advertisement
User Manual
U32R59*
The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than that of Samsung Electronics are owned by their respective owners.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e., where the user manual has not been read).
(b) You bring the unit to a repair center, but it is found that the product has no defect (i.e., where the user manual has not been read).
You will be informed of the administration fee amount before a technician visits.
Table of contents
Before Using the Product
Securing the Installation Space
Preparations
Configuring Eye Saver Mode, Brightness and Contrast from the Initial Screen 14
Precautions for moving the monitor
Connecting and Using a Source Device
Read below before installing the monitor.
Connection Using the HDMI Cable
Connection Using the HDMI-DVI Cable
Tidying Up the Connected Cables
Correct posture to use the product
Picture
2
Table of contents
PBP
OnScreen Display
System
Installing the Software
Restrictions and Problems with the Installation 36
Troubleshooting Guide
Requirements Before Contacting Samsung Customer
Checking the Resolution and Frequency
Specifications
Appendix
Responsibility for the Pay Service (Cost to
A Product damage caused by customer's fault 44
3
Chapter 01
Before Using the Product
Securing the Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product.
―
The exterior may differ depending on the product.
Safety Precautions
Warning
Caution
A serious or fatal injury may result if instructions are not followed.
Personal injury or damage to properties may result if instructions are not followed.
10 cm (3.93 Inches)
10 cm (3.93 Inches)
10 cm
(3.93 Inches)
10 cm
(3.93 Inches)
10 cm
(3.93 Inches)
Precautions for storage
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby.
―
Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product
(Service fee will be charged.)
Do not press the monitor screen with hands or other objects. There is a risk of damaging the screen.
4
Cleaning
―
Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
―
Take the following steps when cleaning.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
―
Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result.
3 Wipe the monitor with a clean, soft and dry cloth.
‒ Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
‒ Do not spray water or detergent directly on the product.
4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5 Connect the power cord to the product when cleaning is finished.
6 Power on the product and computer.
Electricity and Safety
Warning
• Do not use a damaged power cord or plug, or a loose power socket.
• Do not use multiple products with a single power socket.
• Do not touch the power plug with wet hands.
• Insert the power plug all the way in so it is not loose.
• Connect the power plug to a grounded power socket (type 1 insulated devices only).
• Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy object.
• Do not place the power cord or product near heat sources.
• Clean any dust around the pins of the power plug or the power socket with a dry cloth.
Caution
• Do not disconnect the power cord while the product is being used.
• Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.
• Keep the power socket where the power cord is connected unobstructed.
‒ The power cord must be disconnected to cut off power to the product when an issue occurs.
• Hold the plug when disconnecting the power cord from the power socket.
5
Installation
Warning
• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
• Do not install the product in poorly ventilated spaces such as a bookcase or closet.
• Install the product at least 10 cm away from the wall to allow ventilation.
• Keep the plastic packaging out of the reach of children.
‒ Children may suffocate.
• Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
‒ The product may fall and become damaged and/or cause an injury.
‒ Using the product in an area with excess vibration may damage the product or cause a fire.
• Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke.
• Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
‒ The product lifespan may be reduced or a fire may result.
• Do not install the product within the reach of young children.
‒ The product may fall and injure children.
• Edible oil (such as soybean oil) may damage or distort the product. Keep the product away from oil pollution. And do not install or use the product in the kitchen or near the kitchen stove.
Caution
• Do not drop the product while moving.
• Do not set down the product on its front.
• When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.
‒ The product may fall and become damaged and/or cause an injury.
‒ Install the product only on cabinets or shelves of the right size.
• Set down the product gently.
‒ Product failure or personal injury may result.
• Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances, extreme temperatures or a significant presence of moisture, or a place where the product will operate continuously for an extended period of time) may seriously affect its performance.
‒ Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
6
Operation
Warning
• There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
‒ Contact Samsung Customer Service Center for repairs.
• To move the product, first disconnect all the cables from it, including the power cable.
• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Center.
• Do not let children hang from the product or climb on top of it.
‒ Children may become injured or seriously harmed.
• If the product is dropped or the outer case is damaged, turn off the power and disconnect the power cord. Then contact Samsung Customer Service Center.
‒ Continued use can result in a fire or electric shock.
• Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
‒ The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury.
• During a lightning or thunderstorm, power off the product and remove the power cable.
• Do not drop objects on the product or apply impact.
• Do not move the product by pulling the power cord or any cable.
• If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
• Do not lift or move the product by pulling the power cord or any cable.
• Do not use or keep combustible spray or an inflammable substance near the product.
• Ensure the vents are not blocked by tablecloths or curtains.
‒ An increased internal temperature may cause a fire.
• Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/output ports, etc).
‒ Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center.
• Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.
‒ Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center.
7
Caution
• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
‒ Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time.
• Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).
‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
• Use the product at the recommended resolution and frequency.
‒ Your eyesight may deteriorate.
• Do not put AC/DC adapters together.
• Remove the plastic bag from the AC/DC adapter before you use it.
• Do not let water enter the AC/DC adapter device or get the device wet.
‒ An electric shock or fire may result.
‒ Avoid using the product outdoors where it can be exposed to rain or snow.
‒ Be careful not to get the AC/DC adapter wet when you wash the floor.
• Do not put the AC/DC adapter near to any heating apparatus.
‒ Otherwise, a fire may result.
• Keep the AC/DC adapter in a well-ventilated area.
• If you place the AC/DC power adapter so that it is hanging with the cord input facing upwards, water or other foreign substances could enter the Adapter and cause the Adapter to malfunction.
Make sure to rest the AC/DC power adapter flat on a table or the floor.
• Insert the power plug into the AC/DC adapter until a click sound is heard.
• Do not insert only the power plug into the power outlet.
