Zyxel B-220 B-220 User's Guide
Reklaam
Reklaam
ZyAIR
Wireless LAN Utility
User's Guide
Version 2.00 September 2003
ZyAIR Wireless LAN Utility
Copyright
Copyright ©2003 by ZyXEL Communications Corporation
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved.
Disclaimer
ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patents' rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice.
Trademarks
Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners.
ZyAIR Wireless LAN Utility
ZyXEL Limited Warranty
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to one (1) year from the date of purchase. During the warranty period and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.
NOTE
Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind of character to the purchaser. To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material Authorization (RMA) number. Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country.
Online Registration
Register online at www.zyxel.com
.for free future product updates and information. ZyXEL Limited Warranty iii
ZyAIR Wireless LAN Utility
Information for Canadian Users
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operation and safety requirements. The Industry Canada does not guarantee that the equipment will operate to a user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. For their own protection, users should ensure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution
Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate.
Note
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of Industry. iv Information for Canadian Users
ZyAIR Wireless LAN Utility
Federal Communications Commission (FCC) Interference Statement
The Wireless LAN Adapter has been tested to the FCC exposure requirements (Specific Absorption Rate). The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio/television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.
Notice 1
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Caution
1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter
Certifications
Refer to the product page at www.zyxel.com. FCC Statement v
ZyAIR Wireless LAN Utility
Customer Support
When contacting your Customer Support Representative, please have the following information ready: Product model and serial number. Warranty Information. Date you received your product. Brief description of the problem and the steps you took to solve it. REGULAR MAIL METHOD LOCATION WORLDWIDE E-MAIL SUPPORT/SALES [email protected]
+886-3-578-3942 www.zyxel.com
www.europe.zyxel.com
ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu 300, Taiwan [email protected]
+886-3-578-2439 [email protected]
+1-800-255-4101 NORTH AMERICA [email protected]
ftp.zyxel.com
SCANDINAVIA GERMANY [email protected]
+45-3955-0700 [email protected]
+45-3955-0707 [email protected] [email protected] +49-2405-6909-0 +49-2405-6909-99 www.zyxel.de ZyXEL Communications A/S, Columbusvej 5, 2860 Soeborg, Denmark ZyXEL Deutschland GmbH. Adenauerstr. 20/A2 D-52146 Wuerselen, Germany Customer Support vii
ZyAIR Wireless LAN Utility
Table of Contents
Table of Contents ix
x ZyAIR Wireless LAN Utility
Table of Contents
ZyAIR Wireless LAN Utility
List of Figures
List of Figures xi
ZyAIR Wireless LAN Utility
List of Tables
xii List of Tables
ZyAIR Wireless LAN Utility
Preface
Congratulations on the purchase of your new ZyAIR!
About This User's Guide
A practical and comprehensive tool, this manual provides information about the ZyAIR Wireless LAN Utility. Familiarize yourself with the
Syntax Conventions
listed for better and faster understanding. This guide is for both ZyAIR B-120 and B-220 that use the ZyAIR Wireless LAN Utility for configuration, thus the model name shown in the screens may vary from what you actually purchased.
Syntax Conventions
• “Type” or “Enter” means for you to type one or more characters. "Select" or "Choose" means for you to use one of the predefined choices. • Window and command choices are in in
Bold Arial
font.
Bold Times New Roman
font. Predefined field choices are • The ZyXEL ZyAIR wireless adaptor is referred to as the ZyAIR in this guide. • The ZyAIR Wireless LAN Utility may be referred to as the ZyAIR Utility in this guide.
Related Documentation
Support Disk Refer to the included CD for support documents and device drivers. Quick Installation Guide Our Quick Installation Guide is designed to help you get your ZyAIR up and running right away. It contains a detailed easy-to-follow connection diagram and information on installing your ZyAIR. ZyXEL Glossary and Web Site Please refer to www.zyxel.com
for an online glossary of networking terms and additional support documentation.
User Guide Feedback
Help us help you! E-mail all User’s Guide-related comments, questions or suggestions for improvement to [email protected] or send regular mail to The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 300, Taiwan. Thank you! Preface xiii
ZyAIR Wireless LAN Utility
Chapter 1 Wireless Network Basics
This chapter gives you an overview of what a wireless network is, its advantages and applications.
1.1 Introduction
A wireless LAN (WLAN) provides a flexible data communication system that you can use to access various services (navigating the Internet, email, printer services, etc.) on the wired network without additional expensive network cabling infrastructure. In effect, a wireless LAN environment provides you the freedom to stay connected to the wired network while moving in the coverage area.
