Rane MS1S Mic Stage Data Sheet
Add to My manuals4 Pages
Rane MS1S Microphone Stage provides a professional-grade solution for connecting microphones to line-level inputs. With switchable 48V phantom power, continuous gain control, signal/overload indicators, and a polarity switch, the MS1S offers versatility and ease of use. Its true differential input with high common-mode rejection ensures exceptional performance, while the cross-coupled line driver delivers a strong, balanced output. Whether you're using dynamic, condenser, or electret microphones, the MS1S guarantees pristine audio quality for a wide range of applications.
advertisement
DATA SHEET / MANUAL MS1S
MICROPHONE STAGE
General Description
The Rane MS1S Mic Stage preamplifier provides the answer when you need just one microphone input in an otherwise line-level world. Give us a call to go from either a dynamic, condenser or electret microphone to a line-level input with a minimum of noise, distortion, cost and hassle.
The MS1S provides 48 V switchable Phantom Power with an indicator LED, continuous rotary Gain trim between 15 dB and 60 dB, Signal/Overload LED, and XLR balanced Input & Output connec tors. A Polarity switch and high-current cross-coupled output line driver round out the features.
The MS1S utilizes one of the finest ultra low noise amplifier designs available. Featuring a true differential input with high common-mode rejection, use of the MS1S guarantees performance usually found only in mixing consoles costing thousands of times as much. Of course, for all of that extra money you receive a proportional increase in KPSI (knobs per square inch).
The MS1S replaced the MS 1B Mic Stage with a new internal universal power supply. The width increased by one inch, all other features are the same.
Features
• -127 dB Equivalent Input Noise • Gain Control • Signal / Overload Indicator • Polarity Switch • Switchable 48 V Phantom Power • True Differential Input • Cross-coupled Line Driver • Internal 100-240 VAC Power Supply Data Sheet-1
MS1S
MICROPHONE STAGE
Features and Specifications
Parameter
Input Impedance Gain Range Phantom Power ..........Impedance
Max. Input Level Equivalent Input Noise Signal to Noise Ratio Dynamic Range CMRR Frequency Response THD+Noise (gain 60 dB) THD+Noise (gain 15 dB) Line Driver Max. Output Level Output Impedance Signal Indicator Overload Indicator Output Cable Length Maximum Power Universal Line Voltage Power Cord Unit: Conformity Unit Size ..........Weight
Shipping Size ..........Weight
Specification
2k 15 to 60 +48 6.81k
+9 / -35 -127 94 114 / 91 80 3 to 200k .004 (Output=+20 dBu) .0006 (Output=+20 dBu) Active Cross-coupled +18 / +24 94 -11 +20 1000 feet / 300 meters 3 100-240 C5 cord to C6 inlet FCC, CCSAUS 1.64"H x 6.8"W x 4.26"D 1 lb 1 oz 3.6"H x 11.75"W x 7.2"D 4 lb
Limit
1% typ.
4% 1% min.
typ.
typ.
typ.
typ.
typ.
typ.
typ.
Units Conditions/Comments
Ω dB V Ω dBu dBu dB dB dB Hz % % Balanced 10 mA max.
Each leg Gain 15 / 60, balanced output 20 kHz BW, Rs=150 Ω, Gain = 60 dB 20 kHz BW, Rs=150 Ω, Gain = 15 dB, re 4 dBu Gain 15 / 60, 20 Hz to 20 kHz Rs=150 Ω , 120 Hz, Gain = 60 dB +0, -3dB 55 Hz to 20 kHz, 20 kHz BW, Rl=10 kΩ 50 Hz to 20 kHz, 20 kHz BW, Rl=10 kΩ min.
1% typ.
typ.
typ.
dBu Ω dBu dBu W VAC Balanced, 2 kΩ load Each Leg Balanced output, Green LED Balanced output, Amber LED Belden 8451 or equivalent 50/60 Hz IEC 60320-1 (4.2 cm x 17.3 cm x 10.8 cm) (0.5 kg) (9.5 cm x 30 cm x 18 cm) (1.8 kg)
Data Sheet-2
MS1S
MICROPHONE STAGE
Block Diagram
+48V PHANTOM POWER MIC INPUT 3 2 1 RFI FILTER SIGNAL / OVERLOAD +6 dB INVERT 2 1 3 LINE LEVEL OUT GAIN 12-60 dB
Application Information
Uses and applications for the MS1S should be obvious. But then again, it’s obvious to us our taxes are too high and nothing is being done about that. With this in mind, perhaps a few words on us ing the MS1S might not be wasted.
BALANCED USE
The MS1S provides a true cross-coupled balanced output. This is equivalent to an electronic simulation of a transformer output. Rane follows the AES standard of pin 2 = hot.
When running a long cable back to the mixer, run a irritations.
line-level
balanced line rather than a mic-level line. The compact MS 1S can mount closer to the micro phone, provide a local volume control (or not, just pull the knob off), while the stronger signal minimizes RF and hum
UNBALANCED USE
Balanced use is recommended to mini mize noise. Unbalanced lines are usually quiet under 10 feet (3 meters), but longer runs will introduce the hum and interfer ence you are trying to avoid. When you must drive an unbalanced device with the MS1S's balanced output, keep the cable short, and connect pin 2 to the “+” or “hot” lead, and
tie pin 3 and ground together at the shield
.
MIXING
The MS1S is designed to fill the need for adding a microphone channel to line level mixers, such as the Rane SM 26S or SM 82S. Many installations using either of these products invariably wind up with one unused input that would do the job perfectly if only it could operate at mic level. In rides the MS1S to the rescue.
DIGITAL RECORDING AND SAMPLING
Another handy use for the MS1S is in recording applications. Many popular products do not have a high enough qual ity mic preamp to suit the resolution of the digital processing electronics. Such irony. Using the ultra low noise MS1S to bring the mic inputs up to extremely high quality line-level is an easy and affordable solution for this dilemma. No garbage in; no garbage out.
Clippity-clop; clippity-clop.
MICROPHONE TYPES
The available gain and large input range of the MS1S allows the use of virtually any type of microphone. True 48V phantom power guarantees the MS1S works with every microphone. The better the mic, the better the MS1S sounds.
Ah, the sound of the thundering hoofs is deafening.
Data Sheet-3
MS1S
MICROPHONE STAGE
Front, Top & Rear Panel Dimensions
6.1"
4 6 2 MIN GAIN MAX 8 SIG OL ON 48V PHANTOM POWER MS1S MIC STAGE
0.15"
100-240 V 50/60 Hz 3 WATTS POWER
6.8"
MS1S RANE CORP.
NORMAL INVERT POLARITY LINE OUT MIC IN PIN 2: (+) PIN 3: (–) PIN 1:
0.35"
Architectural Specifications
The microphone preamplifier shall be a single channel stand-alone unit with a removable IEC power cord. The unit shall accept voltages from 100 to 240 VAC. The input and output shall be fitted with XLR connectors. A polarity inverting switch shall be included. Phantom power of no less than 48 volts shall be provided in compliance with IEC 60268-15 and be controlled by a slide switch with an LED indicator. A gain control shall be provided with 18-66 dB adjustment range. Power, system signal and overload indicators shall be provided. High current cross-coupled active output line driver shall be standard, as well as input RFI filter protection.
The unit shall be a Rane MS1S Micro phone Stage.
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5000 USA TEL 425-355-6000 FAX 425-347-7757 WEB rane.com
Data Sheet-4
All features & specifications subject to change without notice. 1-2014
advertisement
Related manuals
advertisement