AKEEYO Car Dash Cam FHD 1080P Front and Rear Dash Camera 3 Inch IPS Screen 140° Wide Angle On-Dash Camera User Manual

AKEEYO
Front and Rear Camera
Car Drive Recorder
AKY-D2
User Manual
Catalog
@ Safety Information
@Product Overview 3
@Part Names 4
@ Micro SD Card 6
@Time and Date Setting 7
@installation 8
@ Movie Recording Mode 10
@Still Image Mode 11
@Video and Still Picture Playback Mode 12
@ Movie Recording Type 13
@Playback Recording Video 14
@Setting Menu 15
@Troubleshooting 18
@Specifications 19
Safety Information
Power supply
@Do not operate or handle the power cable with wet hands. Doing so may result in
electrocution.
eDo not use damaged power cables. Doing so may result in electrical fire or electrocution.
eKeep the power cable away from all heat sources. Failure to do so may cause the power
cord insulation to melt, resulting in electrical fire or electrocution.
eUse the power cable with the correct connector and make sure the power cable is
connected securely and is firmly in place. Failure to do so may result in electrical fire or
electrocution.
eDo not modify or cut the power cable. Also, do not place heavy objects on the power cable
or pull, insert, or bend the power cable using excessive force. Doing so may result in electrical
fire or electrocution.
®When connecting the power cable to the product, ensure that the connection between
the cable plug and the power cable connector on the product is secure. If the connection
is loose, the power cable may become disconnected due to vehicle vibration. Video recording
is not available if the power connector is disconnected.
Safety Information
Product management and operation
@Do not use chemical cleaners or solvents to clean the product. Doing so may damage plastic
components of the product. Clean the product using a clean, soft, and dry fabric
OUse the product at a temperature between 32° Fand 140° F (0° Cto 60° C).The product may not
fuction as designed and some permanent physical damages may result if it is operated or stored
out of the specified temperature ranges.Such damages are not covered by the warranty.
@Frequently check the product for the proper installation position. Impact caused by extreme
road conditions may alter the installation position. Ensure that the product is positioned as
instructed in this guide.
@Do not expose the product to direct sunlight or intense light. The lens or internal circuitry
may fail otherwise.
@®Do not disassemble the product or subject the product to impact. Doing so may damage
the product.Unauthorized disassembly of the product voids the product warranty.
Handle with care. If you drop, mishandle, or expose the product to external shocks,
it may cause damage and/or result in the malfunction of the product.
@ Avoid excessive humidity and do not allow any water to enter the product. Electronic
components inside the product may fail if exposed to humidity or water.
@Cleaning the lens regularly. Foreign matter on the lens will reduce the quality of the recording.
@If you do not use this product for a long time, it is recommended to unplug the power cable.
@This device is designed to record video while the vehicle is in operation. The quality of the
video might be affected by weather conditions and the road environment, such as whether it is
day or night, presence of street lighting, entering/exiting tunnels, and the surrounding temperature.
Product Overview
Ensure that the product is out of the reach of children and pets. If the product breaks, it may
result in fatal damage.
Hl Main Unit HB Rear camera
(With connection cable)
=Q
—1
EM Cigar jack
EM MicroSD memory card EM User Manual
<>
Xthe actual product may be different from the image of illustrated product.
Part Names
1 Memory Card Slot
2 Button (UP) / Switching Screen Display Mode
@ Setting menu screen: Move the button (UP) by short press.
@ Movie Mode / Still Image Mode: Short press switches the display mode of the front
and rear cameras.
XThe screen display modes of the front and rear cameras are switched in the
following order.
Е + В (wipe) > R+F (wipe) > F > R — R (left) + F (right)
F = front camera R = rear camera
rear front Ш
3 MENU / Return
@®When recording stopped: Press briefly to display each setting menu screen.
@Playback mode: Press and hold for about 3 second s to switch between the
front and rear camera files.
4 Button (DOWN) / Recording ON / OFF
@ Setting menu screen: Move the button (DOWN) by short press.
@®Video mode: A short press switches the audio recording ON / OFF.
4
Part names
10
11
12
13
14
15
16
17
RESET
OReset the machine settings and restart.
MIC
@Used for voice recording. X It doesn” t work when set to OFF.
OK (confirm)
@ Setting menu screen: Press and hold to confirm items or settings.
