advertisement
▼
Scroll to page 2
of 60
Please read this operating owner 's manual carefully before the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached and on quote this information require the back of the Monitor to your dealer when you service. Model number Serial number : : PLASMONITR MT-60PZ11/B/G/K/S MT-60PZ12/A/B/K/S MZ-60PZ13/B/G/K/S MT-60PZ14/A/B/K/S MZ-60PZ14/A/B/K/S OWNER'S MANUAL INPUT ON/OFF SELECT VOLUME What is Plasma a Display ? If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance. At this moment, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° Wide - angle range A Plasma Display provides tortion from any direction. Easy of vision more than 160° Plasma Big range of vision so that you can get a picture without dis- installation A Plasma The angle Display is much lighter and Display at the desired place. smaller than other same class products so that you can install the screen screen of a Plasma Multimedia Plasma Display is 60" so explanation can get vivid experience as if you are in a theater. Display A Plasma Display can be connected with game, internet and so on. The that you a computer so that you about coloured dots may be can use present on it as a screen PDP for conference, screen The PDP which is the display device of this product is composed of 0.9 to 2.2 million cells and a few cell defects can occur in the manufacture of the PDP. Several coloured dots visible on the screen would be acceptable, in line with other PDP manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product which corresponds to this standard is regarded as acceptable. It means that it could not be changed or refunded. We promise that we'll do our best to develop our technology to minimize the cell defects. The In the explanation about noise of 60" PDP way that a fan is used in a PC to keep the CPU cool, the PDP is equipped with cooling fans to the reliability of this product. Therefore, a certain level of noise could occur when the fan is operated. This noise doesn't have any negative effect on its efficiency and liability and it's also determined to have no difficulty while using this product. The noise from the fans is normal in the operation of this product. We hope you will understand that a certain level of noise is acceptable. It means that it is not changeable nor refundable. same improve WARNING MT/Z-60PZ11/13 series is Class A product. In a domestic environment this product may radio interference in which case the user may be required to take adequate measures. cause WARNING MT/Z-60PZ12/14 series is Class B product. In a domestic environment this product may radio interference in which case the user may be required to take adequate measures. cause WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. INPUT ONOFF SELECT VOLUME Contents First step Instructions ....................................................4 Safety Monitor Overview Controls of the Monitor .............................................8 Controls of the remote control ................................12 Monitor Installation .................................................14 Equipment Connections and Setup Watching VCR ........................................................16 Watching Cable TV.................................................17 Watching external AV source..................................18 Watching DVD ........................................................19 Connecting PC .......................................................20 Function checking in PC mode ..............................22 Adjusting in PC mode .............................................23 PIP function ............................................................26 Twin picture mode ..................................................29 Using the remote control ........................................31 Basic Features Setup and Operation Turning on the Monitor ...........................................32 Selecting the on screen language ..........................33 Function checking...................................................34 Sleep Timer Setting Sleep Timer (Monitor turn-off time) ............35 Picture & Sound Auto picture control ................................................36 Adjusting picture condition .....................................37 DRP (Digital Reality Picture) ..................................38 Selecting menu options ..........................................39 Adjusting Sound: Bass, Treble, Balance ................40 Auto sound control .................................................41 AVL (Auto volume leveler) ......................................42 Special Features Using Still function ..................................................43 Adjusting OSD Transparency .................................44 Adjusting colour temperature (option) ....................45 Setting picture format .............................................46 External control device setup .................................47 Others Troubleshooting check list ......................................58 Product specifications.............................................59 Safety - Instructions It is recommended that this product only be used at an altitude of less than 6562 feet (2000m) to get the best quality picture and sound. WARNING Indorstali WARNIN Do not place the Monitor in direct sunlight or near heat sources such as heat registers, stove and so on. This may - cause a This plasma be mounted display is designed horizontally (wide to viewing). fire. WARNING Do not the Monitor in such as a bathany place where it use damp place room or OutdorInsali is likely to get wet. Bend antenna cable between inside and outside building to prevent rain from flowing in. - This may cause a fire or could give an electric shock. - WARNING WARNING Earth wire should be connected. - - Power - If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage. If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician. Do not connect ground to telephone wires, lightning rods or gas pipe. Short-circuit breaker 4 This may cause water damaged inside the Monitor and could give an electric shock. Never touch the power with a wet hand - This may cause an plug electric shock. * Safety instructions have two kinds of information, and each meaning of it is below. as WARNING The violation of this instruction may cause serious WARNIN The violation of this instruction may cause injuries light injuries or and even death. of the damage product. W Take care of danger that may happen under specific condition. WARNIN Disconnect from the mains and remove all connections before moving. Do not place the Monitor in built-in installation such as a bookcase or rack. a - Ventilation