• Do not use an AC/DC adapter other than the provided one.
‒ It may cause electric shock or fire.
• Do not insert the AC/DC adapter into the power outlet on the ceiling.
‒ It may cause electric shock or fire.
• Rotate the power plug not to exceed the range (0 to 90°) on the AC/DC adapter.
‒ It may cause electric shock or fire.
• Never diassemble the power plug after being assembled. (It cannot be separated after assembly.)
• Never use the provided power plug for other devices.
• When removing the AC/DC adapter from the power outlet, hold the body of AC/DC adapter and pull it up.
‒ It may cause electric shock or fire.
• Do not drop any objects or apply shock on the AC/DC adapter.
‒ It may cause electric shock or fire.
• Use the AC/DC adapter after removing its plastic cover.
‒ Otherwise, this may result fire.
8
• Do not hold the product upside-down or move it by holding the stand.
‒ The product may fall and become damaged or cause an injury.
• Looking at the screen too close for an extended period of time can deteriorate your eyesight.
• Do not use humidifiers or stoves around the product.
• Rest your eyes for more than 5 minutes or look at distance objects for every 1 hour of product use.
• Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
• Store small accessories out of the reach of children.
• Exercise caution when adjusting the product angle.
‒ Your hand or finger may get stuck and injured.
‒ Tilting the product at an excessive angle may cause the product to fall and an injury may result.
• Do not place heavy objects on the product.
‒ Product failure or personal injury may result.
• When using headphones or earphones, do not turn the volume too high.
‒ Having the sound too loud may damage your hearing.
9
Chapter 02
Preparations
Parts
Control Panel
―
The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Power LED
JOG Button
UP
Function Key Guide
Icons
JOG Button
Power LED
Function Key Guide
Description
Multi directional button that helps navigate.
―
The JOG button is located on the rear left side of the product. The button can be used to move up, down, left or right, or as Enter.
This LED is power status indicator and works as
• Power On (Power button): Off
• Power saving mode: Blinking
• Power Off (Power button): On
―
The power Indicator operation can be swapped by changing in the menu. ( System → Power LED On ) Actual models because of functional variation maybe haven’t this function.
Press the JOG button when the screen is turned on. The Function Key
Guide will appear. To access the onscreen menu when the guide is displayed, press the corresponding direction button again.
―
Function Key Guide may vary depending on the function or product model. Please refer to the actual product.
LEFT RIGHT
Return
PRESS(ENTER)
DOWN
10
Direct Key guide
―
The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned on, the computer resolution changes, or the input source changes.
Eye Saver Mode
Volume
Features
Eye Saver Mode Off
• UP/DOWN: Adjust Brightness , Contrast , Eye Saver Mode .
• LEFT/RIGHT: Adjust Volume .
• PRESS(ENTER): Display Function Key Guide.
11
Function Key Guide
―
To enter the main menu or to use other items, press the JOG button to display the Function Key Guide. You can exit by pressing the JOG button again.
UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes.
PRESS(ENTER): The selected item will be applied.
Return
Icons Description
Selects to change the input signal by moving the JOG button in the Function Key Guide screen. A message will appear on the top left corner of the screen if the input signal has been changed.
―
When PBP Mode is available, the position of left and right sides of screen can be changed by using this key.
Selects by moving the JOG button in the function key guide screen.
The OSD (On Screen Display) of your Monitor’s feature appears.
OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings.
Enable/Disable: To lock/unlock the OSD control, press the LEFT button for 10 seconds when the main menu displayed.
―
If the OSD control is locked, Brightness and Contrast can be adjusted. PBP is available.
Eye Saver Mode is available. Information can be viewed.
Selects by moving the JOG button in the function key guide screen.
Press the button when configuring settings for the PBP function is required.
Selects to turn the Monitor off by moving the JOG button in the function key guide screen.
―
Actual models because of functional variation, Function key guide options will be different.
12
When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control source and power could be used as below.
JOG Button
UP
Down
PRESS(ENTER) for 2 seconds
Power saving/Non-signal mode
Source Change
Power Off
When the monitor displays the Main menu the JOG Button could be used as below.
JOG Button
UP/DOWN
LEFT
RIGHT
PRESS(ENTER)
Action
Move the option
Exit the Main menu.
Close Sublist without saving value.
Value decreases in the slider.
Move to next depth.
Value increases in the slider.
Move to next depth.
Save the value and close Sublist.
13
Configuring Eye Saver Mode, Brightness and Contrast from the Initial Screen
Adjust the Brightness , Contrast and Eye Saver Mode by moving the JOG button.
Contrast
Eye Saver Mode
Brightness
Off
―
The displayed image may differ depending on the model.
―
The default brightness can vary depending on the region.
Eye Saver Mode
Brightness
―
This menu is not available when Bright is set to Dynamic Contrast mode.
―
This menu is not available when Eye Saver Mode is enabled.
Contrast
―
This menu is not available when Bright is in Cinema or Dynamic Contrast mode.
―
This menu is not available when Game Mode is enabled.
―
This menu is not available when PBP Mode is set to On .
Changing the Volume setting
You can adjust Volume by moving the JOG button left or right, if no OSD menu is displayed.
Volume 50
Mute
―
The displayed image may differ depending on the model.
―
If the audio quality of a connected input device is poor, the Auto Mute function on the product may mute the sound or cause choppy audio when applying the headphones or speakers. Set the input volume for the input device to at least 20% and control the volume using the volume control (JOG button LEFT/RIGHT) on the product.
―
What is Auto Mute?
The function mutes the audio to improve sound effect when there is sound noise or when the input
― signal is weak, usually due to a problem with the volume of an input device.
