TR33 Remote Control
SPECIFICATION and INSTRUCTION SHEET
DESCRIPTION: One Ceiling Fan Only, 3 Speed Remote Control
ELECTRICAL SPECS: 1A, 120V, 60Hz Ceiling Fan
FAN MODEL USED: See Catalog or visit our website www.fanimation.com for more
information
How to Wire and Operate Your TR33 Remote Control
NOTE: If fan or supply wires are different colors than indicated,
have this unit installed by a qualified electrician.
▲WARNING
Remote Transmitter
Unit Detail
Receiver Unit Detail
Figure 1a
Figure 1b
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
4. Installing Receiver in Hanger Bracket:
• Slide remote Receiver into the Hanger Bracket (Figure 2).
• Connect wires as indicated: (Figure 3)
– Green Ceiling Plate and Motor Bracket wires to BARE
(ground) wire.
– BLACK Receiver Unit wire (AC IN L) to BLACK supply wire.
– WHITE Receiver Unit wire (AC IN N) to WHITE supply wire.
– WHITE Receiver Unit wire (TO MOTOR N) to WHITE fan wire.
– BLACK Receiver Unit wire (TO MOTOR L) to BLACK fan wire.
• Position all connected wires and receiver antenna to
allow installation of motor assembly.
• Reinstall ceiling canopy using canopy screws.
• Restore electrical power.
Ceiling
Bracket
(Open End)
Receiver Unit
NOTE: Receiver wires omitted for clarity.
Figure 2
GRN from motor bracket
GRN from ceiling plate
1. Setting the Code: The remote unit has 16 different
code combinations. To prevent possible interference from
or to other remote units such as garage door openers, car
alarm or security systems, simply change the combination
code in your transmitter and receiver. To set the code,
perform these steps.
2. Transmitter: remove battery cover. Press firmly below
arrow and slide battery cover off. Slide code switches to
your choice of up or down position. Factory setting is all
up. Do not use this position. With a small screwdriver or
ball point pen slide firmly up or down (Figure 1a). Replace
battery cover on the transmitter.
3. Receiver: Slide code switches to the same positions
as set on your transmitter (Figure 1b).
GRN or BARE GROUND
WH-TO MOTOR N
BLK-TO MOTOR L
WH-AC IN N
BL-AC IN L
BLK-ANT
120 VAC SUPPLY
(User Supplied)
Figure 3
▲WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate
fan until the blades is in place. Noise and fan damage
could result.
5. Operating & Using Remote Transmitter (Figure 4):
Install two piece of 3 volt battery (If not using for long periods of
time, remove battery to prevent damage to transmitter). Store the
transmitter away from excess heat or humidity.
• HI Push Button – high fan speed
• MED Push Button – medium fan speed
• LOW Push Button – low fan speed
• OFF Push Button – fan off
• Center Button – no function
3V, CR2032
BATTERY
2 PCS
Figure 4
NOTE: Set fan switch to high speed before using the remote control.
You can now use your speed control to select any of the 3-speeds plus
OFF.
How to Install Your Remote Control (Option #1)
1. Unthread two screws from the wall switch plate.
(Figure 1)
2. Install the control bracket with two #6-32x 3/4” screws.
And push the four plastic plug to cover the screw holes.
(Including in the control).(Figure 2)
Figure 1
Figure 2
How to Install Your Remote Control (Option #2)
1. Unthread two screws from the wall switch plate.
(Figure 1)
2. Install the control bracket with two #6-32x 1” screws.
And push the four plastic plug to cover the screw holes.
(Including in the control).(Figure 2)
Figure 1
Figure 2
How to Install Your Remote Control (Option #3)
1. Drill the two 1/4” holes in wall and use the M6 plastic
anchor pushed into the holes. Install the control bracket
with two #3- 1” self tap screws. Push the four plastic plug
to cover the screw holes. (Including in the control).
(Figure 1)
Figure 1
10983 Bennett Parkway
Zionsville, IN 46077
(888) 567-2055 • FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Visit Our Website @ www.fanimation.com
Copyright 2013 Fanimation
2013/09
">
