ESAB | PEK A2 | Instruction manual | ESAB PEK A2 User manual

ESAB PEK A2 User manual
A2, A6 PEK Control Unit
Instruction manual
0460 948 101 GB 20140225
Valid for: serial no. 327-xxx-xxxx
TABLE OF CONTENTS
1
SAFETY ................................................................................................................ 4
2
INTRODUCTION ................................................................................................... 7
2.1
Equipment............................................................................................................. 7
2.2
Control panel ........................................................................................................ 7
3
TECHNICAL DATA ............................................................................................... 8
4
INSTALLATION..................................................................................................... 9
4.1
5
6
OPERATION ....................................................................................................... 10
5.1
Connections ....................................................................................................... 10
5.2
USB connection ................................................................................................. 10
5.3
Key to symbols................................................................................................... 11
MAINTENANCE .................................................................................................. 12
6.1
7
Mains supply ........................................................................................................ 9
Inspection and cleaning .................................................................................... 12
ORDERING SPARE PARTS ............................................................................... 13
DIAGRAM .................................................................................................................. 14
ORDERING NUMBERS .............................................................................................16
ACCESSORIES .........................................................................................................17
Rights reserved to alter specifications without notice.
0460 948 101
© ESAB AB 2014
1 SAFETY
1
SAFETY
NOTE!
The unit is tested by ESAB in a general set-up. The responsibility for safety and
function, of the specific set-up, lies with the integrator.
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment when it
is started up
○ no-one is unprotected when the arc is struck or work is started with the equpment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could
become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinquishing equipment must be clearly marked and close at hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Risk of crushing when replacing the wire bobbin! Do not use safety gloves when
inserting the welding wire between the feed rollers.
0460 948 101
-4-
© ESAB AB 2014
1 SAFETY
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting. Ask for your employer's safety practices which should
be based on manufacturers' hazard data.
ELECTRIC SHOCK - Can kill
•
•
•
•
Install and earth the unit in accordance with applicable standards
Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing
Insulate yourself from earth and the workpiece
Ensure your working stance is safe
FUMES AND GASES - Can be dangerous to health
•
•
Keep your head out of the fumes
Use ventilation, extraction at the arc, or both, to take fumes and gases away
from your breathing zone and the general area
ARC RAYS - Can injure eyes and burn skin
•
•
Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing
Protect bystanders with suitable screens or curtains
FIRE HAZARD
•
Sparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby
NOISE - Excessive noise can damage hearing
•
•
Protect your ears. Use earmuffs or other hearing protection. Protect your
ears. Use earmuffs or other hearing protection
Warn bystanders of the risk
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of
class A equipment in those locations, due to conducted
as well as radiated disturbances.
0460 948 101
-5-
© ESAB AB 2014
1 SAFETY
CAUTION!
Read and understand the instruction manual before
installing or operating.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2002/96/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law, electrical
and/or electronic equipment that has reached the end of
its life must be disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
0460 948 101
-6-
© ESAB AB 2014
2 INTRODUCTION
2
INTRODUCTION
PEK is a control unit intended for submerged arc welding (SAW) and for gas metal arc
welding (GMAW). The control unit is used together with automatic welding machines, power
sources, column and booms.
ESAB's accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1
Equipment
The control unit is supplied with:
•
•
An instruction manual for the control unit
An instruction manual for the control panel in English
Instruction manuals in other languages can be downloaded from: www.esab.com.
2.2
Control panel
See the separate instruction manual for a detailed description of the control panel
0460 948 101
-7-
© ESAB AB 2014
3 TECHNICAL DATA
3
TECHNICAL DATA
PEK
Supply voltage
42 V, 50/60 Hz
Power requirement
Max 900 VA
Engine connections adapted for ESAB's
motors
6 A 100%
Speed control
Feedback from pulse encoder
Operating temperature
-15°C to +45°C
Transportation temperature
-20°C to +55°C
Relative air humidity
Max 95%
Dimensions l×w×h
246 × 235 × 273 mm
Weight
6.6 kg
Enclosure class
IP23
Travel speed
0–200 cm/min *)
See separate instruction manual for
automatic welding machines.
Max manual travel speed
2.0 m/min
Wire feed speed, filler wire
0–2500 cm/min *)
See separate instruction manual for wire feed
unit.
*) The setting range is dependent on the product used.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
0460 948 101
-8-
© ESAB AB 2014
4 INSTALLATION
4
INSTALLATION
The installation must be executed by a professional.
4.1
Mains supply
NOTE!
