Acnodes RM9230 1080P / 4K LCD Display User Manual

DP 1.2 + HDMI 1.4 Video Input
9U high rack mount monitor
Industrial Monitors
RM9230
23" 4K 3840 x 2160 LCD panel
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710
Tel: 909.597.7588
© Copyright 2019 Acnodes Corp.
Fax: 909.597.1939
Legal Information
First English printing, July 2018
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■
■
■
■
■
■
■
■
■
■
■
Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
Observe all precautions and warnings attached to the equipment.
If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■
■
■
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
□
□
□
□
□
□
□
□
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■ Re-position or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > RM9230
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Installation
P.1
P.1 - 2
P.3 - 4
< Part. 2 > Specifications / OSD / Remote Controller
2.1
2.2
2.3
Product Specifications
On-screen Display Operation ( OSD )
Picture In Picture ( PIP ) / Picture By Picture ( PBP )
P.5 - 6
P.7 - 9
P.10 - 11
< Part. 3 > Options
3.1
3.2
3.3
3.4
3.5
3G / HD / SD-SDI Broadcast-grade input
MCS Multi-display control solution
Touchscreen : Projected Capacitive 10-point
Resistive 1-point
DC Power : 12V / 24V / 48V / 125V
MIL-type or lockable connector
P.12
P.13
P.14 - 15
P.16
P.17
Before Installation
■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■
To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■
Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
■
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content
RM9230 unit X 1
- 6ft DP cable X 1
- Power adapter X 1
- Power cord X 1
- Fastener screw for rear bracket x 2
< 1.2 > Structure Diagram
Front view
3
1
Power adapter
2
Rear view
4
5
1
LCD panel
2
LCD membrane
3
Latch to release the display panel from the
rear bracket
4
Rear mounting bracket
5
Power adapter basket
HDMI 1.4
Power cord
HDMI 2.0 DP
Power in
Basic I/O
: Display port 1.2 + HDMI 1.4 + HDMI 2.0
Options
: SDI, USB for touchscreen & DC power
P.1
< 1.2 > Dimension
RM9230
Front View
Side View
UNIT : mm
Bottom View
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
RM9230
551 x 65 x 385 mm
21.7 x 2.6 x 15.2 inch
583 x 124 x 529 mm
23 x 4.9 x 20.8 inch
8.8 kg
19.4 lb
11.2 kg
24.6 lb
P.2
< 1.3 > VESA mount Installation
M4 screw
VESA mount ( 100*100mm )
■
Hardware and M4*4 pcs for VESA mount are not provided
P.3
< 1.3 > Rear Mounting Bracket Installation
RM9230
Step
■
■
1
Mount the rear bracket with M6 screw set.
8 x M6 screw set are required.
M6 screw sets are not provided.
Step
■
Insert the RP-K923 display panel into the
rear bracket.
Step
■
2
3
Fix the unit to the bracket with the top latch.
Step
4
Complete the installation
P.4
< Part 2 >
< 2.1 > Product Specifications
LCD
Panel
Native Resolution
3840 x 2160
23.8-inch TFT color LCD
Panel Size ( diagonal )
Brightness ( cd/m² )
310
Contrast Ratio ( typ. )
1000:1
Colors
1.07 Billion, 10-bit
Viewing Angle ( L/R/U/D )
89/89/89/89
Response Time ( ms )
25
Dot pitch ( mm )
0.13725
Display Area ( mm )
527.04H x 296.46V
Surface treatment
Anti-glare
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
Video
Digital
30,000
Display port
DP 1.2
/ HDCP 1.3
HDMI
HDMI 1.4 / HDCP 1.4
HDMI 2.0 / HDCP 2.2
Audio
Audio Output
Speaker
Connector
3.5mm stereo jack
Resistance / Power level
30kΩ / 2.8V
Dual Stereo Speaker
2W x 2
*When the audio output is connected, speaker output is OFF
Power
Compliance
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen ON
Max. 29W
Power saving mode
Max. 9W
Power button OFF
Max. 2W
EMC
FCC & CE certified
Safety
CE / LVD certified
Environment
RoHS2 & REACH compliant
P.5
RM9230
Environmental
Conditions
Operating
Storage / Non-operating
Physical
Specification
Temperature
0 to 55°C degree
Humidity
20~90%, non-condensing
Altitude
16,000 ft
Temperature
-20 to 60°C degree
Humidity
5~90%, non-condensing
Altitude
40,000 ft
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Product ( W x D x H )
480 x 48 x 266 mm
18.9 x 1.9 x 10.5 inch
Packing ( W x D x H )
529 x 124 x 451 mm
20.8 x 4.9 x 17.8 inch
Applicable
Format
Net Weight
4.2 kgs / 9.2 lbs
Gross Weight
6.2 kgs / 13.6 lbs
Display Port Input
PC Signal
3840 x 2160 x 60Hz
1920 x 1080 x 60Hz
1600 x 1200 x 60Hz
1360 x 768 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 768 x 60Hz
1024 x 768 x 60 / 70 / 75Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
HDMI Input
Audio Signal
2ch Linear PCM
HDMI 2.0
3840 x 2160 x 60Hz
HDMI 2.0 / 1.4
3840 x 2160 x 30Hz
1920 x 1080 x 50 / 60Hz ( 1080p )
1920 x 1080 x 25 / 30Hz ( 1080i )
1280 x 720 x 50 / 60Hz ( 720p )
720 x 480 x 50 / 60Hz ( 576p / 480p )
Audio Signal
2ch Linear PCM
*In some circumstances, if the user connects the LCD to PC via HDMI port
or video and audio signals, the LCD may display incorrectly on a full screen.
