advertisement
▼
Scroll to page 2
of 55
MP-42PZ15/15H Please read this operating owner 's manual carefully before the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached and require Serial number : the back of the Monitor to your dealer when you service. Model number P/NO on quote this information : : PLASMONITR MP-42PZ15A/15AH MP-42PZ15B/15BH MP-42PZ15G/15GH MP-42PZ15K/15KH MP-42PZ15S/15SH OWNER'S MANUAL 3828VA0296R (NF01DC) ON/OFF INPUT SELECT VOLUME What is a Plasma ? Display If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance. At this moment, light is emitted. A Plasma Display is a next generation flat Display using 160° - this Wide phenomenon. angle range of vision A Plasma Display provides more than 160° without distortion from any direction. Easy angle range that you can products so get a picture same class that you can screen The screen of theater. a Plasma Multimedia Plasma A Plasma Display is 42" so can explanation that you can get vivid experience as if you are in a Display be connected with Display ference, game, internet and so on. The so installation A Plasma Display is much lighter and smaller than other install the Plasma Display at the desired place. Big of vision a computer so about colored dots may be that you can use present on it as a screen PDP for con- screen The PDP which is the display device of this product is composed of 0.9 to 2.2 million cells and a few cell defects can occur in the manufacture of the PDP. Several colored dots visible on the screen would be acceptable, in line with other PDP manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product which corresponds to this standard is regarded as acceptable. It means that it could not be changed or refunded. We promise that we'll do our best to develop our technology to minimize the cell defects. WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. * When connecting only and the PDP the PDP tuner with its exclusive cable, most functions work with the tuner as monitor (For further information, refer to the PDP tuner guide). functions ON/OFF INPUT VOLUME SELECT Table of Contents First step Safety instructions ....................................................4 Monitor Overview Controls of the monitor .............................................8 Controls of the Remote Control..............................12 Monitor Installation .................................................14 Equipment Connections and Setup VCR Setup..............................................................16 Cable TV Setup ......................................................18 External AV Source Setup ......................................19 DVD Setup..............................................................20 Setup ..............................................................21 PC Setup ................................................................22 PC Mode Feature Check(Overview) ......................24 PC Mode Adjustments ............................................25 Picture In Picture(PIP) function ..............................28 DTV Basic Features Setup and Operation Turning on the Monitor ...........................................31 Selecting language for the menus..........................32 Checking features...................................................33 Sleep Timer Setting Sleep Timer (Monitor turn-off time) ............34 Picture & Sound Auto picture control ................................................35 Adjusting picture appearance .................................36 DRP (Digital Reality Picture) ..................................37 Adjusting Sound: Bass, Treble, Balance ................38 Auto Sound Control ................................................39 AVL (Auto volume leveler) ......................................40 Special Features Using Still function ..................................................41 Using the screen options ........................................42 Adjusting OSD Transparency .................................43 Adjusting color temperature ...................................44 Setting picture format .............................................45 External control device adjustment ........................46 Others Troubleshooting check list ......................................54 Product specifications.............................................55 Safety - - Instructions Use the MP-42PZ15 series models (Monitor) at the place lower than the altitude of 3281 feet (1000m) to get the best quality of picture and sound. Use the MP-42PZ15H series models (Monitor) at the place lower than the altitude of 6562 feet (2000m) to get the best quality of picture and sound. WARNING Indorstali NOTES Do not place the Monitor in direct sunlight or near heat sources such as heat registers, stove and so on. This may - cause a This plasma be mounted display is designed horizontally (wide to viewing). fire. WARNING Do not the Monitor in such as a bathany place where it use damp place room or OutdorInsali is likely to get wet. Bend antenna cable between inside and outside building to prevent rain from flowing in. - This may cause a fire or could give an electric shock. - WARNING NOTES Earth wire should be connected. - - Power - If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage. If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician. Do not connect ground to telephone wires, lightning rods or gas pipe. Short-circuit breaker 4 This may cause water damaged inside the Monitor and could give an electric shock. Never touch the power with a wet hand. - This may cause an plug electric shock. * Safety instructions have two kinds of WARNING NOTES information, and each meaning of it is below. as The violation of this instruction may cause serious The violation of this instruction may cause light injuries injuries or and even damage death. of the product. Take care of danger that may happen under specific condition. NOTES Disconnect from the mains and remove all connections before moving. Do not place the Monitor in a built-in installation such as a bookcase or rack. Ventilation - required. When installing the Monitor on a table, be careful not to place the edge of its stand. This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor. - NOTES Do not place an outside antenna in the vicinity of overhead power lines other electric light or power circuits. - This may cause an electric shock. or