Precor AMT 865 Getting Started Guide

This addendum accompanies your equipment documentation and is additional information concerning the heart rate features for your equipment and console.

Important

The heart rate features are intended for reference only. They may not be accurate for every user or at every speed and are not intended for use as a medical device. Holding the heart rate handle touch sensor while exercising at higher intensity may also decrease accuracy of the heart rate reading and is not recommended. Please also read your product documentation and visit:

www.precor.com/en-us/customer-service/faq.

P/N 305324-101 rev A, ENU ©Precor Incorporated | October 2017

EXPERIENCE™ SERIES AMT GETTING STARTED GUIDE

Welcome to a personalized fitness experience for your members

The Experience™ Series cardio line gives operators the proven, reliable performance they count on. Each piece delivers the personalized exercise experience and entertainment choices your members seek. The Adaptive Motion Trainer (AMT) keeps exercisers engaged, challenged, and loyal. For more information about the AMT, visit us at

www.amtfitness.com

.

Get to know Precor equipment

The AMT with Open Stride™ lets the exerciser adjust stride height from 6.8 to 10 inches (17 to 25 cm). Combine this with the AMT’s ability to dynamically adapt the exerciser's stride length from 0 to 36 inches (0 to 91 cm). Open Stride applies to AMT 800 models only. AMT with dynamic stride length applies to AMT 800 and AMT 700 models. The StrideGuide™ diagram illustrates the ratio of stride length to stride height. AMT offers a total body workout in one piece of equipment:    Handlebar positions are optimized for pushing and pulling motions Helps exercisers burn more calories with more enjoyment Monitor stride length with Stride Dial™ The AMT fully engages exercisers of all fitness levels with an infinite range of stride paths to create a uniquely effective low-impact workout, making every workout a personalized experience. Your members get boundless training variety without the need to change machines: improve aerobic and anarobic fitness, as well as strength, coordination, and balance on the AMT.

Get to know Precor cardio workouts

Our instructional videos provide information vital to the safe and effective use of the equipment and can help users, trainers, and operators get the most out of their EFX. A variety of manual and preset programs such as Lose Weight, Be Fit, Get Toned, and Push Performance can help trainers and users meet their goals and build training programs tailored to produce the best possible results. Instructional videos and complete EFX operating instructions are available at

www.precor.com

. Also available at

precor.com

are regularly-updated blog posts with more ideas about fitness routines and advice from trusted industry experts .

AMT Getting Started Guide | P/N 304439-101 rev C , ENU © 2017 Precor Incorporated | June 201 7

CAUTION

TRAINING AND EXERCISING

Before beginning any fitness program, see your physician for a thorough physical exam. Seek advice from your physician to learn the target heart rate appropriate for your fitness level.

Read all safety and operating instructions included with your equipment. For more information, visit us at

www.precor.com

and look for your equipment model number.

Start a workout Step 1

: Place your hands on the fixed side rails and place a foot on each pedal to enter the equipment.

Step 2:

Hold on to the stationary grips in the center.

Step 3:

Start stepping in a vertical motion.

Step 4

: Press

QuickStart

(on screen for touchscreen consoles), or choose a preset workout, then press

OK

to begin.

Step 5:

Adjust the left motion control to change your stride height in one of five levels. You can vary your stride style by lengthening your stride to a maximum of 36 inches.

Step 6:

Adjust the right motion control to select a resistance level, (low for warming up and gradually higher as you start exercising).

Step 7:

Press

Pause

to finish. To dismount safely, hold the fixed hand rails then slowly step off the AMT. Check out our trend-based workouts and Precor product tutorials at

www.precor.com/education

.

P62 Console Installation Guide

WARNING Before you connect any cables to the console, make sure that the equipment is not connected to any external power source or plugged into the wall.

For more equipment information and troubleshooting, visit us at

www.precor.com

.

Cable Connector Type Connector Location

Safety key (TRMs only) TV Six-contact strip, keyed Ethernet (LAN) Data from base unit Power Heart rate sensor F-type coaxial with isolator Eight-contact modular on round black cable Eight-contact modular on flat gray cable Two-contact plug, polarized and latched Four-contact strip, keyed microSD card slot Eight-contact strip Ferrite mount N/A

To attach and wire the console:

1.

Set the console on the rectangular hook at the bottom of the console mount and hold it in place. 5.

Connect the cables board) by routing cables through the larger hole in the mount bracket. as shown below ( is lower 2.

3.

Remove the isolator extender reattach them to the console. Connect the power cable the ferrite mount. , connect the TV coaxial cable to it, then ,after passing it through and wrapping around 6.