To activate the Mute function, access the Volume control screen, then use the JOG button to move the focus down. To deactivate the Mute function, access the Volume control screen, then increase or decrease the Volume .
14
Types of Ports
―
The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Refer to the actual product.
Port
HDMI IN
DP IN
DC 19V
Description
Connects to a source device using an HDMI cable or HDMI-DVI cable.
―
HDMI support 3840 x 2160 @ 60 Hz
Connects to a PC using a DP cable.
Connect to an audio output device such as headphones.
―
The sound could only be heard when using the HDMI to HDMI cable or DP cable.
Connects to the AC/DC adapter.
HDMI IN DP IN DC 19V
15
Adjusting the Product Tilt
―
The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
-1.0° (-2.0° ~ +1.0°) ~ 17.0° (±2.0°)
Anti-theft Lock
―
An anti-theft lock allows you to use the product securely even in public places.
―
The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
To lock an anti-theft locking device:
• The monitor tilt can be adjusted.
• Hold the lower part of the product and adjust the tilt carefully.
1 Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2 Put one end of the cable through the loop on the other end.
3 Insert the locking device into the anti-theft lock slot at the back of the product.
4 Lock the locking device.
‒ An anti-theft locking device can be purchased separately.
‒ Refer to the user guide provided with your anti-theft locking device for details.
‒ Anti-theft locking devices can be purchased at electronics retailers or online.
16
Precautions for moving the monitor
• Do not directly apply pressure on the screen.
• Do not hold the screen when moving the monitor.
• Do not hold the product upside down only by the stand.
• Hold the lower corners or edges of the monitor when moving it.
17
Installation
Attaching the Stand
―
Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
―
The exterior may differ depending on the product.
1 2 3
Insert the stand neck into the stand base in the direction shown in the figure.
Check that the stand neck is firmly connected.
4
Tightly fasten the connecting screw at the bottom of the stand base.
Place the protective Styrofoam (cushion) included in the package on the floor and place the product facing down on the Styrofoam, as shown in the image.
If Styrofoam is unavailable, use a thick sitting mat.
Place the assembled stand into the main body in the direction of the arrow as shown in the figure.
5
Fasten the screws at the bottom of the stand neck. Tide up the connected power supply and the data cable then cover the COVER-REAR SUB as shown in the figure.
- Caution
Do not press down on the monitor. There is a risk of damaging the monitor.
18
Removing the Stand
―
Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down.
―
The exterior may differ depending on the product.
1 2 3
Place the protective Styrofoam (cushion) included in the package on the floor and place the product facing down on the Styrofoam, as shown in the image.
If Styrofoam is unavailable, use a thick sitting mat.
Unfasten the 2 screws at the bottom of the stand neck.
4
Lift and remove the stand in the direction of the arrow as shown in the figure.
Remove the stand neck from the stand base by pulling it in the direction of the arrow as shown in the figure.
- Caution
Do not press down on the monitor. There is a risk of damaging the monitor.
19
Chapter 03
Connecting and Using a Source Device
Read below before installing the monitor.
1 Check the shapes of both ends of the cables that came with the monitor, and check the shapes and positions of the matching ports on the monitor and external devices.
2 Before connecting signal cables, disconnect the power cables for the monitor and external devices from the power outlet to prevent device damage from a short circuit or overcurrent.
3 After connecting all signal cables, connect the power cables for the monitor and external devices to the power outlet.
4 Read the user manual to familiarize yourself with the monitor functions, precautions, and proper use, before using the installed monitor.
Connecting and Using a PC
Select a connection method suitable for your PC.
―
Connecting parts may differ in different products.
―
Provided ports may vary depending on the product.
Connection Using the HDMI Cable
Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet.
HDMI IN
―
To display 3840 x 2160 @ 60 Hz, use an HDMI cable that supports 3840 x 2160 @ 60 Hz to connect HDMI.
Make sure that the graphics card of the HDMI source supports 3840 x 2160 @ 60 Hz.
―
When connecting an HDMI cable, use the cable that came with the components of the monitor. If you use an HDMI cable other than provided by Samsung, the image quality may be degraded.
20
Connection Using the HDMI-DVI Cable
Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet.
HDMI IN
Connecting to Headphones
―
Use headphones when activating sound with an HDMI-HDMI or DP cable.
―
The earphone jack supports only the 3 conductor tip-ring-sleeve (TRS) type.
―
The audio function is not supported if the source device is connected using the HDMI-DVI cable.
―
The optimum resolution may not be available with an HDMI-DVI cable.
Connection Using the DP Cable
Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet.
DP IN
―
To display 3840 x 2160 @ 60 Hz, use a DP cable that supports 3840 x 2160 @ 60 Hz. Make sure that the graphics card of the DP source supports 3840 x 2160 @ 60 Hz.
21
Connecting the Power
1
2 DC 19V
3
4
1 Connect the power plug to the AC/DC adapter.
2 Connect the AC/DC adapter cable to the DC 19V port on the back of the monitor.
3 Plug the AC/DC adapter into the power outlet.
4 Press the JOG button on the back of the monitor to turn it on.
―
The input voltage is switched automatically.
―
In some areas, installation of an additional power plug is not necessary.
Tidying Up the Connected Cables
1
4
2
5
3
6
22
Correct posture to use the product Driver Installation
―
You can set the optimum resolution and frequency for this product by installing the corresponding drivers.
―
To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com.
Use the product in the correct posture as follows:
• Straighten your back.
• Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen.
• Keep your eyes directly in front of the screen.
• Adjust the angle so light does not reflect on the screen.
• Keep your forearms perpendicular to your upper arms and level with the back of your hands.
• Keep your elbows at about a right angle.
