- Vehicles & accessories
- Motor vehicle accessories & components
- Dashcam
- AKEEYO
- Car Dash Cam FHD 1080P Front and Rear Dash Camera 3 Inch IPS Screen 140° Wide Angle
- User manual
AKEEYO Car Dash Cam FHD 1080P Front and Rear Dash Camera 3 Inch IPS Screen 140° Wide Angle On-Dash Camera User Manual
Add to my manuals
21 Pages
advertisement
▼
Scroll to page 2
of 21
AKEEYO Front and Rear Camera Car Drive Recorder AKY-D2 User Manual Catalog @ Safety Information @Product Overview 3 @Part Names 4 @ Micro SD Card 6 @Time and Date Setting 7 @installation 8 @ Movie Recording Mode 10 @Still Image Mode 11 @Video and Still Picture Playback Mode 12 @ Movie Recording Type 13 @Playback Recording Video 14 @Setting Menu 15 @Troubleshooting 18 @Specifications 19 Safety Information Power supply @Do not operate or handle the power cable with wet hands. Doing so may result in electrocution. eDo not use damaged power cables. Doing so may result in electrical fire or electrocution. eKeep the power cable away from all heat sources. Failure to do so may cause the power cord insulation to melt, resulting in electrical fire or electrocution. eUse the power cable with the correct connector and make sure the power cable is connected securely and is firmly in place. Failure to do so may result in electrical fire or electrocution. eDo not modify or cut the power cable. Also, do not place heavy objects on the power cable or pull, insert, or bend the power cable using excessive force. Doing so may result in electrical fire or electrocution. ®When connecting the power cable to the product, ensure that the connection between the cable plug and the power cable connector on the product is secure. If the connection is loose, the power cable may become disconnected due to vehicle vibration. Video recording is not available if the power connector is disconnected. Safety Information Product management and operation @Do not use chemical cleaners or solvents to clean the product. Doing so may damage plastic components of the product. Clean the product using a clean, soft, and dry fabric OUse the product at a temperature between 32° Fand 140° F (0° Cto 60° C).The product may not fuction as designed and some permanent physical damages may result if it is operated or stored out of the specified temperature ranges.Such damages are not covered by the warranty. @Frequently check the product for the proper installation position. Impact caused by extreme road conditions may alter the installation position. Ensure that the product is positioned as instructed in this guide. @Do not expose the product to direct sunlight or intense light. The lens or internal circuitry may fail otherwise. @®Do not disassemble the product or subject the product to impact. Doing so may damage the product.Unauthorized disassembly of the product voids the product warranty. Handle with care. If you drop, mishandle, or expose the product to external shocks, it may cause damage and/or result in the malfunction of the product. @ Avoid excessive humidity and do not allow any water to enter the product. Electronic components inside the product may fail if exposed to humidity or water. @Cleaning the lens regularly. Foreign matter on the lens will reduce the quality of the recording. @If you do not use this product for a long time, it is recommended to unplug the power cable. @This device is designed to record video while the vehicle is in operation. The quality of the video might be affected by weather conditions and the road environment, such as whether it is day or night, presence of street lighting, entering/exiting tunnels, and the surrounding temperature. Product Overview Ensure that the product is out of the reach of children and pets. If the product breaks, it may result in fatal damage. Hl Main Unit HB Rear camera (With connection cable) =Q —1 EM Cigar jack EM MicroSD memory card EM User Manual <> Xthe actual product may be different from the image of illustrated product. Part Names 1 Memory Card Slot 2 Button (UP) / Switching Screen Display Mode @ Setting menu screen: Move the button (UP) by short press. @ Movie Mode / Still Image Mode: Short press switches the display mode of the front and rear cameras. XThe screen display modes of the front and rear cameras are switched in the following order. Е + В (wipe) > R+F (wipe) > F > R — R (left) + F (right) F = front camera R = rear camera rear front Ш 3 MENU / Return @®When recording stopped: Press briefly to display each setting menu screen. @Playback mode: Press and hold for about 3 second s to switch between the front and rear camera files. 