Tilt the console back onto the mounting bracket and secure it with the mounting bolts, making sure to fully tighten the bolts. 7.

8.

 9.

10.

  Follow the checklist and set of instructions on the next page to test that the console and equipment are working. Attach the fasteners to reinstall the console rear cover after you finish the tests. To connect to a network: Go to

Settings

>

System Settings

>

Connectivity

. Touch

Network Type

>

Wired (or Wi-Fi)

>

OK

. Touch

Configure

. Select a network from the list and enter your credentials to access that networked. Touch the Back button to return to the Connectivity screen. Your settings will be automatically saved. 4.

Verify the microSD card is securely mounted (see above).

To test that the console and equipment are working:

Use this checklist of procedures for testing and follow each step in order. Install the console based on the information on the other side of this sheet. Verify that the Ethernet patch cables from the floor or wall cannot become caught on the equipment’s moving components (Not applicable for wireless connections). Verify these motion control operations work:   Elevation and speed Resistance (Bikes, EFX, AMT) Scan TV channels, then: 1.

Verify that available channels match the channel list. 2.

Rename the channels if necessary. 3.

Set the default channel, if applicable. Touch

GO

, then verify these operations:       Channel up/down controls Volume up/down controls Channel changes on the channel list USB connection (only for charging a personal media player and updating Preva software) Headphone jack STOP button and emergency stop lanyard (TRM only) Verify that the heart rate display works: 1.

Begin exercising on the equipment and grasp both touch-sensitive handlebars. The heart icon flashes while the heart rate is read. You must maintain contact with both metal plates on each handlebar to ensure an accurate reading. Within ten seconds, your heart rate number appears in the HEART RATE (HR) display. 2.

Perform the following checks if a number does not appear: a.

Verify that the HR cable is properly connected. b.

Repeat the test with a different person. In rare instances, it may not work properly for a few individuals. c.

Repeat this test using a chest strap or a wireless pulse simulator. You’ll get better results than if you grasp the touch-sensitive handlebars. DO NOT hold onto the handlebars during the reading or you’ll override the HR results. Verify the microSD card is securely inserted. Verify the TV coaxial cable is securely installed by using a 7/16 open wrench to fully tighten the cable to the console. Verify IP connectivity. Go to

System Settings

>

Connectivity

. The IP address field should be populated (10.15.80.90, for example). Then, to register the equipment, make sure you have this info:  Location code   Precor technician account name and password Serial number from the base  Friendly name assigned to the equipment by the facility (Example: Equipment Type-Floor-Row-Number) To complete registration for Preva-networked facilities: 1.

2.

3.

Enter the Preva server name (na.preva.com for all sites). Enter the assigned account name and password. Follow the onscreen instructions to register the product. Ask the facility’s Preva administrator to log on to Preva Business Suite and confirm that all P82-based equipment appears there. P62 Installation Guide | P/N 304148-101 rev A, ENU ©Precor Incorporated | August 2016

P62 CONSOLE GETTING STARTED GUIDE

Welcome to a personalized fitness experience for your members

The intuitive high-definition touchscreen, easy-to-reach single or dual motion controls, and built-in fitness tutorials makes the P62 Console a unique fitness experience for your members and trainers.

Set up the console

The P62 console has a built-in Administrator account for owners. The Settings menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment. An

Administrator

uses a password (see below) to access and configure the console settings to improve an exerciser's workout and benefit the facility.

To change system settings:

1.

2.

3.

4.

Press and hold

Volume Down

. Press Channel in the following order:

Channel Up Channel Down Channel Down Channel Up

Enter the password:

5 6 5 1 5 6 5

Touch

OK

. The System Settings banner appears.

Setting

About

Information

Displays serial number and event log. Equipment Use Gathers data on individual and cumulative equipment use System Settings Connectivity: Determines network type (Wired and Wi-Fi) and IP address. TV settings: Sets up channels and close captions Workout limits: Sets limits on equipment use during peak hours, maximum treadmill speed, or maximum pause time. For complete console operating instructions and troubleshooting, visit us at

www.precor.com

. P62 Console Getting Started Guide | P/N 304240-101 rev A, ENU ©2016 Precor Incorporated | August 2016

TRAINING AND EXERCISING

Get to know the P62 Console

The P62 Console features either single- or dual-motion controls, uses an LCD touchscreen with an embedded TV tuner, and is Preva™ Network Capable.