There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. - This may cause an electric shock. NOTES Do not pull the cord but the when unplugging. plug - This may cause a fire. Ensure the power cord doesn't trail across any hot objects like a heater. - This may cause tric shock. a fire or an elec- Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose. - This may cause a fire an electric shock. or FirstepMonOvwCcBaSlmPu&df Others 5 Safety Instructions WARNING Do not placing anything containing liquid on top of the Monitor. - Using Do not insert any the exhaust vent. - This may cause a fire or could give an electric shock. object This may cause a fire an electric shock. or into could give WARNING Do not use water the Monitor while cleaning. - Cleanig This may cause damaged the Monitor or could give an electric shock. In case of smoke or strange smell from the Monitor, switch it off ,unplug it from the wall outlet and contact your dealer or service center. - This may cause a fire an electric shock. or could give WARNING Do not attempt to service the Monitor yourself. Contact your dealer or service center. Others 6 - This may cause damaged the Monitor or could give an electric shock. During unplug a lightning thunder, the Monitor from the wall outlet and don't touch an antenna cable. - This may cause damaged the Monitor or could give an electric shock. WARNING Do not place heavy the Monitor. Dispose of used batteries carefully to protect a child from eating them. objects on - This may cause serious a child or adult. injury to - In case to see a Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen. that it eats them, take it doctor immediately. NOTES Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. - This may cause damaged the Monitor an electric shock. or could Contact the service center once a year to clean the internal part of the Monitor. - Accumulated dust can cause mechanical failure. give NOTES The distance between eyes and the screen should be about5~7timesaslongas diagonal length of the screen. - If not, eyes will strain. Unplug the Monitor from the wall outlet when it is left unattended and unused for long periods of time. - Accumulated dust may cause fire or an electric shock from deterioration or electric leakage. a Only use teries. - the specified bat- This make cause damaged the Monitor or could give an electric shock. FirstepMonOvwCcBaSlmPu&df Others 7 Controls of the Monitor <Front Panel Controls> ON/OFF INPUT ON/OFF SELECT Main power button Remote control sensor INPUT SELECT VOLUME Power standby indicator Illuminates red in standby mode. Illuminates green when the Monitor is turned on. Sub power button INPUT SELECT button VOLUME (F,G) buttons 8 VOLUME Back Panel EXTERNAL SPEAKER R (+)() () AV INPUT S-VIDEO (8Ω) L (+) RL AUDIO (MONO) VIDEO COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) RGB-PC SPEAKER(8Ω) AV INPUT AUDIO L (MONO) VIDEO (+) RLR () () (+) EXTERNAL SPEAKER (8 ohm output) (DVD/DTV INPUT) S-VIDEO Y AUDIO INPUT RS-232C AC INPUT AUDIO RL COMPONENT(480i/480p/720p/1080i) EXTERNAL INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT (480p/720p/1080i) YP PB R RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (480p/720p/1080i) AUDIO INPUT RS-232C AC INPUT RL R B PP RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (480p/720p/1080i) / AUDIO INPUT/ RS-232C jacks A/V INPUT / S-VIDEO/ COMPONENT (480i/480p/720p/1080i) DVD/DTV INPUT jacks POWER INPUT SOCKET This Monitor operates on an AC mains supply, the voltage is as indicated as inside back cover of this manual. Never apply DC power to the Monitor. 9 FirstepMonOvwCcBaSlmPu&df Others Accessories POWER SLEEP INPUT SELECT APC DASP ARC STILL PIP /TWIN PCTURE PIPINPUT POSITION MENU VOL POWER REW MUTE OK STOP PLAY VOL P/STILL FF REC D-sub 15 pin cable Power cord 1.5V LG TV 1.5V AS mark Owner's Manual Optional - - Extras AP-42WA20M series (Tilt 10 Alkaline batteries Optional extras can be changed or modified optional extras can be added. Contract your dealer for buying these items. wall Remote control handset mounting bracket) for quality improvement without any notification AP-42WA10 series (Wall mounting bracket) new Optional - - Extras Optional extras can be changed or modified optional extras can be added. Contract your dealer for buying these items. for quality improvement without any notification AP-42CA10 series AP-42FA10 series (Ceiling mounting bracket) (Floor type stand) AP-42DA10 series AP-42SA10 series (Desktop stand) (Speakers) AP-42SA10D series AP-42SA10F series (Speaker stand) (Floor type speaker stand) Video cables new FirstepMonOvwCcBaSlmPu&df Others Audio cables 11 Controls of the Remote Control - When using the remote control aim it at the remote control sensor on the Monitor. POWER POWER SLEEP (Refer to p.34) APC (Refer to p.35) ARC (Refer to p.45) SLEEP INPUT SELECT APC DASP ARC STILL PIP PIP (Refer to p.28) PIP INPUT (Refer to p.29) / TWIN PICTURE PIP INPUT POSITION MENU MUTE MENU OK OK VOL POWER STOP P/STILL REW PLAY FF VOL VOLUME( , ) VCR BUTTONS controls a LG video cassette recorder. 12 REC INPUT SELECT button on the remote control INPUT SELECT Each press of this button DASP (Refer to p.39) STILL (Refer to p.41) changes the mode as shown below. VIDEO S-VIDEO RGB COMPONENT No function POSITION (Refer to p.29) MUTE switches the sound on or off. / selects a menu item. Using the Installing remote control batteries ? Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match "+" with "+", and match "-" with "-". ? Others Install two 1.5V "AAA" alkaline batteries. Don't mix used batteries with new FirstepMonOvwCcBaSlmPu&df batteries. 