4 Button (DOWN) / Recording ON / OFF @ Setting menu screen: Move the button (DOWN) by short press. @®Video mode: A short press switches the audio recording ON / OFF. 4 Part names 10 11 12 13 14 15 16 17 RESET OReset the machine settings and restart. MIC @Used for voice recording. X It doesn” t work when set to OFF. OK (confirm) @ Setting menu screen: Press and hold to confirm items or settings. @Video mode: A short press will start / stop recording. MODE @Stop recording: Short press to switch between Movie / Still picture / Movie playback / Still picture playback mode. SOS Lock @During recording: À short press will start / stop emergency recording. Power / Liquid Crystal ON/ OFF @Hold power ON / OFF for 3 seconds * This dash cam doesn” t have a built-in battery, it can” t be turned on unless the power cable is connected. O When the power is connected: Press briefly to switch the liquid crystal ON / OFF. Speaker Front Camera Lens @® Records the front view. Mini USB Power Port OPlug power cable into the supplied cigarette lighter. Mount Connecter @Used to connect the mount. Micro USB Rear Camera Power Cable Port OUsed to connect the the rear camera. Monitor Screen Operation Indicator Micro SD card micro SD card insertion and removal @Inserting the memory card Ensure that the product is turned off, and then gently push the bottom of the memory card with your fingernail. The lower part of the memory card will be exposed. Remove it from the product. @Removing the memory card | Ensure that the product is turned off, and then gently push the bottom of the memory card with your fingernail. The lower part of the memory card will be exposed. Remove it from the product. Compatible Micro SD Card Olt supports micro SD card of 8 ~ 128GB (Class 10 and above). However, it does not guarantee the operation of all micro SD cards. O Cards of the UHS-I standard may not work even if they are interchangeable with Class 10. @ Be careful when replacing the card as it does not support UHS-II and U3 standard cards. @ The commercially available micro SD card may not be recognized depending on the manufacturer and production lot. Micro SD Card Format It is recommended to format the card regularly. If you do not format the card regularly, you may not be able to record correctly. * Recommended once monthly. Format with this unit Power on — Press OK button to stop recording — Press MENU button 4 times, General setting menu screen > [Format SD-Card] — OK button determined Format on PC Power off > Remove micro SD card from this unit > Connect micro SD card to computer > Please operate the card format on the PC side. Please Note: ONote: Formatting the card will delete all the contents of the record. Please backup necessary video filesin advance. * Saved settings are not affected. @ As micro SD card is a consumable item, it is recommended to replace it with a new one periodically, even if you are using it normally, If you use it for a long time, it may not be able to record normally and may occur error. 6 Time and Date Setting This dash cam haven’ tthe function to synchronize the date and time automatically. Set the date and time before using it, as it will display the date and time correctly in the recorded video file. 1. Connect the power cable to this unit and turn on the power. 2. Press the OK button to stop recording. 3. Press the MENU button to display the setting menu. Please refer to [P4 Part Names] for the position of the MENU button. Video Clip Time Rear Mirror Ip) Audio Record 4. After pressing the MENU button three times again, the general settings menu will be displayed. Move to [Time Setting] with the cursor button. When the OK button is pressed, the date and time setting screen is displayed. Ч К 0; Keytone AC 50 || OL ное в iE Date Format Adjust the number with the cursor button, and determine the item set with the OK button. After completing the settings, return to the general settings menu screen. 5. Press the MENU button to return to movie mode. Please check the date and time display on the LCD screen. A please note: OThe date and time setting of this unit has an error of about 30 seconds per month, and customers who have a requirement for time accuracy.Please adjust the date and time once a month. @ Since this unit haven’ t built-in battery, the set date and time can be stored for about 2 to 3 weeks. Long time use.lf not used, please set the time. 7 Installation @ Installing the front camera (main unit) Follow the instructions to properly install the product. Selecting an installation location Select an installation location that can record the entire view in front of the vehicle without obstructing the driver’ s vision. Ensure that the front camera lens is located in the center of the windshield. (Connecting the power cable When the engine and electrical accessories are turned off, connect the car charger. The hardwiring