Cyberdata 011214 SIP Outdoor Intercom with Keypad Owner manual

Connecting the Keypad Intercom (Service Loop Routing)
Ground Cable Installation
Route cable(s) inside of the
Gang Box to create the service loop.
Ground Cable
(not provided)
Network Cable Installation
Network Cable
(not provided)
Installation Quick Reference
Route cable(s) inside of the
Gang Box to create the service loop.
The IP Endpoint Company
VoIP Outdoor Keypad Intercom
SIP Compliant
011214
Parameter
Ground Lug
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
a
Nut (to Ground Lug
inside of the Gang Box
Subnet Mask
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Securing the Intercom
Typical System Installation
Caution
GENERAL ALERT
Factory Default Setting
Generic PoE Switch
*More installation and mounting
information is illustrated in the
Operations Guide.
Equipment Hazard: Do not use an electric or power
screwdriver to fasten the face plate and PCB assembly to the
gang box. To prevent over-torque damage to the gasket, do
not apply more than 10 inch-pounds force. Over-torquing
will cause the gasket to tear, risk moisture intrusion, and
effectively void the manufacturer's warranty.
1
2
3
4
5
6
Note: To mount the intercom, use methods
compliant with local electrical codes.
Door Strike
Note: More installation and mounting
information is illustrated in the Keypad
Intercom Operations Guide.
IP Phone
VoIP Intercoms with Keypad
IP PBX Server
Getting Started
•
Download the Operations Guide PDF file from the Documents page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercomkeypadv3/index.html
Torx Key
3-Gang Box
Faceplate &
PCB Assembly
Torx Screws
•
Create a plan for the locations of your Keypad Intercoms.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Keypad Intercom Parts
Contacting CyberData
Accessories
(1) Intercom Assembly
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
531085B Hole Plug Assembly
Carriage Bolt Bolts
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930520G
Spacer for Half-inch Set Screw Connector
Carriage Bolt Nuts
Mounting Component Security Torx Key
Quick Reference
Quick Reference
Carriage Bolt Washers
930520G
Accessory Kit
Accessory Kit Security Torx MS
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
Features
Dimensions (Rear View and Mounting Holes)
Dimensions (Front and Side View)
5.118 [130.00]
5.198 [132.03]
3.740 [95.00]
Microphone
Hole
ø0.280 [ø7.11]
(3 Places)
0.869 [22.07]
Speaker
Drain Hole
ø0.854 [ø21.69]
Call Button
7.480 [190.00]
2.284 [58.01]
1.690 [42.93]
DIMENSIONS ARE IN INCHES [MILLIMETER]
Terminal Block Connections
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
3
Wire (IN)
Terminal Block
can accept
16 AWG wire
J3 Terminal Block
1.690
[42.93]
Alternate Power Input:
1 = +12 to +24 VDC at 1000 mA
(500 mA Minimum)
2 = Power Ground
3
4
Relay Contact:
(1A at 30 VDC for Continuous L
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Refere
4
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
*Contacts 1 and 2 on the J3 terminal block are only
for powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
3.380 [85.85]
Dimensions are in Inches [Millimeter]
Conduit Mounting Restrictions (Rear Entry)
With Shroud
Without Shroud
RTFM Button
Add
Spacer
Here
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
SW1
1/2" Conduit
Connector
(Not Provided)
Add 1/2" Conduit
Spacer Connector
Here (Not Provided)
1/2" Conduit
(Not Provided)
1/2" Conduit
(Not Provided)
To announce the device’s current IP address:
•
Press and release the RTFM button within a five
second window.
Note
Network
Cable
(Not Provided)
The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
Network
Cable
(Not Provided)
To restore the device to factory default settings:
•
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930520G
Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
Quick Reference
Quick Reference
930520G
© 2015, CyberData Corporation, ALL RIGHTS RESERVED