13 Monitor Installation - The Monitor type, can be installed in various ways such as wall mounting type, desktop etc.. Wall Mount Installation ? The monitor can be installed on the wall (For further information, refer to the Installation and Setup Guide'.) ? Speakers are optional, as shown above. optional '(Tilt) and shown for illustration wall mounting bracket only. Tips ? Install this monitor only in a location where adequate ventilation is available. a. ( Wall mount minimum allowable clearances for adequate ventilation 4inch ) 4inch 4inch 4inch 14 1.18inch Desktop Pedestal Installation ? ? The Monitor can be installed on a desk as shown above. (For further information, refer to the optional 'Desktop Stand Installation and Speakers shown are optional, and shown for illustration only. Setup Guide'.) b. ( 4inch Pedestal mount minimum allowable clearances for adequate ventilation ) 4inch 1.18inch FirstepMonOvwCcBaSlmPu&df Others 4inch 2.36inch 15 VCR - Setup As shown below, when connecting the Monitor to a VCR, match the colors of AV input jacks on the Monitor with the output jacks on the VCR: Video = yellow, Audio (Left) = white, Audio (Right) - - - = red. If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor. If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved, compared to connecting a regular VCR to the Video input. Avoid having a fixed image remain on the screen for a long period of time. A frozen still picture from a VCR (or if a CH label is displayed) displayed on the screen for prolonged periods will result in an image ghost remaining even when you change the image. Avoid prolonged display of a still image. S-VIDEO OUT (R) AUDIO (L) VIDEO IN < Back panel of VCR > Tips ? 16 To avoid picture noise (interference), leave between the VCR and monitor. an adequate distance (20 inches or more) AV INPUT EXTERNAL SPEAKER (+) R () () S-VIDEO (8Ω) L (+) RLVIDEO AUDIO (MONO) COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) COMPONENT(480i/480p/720p/1080i) EXTERNAL SPEAKER(8Ω) AV INPUT AUDIO L (+) RLR () () (+) S-VIDEO (MONO) VIDEO INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT (480p/720p/1080i) AUDIO INPUT AC INPUT RS-232C RL AUDIO RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (DVD/DTV INPUT) Y RGB-PC R YP PB (480p/720p/1080i) AUDIO INPUT RS-232C AC INPUT RL R PP B < Back panel of the Monitor > To watch VCR INPUT SELECT 1 2 Press INPUT SELECT button on the remote control and select VIDEO. (When connecting S-VIDEO.) with S-Video, select the FirstepMonOvwCcBaSlmPu&df Others Insert a video tape into the VCR and press the PLAY button on the VCR. See VCR owner's manual. 17 Cable TV - Setup subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming without a TV tuner or cable TV converter box. After AV INPUT EXTERNALSPEAKER R (+)() EXTERNAL (+) AV INPUT SPEAKER(8Ω) RL () () (+) L S-VIDEO R AUDIO L (MONO) VIDEO S-VIDEO COMPONENT (8Ω) () (+) RL AUDIO MONO) (480i/480p/720p/1080i) (DVD/DTV INPUT) YP PB VIDEO RGB-PC INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT (480p/720p/1080i) R AUDIOINPUT COMPONENT(480i/480p/720p/1080i) (DVD/DTV INPUT) PP B Y < RS-232C AC INPUT RL AUDIO RGB-PC INPUT (VGA/SVGA/XGA) (480p/720p/1080i) RGB-DTV INPUT Monitor back panel (AUDIOL)VIDO < TV VCR RF AUDIO INPUT RS-232C RL R > Cable box > Cable To watch cable TV Press INPUT SELECT button 1 on the INPUT SELECT remote control and select VIDEO source. Tune to cable service 2 using provided channels the cable box. Tips ? 18 For further information regarding cable TV service, contact your local cable TV service provider(s). External AV Source - Setup As shown below, when connecting the Monitor to an external source, match the colors of AV input jacks on the Monitor with the output jacks on the audio/video equipment: Video = yel- low, Audio (Left) = white, Audio (Right) AV INPUT EXTERNAL SPEAKER R (+)() S-VIDEO (8Ω) () L (+) RL AUDO (MONO) VIDEO COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) = RGB-PC red. INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT(480p/720p/1080i) AUDIOINPUT COMPONENT(480i/480p/720p/1080i) EXTERNAL (+) SPEAKER(8Ω) AV INPUT S-VIDEO RLR AUDIO L (MONO) VIDEO () () (+) AC INPUT RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (DVD/DTV INPUT) Y RS-232C AUDO RL YP PB R (480p/720p/1080i) R PP B <Back panel AUDIO INPUT RS-232C RL of the Monitor> Camcorder AUDIO VIO Video game set DDR To watch external AV 1 2 Press INPUT SELECT button on source the INPUT SELECT remote control of the monitor to select VIDEO. Operate the FirstepMonOvwCcBaSlmPu&df Others corresponding external equipequipment operating ment. See external guide. 19 DVD Setup How to connect ? DVD a (digital video disk Connect DVD video inputs to Y, PB, PR of COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) and audio inputs to Audio jacks of AV INPUT. EXTERNALSPEAKER R (+)() AV INPUT S-VDEO (8Ω) () L (+) RL AUDIO (MONO) VIDEO COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) RGB-PC INPUT(VGA/SVGA/XGA/SXGA) (480p/720p/1080i) RGB-DTV INPUT YP PB R AUDOINPUT RS-232C (+) SPEAKER(8Ω) RL () () (+) AV INPUT R AUDIO L (MONO) VIDEO RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (DVD/DTV INPUT) S-VIDEO AC INPUT RL AUDO COMPONENT(480i/480p/720p/1080i) EXTERNAL (480p/720p/1080i) R PP B Y (R) < How to ? AUDIO (L) Back B panel of a DVD AUDIO INPUT panel of the Monitor> R player> use Turn on the DVD player, and insert a DVD. Press INPUT SELECT button on the remote control of the monitor to select COMPONENT. Use the DVD player according to its owner's manual. ? Component Input ports Connect DVD player jacks to Monitor Component input jacks as indicated below. Component input jacks on Video the Monitor output jacks of DVD 20 RS-232C RL <Back ? player) player YPBPR Y Y Y Y Pb B-Y Cb PB Pr R-Y Cr PR DTV - - Setup To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX. You can select only the 16:9 picture format in DTV 720p/1080i mode. How to connect ? user-supplied Digital Set-top a Box You can use either the Monitor's COMPONENT (Y, PB, PR) inputs or the single RGB-DTV INPUT for video connections, depending on your Set Top Box connectors. Then, make the corresponding Audio connections. See the diagram below for either set up. AV INPUT EXTERNAL SPEAKER R (+)() S-VIDEO COMPONENT (8Ω) () L (+) RL AUDIO (MONO) (480i/480p/720p/1080i) (DVD/DTV INPUT) RGB-PC INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT(480p/720p/1080i) YP PB R VIDEO AUDIOINPUT COMPONENT(480i/480p/720p/1080i) EXTERNAL (+) SPEAKER(8Ω) RL () () AV INPUT R AUDIO L (MONO) VIDEO (+) Y AC INPUT RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (DVD/DTV INPUT) S-VIDEO RS-232C RL AUDO (480p/720p/1080i) R PP B RS-232C AUDIO INPUT RL <Back panel of the Monitor> or (R) AUDIO (L) B < How to ? Turn on (Refer ? Back panel R of a (R) AUDIO (L) DTV OUTPUT digital SET-TOP BOX> use the Others digital SET-TOP BOX. digital SET-TOP BOX.) the remote control to select COMPONENT to the owner's manual for the Press INPUT SELECT button on or FirstepMonOvwCcBaSlmPu&df RGB. 21 PC - See your Setup computer's image the monitor. on How to connect Make the connections shown in the illustration below. Set the computer video output to SXGA (1280x1024) or lower resolution. (If the video output of the