1.2 Benefits of a Wireless LAN
Access to network services in areas otherwise hard or expensive to wire, such as historical buildings, buildings with asbestos materials and classrooms. Doctors and nurses can access a complete patient’s profile on a handheld or notebook computer upon entering a patient’s room. It allows flexible workgroups a lower total cost of ownership for networks that are frequently reconfigured. Conference room users can access the network as they move from meeting to meeting- accessing up-to-date information that facilitates the ability to communicate decisions “on the fly”. It provides campus-wide networking coverage, allowing enterprises the roaming capability to set up easy-to-use wireless networks that transparently covers an entire campus.
1.3 Applications
Unlike wired networks, you can set up wireless networks in two different modes: infrastructure and ad-hoc. Set up your wireless network depending on your network needs. The following sections describe each network mode.
1.3.1 Ad-hoc
An ad-hoc network consists of two or more computers communicating with one another through the wireless network. No access points (APs) or existing wired networks are needed. An access point acts as a bridge between the wireless and wired networks Wireless Network Basics 1-1
ZyAIR Wireless LAN Utility
Figure 1-1 Ad-hoc Application Example 1 1.3.2 Infrastructure
When wireless clients wish to access and share resources on the wired network, they should use infrastructure mode. Wireless clients may move from one coverage area to another seamlessly without network interruption. This is called roaming. The figure below depicts an infrastructure network example 1-2
Figure 1-2 Infrastructure Application Example
Wireless Network Basics
ZyAIR Wireless LAN Utility
Chapter 2 Disable Windows XP Wireless LAN Configuration Tool
Windows XP includes a configuration tool for wireless devices.
DO NOT use the Windows XP configuration tool and the ZyAIR Utility at the same time. It is recommended you use the ZyAIR Utility to configure the ZyAIR.
Follow the steps below to disable the configuration tool in Windows XP after you install the ZyAIR Utility.
Step 1.
Double-click on the network icon for wireless connection in the system tray. If the icon is not present, proceed to
Step 2
. Otherwise skip to
Step 5
.
Step 2. Figure 2-1 Windows XP: System Tray Icon
If the icon for the wireless network connection is not in the system tray, click
Start
,
Control Panel
and double-click on
Network Connections
. Disable Windows XP Wireless LAN Configuration Tool 2-1
ZyAIR Wireless LAN Utility
Step 3.
Double-click on the icon for wireless network connection to display a status window as shown next.
Step 4. Step 5. Figure 2-2 Windows XP: Wireless Network Connection Status
Click
Properties
and click the
Wireless Networks
tab. Then skip to
Step 6
. When a
Connect to Wireless Network
window displays, click
Advanced…
.
Figure 2-3 Windows XP: Connect to Wireless Network
2-2 Disable Windows XP Wireless LAN Configuration Tool
ZyAIR Wireless LAN Utility
Step 6.
In the
Wireless Network Connection Properties
window, make sure the
Use Windows to configure my wireless network settings
check box is
not
selected. Click
OK
.
Figure 2-4 Windows XP: Wireless Network Connection Properties
Disable Windows XP Wireless LAN Configuration Tool 2-3
ZyAIR Wireless LAN Utility
Chapter 3 Using the ZyAIR Utility
This chapter shows you basic ZyAIR wireless LAN configuration using the ZyAIR Utility.
Install the ZyAIR before you proceed. Refer to the
Quick Installation Guide
. For Windows XP users: disable the Windows XP wireless configuration tool first before you proceed. Refer to
Screen shots for Windows XP are shown unless otherwise specified.
3.1 Accessing the ZyAIR Utility
Follow the steps below to access the ZyAIR Utility After you installed the ZyAIR Utility, an icon for the ZyAIR Utility appears in the system tray.
When the ZyAIR Utility system tray icon displays, the ZyAIR is installed properly. Figure 3-1 ZyAIR Utility: System Tray Icon
The color of the ZyAIR Utility system tray icon indicates the status of the ZyAIR. Refer to the following table for details.
Table 3-1 ZyAIR Utility: System Tray Icon COLOR DESCRIPTION
Red The ZyAIR is working properly but is not connected to any AP or wireless station. Blue The ZyAIR is connected to a wireless network. Double click on the
ZyAIR Wireless LAN Utility
icon in the system tray to open the ZyAIR Utility.