cable (optional) must be professionally installed to the vehicle by a trained mechanic. Connect the car charger to the product” s DC-IN power port (Mini USB power port) andinsert the cigar jack into the vehicle” s power socket. The location and specifications of the power socket may differ by vehicle make and model. * Use the authentic car charger. Use of third party power cables may damage the product and result in electrical fire or electrocution due to the voltage difference. * Do not cut or modify the power cable yourself. Doing so may damage the product or the vehicle. « For safe driving, arrange the cables to prevent the driver's vision from being obstructed or interfering with driving. Installing the rear camera Refer to the following instructions to properly install the rear camera. Selecting an installation location Select a location on the rear windshield where there is no defrost grid wire and the camera can record the entire rear view. Installation * For vehicles with a sunshade attached to the rear windshield, you must select a location where using the sunshade will not interfere with camera operation. * The adhesive part of the rear camera should not touch the defrost grid. Rear camera cable Cigarette power cable La Please open the car engine. turn the power on, dash cam will start recording automatically. While checking the LCD screen, adjust the front and rear camera lens to the best angle. Recording will stop automatically when the car engine is closed. When the capacity of the microSD card is full, the latest video files will overwrite the oldest video files (loop recording).Therefore, the latest video file is always saved. Movie Recording Mode e [CursorA] button 00:00:00 Switch back and forth camera display mode 1080FHD e [Cursor Y] button Switch microphone on / off e [OK] button Start / stop recording e BD] SOS lock button Start / stop emergency recording e El] setting button Stop recording: Display the setting menu screen 2018/12/12 18:18:18 Oe ] mode button Recording stopped: Recording / still image / video Front camera screen playback / still image Switch playback mode The image of the front camera is displayed. Wipe screen The image of the rear camera is displayed. * front and rear camera screen display mode is [front + rear (wipe)] or, It is displayed only when it is set to [Rear + Front (wipe)]. Movie recording mode icon Loop recording time icon Display the loop time. It can be set to 1/2/3/5/10 minutes. Exposure compensation icon Microphone icon Displays the audio recording status. Record ON: Record OFF: Emergency recording icon Displays the status of emergency recording. During emergency recording: O- Recording at all times: Hide ERE Recording time (UE Video resolution icon Display the recording resolution. = G sensor icon “ The setting value of G sensor is displayed. Off: Hide high: = in: = low: = Card icon a When installed a card: When the card is not installed: 18: 18: 18 Time display The setting of date and time information will be displayed. % Please refer to [P7 Time Setting] for setting method. 10 Still Image Mode e [Cursor] button 4 Switch back and forth camera display mode e [OK] button 5 Take a still picture e [El] setting button Stop recording: Display the setting menu screen e ] mode button Switch between recording / still picture / playback mode 1. Still image mode icon 6 2. Front camera screen The image of the front camera is displayed. 3. Possible number of shots Estimated number of shots to be taken calculated by the card remaining amount. X Reference only, numbers displayed by card are different. 4. Still image resolution 5. Image quality icon 6. micro SD card icon When installed a card: When the card is not installed: 7. ISO sensitivity icon 8. Wipe screen The image of the rear camera is displayed. X Front and rear camera screen display mode [front + rear (wipe)] or, [rear + front (wipe)] It is displayed only when it is set to. 9. Exposure compensation icon A Please Note: OThe still image resolution is fixed at [Front: 1920 X 1080] and [Rear: 1920 X 1080]. 11 Video and Still Picture Playback Mode You can playback the recorded movie or still picture file on this unit. [Video play list screen] [Video playback screen] 1 3 2 FLFE190101-000000-000000F 1/68 ww | / / vw ge | / / 2019/01/01 00:00:00 [00:01:00] pb 06:00:13/00:01:00 4 e [Cursor // Y] button 1. Video playback mode icon Movie playlist screen: select a file 2. filename During video playback: Rewind / fast forward 3. number of pages e [OK] button 4.Shooting date Movie playlist screen: Play the selected file 2 Movie playbac hy Video playback screen: Play / pause video 7. Video resolution e [El ] setting button Short press: Display the playback menu screen Press and hold for about 3 seconds: Switch back and forth camera file e M ] mode button Video playlist screen: Switch the mode Movie playback screen: Return to the previous screen [Still picture playlist screen] [Still picture reproduction screen] 1 2 3 2 r= IMG190101-000000-000000F : : 1920*1080 5 a / | . «ME / / 2019/01/01 00:00:00 4 e [Cursor// Y] button 1. Still image playback mode icon Select a file 2. file name e [OK] button . 