required. When installing table, be careful edge - the Monitor not to of its stand. on a place the This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor. WARNING Do not place an outside antenna in the vicinity of overhead power lines other electric light or power circuits. - This may cause an electric shock. or There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. - This may cause an electric shock. WARNING Do not pull the cord but the when unplugging. plug - This may cause a fire. Ensure the power cord doesn't trail across any hot objects like a heater. - This may cause tric shock. a fire or an elec- Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose. - This may cause a fire an electric shock. or FirstepMonvwCcBaSlmPu&df Others 5 Safety Instructions WARNING WARNING Do not placing anything containing liquid on - Using top of the Monitor. This may cause a fire could give an electric shock. or Do not insert any into the exhaust vent. Do not object - place heavy objects on the Monitor. This may cause a fire could give an electric shock. or - This may injury to a cause child serious adult. or WARNING Do not use water the Monitor while cleaning. - Cleanig This may cause damaged the Monitor or could give an electric shock. In case of smoke or strange smell from the Monitor, switch it off ,unplug it from the wall outlet and contact your dealer or service center. - This may cause a fire an electric shock. or could give WARNING Do not attempt to service the Monitor yourself. Contact your dealer or service center. Others 6 - This may cause damaged the Monitor or could give an electric shock. During unplug a lightning thunder, the Monitor from the wall outlet and don't touch an antenna cable. - This may cause Monitor or could electric shock. damaged give an the WARNING * in U.K. only This set is supplied with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is not suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted. A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or with the earth symbol or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse, either in the plug, or at the distribution board. The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. WARNIN WARNING Dispose of used batteries carefully to protect a child from eating them. - In case to see a When moving the Monitor assembled with speakers do not carry holding the speak- Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen. ers. that it eats them, take it doctor immediately. - This may cause the Monitor to fall, causing serious injury child or adult, and to a serious damage to the Monitor. WARNING Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. - This may cause damaged the Monitor an electric shock. or could Contact the service center once a year to clean the internal part of the Monitor. - Accumulated dust can cause mechanical failure. give WARNING The distance between eyes and the screen should be about5~7timesaslongas diagonal length of the Unplug the Monitor from the wall outlet when it is left unattended and unused for long periods of time. screen. - - If not, eyes will strain. Accumulated dust may cause fire or an electric shock from deterioration or electric leakage. a Only use teries. - the specified bat- This make cause damaged the Monitor or could give an electric shock. FirstepMonvwCcBaSlmPu&df Others 7 Controls of the Monitor <Front Panel Controls> ON/OFF INPUT ON/OFF SELECT VOLUME Main power button Power standby indicator Illuminates red in standby mode Illuminates green when the Monitor is turned INPUT SELECT VOLUME on INPUT SELECT button Sub power button VOLUME ( 8 , ) buttons Remote control sensor <Back Panel> RLVIDEO AUDIO (MONO) AV INPUT RL AUDIO (MONO) VIDEO AV INPUT S-VIDEO Y S-VIDEO PBR P COMPONENT(480i/480p) (DVD INPUT) YPBPR COMPONENTI(480i/480p) (DVD INPUT) AUDIO INPUT RS-232C R () () L EXTERNAL SPEAKER (+) (8Ω) (VGA/SVGA/XGA/SXGA) AUDIO INPUT AC INPUT (+) R AUDIO L RGB-PC INPUT AV INPUT / RS-232C RL () () EXTERNAL SPEAKER 8Ω G (AP-60EA21) (+) EXTERNAL SPEAKER (8 ohm output) COMPONENT (480i/480p) (DVD INPUT) SOCKETS The Interface board is not equipped on MT/Z-60PZ13/14 series models. Contact your dealer for buying this optional item. (+) RL AUDIO RGB-PC INPUT (VGA/SVGA/XGA/SXGA) RGB-PC INPUT AUDIO INPUT/ RS-232C jacks (VGA/SVGA/XGA/SXGA)/ AC INPUT POWER INPUT SOCKET This Monitor operates on an AC mains supply, the voltage is as indicated as inside back cover of this manual. Never apply DC power to the Monitor. FirstepMonvwCcBaSlmPu&df Others 9 Accessories POWER SLEEP INPUT SELECT PSM SSM ARC STILL PIP /TWN PICTURE PIPINPUT POSITION MENU VOL POWER REW MUTE OK VOL STOP P/STILL PLAY FF REC D-sub 15 pin cable Power cord Remote control handset 1.5V LG TV 1.5V ASmark Owner's Manual Alkaline batteries (Optional) Optional - - Extras Optional extras can be changed or modified optional extras can be added. Contract your dealer for buying these items. for quality improvement without any notification PR PB Y (MONO) AUDIO RL INPUT VIDEO (480i/480p) COMPONENT (DVD INPUT) S-VIDEO AV AP-60EA21 AP-60WA20M series (Tilt 10 wall mounting bracket) (interface board) AP-60WA10 series (Wall mounting bracket) new Optional - - Extras Optional extras can be changed or modified optional extras can be added. Contract your dealer for buying these items. for quality improvement without any notification AP-60CA10 series AP-60FA10 series (Ceiling mounting bracket) (Floor type stand) AP-60DA10 series AP-60SA10 series (Desktop stand) (Speakers) AP-60SA10D series AP-60SA10F series (Speaker stand) (Floor type speaker stand) new FirstepMonvwCcBaSlmPu&df Others Video cables Audio cables 11 Controls of the remote control - When using the remote control aim it at the remote control sensor of the Monitor. POWER POWER SLEEP SLEEP (Refer to p.35) PSM (Refer to p.36) ARC (Refer to p.46) INPUT SELECT PSM SSM ARC STILL PIP PIP (Refer to / TWIN PICTURE p.26) PIP INPUT PIP INPUT (Refer to POSITION p.27, 30) MENU MUTE MENU OK OK VOL POWER STOP P/STILL REW PLAY FF VOL VOLUME( , ) VCR BUTTONS controls a LG video cassette recorder. 