3.2 Viewing Current Configuration
When the ZyAIR Utility starts, the
Link Info
screen displays, showing the current configuration of your ZyAIR. The model name shown in the screens may vary depending on the model you are using. Using the ZyAIR Utility 3-1
ZyAIR Wireless LAN Utility
Figure 3-2 ZyAIR Utility: Link Info
The following table describes the fields in this screen.
Table 3-2 ZyAIR Utility: Link Info LABEL DESCRIPTION
Device Select an available wireless card from the drop-down list menu if you have more than one wireless cards in your computer. Re-Connect Click
Re-Connect
to re-establish connection to the wireless device whose SSID is shown in the
Current Service Set Identifier
field. Current Channel This field displays the radio channel the ZyAIR is currently using. Current Transfer Rate This field displays the current transmission rate of the ZyAIR in megabits per second. 3-2 Using the ZyAIR Utility
ZyAIR Wireless LAN Utility
Table 3-2 ZyAIR Utility: Link Info LABEL DESCRIPTION
Current Service Set Identifier This field displays the name of the wireless device to which the ZyAIR is associated. Tx/Rx Frame Transmitted This field displays the number of data frames transmitted. Received This field displays the number of data frames received. Link Quality Link Strength The status bar and the percentage number show the quality of the signal. The status bar and the percentage number or a number in dBm show the strength of the signal. Percent/dBm Click this button to display either percentages in the
Link Quality
and
Link Strength
fields or a number in dBm in the
Link Strength
field.
3.2.1 Common Screen Command Buttons
The following table describes common command buttons on all ZyAIR Utility screens.
Table 3-3 Common Screen Command Buttons
OK
BUTTON DESCRIPTION
Click
OK
to save all changes and close the ZyAIR Utility. Cancel Click
Cancel
to discard changes and close the ZyAIR Utility. Help Click
Help
to display the on-line help window. The
About
screen displays related version numbers of the ZyAIR. Using the ZyAIR Utility 3-3
ZyAIR Wireless LAN Utility
Figure 3-3 ZyAIR Utility: About
The following table describes the read-only fields in this screen.
Table 3-4 ZyAIR Utility: About FIELD DESCRIPTION
Driver Version This field displays the version number of the ZyAIR wireless card driver. Utility Version Firmware Version This field displays the version number of the ZyAIR Utility. This field displays the version of the firmware on which the driver and the utility are based. This section describes each wireless LAN parameter. 3-4 Using the ZyAIR Utility
ZyAIR Wireless LAN Utility
3.4.1 SSID
The SSID (Service Set Identity) is a unique name shared among all wireless devices in a wireless network. Wireless devices must have the same SSID to communicate with each other.
3.4.2 Channel
A range of radio frequencies used by IEEE 802.11b wireless devices is called a channel.
3.4.3 Transmission Rate (Tx Rate)
ZyAIR provides various transmission (data) rate options for you to select. Options include
Fully Auto
,
1 M bit/sec
,
2 M bit/sec
,
5.5M bit/sec
and
11M bit/sec
. In most networking scenarios, the factory default
Fully Auto
setting proves the most efficient. This setting allows your ZyAIR to operate at the maximum transmission (data) rate. When the communication quality drops below a certain level, the ZyAIR automatically switches to a lower transmission (data) rate. Transmission at lower data speeds is usually more reliable. However, when the communication quality improves again, the ZyAIR gradually increases the transmission (data) rate again until it reaches the highest available transmission rate. If you wish to balance speed versus reliability, you can select any of the above options
11M bit/sec
or
5.5M bit/sec
is used in a networking environment where you are certain that all wireless devices can communicate at the highest transmission (data) rate.
1M bit/sec
or
2M bit/sec
are used often in networking environments where the range of the wireless connection is more important than speed. Wireless LAN works in either of the two modes: ad-hoc and infrastructure. To connect to a wired network within a coverage area using Access Points (APs), set the ZyAIR operation mode to
Infrastructure(BSS)
. An AP acts as a bridge between the wireless stations and the wired network. In case you do not wish to connect to a wired network, but prefer to set up a small independent wireless workgroup without an AP, use the
Ad-hoc (IBSS)
(Independent Basic Service Set) mode.
3.5.1 Ad-Hoc (IBSS)
Ad-hoc mode does not require an AP or a wired network. Two or more wireless clients communicate directly to each other. An ad-hoc network may sometimes be referred to as an Independent Basic Service Set (IBSS). Using the ZyAIR Utility 3-5
ZyAIR Wireless LAN Utility
Figure 3-4 Ad-hoc Network Example To set up an ad-hoc network, configure all wireless clients in ad-hoc network type and use the same SSID and channel. 3.5.2 Infrastructure
When a number of wireless clients are connected using a single AP, you have a Basic Service Set (BSS).