• Adjust the height of the product so you can keep your knees bent at 90 degrees or more, your heels attached to the floor, and your arms lower than your heart.
• Do the Eye excercises or blink frequently, then eye fatigue will be relieved.
Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for the first time after purchase.
Select a language on the product and change the resolution on your PC to the optimum setting.
―
If the optimum resolution is not selected, the message will appear up to three times for a specified time
― even when the product is turned off and on again.
The optimum resolution can also be selected in Control Panel on your PC.
23
Chapter 04
Picture
Configure the screen settings such as brightness.
A detailed description of each function is provided. Refer to your product for details.
―
The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
SAMSUNG MAGIC Bright
This menu provides an optimum picture quality suitable for the environment where the product will be used.
―
This menu is not available when Game Mode is enabled.
―
This menu is not available when Eye Saver Mode is enabled.
―
Not available when PBP Mode is set to On .
You can customize the brightness to suit your preferences.
In PC mode
• Custom : Customize the contrast and brightness as required.
• Standard : Obtain a picture quality suitable for editing documents or using Internet.
• Cinema : Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content.
• Dynamic Contrast : Obtain balanced brightness through automatic contrast adjustment.
In AV mode
When the external input is connected through HDMI/DP and PC/AV Mode is set to AV , Bright has four automatic picture settings ( Dynamic , Standard , Movie and Custom ) that are preset at the factory. You can activate either Dynamic , Standard , Movie or Custom . You can select Custom which automatically recalls your personalized picture settings.
• Dynamic : Select this mode to view a sharper image than in Standard mode.
• Standard : Select this mode when the surroundings are bright. This also provides a sharp image.
• Movie : Select this mode when the surroundings are dark. This will save power and reduce eye fatigue.
• Custom : Select this mode when you want to adjust the image according to your preferences.
24
Brightness
You can adjust the general brightness of the picture. (Range: 0~100)
A higher value will make the picture appear brighter.
―
This menu is not available when Bright is set to Dynamic Contrast mode.
―
This menu is not available when Eye Saver Mode is enabled.
Contrast
Adjust the contrast between the objects and background. (Range: 0~100)
A higher value will increase the contrast to make the object appear clearer.
―
―
This option is not available when
This menu is not available when
Bright
Game Mode
is in Cinema
is enabled.
or Dynamic Contrast mode.
―
This menu is not available when PBP Mode is set to On .
Sharpness
Make the outline of objects more clear or blurry. (Range: 0~100)
A higher value will make the outline of objects clearer.
―
―
This option is not available when
This menu is not available when
Bright
Game Mode
is in Cinema
is enabled.
or Dynamic Contrast mode.
―
Not available when PBP Mode is set to On .
Color
Adjust the tint of the screen.
―
―
This menu is not available when Bright is set to Cinema or Dynamic Contrast mode.
This menu is not available when Game Mode is enabled.
―
This menu is not available when Eye Saver Mode is enabled.
―
Not available when PBP Mode is set to On .
• Red : Adjust the red saturation level. Values closer to 100 mean greater intensity for the color.
• Green : Adjust the green saturation level. Values closer to 100 mean greater intensity for the color.
• Blue : Adjust the blue saturation level. Values closer to 100 mean greater intensity for the color.
• Color Tone : Select a color tone that best suits your viewing needs.
‒ Cool 2 : Set the color temperature to be cooler than Cool 1 .
‒ Cool 1 : Set the color temperature to be cooler than Normal mode.
‒ Normal : Display the standard color tone.
‒ Warm 1 : Set the color temperature to be warmer than Normal mode.
‒ Warm 2 : Set the color temperature to be warmer than Warm 1 .
‒ Custom : Customize the color tone.
―
When the external input is connected through HDMI/DP and PC/AV Mode is set to AV , Color Tone has four color temperature settings ( Cool , Normal , Warm and Custom ).
• Gamma : Adjust the middle level of luminance.
‒ Mode1 / Mode2 / Mode3
25
SAMSUNG MAGIC Upscale
Upscale function can enhance the layers of the picture details and the vividness of the picture.
The function has more obvious effects on low-resolution pictures.
―
This menu is not available when Bright is set to Cinema or Dynamic Contrast mode.
―
This menu is not available when Game Mode is enabled.
―
Not available when PBP Mode is set to On .
• Off / Mode1 / Mode2
―
Comparing with Mode1 , Mode2 has a stronger effect.
Eye Saver Mode
Set to an optimum picture quality suitable for eye relaxation.
TÜV Rheinland “Low Blue Light Content” is a certification for products which meet requirements for lower blue light levels. When Eye Saver Mode is ' On ', the blue light that wavelength is around 400nm will decrease, and it will provide an optimum picture quality suitable for eye relaxation. At the same time, the blue light level is lower than in the default settings, and it was tested by TÜV Rheinland and certified as it met the requirements of TÜV Rheinland “Low Blue Light Content” standards.
HDMI Black Level
If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/ color degradation, black level, etc.) may occur, depending on the connected source device. In such case,
HDMI Black Level can be used to adjust the image quality.
If this is the case, correct the degraded picture quality using HDMI Black Level .
―
This function is only available in HDMI mode.
―
Not available when PBP Mode is set to On .
• Normal : Select this mode when there is no contrast ratio degradation.
• Low : Select this mode to reduce the black level and increase the white level when there is a contrast ratio degradation.
―
HDMI Black Level may not be compatible with some source devices.
―
The HDMI Black Level feature is only activated at a certain AV resolution, such as 720P @ 60 Hz and 1080P
@ 60 Hz.
Game Mode
Configure the product screen settings for game mode.
Use this feature when playing games on a PC or when a game console such as PlayStation™ or Xbox™ is connected.
―
This menu is not available when Eye Saver Mode is enabled.
―
When the monitor turns off, enters power-saving mode or changes input sources, Game Mode turns Off
― even if it is set to On .
If you want to keep Game Mode enabled all the time, select Always On .
―
Not available when PBP Mode is set to On .
Response Time
Accelerate the panel response rate to make video appear more vivid and natural.
―
Use Standard mode when not playing a video or game.
26
Picture Size
Change the picture size.
―
This menu is not available when PBP Mode is set to On .
In PC mode
• Auto : Display the picture according to the aspect ratio of the input source.
• Wide : Display the picture in full screen regardless of the aspect ratio of the input source.
In AV mode
• 4:3 : Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
• 16:9 : Display the picture with an aspect ratio of 16:9.
• Screen Fit : Display the picture with the original aspect ratio without cutting off.
―
The function may not be supported depending on the ports provided with the product.
―
Changing the screen size is available when the following conditions are satisfied.
―
A digital output device is connected using the HDMI/DP cable.
―
The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally (Not every model can support all of these signals.).
―
This can only be set when the external input is connected through HDMI/DP and PC/AV Mode is set to
AV .
Screen Adjustment
―
This menu is only available when Picture Size is set to Screen Fit in AV Mode.
When a 480P or 576P or 720P or 1080P signal is input in AV mode and the monitor can display normally, select Screen Fit to adjust horizontal position in 0-6 levels.
Configuring H-Position & V-Position
H-Position : Move the screen to the left or right.
V-Position : Move the screen up or down.
27
Chapter 05
PBP
A detailed description of each function is provided. Refer to your product for details.
―
The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
PBP Mode
Enable or disable the PBP Mode function.
The PBP (Picture by Picture) function separates the screen in half displaying output from two different source devices simultaneously on the left and right sides of the screen.
―
The optimum resolution for the left and right sides of the screen is 1920 x 2160 (width x height).
―
PBP mode is compatible with Windows 7, Windows 8, and Windows 10.
―
The PBP function may not be available depending on the specifications of the graphics card used. If the screen is blank in PBP mode when the optimum resolution is selected, go to Control Panel → Display →
Screen Resolution and click Detect on the PC. (Instructions are based on Windows 7.) If the screen is blank
― when the resolution is set to the optimum resolution, change the resolution to 1280 x 1024.
The screen may flicker briefly or appear after a delay when you enable or disable the PBP function or when you change the screen size with the PBP function activated.
This can typically arise when a PC and a monitor are connected to two or more input sources. It has nothing to do with the performance of a monitor.
The issue is mainly caused when the video signals are delayed in transmission to the monitor depending on the graphics card performance.
―
To maximize the picture quality and Sound can be normal output it is recommended to use a graphics card or DVD that supports 4K (3840 x 2160 @ 60 Hz) resolution when connect HDMI port.
―
When the PBP function is enabled, the resolution will not be able to automatically switch to the optimum resolution due to a compatibility issue between the graphics card and the Windows system.
Set PBP Mode to Off . Alternatively, restart the monitor, then set the resolution to the optimum setting using the Windows interface.
28
Sound Source
Set which screen you want to hear the sound for.
• /
Picture Size
Set the Picture Size for each of the divided screens.
In PC mode
• Auto : Display the picture according to the aspect ratio of the each screen input source.
• Wide : Display the picture in full screen regardless of the aspect ratio of the each screen input source.
In AV mode
• 4:3 : Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
• 16:9 : Display the picture of the sub-screen with an aspect ratio of 16:9.
• Screen Fit : Display the picture of the sub-screen with the original aspect ratio without cutting anything off.
―
The function may not be supported depending on the ports provided with the product.
―
Changing the screen size is available when the following conditions are satisfied.
―
A digital output device is connected using the HDMI/DP cable.
―
The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally (Not every model can support all of these signals.).
―
This can only be set when the external input is connected through HDMI/DP and PC/AV Mode is set to
AV .
Contrast
Adjust the contrast level for each screen.
29
Chapter 06
OnScreen Display
A detailed description of each function is provided. Refer to your product for details.
―
The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Transparency
Set the transparency for the menu windows.
Language
Set the menu language.
―
A change to the language setting will only be applied to the onscreen menu display.
―
It will not be applied to other functions on your PC.
Display Time
Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified period of time.
Display Time can be used to specify the time after which you want the OSD menu to disappear.
30
Chapter 07
System
A detailed description of each function is provided. Refer to your product for details.
―
The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
2 Select OK when the following screen is prompted.
The test screen will now be shown. Please look carefully at the screen for the next 10 seconds.
Self Diagnosis
1 Use the function key and go to → System → Self Diagnosis .
System
Self Diagnosis
Smart ECO Saving+
Off Timer Plus
PC/AV Mode
DisplayPort Ver.
HDMI Mode
Source Detection
Off
1.2↑
2.0
Auto
Perform this test when you experience a problem with your monitor's picture.
Return
―
The displayed image may differ depending on the model.
• Review the test screen.
OK
31
3 Base on the test result, select Yes / No .
Do you still see the same problem on the test screen?
Yes No
• You will see the following screen when you select Yes .
Self Diagnosis Complete
Contact the Samsung Call Center for assistance.
Please have the following information ready:
‐ Model Code: **************
‐ S/N: **************
OK
• You will see the following screen when you select No .
Self Diagnosis Complete
If the test screen is okay during Self Diagnosis, your monitor may not have a problem. If the problem persists, follow the steps below:
‐ Turn off your monitor and any other connected device, such as a PC. Turn on your monitor first and then the other connected device.
‐ Update the operating system and graphics card driver to the latest version and restart your PC.
‐ Connect the other device, such as a PC, to a different input port on your monitor.
‐ Reset your monitor by pressing the jog button on the monitor and selecting System > Reset All.
Replace the cable with the one enclosed with your monitor.
OK
32
Smart ECO Saving+
The Smart ECO Saving+ function reduces power consumption by controlling the electric current used by the monitor panel.
―
This menu is not available when Eye Saver Mode is enabled.
―
This menu is not available when Game Mode is enabled.
―
This menu is not available when PBP Mode is enabled.
―
This menu is not available when Bright is set to Dynamic Contrast mode .
• Off : Deactivate the Smart ECO Saving+ function.
• On : The power consumption will be adjusted to save energy automatically. (The reduction of power consumption depends on the customer screen brightness condition.)
Off Timer Plus
Configuring Off Timer
Off Timer : Turn on Off Timer mode.
Turn Off After : The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours.
―
This option is only available when Off Timer is set to On .
―
For products for the market in some regions, the Off Timer is set to automatically activate 4 hours after the product powers on. This is done in accordance with power supply regulations. If you do not want the timer to activate, go to → System → Off Timer Plus and set Off Timer to Off .
Configuring Eco Timer
Eco Timer : Turn on Eco Timer mode.
Eco Off After : The Eco Timer can be set between 10 and 180 minutes. The product will automatically power off after the specified time has elapsed.
―
This option is only available when Eco Timer is set to On .
33
PC/AV Mode
Set PC/AV Mode to AV . The picture size will be enlarged.
This option is useful when you view a movie.
• Set to PC when connected to a PC.
• Set to AV when connected to an AV device.
―
Supplied for the wide models only such as 16:9 or 16:10.
―
If the monitor (when set to HDMI , DisplayPort ) is in power saving mode or is displaying the message Check
Signal Cable , press the icon to display the On Screen Display (OSD). You can select PC or AV .
DisplayPort Ver.
Select your Displayport.
―
Incorrect settings may cause the screen to go blank. If this occurs, check the device specifications.
―
If the monitor (when set to HDMI , DisplayPort ) is in power saving mode or is displaying the message Check
Signal Cable , press the icon to display the On Screen Display (OSD). You can select 1.1
or 1.2↑ .
―
If you select 1.1
, the maximum resolution of your screen drops to 2560 x 1440 due to the limitations in HBR1 transmission speeds.
HDMI Mode
Select the HDMI mode to use.
―
The supportable device and resolution may differ depending on its version.
―
When the version is changed, the screen may blink.
―
If you set the HDMI Mode to 1.4
, some high resolutions may not be supported because of bandwidth
― limitation of the HDMI 1.4 protocol.
When the setting is not appropriate, a blank screen may appear. In this case, check the specifications of the
― device.
Set the HDMI Mode to 1.4
when there is no sound output from the DVD connected to our product.
―
Not available when PBP Mode is set to On .
―
If the monitor(when set to HDMI ) is in power saving mode or is displaying the message Check Signal Cable , press the icon to display the On Screen Display(OSD). You can select 1.4
or 2.0
.
Source Detection
Select either Auto or Manual as the method to recognize input signal.
―
Not available when PBP Mode is set to On .
Key Repeat Time
Control the response rate of a button when the button is pressed.
Acceleration , 1 sec , or 2 sec can be selected. If No Repeat is selected, a command responds only once when a button is pressed.
34
Power LED On
Configure the settings to enable or disable the power LED located at the lower part of the product.
• Working : The power LED is on when the product is turned on.
• Stand-by : The power LED is on when the product is turned off.
Reset All
Return all the settings for the product to the default factory settings.
Information
View the current input source, frequency and resolution.
Picture
PBP
OnScreen Display
System
Information
Information
LU********/**
S/N:**************
HDMI
**** x ****
**kHz **Hz
PBP
Picture
PBP
OnScreen Display
System
Information
Information
LU********/**
S/N:**************
HDMI
**** x ****
**kHz **Hz
DisplayPort
**** x ****
**kHz **Hz
Exit
Exit
―
The displayed image may differ depending on the model.
35
Chapter 08
Installing the Software
Easy Setting Box
Easy Setting Box enables users to use the monitor by partitioning multiple sections.
To install the latest version of Easy Setting Box , download it from the Samsung Electronics website at http://www.samsung.com.
―
The software may not work properly if you do not restart the computer after the installation.
―
The Easy Setting Box icon may not appear depending on the computer system and the product specifications.
―
If the shortcut icon does not appear, press the F5 key.
Restrictions and Problems with the Installation
The Easy Setting Box installation may be affected by the Graphics Card, Motherboard and the
Networking Environment.
System Requirements
OS
• Windows 7 32Bit/64Bit
• Windows 8 32Bit/64Bit
• Windows 8.1 32Bit/64Bit
• Windows 10 32Bit/64Bit
Hardware
• At least 32MB of memory
• At least 60MB of free space on the hard disk drive
36
Chapter 09
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Center
―
Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC, perform a self-diagnosis test.
1 Power off both the PC and product.
2 Disconnect the cables from the product.
3 Power on the product.
4 If the message Check Signal Cable appears, the product is working normally.
―
If the screen remains blank, check the PC system, video controller and cable.
Checking the Resolution and Frequency
For a mode that exceeds the supported resolution(refer to
Standard Signal Mode Table ), the message
Not Optimum Mode will appear for a short time.
―
The displayed resolution may vary, depending on the computer system settings and cables.
Check the following.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connectors are locked.
Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust the screen settings.)
Screen issue
The power LED is off. The screen will not switch on.
Check that the power cable is connected properly.
The message Check Signal Cable appears.
Check that the cable is properly connected to the product.
Check that the device connected to the product is powered on.
37
Not Optimum Mode is displayed.
This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product.
Change the maximum resolution and frequency to suit the product performance, referring to
Standard Signal Mode Table (
).
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Remove any accessories (video extension cable, etc.) and try again.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky. There are shadows or ghost images left on the screen.
Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product. Next, if required, change the settings, referring to Standard Signal
Mode Table (
) in this manual and the Information menu on the product.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast .
Screen color is inconsistent.
Change the Color settings.
The colors on the screen have a shadow and are distorted.
Change the Color settings.
White does not really look white.
Change the Color settings.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
The product is operating in power-saving mode.
Press any key on the keyboard or move the mouse to return to normal operating mode.
Text is blurry.
If using a Windows OS (e.g. Windows 7, Windows 8, Windows 8.1 or Windows 10): Go to Control Panel →
Fonts → Adjust ClearType text and change Turn on ClearType .
Video playback is choppy.
Playback of high-definition large video files can be choppy. This may be because the video player is not optimized for the computer resource.
Try playing the file on another video player.
Sound issue
There is no sound.
Check the connection of the audio cable or adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
Video is available but there is no sound.
Sound cannot be heard if a HDMI-DVI cable is used to connect the input device.
Connect the device using an HDMI cable or DP cable.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
38
Q & A
―
Refer to the user manual for your PC or graphics card for further instructions on adjustment.
How can I change the frequency?
Set the frequency on your graphics card.
• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor , and adjust Refresh rate under Monitor settings .
• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor , and adjust Refresh rate under Monitor settings .
• Windows 10: Go to Settings → System → Display → Advanced display settings → Display adapter properties → Monitor , and adjust Screen refresh rate under Monitor settings .
How can I change the resolution?
• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust Resolution , and adjust the resolution.
• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust Resolution , and adjust the resolution.
• Windows 10: Go to Settings → System → Display → Advanced display settings , and adjust the resolution.
How do I set power-saving mode?
• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
• Windows 8(Windows 8.1): Set power-saving mode in Settings → Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
• Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen timeout settings → Power & sleep or BIOS SETUP on the PC.
39
Chapter 10
Specifications
General
Model Name
Size
Display area
Pixel Pitch
Maximum Pixel Clock
Power Supply
Signal connectors
Environmental conditions
U32R590CW* / U32R591CW* / U32R592CW* / U32R594CW*
32 Class (31.5 Inches / 80.0 cm)
697.31 mm (H) x 392.23 mm (V)
0.181 mm (H) x 0.181 mm (V)
533.25 MHz (DisplayPort)
594.00 MHz (HDMI)
AC100-240V~ 50/60Hz
Based on the AC voltage of the adapter. For the DC voltage of the product, refer to the product label.
HDMI, DisplayPort
Operating
Temperature: 50 °F – 104 °F (10 °C – 40 °C)
Humidity: 10 % – 80 %, non-condensing
Storage
Temperature: -4 °F – 113 °F (-20 °C – 45 °C)
Humidity: 5 % – 95 %, non-condensing
―
Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes place automatically. However, you can customize the installation settings if desired.
―
Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the LCD panel. This does not affect product performance.
―
The above specifications are subject to change without notice to improve quality.
―
This device is a Class B digital apparatus.
―
For detailed device specifications, visit the Samsung Electronics website.
40
Standard Signal Mode Table
Model Name
Synchronization
Resolution
Horizontal Frequency
Vertical Frequency
Optimum Resolution
Maximum Resolution
U32R590CW* / U32R591CW* / U32R592CW* / U32R594CW*
30 – 135 kHz
56 – 75 Hz (DisplayPort)
24 – 75 Hz (HDMI)
3840 x 2160 @ 60 Hz (DisplayPort)
3840 x 2160 @ 60 Hz (HDMI)
3840 x 2160 @ 60 Hz (DisplayPort)
3840 x 2160 @ 60 Hz (HDMI)
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank even though the power LED turns on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
Displayport
Resolution
IBM, 720 x 400
VESA, 640 x 480
MAC, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
MAC, 832 x 624
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
MAC, 1152 x 870
VESA, 1280 x 720
Horizontal Frequency (kHz)
31.469
31.469
35.000
37.861
37.500
35.156
37.879
48.077
46.875
49.726
48.363
56.476
60.023
67.500
68.681
45.000
Vertical Frequency (Hz)
70.087
59.940
66.667
72.809
75.000
56.250
60.317
72.188
75.000
74.551
60.004
70.069
75.029
75.000
75.062
60.000
Pixel Clock (MHz)
28.322
25.175
30.240
31.500
31.500
36.000
40.000
50.000
49.500
57.284
65.000
75.000
78.750
108.000
100.000
74.250
Sync Polarity (H/V)
+/+
+/+
+/+
+/+
-/-
-/-
-/-
+/+
+/+
-/-
+/+
-/+
-/-
-/-
-/-
-/-
41
Displayport
Resolution
VESA, 1280 x 800
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1600 x 900
VESA, 1680 x 1050
VESA, 1920 x 1080
VESA, 2560 x 1440
VESA, 3840 x 2160
HDMI
Resolution
IBM, 720 x 400
VESA, 640 x 480
MAC, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
MAC, 832 x 624
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
MAC, 1152 x 870
VESA, 1280 x 720
VESA, 1280 x 800
VESA, 1280 x 1024
Horizontal Frequency (kHz)
49.702
63.981
79.976
55.935
60.000
65.290
67.500
88.787
133.313
Horizontal Frequency (kHz)
46.875
49.726
48.363
56.476
60.023
67.500
68.681
45.000
49.702
63.981
31.469
31.469
35.000
37.861
37.500
35.156
37.879
48.077
Vertical Frequency (Hz)
59.810
60.020
75.025
59.887
60.000
59.954
60.000
59.951
59.997
Vertical Frequency (Hz)
75.000
74.551
60.004
70.069
75.029
75.000
75.062
60.000
59.810
60.020
70.087
59.940
66.667
72.809
75.000
56.250
60.317
72.188
Pixel Clock (MHz)
83.500
108.000
135.000
106.500
108.000
146.250
148.500
241.500
533.250
Pixel Clock (MHz)
49.500
57.284
65.000
75.000
78.750
108.000
100.000
74.250
83.500
108.000
28.322
25.175
30.240
31.500
31.500
36.000
40.000
50.000
Sync Polarity (H/V)
-/+
+/+
+/+
-/+
+/+
-/+
+/+
+/-
+/-
Sync Polarity (H/V)
+/+
+/+
-/-
+/+
-/+
+/+
+/+
-/-
-/-
-/-
-/-
+/+
+/+
+/+
-/+
-/-
-/-
-/-
42
HDMI
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1600 x 900
VESA, 1680 x 1050
VESA, 1920 x 1080
VESA, 2560 x 1440
79.976
55.935
60.000
65.290
67.500
88.787
75.025
59.887
60.000
59.954
60.000
59.951
135.000
106.500
108.000
146.250
148.500
241.500
+/+
-/+
+/+
-/+
+/+
+/-
CEA, 3840 x 2160 67.500 30.000
297.000
+/+
CEA, 3840 x 2160 135.000
60.000
594.000
+/+
―
Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
―
Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
―
This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality.
To avoid this, it is recommended that you select the optimum resolution specified for your product.
―
Some resolutions listed in the table above may not be available depending on graphics card specifications.
43
Chapter 11
Appendix
Responsibility for the Pay Service (Cost to
Customers)
―
When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
• If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time.
• If a product is reinstalled to move to a different spot or to move to a different house.
• If customer requests instructions on how to use because of another company's product.
• If customer requests instructions on how to use the network or another company's Program.
• If customer requests software installation and setup for the product.
• If a service technician removes/cleans dusts or foreign materials inside of the product.
• If customer requests an installation additionally after purchasing a product through homeshopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
• External impact or drop.
• Use of supplies or separately sold product unspecified by Samsung.
• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
• Remodeling or repairing the product by customer.
• Using it with incorrect voltage or non-authorized electrical connections.
• Not following the "cautions" in User Manual.
Others
• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator,
Lamp, Filter, Ribbon, etc.)
―
If customer requests a service in case the product has no defect, service fee may be charged. So please read User Manual first.
44
advertisement
Key Features
- 81.3 cm (32") LCD TFT
- 4K Ultra HD 3840 x 2160 pixels 16:9
- 60 Hz 4 ms 250 cd/m² 2500:1
- Flicker-free technology
- 48 W
Related manuals
advertisement
Table of contents
- 4 Before Using the Product
- 4 Securing the Installation Space
- 4 Precautions for storage
- 4 Safety Precautions
- 5 Cleaning
- 5 Electricity and Safety
- 6 Installation
- 7 Operation
- 10 Preparations
- 10 Parts
- 10 Control Panel
- 11 Direct Key guide
- 12 Function Key Guide
- 14 Configuring Eye Saver Mode, Brightness and Contrast from the Initial Screen
- 14 Changing the Volume setting
- 15 Types of Ports
- 16 Adjusting the Product Tilt
- 16 Anti-theft Lock
- 17 Precautions for moving the monitor
- 18 Installation
- 18 Attaching the Stand
- 19 Removing the Stand
- 20 Connecting and Using a Source Device
- 20 Read below before installing the monitor.
- 20 Connecting and Using a PC
- 20 Connection Using the HDMI Cable
- 21 Connection Using the HDMI-DVI Cable
- 21 Connection Using the DP Cable
- 21 Connecting to Headphones
- 22 Connecting the Power
- 22 Tidying Up the Connected Cables
- 23 Correct posture to use the product
- 23 Driver Installation
- 23 Setting Optimum Resolution
- 24 Picture
- 24 SAMSUNG MAGIC Bright
- 25 Brightness
- 25 Contrast
- 25 Sharpness
- 25 Color
- 26 SAMSUNG MAGIC Upscale
- 26 HDMI Black Level
- 26 Eye Saver Mode
- 26 Game Mode
- 26 Response Time
- 27 Picture Size
- 27 Screen Adjustment
- 28 PBP
- 28 PBP Mode
- 29 Sound Source
- 29 Picture Size
- 29 Contrast
- 30 OnScreen Display
- 30 Transparency
- 30 Language
- 30 Display Time
- 31 System
- 31 Self Diagnosis
- 33 Smart ECO Saving+
- 33 Off Timer Plus
- 34 PC/AV Mode
- 34 DisplayPort Ver.
- 34 HDMI Mode
- 34 Source Detection
- 34 Key Repeat Time
- 35 Power LED On
- 35 Reset All
- 35 Information
- 36 Installing the Software
- 36 Easy Setting Box
- 36 Restrictions and Problems with the Installation
- 36 System Requirements
- 37 Troubleshooting Guide
- 37 Requirements Before Contacting Samsung Customer Service Centre
- 37 Testing the Product
- 37 Checking the Resolution and Frequency
- 37 Check the following.
- 39 Q & A
- 40 Specifications
- 40 General
- 41 Standard Signal Mode Table
- 44 Appendix
- 44 Responsibility for the Pay Service (Cost to Customers)
- 44 Not a product defect
- 44 A Product damage caused by customer's fault
- 44 Others