PC is not compatible with the Monitor, no picture will appear on the Monitor. See page 23.) As shown below, connect the video output of the PC to the Monitor RGB-PC INPUT(VGA/SVGA/XGA) RGB-DTV INPUT(480p/720p/1080i). Connect the audio out from the PC to the Audio jacks on the Monitor. (Audio cables not included with the Monitor) If available, adjust PC sound to your preference. To setup this monitor in your PC Windows environment, select Normal, Standard or Default monitor. This monitor does not support Plug and Play function. ? ? ? ? ? AV INPUT EXTERNAL R (+)() EXTERNAL (+) SPEAKER(8Ω) RL () () (+) AV INPUT () L (+) S-VIDEO R AUDIO L (MONO) VIDEO Monitor back How to S-VIDEO SPEAKER(8Ω) RL AUDO (MONO) VIDEO COMPONENT (480i/480p/720p/1080) (DVD/DTV INPUT) RGB-PC INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT (480p/720p/1080i) COMPONENT(480i/480p/720p/1080i) (DVD/DTV INPUT) Y RS-232C AUDIOINPUT AC INPUT RL AUDIO YP PB R RGB-PC INPUT (VGA/SVGA/XGA) (480p/720p/1080i) RGB-DTV INPUT R PP B AUDIO INPUT RS-232C RL panel use ? ? On the remote control Press POWER button on the PC and press ON/OFF button the Monitor. After this press button on the Monitor or press POWER button on the remote control. Press INPUT SELECT button on the remote control to select RGB. Set the resolution of PC to XGA (1024x768) or lower. on INPUT SELECT ? (Refer to page 23.) Tips ? Avoid even 22 prolonged display of a still image, change the image. after you as it may cause a permanent image to remain Displayable Resolution 640x350 640x400 640x480 800x600 832x624 1024x768 Monitor Specification Horizontal Vertical Frequency (KHz) Frequency (Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 45.913 90.03 53.011 100.04 64.062 120.00 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 56.000 90.00 64.016 100.00 49.725 74.55 48.363 60.00 56.476 70.06 60.023 75.02 68.677 84.99 Tips ? Synchronization input form : FirstepMonOvwCcBaSlmPu&df Others separate 23 PC Mode Feature Check - - - Select RGB first, see page 13. Make sure the PC and monitor are both turned Use the monitor's remote control to make MENU (Overview) on. adjustments. 1 Press the MENU button to show a menu on screen. 2 Press the D / E button to select a menu. ? Each press will cycle through the different menus as shown below. PICTURE APC G DRP G CONTRAST 85G BRIGHTNESS 50G COLOR 50G TINT 0G SHARPNESS D MOVE E GNEXT 50G AEXIT <Picture menu> SOUND DASP G AVL G TREBLE 50G BASS 50G BALANCE D MOVE E GNEXT 0G AEXIT <Sound menu> SPECIAL D E LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G MOVE GNEXT AEXIT <Special VOL VOL 243 menu> PresstheGbuttonandthenpresstheD/EorF/G buttons to select ? a feature you want to Press the OK button to exit menus. use. PC Mode Auto - Adjustments FirstepMonOvw adjustment Automatically adjusts picture position and eliminates any image shaking. READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU Press the D / E button to select SCREEN and then press the G button. 1 VOL Press the D / E button to select AUTO.CONFIG. and then press the G button. 2 Conectis VOL SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G AUTO.CONFIG. G V-POSITION G H-POSITION G PHASE G RESET G BasicopertnSlmPu&df GTOSET GTOSET VOL When AUTO.CONFIG. has finished, "OK" will be shown on screen. If the position of the image is incorrect, try Auto adjustment again. ? ? If picture needs to be adjusted more after Auto adjustment, you manually adjust the image position and PHASE. 3 can Others Tips ? If the image adjustment. is still not correct, your Monitor is functioning properly but needs further 25 PC Mode Adjusting - Only adjust Adjustments horizontal / vertical V-POSITION and H-POSITION in DTV or position manually component 480p/720p/1080i. READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. Ti MENU 1 VOL Press the D / E button to select SCREEN and then press the G button. SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G GTOSET VOL 2 Press the D / E button to select V-POSITION H-POSITION and then press the G button. or AUTO.CONFIG. VOL 3 G G PHASE G RESET G 0 Press the F / G buttons to adjust until you get desired horizontal vertical position and then press the OK button to remove menus. ? ? ? ? or The adjustment range of V-POSITION is -50 +50. The adjustment range of H-POSITION is -100 +100. Based on the input mode, the adjustment range of V-POSITION/H-POSITION may change. Based on the VGA card, the adjustment range of V-POSITION/H-POSITION may be out of -100 +100 after auto configure. Based on the input signal, the position of the picture may not change even though you have adjusted the horizontal or vertical position with this function. ~ ~ ~ ? OK VOL 26 G V-POSITION H-POSITION VOL Picture Phase ? ? Adjustments If the picture isn't clear after auto adjustment and especially if the adjust the picture phase manually. When watching PIP, the SCREEN menu option is not available. characters are still trembling, then READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU 1 VOL 2 Press the D / E button to select PHASE and then press the G button. VOL Press the F / G button to 3 ? The Conectis VOL Press the D / E button to select SCREEN and then press the G button. adjustment range adjust phase of PHASE is 0 SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G AUTO.CONFIG. G V-POSITION G H-POSITION G PHASE G RESET G GTOSET BasicopertnSlmPu&df 30 and then press the OK button. 63. ~ OK VOL VOL Initializing (Reset ? to FirstepMonOvw Others factory value) To initialize the adjusted value, select RESET with the D / E button and then press the G button. 