Morphy Richards 47006 Cafe Rico pump Combi coffee maker with grinder Instruction


Add to my manuals
8 Pages

advertisement

Morphy Richards 47006 Cafe Rico pump Combi coffee maker with grinder Instruction | Manualzz
47008 rev4:x 13/11/2009 10:54 Page 1
Upon registration with Morphy Richards
(UK & ROI only)
Register online for your 2 year
guarantee. See back of this
instruction book for details.
(UK and Ireland customers only)
www.morphyrichards.co.uk
Mister Cappuccino
10 cup filter coffee maker
with heated frother
Please read and keep these instructions
Getting the best from your new coffee maker...
WARNING: Hot water and steam
Safety first
Caution must be used when handling hot water, coffee or steam
Run water through your machine before first use
It is important to run water through your coffee maker in order to rinse the machine.
You can also run water through to warm your coffee machine.
Descale as appropriate for the hardness of the water in
your area
It is important to descale as the performance of your coffee maker may be impaired
by limescale and other impurities in the water supply.
CM47008 MUK Rev 4
If you have a problem or complaint, please call our dedicated UK based helpline
before returning your product to the retailer from where it was purchased.
UK Helpline: 0844 871 0946
Replacement Parts: 0844 873 0712
Ireland Helpline: 1800 409 119
For details of other Morphy Richards products, please see our website:
47008 rev4:x 13/11/2009 10:54 Page 2
IMPORTANT
SAFETY
INSTRUCTIONS
•
The use of any electrical
appliance requires the following
common sense safety rules.
IMPORTANT: Damage to the
appliance!
•
Do not let the mains cable hang
over the edge of the worktop
where a child could reach it.
Do not let the cable run across an
open space e.g. between a low
socket and table.
Product safety
•
Never use warm or hot water to
fill the water tank.
•
Ensure the lid of the glass jug is
securely in place before pouring.
Take care to pour hot coffee
slowly and carefully without
tipping the glass jug too fast.
•
The mains cable should reach
from the socket to the base unit
without straining the connections.
•
Do not place the glass jug on the
hot plate unless the lid is in
position.
•
If the supply cable is damaged, it
must be replaced by the
manufacturer, it’s service agent or
similarly qualified persons in order
to avoid a hazard.
•
Do not fill above the capacity
mark of the water level gauge.
•
Do not use the glass jug or milk
frother jug in a microwave.
•
Milk should not be reheated, only
heat it when required.
Personal safety
farm houses;
•
Ensure the lid of the glass jug is
securely in place before pouring.
•
When heating milk, please use
stainless steel jug provided.
•
Take care to pour hot coffee
slowly and carefully without
tipping the glass jug too fast.
•
Do not fill milk jug above the MAX
mark.
•
It is not suitable for use in staff
kitchen areas in shops, offices
and other working environments.
•
Do not fill above the capacity
mark of the water level gauge
marked on the jug.
Do not adjust the coffee strength
once brewing is in process.
•
Do not overfill the water tank.
•
Always locate your appliance
away from the edge of the
worktop.
•
Do not touch metal parts until the
unit has cooled.
•
The glass jug gets hot while the
machine is in use. Always use
with care.
•
•
Remove all the packaging and
retain for future reference.
•
Make sure the mains lead does
not touch the hot parts of the
machine.
•
Ensure the coffee maker is used
on a firm, flat surface.
This appliance is not intended for
use by persons (including
children) with reduced physical,
sensory or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning the use of
the appliance by a person
responsible for their safety.
•
Do not wind the mains lead
around the hot appliance or store
the appliance until it has fully
cooled down.
•
Do not move when switched on.
Do not open the reservoir lid
whilst it is brewing.
Children
Treating scalds
bed and breakfast type
environments.
•
Do not use the coffee maker
outdoors or in near water.
•
Do not place the coffee maker on
a highly polished wooden surface
as damage may occur to the
surface.
•
2
Children should be supervised to
ensure that they do not play with
the appliance.
•
This appliance is intended to be
used in household and similar
applications such as:
by clients in hotels, motels
and other residential type
environments;
•
Do not let the cable run across a
cooker or other hot area which
might damage the cable.
In addition, we offer the following
safety advice.
•
Never allow children to use this
appliance.
•
WARNING : Danger to the
person!
Location
•
Mains cable
•
Primarily there is danger of injury
or death and secondly the danger
of damage to the appliance.
These are indicated in the text by
the following two conventions:
WARNING: Do not place the
coffee maker onto a metal tray
or metal surface whilst in use.
Do not place the coffee maker on
or near hot surfaces such as a
hot plate or radiant rings or near
a naked flame.
UK Helpline 0844 871 0946
•
•
Children do not understand the
dangers associated with
operating electrical appliances.
Replacement Parts 0844 873 0712
•
Run cold water over the affected
area immediately. Do not stop to
remove clothing, get medical help
quickly.
Ireland Helpline 1800 409 119
47008 rev4:x 13/11/2009 10:54 Page 3
Other safety
considerations
•
Caution: To prevent damage to
the appliance, do not use
alkaline cleaning agents when
cleaning. Use a soft cloth and
mild detergent.
•
Disconnect the coffee maker
from the mains supply when
filling, cleaning or not in use.
•
When unplugging, turn any
control to ‘off’, then remove plug
from the wall outlet.
ELECTRICAL
REQUIREMENTS
Keep the outside of the coffee
maker area clean and dry at all
times.
Check that the voltage on the
rating plate of your appliance
corresponds with your house
electricity supply which must be
A.C. (Alternating current).
•
•
•
•
•
FEATURES
⁄ Filter locating tab
¤ Removable permanent mesh
filter
‹ Removable filter holder with
locking tab
› Non drip valve
fi Milk frother on/off button
fl Milk frother attachment
‡ Milk frother hot plate
Do not touch hot surfaces.
Always use handles or knobs.
If the socket outlets in your home
are not suitable for the plug
supplied with this appliance the
plug should be removed and the
appropriate one fitted.
Do not immerse the coffee maker
itself in water and always ensure
the electrical connections are
kept dry.
WARNING: The plug removed
from the mains lead, if
severed, must be destroyed as
a plug with a bared flexible
cord is hazardous if engaged
into a live socket outlet.
Do not operate any appliance
with a damaged cord or plug or
after the appliance malfunctions
or has been damaged in any
manner. Ring the helpline number
for advice on examination and
repair.
Should the fuse in the 13 amp
plug require changing a 13 amp
BS1362 fuse must be fitted.
The use of attachments or tools
not recommended or sold by
Morphy Richards may cause fire,
electric shock or injury.
WARNING: This appliance
must be earthed.
· Milk frother hot plate on/off
switch with indicator
‚ Coffee hot plate on/off switch
with power & ready indicators
„ Coffee hot plate
‰ Water level indicator
 Hinged reservoir lid with
strength selector.
Ê Jug lid
Á Glass coffee jug with water
level indicator
Ë Measuring spoon
•
Do not use the coffee maker for
anything other than its intended
purpose.
È Milk frother jug
⁄
¤
Ê
Â
‹
Á
›
fi
Ë
fl
È
‰
„
‚
‡
·
For details of other Morphy Richards products, please see our website:
3
47008 rev4:x 13/11/2009 10:54 Page 4
A
OPERATING THE
APPLIANCE
Before use
5
Select the strength of coffee required
using the strength selector on the
reservoir lid C.
6
Slide the jug into the coffee maker,
ensuring it sits correctly on the hot
plate. The jug lid must be in place
during the brewing process,
otherwise the non-drip valve will not
open, causing the filter to flood.
7
Plug the filter coffee maker in at the
wall socket and push the coffee
on/off switch to ‘ON’ position. The
orange light will glow to show the
coffee maker is working.
8
Hot water will start to flow through
the coffee grounds and into the glass
jug as coffee.
9
When the filtering process is
complete, remove the glass jug from
your coffee maker and pour the
coffee into your cups.
Take your coffee maker out of the
box and remove the packaging.
Before using the appliance for the
first time, clean thoroughly by
operating two or three times with the
maximum volume of fresh water (10
cups) but without using coffee.
Rib
Locking tab
Wash the detachable parts of the
machine in warm soapy water.
Locating the filter
1
B
2
To remove the filter, slide the locking
tab on the removable filter holder to
the unlock position and lift both the
holder and mesh filter out to clean
(see cleaning) A.
To refit, place the removable filter
holder into the top of your coffee
maker, making sure the tab lines up
with the rib then slide the locking tab
to the lock position. Place the
permanent mesh filter inside the filter
holder by lining up the locating tab
with the groove in the filter holder as
shown.