12 REC INPUT SELECT button on the remote control INPUT SELECT SSM (Refer to Each press of this button the mode p.41) STILL (Refer to TWIN PICTURE p.43) (Refer POSITION (Refer to to changes shown below. Video S-Video RGB Component p.29) p.27) MUTE switches the sound as on or off. Video, S-Video, Component These modes Interface are board : selected when the (not supplied) is installed. G / selects a menu item. The Interface board (AP-60EA21) is not equipped on MT/Z-60PZ13/14 series models. FirstepMonvwCcBaSlmPu&df Others 13 Monitor Installation - The Monitor can desktop type, be installed in various ways such as wall mounting type, etc. Wall Mount Installation ? The monitor can be installed on further information, refer to (For Guide'.) the wall '(Tilt) picture above. mounting bracket Installation as wall the and Setup Tips ? Install this monitor only in a location where adequate ventilation is available. a. 4inch mount minimum allowable clearances for adequate (Wall 1.18inch ventilation) 4inch 4inch 4inch 14 Desktop pedestal installation INPUT SELECT ON/OFF ? The Monitor (For can be installed on a further information, refer to desk as 'Desktop VOLUME shown above. stand Installation and Setup Guide'.) b. (Pedestal mount minimum 4inch 1.18inch allowable clearances for adequate ventilation) 4inch 4inch FirstepMonvwCcBaSlmPu&df Others 2.36inch 15 Watching VCR - When (Video - - - - connecting the Plasma Monitor with external equipments, yellow, Audio(L) white, Audio(R) -red). - match the colours of connecting ports - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor. If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. If 4:3 picture format or still word such as watching VCR or CH label is on the screen that fixed image may remain visible. Avoid having a fixed image remain on the screen for a long period of time. Typically ture from a VCR, 4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen. (MONO) RLVIDEO AUDIO AV INPUT YPBPR RL AUDIO (MONO) VIDEO AV INPUT Y S-VIDEO S-VIDEO PBR P COMPONENT(480i480p) (DVD INPUT) R (+) RL AUDIO RGB-PC NPUT (VGASVGA/XGA/SXGA) AUDIO INPUT RS-232C () L (VGA/SVGA/XGA/SXGA) a long time, frozen still a pic- (+) EXTERNALSPEAKER(8Ω) ACINPUT (+) RL () () (+) R AUDIO L RGB-PC INPUT COMPONENT(480i/480p) (DVD INPUT) for AUDIO INPUT RS-232C EXTERNAL <Back panel SPEAKER(8Ω) AC INPUT of the Monitor> To watch VCR S-VIDEO (When the Interface board is installed.) OUT (R) AUDIO (L) G VIDEO The Interface board IN panel is not equipped Press INPUT SELECT button INPUT SELECT <Back (AP-60EA21) on MT/Z-60PZ13/14 series models. of VCR> on the remote control and select Video. 1Insert (When connecting with S-Video, S-Video.) select the 2 a video tape into the VCR and press the PLAY button on the VCR. See VCR owner's manual. Tips ? 16 To avoid picture noise and monitor. (interference), leave an adequate distance between the VCR Watching Cable - After you to a cable TV service from watch cable TV programming. subscribing can RL AUDO (MONO)VIDEO AV INPUT Y S-VIDEO PBR P Y RL AUDIO (MONO) VIDEO AV INPUT S-VIDEO PB local R (+) RL AUDIO COMPONENT(480i/480p) (DVD INPUT) a RGB-PC INPUT AUDIO NPUT EXT RS-232C (VGA/SVGA/XGA/SXGA) PR TV () RNALSPEA provider (DVD INPUT) R B-PC INPUT R (8Ω) ( RS-232C (VGA/ VGA/XGA/SXGA) AUDIO a converter, AC INPUT (+) AUDIO INPUT <Back installing +) L R AUDIO L COMPONENT(480i/480p) and panel RL () () EXTERNAL (+) SPEAKER(8Ω) AC INPUT of the Monitor> <Cable box> VO TV VCR RF To watch cable TV G The Interface board (AP-60EA21) is not 1 (When the Interface board is installed.) equipped Press INPUT SELECT button Cable on on MT/Z-60PZ13/14 series models. the INPUT SELECT remote control and select Video. Tune to cable service 2 provided channels using the cable box. Others Tips ? For further information regarding cable TV service, contact your local cable TV service provider(s). FirstepMonvwCcBaSlmPu&df 17 external AV Watching - When connecting the Plasma Monitor with external match the colours of AV INPUT AV INPUT S-VIDEO <Back panel equipments, connecting ports. RLVDEO AUDO (MONO) RL AUDIO (MONO) VIDEO source Y S-VIDEO PBR P COMPONENT(480i/480p) (DVDINPUT) YPBPR COMPONENT(480i/480p) (DVD INPUT) R (+) RL AUDIO RGB-PC INPUT AUDO INPUT RS-232C (VGA/SVGA/XGA/SXGA) EXT () RNALSPEA L (+) ER (8Ω) ACINPUT (+) RL () () (+) R AUDIO L RGB-PC INPUT (VGA/S GA/XGA/SXGA) AUDIO INPUT RS-232C EXTERNAL SPEAKER(8Ω) AC INPUT of the Monitor> Camcorder AUDIO RL VIDEO Video game set To watch external AV G The Interface board 1 2 18 (AP-60EA21) is not equipped Press INPUT SELECT button on source (When the Interface board on MT/Z-60PZ13/14 series models. the remote control of the monitor to select Video. Operate the corresponding external equipment. INPUT SELECT is installed.) DVD Watching How to connect (When G ? The Interface board (AP-60EA21) is not the Interface board is equipped on MT/Z-60PZ13/14 series models. Connect DVD video inputs to Y, PB, PR of COMPONENT audio inputs to Audio sockets of AV INPUT. RL AUDIO (MONO)VIDEO AV INPUT RL AUDIO (MONO) VIDEO AV INPUT S-VIDEO Y S-VIDEO PBR P COMPONENT(480i480p) (DVD NPUT) (DVD INPUT) AUDIO INPUT RS-232C (VGA/SVGA/XGASXGA) YPBPR COMPONENT(480i/480p) R (+) RL AUDIO RGB-PC INPUT installed.) EXT () RNALSPEA L (+) R(8Ω) AC INPUT (+) R AUDIO L RGB-PC INPUT RS-232C AUDIO INPUT Back < (R) How to AUDIO Back (L) B panel of a DVD use G The Interface board (AP-60EA21) is not equipped on panel (+) SPEAKER(8Ω) AC INPUT of the Monitor> R player> ? (When the Interface board is installed.) RL () () EXTERNAL (VGA/SVGA/XGA/SX A) < and (480i/480p) (DVD INPUT) Component Input ports can get better picture quality if you connect DVD player with component input You ports as below. MT/Z-60PZ13/14 series models. Component ports ? ? Press INPUT SELECT button on the remote control of the monitor to select Component. Try this after turning on the DVD player. of the Monitor Video output ports of DVD player YPBPR Y Y Y Y Pb B-Y Cb PB Pr R-Y Cr PR 19 FirstepMonvwCcBaSlmPu&df Others Connecting - - PC a Computer Control Source You can easily connect the Plasma Display to your PC for outstanding image and sound. Use the Monitor to display images and sound from a PC Computer source. Setup ? Instructions to Connect PC to your Monitor a If the image output of the PC is set higher than no picture will appear on the Monitor. (UXGA is not supported.) Connect the signal cable from the monitor Output Default monitor. UXGA, ? port on not be used for the Monitor. quality picture. (Look are not supplied To set up the Monitor to operate within a PC windows environment, select Normal, Standard or RLVIDEO AUDIO (MONO) AVINPUT Back How to Y S-VIDEO PBR P COMPONENT(480/480p) (DVDINPUT) YPBPR panel COMPONENT(480i/480p) (DVD INPUT) R RGB PC T (VGA/SVGA/ R (+) RL AUDO RGB-PCINPUT (VGA/SVGA/XGA/SXGA) AUDIO NPUT RS-232C for a x 720 to a sound card, () EXTERNAL SPEA L output of the get the best video card that nVIDIA GeForce 2 pro or similar supports this resolution) Monitor.) S-VIDEO Play It is recommended that the resolution ? ports of the Monitor. (Audio cables AV INPUT and adjust PC should be set to 1280 RL AUDIO (MONO) VIDEO Plug If your PC computer is equipped with the sound output on the PC. ? Connect the audio cable from the PC to the Audio with the ? on can functionality. the PC to the RGB-PC INPUT (VGA/SVGA/XGA/SXGA) port ? The Monitor ? chipset uses the that (+) AC NPUT ER(8Ω) (+) AUDIO AUD O INPUT RS-232C RL () () EXTERNAL SXGA) (+) AC INPUT SPEAKER(8Ω) of the Monitor use PC ? INPUT SELECT On the remote control Setup computer and press the ON/OFF button on the power to it. Second, turn on the display by pressing the button on the Monitor or by pressing the POWER button on the Monitor's remote control. Use the INPUT SELECT button on the remote control to select the RGB input source. Set the resolution output of the PC to SXGA or under (1280 x 1024, First, turn Monitor to ? ? on the PC apply 75Hz). (Refer to page 21.) Tips ? Avoid keeping a fixed image on the Monitor's screen permanently imprinted on the screen; use a become ? 