27 Picture In Picture - (PIP) function PIP lets you view 2 different inputs (sources) on your monitor screen at the large, and the other source will show a smaller inset image. same time. One source will be - - - - - - - Select RGB before pressing PIP. only in the following resolutions; RGB-DTV (480p, 720p,1080i), COMPONENT (480p, 720p,1080i), RGB-PC 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz) When you select RGB or DTV for main picture in PIP, you can watch video, s-video or DVD for sub picture. Color of main picture may be different from PIP's in PIP mode. If input source for main picture is changed while in PIP mode, sub picture will disappear. When watching PIP, SCREEN option is not available in Special menu. With PIP active, not all picture formats can be used for the main/sub picture. input source This function works Watching PIP the PIP (Picture in Press the PIP button. ? Each time you press PIP PIP size as below. or F / G button, you PIP [L] PIP[S] PIP F PIP[S] G <Small PIP> PIP F PIP[L] <Large G PIP> PIPFOFFG <Off> 28 Picture) can change OFF the Selecting PIP INPUT the source FirstepMonOvw input signal Press the PIP INPUT button in PIP mode. Each time you press PIP INPUT button, you S-VIDEO and COMPONENT. ? VIDEO S-VIDEO COMPONENT PIP INPUT Moving F source VIDEO the Sub only toggle VIDEO, Conectis COMPONENT works in 480i mode. G BasicopertnSlmPu&df (inset) picture POSITION Press the POSITION button in PIP mode. ? Each press of the POSITION button will change the the sub picture on the screen as shown below. position of Others 29 Picture In Picture Selecting - - - PIP sound (PIP) function options To select main or sub (inset) sound only works with the following resolutions; RGB-DTV (480p, 720p, 1080i), COMPONENT (480p, 720p, 1080i), RGB-PC 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz) To use this function, connect PC/DTV video output to RGB-PC INPUT/RGB-DTV This function INPUT and connect PC/DTV audio - outputs to AUDIO INPUT. SOUND SELECT is always the main picture sound (SOUND[M]) regardless of prior sound choice. READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU 1 VOL Use the D / E buttons to select PIP and then press the G button. VOL 2 SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G Press the D / E button to select SOUND SELECT and then press the G button. VOL PIP G INPUT G SOUND SELECT G SOUND [M] POSITION G SOUND [S] PIP G Press the D / E buttons to select main 3 image sound (SOUND [M]) or PIP (inset image) sound (SOUND [S]) and then press the OK button. ? Each time you press between SOUND [M] D / E or button, you toggle SOUND OK 30 [S]. INPUT G SOUND SELECT G SOUND [M] POSITION G SOUND [S] GTOSET Turning - When using Turning on control, aim it at its the Monitor just Connect power cord 1 sensor on the Monitor. after installation correctly. Press the main ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the or INPUT SELECT button on the Monitor or press the POWER or INPUT SELECT button on the remote control and then the Monitor will be turned on. 2 Turning 1 the remote the Monitor on on the Monitor (power cord is still If the Monitor is turned off with the connected) button on the Monitor Press the or INPUT SELECT button on the Monitor or press the POWER INPUT SELECT button on the remote control and then the Monitor will be turned on. or 2 3 If the Monitor is turned off with the ON/OFF button ? Press the main ON/OFF button on on the Monitor to turn the Monitor on the Monitor. If the Monitor is turned off with the remote control and also the ON/OFF button on the Monitor ? Press the main ON/OFF button on the Monitor and then press the or INPUT SELECT button on the Monitor or press the POWER or INPUT SELECT button on the remote control and then the Monitor will be turned Tips Adjusting volume level The volume(G) button increases on. Others ? the level of sound. the sound and the volume(F) FirstepMonOvwCcBaSlmPu&df button reduces 31 Selecting language for the menus READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU 1 VOL Press the D / E button to select LANGUAGE and then press the G button. SPECIAL LANGUAGE G 한국어 ARC G ENGLISH SCREEN G ESPANOL TRANSPARENCY G PORTUGUES PIP G SET ID G COLOR TEMP. G FRANCAIS VOL 2 3 Press the D / E button to select the desired language. Press the OK button to exit. OK 32 SPECIAL LANGUAGE G 한국어 ARC G ENGLISH SCREEN G ESPANOL TRANSPARENCY G PORTUGUES PIP G SET ID G COLOR TEMP. G FRANCAIS features Checking - - Use the remote control to make Select VIDEO input 1 MENU 2 adjustments. source Press the MENU button. Press the D / E button. ? Each press will the cycle through menus shown below. PICTURE APC G DRP G CONTRAST 100 50G COLOR 50G TINT 0G SHARPNESS D MOVE E G BRIGHTNESS GNEXT 50G AEXIT <Picture menu> SOUND DASP G AVL G TREBLE 50G BASS 50G BALANCE D MOVE E GNEXT 0G AEXIT <Sound menu> SPECIAL D E LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G MOVE GNEXT AEXIT <Special menu> a feature to adjust, andthenpresstheD/EorF/Gbuttonsto adjust the selected item. Press the G button to select VOL VOL 3 ? FirstepMonOvwCcBaSlmPu&df Others Press the OK button to exit. 33 Setting Sleep Timer Sleep Timer turns the SLEEP Monitor off after a preset time Press the SLEEP button to set sleep time. Each time you press SLEEP button, the next preset setting time is changed as follows: F---G F10G F20G F30G F120G F90G F60G F240G F180G SLEEP F30 G To release sleep time setting, press the SLEEP or F / G button repeatedly to select F G. ?' SLEEP 1' will be displayed one minute before the Monitor is due to switch off. ? --- Tips ? ? When the sleep time you want is displayed on the screen, don't press the SLEEP button. After 20 seconds, the screen display disappears and sleep time is set. To check remaining sleep time after setting, press the SLEEP or OK button just ? 34 once. If you turn the Monitor off after setting the sleep timer, the The sleep timer will then have to be set again. setting is erased. Auto control picture Use APC to set the Monitor for the best - APC is not available in RGB or picture appearance PIP mode. APC (Auto Picture Control) APC 1 2 Press the APC button. Press the APC or F / G buttons to select your desired picture condition. APC ? CLEAR G Each press of F / G buttons shown below. CLEAR ? F changes SOFT the screen display as USER You can also select CLEAR, SOFT or USER in the PICTURE menu. User refers to adjustments you made to the picture menu items. See next page. FirstepMonOvwCcBaSlmPu&df Others 35 Adjusting picture appearance - PIP inset setting is not adjustable. READY Press the MENU button and then press the D / E button to select PICTURE menu. Press the G button. MENU VOL the contrast. Press the D / E button to select CONTRAST and then press the G button. Example : Changing 1 PICTURE APC G DRP CONTRAST G 100 50G COLOR 50G TINT SHARPNESS 0G 50G VOL 2 Use the F / G buttons to make approand then press the OK button. priate adjustments ? Press the D / E buttons to select other items. PICTURE APC DRP ? Adjust BRIGHTNESS, COLOR, SHARPNESS in the 36 OK VOL same way. TINT and G G CONTRAST 70G BRIGHTNESS 50G COLOR 50G TINT SHARPNESS VOL G BRIGHTNESS 0G 50G DRP DRP - (Digital Reality Picture) improves image outlines in dark screens. This function works in video, component 480i mode. READY Press the MENU button and then press the D / E button to select PICTURE menu. Press the G button. MENU 1 VOL Press the D / E button to select DRP and then press the G button. PICTURE APC G DRP CONTRAST 100 G CLEAR G SOFT BRIGHTNESS 50G COLOR 50G TINT SHARPNESS 0G 50G VOL 2 Press the D / E button to select CLEAR or SOFT. PICTURE APC CONTRAST 100 G CLEAR G SOFT BRIGHTNESS 50G COLOR 50G TINT SHARPNESS 3 G DRP 0G 50G Press the OK button to exit. OK FirstepMonOvwCcBaSlmPu&df Others 37 Adjusting Manual sound setting READY Press the MENU button and then press the D / E button to select SOUND menu. Press the G button. MENU 1 VOL treble Use the D / E buttons to select TREBLE and then press the G button. Example : Adjustment SOUND DASP G AVL G TREBLE 50 BASS 50G BALANCE G 0G VOL 2 Use the F / G buttons to make appropriadjustment and then press the OK button to exit. ate ? Press the D / E buttons to select other VOL ? 