Samsung S27E450D User guide

User Manual
SE200 SE450 SE650 SERIES
The color and the appearance may differ depending on the product, and the specifications are subject to change without prior
notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than that of Samsung Electronics are owned by their respective owners.
••
An administration fee may be charged if either
‒‒ (a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
‒‒ (b) you bring the unit to a repair center and there is no defect in the product
(i.e. where you have failed to read this user manual).
••
The amount of such administration charge will be advised to you before any work or home visit is carried out.
Table of contents
Before Using the Product
Securing the Installation Space
Precautions for storage
4
4
Safety Precautions
Symbols
Cleaning
Electricity and Safety
Installation
Operation
4
5
5
5
6
7
Preparations
Parts
Frontal Buttons
Reverse Side
Right Side View (S**E450D*)
Changing Brightness, Contrast and Sharpness
settings
Changing the Volume setting
Adjusting the Product Tilt (SE200 Series)
Adjusting the Product Tilt and Height
(SE450, SE650 Series)
Rotating the Monitor (SE450, SE650 Series)
Anti-theft Lock
Installing a Wall-mount Kit or Desktop Stand
9
9
10
11
Installation
Attaching the Stand (SE200 Series)
Attaching the Stand (SE450, SE650 Series)
Removing the Stand (SE200 Series)
18
18
19
20
12
12
13
13
14
14
15
Connecting and Using a Source Device
SAMSUNG MAGIC Upscale
28
Read below before installing the monitor.
Image Size (Except S19E200BR / S19E450BR /
S19E450MR)
29
Response Time (S24E650BW)
29
H-Position & V-Position
29
Coarse
29
Fine
29
21
Connecting and Using a PC
21
Connection Using the D-SUB Cable (Analog Type) 21
Connection Using the DVI Cable
22
Connection Using the DVI-HDMI Cable
22
Connection Using the DP Cable (S**E450D*)
22
Connecting to Headphones or Speakers
(S**E450M*)
23
Connecting the Power
23
Connecting a USB device (S**E450D*)
24
Correct posture to use the product
25
Configuring Tint
Driver Installation
25
Red
30
Setting Optimum Resolution
25
Green
30
Blue
30
Color Tone
31
Gamma
31
Screen Setup
Brightness
26
Contrast
26
Sharpness
26
Resizing or Relocating the Screen
Eye Saver Mode
27
Language
32
Game Mode
27
Menu H-Position & Menu V-Position
32
SAMSUNG MAGIC Bright
27
Display Time
32
SAMSUNG MAGIC Angle (Except S19E200NY /
S22E200NY / S24E650BW)
Transparency
32
28
2
Table of contents
Setup and Reset
Specifications
Reset All
33
General
40
Smart Eco Saving
33
Standard Signal Mode Table
42
Off Timer (S19E200NW / S19E200NY /
S22E200N / S22E200NY)
33
Off Timer Plus (Except S19E200NW /
S19E200NY / S22E200N / S22E200NY)
34
PC/AV Mode (Except S19E200NW /
S19E200NY / S22E200N / S22E200NY)
34
Key Repeat Time
34
Source Detection (Except S19E200NW /
S19E200NY / S22E200N / S22E200NY)
34
INFORMATION
35
Appendix
Responsibility for the Pay Service (Cost to
Customers)
Not a product defect
A Product damage caused by customer's fault
Others
49
49
49
49
Extended warranty
50
Installing the Software
MultiScreen
36
Troubleshooting Guide
Requirements Before Contacting Samsung Customer
Service Center
37
Testing the Product
37
Checking the Resolution and Frequency
37
Check the following.
37
Q&A
39
3
Chapter 01
Before Using the Product
Securing the Installation Space
Precautions for storage
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and
damage the product. Be sure to allow the amount of space as shown below or greater when installing
the product.
――The exterior may differ depending on the product.
――Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product
(Service fee will be charged.)
Safety Precautions
10 cm (3.93 inches)
10 cm (3.93 inches)
10 cm
(3.93 inches)
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used
nearby.
10 cm
(3.93 inches)
Caution
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
10 cm (3.93 inches)
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of
this product.
10 cm (3.93 inches)
10 cm (3.93 inches)
10 cm
(3.93 inches)
This symbol alerts you that important literature concerning operation
and maintenance has been included with this product.
10 cm
(3.93 inches)
10 cm (3.93 inches)
4
Symbols
Electricity and Safety
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are
not followed.
Warning
•• Do not use a damaged power cord or plug, or a loose power socket.
•• Do not use multiple products with a single power socket.
•• Do not touch the power plug with wet hands.
Cleaning
――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
•• Insert the power plug all the way in so it is not loose.
•• Connect the power plug to a grounded power socket (type 1 insulated devices only).
――Take the following steps when cleaning.
•• Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy
object.
1 Power off the product and computer.
•• Do not place the power cord or product near heat sources.
2 Disconnect the power cord from the product.
•• Clean any dust around the pins of the power plug or the power socket with a dry cloth.
――Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric
shock may result.
3 Wipe the monitor with a clean, soft and dry cloth.
‒‒ Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
‒‒ Do not spray water or detergent directly on the product.
4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5 Connect the power cord to the product when cleaning is finished.
6 Power on the product and computer.
Caution
•• Do not disconnect the power cord while the product is being used.
•• Only use the power cord provided with your product by Samsung. Do not use the power cord with
other products.
•• Keep the power socket where the power cord is connected unobstructed.
‒‒ The power cord must be disconnected to cut off power to the product when an issue occurs.
•• Hold the plug when disconnecting the power cord from the power socket.
5
Installation
Warning
Caution
•• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
•• Do not drop the product while moving.
•• Do not install the product in poorly ventilated spaces such as a bookcase or closet.
•• Install the product at least 10 cm away from the wall to allow ventilation.
•• Keep the plastic packaging out of the reach of children.
‒‒ Children may suffocate.
•• Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
‒‒ The product may fall and become damaged and/or cause an injury.
‒‒ Using the product in an area with excess vibration may damage the product or cause a fire.
•• Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or
smoke.
•• Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
‒‒ The product lifespan may be reduced or a fire may result.
•• Do not set down the product on its front.
•• When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of
the product is not protruding.
‒‒ The product may fall and become damaged and/or cause an injury.
‒‒ Install the product only on cabinets or shelves of the right size.
•• Set down the product gently.
‒‒ Product failure or personal injury may result.
•• Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical
substances, extreme temperatures or a significant presence of moisture, or a place where
the product will operate continuously for an extended period of time) may seriously affect its
performance.
‒‒ Be sure to consult Samsung Customer Service Center if you want to install the product at such a
place.
•• Do not install the product within the reach of young children.
‒‒ The product may fall and injure children.
•• Edible oil (such as soybean oil) may damage or distort the product. Keep the product away from oil
pollution. And do not install or use the product in the kitchen or near the kitchen stove.
6
Operation
Warning
•• There is a high voltage inside the product. Never disassemble, repair or modify the product
yourself.
‒‒ Contact Samsung Customer Service Center for repairs.
•• To move the product, first disconnect all the cables from it, including the power cable.
•• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord
immediately and contact Samsung Customer Service Center.
•• Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper,
matches, etc) into the product (via the vent or input/output ports, etc).
‒‒ Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Center.
•• Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the
product.
‒‒ Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Center.
•• Do not let children hang from the product or climb on top of it.
‒‒ Children may become injured or seriously harmed.
•• If the product is dropped or the outer case is damaged, turn off the power and disconnect the
power cord. Then contact Samsung Customer Service Center.
‒‒ Continued use can result in a fire or electric shock.
•• Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
‒‒ The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a
serious injury.
•• During a lightning or thunderstorm, power off the product and remove the power cable.
•• Do not drop objects on the product or apply impact.
•• Do not move the product by pulling the power cord or any cable.
•• If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area
immediately.
•• Do not lift or move the product by pulling the power cord or any cable.
•• Do not use or keep combustible spray or an inflammable substance near the product.
•• Ensure the vents are not blocked by tablecloths or curtains.
‒‒ An increased internal temperature may cause a fire.
7
Caution
•• Leaving the screen fixed on a stationary image for an extended period of time may cause
afterimage burn-in or defective pixels.
‒‒ Activate power-saving mode or a moving-picture screen saver if you will not be using the
product for an extended period of time.
•• Disconnect the power cord from the power socket if you do not plan on using the product for an
extended period of time (vacation, etc).
‒‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
•• Use the product at the recommended resolution and frequency.
‒‒ Your eyesight may deteriorate.
•• Do not hold the product upside-down or move it by holding the stand.
‒‒ The product may fall and become damaged or cause an injury.
•• Looking at the screen too close for an extended period of time can deteriorate your eyesight.
•• Do not use humidifiers or stoves around the product.
•• Rest your eyes for more than 5 minutes or look at distance objects for every 1 hour of product use.
•• Do not touch the screen when the product has been turned on for an extended period of time as it
will become hot.
•• Store small accessories out of the reach of children.
•• Exercise caution when adjusting the product angle or stand height.
‒‒ Your hand or finger may get stuck and injured.
‒‒ Tilting the product at an excessive angle may cause the product to fall and an injury may result.
•• Do not place heavy objects on the product.
‒‒ Product failure or personal injury may result.
•• When using headphones or earphones, do not turn the volume too high.
‒‒ Having the sound too loud may damage your hearing.
8
Chapter 02
Preparations
Parts
Icons
Description
Open or close the onscreen display (OSD) menu, or return to the parent menu.
Frontal Buttons
――The color and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Key Guide
SE200 Series, S**E450B*, S**E650B*, S**E450D*
OSD control lock: Maintain the current settings, or lock the OSD control to
prevent unintended changes to settings. Enable: To lock the OSD control,
button for 10 seconds. Disable: To unlock the locked OSD
press the
control, press the
button for more than 10 seconds.
――If the OSD control is locked, Brightness and Contrast can be adjusted. Eye Saver
Mode is available. INFORMATION can be viewed.
The Eye Saver Mode function can be used by pressing the
button. (The Eye
Saver Mode is available even when the OSD control is locked.)
Press
to enable or disable Eye Saver Mode.
The items below are not available if the Eye Saver Mode function is enable.
•• PICTURE → Brightness, Game Mode, MAGICBright, MAGICAngle
SAMSUNG
S**E450M*
MENU
EYE
SAVER
SAMSUNG
•• COLOR
SOURCE
AUTO
•• SETUP&RESET → Smart ECO Saving
Move to the upper or lower menu or adjust the value for an option on the OSD
menu.
Use this button to control the brightness, contrast and sharpness of the
screen. (Except S**E450M*)
Use this button to control the brightness and contrast of the screen.
(S**E450M*)
――Volume can be adjusted if a cable is connected to the IN port. (S**E450M*)
9
Icons
Reverse Side
Description
Confirm a menu selection.
Pressing the
button when the OSD menu is not displayed will change
the input source (Analog / DVI / DisplayPort (S**E450D*)). If you power on the
button, a message
product or change the input source by pressing the
that shows the changed input source will appear at the top left corner of the
screen.
notice to improve quality.
Port
Description
Connect to a PC using a DP cable. (S**E450D*)
――This function is not available for products with an Analog interface only.
Connect to a PC using the DVI cable.
Press the
――The DVI IN terminal is supplied for the digital (DVI)-dedicated models only.
button to automatically adjust the screen settings.
――Changing the resolution in Display Properties will activate the Auto Adjustment
function.
――This function is only available in Analog mode.
Turn the screen on or off.
When a control button on the product is pressed, the Key Guide will be
displayed before the onscreen menu opens. (The guide shows the function of
the button pressed.)
Key Guide
――The color and shape of parts may differ from what is shown. Specifications are subject to change without
To access the onscreen menu when the guide is displayed, press the
corresponding button again.