3. number of pages Play the selected file e El] Setting button 4. Shooting date . Short press: Display the playback menu screen 5. Still image resolution Press and hold for about 3 seconds: Switch back and forth camera file © M] Mode button Still picture playlist screen: Switch the mode Still image playback screen: Return to the previous screen Movie Recording Type Loop recording (automatic overwrite video file) It always records from engine start (ACC ON) to engine stop (ACC OFF). Video is saved in units of 1 minute / 2 minutes / 3 minutes / 5 minutes / 10 minutes depending on the setting. When the card is full, files with the oldest date and time will be overwritten in order. Emergency recording (video file will be overwritten) X [Impact sensing recording] During continuous recording, when the G sensor mounted on this unit detects an impact, emergency recording starts automatically. Recorded video files are protected (locked). X If G sensor sensitivity is set to off, shock can not be detected and shock detection recording can not be started. X [Manual emergency recording start] During continuous recording, pressing the emergency recording button [ à activates emergency recording. While the emergency recording is recording, pressing the emergency recording ‚ utton again cancels the emergency recording and returns to the continuous recording. * Video file recorded by shock detection recording and manual emergency recording is [Event] of Micro SD card. It is saved in a folder, and is automatically overwritten when the [Event] folder capacity is full. About emergency recording save file Recording® Recording Recording® 1 minute * 1 1 minute | Recording continued ... An accident occurs in the loop of movie 2 and the G sensor detects impact and emergency recording starts.Movie file 2 + previous movie file (Video 1) + next movie file (3) [Event] folder. Will be saved to. Л please note: OA total of 6 movie files are saved to simultaneously save the movie files of the front and back cameras. O If the number of emergency video files increases, the card capacity may be full and recording may not be possible.Format the micro SD card regularly. O It is recommended to set the loop recording time to 1 minute. 13 Playback Recording Video Playback on this device Recorded files can be playback on this device. X Please refer to [P12 video and still picture playback mode]. Playback on PC [Connect this unit to PC] After confirming that the engine is off, connect a commercially available mini USB cable to the unit and PC.When the [USB function] screen is displayed on the LCD screen of this unit, select the [MSDC] item and press the OK button.The recorded file is displayed on the PC's external device. PY [Connect micro SD card for recording to PC] After confirming that the engine is off, remove the micro SD card for recording, and use a commercially available card. Connect to a PC with a reader. The recorded file is displayed on the PC's external device. DATA Event —» Emergency recording file: about 13% of the card capacity Mormal—» Always-recorded file: about 73% of card capacity Parking——» Parking surveillance recording file: about 13% of the card capacity Photo—» still image: 1% of card capacity IndexData.txt F — Front camera R —— Rear camera 14 Setting Menu While recording is stopped, press the=lnit's setting button to display the setting menu screen and make various settings. Each time the setting button is pressed, [Recording mode], [Capture], [Playback setting], and [Setting] are displayed. [Movie Mode] [Photo Mode] E E 4, Video Resolution Video Clip Time IE Rear Mirror Audio Record [General Settings] » o bo, General Settings Keytone I Delete Auto Power Off = Protect Time Setting vedio Type Date Format = Video Resolution Set the front camera video resolution. FHD 30 fps / HD 30fps * The rear camera is fixed to FHD 25 fps. Video Clip Time You can select the loop recording time that is recorded as 1/2/3/5/10 minutes. Rear Mirror Selects the mirror image of the rear camera on / off. X On: Rear camera shows mirror image / Off: Rear camera shows regular image Audio Record Select On / Off of audio recording during recording. 15 Setting Menu Still image size Display the still image shooting resolution of the front camera. 