Figure 3-5 BSS Example
A series of overlapping BSS and a network medium, such as an Ethernet forms an Extended Service Set (ESS) or infrastructure network. All communication is done through the AP, which relays data packets to other wireless clients or devices connected to the wired network. Wireless clients can then access resource, such as the printer, on the wired network. 3-6 Using the ZyAIR Utility
ZyAIR Wireless LAN Utility
Figure 3-6 Infrastructure Network Example
3.6 Roaming
In an infrastructure network, wireless clients are able to switch from one AP to another as they move between the coverage areas. During this period, the wireless client maintains uninterrupted connection to the network. This is roaming. As the wireless client moves from place to place, it is responsible for choosing the most appropriate AP depending on the signal strength, network utilization or other factors. The following figure depicts a roaming example. When
Wireless Client B
moves to position
X
, the ZyAIR in
Wireless Client B
automatically switches the channel to the one used by
Access Point 2
in order to stay connected to the network. Using the ZyAIR Utility 3-7
ZyAIR Wireless LAN Utility
Figure 3-7 Roaming Example
3.7 The Site Survey Screen
Use the
Site Survey
screen to scan for and connect to a wireless network automatically. 3-8 Using the ZyAIR Utility
ZyAIR Wireless LAN Utility
Figure 3-8 ZyAIR Utility: Site Survey
The following table describes the fields in the table.
Table 3-5 ZyAIR Utility: Site Survey FIELD DESCRIPTION
SSID This field displays the SSID (or name) of each wireless device. BSSID Channel Signal WEP Search This field displays the MAC address of the wireless device. This field displays the channel number used by each wireless device. This field displays the signal strength of each wireless device. This field shows whether the WEP data encryption is activated (
Enable
) or inactive (
Disable
). Click
Search
to scan for available wireless device within transmission range. Using the ZyAIR Utility 3-9
ZyAIR Wireless LAN Utility
Table 3-5 ZyAIR Utility: Site Survey FIELD DESCRIPTION
Connect Click
Connect
to associate to the selected wireless device. The following table describes the colors used for the entries in the
Site Survey
screen.
Table 3-6 Color Indicator for Link Quality/Link Strength
Green Blue Red Excellent link quality or link strength. Good link quality or link strength. Poor link quality or link strength.
3.7.1 Connecting to a Network
Follow the steps below to connect to a network.
Step 1. Step 2.
Click
Search
to scan for all available wireless networks within range. To join a network, either click an entry in the table to select a wireless network and then click
Connect
or double-click an entry.
Step 3.
If the
WEP
field is
Enable
for the selected wireless network, the following screen displays.
Step 4. Step 5. Figure 3-9 Site Survey Warning
Click
OK
to display the
Security
screen and refer to
click
Cancel
and connect to another wireless network without WEP encryption. To verify that you have successfully connected to the selected network, check the network information in the
Link Info
screen.
3.8 Configuring the ZyAIR Wireless Parameters
Click
Configuration
in the ZyAIR Utility program to display the
Configuration
screen as shown next. 3-10 Using the ZyAIR Utility
ZyAIR Wireless LAN Utility
Figure 3-10 ZyAIR Utility: Configuration
Follow the instructions in the table below to configure the wireless LAN related parameters. Refer to the next section for
Profile
field descriptions.
Table 3-7 ZyAIR Utility: Configuration FIELD DESCRIPTION Configuration
Operating Mode Select
Infrastructure(BSS)
or
Ad-Hoc(IBSS)
from the drop-down list box. Select
Infrastructure(BSS)
to associate to an AP. Select
Ad-Hoc(IBSS)
to associate to a peer ad-hoc computer. Refer to
Using the ZyAIR Utility 3-11
ZyAIR Wireless LAN Utility
Table 3-7 ZyAIR Utility: Configuration FIELD DESCRIPTION
Service Set Identifier (SSID) Enter the SSID of the AP or the peer ad-hoc computer to which you want to associate in this field. To associate to an ad-hoc network, you must enter the same SSID as the peer ad-hoc computer. Enter
Any
to associate to or roam between any infrastructure wireless networks. This is the default setting. Transfer Rate Channel Select a transmission speed from the drop-down list box. Choose from (default),
1M bit/sec
,
2M bit/sec
,
5.5M bit/sec
and
11M bit/sec
.