The Key Guide may vary depending on the function or product model.
Refer to the actual product.
Connect to a PC using the D-SUB cable.
Connect to an audio output device such as headphones. (S**E450M*)
――Applicable to the models that have speakers only.
Connect to an audio-input source using an audio cable. (S**E450M*)
――Applicable to the models that have speakers only.
Connect the
port of the monitor and the USB port of the computer with the
USB cable. (S**E450D*)
――Applicable to the stand models that have USB ports only.
Connect to an external device.
Connect the power cord for your monitor to the POWER IN port on the back of
the product.
10
Right Side View (S**E450D*)
――The color and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Port
Description
Connect to a USB device.
――Applicable to the stand models that have USB ports only.
11
Changing Brightness, Contrast and Sharpness settings
Changing the Volume setting
Adjust the Brightness, Contrast and Sharpness setting using the
no OSD menu is displayed).
Adjust the Volume by pressing the
buttons in the initial screen (where
Sharpness
100
Brightness
button when the Key Guide is displayed.
Volume
10
Contrast
――The displayed image may differ depending on the model.
――The displayed image may differ depending on the model.
――The default brightness can vary depending on the region.
Brightness
――Applicable to the models that have speakers only.
――Volume can be adjusted if a cable is connected to the IN port.
――The functions available on the monitor may vary depending on the model. Refer to the actual product.
――This menu is not available when SAMSUNG Bright is set to Dynamic Contrast mode.
MAGIC
――This menu is not available when Smart Eco Saving is enabled.
――This menu is not available when Eye Saver Mode is enabled.
Contrast
――This menu is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when Game Mode is enabled.
Sharpness
――This menu is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when SAMSUNG Upscale is in Mode1 or Mode2 mode.
MAGIC
――This menu is not available when Game Mode is enabled.
12
Adjusting the Product Tilt (SE200 Series)
――The color and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Adjusting the Product Tilt and Height (SE450, SE650
Series)
――The color and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
-1° (-2°/+1°) ~ 20° (0°/+2°)
19" ~ 24"
27"
-3° (±2°) ~ +25° (±2°)
-4° (±2°) ~ +25° (±2°)
19"~ 22" (without a USB port)
23" ~ 27" / 21.5", 22" (with a USB port)
•• You can adjust the tilt of your monitor.
•• Hold the lower part of the product and adjust the tilt carefully.
0 (± 5 mm) 100 mm (± 5 mm)
0 (± 5 mm) 130 mm (± 5 mm)
•• To adjust the height, remove the fixing pin.
•• The monitor tilt and height can be adjusted.
•• Hold the top center of the product and adjust the height carefully.
•• The rotation and height adjustment has a certain tolerance. Stay within the tolerances when
rotating or adjusting the height of the product.
13
Rotating the Monitor (SE450, SE650 Series)
Anti-theft Lock
――The color and shape of parts may differ from what is shown. Specifications are subject to change without
――An anti-theft lock allows you to use the product securely even in public places.
――The locking device shape and locking method depend on the manufacturer. Refer to the user guide
notice to improve quality.
You can rotate your monitor as shown below.
1
2
provided with your anti-theft locking device for details.
3
To lock an anti-theft locking device:
SE200 Series
4
5
SE450, SE650 Series
6
DVI IN
RGB IN
POWER IN
1 Fix the cable of your anti-theft locking device to a heavy object such as a desk.
•• Be sure to fully extend the stand before rotating the monitor.
2 Put one end of the cable through the loop on the other end.
•• If you rotate the monitor without fully extending the stand, the corner of the monitor may hit the
floor and get damaged.
3 Insert the locking device into the anti-theft lock slot at the back of the product.
•• Do not rotate the monitor counterclockwise. The product may get damaged.
4 Lock the locking device.
‒‒ An anti-theft locking device can be purchased separately.
‒‒ Refer to the user guide provided with your anti-theft locking device for details.
‒‒ Anti-theft locking devices can be purchased at electronics retailers or online.
14
Installing a Wall-mount Kit or Desktop Stand
SE450, SE650 Series
Place a protective cloth or cushion on a flat surface. Next,
place the product with the face down on top of the cloth or
cushion.
Before Installation
――Power the product off and remove the power cable from the power socket.
SE200 Series
Place a protective cloth or cushion on a flat surface. Next,
place the product with the face down on top of the cloth or
cushion.
Hold the main body of the product with your hand as shown
by the figure.
Pull the stand in the direction of the arrow as shown in the
figure to separate it.
Unfasten the screw from the back of the product.
Lift and detach the stand.
15
Installing a Wall-mount Kit or Desktop Stand
•• Notes
‒‒ Using a screw longer than the standard length can damage the internal components of the
product.
SE200 Series
2
1
‒‒ The length of screws required for a wall mount that does not comply with the VESA standards
may vary depending on the specifications.
‒‒ Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit
or desktop stand using excessive force. The product may get damaged or fall and cause personal
injury. Samsung shall not be held liable for any damage or injury caused by using improper
screws or attaching the wall-mount kit or desktop stand using excessive force.
A
‒‒ Samsung shall not be held liable for any product damage or personal injury caused by using a
wall-mount kit other than the one specified or from an attempt to install the wall-mount kit on
your own.
3
4
‒‒ To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10
cm or farther away from the wall.
‒‒ Be sure to use a wall-mount kit that complies with the standards.
Unit: mm (inches)
B
Model name
SE200 Series
VESA screw hole specs Standard Screw
(A * B) in millimeters
100.0 x 100.0 (3.9 x 3.9)
M4
Quantity
4
――Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to
electric shock.
Attach the wall-mount kit or desktop stand here
Bracket (sold separately)
Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding
parts on the wall-mount kit or desktop stand you want to attach.
16
•• Notes
SE450, SE650 Series
‒‒ Using a screw longer than the standard length can damage the internal components of the
product.