Making coffee
1
Lift up the hinged reservoir lid.
2
Fill the water reservoir with the
required amount of water using the
water level indicator as a guide. Both
the jug and water level indicator are
marked in cups. Do not exceed the
maximum level on the water gauge
B.
C
3
4
4
UK Helpline 0844 871 0946
Spoon the required amount of
ground filter coffee into the mesh
filter, spreading it evenly. We suggest
one level measuring spoon for every
cup. Ensure the filter is sitting
properly in the filter holder.
10 The anti-drip valve will prevent any
remaining coffee dripping onto the
hot plate. Ensure that the jug is
replaced on the hot plate after
serving. While the coffee maker is
switched ON the hot plate will keep
the coffee warm.
11 Switch off the coffee maker when the
jug is empty or the coffee is no
longer required.
WARNING: The coffee maker and
hot plates are hot and remain hot
for some time after switching off.
12 Allow unit to cool.
13 Remove the permanent mesh filter
and empty the used coffee grounds.
Wash the filter immediately and dry
thoroughly. NOTE: THE MESH WILL
BECOME DISCOLOURED AFTER A
WHILE DUE TO THE STAINING
EFFECT OF COFFEE.
NOTE: It is normal for the green
ready light to go out and come back
on intermittently due to thermostatic
cycling.
Close the reservoir lid.
Replacement Parts 0844 873 0712
Ireland Helpline 1800 409 119
47008 rev4:x 13/11/2009 10:54 Page 5
Making a cappuccino
Cleaning
Prepare your machine as described
in the section ‘Making a coffee’. Use
your glass jug for measuring the
correct amount of water needed.
The milk frother blade can be wiped
clean still attached to the machine or
it can be removed for easy cleaning
by unscrewing the blade and shaft.
Wash carefully in hot soapy water.
Frothing milk
For quick cleaning just after use, fill
up the milk jug with hot water and
run the frother for 30-50 seconds;
repeat the process twice.
It is advised to start heating your
milk at the same time as heating
your coffee or several minutes before
making coffee to ensure milk is hot.
1
2
Fill the stainless steel milk jug
provided with the required amount of
milk. Do not exceed the maximum
level or add less than the minimum
level.
1
Place the jug on the hot plate and
switch on D.
NOTE: You can turn on the hot plate
at the same time as the coffee
hotplate. It will take approximately
5-7 minutes for the milk to heat up to
it’s optimum frothing temperature.
3
If the milk has been left for a long
time, the cowl and blade can be
removed and soaked in hot soapy
water for 2-5 minutes before rinsing
clean.
2
Lift the milk jug up to the milk frother
blade E. Raise the milk jug, ensuring
that the cowl is just under the
surface of the milk - this will give the
maximum froth. Maintain the milk jug
in this position between 30-60
seconds.
NOTE: The jug can stay on the hot
plate until the coffee has finished
brewing, but be careful not to burn
your milk/froth.
5
6
Pour the coffee into cups and gently
pour or preferably spoon the milk
onto the coffee, then sprinkle a little
chocolate powder for the perfect
cappuccino.
Remove the cowl directly after use
and rinse in warm water F. It is
recommended that you clean the
blade immediately after use, as dried
milk can be difficult to remove.
If further cleaning is required, the
propeller and shaft can be removed.
To replace, insert the stem of the
milk frother blade into the mounting
hole on the unit and screw into place
G.
F
NOTE: If the blade is removed,
ensure that it is fully tightened in
place otherwise the frother will not
operate properly.
3
Place the milk jug back on the hot
plate to reheat the milk and preserve
the quality of the froth.
E
The frother blade can be wiped clean
still attached to the machine.
WARNING: Take care as the milk
will be hot.
4
D
There may be some splash back of
milk on the underside of the frothing
unit. Switch the unit off then simply
wipe this area clean with a damp
cloth.
WARNING: THE FROTHER ONLY
OPERATES CORRECTLY WHEN
THE COWLING IS CORRECTLY
ASSEMBLED.
G
DO NOT OPERATE THE FROTHER
DRY OR NOT SUBMERSED IN
LIQUID FOR LONG PERIODS OF
TIME.
Turn off the milk frother hot plate by
pressing the on/off switch.
WARNING: The stainless steel jug
and the hotplate will remain hot
for sometime after switching off.
For details of other Morphy Richards products, please see our website:
5
47008 rev4:x 13/11/2009 10:54 Page 6
RECIPES
1
Prepare coffee as per ‘making a
coffee’ instructions.
2
Fill the stainless steel milk jug with
the required amount of milk, place
on the hotplate and switch on. The
milk will take approx. 5-7 minutes to
reach the appropriate temperature.
3
Froth milk by lifting the milk jug up to
the milk frothing blade, ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx.
30-60 seconds to froth.
4
Prepare the hot chocolate according
to the instructions.
5
Pour the coffee, hot milk and hot
chocolate into a tall glass and serve.
Cappuccino
•
1
•
1
•
1
•
Chocolate powder for sprinkling
1
Prepare coffee as per ‘making a
coffee’ instructions.
2
Fill the stainless steel milk jug with
the required amount of milk, place
on the hotplate and switch on. The
milk will take approx. 5-7 minutes to
reach the appropriate temperature.
3
4
5
⁄ 3 coffee
⁄ 3 hot milk
⁄ 3 hot frothed milk
Froth milk by lifting the milk jug up to
the milk frothing blade, ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx.
30-60 seconds to froth.
Pour the coffee in first and then the
hot milk into a cappuccino cup,
spoon over frothed milk.
Sprinkle with chocolate powder to
serve.
Cafe Latte
•
1
•
1
1
Prepare coffee as per ‘making a
coffee’ instructions.
2
Irish coffee
Makes 2 servings
•
40ml of double cream
•
2 tsp sugar
•
4 shots of Irish whisky
•
350ml hot strong coffee
1
Whip double cream until thick then
chill.
2
Warm 2 Irish coffee glasses with hot
water and place in each a teaspoon
of sugar and 2 shots of Irish whisky.
3
Divide coffee among the glasses.
4
Slowly dribble the chilled cream over
the back of the spoon.
5
Do not stir.
⁄ 2 coffee
⁄ 2 hot frothed milk
Fill the stainless steel milk jug with
the required amount of milk, place
on the hotplate and switch on. The
milk will take approx. 5-7 minutes to
reach the appropriate temperature.
Amaretto coffee
3
4
Froth milk by lifting the milk jug up to
the milk frothing blade, ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx.
30-60 seconds to froth.
Pour the coffee into a tall glass and
top with the frothed milk.
Moccacino
6
•
1
•
1
•
1
UK Helpline 0844 871 0946
•
250ml hot strong coffee
•
2 tablespoons of double or whipped
cream
•
2 shots of Amaretto
•
Sugar to taste
1
Stir the coffee and alcohol together
either with a couple of tablespoons
of double-cream, or top with a dollop
of whipped cream.
2
Sprinkle with grated chocolate and
serve.
⁄ 3 coffee
⁄ 3 hot frothed milk
⁄ 3 hot chocolate
Replacement Parts 0844 873 0712
Ireland Helpline 1800 409 119
47008 rev4:x 13/11/2009 10:54 Page 7
HINTS AND TIPS
Wash the milk frother blade, milk
frother attachment, milk frother jug,
glass jug, and filter holder, in warm
soapy water. Rinse and dry all parts
thoroughly. Refit filter, filter holder,
milk frother blade, and milk frother
attachment.
CLEANING AND
MAINTENANCE
Refilling
1
2
Switch off the coffee maker, and
allow 5 minutes to cool.
Wipe all external surfaces with a
damp cloth and dry thoroughly.
Lift the hinged reservoir and refill
with cold water.
Care must be taken to ensure the
non-drip valve situated on the
bottom of the filter holder is not
damaged during cleaning.
Descaling
•
If you live in a harder water area, we
recommend that your coffee maker
is descaled at regular intervals, eg.
every 2 - 3 months. In areas of
moderately hard water you should
descale every 6 months.
•
If the water filters through more
slowly than usual, it is a sign that
descaling is necessary.
•
We recommend you to use
proprietary liquid descaler which is
especially made for coffee makers
and plastic kettles. Follow the
instructions on the bottle or sachet,
and then operate the coffee maker
with just water 3 times before
making coffee.
•
Never use harsh or abrasive
cleaners.
MILK FROTHER PARTS
(EXCLUDING MILK FROTHER JUG)
ARE DISHWASHER SAFE.
HELPLINE
If you have any difficulty with your
appliance, do not hesitate to call. We
are more likely to be able to help
than the store from where you
bought it.