38 Adjust VOL options. OK BASS and BALANCE in the same way. SOUND DASP AVL G G TREBLE 70G BASS 50G BALANCE 0G Auto Sound Control DASP ? (Digital Auto Sound Processing) This function lets you enjoy the best sound without any manual adjustment because the Monitor automatically selects the appropriate audio tone levels based on the program content. DASP 1 Press the DASP button. 2 Press the DASP or F / G buttons to select a sound setup. DASP ? FUSERG Each press of DASP or F / G buttons display as shown below. FLAT SPORTS USER ? changes the screen CINEMA MUSIC You can also select FLAT, SPORTS, CINEMA, MUSIC USER in the SOUND menu. or FirstepMonOvwCcBaSlmPu&df Others 39 AVL (Auto Volume Leveler) This feature maintains an equal volume level; even if you change channels. READY Press the MENU button and then press the D / E button to select SOUND menu. Press the G button. MENU 1 VOL Press the D / E button to select AVL and then press the G button. SOUND DASP AVL G G TREBLE 50G BASS 50G BALANCE ON OFF 0G VOL 2 PresstheD/EbuttontoselectONor OFF. SOUND DASP AVL 3 40 OK G 50G BASS 50G BALANCE Press the OK button to exit. G TREBLE 0G ON OFF Using Still - - This feature isn't available for RGB-PC Use with A/V, COMPONENT, STILL 1 or input function source. RGB-DTV video inputs. Press the STILL button. ? ? ? The image displayed is frozen(still). The sub picture is stilled in PIP mode. In PIP mode, the sub (inset) picture is frozen. <Moving image> <Still 2 To return to normal image> viewing, press the STILL button again. Tips ? ? If still picture is on the screen for more than 5 minutes, the image becomes dark. If another function is activated, normal brightness of the screen is restored. This is a protective feature designed to reduce a ghost image burning into the monitor. FirstepMonOvwCcBaSlmPu&df Others 41 Using - - This function works Use this option only if there the options screen in the video mode. are a trembling or instability of a video tape on screen during viewing the video. READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU VOL Use the D / E button to select SCREEN and then press the G button. 1 VOL 2 Use the D / E buttons to select TV ? ? Select the VCR option if watching Select the TV option for other equipment.(Except VCR) ? Each time you press the D between TV and VCR. / E 42 Press the OK button to exit. OK VCR. VCR. button you VOL 3 a or toggle SPECIAL LANGUAGE G ARC G SCREEN G TV TRANSPARENCY G VCR PIP G SET ID G COLOR TEMP. G SPECIAL LANGUAGE G ARC G SCREEN G TV TRANSPARENCY G VCR PIP G SET ID G COLOR TEMP. G Adjusting OSD Transparency To make the menus clear or opaque READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU 1 VOL Press the D / E button to select TRANSPARENCY and then press the G button. SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G 3 VOL 2 Press the F / G buttons to transparency. ? The adjustment range of TRANSPARENCY is1~4. VOL 3 adjust OSD SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G 3 VOL Press the OK button to exit. OK FirstepMonOvwCcBaSlmPu&df Others 43 Adjusting - - color temperature also affect the color temperature of other input sources. Readjust color temperature for PC input (RGB) if necessary. To initialize adjusted value, select '0' in RED, GREEN and BLUE. Adjustments READY Press the MENU button and then press the D / E button to select SPECIAL menu. Press the G button. MENU 1 VOL Press the D / E button to select COLOR TEMP. and then press the G button. SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G GTOSET VOL 2 Press the D / E button to select RED and then press the G button. (to adjust RED setting) RED G GREEN G BLUE G 0 VOL ? 3 Adjust GREEN and BLUE in the same Use the F / G button to make press the OK button. way. appropriate adjustments OK VOL ? 44 The VOL adjustment range of RED, GREEN and BLUE is -5 +5. ~ and then Setting picture format - With the RGB-PC - With the RGB-DTV - If 4:3 mode is input, you can select either 16:9 or 4:3 screen aspect ratios. (720p, 1080i) input, you can select only 16:9 screen aspect ratios. used for a long time, the outline of the image may remain on the screen after to the 16:9 screen. - you change Don't display 4:3 ARC picture format for more than 10 hours continuously. Press the ARC button to select format. ? Each time you press ARC select 16:9, 4:3 or ZOOM or F a desired / G buttons, you picture can alternatively. ARCF16:9G <16:9> ARCF4:3G <4:3> ARCFZOOMG <Zoom> ? You can also select 16:9, 4:3 or ZOOM in the SPECIAL menu. FirstepMonOvwCcBaSlmPu&df Others 45 External Control Device - Connect the RS-232C input jack to an external control device and control the Monitor's functions externally. Adjustments (such as a computer or an A/V control system) How to connect external control ? ? ? Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. RS-232C connection cables are not supplied with the Monitor. The Monitor remote control and front panel controls (except main power) will not be functional if the Monitor is controlled by a PC computer or other external device. AV INPUT EXTERNAL SPEAKER R (+)() () S-VIDEO (8Ω) L (+) RL AUDO (MONO) COMPONENT (480i/480p/720p/1080i) (DVD/DTV INPUT) SPEAKER(8Ω) AV INPUT AUDIO L (MONO) VIDEO (+) RLR () () (+) Y INPUT(VGA/SVGA/XGA/SXGA) INPUT(480p/720p/1080i) PP B AUDIO INPUT RS-232C AC INPUT AUDIO RL RGB-PC INPUT (VGA/SVGA/XGA) RGB-DTV INPUT (DVD/DTV INPUT) S-VIDEO RGB-PC RGB-DTV YP PB R VDEO COMPONENT(480i/480p/720p/1080i) EXTERNAL R Monitor Rear Connections Panel 46 equipment (480p/720p/1080i) AUDIO INPUT RL RS-232C AC INPUT Type of connector : D-Sub 9-pin male 1 No. Pin 1 No connection name 2 RXD 3 TXD 5 (Receive data) (Transmit data) (DTE side ready) 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 No Connection (DCE side ready) (Ready to send) (Clear to send) 9 Pin No.4 and Pin No.6 must be connected 6 on monitor side. * Use a null modem cable. Wire the 7-Wire cable so that each pair of data lines cross between the two devices. These data line pairs (Receive data) and TXD (Transmit data), DTR (DTE side ready) and DSR (DCE side ready), and RTS (Ready to send) and CTS (Clear to send). When using the 3-Wire cable connected to RXD, TXD and GND; Pin No. 4 (DTR) and Pin No. 6 (DSR) must be connected to the monitor. (The cable must be disconnected from the Monitor to be able to use the remote control and Monitor front panel controls.) With the RS-232 input connected, the Monitor cannot be controlled by both an external control device and the remote control at the same time. The Monitor can only be controlled by either the remote control or the are * RXD external control device. RS-232C configurations 7-wire (Standard 3-wire configuration (Not standard) configuration RS-232C cable) PC PDP PC PDP RXD 2 3 TXD RXD 2 3 TXD 3 2 RXD TXD 3 2 RXD GND 5 5 GND GND 5 5 GND TXD DTR 4 6 DSR DTR 4 4 DTR DSR 6 4 DTR DSR 6 6 DSR RTS 7 8 CTS RTS 7 7 RTS CTS 8 7 RTS CTS 8 8 CTS DB9 DB9 DB9 DB9 Control line 7-Wire Cable ? 3-Wire Cable Configuration The Monitor is available to switch between external adjustment and remote control adjustment using a control line. Note: If the control line is trolled by ? When using Configuration a 3-Wire cable configuration there is control line. The external control device must no put the Monitor into the high, the monitor is con- the external control device. If the control line is low, the Monitor is controlled remote control. by the Monitor's "change into remote control adjustment mode" (see page 53). The Monitor will then be able to be controlled by the remote control. If the Monitor is turned back on, it will revert back to external device control. 47 FirstepMonOvwCcBaSlmPu&df Others External Control Device Adjustments SET ID ? Use this function to specify a monitor ID number. READY Press the MENU button and then press the D / E button to select the SPECIAL menu. Press the G button. MENU 1 VOL UsetheD/EbuttonstoselectSETIDand then press the G button. SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID COLOR TEMP. G 1 G VOL 2 UsetheF/GbuttontoadjustSETID choose the desired monitor ID number. ? The VOL 48 adjustment range VOL of SET ID is 1 OK 99. to SPECIAL LANGUAGE G ARC G SCREEN G TRANSPARENCY G PIP G SET ID G COLOR TEMP. G ~ 1 - The RS-232C is used to control the Monitor's functions input jack Communication Parameters ? Baud rate ? Data : 2400 length Parity : None ?Stopbit:1bit Protocol [Command][ ][Set ID][ ][Data][Cr] * Communication code Receiving Transmission bps (UART) ? ? external control device. an Transmission / 8 bits : using : ASCII code * [Command] [Set ID] : To control PDP set. : You can adjust the set ID to choose desired monitor ID number in * If the command interval is seconds, only Command Be careful when using interrupted for more 1 will be recognized. than 4 See page 48. is1~99. menu. the power command. When selecting Set ID special Adjustment range '0', every connected PDP set is controlled. * [DATA] : To transmit command data. Transmit 'FF' data to read status of command. * [Cr] : Carriage Return ASCII code '0x0D' *[] Command Reference List : ASCII code 'space (0x20)' OK Acknowledgement [Set ID][:][OK][x][Data][x] NAME COMMAND 01. Power DATA RANGE p 0~1 i 0~3 r 0~2 04. Screen mute m 0~1 05. Volume mute w 0~1 06. Volume control v 0~64 07. Contrast k 0~64 08. b 0~64 c 0~64 02. 03. Input Select Aspect Ratio Brightness 09. Color * on 10. Tint t 0~64 11. s 0~64 12. OSD select d 0~1 13. Abnormal state a 0~1 14. PIP z 0~3 e 0~1 u 0~1 x 0~3 j 0~1 15. PIP input select 16. PIP sound select 17. PIP position 18. remote control adjustment this format when (acknowledgement) based receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Set ID][:][NG][x] * Sharpness The Monitor transmits ACK The Monitor transmits ACK on this format when non-viable functions (acknowledgement) based receiving abnormal data from or communication errors. mode FirstepMonOvwCcBaSlmPu&df Others 49 External Control Device 01. Power 03. (Command:p) You [p][ ][Set ID][ ][Data][Cr] : [r][ ][Set ID][ ][Data][Cr] Example : Power on Type:P31'0x0D' for set ID No.3. Data Acknowledgement [Set ID][:][OK][x][Data][x] Data 0 : In example : 0 : Wide 1 : Normal 2 : Full (16:9) (4:3) (Zoom) screen screen screen Acknowledgement Power Off [Set ID][:][OK][x][Data][x] 1:PowerOn * format. also can Transmission Power Off 1:PowerOn * (Command:r) screen adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Special menu. Transmission 0 Ratio Aspect G To adjust the G To control Power On/Off of the Monitor. Data Adjustments Data Monitor Acknowledges power on for set ID No.3. G To show Power On/Off. * 0 : Wide 1 : Normal 2 : Full screen screen the PC Using (16:9) (4:3) (Zoom) screen you select either 16:9 input, or 4:3 screen aspect ratio. Transmission * [p][ ][Set ID][ ][FF][Cr] the DTV Using 16:9 screen 720p/1080i input, you can only select aspect ratio. Acknowledgement [Set ID][:][OK][x][Data][x] 04. Screen mute Data G To select * 0 : Power Off 1 : Power On 2 : Power On 3 : Power On 4 : Power On (RGB) (Video) (Component) (S-Video) 02. presents Input [m][ ][Set ID][ ][Data][Cr] Data status about each function. You can 0 : Screen mute 1 : Screen mute off source on an 0 : Screen mute 1 : Screen mute off input source using the INPUT 05. Volume mute G To control volume You [i][ ][Set ID][ ][Data][Cr] :RGB 1 : 2 : 3 : AV (Video) Component S-AV (S-Video) [Set ID][:][OK][x][Data][x] 0:RGB 1 50 : 2 : 3 : AV (Video) Component S-AV (S-Video) (Picture off) (Picture on) can also (Command:w) mute on/off. adjust mute using the MUTE button remote control. Transmission [w][ ][Set ID][ ][Data][Cr] Data Acknowledgement Data on for the Monitor. the Monitor's remote control. Transmission 0 (Picture off) (Picture on) Acknowledgement Data (Command:i) also select SELECT button Data on [Set ID][:][OK][x][Data][x] select G To select input mute on/off. Transmission In like manner, if other functions transmit 'FF' data based on this