If so, please adjust the display card setting on display size to fix the issue.
P.6
< 2.2 > On-screen Display Operation ( OSD )
Membrane Switch
Function
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting options
Scroll through menu options and adjust
the displayed control
Exit the OSD screen
Go back to the previous on-screen sub-menu or
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power
touch button will flash continuously when there is no signal input.
1
All the LED touch buttons will automatically turn off after 10 minutes of idle status ( except the Power
2
Light up all membrane buttons, please press any button for 1 - 2 seconds ( except the Power
P.7
).
).
< 2.3 > On-screen Display Operation ( OSD )
1
Picture
Brightness : Adjust the screen brightness
Contrast
: Adjust the difference between the image background
( black level ) and the foreground ( white level )
Black level : Adjust background black level of the screen
Eco
2
: Screen in power saving mode
Position
Picture size : Adjust the image size
- Full Screen / 4:3 / 5:4 / Pixel to Pixel
DP version : Select the DP version
3
Color
Color temperature : User / Warm / Cool / 5400k mode and
Red / Green / Blue color balance
Sharpness
: Adjust the image from weak to sharp
Hue
: Adjust the screen hue value
Saturation
: Adjust the saturation of the image color
Dynamic
luminous control
: Control the dynamic brightness
4
OSD Set
Language
: Select the language in which the OSD menu is
displayed - English
OSD H-Position
: Align the screen image left or right
OSD V-Position
: Align the screen image up or down
OSD time out
: Adjust the screen timeout
OSD transparency : Adjust the screen transparency
OSD size
: Adjust the screen size - Normal / Small
OSD rotation
: Rotate the screen - 90° / 180° / 270°
P.8
RM9230
< 2.3 > On-screen Display Operation ( OSD )
5
Reset
Reset
6
: Return the adjustment back to factory setting
PIP
PIP mode
: Enter into PIP / PBP setting - PIP MODE /
PBP 2WIN ( Main screen + 1 sub screen ) /
PBP 3WIN ( Main screen + 2 sub screen ) /
PBP 4WIN ( Main screen + 3 sub screen )
Select the signal input of each sub screen
PIP size
: Adjust the size of the Sub screen
- Small / Medium / Large / Huge
PIP position
: Adjust the position of the Sub screen
- Top Left / Top Right / Bottom Left / Bottom Right
Swap
: Swap the input signal of PIP / PBP sub screen
7
MISC
Signal source : Select the signal source - DP / HDMI1 / HDMI2
Mute
: Turn off the surrounding sound
Audio in
: Auto / Line in / DP
Volume
: Adjust the volume of sound
Sleep mode
: Set the off time - 10 min / 20 min / 30 min /
50 min / 60 min / 120 min / 240 min
Options on Reset page
Rotation
: Rotate the image in Full screen or 1:1
- 90° / 180° / 270°
Picture size : Adjust the image size in Full screen or 1:1
P.9
< 2.3 > How to Use Picture In Picture ( PIP ) /
Picture By Picture ( PBP )
< 2.3.1 > Picture in Picture ( PIP )
Mode
Display the Sub screen in the Main screen.
OSD Menu → MISC → PIP Mode → Large / Small / OFF
Main screen
Sub screen
Position
Adjust the position of the Sub screen ( top left, bottom left, top right, bottom right )
OSD Menu → MISC → PIP Position → top left / top right / bottom left / bottom right
top left
top right
bottom left
bottom right
Size
Adjust the size of the Sub screen ( Large / Small )
OSD Menu → MISC → PIP Mode → Large / Small
Size of Sub screen
LCD Monitor
Large Sub screen
Small Sub screen
1920 x 1200
552 x 414
480 x 360
1920 x 1080
552 x 414
480 x 360
1440 x 900
414 x 310
360 x 270
1366 x 768
392 x 294
340 x 254
1280 x 1024
368 x 276
320 x 240
P.10
< 2.3.2 > Picture By Picture ( PBP )
Mode
Display the Sub screen next to the Main screen.
OSD Menu → MISC → PIP Mode → PBP
Main screen
Sub screen
Size
LCD Monitor
Main / Sub screen
1920 x 1200
955 x 716
1920 x 1080
955 x 716
1440 x 900
715 x 536
1366 x 768
678 x 508
1280 x 1024
635 x 476
< 2.3.3 > PIP / PBP Source
To select an input signal for PIP / PBP Sub screen.
OSD Menu → MISC → PIP Source → HDMI / SDI
The PIP / PBP is operable in the following table :
Sub
HDMI
SDI
HDMI
x
o
SDI
o
x
Main
P.11
< Part 3 >
< 3.1 > Options : 3G / HD / SD-SDI input
RM9230
Austin Hughes’ SDI input is an ideal solution for the broadcastgrade video and high resolution CCTV market.
