Adtran Total Access 612 Owner manual

Total Access 612/616/624 ATM Upgrade Procedure
Page 1 of 3
TECHNICAL SUPPORT NOTE
Total Access 612/616/624 ATM Upgrade Procedure
Introduction
As features are added to the TA612/616/624, software upgrades may be necessary. The
TA612/616/624 has flash memory allowing the software to be upgraded from a file provided by
ADTRAN. The current version of the software can be found in the "System Info" menu.
The software can be upgraded using HyperTerminal, or any terminal emulation package supporting the
XMODEM protocol. It can also be upgraded using TFTP and a TFTP server. Please proceed to the
appropriate section for further instruction.
If a terminal emulation package other than HyperTerminal is selected, please see the instructions
supplied with the package to set up an XMODEM connection.
Attention: This code is based off the D.01 development tree. The purpose is to convert D.01
configuration to D.04 configuration, so that when a user upgrades from D.01 code to D.04 code the
configuration will not be lost.
TO UPGRADE FROM D.01 TO D.04 WITHOUT LOSING
CONFIGURATION
Save the D.01 configuration either to a *.cfg file (under Config
Transfer) or to a text file using the terminal mode "download"
command. This is a safeguard only and is not necessary for
successful D.01 to D.04 upgrade. This file will be useful if ever the
need arises to go back to D.01 code.
Load (via TFTP or XMODEM) D.01.90 code. Unit will reset.
Load (via TFTP or XMODEM) D.04.xx code. You are now running
version D.04.xx
TO UPGRADE FROM D.01 TO D.04 WITH FACTORY DEFAULTS
If you don't care about saving your configuration, there is no need to load
the transition (D.01.90) code. Simply load D.04.xx code.
After the code has loaded, remove power from the unit. Make sure
you have a serial console session open and are connected to the
craft port.
Now plug the unit back in and press the "F" key as the unit powers
up. This will cause the unit to factory default all options.
Note: If, while running the transition code (D.01.90) you make any changes to the configuration, you
must RESET the IAD in order for those changes to be successfully migrated to D.04. Then you may
continue with the upgrade process and load D.04.xx.
Note: When upgrading from one D.04.xx firmware to another D.04.xx firmware, there is no need to use
the D.03.90 firmware. This will cause a loss of configuration.
http://kb.adtran.com/display/2/kb/articleContent.asp?aid=1321&n=&s=&fh=&link=
10/9/2007
Total Access 612/616/624 ATM Upgrade Procedure
Page 2 of 3
Using HyperTerminal to Upgrade Firmware:
1. Download the necessary upgrade files from the ADTRAN web site (www.adtran.com).
2. From the Start button choose Programs; then choose Accessories, then HyperTerminal.
3. When the Connection Description window appears, type in a connection name, select an
icon, and click OK.
4. In the Connect To window, select the COM port to which the TA612/616/624 is
connected in the Connect using field and click OK.
5. The COM port Properties window appears next. Change Bits per second to 9600, Data
bits =8, Parity = None, Stop bits = 1, Flow Control = None and click OK.
6. You are now connected.
7. Press Enter to get to the main menu.
8. In the TA612/616/624 menu, select the "System Utility" menu, then select "Upgrade
Firmware".
9. Change the "Transfer Method" to "XMODEM".
10. Select "Start Transfer" from the menu. The unit is now waiting for an upload from the
computer.
11. Click on "Transfer" then click "Send File..." in the HyperTerminal program.
12. Click Browse to locate the directory and file to download to the TA612/616/624.
13. Change the Protocol to XModem and click Send.
14. Once the download is complete, the unit will reset itself and continue operation.
TFTP Upgrade Method
1. Ensure that the ADTRAN Utilities CD-ROM has been installed on your computer.
2. Download the firmware upgrade file to your computer and save it to the "ADTNUTIL"
directory on your hard drive.
3. Start ADTRAN'S TFTP Server by selecting Start/Programs/ADTRAN Utilities/TFTP
Server from the Start menu.
4. Open a telnet session to the TA612/616/624. Select "System Utility" from the main menu
and then choose "Upgrade Firmware".
5. Change the "Transfer Method" to "TFTP". Enter the IP address of the computer running
ADTRAN'S TFTP Server in the "TFTP Host" field. Then enter the name of the firmware
file that was downloaded from the ADTRAN web site into the "Filename" field.
6. To begin the transfer, select "Start Transfer". Percentage complete will be shown on the
menu during the transfer.
7. Once the download is complete, the TA612/616/624 will reset.
If you experience any problems using your ADTRAN product, please contact ADTRAN Technical
Support.
DISCLAIMER
ADTRAN provides the foregoing application description solely for the reader's consideration
and study, and without any representation or suggestion that the foregoing application is or
may be free from claims of third parties for infringement of intellectual property rights,
http://kb.adtran.com/display/2/kb/articleContent.asp?aid=1321&n=&s=&fh=&link=
10/9/2007
Total Access 612/616/624 ATM Upgrade Procedure
Page 3 of 3
including but not limited to, direct and contributory infringement as well as for active
inducement to infringe. In addition, the reader's attention is drawn to the following
disclaimer with regard to the reader's use of the foregoing material in products and/or
systems. That is:
ADTRAN SPECIFICALLY DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL ADTRAN BE LIABLE FOR ANY LOSS
OR DAMAGE, AND FOR PERSONAL INJURY, INCLUDING BUT NOT LIMITED TO,
COMPENSATORY, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES.
http://kb.adtran.com/display/2/kb/articleContent.asp?aid=1321&n=&s=&fh=&link=
10/9/2007