Fully Auto
Select the channel number from the drop-down list box. To associate to an ad-hoc network, you must use the same channel as the peer ad-hoc computer. Power Saving Mode Select
Enable
from the drop-down list menu to save power (especially for laptop computers). This forces the ZyAIR to go to sleep mode when it is not transmitting data. When you select
Disable
, the ZyAIR will never go to sleep mode. Restore Default Undo Changes Apply Changes Click
Restore Default
to reset all fields back to factory default values. Click
Undo Changes
to start configuring the fields again. Click
Apply Changes
to save the changes back to ZyAIR.
3.9 Network Configuration Profile Setting
The
Profile
in the
Configuration
screen allows you to save the wireless network settings in the
Configuration
screen, use one of the pre-configured network profiles or reset the settings in the
Configuration
screen to the factory default values.
The configuration
Profile
includes the security profiles in the
Security
screen. 3.9.1 Resetting to Factory Default Values
To reset the fields in the
Configuration
screen back to factory default values select
Default
from the drop down list menu and click
Activate
.
3.9.2 Saving the Current Setting to a Profile
To save the current settings in the
Configuration
screen to a new profile enter a descriptive name in the field provided and click
Create
. 3-12 Using the ZyAIR Utility
ZyAIR Wireless LAN Utility
3.9.3 Using a Pre-configured Profile
To use a previously saved network profile select the profile file name from the drop-down list box and click
Activate
.
3.9.4 Deleting a Profile
To delete an existing wireless network configuration select a profile from the drop-down list box and click
Remove
. Using the ZyAIR Utility 3-13
ZyAIR Wireless LAN Utility
Chapter 4 Wireless LAN Security
This chapter shows you how to set up the wireless LAN security available in the ZyAIR.
4.1 Introduction
Wireless LAN security is vital to your network to protect wireless communication between wireless clients and the wired network. Configure the wireless LAN security using the networking device that is in the coverage area.
Security
screen. If you do not enable any wireless security on your ZyAIR, communication between the ZyAIR and the wired network is accessible to any wireless
4.2 Data Encryption with WEP
WEP (Wired Equivalent Privacy) encryption scrambles the data transmitted between the ZyAIR and the AP or other wireless stations to keep network communications private. It encrypts unicast and multicast communications in a network. Both the wireless clients and the access points must use the same WEP key for data encryption and decryption. Your ZyAIR allows you to configure up to four 64-bit or 128-bit WEP keys but only one key can be enabled at any one time.
4.2.1 Configuring the WEP Encryption on the ZyAIR
Click the
Security
tab to display the
Security
screen as shown below. Wireless LAN Security 4-1
ZyAIR Wireless LAN Utility
Figure 4-1 ZyAIR Utility: WEP Encryption
Follow the instructions in the table to configure the WEP encryptions.
Table 4-1 ZyAIR Utility: WEP Encryption FIELD DESCRIPTION
Encryption Select either
64 Bit
or
128 Bit
from the drop-down list box to activate WEP encryption and then fill in the related fields. Select
Disable
to deactivate the WEP data encryption.
WEP Key Entry
The WEP keys are used to encrypt data before it is transmitted. The values for the keys must be set up exactly the same on the APs or other peer ad-hoc wireless computers as they are on the ZyAIR. Key Type Select either the
HEX
or
ASCII
WEP key type. 4-2 Wireless LAN Security
ZyAIR Wireless LAN Utility
Table 4-1 ZyAIR Utility: WEP Encryption FIELD DESCRIPTION
Default Key Select one of the network keys to be the key used for data encryption. Network Key 1 … 4 Enter the WEP keys in the fields provided. If you select
64 Bit
in the
Key Type
field. Enter either ten hexadecimal digits in the range of “A-F”, “a-f” and “0-9” (e.g. 11AA22BB33) for
HEX
key type or Enter five 7-bit printable ASCII characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (e.g. MyKey) for
ASCII
key type. If you select
128 Bit
in the
Key Type
field, Enter either 26 hexadecimal digits in the range of “A-F”, “a-f” and “0-9” (for example, 00112233445566778899AABBCC) for
HEX
key type or Enter 13 7-bit printable ASCII characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (for example, MyKey12345678) for
ASCII
key type.
You
must
configure all four WEP keys the first time you use the ZyAIR.
Restore Default Undo Changes Apply Changes Click
Restore Default
to reset all fields back to factory default values. Click
Undo Changes
to start configuring the fields again. Click
Apply Changes
to save the changes back to ZyAIR. Wireless LAN Security 4-3
ZyAIR Wireless LAN Utility
Chapter 5 Advanced Configuration
This chapter shows you how to configure advanced features of the ZyAIR.
5.1 Overview
The following sections introduce the advanced features you can configure.
5.1.1 Threshold Control Fragmentation Threshold
A
Fragmentation Threshold
is the maximum data fragment size (between 256 and 2432 bytes) that can be sent in the wireless network before the ZyAIR will fragment the packet into smaller data frames. A large
Fragmentation Threshold
is recommended for networks not prone to interference while you should set a smaller threshold for busy networks or networks that are prone to interference. If the
Fragmentation Threshold
value is smaller than the will be fragmented before they reach
RTS/CTS Threshold RTS/CTS Threshold
size. value (see previously) you set then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames
RTS/CTS Threshold
A hidden node occurs when two stations are within range of the same access point, but are not within range of each other. The following figure illustrates a hidden node. Both stations are within range of the access point (AP) or wireless gateway, but out-of-range of each other, so they cannot “hear” each other, that is they do not know if the channel is currently being used. Therefore, they are considered hidden from each other. Advanced Configuration
Figure 5-1 RTS Threshold
5-1
ZyAIR Wireless LAN Utility When station A sends data to the AP, it might not know that the station B is already using the channel. If these two stations send data at the same time, collisions may occur when both sets of data arrive at the AP at the same time, resulting in a loss of messages for both stations.
RTS/CTS Threshold
handshake is invoked. is designed to prevent collisions due to hidden nodes. An
RTS/CTS Threshold
defines the biggest size data frame you can send before an RTS (Request To Send)/CTS (Clear to Send) When a data frame exceeds the
RTS/CTS Threshold
value you set (between 0 to 2432 bytes), the station that wants to transmit this frame must first send an RTS (Request To Send) message to the AP for permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within its range to notify them to defer their transmission. It also reserves and confirms with the requesting station the time frame for the requested transmission. Stations can send frames smaller than the specified
RTS/CTS Threshold
directly to the AP without the RTS (Request To Send)/CTS (Clear to Send) handshake. You should only configure
RTS/CTS Threshold
if the possibility of hidden nodes exists on your network and the “cost” of resending large frames is more than the extra network overhead involved in the RTS (Request To Send)/CTS (Clear to Send) handshake. If the
RTS/CTS Threshold
before they reach value is greater than the
RTS/CTS Threshold
size.
Fragmentation Threshold
value (see next), then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented
Enabling the RTS Threshold causes redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. 5.1.2 Authentication Mode
The IEEE 802.11b standard describes a simple authentication method between the wireless clients and AP. Three authentication modes are defined: Auto, Open and Shared. Open authentication mode is implemented for ease-of-use and when security is not an issue. The wireless station and the AP do
not
share a secret key. Thus the wireless stations can associate with any AP and listen to any data transmitted plaintext. Shared authentication mode involves a shared secret key to authenticate the wireless station to the AP. This requires you to enable a security feature and specify a shared secret key (usually the WEP encryption and WEP key) on both the wireless station and the AP. Auto authentication mode allows the ZyAIR to switch between the open and shared key authentication modes automatically. Use the auto mode if you do not know the authentication mode of the other wireless clients.
5.1.3 Preamble Type
A preamble is a signal used to synchronize the transmission timing in your wireless network. There are two preamble modes: Long and Short. 5-2 Advanced Configuration
ZyAIR Wireless LAN Utility Long preamble mode allows more processing time for each transmitted data packet. Short preamble mode allows less processing time for the transmitted data packets. Using short preamble mode may minimize overhead and maximize network throughput. However, short preamble mode is supported by IEEE 802.11b compliant wireless devices, thus wireless stations using short preamble mode cannot communicate with wireless stations using the original IEEE 802.11 standard. To set the advanced features on the ZyAIR, click the
Advanced
tab.
Figure 5-2 ZyAIR Utility: Advanced
The following table describes the fields in this screen. Advanced Configuration 5-3
ZyAIR Wireless LAN Utility
Table 5-1 ZyAIR Utility: Advanced FIELD DESCRIPTION
Transmit Threshold Control Fragmentation Threshold The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Move the slider to set the fragmentation threshold. RTS/CTS Threshold Data with its frame size larger than this value will perform the RTS/CTS handshake. Setting this attribute to be larger than the maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake. Setting this attribute to zero turns on the RTS/CTS handshake. Move the slider to set the RTS/CTS threshold. Security Shared Mode (Authenticate Access Point) Preamble Type Select this checkbox to use a shared key to authenticate the access point. Refer to
Restore Default Undo Changes Apply Changes Select a preamble type from the drop-down list menu. Choices are
Long Preamble
,
Short Preamble
and
Auto
. The default setting is
Auto
. Refer to
Click
Restore Default
to reset all fields back to factory default values. Click
Undo Changes
to start configuring the fields again. Click
Apply Changes
to save the changes back to ZyAIR. 5-4 Advanced Configuration
ZyAIR Wireless LAN Utility
Chapter 6 Removing and Upgrading the ZyAIR Utility
This chapter describes how to uninstall or upgrade the ZyAIR Utility.
6.1 Removing the ZyAIR Utility
Follow the steps below to remove (or uninstall) the ZyAIR Utility from your computer.
Step 1. Step 2.
Click
Start
,
Programs
,
ZyAIR Wireless LAN Utility
,
Uninstall
. When prompted, click
Yes
to remove the driver and the utility software.
Step 3.
When prompted to restart your computer, click
Yes
and then click
Finish
.
6.2 Upgrading the ZyAIR Utility
Before you uninstall the ZyAIR Utility, save the current network configuration.
To perform the upgrade, follow the steps below.
Step 1. Step 2.
Download the latest version of the utility from the ZyXEL web site and save the file on your computer. Follow the steps in the
section to remove the current ZyAIR Utility
from your computer.
Step 3. Step 4. Step 5.
Restart the computer when prompted. After restarting, refer to the procedure in the
Quick Installation Guide
to install the new utility software. Check the version numbers in the
About
screen to make sure the new utility is installed properly. Removing and Upgrading the ZyAIR Utility 6-1
ZyAIR Wireless LAN Utility
Chapter 7 Troubleshooting
This chapter covers potential problems and the possible remedies. After each problem description, some instructions are provided to help you to diagnose and to solve the problem.
7.1 Problems Starting the ZyAIR Utility Program
Table 7-1 Troubleshooting Starting ZyAIR Utility Program
Cannot start the ZyAIR Wireless LAN Utility The ZyAIR Wireless LAN Utility displays only three tabs. Make sure the ZyAIR is properly inserted and the LED(s) is on. Refer to the
Quick Installation Guide
for the LED descriptions. Use the
Device Manager
to check for possible hardware conflicts. Click
Start
,
Settings
,
Control Panel
,
System
,
Hardware
and
Device Manager
. Verify the status of the ZyAIR under
Network Adapter
. (Steps may vary depending on the version of Windows). Install the ZyAIR in another computer. If the error persists, you may have a hardware problem. In this case, you should contact your local vendor. When the ZyAIR Wireless LAN Utility displays only three tabs, you are using the Windows XP wireless configuration tool at the same time. Refer to the
Disable Windows XP Wireless LAN Configuration Tool
chapter to disable the Windows XP wireless configuration tool. Troubleshooting 7-1
ZyAIR Wireless LAN Utility
7.2 Problems Communicating With Other Computers
Table 7-2 Troubleshooting Communication Problems
The ZyAIR computer cannot communicate with the other computer. A.
Infrastructure
Make sure that the AP and the associated computers are turned on and working properly. Make sure the ZyAIR computer and the associated AP use the same SSID. Change the AP and the associated wireless clients to use another radio channel if interference is high. Make sure that the computer and the AP share the same security option and key. Verify the settings in the
Security
screen. B.
Ad-Hoc (IBSS)
Verify that the peer computer(s) is turned on. Make sure the ZyAIR computer and the peer computer(s) are using the same SS ID and channel. Make sure that the computer and the peer computer(s) share the same security option and key. Change the wireless clients to use another radio channel if interference is high.
7.3 Problem with the Link Status
Table 7-3 Troubleshooting Link Quality
The
Link Quality
is poor all the time. The
Link Strength
all the time. is poor Move your computer closer to the AP or the peer computer(s) within the transmission range. There is too much radio interference (for example microwave or another AP using the same channel) around your wireless network. Relocate or reduce the radio interference. Move your computer closer to the AP or peer computer(s) within the transmission range. There is too much radio interference (for example microwave or another AP using the same channel) around your wireless network. Relocate or reduce the radio interference. 7-2 Troubleshooting
Table 7-3 Troubleshooting Link Quality
ZyAIR Wireless LAN Utility The
Site Survey
screen displays all entries in red. Move your computer closer to the AP or peer computer(s) within the transmission range. There is too much radio interference (for example microwave or another AP using the same channel) around your wireless network. Relocate or reduce the radio interference. Troubleshooting 7-3
ZyAIR Wireless LAN Utility
Index
A
About ..............................................................3-3 Access Point....................................................1-1 Accessing the ZyAIR Utility...........................3-1 Advanced Configuration .................................5-1 AP .............................................
See
Access Point Applications Ad-hoc ........................................................1-1 Infrastructure...............................................1-2 Authentication Mode.......................................5-2 Auto ............................................................5-2 Open............................................................5-2 Shared .........................................................5-2 Auto authentication mode ...............................5-2
B
Basic Service Set....................................
See
BSS BSS .................................................................3-6
C
Common Screen Command Buttons...............3-3 Communication Problem ................................7-2 Ad-hoc(IBSS) .............................................7-2 Infrastructure...............................................7-2 Connecting to a Network ..............................3-10 Copyright ...........................................................ii Disclaimer ......................................................ii Trademarks ....................................................ii CTS (Clear to Send .........................................5-2 Customer Support ............................................vii
D
Data encryption...............................................4-1 Disable Windows XP Wireless Support..........2-1
E
ESS..................................................................3-6 Extended Service Set...............................
See
ESS
F
Federal Communications Commission (FCC) Interference Statement....................................v Fragmentation Threshold ................................5-1
H
Hidden node ....................................................5-1
I
IBSS ................................................................3-5 Independent Basic Service Set ..............
See
IBSS Information for Canadian Users........................iv Caution ..........................................................iv Note...............................................................iv
L
Link Info .........................................................3-1
N
Network Configuration Profile......................3-12 Reset to factory defaults............................3-12 Saving........................................................3-12 Using pre-configured profile.....................3-13 Network Type .................................................3-5 Ad-Hoc(IBSS).............................................3-5 Infrastructure...............................................3-6
O
Online Registration ...........................................iii Index A
ZyAIR Wireless LAN Utility Open authentication mode .............................. 5-2 Operating Mode ......................
See
Network Type
P
Power Saving Mode...................................... 3-12 Preamble Mode............................................... 5-2 Long............................................................ 5-3 Short............................................................ 5-3 Preface ............................................................ xiii problem description ........................................ 7-1 Profile Network Configuration ............................. 3-12
R
Related Documentation................................... xiii Roaming.......................................................... 3-7 Example ...................................................... 3-7 RTS (Request To Send) .................................. 5-2 RTS/CTS handshake....................................... 5-2 RTS/CTS Threshold ....................................... 5-1
S
Service Set Identity...............................
See
SSID Shared authentication mode............................ 5-2 Site Survey...............................................3-8, 3-9 SSID ............................................................... 3-5 Syntax Conventions ........................................ xiii
T
Transfer Rate ................................................ 3-12 Transmission Speed ...................................... 3-12 Transmission Speeds ...................................... 3-5 Troubleshooting.............................................. 7-1 Checking Hardware Conflict ...................... 7-1 Communication problems........................... 7-2 Radio interference................................7-2, 7-3 Starting ZyAIR Utility ................................ 7-1 Survery........................................................ 7-3 B
U
Using the ZyAIR Utility .................................3-1 Note.............................................................3-1
V
Viewing Current Configuration ......................3-1
W
Warranty ...........................................................iii Note...............................................................iii WEP................................................................4-1 WEP Data Encryption Configuring.................................................4-1 Field Descriptions .......................................4-2 WEP Data Encryption with.............................4-1 WEP Key ........................................................4-2 Type ............................................................4-2 Windows XP Requirement .............................2-1 Wired Equivalent Privacy .....................
WLAN ....................................
See See
WEP Wireless LAN .................................................1-1 Applications................................................1-1 Benefits .......................................................1-1 Wireless LAN Parameters...............................3-4 Channel .......................................................3-5 Configuring...............................................3-10 Network Type .............................................3-5 SSID............................................................3-5 Transmission Rate.......................................3-5 Wireless LAN Security ...................................4-1 Data Encryption with WEP.........................4-1 Wireless Network Basics ................................1-1 Wireless LAN
Z
ZyAIR Utility..................................................6-1 About ..........................................................3-4 Before you upgrade.....................................6-1 Link Info .....................................................3-2 Index
Removing....................................................6-1 Site Survey ..................................................3-9 ZyAIR Wireless LAN Utility Upgrading....................................................6-1 WEP Encryption..........................................4-2 Index C
Laadi alla
Avalik link on uuendatud
Teie vestluse avalik link on uuendatud. You may view and manage your chat links after registration here.
Dokumendi avalik link
Reklaam