@Video mode: A short press will start / stop recording.
MODE
@Stop recording: Short press to switch between Movie / Still picture / Movie playback
/ Still picture playback mode.
SOS Lock
@During recording: À short press will start / stop emergency recording.
Power / Liquid Crystal ON/ OFF
@Hold power ON / OFF for 3 seconds
* This dash cam doesn” t have a built-in battery, it can” t be turned on
unless the power cable is connected.
O When the power is connected: Press briefly to switch the liquid crystal ON / OFF.
Speaker
Front Camera Lens
@® Records the front view.
Mini USB Power Port
OPlug power cable into the supplied cigarette lighter.
Mount Connecter
@Used to connect the mount.
Micro USB Rear Camera Power Cable Port
OUsed to connect the the rear camera.
Monitor Screen
Operation Indicator
Micro SD card
micro SD card insertion and removal
@Inserting the memory card
Ensure that the product is turned off, and then
gently push the bottom of the memory card with
your fingernail. The lower part of the memory card
will be exposed. Remove it from the product.
@Removing the memory card |
Ensure that the product is turned off, and then gently
push the bottom of the memory card with your fingernail.
The lower part of the memory card will be exposed.
Remove it from the product.
Compatible Micro SD Card
Olt supports micro SD card of 8 ~ 128GB (Class 10 and above).
However, it does not guarantee the operation of all micro SD cards.
O Cards of the UHS-I standard may not work even if they are interchangeable with Class 10.
@ Be careful when replacing the card as it does not support UHS-II and U3 standard cards.
@ The commercially available micro SD card may not be recognized depending on the manufacturer
and production lot.
Micro SD Card Format
It is recommended to format the card regularly. If you do not format the card regularly,
you may not be able to record correctly.
* Recommended once monthly.
Format with this unit
Power on — Press OK button to stop recording — Press MENU button 4 times, General setting
menu screen > [Format SD-Card] — OK button determined
Format on PC
Power off > Remove micro SD card from this unit > Connect micro SD card to computer >
Please operate the card format on the PC side.
Please Note:
ONote: Formatting the card will delete all the contents of the record. Please backup
necessary video filesin advance.
* Saved settings are not affected.
@ As micro SD card is a consumable item, it is recommended to replace it with a new one
periodically, even if you are using it normally,
If you use it for a long time, it may not be able to record normally and may occur error.
6
Time and Date Setting
This dash cam haven’ tthe function to synchronize the date and time automatically.
Set the date and time before using it, as it will display the date and time correctly in the recorded
video file.
1. Connect the power cable to this unit and turn on the power.
2. Press the OK button to stop recording.
3. Press the MENU button to display the setting menu.
Please refer to [P4 Part Names] for the position of the MENU button.
Video Clip Time
Rear Mirror
Ip) Audio Record
4. After pressing the MENU button three times again, the general settings menu will be displayed.
Move to [Time Setting] with the cursor button. When the OK button is pressed, the date
and time setting screen is displayed.
Ч К 0;
Keytone
AC 50 ||
OL ное в
iE
Date Format
Adjust the number with the cursor button, and determine the item set with the OK button.
After completing the settings, return to the general settings menu screen.
5. Press the MENU button to return to movie mode. Please check the date and time display
on the LCD screen.
A please note:
OThe date and time setting of this unit has an error of about 30 seconds per month, and
customers who have a requirement for time accuracy.Please adjust the date and time once
a month.
@ Since this unit haven’ t built-in battery, the set date and time can be stored for
about 2 to 3 weeks. Long time use.lf not used, please set the time.
7
Installation
@ Installing the front camera (main unit)
Follow the instructions to properly install the product.
Selecting an installation location
Select an installation location that can record the
entire view in front of the vehicle without obstructing
the driver’ s vision. Ensure that the front camera lens
is located in the center of the windshield.
(Connecting the power cable
When the engine and electrical accessories are turned off, connect the car charger.
The hardwiring cable (optional) must be professionally installed to the vehicle by a
trained mechanic.
Connect the car charger to the product” s DC-IN power
port (Mini USB power port) andinsert the cigar jack into the vehicle” s power
socket.
The location and specifications of the power socket may differ by vehicle make and model.
* Use the authentic car charger. Use of third party power cables may damage the product and
result in electrical fire or electrocution due to the voltage difference.
* Do not cut or modify the power cable yourself. Doing so may damage the product or the vehicle.
« For safe driving, arrange the cables to prevent the driver's vision from being obstructed or
interfering with driving.
Installing the rear camera
Refer to the following instructions to properly install the rear camera.
Selecting an installation location
Select a location on the rear windshield where there
is no defrost grid wire and the camera can record
the entire rear view.
Installation
* For vehicles with a sunshade attached to the rear windshield, you must select a location
where using the sunshade will not interfere with camera operation.
* The adhesive part of the rear camera should not touch the defrost grid.
Rear camera cable Cigarette power cable
La
Please open the car engine. turn the power on, dash cam will start recording automatically.
While checking the LCD screen, adjust the front and rear camera lens to the best angle.
Recording will stop automatically when the car engine is closed.
When the capacity of the microSD card is full, the latest video files will overwrite the oldest
video files (loop recording).Therefore, the latest video file is always saved.
Movie Recording Mode
e [CursorA] button
00:00:00 Switch back and forth camera display mode
1080FHD e [Cursor Y] button
Switch microphone on / off
e [OK] button
Start / stop recording
e BD] SOS lock button
Start / stop emergency recording
e El] setting button
Stop recording: Display the setting menu screen
2018/12/12 18:18:18 Oe ] mode button
Recording stopped: Recording / still image / video
Front camera screen
playback / still image Switch playback mode
The image of the front camera is displayed.
Wipe screen
The image of the rear camera is displayed.
* front and rear camera screen display mode is [front + rear (wipe)] or,
It is displayed only when it is set to [Rear + Front (wipe)].
Movie recording mode icon
Loop recording time icon
Display the loop time. It can be set to 1/2/3/5/10 minutes.
Exposure compensation icon
Microphone icon
Displays the audio recording status.
Record ON: Record OFF:
Emergency recording icon
Displays the status of emergency recording.
During emergency recording: O- Recording at all times: Hide
ERE Recording time
(UE Video resolution icon
Display the recording resolution.
= G sensor icon
“ The setting value of G sensor is displayed.
Off: Hide high: = in: = low: =
Card icon a
When installed a card: When the card is not installed:
18: 18: 18 Time display
The setting of date and time information will be displayed.
% Please refer to [P7 Time Setting] for setting method.
10
Still Image Mode
e [Cursor] button
4 Switch back and forth camera display mode
e [OK] button
5 Take a still picture
e [El] setting button
Stop recording: Display the setting menu screen
e ] mode button
Switch between recording / still picture
/ playback mode
1. Still image mode icon 6
2. Front camera screen
The image of the front camera is displayed.
3. Possible number of shots
Estimated number of shots to be taken calculated by the card remaining amount.
X Reference only, numbers displayed by card are different.
4. Still image resolution
5. Image quality icon
6. micro SD card icon
When installed a card: When the card is not installed:
7. ISO sensitivity icon
8. Wipe screen
The image of the rear camera is displayed.
X Front and rear camera screen display mode [front + rear (wipe)] or, [rear + front (wipe)]
It is displayed only when it is set to.
9. Exposure compensation icon
A Please Note:
OThe still image resolution is fixed at [Front: 1920 X 1080] and [Rear: 1920 X 1080].
11
Video and Still Picture Playback Mode
You can playback the recorded movie or still picture file on this unit.
[Video play list screen] [Video playback screen]
1 3 2
FLFE190101-000000-000000F 1/68
ww
| / /
vw ge
| / /
2019/01/01 00:00:00 [00:01:00] pb 06:00:13/00:01:00
4
e [Cursor // Y] button 1. Video playback mode icon
Movie playlist screen: select a file 2. filename
During video playback: Rewind / fast forward 3. number of pages
e [OK] button 4.Shooting date
Movie playlist screen: Play the selected file 2 Movie playbac hy
Video playback screen: Play / pause video 7. Video resolution
e [El ] setting button
Short press: Display the playback menu screen
Press and hold for about 3 seconds: Switch back and forth camera file
e M ] mode button
Video playlist screen: Switch the mode
Movie playback screen: Return to the previous screen
[Still picture playlist screen] [Still picture reproduction screen]
1 2 3 2
r= IMG190101-000000-000000F : :
1920*1080 5
a
/ |
. «ME
/ /
2019/01/01 00:00:00
4
e [Cursor// Y] button 1. Still image playback mode icon
Select a file 2. file name
e [OK] button
. 3. number of pages
Play the selected file
e El] Setting button 4. Shooting date .