20 If the resolution output of the PC computer is (VGA/SVGA/XGA/SXGA) input port accordingly. on over for a SVGA, the Monitor. long period screen saver of time. The fixed when image possible. connect the PC to the RGB-PC Change the PC computer resolution output may Monitor Image Display Specifications Resolution Horizontal Vertical Frequency (KHz) Frequency (Hz) 640x350 720x400 640x480 800x600 832x624 1024x768 1280x720 1152x864 1152x870 1280x960 1280x1024 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 45.913 90.03 53.011 100.04 64.062 120.00 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 56.000 90.00 64.016 100.00 49.725 74.55 48.363 60.00 56.476 70.06 60.023 75.02 68.677 84.99 52.400 69.98 54.348 60.05 63.995 70.01 67.500 75.00 77.487 85.05 68.681 75.06 60.000 60.00 75.000 75.00 63.981 60.02 79.976 75.02 FirstepMonvwCcBaSlmPu&df Others Tips ? Synchronization input form : separate 21 Function - - Select RGB input in PC mode checking source. PIP/DW function is worked when the interface board is installed. Interface board (AP-60EA21) MENU is not equipped on MT/Z-60PZ13/14 series models. Press the MENU button. 1 Press the 2 ? D / E button. Each time you press this button you PSM G 85G Brightness 50G Colour 50G Tint 0G Sharpness OK G 50G MENU <Picture SSM G Treble 50G Bass 50G Balance 0G OK G MENU <Sound Language G G Screen G Transparency G PIP/DW G Set ID G DE G Temp. OK G MENU <Special ? ? menu> ARC Colour ? menu> G AVL DE below. G DRP Contrast DE can see menus as menu> The PIP works in VGA, SVGA, XGA, 60Hz. The TWIN PICTURE works in VGA, 60Hz. Only adjust Colour Temperature function in MT-60PZ12/14 series / MZ-60PZ14 series models. VOL VOL 223 Press the G button and then press the D / E / G button to select a function you want to F ? Press the OK button to exit. or use. Adjusting Auto - - - in PC mode configure Select RGB input source Automatically adjusts picture position and eliminates any image shaking. When watching PIP/TWIN PICTURE, Screen option is not available in menu. READY Press the MENU button and then press the select menu. Press the G MENU D 2 D button to / E Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Temp. GToSet G button to select and then press Auto-configure the G button. Auto-configure G GToSet G G Phase G Reset G VOL ? ? If 3 Conectis VOL VOL Press the E button. Press the D / E button to select Screen and then press the G button. 1 / FirstepMonvw When Auto.configure has finished, "OK" will be shown on screen. If the position of the image is incorrect, try Auto adjustment again. picture needs ,and Phase. to be adjusted more after auto adjustment, adjust BasicopertnSlmPu&df Others Tips ? If the image is still not correct, your Monitor is functioning properly but needs further adjustment. 23 Adjusting Adjusting - and Only adjust in PC mode horizontal / vertical in position component 480i/480p. READY Press the MENU button and then press the select menu. Press the G / E VOL Press the D / E button to select Screen and then press the G button. VOL Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Press the D / E button to select then press the G button. 2 button to button. MENU 1 D or Temp. GToSet G and Auto-configure G G 0 G VOL ? ? 3 Select Select G Reset G for vertical position adjustment. for horizontal position adjustment. Press the F / G button to adjust until you get desired horizontal vertical position and then press the OK button. ? ? or The adjustment range of is -50 +50. The adjustment range of is -100 +100. Based on the input mode, the adjustment range of or may change. Based on the input signal, the position of the picture may not change even though you have adjusted the horizontal or vertical position with this function. ~ ~ ? VOL 24 Phase VOL OK FirstepMonvw Adjusting phase - - If the picture isn't clear after auto adjustment and especially that characters are still bling, then adjust the picture phase manually. When watching PIP/TWIN PICTURE, Screen option is not available in Special menu. trem- READY Press the MENU button and then press the select menu. Press the ( G MENU 1 ) / E Conectis button to button. VOL Press the D / E button to select Screen and then press the G button. VOL 2 D Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Press the D / E button to select Phase and then press the G button. Temp. Auto-configure BasicopertnSlmPu&df GToSet G G G G VOL Press the 3 / F G button to Phase G Reset G 30 adjust phase and then press the OK but- ton. ? The adjustment range of Phase is 0 63. ~ OK VOL VOL Others Initializing ? To initialize the adjusted value, select Reset with the press the G button. D / E button and then 25 PIP function - - - - - - - - before pressing PIP only when the interface board is installed. Interface board (AP-60EA21) is not equipped on MT/Z-60PZ13/14 series models. This function works only in the following resolution; 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz) When you select RGB for main picture in PIP/Twin picture, you can watch video, cable TV or DVD sub picture. Colour of main picture may be different from sub picture's in PIP/Twin picture mode. If input source for main picture is changed while in PIP/Twin picture mode, sub picture will disappear. When watching PIP/Twin picture, Screen option is not available in menu. With PIP active, not all picture formats can be used for the main/sub picture. Select RGB input source This function works Watching PIP the PIP (Picture in Press the PIP button. ? Each time you press PIP PIP size as below. PIP or F / button, you G PIP [L] [S] PIP F PIP[S] G <Small PIP> PIP F PIP[L] G PIP> <Large PIPFOff G <Off> 26 Picture) can change Off the for Selecting PIP INPUT the Press the PIP INPUT button in PIP mode. ? Each time you press PIP INPUT button, you S-Video and Component. Component PIP Moving POSITION FirstepMonvw input signal Input F source Video the Sub only toggle Video, works in 480i mode. Conectis G BasicopertnSlmPu&df picture Press the POSITION button in PIP mode. ? Each press of the POSITION button will change the the sub picture on the screen as shown below. position of Others 27 PIP function Selecting - - - - options before pressing PIP only when the interface board is installed. Interface board (AP-60EA21) is not equipped on MT/Z-60PZ13/14 series models. This function works only in the following resolutions; 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz) To use this function, connect PC video port to RGB-PC INPUT(VGA/SVGA/XGA/SXGA) Select RGB input source This function works connect PC audio - PIP sound Sound Select is port socket and to AUDIO INPUT. always selected Sound[M] regardless of prior sound choice. READY Press the MENU button and then press the select menu. Press the ( G MENU 1 ) Press the D / E button to select Sound Select and then press the G button. VOL 3 Press the Sound button to / E button to select Sound [M] [S] and then press the OK button. Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Temp. G DW G PIP G Input G Sound Select G Sound [M] Position G Sound [S] DW G PIP G Input G Sound Select G Sound [M] Position G Sound [S] D OK 28 E VOL Press the D / E button to select PIP/DW and then press the G button. or / button. VOL 2 D GToSet Twin - - Select RGB picture input mode FirstepMonvw source. only when the interface board is installed. (AP-60EA21) is not equipped on MT/Z-60PZ13/14 series models. This function works only in the following resolutions; 640x480 (only in Vertical frequency 60 Hz) With TWIN PICTURE active, not all picture formats can be used for the main/sub picture. This function works Interface board - - / TWIN PICTURE Conectis Press the /TWIN PICTURE button. ? Each time you press /TWIN PICTURE can select On or Off. or F Main / G button, you picture Sub ? DW FOnG <ON> picture showing a fixed image on the screen, sub picture moves every 2 To avoid BasicopertnSlmPu&df hours. :Center Upside Downside ? Center Sub picture of TWIN PICTURE is always located in center position at first and movement of sub DW ? <OFF> picture operate. FOffG It's not out of order occur sub even horizontal noise in blanking part of though a picture. Others 29 Twin picture Selecting PIP INPUT mode a source picture Press the PIP INPUT button in TWIN PICTURE mode. ? Each time you press PIP INPUT button, you S-Video and Component. Component PIP 30 for the Twin Input source F Video only G works with 480i toggle Video, signal input. Using Inserting the remote control ? the Open battery compartment cover on side and insert the batteries with correct ? Apply two 1.5V alkaline batteries of AAA Don't mix the used batteries with ? Notes for Make sure objects FirstepMonvw batteries using there are no between the new Install the batteries with the correct the back polarity. Conectis type. batteries. polarities. BasicopertnSlmPu&df the remote control Don't place near a the remote control heater remote control and its Strong impact sensor. trol may or cause damp place. on the remote operation con- failure. Signal from the remote control may be disturbed by sun light or other strong light. In this case, turn the set to other direction. Others 31 Turning - When using Turning on the Monitor just Connect power cord 1 sensor on the Monitor the Monitor. after installation correctly. Press the ON/OFF button on the Monitor. At this moment, the Monitor is or INPUT SELECT button on the standby mode. Press the 2 switched to Monitor or press the POWER or INPUT SELECT button and then the Monitor will be switched on. Turning 1 the remote control, aim it at its on on the Monitor (power cord is still If the Monitor is turned off with the on the remote control connected) button on the Monitor or INPUT SELECT button on the Monitor or press the POWER INPUT SELECT button on the remote control and then the Monitor will be switched on. Press the or 2 3 If the Monitor is turned off with the ON/OFF button ? Press the ON/OFF button the Monitor to turn on on the Monitor the Monitor. If the Monitor is turned off with the remote control and also the ON/OFF button on the Monitor ? Press the ON/OFF button on the Monitor and then press the or INPUT SELECT button on the Monitor or press the POWER or INPUT SELECT button on the remote control and then the Monitor will be switched Tips Adjusting Volume( ) ? sound. 32 on volume level button increases the sound and volume( ) on. button decreases the the Selecting language on screen READY Press the MENU button and then press the select menu. Press the G E button to VOL / E button to select Language and then press the G button. Press the / button. MENU 1 D D Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Temp. G VOL 2 3 Press the D / E button to select the desired language. Press the OK button. OK FirstepMonvwCcBaSlmPu&df Others 33 Function - Select VIDEO input source. Press the MENU button. 1 MENU checking Press the 2 ? D / button. E Each time you press this button you shown below. PSM G DRP G Contrast 100 50G Colour 50G Tint 0G Sharpness OK G 50G MENU <Picture SSM menu> G AVL G Treble 50G Bass 50G Balance DE 0G OK G MENU <Sound menu> Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour DE G Temp. OK G MENU <Special ? G Brightness DE can see menus Only adjust Colour Temperature menu> function in MT-60PZ12/14 series / MZ-60PZ14 series models. VOL VOL 3 Press the G button and then press the D / E / G button to select a function you want to F ? 34 Press the OK button to exit. or use. Setting sleep Sleep Timer turns the SLEEP time Monitor off after a preset time Press the SLEEP button to set sleep time. Each time you press SLEEP button, the next preset setting time is changed as shown below. F---G F10G F20G F30G F120G F90G F60G F240G F180G F ? To release F ?' / G G sleep time setting, press the SLEEP or G repeatedly to select F one minute before the Monitor displayed, button 1' is --- --- . is due to switch off. Tips ? ? ? When the sleep time you want is displayed on the screen, don't press the SLEEP button. After 20 seconds, the screen display disappears and sleep time is set. To check remaining FirstepMonvwCcBaSlmPu&df Others sleep time after setting, press the SLEEP button just once. If you turn the Monitor off after setting the sleep timer, the setting is erased. The sleep timer will then have to be set again. 35 Auto picture control Use PSM to set the Monitor for the best - This function is not available in RGB, PIP/TWIN PICTURE. PSM PSM 1 2 (Picture Status Memory) Press the PSM button. Press the PSM or F / G button to select your desired picture condition. PSM ? F Each press of shown below. Dynamic ? ? Dynamic F / G G button changes Mild the screen display as User You can also select Dynamic, Mild or User in the Picture menu. The picture Dynamic, Mild and User are programmed for good picture reproduction at the factory and cannot be changed. 