No. Function

Pause Incline or stride height 1 indicator

No. Function

Channel up/down Mute Intensity or resistance indicator Volume up/down 2 Audio jack Mobile device charger * Stride height indicator for AMT only ** Incline indicator only on the dual-motion control. The motion control(s) are located right below the indicator.

Start exercising

Ready to up your game and give your clients great workouts and training programs? Take advantage of Precor’s product tutorials, best-in-class training resources, and content libraries — which we refresh regularly (select regions only) — on

www.precor.com

.

CAUTION Before beginning any fitness program, see your physician for a thorough medical exam. Ask your physician for the appropr target heart rate for your fitness level.

To start a workout:

Touch

Quick Start

to launch the Manual Program. Calculations, such as calories used, are based on a 170-lb (77 kg), 40-year old individual. Your clients can complete a workout using this program with the default values, or you can change workout settings to suit the training program you set up for them.

To start a featured workout:

The Featured Workout appears on the Welcome Screen and changes daily. Touch

GO

on the Featured Workout screen.

To start a preset workout:

Preset workouts are a great way to tailor your client’s workouts to their fitness goals, stay challenged, and add variety to their sessions. These workouts are arranged in the following groups:

Manual, Heart Rate, Interval, Weight Loss

(Fat Burner on Climbers)

, Variety, and Performance

. 1.

2.

Touch

Workouts

, select a workout, then touch

GO

. At the end of a workout, a summary screen displays the average heart rate and accumulated metrics achieved during a workout. Save the workout for replay later (for Preva accounts only).

Monitor your heart rate Chest straps

A chest strap provides the best heart rate monitoring results. When you wear a chest strap during a workout, the heart rate features appear on the screen. To receive an accurate reading, the chest strap must be in direct contact with your skin.

Touch heart rate feature

To use the heart rate feature, use both hands on the grips and make sure your hands are moist (not dry). Avoid grasping the sensors too tightly.

Equation 1: Englis h

Experience™ Series Adaptive Motion Trainer® (AMT®)

Assembly Guide

English Français Deutsch

日本語 中文

Español Português

2

AMT Assembly Requirements

Start assembling the AMT while it is still on the pallet. Remove the AMT from the pallet when instructed to so in this guide. Follow the steps in the order listed in this assembly guide. For more product information, visit us at

www.precor.com.

WARNING At least two people are required to assemble the equipment. DO NOT attempt assembly by yourself.

Assembly requirements

Important

Before you fully tighten a fastener, check that its head is flush with the surface of the equipment. If not, cross-threading may have occurred. DO NOT attempt to rework the assembly as more damage to the equipment will occur. Instead, contact Customer Support at www. precor.com

We recommend you: • • • • Assemble the equipment close to where you plan to use it. Assemble the equipment on a solid, flat surface, so that it remains level and stable. Locate the equipment at least 19.7 inches (0.5 meter) away from walls or furniture on either side of the equipment, and 19.7 inches (0.5 meter) away from objects behind or in front of the equipment. DO NOT move the equipment without assistance. 3

Required tools

• • • • • • • #2 Phillips screwdriver Rubber mallet 7/16-inch open-end wrench SAE standard socket set Wire cutter Two #1 Phillips screwdrivers Torque wrench (including a 3/16-inch hex wrench bit)

Hardware kit

Component

Nylon lock nuts (5/16 inch) Hex head bolts (5/16-inch x 1-inch) Hex head bolts (5/16-inch x 3 1/2 inch)

Quantity

6 4 6 Bolt sleeve Flat Washer (5/16-inch) 2 6

Component

Screw (#10 x 1 1/4-inch) Flat head hex drive screws (1/4-inch x 5/8-inch)

Quantity

10 5 End caps Conduit (optional) 2 1 4

Begin assembly

Important

The side arm supports are shipped with foam blocks inserted in one end. These blocks prevent fasteners from falling into the supports. DO NOT remove the foam blocks or push them down into the supports.

To attach the upper side arm supports:

1.

Place the upper end of the right-hand support against the right-hand side arm and insert two screws (with washers attached) into the two holes underneath the side arm support bracket (see Figure 1 ). Partially tighten. 3.

Attach the bolt using the nut (see Figure 3). Partially tighten.

Important

Insert the bolt into the inside of the side arm and attach the nut to the outside or the side covers will not fit.

Figure 1

2.

Slide one washer and one sleeve over a bolt and insert it into the screw hole on the inside of the right-hand side arm (see Figure 2).

Figure 3

4.

Repeat Steps 1 through 3 to attach the left-hand side arm support.

Figure 2

5

To attach the lower side arm supports:

1.

Place the two side arm supports against the center support and insert a narrow screwdriver through the middle holes of each side arm and the center support to keep them aligned (see Figure 4). 5.

Remove and throw away the two #10 x 3/4-inch Phillips head screws securing the upper back corner of the inner plastic molding to the end of the right side arm.

Figure 4

2.

Slide a washer over each of the four bolts and then, from the opposite side of the center support, insert the four bolts and attach a nut to each bolt. Partially tighten the fasteners (see Figure 5).

Figure 6

6.

Fit the right-hand inner and outer side arm covers to the right side arm. Insert five screws

Note

, then tighten them to 8 to 12 in-lb (1 to 1.35 N-m) using a #2 Phillips screwdriver (see Figure 7). Alternatively, tighten the screws until the two side arm covers are in full contact, then turn the screws an additional quarter turn.

Figure 5

3.

4.

Tighten the side arm supports to 160 in-lb (18 N-m) of torque. Using a 9/16-inch open-ended wrench, loosen the jam nuts and extend the adjustable feet on the side arm supports until they touch the floor; then remove the spacer block from under the back end of the AMT.

Figure 7

7.

Repeat Steps 4 and 5 to attach the left side arm. 6

Remove the AMT from the pallet

After the side arm supports are secured, move the AMT off of its shipping pallet to the location where it will be used.

CAUTION DO NOT move the AMT off its shipping pallet without assistance. DO NOT apply any weight to the side arms of the AMT until the side arm supports have been installed. To avoid unnecessary movement of the foot plates, DO NOT position the handlebars until instructed to do so.

To move the AMT from the pallet:

1.

Remove and discard the two fasteners securing the front frame tube of the AMT to the shipping pallet (see Figure 8). 2.

3.

4.

Lift the back end of the center support and roll the AMT forward onto the floor while your assistant stabilizes its front end and guides it off the shipping pallet. Move the AMT to its intended location. Insert the end caps into the front frame tube, and if needed, use a rubber mallet to tap them into place.

Figure 8

7

Remove the access covers

Removing the front and side access covers provides sufficient space to install the console cables.

Note

If you are installing a non-touchscreen console without a Personal Video System (PVS) or accessory cap, you do not need to remove the access covers.

Important

Remove any ties or other materials that hold the side arms in place before the supports are installed.

To remove the access covers:

1.

Lift the gasket upward and remove it from the center support (see Figure 9). 2.

Extend a finger through the gasket opening and under the front edge of the top cover. While pressing upward on the top cover, use the heel of your hand to tap below its front edge and release it (see Figure 10). Repeat this step to release the other side of the top cover.

Figure 9 Figure 10

3.

4.

5.

6.

While holding up the front edge of the top cover, use the heel of your other hand to tap just below the back edge of the cover. Lift the cover up and out of the way. Remove the two #10 x 3/4-inch screws from the bottom corners of the front cover assembly. Gently press in on each of the side covers, just behind the front edge and about 8 1/2 inches from the bottom, while pulling the front cover assembly forward to disengage it.

Note

Each side cover has a small triangular mark to show you where to press. Move the front cover assembly forward and slightly upward to remove it. 8

Rewire the AMT for a touchscreen console

DANGER DO NOT attempt to connect electrical power until all assembly procedures are complete and the console is properly installed.

Retrieve the following parts from the console package: TV (coax) coupler Ethernet (CAT 5) coupler and cable Cable, and the console power cable

Important

Make sure all cables pass through all of the cable clips and DO NOT allow any of the cables to hang near moving parts.

Note

In the following steps, pass the console power cable through the opening first, followed by the TV cable. Pass the remaining cables through in order of connector size (see Figure 11).

Thread the cables for each part as follows:

1.

TV connection a.

b.

: Install the TV (coax) coupler, star washer, and nut, into the jack plate at the lower end of the AMT and tighten (see Figure 12). Connect the TV cable to the inside end of the TV cable coupler. Tighten the connector using a 7/16-inch open-end wrench. 2.

Ethernet connection a.

(see Figure 12). : Attach the Ethernet coupler into the jack plate at the lower front of the AMT b.

Plug the Ethernet cable into the coupler. 3.

Console connection a.

b.

: Plug the console power cable into the jack plate (see Figure 12). Slide the quick-disconnect terminal on the grounding lead of the power cable over the grounding terminal on the equipment frame.

Figure 11 Figure 12

9

To continue the wiring:

1.

2.

Pass the ends of all cables through the opening in the top of the cable channel and secure them in the cable clips. Route the cables through the cable clips next to the front flywheel, through the topmost cable clip on the main frame, and up to the center support (see Figure 13). 3.

Remove the tie from the base data cable. Group that cable with the others and thread them upward through the center support and out through the center opening in the console mount, making sure that the heart rate sensor cable extends out of the opening as well.

Important

Store excess cable inside the center support. DO NOT allow cables to hang loosely inside the body of the AMT.

Figure 13

To complete the console installation, refer to the

Installation Guide

included in your console box. 10

Route cables under the rear pedestal (optional)

When the AMT faces away from the cable raceway, use the conduit included in the hardware kit to route the Ethernet, TV, and power cables underneath the center of the AMT and through its rear pedestal.

To use the conduit:

1.

2.

3.

Lay out the cables so that they pass directly under the center support of the AMT and place the conduit on the floor directly behind the center support. Insert the cables, one at a time, into the slot at the top of the conduit.

Important

DO NOT clip or tie the segments of the cables that you insert into the conduit.

Lower the rear pedestal over the back frame tube and the side arm supports. The pedestal should sit flat on the floor and with the conduit completely inside of it (see Figure 14).

To replace the access covers:

4.

Guide the front cover around the arms so that the tabs at the bottom corners are inside the two side covers. Slide it into place until the latches on the side covers click into place (see Figure 15). 5.

Figure 15 Figure 14

6.

7.

8.

Reattach the bottom corners of the front cover using two #10 x 3/4-inch screws. Fully tighten.

Important

In the following step, DO NOT apply excessive force to seat the cover.

Position the rear edge of the top cover so that the clips on the top and back covers are engaged securely. Using the heel of your hand, gently snap the front edge of the top cover into place. Wrap the gasket around the center support below the heart rate sensor grips, then fit it into the top cover making sure the edges of the seal are flush with the top cover (see Figure 16).

Figure 16

11

Position the handlebars

During shipment, the AMT is packed with its handlebars reversed. Two set screws are threaded into each handlebar. The plastic boots that eventually cover the screws are positioned just above them on the handlebars.

To position the handlebars for use:

1.

Remove the two set screws from one handlebar (see Figure 17). 3.

4.

5.

Reinsert the two set screws. Leave the screws partially tightened until you have adjusted both handlebars. Repeat Steps 1 through 3 to position the other handlebar. Adjust the positions of both handlebars outward as much as possible. Both handlebars should be at equal angles to the body of the AMT and angled slightly outward (see Figure 19).

Figure 17

2.

Rotate the handlebar exactly one half turn (180°) (see Figure 18).

Note

frame. When the handlebar is positioned correctly, it bends slightly outward. The screw holes in the handlebar should also line up with those on the AMT

Figure 19

6.

Rotate one of the plastic boots so that it aligns with the surface below it, then press the boot downward to secure it in place (see Figure 20). Repeat this step to position the other plastic boot.

Figure 18 Figure 20

12

Level the AMT

It is important to level the AMT properly every time you move it.

CAUTION To eliminate movement, make sure the adjustable feet are in contact with the floor. Also, make sure that the AMT sits on a flat surface. Adjusting the feet of the AMT cannot compensate for extremely uneven surfaces.

To level the AMT:

1.

2.

3.

Try to rock the AMT while standing on one of its foot plates and grabbing the opposite handlebar. If there is any movement, with assistance, tip the AMT to one side to locate the adjustable feet. Using a 9/16-inch open-ended wrench, move the jam nuts away from the side arm supports and toward the adjustable feet. Correct the height of each adjustable foot as follows (see Figure 21):

Important

To allow the rear pedestal to fit properly, the adjustable feet must extend at least 2 inches (5 cm) below the side arm supports. Extend the feet before you remove the spacer block (as described in

To add the side arm supports

), to ensure that they are positioned correctly.

4.

5.

6.

When you finish adjusting the equipment, recheck for movement and readjust as necessary. Using the 9/16-inch open-ended wrench, move the jam nuts upward until they contact the side arm supports and fully tighten them. Align the rear pedestal over the back frame tube and the side arm covers, then press the pedestal into place (see Figure 22).

Figure 22

If you want to ...

Raise the front end of the AMT Lower the front end of the AMT

Figure 21

Then turn the adjustable feet …

Counterclockwise Clockwise 13

14

15

AMT Assembly Guide | P/N 304438-101 rev B, ENU ©2016 Precor Incorporated | October 2016

         

                         

  

NOTES

NOTES

Cardio Safety Regulatory Warranty | P/N 305035-101, rev B , ENU

Cardio Equipment Quick Reference

Maintenance Guide

Cardio Equipment Quick Reference Maintenance Guide

For

complete

maintenance and cleaning information, visit us at

www.precor.com

. For torque settings, review the product Assembly Guide included with your equipment, or go to

www.precor.com

for more information.

Important

The owner is responsible for maintaining Precor equipment in their facility based on the recommendations below and any accompanying material.

Weekly Maintenance Tasks

Cleaning procedures

Use a lint-free cloth dampened with water or an approved cleaner in the procedures below.      Clean the floor under the equipment.

DO NOT lift and hold equipment while vacuuming.

When the floor is completely dry, restore power and return the equipment to its level position. Clean all surfaces of the frame and plastic components.

Keep excess moisture away from electronic components to prevent electrical shock or damage, and dry completely.

Use a soft nylon scrub brush to clean grooves and textured surfaces on foot contact locations. On LCD- or PVS- equipped equipment, clean the screen using only a diluted solution of one part 91% isopropyl alcohol to one part water on a damped, lint-free cloth. Dry completely.

For elliptical and treadmill only

Clean debris from all wheels (for treadmill and elliptical) and CrossRamp® (for elliptical). Dry completely.

Other weekly maintenance tasks for all equipment

    Unplug the power cords from any equipment or entertainment devices plugged into a wall outlet. For treadmill: Turn off the circuit breaker. Verify all equipment feet sit squarely on the floor, and adjust if necessary to ensure the equipment does not wobble. Verify that the power cords are not damaged or pinched. Plug in the equipment, turn it on, and verify the following features are performing properly: • Handheld Heart Rate (HHHR)   • Incline, Speed, and Resistance controls

Elliptical only

• • Elevate the equipment to its maximum incline. Clean the ramp (no disassembly required). Debris build-up will shorten the life of the product.

Treadmill only

• Verify the safety lanyard works. • Emergency Stop Button 2

• • Elevate the equipment to its maximum incline. Follow the procedures,

Check the

a

lignment of the running belt

and

Adjust the running belt

, in this Guide.

Monthly Maintenance Tasks

Perform all checks listed under Weekly Maintenance Tasks

plus

the following:

For all equipment

  Verify the Wireless Heart Rate feature is performing properly by following the procedure, Verify that the heart rate feature works, in this Guide. Remove plastic enclosures from the drive compartments and remove any lint or debris, and then do the following in order:       • • • • • Clean the drive belts and pulleys with a small wire brush. Vacuum out any debris, being careful not to bring the vacuum cleaner nozzle too close to any circuit board. Precor recommends you use a vacuum that protects against static buildup. Inspect visible welds, frame, and wire connections. Check all fasteners for proper tightness and torque.

Treadmill, elliptical, and AMT only

Clean and lubricate the lift motor screw with an approved grease such as SuperLube® with Teflon or Mobil 1™ synthetic grease, if necessary. • •

Treadmill only

Verify the power cord clamp is securely installed. Replace all removed plastic enclosures.

Treadmill only

Visually inspect the running deck and belt. Make sure the deck and belt are in good condition and replace the belt, if necessary.

Elliptical only

• Verify that the wheels run smoothly on the CrossRamp®. • • Check all wheels for wear or cracks. Lift the badge plate from the bottom front to loosen the rubber gasket. Remove the gasket (at the split) from the back of the display mount. Clean debris then replace the gasket from back to front, aligning the tabs as you go. DO NOT pull the gasket ring off before removing the badge plate first.

AMT and climber only

Inspect support belts and pulleys for wear or damage. Check torque on belt clamps.

All equipment except treadmill

Verify pedals move smoothly and freely in all directions.

Bikes only

Verify that the seat moves through the entire adjustment range and that the position latch works correctly.

For treadmill only

Clean the underside of the running belt and top deck by following the procedure, Clean the running belt and deck in this Guide or visit us at

www.precor.com

. 3

Quarterly Maintenance Tasks

Perform all checks listed under

Weekly Maintenance Tasks

and

Monthly Maintenance Tasks, plus

the following:       Check tension of the running belts and adjust if necessary. Inspect belts for excessive wear. Perform software diagnostics and check LED function.

AMT only

Inspect the gas spring shock. Contact Precor Customer Support if you have questions.

EFX only

Check the belt tension.

Bikes only

Verify that the seat is secure and stable.

Climber only

Inspect the tension springs and pedal stops for damage and function.

Semi-Annual Tasks

 

All equipment except treadmill

Verify battery voltage.

Treadmill only

Lubricate the lift motor screw. 4

Error Codes

The following is a list of error codes and how to resolve the issue:

Error Codes

00-09, 11-16, 50 10, 20-23, 26-28, 32, LS, ERR, E2, E4 40, 42, 44-46 80-83 30, 31 62, 70-77

Action

Turn the equipment off and on. Repeat twice. If the message still appears, contact a Precor certified service technician.

Equipment

AMT, elliptical, treadmill, RBK, UBK, and CLM Contact a Precor-certified service technician. AMT, elliptical, treadmill, RBK, UBK, and CLM Logs error and displays code to user. User can continue the workout without interruption. AMT, elliptical, treadmill, RBK, UBK, and CLM Turn the equipment off and on. Repeat twice. If the message still appears, contact a Precor certified service technician. AMT, elliptical, treadmill, RBK, UBK, and CLM Displays the error on the console to the user. Restart the equipment or reset the E-STOP to use. Logs as a fatal error. Contact a Precor certified service technician. AMT, elliptical, treadmill, RBK, UBK, and CLM AMT only 78 79 17-20, 25, 85-88 29 33, 35-37, 60, 62 Display the message, "Belts must be changed soon", in place of the standard banner text. Logs the error and allows the user to begin the workout. Contact a Precor certified service technician. Displays the message, "Belts change required", in place of the standard banner text. No workout can be started. Contact a Precor-certified service technician. AMT only AMT only Turn the equipment off and on. Repeat twice. If the message still appears, contact a Precor certified service technician. treadmill only Displays the error on the console to the user and pauses the workout. The treadmill speed MUST return to 0 before starting again. Logs the error. Displays the error on the console to the user. Restart the equipment or reset the E-STOP to use. Logs as a fatal error. treadmill only treadmill only 5

Verify that the heart rate display works To verify that the heart rate display is operational:

1.

Begin exercising on the equipment and grasp both touch-sensitive handlebars. The heart icon flashes while the heart rate is read. You must maintain contact with both metal plates on each handlebar to ensure an accurate reading. 2.

Within ten seconds, your heart rate number appears in the HEART RATE display. If a number does not appear, perform the following checks: • • • Verify that the HR cable is properly connected. Repeat the test with a different person. In rare instances, it may not work properly for a few individuals. Repeat this test using a chest strap or a wireless pulse simulator. You’ll get better results than if you only grasp the touch-sensitive handlebars. DO NOT hold onto the handlebars during the reading or you’ll override those results.

Moving the equipment

The equipment is very heavy. If you plan to move it to a new location, obtain the help of an adult assistant and use proper lifting techniques. If the equipment includes roller wheels on one end, use the wheels to reduce the load on yourself and your assistant.

To move the elliptical (EFX):

 Precor recommends using a four-wheeled dolly to move the EFX.

To move the AMT:

1.

Disconnect, unplug, and remove all external connections (television, Ethernet, and power). 2.

3.

4.

5.

Lift the rear platform molding to remove it. Lift the rear foot supports to tip the AMT forward onto its roller wheels. Push the AMT into its new location. Lower the rear foot supports to the floor, then reattach the rear platform molding.

To move the treadmill:

A treadmill in an inclined position is easier to move.

Important

The plastic end caps on Precor treadmills are designed specifically for lifting. Working with your assistant, place a hand under each side of the end cap. Then, using proper lifting techniques, lift the rear of the treadmill so that it rolls on its front wheels.

6

To put the treadmill into an inclined position for moving:

1.

Press

GO

on the console. 2.

Increase the incline to Level 4 or more. 3.

4.

While the treadmill is running, turn the main power switch to OFF. Disconnect the treadmill’s power cord.

Check the alignment of the running belt (treadmill only) Important

Failure to align the belt may cause the belt to tear or fray, which is not covered by the Precor Limited Warranty.

Proper alignment allows the belt to remain centered and ensures smooth operation. Realigning the belt takes a few simple adjustments. If you are unsure about this procedure, contact Precor Customer Support.

CAUTION DO NOT adjust the running belt when someone is standing on it.

To check the alignment of the running belt:

1.

Make sure that the running surface is as level as possible. If necessary, adjust the rear feet to level the treadmill. 2.

3.

4.

5.

6.

7.

Note

Adjusting the rear feet cannot compensate for extremely uneven surfaces. If you cannot make the running surface level and stable, move the treadmill. Turn the treadmill on. Stand beside the treadmill (not on it), and press

GO

or

Quick Start

on the console. If necessary, enter the safety code by pressing the number keys in sequence. The running belt starts automatically after a 3-second countdown appears on the console. Press

SPEED UP

until the console shows a speed of 3 mph (5 kph). Observe the belt from the rear of the treadmill for a few minutes. The belt should remain centered along the running bed. If it drifts off center, you need to adjustment it.

CAUTION If you hear any rubbing or the running belt appears damaged, press the red STOP button immediately and contact Precor Customer Support.

Press

STOP

to stop the belt and turn the treadmill off. 7

Adjust the running belt (treadmill only)

If you are unsure about adjusting the running belt, contact Precor Customer Support.

CAUTION Take special care when aligning the running belt. The treadmill will not stop immediately if an object becomes caught in the belt or rollers. Turn OFF the treadmill while adjusting or working near the rear roller. DO NOT wear loose clothing or allow your hair to hang loose during this procedure. DO NOT adjust the running belt when someone is standing on it. Keep your fingers and any other object clear of the belt and rollers, especially in front of the roller and behind the deck.

Important

Make all belt adjustments on the adjusting bolts at the rear corners of the treadmill using the hex key provided, and DO NOT turn either bolt more than ¼ turn before checking the alignment of the running belt again. Overtightening the adjusting bolts can damage the treadmill.

To adjust the running belt:

1.

Locate the adjusting bolt in the right side end cap at the rear corner of the treadmill (Figure 1). 2.

Use the hex key to tighten the adjusting bolt in the direction that the belt is shifting. Turn the bolt ¼ turn clockwise.

If the belt ...

Then ...

Figure 1

3.

Continues to shift in the original direction Turn the

same

adjusting bolt an additional ¼ turn clockwise. Starts to shift in the opposite direction Turn the

same

adjusting bolt ⅛ turn or less counterclockwise. Recheck the belt position as described in

Check the Alignment of the running belt

.

Note

If the belt slips after you have adjusted it, tighten the adjusting bolt evenly, ¼ turn at a time, until the slipping stops. DO NOT overtighten the belt. 8

Clean the running belt and deck (treadmill only)

Before you begin the cleaning procedure, check that the safety stop key works correctly.

CAUTION DO NOT stand or allow others to stand on the treadmill running belt during this procedure.

To make sure the safety stop key works:

1.

Stand to one side of the treadmill. 2.

3.

4.

5.

6.

Make sure that the stop key lanyard is hanging straight down and is not wrapped around the handle bars. Press

Quick Start

and wait for the running belt to begin moving. Press the safety stop key. The running belt should stop immediately. When it stops, reset the safety stop key.

CAUTION If the running belt does not stop, turn off the treadmill power using the On/Off switch at the front of the treadmill and unplug the power cord. The treadmill must remain out of service until the stop switch is repaired. Place an "out of order" sign on the treadmill and contact Precor Customer Support.

Turn the treadmill power switch to Off. The On/Off switch is located at the front of the treadmill.

To clean the treadmill belt and deck:

1.

Make sure the treadmill is turned off. 2.

3.

4.

Take a clean, dry cotton towel that is at least 36 in. (2 m) long and fold it in half lengthwise. Lift the running belt up and push the towel under the belt. Make sure a few inches of towel extend over the deck trim on each side. Push the towel forward to the front of the machine so it is located beneath the safety stop key. 5.

6.

7.

Turn the power switch to

On

.

Figure 2

Step onto machine by standing on the side rails and attach the stop key lanyard to your clothes.

Important

DO NOT stand on the running belt at any time.

Stand firmly on both ends of the towel keeping your feet off of the treadmill running belt (Figure 2). Brace yourself using the handlebars or side hand rails. 9

8.

9.

Press

Quick Start.

Important

You have three seconds before the treadmill belt begins to move. Hold the handlebars or side hand rails to help maintain balance.

The treadmill will run at 1 mph. Allow the treadmill to run for one minute while keeping the towel firmly in place.

CAUTION Press the safety stop key if the towel becomes loose to prevent it from being pulled into the treadmill’s rollers. DO NOT adjust the treadmill’s speed or run it higher than 1 mph.

10.

After one minute, press

Stop

to stop the treadmill belt. 11.

When the belt is completely stopped, remove the stop key lanyard from your clothing, and step off the treadmill. 12.

Turn the treadmill power switch to

Off

. 13.

Grasp both sides of the towel and run it up and down the length of the belt several times to clean the top of the deck before removing it from beneath the belt. 14.

Turn the power switch to

On

and return the treadmill to normal use. 10