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains
supply, influence the power quality of the grid. Therefore connection restrictions
or requirements regarding the maximum permissible mains impedance or the
required minimum supply capacity at the interface point to the public grid may
apply for some types of equipment (see technical data). In this case it is the
responsibility of the installer or user of the equipment to ensure, by consultation
with the distribution network operator if necessary, that the equipment may be
connected.
0460 948 101
-9-
© ESAB AB 2014
5 OPERATION
5
OPERATION
General safety regulations for the handling of the equipment can be found in the "SAFETY"
chapter of this manual. Read through before you start using the equipment!
5.1
Connections
1. Emergency stop
7. Connection of speed feedback for travel
motion
8. Connection for arc voltage feedback
2. Control panel, see separate instruction
manual
3. Connection (CAN) for remote control unit 9. Connection of motor cable for travel
or service tool
motion
4. USB connection, see section of USB
10. Connection of motor cable for wire feed
connection
5. Connection for limit position switch or
11. Connection for control cable from power
cable with solenoid for gas
source
6. Connection of speed feedback for wire
feed
5.2
USB connection
The external USB memory can be used to transfer programs to and from systems.
During normal use there is no risk of ”viruses” ”infecting” equipment. To eliminate the risk
entirely, we recommend that the memory, which is used together with this equipment, not be
used for any other purpose other than its intended.
Certain USB memories may not work with this equipment. We recommend using USB
memories from a reputable supplier.
ESAB assumes no responsibility for any damage caused as a consequence of incorrect use
of the USB memory.
0460 948 101
- 10 -
© ESAB AB 2014
5 OPERATION
To insert a USB memory
1. Switch off the power supply main switch.
2. Insert the USB memory into the USB socket.
3. Switch on the power supply main switch.
5.3
Key to symbols
Main menu
Enter
Manual travel motion
Manual travel motion
in direction
in direction
Fast motion
Manual wire feed
upwards
Manual wire feed
downwards
Start
Stop
Current
Wire feed speed
Voltage
Travel speed
See separate instruction manual for more information regarding the control panel.
0460 948 101
- 11 -
© ESAB AB 2014
6 MAINTENANCE
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Maintenance may only be carried out by an authorised technician. Only personnel with the
appropriate electrical skills (authorised staff) may remove safety plates.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer
attempts any work to rectify any faults in the product during the warranty period.
6.1
Inspection and cleaning
Check regularly that the control unit is not clogged with dirt.
How often and which cleaning methods apply depend on:
•
•
•
•
welding process
arc time
location of the unit
surrounding environment
Usually it will be sufficient to blow the unit clean once a year, using dry compressed air
(reduced pressure).
0460 948 101
- 12 -
© ESAB AB 2014
7 ORDERING SPARE PARTS
7
ORDERING SPARE PARTS
Repair and electrical work should be performed by an authorised ESAB service technician.
Use only ESAB original spare and wear parts.
PEK is designed and tested in accordance with the international and European
standards EN 60974-1 and EN 60974-10. It is the obligation of the service unit which
has carried out the service or repair work to make sure that the product still conforms
to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this
publication.
0460 948 101
- 13 -
© ESAB AB 2014
DIAGRAM
DIAGRAM
Updates:
From serial no. 921-010-XXXX: Cable 18.1 removed
From serial no. 921-010-XXXX: Wire jumper X1:12 to X1:15 introduced
0460 948 101
- 14 -
© ESAB AB 2014
DIAGRAM
0460 948 101
- 15 -
© ESAB AB 2014
ORDERING NUMBERS
ORDERING NUMBERS
Ordering no.
Denomination
Type
0460 504 880
Control unit
PEK
0459 839 036
Spare parts list
PEK
0460 949
Instruction manual
Control panel for PEK
Instruction manuals and the spare parts list can be downloaded from: www.esab.com
0460 948 101
- 16 -
© ESAB AB 2014
ACCESSORIES
ACCESSORIES
Control cable PEK - Power source
0460 910 881
15 m
0460 910 882
25 m
0460 910 883
35 m
0460 910 884
50 m
Cable restraining bracket
0460 861 880
USB Memory stick 2 Gb
0462 062 001
0460 948 101
- 17 -
© ESAB AB 2014
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Heist-op-den-Berg
Tel: +32 15 25 79 30
Fax: +32 15 25 79 44
BULGARIA
ESAB Kft Representative Office
Sofia
Tel: +359 2 974 42 88
Fax: +359 2 974 42 88
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
www.esab.com
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
SOUTH AFRICA
ESAB Africa Welding & Cutting
Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
USA
ESAB Welding & Cutting
Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising