LIMITED WARRANTY

All equipment which is sold under ANVIL trademark and used for commercial purposes is warranted against defects in materials and workmanship. The warranty runs for two years from the date of original installation and is for the benefit of the original purchaser only. All other Warranties, expressed or implied, statutory or otherwise, including without limitations any implied Warranty of Merchantability or fitness for purpose are excluded. The Seller shall in no event be liable for direct,indirect or consequential damages in connection with ANVIL commercial products.

The Sellers obligation under this Warranty is limited to the repair of defects without charge. Defective units must be taken or shipped, transportation charges prepaid, to ANVIL.

This Warranty is not effective if damage occurs because of accident, carelessness, improper installation, lack of proper set-up,supervision when required or if the equipment is installed or operated in any manner contrary to the installation and operating instructions. In these cases,repairs will be made at a reasonable cost. Work performed by unauthorized personnel or unauthorized service agencies using non Anvil spares voids this Warranty. NB:

REGISTER ON-LINE TODAY

Register your warranty on-line now at www.anvilworld.com

NO WEB ACCESS

If you do not have access to the Web. Kindly register by completing the warranty registration form and fax it to the ANVIL office in the country of purchase.

Failure to do so will invalidate your warranty.

4-INS-DLA0002R01

DIP-A-LAIT

INSTALLATION OPERATION AND CARE OF DIP-A-LAIT MODEL: DLA0002 R01/DLA0002-120 R01

1

UNPACKING

Unpack the product and check for any damage incurred during transit. This should be reported to the responsible carrier, railway or postal authority, and a request for a damage report should be made.

THESE INSTRUCTIONS MUST BE FOLLOWED FOR US TO GUARANTEE OUR FULL SUPPORT OF YOUR CLAIM FOR PROTECTING AGAINST LOSS FROM CONCEALED DAMAGE. THE FORM FOR FILING SUCH A CLAIM WILL BE PROVIDED BY THE CARRIER.

GENERAL INSTALLATION AND OPERATION INSTRUCTIONS

1. Place the warmer into mains socket and set energy control to the high position - setting 6. The elements will burn continuously.

2. After initial warm up, set the energy control to the required heat.

Please note that the element will cycle on and off at heat settings less than maximum.

3. The warmer is equipped with one pilot light which indicates the control action of the energy control.

10

MODEL:DIP-A-LAIT MODEL CODE : DLA0002 R01

Part No.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Description

PLASTIC HANDLE NITE-LID DIP-A-LAIT INSERT DIPALAIT ELEMENT BODY ASSEMBLY CONTROL PANEL FACIA PILOT LIGHT BEZEL CONTROL KNOB CONTROL PANEL INSERT ANVIL AXIS LOGO SMALL RUBBER FEET GALVANISED BOTTOM COVER ENERGY REGULATOR CABLE GRIP POWER CORD TERMINAL BLOCK 9

WARNING

Burn Hazard

.

Do not touch hot food,liquid or heating surfaces while equipment is heating or operating Hot surfaces and food can burn skin. Allow the hot surfaces to cool before handling

CLEANING

1. Always ensure that the unit is disconnected from the main power supply before cleaning.

2. This unit should not be cleaned with a water jet or immersed in water. Use only a damp cloth or sponge dipped in soapy water.

3. Wipe off the unit with a dry cloth and wait at least a half an hour before re-connecting to the main power outlet. 2 CLEAN THE STAINLESS STEEL PARTS WITH WATER AND SOAP. AVOID THE USE OF DETERGENTS CONTAINING ABRASIVE SUBSTANCES. ALWAYS RINSE WELL AND DRY CAREFULLY AFTER CLEANING. DO NOT USE PRODUCTS CONTAINING AGGRESSIVE CHEMICALS, ACIDS OR PRODUCTS WITH CHLORINE TO CLEAN THE STAINLESS STEEL EVEN IF DILUTED

WARNING

Electric Shock Hazard

.

Keep water and other liquids from entering the inside of the equipment. Liquid inside the equipment could cause an electrical shock Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock. Do not use equipment if power cord is damaged or has been modified

SAFETY

READ ALL INSTRUCTIONS BEFORE USE. FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN INJURY TO YOURSELF AND OTHERS

1. When this appliance is to be positioned in close proximity to a wall, partitions, kitchen furniture, decorative finishes, etc.it is recommended that they be made of non-combustible material. If not, they shall be clad with a suitable non-combustible heat insulating material, and the closest attention be paid to fire prevention regulations.

2. Use the multifunction warmer on an individual 15A mains outlet only.

DO NOT OVERLOAD THE CIRCUIT.

come into contact with hot surfaces.

proximity to children.

3. Ensure that the equipment and the power supply cord does not 4. Supervision is necessary when the appliance is used in close 5. If the supply cord is damaged, it must be replaced with a new cord assembly available from the suppliers agent. The cord shall be an oil resistant sheathed flexible cable not lighter than ordinary polychloroprene or equivalent synthetic elastomer - sheathed cord (code designation 60245 IEC 57) 6. Use only earthed outlets matching the serial plate voltage.

7. Have equipment installed by a qualified personnel in accordance with local codes and ordinances.

8. Use equipment in a flat level position.

9. Do not operate unattended 10. The equipment may be hot, even though the pilot light is not on.

11. Do not operate if equipment has been damaged or is malfunc tioning in any way.

12. These units are designed to run only on alternating current (A.C.)

DO NOT CONNECT TO DIRECT CURRENT (D.C)

3

EXPLODED DIAGRAM DIP-A-LAIT DLA0002 R01

8

7

WIRING DIAGRAM MODEL CODE: DLA0002-120 R01 MODEL: DIP-A-LAIT

ER E1 H1 LEGEND DESCRIPTION ENERGY REGULATOR ELEMENT 125W/230V CONTROL PILOT LIGHT 120V N L E PART NUMBER 1-EGO-ER-120V 5-120V-125W-DIP 1-PL-BMA7102 S1 P2 ER P1 S2 4 E1 H1 2

POSITIONING DIAGRAM DIP-A-LAIT DLA0002 R01 307mm

4

ELECTRICAL CONNECTION INFORMATION

MODEL DLA0002 R01 DESCRIPTION DIP-A-LAIT VOLTS (V /Hz) 230/50 DLA0002-120 DIP-A-LAIT 120/60 POWER (W) 125 125 5 IT IS ESSENTIAL TO MAKE SURE THAT THE INCOMING VOLTAGE IS THE SAME AS THE RATED VOLTAGE OF THE OF THE UNIT AS FOUND ON THE SERIAL PLATE. THE SERIAL PLATE IS LOCATED AT THE REAR OF THE UNIT ADJACENT TO THE INCOMING CABLE ENTRY.

WIRING DIAGRAM MODEL CODE: DLA0002 R01 MODEL: DIP-A-LAIT

ER E1 H1 LEGEND DESCRIPTION ENERGY REGULATOR ELEMENT 125W/230V CONTROL PILOT LIGHT 6 PART NUMBER 1-ER-URS0012 5-125W-DIPALAY 1-PL-BMA0001 N S1 P2 ER P1 L E S2 4 2 E1 H1