36 picture appearance. Adjusting picture - PIP and Twin picture inset settings are not condition adjustable. READY Press the MENU button and then press the select menu. Press the G / E button to button. MENU 1 D VOL Use the D / E button to select Contrast and then press the G button. (to adjust contrast setting) PSM G DRP Contrast G 100 G Brightness 50G Colour 50G Tint Sharpness 0G 50G VOL ? 2 Adjust Brightness, Colour, Tint Sharpness in the same way. Use the / F G and button to make appro- priate adjustments and then press the OK button. ? Press the D / E button to select other items. PSM DRP Brightness 50G Colour Sharpness VOL G 70G Tint VOL G Contrast 0G 0G 50G OK FirstepMonvwCcBaSlmPu&df Others 37 DRP Picture) (Digital Reality Clear Soft DRP allows you to select - for your or picture appearance. This function works in video, component 480i mode. READY Press the MENU button and then press the select menu. Press the G Press the D / E button to select DRP and then press the G button. D Dynamic / or button to select Mild. 38 100 G Dynamic G Mild Brightness 50G Colour 50G Sharpness 0G 50G E APC Press the OK button. G DRP Contrast 100 G Dynamic G Mild Brightness 50G Colour 50G Sharpness OK G DRP Tint 3 button to PSM Contrast Tint Press the E VOL VOL 2 / button. MENU 1 D 0G 50G Selecting - Use this option when viewing menu the video options input. READY Press the MENU button and then press the select menu. Press the G Use the D / E button to select Screen and then press the G button. ? Select the VCR option if watching Select the TV option for other equipment.(Except VCR) ? button to Language G ARC G Screen G TV Transparency G VCR PIP/DW G Set ID G Colour UsetheD/E buttontoselectTVor VCR. ? E VOL VOL 2 / button. MENU 1 D a VCR. Temp. Language G ARC G Screen G TV Transparency G VCR PIP/DW G Set ID G Colour Temp. Each time you press the D / E button you toggle between TV and VCR. VOL 3 Press the OK button. FirstepMonvwCcBaSlmPu&df Others OK 39 sound Adjusting READY Press the MENU button and then press the select menu. Press the G / E button to button. MENU 1 D VOL Use the D / E button to select Treble and then press the G button. (if adjusting treble) SSM G AVL G Treble 50 Bass 50G Balance G 0G VOL ? 2 Adjust Bass and Balance in the Use the / way. button to make appropriate adjustment and then press the OK button. ? F Press the D G / E button to select other OK VOL 40 same VOL options. SSM AVL G G Treble 70G Bass 50G Balance 0G Auto sound control SSM ? SSM This function lets you enjoy the best sound without any special adjustment because the Monitor automatically selects the appropriate sound option based on the program content. 1 Press the SSM button. 2 Press the SSM desired sound. SSM ? or F / button to select your G FUserG Each press of SSM as below. or F / G button changes the screen dis- play Flat User ? ? Movie Speech Music You can also select Flat, Speech, Movie, Music or User in the Sound menu. The sound Flat, Speech, Movie and Music are programmed for good sound reproduction at the factory and cannot be changed. FirstepMonvwCcBaSlmPu&df Others 41 AVL (Auto Volume Leveler) This feature maintains an equal volume level; even if you change channels. READY Press the MENU button and then press the select menu. Press the G / E button to button. MENU 1 D VOL Press the D / E button to select AVL and then press the G button. SSM AVL G G On Treble 50G Off Bass 50G Balance 0G VOL 2 PresstheD/E buttontoselectOnor Off. SSM AVL G On 50G Off Bass 50G Balance 3 42 Press the OK button. OK G Treble 0G Using Still - This feature isn't available for RGB 1 STILL input function source. Press the STILL button. ? You ? The sub can still the current picture picture. is stilled in PIP or Twin picture mode. <Moving image> <Still 2 To return to normal image> viewing, press the STILL button again. Tips ? FirstepMonvwCcBaSlmPu&df Others If still picture is on the screen for more than 5 minutes, the image becomes dark. If another function is activated, normal brightness of the screen is restored. 43 Adjusting OSD Transparency READY Press the MENU button and then press the select menu. Press the G / E button to button. MENU 1 D VOL Press the D / E button to select and then press the Transparency G button. Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Temp. 5 G VOL 2 Press the G button to The adjustment range of 0~5. VOL VOL Press the OK button. OK 44 / adjust OSD transparency. ? 3 F Transparency is Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Temp. G 3 Adjusting - (option) adjust colour temperature in PC mode again although input source. adjusted value, select '0' in Red, Green and Blue. You should be adjusted - colour temperature colour temperature is in other To initialize READY Press the MENU button and then press the select Press the menu. G button to VOL Press the D / E button to select Colour Temp. and then press the G button. VOL Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour 2 E button. MENU 1 / D Press the D / E button to select Red and then press the G button. (to adjust Red setting) Temp. Red G G Green G Blue G G ToSet 0 VOL ? 3 Adjust Green and Blue in the same Use the F / G button to make press the OK button. VOL ? The VOL adjustment way. appropriate adjustments and then OK range of Red, Green and Blue is -5 FirstepMonvwCcBaSlmPu&df Others +5. ~ 45 Setting picture format - You are - If 4:3 is - Don't ARC available to 16:9 on the screen or for display 4:3 picture a 4:3 in RGB. long time, format or that fixed image may TWIN PICTURE remain visible. on screen Press the ARC button to select format. ? above 10 hours a desired Each time you press ARC or F / G button, you select 16:9, 4:3 or Zoom alternatively. continuously. picture can ARCF16:9G <16:9> ARCF4:3G <4:3> ARCFZoomG <Zoom> ? 