Please have the following information
ready to enable our staff to deal with
your enquiry quickly:
•
Name of the product.
•
Model number as shown on the
underside of the appliance.
NOTE: The permanent mesh filter
should not be used during descaling.
•
Serial number as shown on
underside of the appliance.
Cleaning care
UK Helpline
Unplug the coffee maker, and allow
to cool.
Replacement Parts 0844 873 0712
Do not use kettle descaler unless the
packet specially states it is suitable
for coffee makers.
Ireland Helpline
Do not immerse the coffee maker in
liquid.
Rinse the water tank occasionally
with cold water. Do not use a cloth
as any residue or lint left behind may
clog the coffee maker.
Remove the permanent filter, discard
used coffee and wash with warm
soapy water. Extended soaking helps
remove coffee stains from the mesh.
Rinse and dry thoroughly.
0844 871 0946
1800 409 119
WEBSITE
You may also contact us through our
website, or visit the site to browse
and purchase appliances, spare parts
and accessories from the extensive
Morphy Richards range.
For details of other Morphy Richards products, please see our website:
7
47008 rev4:x 13/11/2009 10:54 Page 8
REGISTERING
YOUR TWO YEAR
GUARANTEE
Your standard one year guarantee is
extended for an additional 12
months when you register the
product within 28 days of purchase
with Morphy Richards. If you do not
register the product with Morphy
Richards within 28 days, your
product is guaranteed for 1 year. To
validate your 2 year guarantee
register with us online at
www.morphyrichards.co.uk
N.B. Each qualifying product needs
to be registered with Morphy
Richards individually.
Please note that the 2 year
guarantee is only available in the
UK and Ireland. Please refer to the
one year guarantee for more
information.
YOUR ONE YEAR
GUARANTEE
It is important to retain the retailer’s
receipt as proof of purchase. Staple
your receipt to this back cover for
future reference.
Please quote the following
information if the product develops
a fault. These numbers can be
found on the base of the product.
Model no.
Serial no.
All Morphy Richards products are
individually tested before leaving
the factory. In the unlikely event of
any appliance proving to be faulty
within 28 days of purchase, it
should be returned to the place of
purchase for it to be replaced.
If the fault develops after 28 days
and within 12 months of original
purchase, you should contact the
Helpline number quoting Model
number and Serial number on the
product, or write to Morphy
Richards at the address shown.
Subject to the exclusions set out
below (see Exclusions), the faulty
appliance will then be repaired or
replaced and dispatched usually
within 7 working days of receipt.
If, for any reason, this item is
replaced during the 1 year
guarantee period, the guarantee on
the new item will be calculated from
original purchase date. Therefore it
is vital to retain your original till
receipt or invoice to indicate the
date of initial purchase.
To qualify for the 1 year guarantee,
the appliance must have been used
according to the instructions
supplied. For example, crumb trays
should have been emptied regularly.
6 Morphy Richards are not liable to
carry out any type of servicing
work, under the guarantee.
7 Plastic filters for all Morphy
Richards kettles and coffee makers
are not covered by the guarantee.
8 Batteries and damage from leakage
are not covered by the guarantee.
• This guarantee does not confer any
rights other than those expressly
set out above and does not cover
any claims for consequential loss or
damage. This guarantee is offered
as an additional benefit and does
not affect your statutory rights as a
consumer.
• This guarantee is valid in the UK
and Ireland only.
EXCLUSIONS
Morphy Richards shall not be liable
to replace or repair the goods under
the terms of the guarantee where:
1 The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturer’s
recommendations or where the fault
has been caused by power surges
or damage caused in transit.
2 The appliance has been used on a
voltage supply other than that
stamped on the products.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore reserves the right to change the specification of
it’s models at any time.
UK Helpline 0870 060 2614
4 The appliance has been used for
hire purposes or non domestic use.
5 The appliance is second hand.
You may be asked to return a copy
of proof of purchase.
Morphy Richards products are intended for household use only.
See usage limitations within the location safety instructions.
8
3 Repairs have been attempted by
persons other than our service staff
(or authorised dealer).
Replacement Parts 0870 157 6645
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should
not be disposed of with household
waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice in your
country.
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
Helplines (office hours)
UK 0844 871 0946
Spare Parts 0844 873 0712
Republic of Ireland 1800 409 119
CM47008 MUK Rev4 11/09
Ireland Helpline 1800 409119

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement