Gaggenau DF 250 200 series fully integrated dishwasher Operating instructions
Add to My manuals52 Pages
advertisement
*DJJHQDX
en-us fr-ca
Operating instructions Notice d'utilisation
Dishwasher DF250/DF251
2
en-us
Table of contents
en-us Operating instructions
Safety Definitions IMPORTANT SAFETY INSTRUCTIONS
Risk of fire, electrical shock, or serious injury GROUNDING INSTRUCTIONS Safe Operation Proper Care and Maintenance
Causes of Damage Getting Started
Appliance overview Operating panel Dishwasher interior components Display indicators Info button Time setting Switching on the appliance for the first time Settings
Home Connect™ System
Setting up the app Setting up Home Connect WLAN | Network login Connect to App Remote start button Wi-Fi without a connection to the Home Connect server Remote diagnosis
Water softening system / special salt
Water hardness table Adjusting the water softening system Using special salt Detergent with a salt component Switching off water softening system
Rinse Aid
Adding rinse aid Setting the amount of rinse aid used Switching off rinse aid refill indicator
16
16 17 17 18 18
18
18 19 19
11
11 12 12 12 12 12 13 13
15
15 15 15 15 15 16 16 16
6 7
7 8 8 9
10 Loading the Dishwasher
Dishware material Glass and silverware damage Loading the racks Loading patterns Unloading the dishwasher Adjusting the height of the rack RackMatic ® System Removing/Installing third rack Removing/Installing upper rack with Rackmatic ® Rack features
Detergent
Adding detergent Combination detergent
Dishwasher Cycles Dishwasher Cycle Options
Intensive Zone Turbo ¥ Extra Dry Wash Cycle Information
Operating the Dishwasher
Protection against unintentional operation Operating the touch buttons Changing the settings AquaSensor Time display Sensor setting Extra Dry Eco forecast Auto power off Tone volume Button volume Greeting Factory setting Switching the appliance on Delay start time InfoLight ® * EmotionLight Wash cycle end Switching off the appliance Interrupting the wash cycle Cancel a cycle (reset) Changing the wash cycle
32
35 35 35 35 35 35 32 32 32 33 33 33 33 33 33 33 33 34 34 34 34 34
31
31 31 31 31
20
20 20 21 21 23 23 23 24 25 26
28
28 29
30 3
en-us
Care and Maintenance
Cleaning the dishwasher Special salt and rinse aid Filters Spray arms Drain pump Preparing your unit for vacation Winterizing your unit
Troubleshooting
Error message Fault table
Customer Service Statement of Limited Product Warranty
What this Warranty Covers & Who it Applies to: How Long the Warranty Lasts Repair/Replace as Your Exclusive Remedy Out of Warranty Product Warranty Exclusions How to Obtain Warranty Service
Installation and connection
Parts included Safety instructions Delivery Technical specifications Installation Drain connection Water supply connection Hot water connection Electrical connection Removing the appliance Transporting the appliance Securing the appliance against frost
47
47 47 48 48 48 49
49
49 49 50 50 50 50 51 51 52 52 52 52
36
36 36 36 38 38 39 39
40
40 40
47 4
en-us &RQJUDWXODWLRQVDQG7KDQN 5 Safety Definitions en-us Safety Definitions WARNING This indicates that death or serious injuries may occur as a result of non-observance of this warning. CAUTION! This indicates that minor or moderate injuries may occur as a result of non-observance of this warning. NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory. Note: This alerts you to important information and/or tips. 6 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS This dishwasher is provided with Installation Instructions and this Use and Care Manual. Read and understand all instructions before using the dishwasher. This dishwasher is intended for use up to a maximum altitude of 13,000 ft (4,000 meters) above sea level. To reduce the risk of fire, electrical shock, or serious injury, observe the following: Risk of fire, electrical shock, or serious injury WARNING Risk of injury or death! Misuse of the dishwasher can result in serious injury or death. Do not use the dishwasher in any way not covered in this manual or for any purpose other than those explained in the following pages. WARNING Risk of electrical shock or fire! Electrical shock or fire could result if the electrical supply for the dishwasher covered in this manual is incorrectly installed or if the dishwasher has been improperly grounded. Do not use the dishwasher covered in this manual unless you are certain the electrical supply has been correctly installed and the dishwasher has been properly grounded. WARNING Health hazard! Never use harsh chemicals to clean your dishwasher. Some bleach-based products can damage your dishwasher and may present health hazards! WARNING Risk of injury! Severe injury and/or product damage could result from the use of unauthorized service technicians or non-original replacement parts. All repairs must be performed by an authorized service technician using only original equipment factory replacement parts. 7 8 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This appliance must be grounded to a metal, permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dishwasher. See the Installation Instructions included with this dishwasher for more information on electrical requirements. WARNING Risk of electric shock! This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor. Improper connection of the equipment grounding conductor can result in risk of electric shock. Check with a qualified electrician if you are in doubt whether the appliance is properly grounded. Safe Operation Use this dishwasher only for its intended function, which is the washing of household dishware and kitchenware rated as dishwasher safe. Use only detergents or rinsing agents recommended for use in a dishwasher, and keep them out of the reach of children. CAUTION! When loading items to be washed: ʋ ʋ ʋ ʋ ʋ Locate sharp items so they are not likely to damage the door seal. Load knives and other sharp utensils with their HANDLES UP to reduce the risk of cut-type injuries. Do not wash plastic items unless they are marked “dishwasher safe” or the equivalent. For plastic items not so marked, check the manufacturer’s recommendations. Do not operate your dishwasher unless all enclosure panels are in place. Do not tamper with or override controls and interlocks. Do not abuse, sit or stand on the door or dish racks of the dishwasher. IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS WARNING Risk of injury! To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot water or steam may escape. Do not fully open the door until water noises have stopped and steam has subsided. To reduce risk of injury, do not allow children to play in or on the dishwasher. When children become old enough to operate the appliance, it is the responsibility of the parents/legal guardians to ensure the children are instructed in safe practices by qualified persons. Remove the dishwasher door to the washing compartment when removing an old dishwasher for service or discarding. To avoid floor damage and possible mold growth, do not allow wet areas to remain around or under the dishwasher. Note: To avoid dishwasher damage, do not allow water to remain in your dishwasher systems through extended periods of freezing temperatures. Freezing temperatures can damage the water fill valve and potentially other components of your dishwasher. information. It is highly recommended for the end user to become familiar with the procedure to shut off the incoming water supply and the procedure to shut off the incoming power supply. See the Installation Instructions or contact your installer for more NSF/ANSI 184 Certified residential dishwashers are not intended for licensed food establishments. Proper Care and Maintenance WARNING Risk of explosion! Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. Hydrogen gas is explosive. Before using a dishwasher that is connected to a hot water system that has been unused for two weeks or longer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is explosive, do not smoke or use an open flame during this time. State of California Proposition 65 Warning: WARNING This product can expose you to chemicals including vinyl chloride, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov . 9 en-us Causes of Damage Causes of Damage NOTICE: ʑ Never use steam cleaning products to clean your dishwasher. The manufacturer will not be liable for the possible damages or consequences. ʑ To avoid possible dishwasher damage, do not use harsh chemicals, abrasive cleaners, scouring pads (metal or plastic), or abrasive cloths/paper towels to clean your dishwashers exterior door panel. Your dishwasher's exterior door panel can be damaged by doing so. ʑ To avoid dishwasher damage, do not load the dishwasher with paper products, plastic bags, packing materials or anything other than normal, dishwasher safe dishware and kitchenware. ʑ Protect your dishwasher from the elements. Protect against freezing to avoid possible damage to the fill valve. Damage caused by freezing is not covered by the warranty. 10 Getting Started en-us Getting Started VHF W K PLQ 67$57 UHVHWVHF The dotted lines show optional features which may or may not be included with your dishwasher. 11 en-us Getting Started The numbers stated below refer to the overview images on the previous page of this manual. ( 0 8 On/Off button Wash cycles** Info button @ H P X ` Digital display Rinse aid refill indicator Salt refill indicator Selection buttons Delay start / < button h )" Remote start / > buttton Wash cycle options** )* START button ** the wash cycles and options will vary by model ------- ¯ : ¯¯ % $ | Cycle time remaining Lights up when rinse aid is low Lights up when salt is low Lights up when wifi is connected Info button The Info button cycle information. can be used to display additional wash 1. Press the Info button 8 . 2. Press the wash cycle button. Information on the selected wash cycle is indicated on the display window at the top @ . 3. To leave, press Info button 8 . 1" Interior light * 1* Third rack 12 Upper rack 1: Upper spray arm 1B Detergent tab tray 1J Lower spray arm 1R Dispenser for special salt 1Z Filters 1b Silverware basket * 1j Lower rack 9" Rinse aid dispenser 9* Detergent dispenser 92 Lock for detergent dispenser 9: Rating plate * optional feature which may or may not be included with your dishwasher. Time setting When the appliance is switched on for the first time, the time starts at 12:00 o’clock. Set the time as follows: 1. Open the door. 2. Switch on ON/OFF switch ( . 3. Press Info button following text is indicated on the display window at the top @ : 8 for 3 seconds until the Scroll with < > Set with - + Leave with W 3 sec. 4. Keep pressing button > ` until the time setting is indicated on the display window at the top @ . 5. Make the setting with setting buttons + - X . If the selection buttons + - X are held down, the set values are changed in 10-minute increments. 6. Press and hold the Info button 8 for 3 seconds. The selected setting has now been stored. Note: If the appliance was disconnected from the power supply for a prolonged period, the time starts at 12:00 o’clock. Set the time. 12 ------- Getting Started en-us When you first turn on the dishwasher, you are taken directly to the settings for switching on the appliance for the first time. The following text is indicated on the display window at the top @ : Scroll with < > Set with + Leave with W 3 sec. Settings Switching on the appliance for the first time Language Time format Time setting Water soft setting Rinse aid setting Factory setting American English 24h 12:00 °E 0 - 8 soft Level 5 The required settings for switching on the appliance for the first time are listed in the table below. Change the setting as follows: 1. Keep pressing button > ` until the required setting is displayed. 2. Make the selection with setting buttons + - X . 3. Press and hold the Info button 8 for 3 seconds. The selected setting has now been stored. Infotext by pressing Info button Language selection. 12h or 24h. Set the current time. Setting water hardness. When using Multitabs, select the lowest setting. Amount of rinse aid affects drying. The dishwasher has been preset with certain settings for your convenience. You can change these factory setting. Change the setting as follows: 1. Open the door. 2. Switch on ON/OFF switch ( . 3. Press Info button following text is indicated on the display window at the top @ : 8 for 3 seconds until the Scroll with < > Set with - + Leave with W 3 sec. Setting Factory setting Time setting Time format Time display Language Water hardness Rinse aid disp. Sensor setting Extra dry Eco forecast 12:00 24h Time American English °E0-8 Soft Level 5 Standard Off Off 4. Keep pressing button > ` until the required setting is displayed. 5. Make the selection with setting buttons + - X . 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. You have the option of resetting all changed settings back to the original factory settings. Note: When you reset your dishwasher to the factory settings, you are taken directly to the settings for switching on the appliance for the first time. Infotext by pressing Info button Set the current time. 12h or 24h. Show end of wash cycle with display "Time" or "In hours". Language selection. Setting water hardness. When using Multitabs, select the lowest setting. Amount of rinse aid affects drying. Adjusting water clarity detection for best cleaning results. Improved drying for glasses and plasticware. Show the water and energy consumption. 13 en-us Getting Started Setting Auto Power Off EmotionLight Front display* Remaining time proj. * Infolight * Start Program Tone volume Button volume WLAN Network login Factory setting Off On On On On Auto 130-150 °F Level 2 Level 2 on/off Manual or Autom./ WPS Connect to App Greeting Start with + On Factory setting Reset * depending on the features of your dishwasher Notes ʑ ʑ The “Network login” menu option is only available if WLAN has been switched on. The “Connect to App” menu option is only available if a connection to the home network has been established. -------- Infotext by pressing Info button Appliance automatically switches off at end of rinsing process. Interior light. The front display can be selected. While program is running, status information is projected onto floor. Light is projected to signal an active cleaning cycle. When switching on, the last selected wash cycle appears. Volume of signal at end of wash cycle. Volume when using buttons. Switch wireless network connection on or off. Check WPS function on router. WLAN must be turned on for this setting to appear. No WPS function: Manual WPS function: Automatic Connect appliance to mobile terminal device. Appliance must be connected to the network for this setting to appear. When switching on the appliance, the brand logo can be deselected. Resetting to the factory setting. 14 This dishwasher is Wi-Fi capable and can be remotely controlled via a mobile device. If your dishwasher does not connect to the home network, you can also operate the dishwasher manually by pressing the buttons. Refer to appliance overview for the location of the buttons. a "Appliance overview" on page 11 Getting Started en-us | In the WLAN menu you can activate the wireless network connection with “on” and deactivate it with “off”. Notes ʑ ʑ If you have selected the Wi-Fi “off” setting, the “Network login” and “Connect to App” settings are not available. Remote control of the appliance requires a stable wireless network connection. To be able to operate the appliance via Home Connect, the Home Connect app must be installed on your mobile device. Observe the supplied Home Connect documents with regard to this. Follow the steps specified by the app to implement the settings. You can set your dishwasher by pressing the remote start button h or proceed as follows: 1. Open the door. 2. Switch on the On/Off switch ( . 3. Press Info button the top @ : 8 for 3 seconds until the following text is indicated on the display window at Scroll with < > Set with - + Leave with Setup 3 sec. 4. Keep pressing button > h until the required setting is indicated on the display window at the top @ . 5. Make the setting with setting buttons + - X . See table in section 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. In the “Network login” menu you can select between “Automatic/WPS” and “Manual” to connect the dishwasher to your home network. To do this, test the WPS function on your router. Refer to Home Connect leaflet for detailed instructions. Automatic: Connect to the home network using the WPS function of your router. Manual: Connect your mobile device to the Home Connect network. The network settings are then manually entered using the Home Connect App to connect to your home network. Following successful connection, the following text is indicated on the display window at the top @ : “Network login successful”. Note: The “Network login” menu item is not available unless you have activated WLAN. The “Connect to App” menu option is not available unless there was a connection to the home network. The “Connect to App” setting establishes the link between the dishwasher, App and your user account. Following successful connection, the following text is indicated on the display window at the top @ : “Connection to app successful”. Refer to the Home Connect leaflet for further information. 15 en-us Water softening system / special salt Once the dishwasher is connected to the home network, press the remote start button h to control the dishwasher from your device. If the dishwasher has still not logged into Home Connect, access the Home Connect settings by pressing the remote start button h . Follow the directions in the supplied Home Connect leaflet. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Remote Start button h , the operation will be paused. Press the Remote Start button h again and close the appliance door to resume control. Also see section Notes ʑ ʑ ʑ ʑ When the login process is complete, the Remote Start button h goes out. To activate the remote control, press the Remote Start button h . If the Home Connect Assistant was aborted during start-up, press the Remote Start button h again. If the connection to the router fails, | flashes on the display. ƒ Wi-Fi without a connection to the Home Connect server You can use the Home Connect App to disconnect from the Home Connect server. The appliance is then locally connected to your mobile device without any connection to the Home Connect server. Note: If you did not deactivate the connection to the Home Connect server, check your Internet connection. ~ Remote diagnosis Customer Service can use Remote Customer Service ~ to access your appliance if you contact them. Notes ʑ ʑ You have to confirm Customer Service access on your appliance. You can switch off Remote Customer Service ~ using the On/Off switch ( or deactivate Customer Service access in the Home Connect App. Water softening system / special salt To ensure good rinsing results, the dishwasher requires soft water, i.e. water which is low in lime, otherwise limescale will be deposited on the utensils and interior container. Tap water above 7° dH (1.2 mmol/l) must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see following water hardness table). :DWHU KDUGQHVV YDOXH( +DUGQHVV UDQJH PPROO Ȣ Ȣ Ȣ Ȣ Ȣ Ȣ Ȣ Ȣ VRIW VRIW PHGLXP PHGLXP PHGLXP KDUG KDUG KDUG Ȣ Ȣ Ȣ Ȣ Ȣ Ȣ Ȣ Ȣ 6HWYDOXH RQWKH PDFKLQH 16 The amount of salt dispensed can be set from 0 to 62 °E. Salt is not required at the set value 0-8 . Set the softening system as follows: 1. Ask your local water utility company for the water hardness value of the tap water. 2. Required setting can be found in the water hardness table. 3. Open the door. 4. Switch on ON/OFF switch ( . 5. Press Info button following text is indicated on the display window at the top @ : 8 for 3 seconds until the Scroll with < > Set with - + Leave with W 3 sec. 6. Keep pressing button > ` until the water hardness is indicated on the display window at the top @ . 7. Make the selection with setting buttons + - X . 8. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. Water softening system / special salt en-us As soon as the low salt indicator salt dispenser should be done P before lights up on the digital display, salt should be topped off. Refilling the switching on the appliance. This ensures that extra salt water is washed out and will not corrode the rinsing tank. NOTICE: Detergent will destroy the water softening system! Never pour detergent into the salt dispenser. Top off the salt as follows: 1. Undo the screw plug on the dispenser 1R . 2. Fill the dispenser with water (required only when switching on the appliance for the first time). 3. Add salt as illustrated (do not use table salt or tablets) . The water is displaced and runs out. For more information about buying dishwasher salt, please contact Customer Service 1-800-944-2904. 17 en-us Rinse Aid Detergent with a salt component If combined detergents with a salt component are used, special salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, salt must be used. Switching off water softening system If the use of combined detergents with a salt component impairs the low salt indicator control panel or the text on the display window at the top @ (enough salt for x rinse cycles), the displays can be switched off. P on the Proceed as described under “Setting water softening system” and set the value to 0-8 . The water softening system and salt refill indicator are now switched off. Rinse Aid As soon as the low rinse aid indicator H lights up on the control panel, rinse aid should be topped off. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid which the manufacturer designates as safe to use in domestic dishwashers. Combined detergents with rinse aid component may be used with soft to moderately hard water only (0-2 bands on test strip or up to an °E value of 20). For moderately hard to hard water (3 to 4 bands on test strip or °E value of 21 or higher), rinse aid must be used. NOTICE: To avoid oversudsing or clogging, do not overfill the rinse aid dispenser 9" . Wipe up any spills with a damp cloth. 1. Open the rinse aid dispenser 9" by pressing on the latch of the lid and pulling it open. 2. Add liquid rinse aid to the dispenser 9" until it is full. Do not overfill. Avoid spilling into air vent hole. BJS WFOU PD[ 18 3. Close the lid. Lid must be fully closed until it clicks in order to seal. 4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full. This prevents excessive frothing during the next wash cycle. The indicator light will go out a few moments after the dishwasher door is shut. Tip: For easier pouring, remove lid from the rinse aid bottle. NOTICE: Do not fill the rinse aid dispenser 9" with detergent. Doing so will damage the dishwasher. Rinse Aid en-us If the use of combined detergents with a rinse aid component impairs the low rinse aid indicator the displays can be switched off. H on the control panel (enough rinse aid for x rinse cycles), Proceed as described under “Setting amount of rinse aid” and select setting 0 . NOTICE: Using no rinse aid or setting the dispenser to 0 may result in longer cycle times consuming more energy and water. The higher temperatures can damage fine china or glassware. The amount of rinse aid to be dispensed can be set from 0 to 6 . Set the amount of rinse aid to be dispensed to 5 to obtain a very good drying result. Do not change the amount of rinse aid unless there are streaks or water stains on the utensils. Set a lower level to avoid streaks. Set a higher level to avoid water stains. Set the amount of rinse aid as follows: 1. Open the door. 2. Press on ON/OFF button ( . 3. Press Info button following text is indicated on the display window at the top @ : 8 for 3 seconds until the Scroll with < > Set with - + Leave with W 3 sec. 4. Keep pressing button top @ . > ` until the rinse aid dispenser is indicated on the display window at the 5. Make the selection with setting buttons + - X . 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. Note: Do not change the amount of rinse aid unless there are streaks (select lower setting) or water stains (select higher setting) visible on the utensils. 19 en-us Rinse Aid Note: Before using your dishwasher for the first time, check the information in this section. Some items are not dishwasher-safe and should be hand washed; others require special loading. Recommended Aluminum China, Crystal, Stoneware Glass Precaution Colored anodized aluminum may fade over time. Minerals in your water may cause the aluminum to darken or spot. This can usually be removed with a soap-filled steel wool pad. Some hand-painted utensils may discolor, fade or spot. Hand wash these utensils. Position fragile glassware so that it will not topple over or come in contact with other utensils during the wash cycle. Make sure to use dishwasher- safe glass. Milk glass may discolor or become yellow. Non-stick Coatings Apply a light coating of vegetable oil to non-stick surfaces after drying. Plastics Make sure the plasticware is dishwasher-safe. Stainless Steel, Sterling Silver and Silver Plates Load these so they do not come in contact with other metals, stainless steel dishwasher tank walls or the inner door. Not Recommended Acrylic Adhesive- Joined Pieces Bone-Handled Utensils Iron Non-Dishware Items Pewter, Brass, Bronze Reason Crazing or small cracks throughout the acrylic, may occur. Adhesives that join materials such as plastic, wood, bone, steel, copper, tin, etc. may loosen. Handles may separate. Iron will rust. Hand wash and dry immediately. Your dishwasher is intended for use in cleaning ONLY standard household dishware and kitchenware. These items will tarnish. Hand wash and dry immediately. Causes: ʑ Glass type. ʑ Type of dishwasher detergent. ʑ Water temperature of the wash cycle. Recommendation: ʑ Use only glasses and porcelain which the manufacturer designates as dishwasher-safe. ʑ Use a detergent which protects silverware. ʑ Use less intensive wash cycles and take glass and silverware out of the dishwasher as soon as possible after the wash cycle ends. 20 Rinse Aid en-us For best dishwashing results, observe the following when loading the dishwasher: ʑ Do not pre-wash items with loosely attached food soil. ʑ Remove all food particles, bones, toothpicks and excessive grease. ʑ Pre-treat items having burned-on, baked-on or starchy soils. ʑ Load dishes in the dishwasher racks so the insides of bowls, pots and pans are facing the spray arms. ʑ Avoid nesting and contact points between dishes. ʑ Separate items of dissimilar metals. Use care to not block movement of the spray arms. ʑ Only wash household dishware and kitchenware rated as dishwasher-safe. Refer to the Dishware Materials section for more information about dishware suitability. NOTICE: To avoid dishwasher damage, do not load the dishwasher with paper products, plastic bags, packing materials or anything other than normal, dishwasher safe dishware and kitchenware. Loading the upper rack Ensure items do not protrude through the bottom of the racks and block the spray arms. Note: When pushing the upper rack tub so the upper rack spray arm using the door. 1: 12 into the dishwasher, push it until it stops against the back of the connects to the water supply at the back of the tub. Do not push racks in Loading the lower rack Place large items in the lower rack 1j . Load pots, pans and bowls upside down. For daily, regular or typical use Loading patterns for lower rack Lower rack 1j Alternate loading pattern with pots and pans For best results, load large items face down in the lower rack. 21 en-us Rinse Aid Loading patterns for upper rack 12 place setting suggested loading pattern, with cutlery drawer Alternate loading pattern with stemware Alternate loading pattern Use supports to load stemware glasses in the upper rack. Loading patterns for third rack 12 place setting suggested loading pattern * 22 CAUTION! Dishes can be very hot immediately after cycle ends. Open the door slightly and allow dishes to cool for a few minutes before unloading. Rinse Aid en-us ® The height of the upper rack lower rack. 12 can be adjusted in 3 steps to create more space for larger items in the 1. Pull the upper rack out of the dishwasher until it stops. 2. To lower the rack, push the RackMatic® lever inward. 3. To raise the rack, hold the basket on the sides of the upper rack and lift it up. Note: Dishes are more likely to chip when unloading before cooling. When unloading the dishwasher, to prevent water from dripping onto dry dishes, unload the lower rack 1j first. Next, unload the silverware basket 1b followed by the upper rack 12 , and then the third rack (if equipped). Adjusting the height of the rack The height of the upper rack or lower rack. 12 can be adjusted to create more space for taller utensils either in the upper Setting 1 max. ø Setting 2 max. ø Setting 3 max. ø Upper rack 7 in (18 cm) 8 in (20.5 cm) 9 in (23 cm) Lower rack 12.25 in (31 cm) 11.5 in (29 cm) 10.5 in (26.5 cm) Arrange large plates up to a diameter of 12.25 in (31 cm) in the lower basket 1j as illustrated. Note: Check spray arm for clearance after adjustment. 23 en-us Rinse Aid Installing third rack 1* 1. Pull out third rack rails all the way (1). 2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2). 3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3). 4. Push in third rack (4). Removing third rack 1* 1. Pull out third rack all the way (1). 2. Lift upper rollers over the stopper hooks of both rails (2). 3. Pull third rack out forward and upward so that the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3). 24 ® Rinse Aid en-us Installing upper rack 12 1. Pull out upper rack rails all the way (1). 2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2). 3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3). 4. Push in upper rack (4). Removing upper rack 12 1. Pull out upper rack all the way (1). 2. Lift front rollers over the stopper hook of the rail (2). 3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3). 25 en-us Rinse Aid Flip tines Depending on the features of your dishwasher, the tines can be folded down. This facilitates arrangement of pots, bowls and glasses. Fold down the flip tines as follows: 1. Pull flip tine gently forward and release it from the notch (1). 2. Push the flip tine downward to the desired position (2). Third rack The third rack horizontally positions knives, spatulas and other oversized tools for improved cleaning and easier loading and unloading. Arrange cutlery in third rack as illustrated. To fold up, push flip tines into an upright position until the holder engages in the notch. Cup shelves The cup shelves and the space underneath them can be used for small cups or for larger serving utensils. &/,&. 26 Stemware support The lower rack accommodates two rows of stemware by placing glasses on angled flip tines and resting the stems against the wine stem bar and cup shelves. Rinse Aid en-us Extra tall item sprinkler If an item is too tall to be placed in the lower rack 1j even with the upper rack 12 in the raised position, remove the empty upper rack guides (A) . 12 by pulling it out of the dishwasher until it stops. Pull the front of the rack upward and outward until the rack will not slide out anymore. Then lift it up and away from the dishwasher, until the rollers are completely free of the roller Set the upper rack 12 aside and push the roller guides (A) back into the dishwasher. Insert the extra tall item sprinkler (B) into the upper rack spray outlet (C) and turn the sprinkler clockwise to lock into position. $ & $ % NOTICE: To avoid dishwasher damage, do not reinstall the upper rack 12 without removing the extra tall item sprinkler (B) . 27 en-us Detergent Use only detergent specifically designed for dishwashers. For best results, use fresh powdered dishwashing detergent or detergent tabs. NOTICE: To avoid damage to dishwasher or dishware: ʑ Do not use hand dishwashing products in your dishwasher. ʑ Do not use too much detergent if your water is soft. Using too much detergent with soft water may cause etching in glassware and fine china. ʑ To best protect glassware, use a wash cycle with low temperatures or a specific glass-care cycle (depending on the model) and use a detergent that includes etch protection. Note: If you do not know the hardness of your water supply, use 15 ml of detergent. Increase the amount if necessary to the least amount required to get your kitchenware clean. 3. Dosage: see manufacturer’s instructions on the packaging. Use graduated detergent dispenser. Usually 1¼ to 1½ tablespoons (20 ml–25 ml) are adequate for normal soiling. If using tablets, one tablet is adequate. êWEVS PO êWEVS PO WEVS PO 4. Close cover on the detergent dispenser. Cover “clicks” into position. &/,&. 1. If the detergent dispenser 9* is still closed, actuate locking bar 92 to open it. 2. Pour detergent into the dry detergent dispenser 9* only. Do not overfill the detergent dispenser. When using detergent tabs, lay them such that they do not come in contact with the cover, insert a detergent tab flat, not on its side. Note: Do not place detergent tabs in the tab tray 1B . Place tabs or other detergent forms directly in the detergent dispenser 9* . The detergent dispenser opens automatically at the optimum time depending on the wash cycle. The powder or liquid detergent is distributed in the appliance and is dissolved, the detergent tab falls into the detergent tab tray where it dissolves in doses. Tip: If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate. Suitable detergents and care products can be purchased online via our website or via customer service (see back page). 28 Apart from conventional single function detergents, a number of products are offered with additional functions. These products contain not only the detergent but also rinse aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5in1, ...), additional components such as glass protection or stainless steel cleaner. Combination detergents function only up to a specific degree of hardness (usually 21°dH). Over this limit salt and rinse aid must be added. As soon as combined detergents are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result. Notes ʑ ʑ ʑ If you want to add more utensils after the wash cycle has started, do dissolved tab. not use the detergent tab tray 1B already be there and you will touch the partially as a handle for the upper rack. The detergent tab could Do not place small parts for washing in the detergent tab tray 1B ; this prevents the detergent tab from dissolving evenly. You will obtain optimum rinsing and drying results by using single function detergents and applying salt and rinse aid separately. Detergent en-us ʑ ʑ ʑ ʑ ʑ ʑ If wash cycles are short, detergent tabs may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue. It is recommended to use washing powder for these wash cycles. The dosing of a detergent tab is adequate for the “Intensive” wash cycle (for some models). When using washing powder, you can apply some of this cleaning agent to the inside of the appliance’s door. Even if the rinse-aid and/or salt refill indicator is lit, the rinse cycle will run correctly with combined detergents. If using detergents in a water-soluble protective cover: Take hold of the cover with dry hands only and put the detergent into an absolutely dry detergent dispenser only, otherwise the detergent may stick. If you switch from combined detergents to single function detergents, ensure that the water softening system and amount of rinse aid have been set to the correct value. Biological/eco detergents: Detergent products identified as “Bio” or “Eco” (to protect the environment) usually use lower quantities of active agents or completely dispense with certain substances. The cleaning effect of such products may occasionally be restricted. 29 en-us Dishwasher Cycles Dishwasher Cycles Note: In order to save energy, it is recommended to set the Auto Power Off feature to “After one minute”. Wash cycle AUTO 150 - 160° F AUTO Wash 130 - 150° F Regular (see note at bottom of table) Quick Wash Glass Care Rinse Recommended use This cycle cleans items having baked-on or hard dried-on food soils. These items may require soaking or hand scouring. This cycle is appropriate for mixed loads. It is optimised according to the soiling with the aid of sensors. Recommended for daily, regular or typical use to completely wash a full load of normally soiled dishes. Possible wash cycle option all all Cleans lightly soiled dishes with easy to remove food soils. A cycle for lightly soiled dishes which is ideal for temperature sensitive dishes or silverware. In this cycle the temperature is reduced to help prevent dishes from becoming damaged. It is especially helpful to reduce a cloudy or etched appearance on glasses. Note: Some glasses are more prone to etching due to the glass manufacturing process. Use this cycle if you need to pre-rinse dishes to avoid odors. Place unrinsed dishes inside the dishwasher and select the Rinse cycle. Uses less water than hand rinsing and very low energy. all Note: In order to obtain optimal performance with minimum energy consumption, it is recommended to disable all available options and settings, except Auto Power Off Extra Dry all Note: The Energy Guide label was based on the Normal or Regular soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 9" . A single dose of detergent was inserted into the detergent dispenser 9* , with no detergent being used in the prewash. The unit was not subjected to truncated testing per the definitions in the test procedure. We recommend that dish loads such as the one in the energy certification test have the rack position set in the highest position. 30 Dishwasher Cycle Options en-us Dishwasher Cycle Options Ï Intensive Zone Perfect for a mixed load. You can wash very soiled pots and pans in the lower rack together with normally soiled utensils in the upper rack. The spray pressure in the lower rack is intensified, the rinsing temperature is increased slightly. ½ Extra Dry An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. ¥ Turbo is an option that allows saving time without sacrificing wash and dry performance. Selecting this option ensures the same final temperatures as the underlying cycle by starting the heat period at an earlier phase in the program. Selecting this option also increases energy consumption while reducing cycle time. AUTO Wash 130-150°F AUTO* 150-160°F Cycle time in min. Water cons. in L (gal) Wash temp. in °F (°C) 105 - 130 9.4-20.2 (2.5-5.3) 127-131 (53-55) 110 - 135 18.6-24.2 (4.9-6.4) 151-160 (66-71) Rinse temp. in °F (°C) 153-162 (67-72) 162 (72) Intensive Zone Cycle time in min. Water cons. in L (gal) Rinse temp. in °F (°C) 120-145 9.4-20.2 (2.5-5.3) 153-162 (67-72) 125-145 18.6-24.2 (4.9-6.4) 162 (72) Turbo Cycle time in min. Water cons. in L (gal) Rinse temp. in °F (°C) 75-90 16.1-20 (4.3-5.3) 153-162 (67-72) 95-110 16.3-20.5 (4.3-5.4) 162 (72) Extra Dry Cycle time in min. Water cons. in L (gal) Rinse temp. in °F (°C) *sanitize 125-150 9.4-20.2 (2.5-5.3) 162 (72) 130-150 18.6-24.2 (4.9-6.4) 162 (72) To save energy, this dishwasher has EcoSense where the sensors in the dishwasher automatically adjust the cycle length, temperature and water changes based on the amount of food soil and the incoming water temperature. The “Smart Control” makes decisions that can cause the cycle time and water usage to adjust intermittently. Wash cycle times are based on 120°F (49° C) water supply. different than 120°F (49° C), your dishwasher’s cycle times may be impacted. Normal 130 - 135 8.5-20.6 (2.2-5.4) 113-131 (45-55) 140-156 (60-69) 145-150 8.5-20.6 (2.2-5.4) 156 (69) 95-105 16.6-21.1 (4.4-5.6) 162 (72) 140-155 8.5-20.6 (2.2-5.4) 162 (72) Quick Wash 30 10.5 (2.8) 113 (45) 127 (53) N/A N/A N/A N/A N/A N/A 50 10.5 (2.8) 162 (72) If your household water supply is Glass Care 70 13 (3.4) 122 (50) 140 (60) 85 13 (3.4) 140 (60) 60 13.3 (3.5) 140 (60) 100 13 (3.4) 162 (72) Rinse 9 4.1 (1.1) incoming incoming N/A N/A N/A N/A N/A N/A N/A N/A N/A Note: Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cycles have passed sanitization performance tests. 31 en-us Operating the Dishwasher Operating the Dishwasher Note: With hidden controls, the door must be opened before changing settings and closed after changing settings. WARNING Risk of injury! To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot water or steam may escape. Do not fully open the door until water noises have stopped and steam has subsided. Your dishwasher is equipped with a function that helps to prevent unintentional operation (e.g. by children). After starting the dishwasher, the dishwasher door has to be closed within 4 seconds, otherwise the operation will be paused. There will be a signal on the control panel advising you to press the Start button again and close the door. This function will be activated when: ʑ pressing Start to begin a wash cycle ʑ setting Delay time and pressing Start ʑ opening the door while Delay time is active ʑ opening the door during a wash cycle. Note: This function cannot be deactivated. Buttons are sensitive and should be touched gently. Avoid any grease or food particles resting on the buttons as they could activate the dishwasher. Wiping and cleaning can also activate the dishwasher. For best results, use bare, clean hands when touching the buttons. To clean the touch buttons wipe them with a dry or slightly damp cloth. The dishwasher has been preset with certain settings for your convenience. You can change these factory settings. Change the setting as follows: 1. Open the door. 2. Switch on On/Off button ( . 3. Press Info button 8 for 3 seconds until the following text is indicated in the digital display @ : Scroll with < > Set with - + Leave with Setup 3 sec. 4. Keep pressing button > ` until the required setting is indicated in the display window at the top @ . 5. Make the selection with setting buttons + - X . 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. Tip: If you change several settings, first make all changes in succession. Now press the Info button 8 for 3 seconds. This saves all set values in the appliance. 32 The AquaSensor is an optical measuring device which measures the cleanliness of the rinse water. The AquaSensor is used according to the wash cycle. If the AquaSensor is active, “clean” rinse water can be transferred to the next rinse and water consumption can be reduced by 0.8–1-5 gal (3–6 liters). If the rinse water is not yet clear, the water is drained and is replaced with fresh water. In the automatic wash cycles the temperature and running time can also be adjusted to the degree of soiling. Operating the Dishwasher en-us The final rinse uses a higher temperature which improves the drying result. The cycle time may increase slightly. (Caution if utensils are delicate!) You can switch the Extra Dry function on or off. There is a slight increase in energy consumption. When Eco forecast is activated, the average water and energy consumption of the selected wash cycle is briefly displayed in the digital display @ . The wash cycle time is determined during the wash cycle by the water temperature, the amount of dishes, as well as the degree of soiling and may vary (depending on the selected wash cycle). You can change the time display into time of day or hours/minutes so that the remaining cycle time of the wash cycle appears in the display window “Finish at” (for example 15:20 o’clock) or “Finish in” (for example 3:25 hours). The wash cycle sequence is optimized in Auto wash cycles with the aid of sensors. The sensors adjust the wash cycle strength of Auto wash cycles depending on the amount and type of soiling. You can adjust the sensitivity of the sensors in 3 stages. Standard: This setting is recommend for daily regular or typical use. This is the most energy efficient setting. Sensitive: This setting adjusts the wash cycle strength for the effective removal of food remnants, even if the amount of soiling is low. The energy and water consumption is increased accordingly. Very sensitive: This setting adjusts the wash cycle strength for difficult conditions of use, for example firmly dried on food remnants. This setting is recommended if using biological or eco detergents which contain lower amounts of active agents. The energy and water consumption is increased accordingly. This setting determines the length of time the control panel stays illuminated after the cycle is complete. To save energy, the recommended setting is “after one minute”. Possible settings are: ʑ off: The appliance does not switch off automatically. ʑ After one minute: The appliance switches off after 1 minute. This is the most energy efficient setting. ʑ After two hours: The appliance switches off after 2 hours. The end of the wash cycle is indicated by a buzzer. You can also change this setting. When you are operating the dishwasher, a signal sounds whenever a button is pressed. You can control the volume of the signal. If you do not like the button volume, you can switch it off. 33 en-us Operating the Dishwasher When you switch on the dishwasher, the brand logo appears. You can switch off the brand logo. You can reset all settings to the factory setting. 1. Turn the water supply on fully. 2. Open the door. 3. Switch on On/Off switch ( . The Auto wash cycle has been preset as a default whenever the appliance starts. This wash cycle remains selected if no other wash cycle button 0 is pressed. 4. Press Start button )* . 5. Close the door. Wash cycle sequence starts. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. You can delay the start of the wash cycle by up to 24 hours. Depending on the setting of the time display, the end of cycle is indicated with “Finish in” (for example 3h 25m) or “Finish at” (for example 15:20 hours). 1. Open the door. 2. Switch on On/Off switch ( . 3. Select wash cycle 0 . 4. Press Delay start button ` . 5. Keep pressing the setting buttons + - X until the displayed time corresponds with your requirements. 6. Press Start button )* , timer programming is activated. 7. To delete the Delay start time, press Start button )* for about 3 seconds. 8. Close the door. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. ® * * depending on the features of your dishwasher While the wash cycle is running, a light spot shines on the floor under the appliance door. Do not open the appliance door until the light point is no longer visible on the floor. If the appliance door is not completely closed, the light spot flashes. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. In darkened rooms, some light scattering may be visible. This is normal and cannot be changed. You can switch the Infolight on or off. 34 The EmotionLight 1" is on when the door is open irrespective of whether the or off. On/Off switch ( is switched on or off. When the door is closed, the EmotionLight is off. You can switch the EmotionLight on Note: Note that when the door is open the EmotionLight is automatically switched off after 1 hour. Operating the Dishwasher en-us CAUTION! Expansion (overpressure) may cause the appliance door to open and/or water to escape! If the door was opened on an appliance which has a hot water connection or is heated, always leave the door ajar for several minutes and then close. The wash cycle has ended when “Finished” is indicated on the digital display(s). Short time after the end of the wash cycle: 1. Press On/Off button ( . 2. Remove the dishes when they have cooled down. WARNING Risk of injury! To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot water or steam may escape. Do not fully open the door until water noises have stopped and steam has subsided. 1. Open the door. 2. Switch off On/Off switch ( . The LED’s go out. The wash cycle is saved. 3. To continue the wash cycle, switch on the On/Off switch ( again. 4. Close the door. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. 1. Open the door and press and hold the Start button )* for approximately 3 seconds until the digital display @ shows: "Program was terminated". 2. Close the door. 3. Wait about 1 minute while the dishwasher drains. 4. Open the door and press the On/Off switch ( . When the Start button ( has been pressed, the wash cycle cannot be changed. The only way a wash cycle can be changed is by terminating the wash cycle (Reset). 35 en-us Care and Maintenance Care and Maintenance A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents future problems. ʑ Check rinsing compartment for grease and limescale deposits. If you find such deposits: ʑ Fill detergent dispenser 9* with detergent. Start the appliance without utensils in the wash cycle with the highest rinsing temperature. WARNING Health hazard due to detergents containing chlorine! Always use chlorine-free detergents. NOTICE: ʑ Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any resulting damage. ʑ Do not use sponges as they could scratch the surfaces. ʑ Do not use bleach-based wipes as they could damage the surface or printing. ʑ Never use stainless steel polish on a black stainless finish or anti-fingerprint surfaces. WARNING Use caution when removing parts for cleaning as some debris may be sharp. Top off the salt and/or rinse aid as soon as the refill indicators on the fascia P and H are lit. ʑ Regularly wipe the front of the appliance with a damp cloth - water and a small amount of liquid soap is adequate. ʑ For black stainless steel and anti-fingerprint surfaces, use a soft, dry towel. For stubborn dirt, use warm water diluted with a non-abrasive, mild cleansing soap. Never use stainless steel polish. ʑ For stainless steel appliances (excluding black stainless and anti-fingerprint), use a stainless steel polish to seal and protect the surface. ʑ Clean the outer edges of the inside door panel regularly to remove debris that may collect from normal loading. If spots begin to appear on the stainless steel, make sure the rinse aid dispenser is full and functioning properly. ʑ Clean the door seal regularly with a damp cloth to remove food particles that may collect from normal loading and cause odor. A soiled door seal may not seal properly. Filter components The filter system 1Z consists of three parts. $ % & A B C Large Object Trap Prevents objects that should not be placed in your dishwasher from damaging the dishwasher pump system or clogging your household drain. Flat Fine Filter Prevents food particles from entering the wash chamber and directs particles toward the micro filter. Micro Filter Directs the smallest of particles to the household plumbing drain. 36 Cleaning intervals The filter system 1Z is designed to minimize maintenance while providing premium cleaning performance and minimum energy consumption. Depending on use habits and water hardness, the filter system will require some maintenance to sustain premium cleaning performance. Your filter system may need to be cleaned when: ʑ You notice food soils remaining on the filter system or objects trapped in the Large Object Trap. ʑ A drop in cleaning performance or a gritty film forms on the dishware. When washing normally attached food soils that have been scraped before loading, in a household that runs the dishwasher every other day, your filter should be cleaned: Cleaning interval 3- 6 times a year 8-12 times a year Usage light to average use heavy use Note: Clean the filter after washing loads with large amounts of food soils or loads with a heavy starch content to maintain optimal performance. To check or clean the filter system: 1. After each wash cycle check the filters for residue. 2. Unscrew the Large Object Trap as illustrated and remove the entire filter system. Care and Maintenance en-us 3. Remove the microfilter from the fine filter for easier cleaning. 4. Rinse the filters under running water and use a soft brush to clean. 5. Note: do not use abrasive brushes or steel wool, etc., as they may damage the filter. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align. 37 en-us Care and Maintenance Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1J . 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arm 1: (1) and remove downwards (2). 3. Remove the lower spray arm 1J upwards. Large food remnants in the rinsing water not retained by the filters may block the waste water pump. In this case: WARNING Use caution when removing parts for cleaning as some debris may be sharp. 1. Disconnect the appliance from the power supply. 2. Take out upper rack 12 and lower rack 1j . 3. Remove the filters 1Z . 4. Scoop out standing water - use a sponge if necessary. 5. Using a spoon, pry off the pump cover (as shown) until it clicks, then grip the cover and pull upward until it resists and then pull forward (1). Remove cover completely. 4. Clean spray arms under running water. 5. Re-engage or screw on spray arms. 6. Check inner compartment and remove any foreign objects. WARNING Use caution when removing parts for cleaning as some debris may be sharp. 38 7. Place pump cover in the original position (2) and press down until it engages (3). Care and Maintenance en-us NOTICE: Before leaving for vacation during warmer weather, besides turning off the main valve, also turn off water supply at the nearest point to the dishwasher. Do not leave soiled dishware in unit and leave door slightly open. During colder weather, please follow the instructions for winterizing your unit below. 8. Place cover in the original position, press down and engage. 9. Reinstall filters. 10. Re-insert racks. Note: The drain pump will not work properly if the drain pump cover is not snapped in completely until it clicks. NOTICE: If your dishwasher will be unused for a period of time in a location that experiences freezing temperatures (holiday home or through a vacation period), have your dishwasher winterized by a professional service. 39 en-us Troubleshooting Troubleshooting Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following information may help you with a dishwasher problem without involving a repair professional. Note: If the appliance stops during dishwashing or does not start for any obvious reason, first run the cancel wash cycle function (Reset). WARNING Improper repairs or use of non-original replacement parts may cause considerable damage and put the user at considerable risk! Always have repairs carried out by authorized technicians. If a component has to be replaced, always use original replacement parts. Fault Error code § : ³µ is lit. Cause Supply hose kinked. Tap turned off. Tap jammed or calcified. Some faults are indicated at the top of the display window @ and on the front display * (E22) -->Clean filters). ): and possible remedies are offered (for example Filter system soiled * optional feature which may or may not be included with your dishwasher. Filter in the water supply blocked. Remedial action Install supply hose without kinks. Turn on the tap. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Error code § : ¯Å is lit. Error code § : ³ is lit. Error code § : is lit. Error code § : is lit. Intake opening (on right inside of appliance) covered by dishes. Heating element calcified or soiled. Filters 1Z are soiled or blocked. Clean filter in the supply hose. Screw water connection on again. Check for leaks. Reconnect power supply. Switch on the appliance. Arrange dishes so that the intake opening is not obstructed. Clean appliance with dishwasher cleaning agent or descaler. Operate the dishwasher with water softening system and check the setting. Clean filters. Waste-water hose kinked or blocked. Install hose without kinks, remove any residue. Siphon connection still sealed. Cover on the drain pump loose. Check connection to siphon and open if required. Lock cover correctly. 40 Troubleshooting en-us ( Fault Error code Error code § : ¯³ to § : § § : : Å is lit. is lit. A different error code is indicated on the digital display. ´¯ ) Home network is not loading. Wi-Fi display flashes Home Connect cannot be implemented correctly. Refill indicator for salt P and/ or rinse-aid H is lit. Refill indicator for salt P and/ or rinse-aid H is not lit. Water is left in the appliance at the end of the wash cycle. Dishes not dry. Cause Drain pump blocked or cover on the drain pump is not locked in position. Mains voltage too low. Remedial action Clean pump and lock cover correctly. A technical fault has probably occurred. Wi-Fi is not active on the router. Not an appliance fault, have the mains voltage and electrical installation checked. Switch off appliances with the ON/OFF switch ( . After a short time restart the appliance. If the problem recurs, turn off the tap and pull out the mains plug. Call customer service and mention the error code. Check the wireless network connection of your router. Activate the wireless network on your router. Connection to the home network is not available. Possible setting errors or a technical fault. No rinse aid. No salt. Sensor does not detect salt tablets. Refill indicator switched off. Observe the supplied documents and support information for Home Connect. Refill rinse aid. Refill with special salt. Use different special salt. " , Water softening system / special salt" Check refill indicator, levels. There is still enough special salt/ rinse aid available. Filter system or area under the filters 1Z is blocked. Wash cycle has not ended yet. No or too little rinse aid in the dispenser. Wash cycle selected without drying. Water collecting in depressions on the dishes and silverware. Clean filters and area underneath. Wait until wash cycle ends or reset. Refill rinse aid. Select wash cycle with drying. Arrange dishes in a sloping position, arrange affected dishes as sloping as possible. " + Plastic dishes not dry. The combined detergent used has a poor drying performance extraDry to increase drying not activated. Dishes were removed too early or drying process had not ended yet. The eco rinse aid used has a limited drying performance. Special properties of plastic. Use different combination detergent with better drying performance. Use of rinse aid also increases the drying performance. Activate extraDry. Wait until wash cycle ends or wait until 30 min after wash cycle ends before removing dishes. Use a proprietary rinse aid. Eco products may have limited effectiveness. Plastic has a lower heat storage capacity and therefore dries less well. 41 en-us Troubleshooting Fault Silverware not dry. Appliance interior wet after rinse cycle. Food soils on the dishes. Dishwasher seems to run a long time Cause Silverware not arranged properly in the silverware basket. Silverware not arranged properly in the third rack. No appliance fault. Dishes placed too closely together, racks overfilled. Spray arm rotation obstructed. Remedial action Separate silverware if possible, prevent contact points. Arrange silverware properly and separate if possible. On account of the “Condensation drying” principle, water droplets are physically induced and required in the container. The humidity in the air condenses on the inner walls of the dishwasher, drains and is pumped out. Arrange dishes with adequate clearance between them ensuring that the spray jets can reach the surface of the dishes. Prevent contact points. Arrange dishes so that the spray arm can rotate without obstruction. Clean the spray arm nozzles. Clean filters. Insert and engage filters correctly. Spray arm nozzles are blocked. Filters 1Z dirty. Filters 1Z inserted incorrectly and/ or not engaged. Rinse wash cycle too weak. Dishes precleaned too intensely; sensors therefore decide on weak wash cycle sequence. Stubborn soiling cannot be completely removed. Tall narrow containers in corner areas are not rinsed adequately. Upper rack 12 on right and left not set to same height. Incoming water is not warm enough. Cycle time can vary due to soil and water conditions. Rinse aid dispenser 9" is empty. Dishwasher connected to cold water supply. Note: Check the typical wash cycle length. Select a more intensive rinse cycle. Increase sensitivity of the sensors. Do not prerinse dishes. Remove only large food soils. Increase sensitivity of the sensors. Recommended wash cycle "Regular" or Intensive. Do not place hollow containers too obliquely and do not place in the corner area. Set upper rack to same height using side levers. Before starting a cycle, run hot water faucet at the sink closest to the dishwasher. Sensors in the dishwasher automatically increase the cycle time to ensure a good wash when heavy soil is detected. Add rinse aid. Verify dishwasher is connected to hot water supply plumbing. 42 Troubleshooting en-us Fault Detergent residue. Water stains on plastic parts. Washable or water-soluble coatings in the container or on the door. White, stubborn coatings; limescale on the dishes, container or door. Cause Detergent dispenser cover blocked by dishes and therefore does not open fully. 9* Detergent dispenser cover 9* blocked by the detergent tab. Remedial action Dishes must not be placed above the detergent tab tray 1B from opening fully. . These may block the lid of the detergent dispenser and prevent it Do not place dishes or fragrance dispenser in the detergent tab tray. Detergent tab must be inserted flat and not upright. Detergent tab used in the quick or short wash cycle. Dissolving time of the detergent is not reached in the selected short wash cycle. Washing effect and dissolving performance are reduced after a prolonged storage time or detergent is very lumpy. Droplet formation on plastic surface is physically unavoidable. After drying, water stains are visible. Dissolving time of detergent tab too long for a quick or short wash cycle. Use a detergent powder or select a more intensive wash cycle. Change detergent. Use a more intensive wash cycle (more water changes). Arrange dishes in a sloping position. Use rinse aid. If required, increase softening setting. Detergent substances are deposited. These coatings cannot usually be removed with chemicals (appliance cleaner, ...). Change detergent brand. Clean appliance mechanically. If there is a “white coating” on the container floor, the water softening system has been set very low. Increase softening setting and change detergent if required. Salt dispenser cover 1R not closed. Close salt dispenser cover correctly. See “Glass and silverware damage”. Only for glasses: Initial glass corrosion – can only apparently be wiped off. Detergent substances are deposited. These coatings cannot usually be removed with chemicals (appliance cleaner, ...). Change detergent brand. Clean appliance mechanically. Hardness range incorrectly set or water hardness greater than 8.9 mmol/l. 3 in 1 detergent or bio/eco detergent not effective enough. Underdosing of detergent. Too weak rinse cycle selected. Set water softening system according to instructions for use or top up salt. Set water softening system according to instructions for use or use separate detergents (proprietary detergent, salt, rinse aid). Increase detergent dosage or change detergent. Select a more intensive rinse cycle. 43 en-us Troubleshooting Fault Tea or lipstick residue on the dishes. Colored (blue, yellow, brown), difficult to remove to non removable coatings in the appliance or on stainless steel dishes. Colored (yellow, orange, brown), easily removable deposits inside the appliance (mainly in the floor area) Discoloration of the plastic parts inside the appliance. Plastic parts discolored. Removable streaks on glasses, glasses with metallic appearance and silverware. Initial or existing, irreversible clouding of glass. Cause Too low rinsing temperature. Too little or unsuitable detergent. Remedial action Select wash cycle with higher washing temperature. Use suitable detergent at correct dosage. Dishes precleaned too intensely; sensors therefore decide on weak wash cycle sequence. Stubborn soiling cannot be completely removed. Film formation consisting of ingredients from vegetables (e.g. cabbage, celery, potatoes, noodles, ...) or the tap water (e.g. manganese). Detergent residue in the final rinse wash cycle section. Detergent dispenser cover blocked by dishes (cover does not open fully). Do not prerinse dishes. Remove only large food soils. Increase sensitivity of the sensors. Recommended wash cycle "Regular" Can be partly removed with machine cleaner or by mechanical cleaning. Coatings are harmless. Film formation caused by metallic components on silver or aluminum silverware. Film formation consisting of ingredients from food soils and substances from the tap water (limescale), “soapy” Plastic parts inside the appliance may become discolored during the service life of the dishwasher. Too low rinsing temperature. Dishes precleaned too intensely; sensors therefore decide on weak wash cycle sequence. Stubborn soiling cannot be completely removed. Too much rinse aid. Can be partly removed with machine cleaner or by mechanical cleaning. Check function of the water softening system (refill with salt) or, if using combined detergents (tablets), activate water softening system. Discoloration is normal and will not impair the function of the dishwasher. Select wash cycle with higher washing temperature. Do not prerinse dishes. Remove only large food soils. Increase sensitivity of the sensors. Recommended wash cycle "Regular" Set rinse aid amount to lower setting. No rinse aid added or setting too low. Add rinse aid and check dosage (recommended setting 4–5). Detergent dispenser cover must not be obstructed by dishes. Do not place dishes or fragrance dispenser in the detergent tab tray. Dishes precleaned too intensely; sensors therefore decide on weak wash cycle sequence. Stubborn soiling cannot be completely removed. Glasses not dishwasher-proof, only suitable for dishwasher. Do not prerinse dishes. Remove only large food soils. Increase sensitivity of the sensors. Recommended wash cycle “Regular” Use dishwasher-proof glasses. Avoid long steam phase (standing time after wash cycle ends). Use wash cycle at lower temperature. Set water softening system according to the water hardness (if required one setting lower). Use detergent with glass protection component. 44 Troubleshooting en-us Fault Rust spots on the silverware. Appliance cannot be switched on or operated. Appliance does not start. Wash cycle starts automatically. Cover on the detergent dispenser cannot be closed. Detergent residue in the detergent dispenser 9* or in the detergent tab tray 1B . Appliance stops in the wash cycle or wash cycle is interrupted. Cause Silverware not adequately rust resistant. Knife blades are frequently more severely affected. Silverware will also rust if rusting parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.). Salt content in the rinsing water too high, as salt dispenser lock not fastened firmly or salt was spilled while being refilled. Malfunction. Remedial action Use corrosion-resistant silverware. Do not wash rusting parts. Fasten salt dispenser lock firmly or remove spilled salt. Disconnect appliance from the power supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply. Check mains fuse or circuit breaker. Mains fuse may have been blown or circuit breaker tripped. Door may not be properly latched. Unit may not be turned on. Delay start may be engaged. Child lock is activated. The door may have been closed without first selecting a cycle. Power cord not inserted. The water supply may not be connected. The appliance door has not been shut properly. The door has been open for more than 4 seconds after pressing the START button. Press the main power switch to turn unit on. Shut door completely. To reset, refer to “Delay start” section in this manual. Deactivate the child lock. Refer to “Child Lock” section in this manual if applicable. Select a cycle and close the door. Ensure that the power cord is plugged all the way into the back of the appliance and into the socket. Check that the socket functions. Check and turn on water supply. Close the door. Press the START button again and close the appliance door within 4 seconds (see “Protection against unintentional operation”). Perform reset. (see “Canceling the wash cycle“). Remove detergent residue. You did not wait until wash cycle ended. Detergent dispenser or cover guide blocked by sticky detergent residue. Spray arms blocked by dishes, therefore detergent is not rinsed out. The detergent dispenser was damp when filled. Door not closed properly. Do not place dishes or fragrance dispenser in the detergent tab tray. Upper rack presses against the door and prevents door from being closed securely. Power and/or water supply interrupted. Ensure that the spray arms can rotate freely. Pour detergent into the dry detergent dispenser only. Close the door. Check whether rear panel is being pressed in, e.g. by socket or by hose holder which has not been removed. Restore power and/or water supply. 45 en-us Troubleshooting Fault Filling valves making striking noises. Knocking or rattling noise. Unusual foam formation. Cause Depends on domestic installation, as appliance is not defective. No effect on appliance function. Spray arm strikes the dishes, dishes not positioned correctly. If there is a low load, the water jets strike the washing tank directly. Remedial action No remedial action possible. Position dishes so that the spray arms do not strike the dishes. Load the appliance with more dishes or distribute the dishes more evenly in the dishwasher. Arrange light dishes securely. Light dishes move during the wash cycle. Handwash liquid in the rinse aid dispenser. Rinse aid spilled. Immediately refill rinse aid dispenser with rinse aid. Remove rinse aid with a cloth. -------- 46 Customer Service Your dishwasher requires no special care other than that described in the Care and Maintenance section of this manual. If you are having a problem with your dishwasher, before calling for service please refer to the Troubleshooting Guide section of the manual. If service is necessary, contact your dealer or installer or an authorized service center. Do not attempt to repair the appliance yourself. Any work performed by unauthorized personnel may void the warranty. If you are having a problem with your dishwasher and are not pleased with the service you have received, please take the following steps until the problem is corrected to your satisfaction: 1. Contact your installer or the Gaggenau ® authorized service provider in your area. 2. E-mail us from the customer service section of our website, www.gaggenau-usa.com 3. Call us at 877-442-4436 4. Write us: Gaggenau USA ® 1901 Main Street, Suite 600 Irvine, CA 92614 Please be sure to include your model information as well as an explanation of the problem and the date it started. You will find the model and serial number information on the label located on the edge of the dishwasher door. Please make a copy of your invoice and keep it with this manual. The customer may be required to show proof of purchase to validate warranty coverage. Customer Service en-us Statement of Limited Product Warranty The limited warranty provided by BSH Home Appliances (Gaggenau ® ) in this Statement of Limited Product Warranty applies only to the Gaggenau appliance (“Product”) sold to you, the first using purchaser, provided that the Product was purchased: ʑ for your normal, household (non-commercial) use, and has in fact at all times only been used for normal household purposes; ʑ new at retail (not a display, “as is”, or previously returned model), and not for resale, or commercial use; and ʑ within the United States or Canada, and has at all times remained within the country of original purchase. The warranties stated herein apply only to the first purchaser of the Product and are not transferable. Gaggenau reserves the right to request proof of purchase at the time any warranty claim is submitted to confirm that the Product falls within the scope of this limited product warranty. Please make sure to return your registration card; while not necessary to effectuate warranty coverage, it is the best way for Gaggenau to notify you in the unlikely event of a safety notice or product recall. Gaggenau warrants that the Product is free from defects in materials and workmanship for a period of seven hundred thirty (730) days (2 years) from the date of purchase. The foregoing timeline begins to run upon the date of purchase, and shall not be stalled, tolled, extended, or suspended, for any reason whatsoever. This Product is also warranted to be free from cosmetic defects in material and workmanship (such as scratches of stainless steel, paint/porcelain blemishes, chip, dents, or other damage to the finish of the Product), for a period of thirty (30) days from the date of purchase or closing date for new construction. This or other similar factors. This cosmetic cosmetic warranty excludes slight color variations due to inherent differences in painted and porcelain parts, as well as differences caused by kitchen lighting, product location, stock appliances. warranty specifically excludes any display, floor, “As Is”, or “B” 47 en-us Statement of Limited Product Warranty During this warranty period, Gaggenau or one of its authorized service providers will repair your Product without charge to you (subject to certain limitations stated herein) if your Product proves to have been manufactured with a defect in materials or workmanship. If a reasonable number attempts to repair the Product have been made without success, then Gaggenau will replace your Product (upgraded models may be available to you, in Gaggenau’s sole discretion, for an additional charge). All removed parts and components shall become the property of Gaggenau at its sole option. All replaced and/or repaired parts shall assume the identity of the original part for purposes of this warranty and this warranty shall not be extended with respect to such parts. Gaggenau’s sole liability and responsibility hereunder is to repair manufacturer defective Product only, using a Gaggenau-authorized service provider during normal business hours. For safety and property damage concerns, Gaggenau highly recommends that you do not attempt to repair the Product yourself, or use an unauthorized servicer; Gaggenau will have no responsibility or liability for repairs or work performed by a non-authorized servicer. If you choose to have someone other than an authorized service provider work on your Product, THIS WARRANTY WILL AUTOMATICALLY BECOME NULL AND VOID and are not agents, partners, affiliates or . Authorized service providers are those persons or companies that have been specially trained on Gaggenau products, and who possess, in Gaggenau’s opinion, a superior reputation for customer service and technical ability (note that they are independent entities representatives of Gaggenau). Notwithstanding the foregoing, Gaggenau will not incur any liability, or have responsibility, for the Product if it is located in a remote area (more than 100 miles from an authorized service provider) or is reasonably inaccessible, hazardous, threatening, or treacherous locale, surroundings, or environment; in any such event, if you request, Gaggenau would still pay for labor and parts and ship the parts to the nearest authorized service provider, but you would still be fully liable and responsible for any travel time or other special charges by the service company, assuming they agree to make the service call. Gaggenau is under no obligation, at law or otherwise, to provide you with any concessions, including repairs, pro-rates, or Product replacement, once this warranty has expired. The warranty coverage described herein excludes all defects or damage that are not the direct fault of Gaggenau, including without limitation, one or more of the following: ʑ Use of the Product in anything other than its normal, customary and intended manner (including without limitation, any form of commercial use, use or storage of an indoor product outdoors, use of the Product in conjunction with air or water-going vessels); ʑ Any party’s willful misconduct, negligence, misuse, abuse, accidents, neglect, improper operation, failure to maintain, improper or negligent installation, tampering, failure to follow operating instructions, mishandling, unauthorized service (including self performed “fixing” or exploration of the appliance’s internal workings); ʑ Adjustment, alteration or modification of any kind; ʑ A failure to comply with any applicable state, local, city, or county electrical, plumbing and/or building codes, regulations, or laws, including failure to install the product in strict conformity with local fire and building codes and regulations; ʑ Ordinary wear and tear, spills of food, liquid, grease accumulations, or other substances that accumulate on, in, or around the Product; ʑ Any external, elemental and/or environmental forces and factors, including without limitation, rain, wind, sand, floods, fires, mud slides, freezing temperatures, excessive moisture or extended exposure to humidity, lightning, power surges, structural failures surrounding the appliance, and acts of God. 48 In no event shall Gaggenau have any liability or responsibility whatsoever for damage to surrounding property, including cabinetry, floors, ceilings, and other structures or objects around the Product. Also excluded from this warranty are Products on which the serial numbers have been altered, defaced, or removed; service visits to teach you how to use the Product, or visits where there is nothing wrong with the Product; correction of installation problems (you are solely responsible for any structure and setting for the Product, including all electrical, plumbing or other connecting facilities, for proper foundation/flooring, and for any alterations including without limitation cabinetry, walls, floors, shelving, etc.); and resetting of breakers or fuses. TO THE EXTENT ALLOWED BY LAW, THIS WARRANTY SETS OUT YOUR EXCLUSIVE REMEDIES WITH RESPECT TO PRODUCT, WHETHER THE CLAIM ARISES IN CONTRACT OR TORT (INCLUDING STRICT LIABILITY, OR NEGLIGENCE) OR OTHERWISE. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED. ANY WARRANTY IMPLIED BY LAW, WHETHER FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, SHALL BE EFFECTIVE ONLY FOR THE PERIOD THAT THIS EXPRESS LIMITED WARRANTY IS EFFECTIVE. IN NO EVENT WILL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL, SPECIAL, INCIDENTAL, INDIRECT, “BUSINESS LOSS”, AND/OR PUNITIVE DAMAGES, LOSSES, OR EXPENSES, INCLUDING WITHOUT LIMITATION TIME AWAY FROM WORK, HOTELS AND/OR RESTAURANT MEALS, REMODELLING EXPENSES IN EXCESS OF DIRECT DAMAGES WHICH ARE DEFINITIVELY CAUSED EXCLUSIVELY BY BSH, OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. No attempt to alter, modify or amend this warranty shall be effective unless authorized in writing by an officer of BSH. To obtain warranty service for your Product, you should contact the nearest Gaggenau authorized service center. Installation and connection en-us Installation and connection The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation instructions. Install the appliance in the correct sequence: 1. Checking appliance on delivery 2. Installation 3. Drainage connection 4. Tap water connection 5. Electrical connection If you have any complaints, contact the dealer from whom you purchased the appliance or our customer services department. ʑ Dishwasher ʑ User manual ʑ Installation instructions ʑ Quick reference guide* ʑ Warranty* ʑ Installation materials ʑ Steam guard plate* ʑ Rubber apron* ʑ Power cord * depending on the features of your dishwasher Please refer to the Important Safety Instructions for installation that are included in the separate Installation Instructions for your appliance. 49 en-us Installation and connection Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle. ʑ Weight: up to 132 lbs (60 kg) ʑ Voltage: 120 V, 60 Hz ʑ Connected load: 1,440 W. ʑ Circuit breaker: 12 A ʑ Power input: off mode (Po)* 0.50 W. left on mode (Pl)* 50 W. in networked standby mode 2.00 W. *according to regulations (EU) nos. 1016/2010 and 1059/2010. Additional functions and settings may increase the power input. ʑ Water pressure: at least 7.25 PSI (0.5 bar), maximum 145 PSI (10 bar). At a higher water pressure: connect pressure-reducing valve ahead. ʑ Inlet rate: minimum 2.65 gallons/minute (10 liters/minute) ʑ Water temperature: Cold water. Hot water: Maximum temperature 140° F (60 °C). ʑ Capacity: 12–15 place settings (depending on the features of your dishwasher). The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor. ʑ A built-under or integrated appliance which is installed subsequently as a free-standing appliance must be secured to prevent it from overturning, e.g. by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards. ʑ The appliance can easily be installed in a fitted kitchen between wooden and plastic walls. 1. The required work sequence can be found in the installation instructions. If required, fit a siphon with a drain connection. 2. Connect the drain hose to the drain connection of the siphon with the enclosed parts. Ensure that the drain hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the drain water from flowing out! 50 1. Fasten the water supply connection to the tap according to the installation instructions using the enclosed parts. Ensure that the water supply connection is not kinked, crushed or twisted. 2. When replacing the appliance, always use a new water supply hose. Water pressure: At least 7.25 PSI (0.5 bar), maximum 145 PSI (10 bar). At a higher water pressure: connect pressure-reducing valve ahead. Inlet rate: Minimum 2.65 gallons/minute (10 liters/minute) Water temperature: Cold water. Hot water: Maximum temperature 140° F (60 °C). Installation and connection en-us Hot water connection The dishwasher can be connected to cold or hot water up to max. 140° F (60 °C). Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation, e.g. solar heating system with circulation line. This will save energy and time. The “Hot water” setting allows you to adjust your dishwasher optimally to operation with hot water. It is recommended to have a water temperature (temperature of the incoming water) of at least 104° F (40 °C) and no more than 140° F (60 °C). It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler. To change the setting: 1. Open the door. 2. Switch on ON/OFF switch ( . 3. Press Info button following text is indicated on the display window at the top @ : 8 for 3 seconds until the Scroll with < > Set with - + Leave with W 3 sec. 4. Keep pressing the button @ . > ` until water connection appears of the display window at the top 5. Make the selection with setting buttons + - X . 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. * optional feature which may or may not be included with your dishwasher. 51 en-us Installation and connection ʑ Connect the appliance to an 120 V, 60 Hz alternating current only, via a correctly installed outlet with protective grounding conductor. See rating plate for required fusing 9: . ʑ The outlet must be near the appliance and freely accessible after the installation. If the plug is not freely accessible, an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions. ʑ The connection may be modified by technicians only. ʑ A power cord extension may be purchased from customer service only. ʑ Use only a residual current operated circuit-breaker which features the symbol regulations. ‚ . Only this extension guarantees compliance with the currently valid ʑ The appliance features a water damage protection system. Please note the system will function only when the power supply is connected. Also observe the sequence of worksteps here. 1. Disconnect the appliance from the power supply. 2. Turn off the tap. 3. Undo the drain water and water supply connection. 4. Loosen fastening screws for the cabinet parts. 5. If fitted, remove the base panel. 6. Pull out the appliance, carefully pulling the hose behind. Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: 1. Turn on the tap. 2. Open the door. 3. Switch on ON/OFF button ( . 4. Select wash cycle with the highest temperature. The estimated wash cycle duration is indicated on the digital display @ . 5. Press START button )* . 6. Close the door. Wash cycle sequence starts. 7. Open the door after approx. 4 minutes. 8. Press START button the digital display )* @ . until “Program was terminated”/“Ready in one minute.” is indicated at 9. Close the door. 10. Open the door after approx. 1 minute. The digital display @ indicates; “Finished”. 11. Switch off ON/OFF switch ( . 12. Turn off the tap, disconnect supply hose and drain water. Note: Transport appliance upright only. This prevents residual water from running into the machine control and damaging the wash cycle sequence. If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see “Transporting the appliance”). 52 Safety Definitions
NOTICE:
Causes of Damage
Getting Started
Appliance overview
VHF
UHVHWVHF
Operating panel
Display indicators
Info button
Dishwasher interior components
Time setting
Switching on the appliance for the first time
Settings
Home Connect™ System
WLAN
Setting up the app
Setting up Home Connect
Network login
Connect to App
Remote start button
Wi-Fi without a connection to the Home Connect server
Remote diagnosis
Water softening system / special salt
Water hardness table
Adjusting the water softening system
Using special salt
Using detergents with salt component
Switching off low salt indicator / water softening system
Rinse Aid
Adding rinse aid
Switching off rinse aid refill indicator
Setting the amount of rinse aid used
Loading the Dishwasher Dishware material
Glass and silverware damage
Loading the racks
Loading patterns
Unloading the dishwasher
RackMatic
System
Adjusting the height of the rack
Removing/Installing third rack
Removing/Installing upper rack with Rackmatic
Rack features
Detergent
Adding detergent
Combination detergent
Dishwasher Cycles
Dishwasher Cycle Options
Intensive Zone
Extra Dry
Wash Cycle Information Turbo
Operating the Dishwasher
Protection against unintentional operation
Operating the touch buttons
Changing the settings
AquaSensor
Extra Dry
Eco forecast
Time display
Sensor setting
Auto power off
Tone volume
Button volume
Greeting
Factory setting
Switching the appliance on
Delay start time
InfoLight
EmotionLight
Interrupting the wash cycle
Wash cycle end
Switching off the appliance
Cancel a cycle (reset)
Changing the wash cycle
Care and Maintenance
Cleaning the dishwasher
Special salt and rinse aid
Filters
Spray arms
Drain pump
Preparing your unit for vacation
&OLFN
Winterizing your unit
Troubleshooting
Error message
Fault table
Customer Service
Statement of Limited Product Warranty
What this Warranty Covers & Who it Applies to:
How Long the Warranty Lasts
Repair/Replace as Your Exclusive Remedy
Out of Warranty Product
Warranty Exclusions
How to Obtain Warranty Service
Installation and connection
Parts included
Safety instructions
Delivery
Technical specifications
Installation
Drain connection
Water supply connection
Hot water connection *
Electrical connection
Removing the appliance
Transporting the appliance
Securing the appliance against frost
advertisement
Related manuals
advertisement