 USER MANUAL
<html>P60=1,P61=1,P62=1,P63=0</html>
* Schedule Control: User can use HTTP command to arrange the 9258 operation in specific time ， http command format as follow: http://username:[email protected]/Set.cmd?
CMD=SetSchedule+Power=**+YY=****+MM=**+DD=**+HH=**+MN=**+SS=**+PARAM=****
+ONOFF=*
Explanations of each part of the order for the command SetSchedulePower :
IP Address (XXX.XXX.XXX.XXX
): 192.168.1.10 (IP Address of the device)
Username : admin (Username of the device)
Password : 12345678 (Password of the device)
Control parameter are 1A 1B 2A 2B 3A 3B 4A 4B .
A means connect power . B means discount power
YY=****+MM=**+DD=**+HH=**+MN=**+SS=* : time parameter
YY : year ( 20YY ) , 01 = 2001
MM : month ( 0 1-12 )
DD : date ( 01-31)
HH : hour (24 hours : 0- 23)
MN : minute ( 1-60 )
SS : second (1-60)
PARAM=* : time schedule parameter . Parameter list as follow:
128 operate ONCE
127 EVERYDAY
31 MONDAY to FRIDAY
96 SATURDAY & SUNDAY
ONOFF=* : operate parameter
0 open
1 close
Example 1 ： control power on / off of 9258 ： http:// /admin:[email protected]/Set.cmd?
CMD=SetSchedule+Power=1A+YY=2006+MM=02+DD=16+HH=06+MN=02+SS=16+PARA
M=128+ONOFF=1
Above command control one IP Power 9258 IP address at 192.168.1.0
, user name is admin and password is 12345678 . This 9258 will connect power of outlet1 (p60) on
2006/2/16 06:02
Note ：
1. Please use + to separate each parameter ， you can only control certain power on /off as : http://admin:[email protected]/ Set.cmd?CMD=SetPower+P60=1
2. Please follow the capital and lower case in command format.
- 27 - VER.
X.X,
11. FAQ
Q1 : I forgot the password and can not enter the administration page now, what can I do?
A1 : Use username "super user" when log in webpage and then click "OK " turn power off for few second and then turn on ON . 9258 will to set back to default password.
( There is space between super and user. )
Q2 : Why the on/off operation can work immediately?
A2 : if you operate the IP Power 9258 in Ethernet, the operation will work immediately. If you operate it through the Internet, the response speed depends on the situation of the network.
12. Webpage Customization
Customer can use our Web page SDK to amend the word and background pictures for your 9258. If not familiar to write webpage, please do not do this amendment.
Important Notice:
1. Each file do not over the original file size.
1. The character word part do not over the original amount . For instance : “setup “ it is 5 characters.
2. Do not amend the structure of webpage – can only amend words and background picture.
3. Only support HTML langrage to amend the webpage.
Step 1 : Open the 9258 Webpage SDK file , and choose the webpage planned to amend. For example : web page “ipcontrol “ html file ”
- 28 -
IP POWER 9258 USER MANUAL
IP POWER 9258 USER MANUAL
Step 2 : Open amend webpage “ipcontrol “ html file :
Step 3. Amend webpage by HTML langrage( get from right click as in amend webpage”):
Step 4 :Save file format as “ UNIX ” : Like choose “DOS to UNIX
- 29 - VER.
X.X,
IP POWER 9258 USER MANUAL
Step 5. After amend the other 9258 webpage you plan to amend . Please open program
“Make9258Html “ in 9258 web page SDK and just press” make html patch”.
Step 6 . There will be a new file “ Update_2006-01-11.bin” which is the BIN file include the amend webpage. Please follow 9258 update procedure to update the firmware BIN file . Please note the
Update procedure must be done in port 80.
- 30 -
IP POWER 9258 USER MANUAL
Note: program “Make9258Html.exe “ and amend webpage must in same file.
* If update fail and can not get IP address by IP EDIT , please use RS232 jack ( DB 9 Cable) connect with the PC and 9258, and you can get IP address to log-in and update again. Please refer follow step:
1.POWER OFF the 9258
2. Use DB9 cable connect to the COM1 of PC and the RS232 of 9258
3. Execute WIN program " Hyper Terminal" : please go to " Start" --> " program"
" Accessories " --> " Communications " “Hyper Terminal” .
Set the “Bits per second” as 19200 at COM1 ( Must at COM1)
4. Then power ON 9258 you will get message in Hyper Terminal .
- 31 - VER.
X.X,
5. Please check the message and get your IP address.
IP POWER 9258 USER MANUAL
6. Use this IP address to update again. We supply original firmware V1.22 for update.
7. Log in this address to update again.
8. If still can not finish update successful, please check if create BIN file too big .
If need to ship BIN file, please use bin file V1.22.bin in SDK to update back to factory version.
- 32 -
Advertisement