‒‒ The length of screws required for a wall mount that does not comply with the VESA standards
may vary depending on the specifications.
‒‒ Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit
or desktop stand using excessive force. The product may get damaged or fall and cause personal
injury. Samsung shall not be held liable for any damage or injury caused by using improper
screws or attaching the wall-mount kit or desktop stand using excessive force.
‒‒ Samsung shall not be held liable for any product damage or personal injury caused by using a
wall-mount kit other than the one specified or from an attempt to install the wall-mount kit on
your own.
‒‒ To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10
cm or farther away from the wall.
B
‒‒ Be sure to use a wall-mount kit that complies with the standards.
‒‒ To install the monitor using a wall mount, disconnect the stand base from the monitor.
Unit: mm (inches)
Model name
Attach the wall-mount kit or desktop stand here
Bracket (sold separately)
Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding
parts on the wall-mount kit or desktop stand you want to attach.
SE450, SE650 Series
VESA screw hole specs Standard Screw
(A * B) in millimeters
100.0 x 100.0 (3.9 x 3.9)
M4
Quantity
4
――Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to
electric shock.
17
Installation
Attaching the Stand (SE200 Series)
――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
――The exterior may differ depending on the product.
1
Insert the Stand Connector into the Stand in the
direction shown by the figure.
2
Check if the Stand Connector is firmly connected.
3
Turn the connecting screw at the bottom of the
stand fully so that it is completely fixed.
4
Place a soft cloth over the table to protect
the product and place the product onto the
cloth so that the front of the product is facing
downwards.
5
Hold the main body of the product with your
hand as shown by the figure.
Push the assembled stand into the main body in
the direction of the arrow as shown in the figure.
- Caution
Do not hold the product upside down only by the
stand.
18
Attaching the Stand (SE450, SE650 Series)
――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
――The exterior may differ depending on the product.
――Disassembly is the reverse order of assembly.
1
Place a protective cloth or cushion on a flat
surface. Next, place the product with the face
down on top of the cloth or cushion.
5
After installing the stand, place the product
upright.
2
Do not remove the fixing pin until you are
finished attaching the stand.
3
Insert the stand base into the stand in the
direction of the arrow.
4
Fasten the screw tightly (using a screwdriver or
coin) into the bottom of the stand base.
6
You can remove the fixing pin and adjust the
stand now.
- Caution
Do not hold the product upside down only by the
stand.
19
Removing the Stand (SE200 Series)
――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
――The exterior may differ depending on the product.
1
Place a soft cloth over the table to protect the product
and place the product onto the cloth so that the front
of the product faces downwards.
3
2
While holding the stand neck with one hand, pound the
other fisted hand down onto the top of the stand base
in the direction of the arrow to detach the stand base.
4
Turn the connecting screw at the bottom of the stand
base to separate it.
Remove the stand neck from the stand base by
pulling it in the direction of the arrow as shown
in the figure.
20
Chapter 03
Connecting and Using a Source Device
Read below before installing the monitor.
Connecting and Using a PC
1 Check the shapes of both ends of the cables that came with the monitor, and check the shapes and
Select a connection method suitable for your PC.
2 Before connecting signal cables, disconnect the power cables for the monitor and external devices
――Provided ports may vary depending on the product.
3 After connecting all signal cables, connect the power cables for the monitor and external devices
Connection Using the D-SUB Cable (Analog Type)
positions of the matching ports on the monitor and external devices.
――Connecting parts may differ in different products.
from the power outlet to prevent device damage from a short circuit or overcurrent.
to the power outlet.
4 Read the user manual to familiarize yourself with the monitor functions, precautions, and proper
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
use, before using the installed monitor.
RGB IN
RGB IN
――Connect
to the RGB IN port on the product, then connect
to the RGB port on the computer.
21
Connection Using the DVI Cable
Connection Using the DVI-HDMI Cable
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
DVI IN
DVI IN
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
DVI IN
――The DVI IN terminal is supplied for the digital (DVI)-dedicated models only.
Connection Using the DP Cable (S**E450D*)
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
――Connect
to the DVI IN port on the product, then connect
to the DVI port on the computer.
――The DVI IN terminal is supplied for the digital (DVI)-dedicated models only.
DP IN
22
Connecting to Headphones or Speakers (S**E450M*)
Connecting the Power
IN
POWER IN
OUT
To use the product, connect the power cable to a power outlet and the POWER IN port on the product.
――The input voltage is switched automatically.
――Applicable to the models that have speakers only.
23
Connecting a USB device (S**E450D*)
1 Connect the
――To use
――Applicable to the stand models that have USB ports only.
――You can use a USB device such as a mouse, keyboard, memory stick or external hard disk drive (HDD) by
port of the monitor and the USB port of the computer with the USB cable.
port, you have to connect the UP (Upstream Cable) to the PC.
――Make sure to use the USB cable supplied with this monitor to connect the monitor's
port and your
computer's USB port.
connecting it directly to the
port on the monitor. You do not need to connect it to the computer.
For an external mass-storage HDD requiring external power supply, be sure to connect it to a power source.
B
USB port of the monitor supports High-Speed Certified USB 2.0.
High speed
Full speed
Low speed
Data Rate
480 Mbps
12 Mbps
1.5 Mbps
Power Consumption
2.5 W (Max., each port)
2.5 W (Max., each port)
2.5 W (Max., each port)
USB
The
B
A
A
2 Use the USB cable to connect a USB device to the
port on the monitor.
3 The use procedures are as the same as those for using an external device connecting to the PC.
•• You can connect and use a keyboard and mouse.
•• You can play a file from a media device. (Examples of media devices: MP3, digital camera, etc.)
•• You can run, move, copy or delete the files on the storage device. (Examples of storage devices:
external memory, memory card, memory reader, HDD-type MP3 player, etc.)
•• You can use other USB devices that can be connected to a computer.
――When connecting a device to the
port of the monitor, connect the device using a cable appropriate to
the device.
