Simrad NSS9 evo2 Benutzerhandbuch
Add to my manuals
1 Pages
Simrad NSS9 evo2 is a high-performance fishfinder and chartplotter designed to provide anglers and boaters with a powerful tool for navigating and finding fish. With its 9-inch display, the NSS9 evo2 offers a clear and detailed view of charts, sonar images, and other data. Its built-in GPS receiver provides accurate positioning and allows you to create and follow routes and waypoints. The NSS9 evo2 also supports a variety of transducers, including CHIRP sonar, StructureScan 3D, and ForwardScan, providing you with a variety of options for finding fish and underwater structures.
advertisement
◉
Touch to zoom
ZEUS² 9 NSS9 evo2 Check dimensions before cutting NOTE: 12" DO NOT SCALE PRINT 1:1 300 mm 142.3 mm (5.60") 142.3 mm (5.60") 139.8 mm (5.50") 139.8 mm (5.50") 135.0 mm (5.31") 135.0 mm (5.31") 131.0 mm (5.16") 131.0 mm (5.16") *988-10606-002* 21.5 mm (0.85") 110.0 mm (4.33”) 84.0 mm (3.31") 69.3 mm (2.73") 73.5 mm (2.89") 81.75 mm (3.22") 84.3 mm (3.32") 73.5 mm (2.89") 81.75 mm (3.22") 84.3 mm (3.32") Product Outline CL 138.5 mm (5.45") 147.0 mm (5.79") 163.5 mm (6.44") 168.5 mm (6.63") (see note) 69.3 mm (2.73") CL Protective Cover 8.0 mm (5/16") 262.0 mm (10.31") 270.0 mm (10.63") 279.5 mm (11.00") 284.5 mm (11.20") Important drill bit size selection information IMPORTANT. Do not use this template if it has been rescaled by copying or printing. If this is not the original, or is a print from a file, please check the dimension lines below are to scale before use. IMPORTANT. Ne pas utiliser ce gabarit s’il a été photocopié ou imprimé en format réduit ou agrandi. Si ce gabarit n’est ni un original ni une version imprimée d’un fi chier PDF, veuillez vérifi er qu’il est à l’échelle avant de l’utiliser. IMPORTANTE. No usar la plantilla si hay peligro que la escala original exacta se ha alterado por copias o procesos de impresión imprecisos. Si esta no es la original, o un PDF, verifique que las líneas de abajo están a la escala antes de usar. WICHTIG. Diesen Vordruck nicht verwenden, wenn er durch Kopieren oder Drucken im Maßstab verändert wurde. Sollte es nicht das Original oder ein PDF-Ausdruck sein, müssen untenstehende Zeilen vor erwendung an den richtigen Maßstab angepasst werden. BELANGRIJK. Gebruik deze mal niet indien de schaal is veranderd doordat het is gecopieerd of gedrukt. Indien deze mal niet het origineel of een print van PDF is, controleer dan of de onderstaande lijnen de juiste schaal zijn voordat u ze gebruikt. IMPORTANTE. Não utilize este gabarito se a escala do mesmo tiver sido alterada por cópia ou impressão. Se não for o original ou uma cópia impressa de um arquivo PDF, verifi que as linhas abaixo, para acertar a escala antes da utilização. VIKTIGT. Använd inte denna mall om den skalats om genom utskrift eller kopiering. Om detta inte är originalet eller en utskrift från en PDF, kontrollera att linjerna nedan stämmer med skalan innan det används. IMPORTANTE. Non utilizzare questo modello se è stato ridimensionato copiandolo o stampandolo. Se questo non è l’originale o è stampato da un file PDF, verificare che le dimensioni siano prima di utilizzarlo. TÄRKEÄÄ. Älä käytä tätä kaaviota, jos sen mittakaava on muuttunut kopio-idessa tai tulostaessa. Jos tämä ei ole alkuperäinen tai PDF tuloste tarkista rajat mittakaavasta alla ennen käyttöä. Soft materials e.g. Plywood 1.9 - 2.3 mm (5/64") Hard materials e.g. GRP, Acrylic, hardwoods 2.3 - 2.5 mm (3/32") 注意:请尽量不要使用本安装挖孔尺寸模版图的复印件。如果使用复印件,则在 使用之前请确认其比例一定要与原件大小必须一致。 중요: 복사나 출력으로 크기가 조정 된 경우 이 템플릿을 사용하지 마십시오. 원본이 아니거나 인쇄물이면, 사용하기 전 아래 치수선의 눈금을 확인 해 주십시오. 注:このテンプレートは印刷やコピーによって縮尺が変わっていることがあり ますので使用しないで下さい。テンプレートがオリジナルのものでない場合に は、下の寸法線を使って縮尺を確認してください。 ВНИМАНИЕ: Не используйте эту инструкцию, если она была измене на в размерах при копировании или распечатке. Если вы используе те не оригинал, а распечатку из файла, убедитесь в соответствии размеров линейки в нижней части инструкции с действительными размерами. Front mount screw recommendation Max 5.5 mm (0.22”)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project