Short press: Display the playback menu screen 5. Still image resolution
Press and hold for about 3 seconds: Switch back and forth camera file
© M] Mode button
Still picture playlist screen: Switch the mode
Still image playback screen: Return to the previous screen
Movie Recording Type
Loop recording (automatic overwrite video file)
It always records from engine start (ACC ON) to engine stop (ACC OFF).
Video is saved in units of 1 minute / 2 minutes / 3 minutes / 5 minutes / 10 minutes
depending on the setting.
When the card is full, files with the oldest date and time will be overwritten in order.
Emergency recording (video file will be overwritten)
X [Impact sensing recording]
During continuous recording, when the G sensor mounted on this unit detects an impact,
emergency recording starts automatically. Recorded video files are protected (locked).
X If G sensor sensitivity is set to off, shock can not be detected and shock detection recording
can not be started.
X [Manual emergency recording start]
During continuous recording, pressing the emergency recording button [ à activates
emergency recording.
While the emergency recording is recording, pressing the emergency recording ‚
utton again cancels the emergency recording and returns to the continuous recording.
* Video file recorded by shock detection recording and manual emergency recording is [Event]
of Micro SD card.
It is saved in a folder, and is automatically overwritten when the [Event] folder capacity is full.
About emergency recording save file
Recording® Recording Recording®
1 minute * 1 1 minute | Recording continued ...
An accident occurs in the loop of movie 2 and the G sensor detects impact and
emergency recording starts.Movie file 2 + previous movie file (Video 1) + next movie
file (3) [Event] folder. Will be saved to.
Л please note:
OA total of 6 movie files are saved to simultaneously save the movie files of the front and
back cameras.
O If the number of emergency video files increases, the card capacity may be full and
recording may not be possible.Format the micro SD card regularly.
O It is recommended to set the loop recording time to 1 minute.
13
Playback Recording Video
Playback on this device
Recorded files can be playback on this device.
X Please refer to [P12 video and still picture playback mode].
Playback on PC
[Connect this unit to PC]
After confirming that the engine is off, connect a commercially available mini USB cable to the
unit and PC.When the [USB function] screen is displayed on the LCD screen of this unit, select
the [MSDC] item and press the OK button.The recorded file is displayed on the PC's external
device.
PY [Connect micro SD card for recording to PC]
After confirming that the engine is off, remove the micro SD card for recording, and use a
commercially available card. Connect to a PC with a reader. The recorded file is displayed
on the PC's external device.
DATA
Event —» Emergency recording file: about 13% of the card capacity
Mormal—» Always-recorded file: about 73% of card capacity
Parking——» Parking surveillance recording file: about 13% of the card capacity
Photo—» still image: 1% of card capacity
IndexData.txt
F — Front camera
R —— Rear camera
14
Setting Menu
While recording is stopped, press the=lnit's setting button to display the setting menu screen
and make various settings.
Each time the setting button is pressed, [Recording mode], [Capture], [Playback setting],
and [Setting] are displayed.
[Movie Mode] [Photo Mode]
E E 4,
Video Resolution
Video Clip Time
IE Rear Mirror
Audio Record
[General Settings]
» o bo, General Settings
Keytone
I Delete Auto Power Off
= Protect Time Setting
vedio Type Date Format
=
Video Resolution
Set the front camera video resolution.
FHD 30 fps / HD 30fps
* The rear camera is fixed to FHD 25 fps.
Video Clip Time
You can select the loop recording time that is recorded as 1/2/3/5/10 minutes.
Rear Mirror
Selects the mirror image of the rear camera on / off.
X On: Rear camera shows mirror image / Off: Rear camera shows regular image
Audio Record
Select On / Off of audio recording during recording.
15
Setting Menu
Still image size
Display the still image shooting resolution of the front camera.
2 M:1920 x 1080
1.2 M: 1280 x 960
Rear camera is fixed at 1920 X 1080.
Playback Setting
Vollume
Set the volume.
Set the volume of playback video file and button operation sound.
* When set to 0, there is no sound when playing back a movie on this unit and operating the
buttons on this unit.
Delete
Delete the file on this unit.
Delete One/ Delete All
Protect
Protect (lock) the file.
Protect One: Protect one file.
Unprotect One: Unprotect one file.
Protect All: Protect all files.
Unprotect All: Unprotect all files.
Video Type
Select the type of movie file displayed on the movie playback mode screen.
Normal: Always show files taken by recording
Parking: Display files taken in parking monitoring mode
Emergency: Display files taken by emergency recording
General Settings
Keytone
Select On / Off of the console operation sound.
Auto Power Off
While recording is stopped, if there is no operation for the set time [Never / 1 min /
5 mins], the power will be turned off automatically.
X If set to [Never], the power is on all the time.
Time Setting
Set the date and time.
Date Format
Set the date and time display format.
Stamp
Set whether to record the shooting date and time in the video file.
* Even when set to [Off], the date and time will be displayed on the shooting screen.
16
Setting Menu
Language
Set the display language.
Flicker
We prevent flicker such as LED signal light at the time of photography.
Screen Timeout
Select the setting time of the screen saver from [Off / 1 min / 3 mins].
Protect Level
Sets the sensitivity at which shock detection animation operates.
x When set to [Off], G sensor won” t work.
Motion Detection
Set the sensitivity at which motion detection animation operates.
X If set to [Off], motion detection recording couldn” t be used.
Setup Reset
Initializes all settings of this unit.
Format SD-Card
All data will be deletec, if you format card, please back up necessary files in advance.
FW Version
Displays the version of this unit's software.
17
Troubleshooting
If a problem occurs during using, please try the following items.
Otherwise,please contact the support center immediately.
Email:
Problems
Solution
Cannot power on
the product
@ Make sure the power cable (the car charger or the hardwiring
cable) is connected to the vehicle and the product properly.
OCheck the vehicle” s battery level.
Freeze, operation error
OPress the reset button to reset the machine.
The memory card
cannot be recognized.
OEnsure that the memory card has been inserted in the correct
direction. Before inserting the memory card, ensure that the
metal contacts on the memory card are facing toward the lens
of the product.
@Turn off the power, remove the memory card, and then check
to ensure that the contacts in the memory card slot are not
damaged.
@Ensure that the memory card is an authentic product
distributed by LANCERTECH. LANCERTECH does not guarantee
compatibility and normaloperation of third-party memory
cards.
The voice guide and
/or buzzer do not
sound
@Check if the volume is set to the minimum. For more
information about how to adjust the volume, refer to P16
"Playback Setting— Volume" adjusting the system volume.
Rear camera display
error
@ Make sure that the rear camera connection is set correctly.
@ Make sure that the camera connection cable is not broken.
@Please try to restart.
Always recording
error
@ Make sure there is enough card memory.
@Switch to recording mode and try pressing the OK button.
The recorded video
cannot be played
onaPC
@Copy the video file to a PC and then play it.
@Please update the Windows Media Player to latest version
on PC of Windows 7 / 8.1 / 10 before playing.
@We can not guarantee that all PCs can playback video file.
18
Model
AKY-D2
Product Name
Car Dash Cam
Micro SD Micro SD 8~128G(3 Class 10 or Higher)
2 million pixels CMOS Sensor
Front Camera
Angle of View: 140° 1920 X 1080@30fps
SONY IMX323 2 million pixels CMOS Sensor
Rear Camera
Angle of View: 140° 1920 Х 1080@25fps
Movie file Configuration
1min/2mins/3mins/5mins/10mins
Image Segmentation
Display
Front Camera+Rear Camera(Simultaneously)
/Rear Camera+Front Camera(Simultaneously)
/Front Camera/Rear Camera/Rear Camera
(Left)+Front Camera(Right)
G Sensor
3-axis acceleration sensor (3D, £3G), 5 levels
Recording Mic
Internal * Set to ON/OFF
Speaker
1W/80X1
Recording Solution
Loop Recording / Collision Lock / Remote Control Lock
Video and Photo File Format
Video: H.264.(mov) Photo:jpeg
Video Playback
Windows Media Player
Power Input
DC 12 / 24 V Supported
Working environment
temperature
32° Fand140° F(0° Cto60° C) XSafe Using Temperature
* Specifications are subject to change without notice for product improvement.
X If you buy consumables, please contact the support center.
19