2 M:1920 x 1080 1.2 M: 1280 x 960 Rear camera is fixed at 1920 X 1080. Playback Setting Vollume Set the volume. Set the volume of playback video file and button operation sound. * When set to 0, there is no sound when playing back a movie on this unit and operating the buttons on this unit. Delete Delete the file on this unit. Delete One/ Delete All Protect Protect (lock) the file. Protect One: Protect one file. Unprotect One: Unprotect one file. Protect All: Protect all files. Unprotect All: Unprotect all files. Video Type Select the type of movie file displayed on the movie playback mode screen. Normal: Always show files taken by recording Parking: Display files taken in parking monitoring mode Emergency: Display files taken by emergency recording General Settings Keytone Select On / Off of the console operation sound. Auto Power Off While recording is stopped, if there is no operation for the set time [Never / 1 min / 5 mins], the power will be turned off automatically. X If set to [Never], the power is on all the time. Time Setting Set the date and time. Date Format Set the date and time display format. Stamp Set whether to record the shooting date and time in the video file. * Even when set to [Off], the date and time will be displayed on the shooting screen. 16 Setting Menu Language Set the display language. Flicker We prevent flicker such as LED signal light at the time of photography. Screen Timeout Select the setting time of the screen saver from [Off / 1 min / 3 mins]. Protect Level Sets the sensitivity at which shock detection animation operates. x When set to [Off], G sensor won” t work. Motion Detection Set the sensitivity at which motion detection animation operates. X If set to [Off], motion detection recording couldn” t be used. Setup Reset Initializes all settings of this unit. Format SD-Card All data will be deletec, if you format card, please back up necessary files in advance. FW Version Displays the version of this unit's software. 17 Troubleshooting If a problem occurs during using, please try the following items. Otherwise,please contact the support center immediately. Email: Problems Solution Cannot power on the product @ Make sure the power cable (the car charger or the hardwiring cable) is connected to the vehicle and the product properly. OCheck the vehicle” s battery level. Freeze, operation error OPress the reset button to reset the machine. The memory card cannot be recognized. OEnsure that the memory card has been inserted in the correct direction. Before inserting the memory card, ensure that the metal contacts on the memory card are facing toward the lens of the product. @Turn off the power, remove the memory card, and then check to ensure that the contacts in the memory card slot are not damaged. @Ensure that the memory card is an authentic product distributed by LANCERTECH. LANCERTECH does not guarantee compatibility and normaloperation of third-party memory cards. The voice guide and /or buzzer do not sound @Check if the volume is set to the minimum. For more information about how to adjust the volume, refer to P16 "Playback Setting— Volume" adjusting the system volume. Rear camera display error @ Make sure that the rear camera connection is set correctly. @ Make sure that the camera connection cable is not broken. @Please try to restart. Always recording error @ Make sure there is enough card memory. @Switch to recording mode and try pressing the OK button. The recorded video cannot be played onaPC @Copy the video file to a PC and then play it. @Please update the Windows Media Player to latest version on PC of Windows 7 / 8.1 / 10 before playing. @We can not guarantee that all PCs can playback video file. 18 Model AKY-D2 Product Name Car Dash Cam Micro SD Micro SD 8~128G(3 Class 10 or Higher) 2 million pixels CMOS Sensor Front Camera Angle of View: 140° 1920 X 1080@30fps SONY IMX323 2 million pixels CMOS Sensor Rear Camera Angle of View: 140° 1920 Х 1080@25fps Movie file Configuration 1min/2mins/3mins/5mins/10mins Image Segmentation Display Front Camera+Rear Camera(Simultaneously) /Rear Camera+Front Camera(Simultaneously) /Front Camera/Rear Camera/Rear Camera (Left)+Front Camera(Right) G Sensor 3-axis acceleration sensor (3D, £3G), 5 levels Recording Mic Internal * Set to ON/OFF Speaker 1W/80X1 Recording Solution Loop Recording / Collision Lock / Remote Control Lock Video and Photo File Format Video: H.264.(mov) Photo:jpeg Video Playback Windows Media Player Power Input DC 12 / 24 V Supported Working environment temperature 32° Fand140° F(0° Cto60° C) XSafe Using Temperature * Specifications are subject to change without notice for product improvement. X If you buy consumables, please contact the support center. 19
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project