format, Acknowledgement data feed back screen (Command:m) 0 : Volume mute 1 : Volume mute off on (Volume off) (Volume on) Acknowledgement [Set ID][:][OK][x][Data][x] Data 0 : Volume mute 1 : Volume mute off on (Volume off) (Volume on) on 06. Volume control (Command:v) 09. Color G To adjust the G To adjust volume. You on also can (Command:c) adjust You volume with the volume buttons also can screen adjust color. color in the Picture Transmission remote control. Transmission [c][ ][Set ID][ ][Data][Cr] [v][ ][Set ID][ ][Data][Cr] Data Data Refer to 'Real data Min:0~Max:64 Refer to 'Real data * Min:0~Max:64 * menu. mapping' as shown below. mapping' as shown below. Acknowledgement [Set ID][:][OK][x][Data][x] Acknowledgement Data Min:0~Max:64 [Set ID][:][OK][x][Data][x] Data Min:0~Max:64 10. Tint 07. Contrast (Command:t) G To adjust the (Command:k) You also can screen adjust tint. tint in the Picture menu Transmission G To adjust You screen also can contrast. adjust contrast in the Picture menu. [t][ ][Set ID][ ][Data][Cr] Data Red:0~Green:64 Transmission [k][ ][Set ID][ ][Data][Cr] Data Refer to 'Real data mapping' as shown below. Acknowledgement [Set ID][:][OK][x][Data][x] Min:0~Max:64 * Refer to 'Real data * mapping' as shown below. Data Red:0~Green:64 Acknowledgement [Set ID][:][OK][x][Data][x] Data Min:0~Max:64 11. Sharpness (Command:s) G To adjust the You can also sharpness. adjust sharpness in screen the Picture menu Transmission 08. Brightness (Command:b) [s][ ][Set ID][ ][Data][Cr] Data G To adjust You also can brightness. adjust brightness * in the Picture menu. Transmission Refer to 'Real data mapping' as shown below. Acknowledgement Data * Min:0~Max:64 * Refer to 'Real data [Set ID][:][OK][x][Data][x] [b][ ][Set ID][ ][Data][Cr] Data Min:0~Max:64 screen mapping' as shown below. Min:0~Max:64 Real data 0 mapping :Step0 Acknowledgement [Set ID][:][OK][x][Data][x] Data Min:0~Max:64 A:Step10 F:Step15 10:Step16 64 : Step FirstepMonOvwCcBaSlmPu&df Others 100 51 External Control Device 12. OSD select (Command:d) 14. PIP PIP using the pip Special menu. Transmission [d][ ][Set ID][ ][Data][Cr] 0 :OSDoff 1 :OSDon [Set ID][:][OK][x][Data][x] * :OSDoff 1 :OSDon main can remote control power) are is set up to be controlled not by controls panel operable when the PC the Monitor 0 :PIPoff 1 : PIP 2 : PIP (small) (large) computer. PIP 0 :PIPoff 1 : PIP 2 : PIP (small) (large) following resolutions: (VGA) / 800x600(SVGA) (XGA) (only in vertical frequency 60Hz), Component 480p / 720p / 1080i. only works in the RGB PC 640x480 13. Abnormal state an in the [Set ID][:][OK][x][Data][x] Data * G To recognize also control or Acknowledgement The remote control and Monitor front (except on [z][ ][Set ID][ ][Data][Cr] Acknowledgement 0 button Transmission Data Data (Command:z) G To control PIP (Picture-in-Picture). You G To select OSD (On Screen Display) on/off. Data Adjustments / 1024x768 (Command:a) abnormal state. Transmission 15. PIP input [a][ ][Set ID][ ][FF][Cr] G To select input Acknowledgement You [Set ID][:][OK][x][Data][x] Data 0:OK 1 : the remote control for sub source or in the picture in PIP mode. using PIP input button on Special menu. Fan alarm [e][ ][Set ID][ ][Data][Cr] :ACdown Data * source also select can (Command:e) Transmission 2:5Vdown 3 select This function is "read only". 0 : AV 1 : COMPONENT 2 : S-AV (VIDEO) (S-VIDEO) Acknowledgement [Set ID][:][OK][x][Data][x] Data * 52 0 : AV 1 : COMPONENT 2 : S-AV (VIDEO) (S-VIDEO) COMPONENT source only works with 480i input signal. 16. PIP sound select G To select main You can special or sub 18. (Command:u) (inset) Change into Remote control adjustment mode (Command:j) sound for PIP. also select sound select in PIP on the G menu. To control the Monitor with the remote control while the cable is still connected. Transmission Transmission [u][ ][Set ID][ ][Data][Cr] Data [j][ ][Set ID][ ][Data][Cr] picture sound 1 : Sub picture sound Acknowledgement 0 : Main Data * 0 : Main 1 : Sub source Remote control adjustment mode [Set ID][:][OK][x][Data][x] picture sound picture sound COMPONENT : Acknowledgement [Set ID][:][OK][x][Data][x] Data 1 Data works in 480i only input signal. * 0 : PC 1 : Remote control If external "change Monitor adjustment equipment mode adjustment mode commands the Monitor to into remote control can only be adjustment mode", the adjusted by the remote control. To revert the Monitor control to external control device adjustment, 17. PIP turn the Monitor off and then on again. position (Command:x) G To select sub picture position for PIP. You can also adjust the sub picture position using the position button on the remote control or in PIP on the Special menu. Transmission [x][ ][Set ID][ ][Data][Cr] Data down 0 : Right 1 : Left down 2 : Left up 3 : on screen on screen on screen Right up on Acknowledgement screen [Set ID][:][OK][x][Data][x] Data down 0 : Right 1 : Left down 2 : Left up 3 : Right on screen on screen on screen up on screen FirstepMonOvwCcBaSlmPu&df Others 53 Troubleshooting No picture & ? Check whether the Monitor is turned ? Power cord inserted into wall outlet? check list on. No sound ? ? Press the VOLUME ? Sound muted? Press MUTE button. Picture OK & No sound ? The remote control ? doesn't work ? or or Poor color Poor picture ? ? Check to Install output from one of the speakers 54 ? button. see if the batteries new to are installed with the correct p.13) batteries. (Refer to p.13) Select COLOR in the PICTURE UME (G) button. (Refer to p.36) menu and press the VOL- Increase the distance between the Monitor and the VCR. Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen No (G) Check to see if there is any object between the Plasma Display and the remote control causing obstruction. polarities. (Refer ? No Plug another product's power cord into the wall outlet where the Monitor's power cord was plugged in. Adjust gets dark.) BALANCE in the SOUND menu. (Refer to p.38) Product specifications MP-42PZ15/A/B/G/K/S MP-42PZ15H/AH/BH/GH/KH/SH MODEL (inches / mm) 41.6 / 1056 Height (inches / mm) 25/635 Depth (inches / mm) 3.2/82 Width Weight (pounds Power / 72.1 / 32.7 kg) requirement AC110-240V 852 Resolution Color ? The specifications shown quality improvement. x 50/60Hz ~ 480 (Dot) 16,770,000 (256 steps of each R, G and B) above may be changed without prior notice for FirstepMonOvwCcBaSlmPu&df Others 55
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project