――For the purchase of the cable and external devices, ask the service center of the corresponding product.
――The company is not liable for problems or damages to an external device caused by using an unauthorized
cable for the connection.
――Some products do not follow the USB standard, and it may cause a malfunction of the device.
――If the device malfunctions even if it is connected to the computer, contact the service center of the device/
computer.
24
Correct posture to use the product
Driver Installation
――You can set the optimum resolution and frequency for this product by installing the corresponding drivers.
――To install the latest version of the product driver, download it from the Samsung Electronics website at
http://www.samsung.com.
Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for
the first time after purchase.
Select a language on the product and change the resolution on your PC to the optimum setting.
Use the product in the correct posture as follows:
•• Straighten your back.
――If the optimum resolution is not selected, the message will appear up to three times for a specified time
even when the product is turned off and on again.
――The optimum resolution can also be selected in Control Panel on your PC.
•• Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at
the screen.
•• Keep your eyes directly in front of the screen.
•• Adjust the angle so light does not reflect on the screen.
•• Keep your forearms perpendicular to your upper arms and level with the back of your hands.
•• Keep your elbows at about a right angle.
•• Adjust the height of the product so you can keep your knees bent at 90 degrees or more, your heels
attached to the floor, and your arms lower than your heart.
•• Do the Eye excercises or blink frequently,then eye fatigue will be relieved.
25
Chapter 04
Screen Setup
Configure the screen settings such as brightness.
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
Contrast
Adjust the contrast between the objects and background. (Range: 0~100)
Brightness
A higher value will increase the contrast to make the object appear clearer.
――This option is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
MAGIC
You can adjust the general brightness of the picture. (Range: 0~100)
――This menu is not available when Game Mode is enabled.
A higher value will make the picture appear brighter.
――This menu is not available when SAMSUNG Bright is set to Dynamic Contrast mode.
MAGIC
――This menu is not available when Smart Eco Saving is enabled.
Sharpness
――This menu is not available when Eye Saver Mode is enabled.
Make the outline of objects more clear or blurry. (Range: 0~100)
A higher value will make the outline of objects clearer.
――This option is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when SAMSUNG Upscale is in Mode1 or Mode2 mode.
MAGIC
――This menu is not available when Game Mode is enabled.
26
Eye Saver Mode
SAMSUNG MAGIC Bright
Set to an optimum picture quality suitable for eye relaxation.
This menu provides an optimum picture quality suitable for the environment where the product will be
used.
TÜV Rheinland “Low Blue Light Content” is a certification for products which meet requirements for
lower blue light levels. When Eye Saver Mode is 'On', the blue light that wavelength is around 400nm
will decrease, and it will provide an optimum picture quality suitable for eye relaxation. At the same
time, the blue light level is lower than in the default settings, and it was tested by TÜV Rheinland and
certified as it met the requirements of TÜV Rheinland “Low Blue Light Content” standards.
――This menu is not available when Smart Eco Saving is enabled.
――This menu is not available when Game Mode is enabled.
――This menu is not available when Eye Saver Mode is enabled.
――This menu is not available when SAMSUNGAngle is enabled.
MAGIC
You can customize the brightness to suit your preferences.
Game Mode
•• Custom: Customize the contrast and brightness as required.
Configure the product screen settings for game mode.
•• Standard: Obtain a picture quality suitable for editing documents or using Internet.
Use this feature when playing games on a PC or when a game console such as PlayStation™ or Xbox™
is connected.
――This menu is not available when Eye Saver Mode or Smart Eco Saving is enabled.
•• Web mode: Obtain the best screen for editing documents and browsing the Internet without the
issue of narrow viewing angles. (S19E200NY, S22E200NY)
•• Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content.
•• Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment.
――When the monitor turns off, enters power-saving mode or changes input sources, Game Mode turns Off
even if it is set to On.
――If you want to keep Game Mode enabled all the time, select Always On.
27
SAMSUNG MAGIC Angle (Except S19E200NY /
S22E200NY / S24E650BW)
MAGICAngle
allows you to configure the settings to obtain the optimum picture quality according to
your viewing angle.
SAMSUNG
――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode.
MAGIC
SAMSUNG MAGIC Upscale
MAGICUpscale function
SAMSUNG
can enhance the layers of the picture details and the vividness of the picture.
The function has more obvious effects on low-resolution pictures.
――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when Game Mode is enabled.
•• Off / Mode1 / Mode2
――This menu is not available when Game Mode or Eye Saver Mode is enabled.
――Comparing with Mode1, Mode2 has a stronger effect.
You can customize the angle to suit your preferences.
4
1
1
5
5
2
3
•• Off
1
: Select this option to view directly in front of the product.
•• Lean Back Mode 1
2
: Select this option to view from a place slightly lower than the product.
•• Lean Back Mode 2
3
: Select this option to view from a place lower than Lean Back Mode 1.
•• Standing Mode
•• Side Mode
5
4
: Select this option to view from a place higher than the product.
: Select this option to view from either side of the product.
•• Group View: Select this option for more than one viewer to view from places
1
,
4
, and
5
.
•• Custom: Lean Back Mode 1 will be applied by default if Custom is selected.
28
Image Size (Except S19E200BR / S19E450BR /
S19E450MR)
Change the picture size.
In PC mode
•• Auto: Display the picture according to the aspect ratio of the input source.
Response Time (S24E650BW)
Accelerate the panel response rate to make video appear more vivid and natural.
――It is best to set Response Time to Standard or Faster when you are not viewing a movie.
H-Position & V-Position
•• Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
H-Position: Move the screen to the left or right.
In AV mode
V-Position: Move the screen up or down.
•• 4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
――This menu is available in Analog mode only.
•• 16:9: Display the picture with an aspect ratio of 16:9.
•• Screen Fit: Display the picture with the original aspect ratio without cutting off.
•• Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
(S19E200NW, S19E200BW, S22E200BW, S19E450BW, S19E450MW, S22E450BW, S22E450MW,
S22E450DW)
――The function may not be supported depending on the ports provided with the product.
――This menu is only available when Image Size is set to Screen Fit in AV Mode.
When a 480P or 576P or 720P or 1080P signal is input in AV mode and the monitor can display normally,
select Screen Fit to adjust horizontal position in 0-6 levels.
Coarse
――Changing the screen size is available when the following conditions are satisfied.
――A digital output device is connected using the DVI/DP cable.
――The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally (Not every model can
support all of these signals.).
――This can only be set when the external input is connected through DVI/DP and PC/AV Mode is set to AV.
Adjust the screen frequency.
――This menu is available in Analog mode only.
Fine
Fine-adjust the screen to obtain a vivid picture.
――This menu is available in Analog mode only.
29
Chapter 05
Configuring Tint
A detailed description of each function is provided. Refer to your product for details.
SAMSUNG
Bright is in Cinema or Web mode, Dynamic Contrast mode. This menu is not available when Game Mode or Eye Saver Mode is enabled.
Adjust the tint of the screen. This menu is not available when MAGIC
――The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
Green
Adjust the value of the color green in the picture. (Range: 0~100)
Red
A higher value will increase the intensity of the color.
Adjust the value of the color red in the picture. (Range: 0~100)
Blue
A higher value will increase the intensity of the color.
Adjust the value of the color blue in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
30
Color Tone
Adjust the general color tone of the picture.
――This menu is not available when SAMSUNGAngle is enabled.
MAGIC
•• Cool 2: Set the color temperature to be cooler than Cool 1.
•• Cool 1: Set the color temperature to be cooler than Normal mode.
•• Normal: Display the standard color tone.
•• Warm 1: Set the color temperature to be warmer than Normal mode.
•• Warm 2: Set the color temperature to be warmer than Warm 1.
•• Custom: Customize the color tone.
Gamma
Adjust the mid-range brightness (Gamma) for the picture.
――This menu is not available when SAMSUNGAngle is enabled.
MAGIC
•• Mode1 / Mode2 / Mode3
31
Chapter 06
Resizing or Relocating the Screen
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
Menu H-Position & Menu V-Position
Menu H-Position: Move the menu position to the left or right.
Language
Menu V-Position: Move the menu position up or down.
Set the menu language.
Display Time
――A change to the language setting will only be applied to the onscreen menu display.
――It will not be applied to other functions on your PC.
Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified
period of time.
Display Time can be used to specify the time after which you want the OSD menu to disappear.
Transparency
Set the transparency for the menu windows.
32
Chapter 07
Setup and Reset
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
Reset All
Return all the settings for the product to the default factory settings.
Smart Eco Saving
The Smart Eco Saving function reduces power consumption by controlling the electric current used by
the monitor panel.
――This menu is not available when Eye Saver Mode is enabled.
――Game Mode will automatically turn off when Smart Eco Saving is enabled.
――Dynamic Contrast mode is not available when Smart Eco Saving is enabled.
•• Off: Deactivate the Smart Eco Saving function.
•• On: The power consumption will automatically be reduced by about 10% over the current setting.
(The reduction of power consumption depends on the customer screen brightness condition.)
Off Timer (S19E200NW / S19E200NY /
S22E200N / S22E200NY)
Configuring Off Timer
Off Timer: Turn on Off Timer mode.
Turn Off After: The off timer can be set within a range of 1 to 23 hours. The product will automatically
power off after the specified number of hours.
――This option is only available when Off Timer is set to On.
――For products for the market in some regions, the Off Timer is set to automatically activate 4 hours after the
product powers on. This is done in accordance with power supply regulations. If you do not want the timer
to activate, go to MENU → SETUP&RESET and set Off Timer to Off.
33
Off Timer Plus (Except S19E200NW /
S19E200NY / S22E200N / S22E200NY)
Configuring Off Timer
Off Timer: Turn on Off Timer mode.
Turn Off After: The off timer can be set within a range of 1 to 23 hours. The product will automatically
power off after the specified number of hours.
――This option is only available when Off Timer is set to On.
――For products for the market in some regions, the Off Timer is set to automatically activate 4 hours after the
product powers on. This is done in accordance with power supply regulations. If you do not want the timer
to activate, go to MENU → SETUP&RESET → Off Timer Plus and set Off Timer to Off.
Configuring Eco Timer
Eco Timer: Turn on Eco Timer mode.
Eco Off After: The Eco Timer can be set between 10 and 180 minutes. The product will automatically
power off after the specified time has elapsed.
――This option is only available when Eco Timer is set to On.
――This menu is not available for S19E200NY, S19E200NW, S22E200NY and S22E200N models.
PC/AV Mode (Except S19E200NW /
S19E200NY / S22E200N / S22E200NY)
Set PC/AV Mode to AV. The picture size will be enlarged.
This option is useful when you view a movie.
•• Set to PC when connected to a PC.
•• Set to AV when connected to an AV device.
――This function does not support Analog mode.
――Supplied for the wide models only such as 16:9 or 16:10.
――If the monitor (when set to DVI/DP) is in power saving mode or is displaying the message Check Signal
Cable, press the
button to display the On Screen Display (OSD). You can select PC or AV.
Key Repeat Time
Control the response rate of a button when the button is pressed.
Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once
when a button is pressed.
Source Detection (Except S19E200NW /
S19E200NY / S22E200N / S22E200NY)
Select either Auto or Manual as the method to recognize input signal.
34
INFORMATION
View the current input source, frequency and resolution.
PICTURE
COLOR
MENU SETTINGS
SETUP&RESET
INFORMATION
INFORMATION
LS********/**
S / N : ***************
Analog
**kHz **Hz **
****x****
Optimal Mode
****x**** **Hz
――The displayed image may differ depending on the model.
35
Chapter 08
Installing the Software
MultiScreen
System Requirements
OS
Hardware
•• Windows™ 2000
•• At least 32MB of memory
•• Windows XP Home Edition
•• At least 60MB of free space on the hard disk drive
•• Windows XP Professional
MultiScreen enables users to use the monitor by partitioning multiple sections.
――The software may not work properly if you do not restart the computer after the installation.
――The MultiScreen icon may not appear depending on the computer system and the product specifications.
――If the shortcut icon does not appear, press the F5 key.
Restrictions and Problems with the Installation
•• Windows Vista 32Bit
•• Windows 7 32Bit
•• Windows 8 32Bit
•• Windows 10 32Bit
――For MultiScreen, the operating systems Windows 2000 or later is recommended.
The MultiScreen installation may be affected by the Graphics Card, Motherboard and the Networking
Environment.
36
Chapter 09
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Center
――Before calling Samsung Customer Service Center, test your product as follows. If the problem persists,
contact Samsung Customer Service Center.
Check the following.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connectors are locked.
Testing the Product
Check if your product is operating normally by using the product test function.
Screen issue
If the screen is turned off and the power indicator blinks even though the product is properly connected
to a PC, perform a self-diagnosis test.
The power LED is off. The screen will not switch on.
1 Power off both the PC and product.
Check that the power cable is connected properly.
2 Disconnect the cables from the product.
The message Check Signal Cable appears.
3 Power on the product.
Check that the cable is properly connected to the product.
4 If the message Check Signal Cable appears, the product is working normally.
Check that the device connected to the product is powered on.
――If the screen remains blank, check the PC system, video controller and cable.
Not Optimum Mode is displayed.
Checking the Resolution and Frequency
For a mode that exceeds the supported resolution(refer to Standard Signal Mode Table), the message
Not Optimum Mode will appear for a short time.
――The displayed resolution may vary, depending on the computer system settings and cables.
This message appears when the signal from the graphics card exceeds the maximum resolution or
frequency for the product.
Change the maximum resolution and frequency to suit the product performance, referring to
Standard Signal Mode Table (P.42).
The images on the screen look distorted.
Check the cable connection to the product.
37
The screen is not clear. The screen is blurry.
Sound issue
Adjust Coarse and Fine.
Remove any accessories (video extension cable, etc.) and try again.
There is no sound.
Set the resolution and frequency to the recommended level.
Check the connection of the audio cable or adjust the volume.
The screen appears unstable and shaky. There are shadows or ghost images left on the screen.
Check that the resolution and frequency for the PC are within the range of resolution and frequency
compatible with the product. Next, if required, change the settings, referring to Standard Signal
Mode Table (P.42) in this manual and the INFORMATION menu on the product.
The screen is too bright. The screen is too dark.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound
card or software program.
Adjust Brightness and Contrast.
Screen color is inconsistent.
Source device issue
Change the COLOR settings.
The colors on the screen have a shadow and are distorted.
Change the COLOR settings.
White does not really look white.
Change the COLOR settings.
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
――The LED lights on the frame of the product may be seen depending on the user's viewing angle. The light is
harmless to people and has no bearing on product features and performance. The product is safe to use.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
The product is operating in power-saving mode.
Press any key on the keyboard or move the mouse to return to normal operating mode.
38
Q&A
――Refer to the user manual for your PC or graphics card for further instructions on adjustment.
How can I change the frequency?
Set the frequency on your graphics card.
•• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor, and adjust Refresh rate under Monitor settings.
•• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor, and adjust Refresh rate under Monitor settings.
•• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalization → Display Settings → Advanced Settings → Monitor, and adjust Refresh rate under Monitor settings.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Refresh rate under Monitor settings.
•• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Refresh rate under Monitor settings.
•• Windows 10: Go to Settings → System → Display → Advanced display settings → Display adapter properties → Monitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution?
•• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings, and adjust the resolution.
•• Windows ME/2000: Go to Control Panel → Display → Settings, and adjust the resolution.
•• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize → Display Settings, and adjust the resolution.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust Resolution, and adjust the resolution.
•• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust Resolution, and adjust the resolution.
•• Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust the resolution.
How do I set power-saving mode?
•• Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows Vista: Set power-saving mode in Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows 8(Windows 8.1): Set power-saving mode in Settings → Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen timeout settings → Power & sleep or BIOS SETUP on the PC.
39
Chapter 10
Specifications
General
Model Name
S19E200NY
S19E200NW / S19E200BW / S19E450BW /
S19E450MW
S19E200BR / S19E450BR / S19E450MR
S22E200NY / S22E200B / S22E200N /
S22E450B / S22E450M / S22E450D
Size
19 CLASS (18.5 inches / 47.0 cm)
19 CLASS (19.0 inches / 48.1 cm)
19 CLASS (19.0 inches / 48.2 cm)
22 CLASS (21.5 inches / 54.6 cm)
Display area
409.8 mm (H) x 230.4 mm (V)
408.24 mm (H) x 255.15 mm (V)
376.32 mm (H) x 301.06 mm (V)
476.64 mm (H) x 268.11 mm (V)
16.1 Inches (H) x 9.1 Inches (V)
16.1 Inches (H) x 10.0 Inches (V)
14.8 Inches (H) x 11.9 Inches (V)
18.8 Inches (H) x 10.6 Inches (V)
0.300 mm (H) x 0.300 mm (V)
0.2835 mm (H) x 0.2835 mm (V)
0.294 mm (H) x 0.294 mm (V)
0.24825 mm (H) x 0.24825 mm (V)
0.011811 Inches (H) x 0.011811 Inches (V)
0.011161 Inches (H) x 0.011161 Inches (V)
0.011575 Inches (H) x 0.011575 Inches (V)
0.009774 Inches (H) x 0.009774 Inches (V)
Pixel Pitch
Model Name
S22E200BW / S22E450BW / S22E450MW /
S22E450DW
S23E200B / S23E450B
S24E200BL / S24E450BL / S24E450DL
S24E450B / S24E450M / S24E450D
Size
22 CLASS (22.0 inches / 55.8 cm)
23 CLASS (23.0 inches / 58.4 cm)
24 CLASS (23.6 inches / 59.8 cm)
24 CLASS (24.0 inches / 60.9 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
509.76 mm (H) x 286.74 mm (V)
521.28 mm (H) x 293.22 mm (V)
531.36 mm (H) x 298.89 mm (V)
18.7 Inches (H) x 11.7 Inches (V)
20.1 Inches (H) x 11.3 Inches (V)
20.5 Inches (H) x 11.5 Inches (V)
20.9 Inches (H) x 11.8 Inches (V)
0.282 mm (H) x 0.282 mm (V)
0.2655 mm (H) x 0.2655 mm (V)
0.2715 mm (H) x 0.2715 mm (V)
0.27675 mm (H) x 0.27675 mm (V)
0.011102 Inches (H) x 0.011102 Inches (V)
0.010453 Inches (H) x 0.010453 Inches (V)
0.010689 Inches (H) x 0.010689 Inches (V)
0.010896 Inches (H) x 0.010896 Inches (V)
Pixel Pitch
40
Model Name
S24E650BW
S27E450B / S27E450D
Size
24 CLASS (24.0 inches / 61.1 cm)
27 CLASS (27.0 inches / 68.5 cm)
Display area
518.4 mm (H) x 324.0 mm (V)
597.6 mm (H) x 336.15 mm (V)
20.4 Inches (H) x 12.8 Inches (V)
23.5 Inches (H) x 13.2 Inches (V)
0.270 mm (H) x 0.270 mm (V)
0.3114 mm (H) x 0.3114 mm (V)
0.01063 Inches (H) x 0.01063 Inches (V)
0.01226 Inches (H) x 0.01226 Inches (V)
Pixel Pitch
Power Supply
This product uses 100 to 240 V.
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Environmental
conditions
Operating
Temperature: 50 °F – 104 °F (10 °C – 40 °C)
Humidity: 10% – 80%, non-condensing
Storage
Temperature: -4 °F – 113 °F (-20 °C – 45 °C)
Humidity: 5% – 95%, non-condensing
――Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes place automatically.
However, you can customize the installation settings if desired.
――Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the LCD panel. This does not affect product performance.
――The above specifications are subject to change without notice to improve quality.
――This device is a Class B digital apparatus.
――For detailed device specifications, visit the Samsung Electronics website.
(USA only)
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website:
www.samsung.com/recyclingdirect or call, (877) 278 - 0799
41
Standard Signal Mode Table
Model Name
Synchronization
Resolution
Optimum Resolution
Maximum Resolution
1366 x 768 @ 60 Hz
1366 x 768 @ 60 Hz
S19E200NW / S19E200BW / S19E450BW / S19E450MW
1440 x 900 @ 60 Hz
1440 x 900 @ 75 Hz
S19E200BR / S19E450BR / S19E450MR
1280 x 1024 @ 60 Hz
1280 x 1024 @ 75 Hz
S22E200BW / S22E450BW / S22E450MW / S22E450DW
1680 x 1050 @ 60 Hz
1680 x 1050 @ 60 Hz
S22E200B / S23E200B / S24E200BL / S22E200NY / S22E200N /
S22E450B / S22E450M / S22E450D / S23E450B / S24E450BL /
S24E450DL
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
S19E200NY
Horizontal Frequency
Vertical Frequency
30 – 81 kHz
56 – 75 Hz
S24E650BW
56 – 60 Hz
1920 x 1200 @ 60 Hz
1920 x 1200 @ 60 Hz
S24E450B / S24E450M / S24E450D / S27E450B / S27E450D
56 – 75 Hz
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal
modes, the screen may be blank even though the power LED turns on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
42
S19E200NY
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
43
S19E200NW / S19E200BW / S19E450BW / S19E450MW
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
44
S19E200BR / S19E450BR / S19E450MR
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
45
S22E200NY / S22E200N / S22E200B / S23E200B / S24E200BL / S22E450B / S22E450M / S22E450D / S23E450B / S24E450BL / S24E450DL / S24E450B / S24E450M / S24E450D / S27E450B / S27E450D
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
46
S22E200BW / S22E450BW / S22E450MW / S22E450DW
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
47
S24E650BW
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
VESA, 1920 x 1200
74.038
59.950
154.000
+/-
――Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in
kHz.
――Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
――This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality.
To avoid this, it is recommended that you select the optimum resolution specified for your product.
――Check the frequency when you exchange a CDT monitor (connected to a PC) for an LCD monitor. If the LCD monitor does not support 85 Hz, change the vertical frequency to 60 Hz using the CDT monitor before you exchange it
with the LCD monitor.
48
Chapter 11
Appendix
Responsibility for the Pay Service (Cost to
Customers)
A Product damage caused by customer's fault
――When the service is requested, in spite of in warranty, we may charge you for a visit from a service
•• External impact or drop.
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• Use of supplies or separately sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorised electrical connections.
•• Not following the "cautions" in User Manual.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•• If a product is reinstalled or devices are connected additionally after installing the purchased
product for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If customer requests instructions on how to use because of another company's product.
•• If customer requests instructions on how to use the network or another company's Program.
•• If customer requests software installation and setup for the product.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator,
Lamp, Filter, Ribbon, etc.)
――If customer requests a service in case the product has no defect, service fee may be charged. So please
read User Manual first.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through homeshopping or online.
49
Extended warranty
You can buy an extended warranty within 90 days of purchasing the product.
The extended warranty will cover an additional period of 3 years, beyond the standard 3 year warranty.
Samsung guarantee that replacement parts will be available for 5 years after the end of production.
After 5 years, in the event that the Samsung’s service center has run out of replacement parts and
cannot repair the product, Samsung will replace your product at no additional charge. If the model you
purchased is no longer available, Samsung replace it with the current equivalent model.
50