Designed for use with CyberView displays, a SDI input
module can support up to 1080p @60Hz resolution without
using additional space or power and it comes standard with a
2-year warranty.
SDI
HDMI 1.4
in
-
Audio
OUT
HDMI 2.0 DP
Power
in
out
INPUT
Standard Compliance
Compatible Video Format
Compatible Audio Format
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
3G-SDI
1080p
1080p
1080i
720p
@60 / 50Hz, 4:2:2
@30 / 25 / 24Hz, 4:4:4
@60 / 50Hz, 4:4:4
@60 / 50Hz, 4:4:4
HD-SDI
1080p
1080i
720p
@30 / 25 / 24Hz, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
P.12
< 3.2 > Options : MCS
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Austin Hughes provides MCS solution to control the OSD of
various CyberView LCD display up to 64 units.
The RS-232C is used for the communication between the PC and the
first display via a 15 feet serial cable while the CAN bus is used for the
various LCD displays cascade together via CAT 5/6 cable, and daisy
chain up to 1,000 meters.
Designed for use with CyberView LCD displays, Austin Hughes
provides a MCS input module without using additional space or power
and it comes standard with a 2-year warranty.
MCS
HDMI 1.4
Link
in
out
Audio
OUT
HDMI 2.0 DP
Power
in
set
*** Please download the protocol of MCS control at :
http://www.austin-hughes.com/support/usermanual/cyberview/UM-CV-MCS.pdf
Set switch
For the 1st and last display,
push the set switch upward
RS-232C
For other daisy chain displays,
push the set switch downward
15 feet serial cable
( over 15 feet, extender required )
B
A
LINK
OUT
IN
Cat5 / 6 cable
max. 300 meters
D
C
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
OUT
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
P.13
up to 64 displays
< 3.3 > Options : Touchscreen & driver
RM9230
K23" USB Touchscreen Specification
TCB-10
Model
TRB
Multi-touch
e-Resistive
Technology
Projected Capacitive
5-Wire Resistive
Touch Point
10 point touch standard
( special requirement available )
Single
Input Type
Finger or Capacitive Stylus
Finger or Stylus
Resolution
4096 x 4096
2048 x 2048
Touch Point Accuracy
± 2 mm
-
Response Speed
< 5 ms
15 ms
Activation Force
<5g
≤ 50 g
6H
3H
> 85%
80% ± 3%
3%↓
8% ± 3%
Durability
50 million touches
10 million touches
Top Layer
3 mm Glass
ITO Film
0.7 mm Sensor Glass
ITO Glass
Thickness
3.9 ± 0.1 mm
2.2 ± 0.2 mm
Connector
USB
USB Type A
Windows 7 / XP / Linux / Mac
Windows / Linux / Android / Mac
Surface Hardness
Light Transmission
Haze
Bottom Layer
Compatibility
Model
IR-06
Infrared
Technology
Infrared
Touch Point
6
Input Type
Pen, Finger, Finger of gloved hand activation
Touch Point Accuracy
± 2 mm
Response Speed
≤ 8 ms
Activation Force
No minimum touch activation force
Touch Durability
Unlimited
Glass Thickness
2 mm
Connector
A-type USB
Operating System
■
■
■
■
Windows 7 / Windows 10
Dimension will be changed if Multi-touch required
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
For detailed information, please refer to the attached CD disc
As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
HDMI 1.4 HDMI 2.0
DP
P.14
Power
in
< 3.3 > Options : Touchscreen & driver
Connect the USB cable from the USB port on the LCD to a computer. The touch screen supports
easy Plug-and-Play operations. There is no need to install additional drivers on the computer.
TRB / TCB Driver
Please follow the below steps to setup the touch screen:Step 1. Run the bundled CD disc or download the driver from the link below :
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finishthesetup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
P.15
RM9230
< 3.4 > Options : DC Power
Model
12V
24V
48V
125V
Input rating
Input voltage:
12-Volt
24-Volt
48-Volt
110-Volt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
66 ~ 160V
- No load
50 mA
50 mA
50 mA
35 mA
- Full load
7183 mA
3551 mA
1755 mA
749 mA
Output voltage:
12-Volt
12-Volt
12-Volt
12-Volt
Output current:
6.25A
6.25A
6.25A
6.25A
Efficiency
87%
88%
89%
91%
Input current
Output rating
***
For DC power option :
( 1 ) If the unit with LCD, earthing
may be required
P.16
< 3.5 > Options : MIL-type or Lockable Connector
Input
MIL - type
Connector
Part no.
MIL Standard
DC Power ***
( Male )
MS3470W8-33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design flexibility possible. For more information, please contact us.
Input
Lockable
Connector
Part no.
DC Power
( Male )
YM-Ext-461CP001
USB
LUSB - A111 - 00
Standard
D-type 3W3
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
P.17
The company reserves the right to modify product specifications without prior notice and assumes no responsibility
for any error which may appear in this publication.
All brand names, logo and registered trademarks are properties of their respective owners.