46 You can also select 16:9, 4:3 or Zoom in the Special menu. External Control Device - Connect the RS-232C input jack to an external control device and control the Monitor's functions externally. (such as a Setup computer or an A/V control system) How to connect external control ? ? ? equipment Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. RS-232C connection cables are not supplied with the Monitor. The Monitor remote control and front panel controls (except main power) will not be functional if the Monitor is controlled by a PC computer or other external device. RLVIDEO AUDO MONO) AVINPUT RL AUDIO (MONO) VIDEO AV INPUT S-VIDEO Y S-VIDEO YPBPR COMPONENT(480i/480p) (DVD INPUT) PBR P COMPONENT(480i/480p) (DVDINPUT) (+) RL AUDIO RGB-PCINPUT (VGA/SVGA/XGA/SXGA) AUDIO INPUT RS-232C R ) EXTERNAL () L (+) SPEAKER(8Ω) AC INPUT (+) RL AUDIO RGB-PC INPUT (VGA/SVGA/XGA/SXGA) AUDIO INPUT R2C RL () () EXTERNAL (+) SPEAKER(8Ω) AC INPUT Monitor Rear Connections Panel FirstepMonvwCcBaSlmPu&df Others 47 External Control Device Type of connector No. Pin 1 No connection : D-Sub 9-pin Adjustments male name 2 RXD 3 TXD (Receive data) (Transmit data) (DTE side ready) 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 No Connection (DCE side ready) (Ready to send) (Clear to send) 1 5 Pin No.4 and Pin 9 No.6 must be connected on 6 monitor side. * Use a null modem cable. Wire the 7-Wire cable so that each pair of data lines cross between the two devices. These data line pairs (Receive data) and TXD (Transmit data), DTR (DTE side ready) and DSR (DCE side ready), and RTS (Ready to send) and CTS (Clear to send). When using the 3-Wire cable connected to RXD, TXD and GND; Pin No. 4 (DTR) and Pin No. 6 (DSR) must be connected to the monitor. (The cable must be disconnected from the Monitor to be able to use the remote control and Monitor front panel controls.) With the RS-232 input connected, the Monitor cannot be controlled by both an external control device and the remote control at the same time. The Monitor can only be controlled by either the remote control or the are * RXD external control device. 48 RS-232C configurations 7-wire (Standard 3-wire configuration (Not standard) configuration RS-232C cable) PC PDP PC PDP TXD RXD 2 3 TXD RXD 2 3 TXD 3 2 RXD TXD 3 2 RXD GND 5 5 GND GND 5 5 GND DTR 4 6 DSR DTR 4 4 DTR DSR 6 4 DTR DSR 6 6 DSR RTS 7 8 CTS RTS 7 7 RTS CTS 8 7 RTS CTS 8 8 CTS DB9 DB9 DB9 DB9 Control line 7-Wire Cable ? 3-Wire Cable Configuration The Monitor is available to switch between external adjustment and remote control adjustment using a control line. Note: If the control line is When using Configuration a 3-Wire cable configuration there is control line. The external control device must no put the Monitor into the high, the monitor is con- trolled by line is low, the Monitor is controlled by the Monitor's the external control device. If the control remote control. ? "change into remote control adjust(see page 55). The Monitor will then be controlled by the remote control. If the ment mode" able to be Monitor is turned back on, it will revert back to external device control. FirstepMonvwCcBaSlmPu&df Others 49 External Control Device Adjustments Set ID ? Use this function to specify a monitor ID number. READY Press the MENU button and then press the select menu. Press the G / E button to button. MENU 1 D VOL UsetheD/E buttonstoselectSetIDand then press the G button. Language G ARC G Screen G Transparency G PIP/DW G Set ID G Colour Temp. 1 G VOL 2 Usethe F /G buttontoadjust SetIDto choose the desired monitor ID number. ? The VOL 50 adjustment VOL range of Set ID is 1 99. Language G ARC G Screen G Transparency G PIP/DW G Set ID G ~ Colour Temp. G 1 - The RS-232C is used to control the Monitor's functions input jack Communication Parameters ? Baud rate ? Data : 2400 length : 8 ? Parity : None ?Stopbit:1bit ? external control device. an Transmission / Receiving Protocol Transmission bps (UART) bits [Command][ ][Set ID][ ][Data][Cr] * Communication code using : ASCII code * [Command] [Set ID] : To control PDP set. : You can adjust the set ID to choose desired monitor ID number in * If the command interval is seconds, only Command Be careful when using interrupted for more 1 will be recognized. than 4 See page 50. is1~99. menu. the power command. When selecting Set ID special Adjustment range '0', every connected PDP set is controlled. * [DATA] : To transmit command data. Transmit 'FF' data to read status of command. * [Cr] : Carriage Return ASCII code '0x0D' *[] Command Reference List : ASCII code 'space (0x20)' OK Acknowledgement [Set ID][:][OK][x][Data][x] NAME COMMAND 01. Power DATA RANGE p 0~1 i 0~3 r 0~2 04. Screen mute m 0~1 05. Volume mute w 0~1 06. Volume control v 0~64 07. Contrast k 0~64 b 0~64 c 0~64 02. 03. 08. Select Input Aspect Ratio Brightness 09. Colour * on 10. Tint t 0~64 11. s 0~64 12. OSD select d 0~1 13. Abnormal state a 0~1 14. PIP/DW z 0~3 15. PIP select e 0~1 16. PIP sound select u 0~1 17. PIP x 0~3 j 0~1 input position 18. remote control adjustment this format when (acknowledgement) based receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Set ID][:][NG][x] * Sharpness The Monitor transmits ACK The Monitor transmits ACK on this format when non-viable functions (acknowledgement) based receiving abnormal data from or communication errors. FirstepMonvwCcBaSlmPu&df Others mode 51 External Control Device 01. Power 03. (Command:p) G To control Power On/Off of the Monitor. G Aspect To adjust You [p][ ][Set ID][ ][Data][Cr] 0 : for set ID No.3. Data Acknowledgement [Set ID][:][OK][x][Data][x] 0 : In example : 0 : Wide 1 : Normal 2 : Full (16:9) (4:3) (Zoom) screen screen screen [Set ID][:][OK][x][Data][x] Data Monitor Acknowledges power on for set ID No.3. G format. also can Acknowledgement Power Off 1:PowerOn * (Command:r) screen [r][ ][Set ID][ ][Data][Cr] Example : Power on Type:P31'0x0D' Data the Transmission Power Off 1:PowerOn * Ratio adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Special menu. Transmission Data Adjustments 0 : Wide 1 : Normal : Full 2 To show Power On/Off. * Using the PC (16:9) (4:3) (Zoom) screen screen screen input, you select either 16:9 or 4:3 screen aspect ratio. Transmission [p][ ][Set ID][ ][FF][Cr] 04. Screen mute Acknowledgement To select [Set ID][:][OK][x][Data][x] G Data Transmission 0 : Power Off 1 : Power On 2 : Power On 3 : Power On 4 * Power On 02. presents To select You can status about each function. select Input input source on an [i][ ][Set ID][ ][Data][Cr] 0 :RGB 1 : 2 : 3 : AV (Video) Component S-AV (S-Video) [Set ID][:][OK][x][Data][x] 52 0:RGB 1 : 2 : 3 : AV Screen mute : Screen mute off on (Picture off) (Picture on) [Set ID][:][OK][x][Data][x] 0 : Screen mute 1 : Screen mute off on (Picture off) (Picture on) for the Monitor. input source using the INPUT 05. Volume mute G (Video) Component S-AV (S-Video) (Command:w) To control volume mute on/off. You can also adjust mute using the MUTE button remote control. Transmission [w][ ][Set ID][ ][Data][Cr] Data Acknowledgement Data : 1 Acknowledgement Data the Monitor's remote control. Transmission Data 0 (Command:i) also select SELECT button mute on/off. [m][ ][Set ID][ ][Data][Cr] Data In like manner, if other functions transmit 'FF' data based on this format, Acknowledgement data feed back G : (RGB) (Video) (Component) (S-Video) screen (Command:m) 0 : Volume mute 1 : Volume mute off on (Volume off) (Volume on) Acknowledgement [Set ID][:][OK][x][Data][x] Data 0 : Volume mute 1 : Volume mute off on (Volume off) (Volume on) on 06. Volume control G To on volume. adjust You also can 09. Colour (Command:v) G adjust volume with the volume buttons remote control. To the screen also adjust adjust You can (Command:c) colour. colour in the Picture menu. Transmission Transmission [c][ ][Set ID][ ][Data][Cr] [v][ ][Set ID][ ][Data][Cr] Data Data Min:0~Max:64 Min:0~Max:64 Refer to 'Real data * as shown below. as shown below. [Set ID][:][OK][x][Data][x] [Set ID][:][OK][x][Data][x] Data Min:0~Max:64 Min:0~Max:64 10. Tint G To 07. Contrast To adjust You screen also can (Command:k) can adjust Data menu Red:0~Green:64 Refer to 'Real data * mapping' as shown below. Acknowledgement [Set ID][:][OK][x][Data][x] Min:0~Max:64 Refer to 'Real data tint. tint in the Picture menu. [k][ ][Set ID][ ][Data][Cr] * screen [t][ ][Set ID][ ][Data][Cr] contrast in the Picture Transmission Data the also Transmission contrast. adjust (Command:t) adjust You G mapping' Acknowledgement Acknowledgement Data Refer to 'Real data * mapping' mapping' as shown below. Data Red:0~Green:64 Acknowledgement [Set ID][:][OK][x][Data][x] Data 11. Min:0~Max:64 G Sharpness (Command:s) To the adjust You can also sharpness. adjust sharpness in screen the Picture menu Transmission 08. [s][ ][Set ID][ ][Data][Cr] Brightness (Command:b) Data G To adjust You also can brightness. adjust brightness Min:0~Max:64 * screen in the Picture menu. Refer to 'Real data [Set ID][:][OK][x][Data][x] [b][ ][Set ID][ ][Data][Cr] Data shown below. Min:0~Max:64 Min:0~Max:64 * Refer to 'Real data Acknowledgement [Set ID][:][OK][x][Data][x] Data as Acknowledgement Transmission Data mapping' mapping' as shown below. * Real data 0 mapping :Step0 A:Step10 Min:0~Max:64 Others F:Step15 10:Step16 64 : Step FirstepMonvwCcBaSlmPu&df 100 53 External Control Device 12. OSD select G To select OSD (Command:d) (On Screen Display) 14. PIP / DW on/off. G :OSDoff 1 :OSDon [Set ID][:][OK][x][Data][x] :OSDoff 1 :OSDon main 0 :PIP/DWoff 1 : 2 : 3 : PIP (small) (large) Twin picture (DW) PIP Acknowledgement The remote control and Monitor front (except on [z][ ][Set ID][ ][Data][Cr] Acknowledgement Data 0 (Picture-in-Picture) or twin picture (DW). using the pip/twin picture remote control or in the Special menu. also control PIP/DW Transmission Data * can button [d][ ][Set ID][ ][Data][Cr] (Command:z) To control PIP You Transmission Data 0 Adjustments power) are is set up to be controlled not by panel controls operable when the Monitor the PC [Set ID][:][OK][x][Data][x] Data computer. * PIP 0 :PIP/DWoff 1 : 2 : 3 : PIP (small) (large) Twin picture (DW) PIP following resolutions: (VGA) / 800x600(SVGA) / 1024x768 (XGA) (only in vertical frequency 60Hz), Component 480p / 720p / 1080i. Twin picture works only in the following resolutions: RGB PC 640x480 (VGA) (only in vertical frequency 60Hz), Component 480p. only works in the RGB PC 640x480 * 13. Abnormal state G To recognize an (Command:a) abnormal state. Transmission 15. PIP [a][ ][Set ID][ ][FF][Cr] Acknowledgement G Data 0:OK 1 : input source also select can the remote control (Command:e) for sub source or in the picture in PIP mode. using PIP input button on Special menu. Transmission [e][ ][Set ID][ ][Data][Cr] :ACdown Data * select Fan alarm 2:5Vdown 3 To select You [Set ID][:][OK][x][Data][x] input This function is "read only". 0 : AV 1 : COMPONENT 2 : S-AV (VIDEO) (S-VIDEO) Acknowledgement [Set ID][:][OK][x][Data][x] Data * 54 0 : AV 1 : COMPONENT 2 : S-AV (VIDEO) (S-VIDEO) COMPONENT source only works with 480i input signal. 16. PIP sound select G To select main You can special sub or 18. (Command:u) (inset) sound for PIP/Twin also select sound select in PIP/DW on Change into Remote control adjustment mode (Command:j) picture. the G menu. To control the Monitor with the remote control while the cable is still connected. Transmission Transmission [u][ ][Set ID][ ][Data][Cr] Data [j][ ][Set ID][ ][Data][Cr] picture sound 1 : Sub picture sound Acknowledgement 0 : Main Data * 0 : Main 1 : Sub source Remote control adjustment mode [Set ID][:][OK][x][Data][x] picture sound picture sound COMPONENT : Acknowledgement [Set ID][:][OK][x][Data][x] Data 1 only Data works in 480i input signal. * 0 : PC 1 : Remote control If external "change Monitor adjustment equipment mode adjustment mode commands the Monitor to into remote control can only be adjustment mode", the adjusted by the remote control. To revert the Monitor control to external control device adjustment, 17. PIP G on again. position (Command:x) To select sub You turn the Monitor off and then can also picture position for PIP. adjust the sub picture position using position button on the Special menu. the remote control or the in PIP/DW on Transmission [x][ ][Set ID][ ][Data][Cr] Data down 0 : Right 1 : Left down 2 : Left up 3 : on screen on screen on screen Right up on Acknowledgement screen [Set ID][:][OK][x][Data][x] Data down 0 : Right 1 : Left down 2 : Left up 3 : Right on screen on screen Others on screen up FirstepMonvwCcBaSlmPu&df on screen 55 Note 56 Note FirstepMonvwCcBaSlmPu&df Others 57 check list Troubleshooting No picture & ? Check whether the Monitor is turned ? Power cord inserted into wall outlet? ? Plug another product's power cord into the wall outlet where the Monitor's power cord was plugged in. ? Press the VOLUME ? Sound muted? Press MUTE button. ? Check to on. No sound Picture OK & No sound Display The remote control ? doesn't work No or or Poor colour Poor picture output from one of the speakers Strange sound from the Monitor 58 button. see if there is any object between the Plasma and the remote control causing obstruction. Check to see if the batteries polarities. (Refer to are installed with the correct p.31) ? Install ? Select Colour in the Picture (G ) button. (Refer to p.37) ? Keep ? Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the new a screen No (G ) ? Adjust ? Typical faulty. batteries. (Refer to p.31) menu and press the VOLUME certain distance between the Monitor and the VCR. gets dark.) Balance in the Sound menu. sound due to normal Monitor (Refer to operation, p.40) Monitor is not Product MODEL Width (inches / mm) MT-60PZ11/B/G/K/S / MT-60PZ12/A/B/K/S MT-60PZ14/A/B/K/S / MZ-60PZ13/B/G/K/S MZ-60PZ14/A/B/K/S 57.3 / 1455 Height (inches / mm) 34.8 / 883 Depth (inches / mm) 3.9/99 Weight (pounds / kg) 154.3 / 70 Power requirement Resolution Colour Temperature Humidity ? specifications 110-240V~50/60Hz 1280 x 720 (Dot) 16,770,000 (256 steps of each R, G and B) 0~40°C under 80% The specifications shown above may be changed without notice for quality improvement. FirstepMonvwCcBaSlmPu&df Others 59 P/NO : 3828VA0330A b (NP00KB, 067M TX, 373-026H)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement