Samsung NA36R5310FG 36-in 5 Burners Black Stainless Steel Gas Cooktop Installation Guide

 Gas Cooktop
Installation manual
NA3OS310F" / NA36"S310F"
WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property damage,
personal injury or death.
«DO NOT store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
« WHAT TO DO IF YOU SMELL GAS:
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch.
-DO NOT use any phone in your building.
Follow the gas supplier's instructions.
- If you cannot reach your gas supplier, call the fire
department.
« Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
- Immediately call your gas supplier from a neighbor's phone.
2 English
Contents
Before you begin 3
Important safety information 3
Gas cooktop components 8
What's in the box
Installation requirements 10
Pre-installation checklist 10
Location requirements 10
Gas suppiy requirements 12
Special gas requirements (gas models sold in Massachusetts] 13
Electrical requirements 13
Installation instructions 14
Installing your gas cooktop 14
Step 1. Unpack the cooktop 14
Step =. Installing the cooktop 14
step 3. Connect the cooktop to gas supply 15
Step 4. Check for gas leaxs 16
step 5, Electrical connections 17
Step 6. Assemble the cooktop burners 17
Step 7. Check the ignition of cooktop burners 19
step 8. Checking the flame quality 19
Step 9. Install the grates 20
Step-10. Final installation checklist 22
LP (Propane) conversion instruction 22
Supplied parts 23
Canverting the pressure regulator 24
Converting the cooktop burners 25
adjusting fow flame setting on cooktop burners 26
Bimal ASCH AN DFT AA DRE ih De Ad 2
wD SEC FA
Before you begin
About this manual
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
Important note to the installer
« Read all instructions contained in these instaliation instructions before installing
the cooktap.
« Remave all packing materials from the cooktop compartments before connecting
the electric and gas supply to the cooktop
Observe all governing codes and ordinances.
Be sure to leave these Instructions with the consumer,
Installation of this appliance requires basic mechanical skills,
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the Warranty.
Important note to the consumer
Keep these instructions with your user manual for future reference,
« As when using any appliance generating heat, there are certain safety
precautions vou should follow,
« Be sure your cooktop is installed and grounded properly by a gualified installer
pr service technician
« Make sure the wall coverings around the cooktop can withstand the heat
generated by the cooktop
« Cabinet storage space above the cooktop burners should be a minimum of 30 in
(762 cm}
Important note to the servicer
The electrical diagram is attached inside the burner box
Important safety information
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
a All electrical and gas equipment with moving parts can be dangerous. Please
read the important safety Instructions for this appliance in this manual. The
instructions must be followed to minimize the risk of injury, death, or property
damage.
« Save this manual. Please Do Not Discard
Symbols used in this manual
dk WARNING
Hazards or unsafe practices that may result in severe personal injury or death:
A CAUTION
Hazards or unsafe practices that may result in electric shock, personal injury, or
property damage:
(E) NOTE
Useful tips and (nsiructions,
These warning icons and symbols are here to prevent injury to you and others.
Please follow them explicitly. After reading this section, Keep it in a safe place far
future reference,
m
1
ds
=
=
io
ñ
Li
=
и
English 3
и
Bimal WASH ANDRA Dhol ih De EA 5 a CUE RA
-
=
=
Le
=
|
fu
—
=D.
E
À
1.
da
Le
=
=
=
=
ral)
—
=
=
Important safety information
California Proposition 65 Warning
A WARNING
Cancer and Reproductive Harm - www P65W amings.ca gov
Commonwealth of Massachusetts
« This product must be installed by a licensed plumber or gas fitter gualified ar
licensed by the State of Massachusetts. When using bBall-type gas shut-off vaives,
vou must use thé T-handie type: Multiple flexible gas lines must not be connected
In series:
General safety
A WARNING
To reduce the risk-of fire. electric shock, personal injuries, and/or death, obey the
following precautions.
« Do not touch any part of the cooktop, including
but not limited to, cooktop burners, during Or
immediately after cooking
« Know the location of the gas shut-off valve and
how to shut it off,
« Make sure the hold down brackets are properly installed on the cooktop. See the
installation instructions for more information,
« Do not let children near, in, or on the cooktop. Da not let children play with the
cooktop or any part(s) of the cogktop. Bo not leave children unattended in an
area where the cooktop is in use
+ Remove all packaging materials from the cooktop before operating to prevent
ignition of these materials. Keep all packaging materials out of children's reach:
Properly dispose the packaging materials after the copkiop is unpacked
« Do not store any object of interest to children on the cooktop or backguard of
the cooktop. Children climbing on the cooktop to reach items could be Killed ar
seriously injured
4 English
« Do not operate the cookiop if the cooktop or any part of the cooktop is damaged,
malfunctioning, or missing parts,
» Do not use the cooktop as a space heater. This cooktop is to be used far cooking
purposes anly
« Use only dry pot holders.
« Do not use the cooktop to heat unopened food containers.
« Unplug or disconnect power before servicing.
Fire safety
dk WARNING
To reduce the risk of fire, electric shock, pérsonal injuries, and/or death, obéy the
following precautions
« Do not store, place, or use flammable ar
combustible materials such as paper, plastic,
pot halders, linens, curtains, gasoline or other
flammable vapars or liquids near the cooktop.
« Do not wear loose fitting aor hanging garments
while using the cooktop.
« To avoid grease buildup, regularly clean the venis.
« Do not let pot holders or other flammable materials touch a heating element. Do
not use a towel or other bulky cloths in place of a pot holder.
* Во not use water on a grease fire. To put out a grease fire, turn off the heat
source and smother the fire with a tight-fitting id or use a multipurpose dry
chemical or foam-type fire extinguisher,
= Do not heat unopened food containers - buildup of pressure may cause container
to burst and result in injury
Bima ll WASH ANF AA Dhol ih De AL rc à
ACE A a
Gas safety
dà WARNING
To reduce the risk of fire, electric shock, personal injuries. and/or death, obey the
following precautions.
If you smell gas:
« Close the valve and do not use the cookitop.
« Do not light a match, candle, or cigarette
« Do not turn on any gas ar electric appliances.
F + Do nottouch any ciectrical sivitches or plug à
power cord into an outlet
2, « Do not use any phone in your bullding.
ra « Evacuate the room, building, or area of all
occupanís:
Ko « Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
» |f wou cannot reach your gas supplier, call the
fire department.
Checking for gas leaks
a Leak testing of the appliance shall be conducted according to the manufacturers
Instructions. Do not use a flame to check for gas leaks. Use a brush to spread a
soapy water mixture around the area You are checking. If there Isa gas leak, you
will see small bubbles in the soapy water mixture at the leak point.
Electrical and grounding safety
dk WARNING
To reduce the risk of fire, electric shock, personal Injuries, and/or death, obey the
following precautions
a Plug into a grounded 3-prang outlet
« Do not remove the ground prono.
« Do not use an adapter or an extension cord
« Do not use a damaged power plug, power cord,
Dr (o0se power outiet
« Do not modify the power plug, power cord, or
power outiet in any way
—
——
=
—
ul
—
TO
I
—
mu
pa
NA
s Do not puta fusein a neutral or ground circuit.
« Use a dedicated 120-volt 60-Hz, 20-amp, AC fused electrical circuit for this
cooktop. A time-delay fuse or circuit breaker is recommended. Do not plug mare
than one appliance into this circuit
Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water
pipes
This cooktop must be Earth grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electrical shock by providing a path
for the electric current. This cooktop is equipped with a cord having a grounding
plug. The plug must be firmly plugged into an outlet that is properly installed
and grounded in accordance with the local codes and ordinances. |f you are
unsure whether your electrical nutlet is properly grounded, have it checked by a
licensed electrician.
The cooktop is supplied with a 3-pronged grounded plug. This cord must be
piugged into a mating, grounded 3-prong outlet that meets ali local codes and
grdinances: If codes permit the use of a separate ground wire, we recommend
that a qualified electrician determine the proper path for this-oround wire.
Electrical service to the cooktop must canfarm to local codes, Barring local codes,
it should meet the latest ANSI/NFRA Ng. 70 - Latest Revision (for the US) or the
Canadian Electrical Code CSA C22.1 - Latest Revisions.
= It is the personal responsibility of the cookiop owner to provide the correct
electrical service for this cooktop.
Ui BW I
English 5
Bra WASH AN DFT AA Dhol A A §
HIDE Skis FA
Important safety information
Installation safety
dà WARNING
To reduce the risk of fire, electric shock, personal injuries. and/or death, obey the
following precautions.
« Have your cooktop installed and properly grounded by a qualified installer, in
accordance with the installation instructions. Any adjustment and service should
be performed only by qualified gas cooktop installers or service technicians.
« Do not attempt to service, modify, or replace your cooktop or any part of your
cooktop unless it is specifically recommended in this manual. All other service
should be referred to a qualified technician.
«Always Use new flexible cannectors when Installing a gas appliance. Do not use
pid flexible connéctors.
« Make sure the hold down brackets are properly installed on the cooktop, See the
installation instructions for more information
« Remove all tape and packaging materials,
« Remove all accessories from the cooktop. Grates and griddles are heavy. Use
caution when handling them,
« Make sure no parts came foase during shipping,
—
=
Le
=
Г
il
=}
La
=D.
os
—
ru
—
tar
—
be]
=
=
=
LF
г
и,
ни.
Make sure your cooktop is correctly installed and adjusted by a gualified
service technician or installer for the type of gas (natural or LP) you will use, For
vour cooktop to utilize LP gas, the installer must replace the 5 cooktop burner
orifices with the provided LP orifice set, and reverse the GPR adapter. These
adjustments must be made by a qualified service technician in accordance with
the manufacturer's instructions and all codes and requirements of the authority
having jurisdiction. The qualified agency performing this work assumes the gas
conversion responsibility.
Installation of this cooktop must conform with local codes or. in the absence
of local codes, with the National Fuel Gas Code, ANSI 2223 1/NFPA 54, [atest
edition. In Canada, the Natural Gas and Propane Installation Code, (5A B145.1
This cooktop has been design-certified by ETL according to ANSIZ21 1, latest
edition, and Canadian Gas Association according to CAN/CGA-1.1, latest edition
6 English
Bra ANR PO AA GREAT IA De Ei A
LO a PA
Location safety
dk WARNING
To reduce the risk af fire, electric shock, personal injuries, and/or death, obey the
following precautions.
= This cooktop is for indoor, household use only,
Do not install the cooktop in areas exposed to
the weather and/or water.
« Do not install the cooktop in a place which is
exposed to a strong draft
a Select 2 location where a grounded, 3- prong outlet is easily accessible.
« If the cooktop is located near a window, do nat hang long curtains or paper
blinds on that window.
« For the cooktop to ventilate praperly, there is enough clearance at the top. back,
sides, and underneath the cooktop. The vents allow the necessary exhaust for the
cooktop to operate properly with correct combustion.
« Make sure the wall coverings around the cooktop can withstand heat up to 194
"Е (90 "C) generated by the cooktop
«a Cabinet storage above the surface of the cooktop should be avoided. If cabinet
storage above the cooktop is necessary: allow a minimum clearance of 30 inches
(76.2 cm} between the cooking surface and the bottom of cabinets.
Cooktop safety
dk WARNING
To reduce the risk of fire, electric shock, personal Injuries, and/or death, obey the
following precautions
« Make sure all burners are aff when not in Use
« Do not use aluminium foil to line the grates ar
any part of the cooktop.
= Do not leave burners unatiended on medium or
high heat settings
« Before igniting, make sure ali burner caps are
property in place and all burners are level
—
——
=
—
ul
—
TO
I
—
mu
pa
La
« Always use the LITE position when igniting the burners and make surethe
burners-have ignited. If ignition fails, turn the knob to OFF and wait until the gas
has dissipated,
« When you set a burner to simmer, do not turn the knob quickly. Make sure the
flame stays an.
« Do not place any objects other than cookware on the cooktop.
« This cooktop is designed to cook with a wok or wok ring attachment. If foods are
flamed. they should anly be flamed under a ventilation hood that is on.
» Before removing or changing cookware, turn aff the burners.
Remove food and cookware immediately after cooking.
« Before remaving any parts of the burner for cleaning, make sure the cooktop is
off and completely cool.
« After cleaning the burner spreader, make sure it is completely dry before re-
assembling.
s To avoid carbon monoxide poisoning, do not pour water into the cooktop well
w hile cleaning.
« Select cookware that Is designed for top-cooktep cooking, Use cookware that is
large enough to cover the burner grates. Adjust the burner flames so that the
flames do not extend beyond the bottom of the cookware
= To avoid cookware discoloration, deformity, and/or carbon monoxide poisoning,
do not use cookware that is exceedingly larger than the grate.
« Make sure cookware handles are turned to the side ar rear of the cooktop, but
not over other cooktop burners.
Ui BW I
English 7
Bimal WASH ANI DFT AA Dhol ih De ВА вы ОТ
Eo A Fa
Important safety information
=
ur
E
rm
=
u
m
f=
Fe
Ls
=
=
=
—
=
=
La
=
—
um
8 English
Stand away from the cooktop white frying.
Always heat frying oils slowly, and watch as they heat, if you are frying foods at
high heat, carefully watch during the cooking process. If a combination of fats or
pils is to be used during frying, mix them together before heating.
Use a deep-fryer thermometer whenever possible, This prevents overheating the
fryer beyond the smoking point
Use a minimum amount of cil when shallow pan-frying or deep-frying. Avoid
cooking unthawed food or food with excessive amounts of ice
Before moving cookware full of fats ar oils, make sure it has completely cooled.
To prevent delayed eruptive boiling, always allow heated liquids to stand at least
20 seconds after you have turned off the burner so that the temperature in the
liquid can stabilize. In the event of scalding, follow these first ald instructions:
1. Immerse the scaled area In cool or lukewarm water far at least 10 minutes.
2. Do not apply any creams, oils, ar lotions
3. Cover with a clean, dry cloth
Gas cooktop components
What's in the box
Parts supplied
еее
surface burner grates (2) * Surface burner grates (3) * Cooktop burners and
30" Model: NA3ORS310F" 36" Model: NAZ6R5310F" caps (5) *
36" Model: NA36R5310F"
[ em
Cooktop burners and Screw 16) Regulator {1} °
Caps (4) IMAL1D 223, M4 L16 2 ea,
30" Model: NASORS310F Wife L7S 2 ева}
=
=, ©
Hold down brackets (2) * Foam tape
« Make sure you have received all of the supplied parts shown above.
« If your cooktop was damaged during shipping or you do not have all of the
supplied parts, contact your local retailer,
(E) NOTE
If you need an accessory marked with an ® (asterisk), please contact the Samsung
Call Center using the phone number listed on the last page of this manual ar visit
our on-line parts web site at ww»w.samsungparts.com
Bra PARAR AA CCAA EA à
1 o FA
Parts needed
Flexible metal
appliance connector
va In (ID) x 5 Tit
90-degree elbow
(optional)
Gas line shut-off
valve
Flare union adapter Flare union adapter
Minor in INPT] Xx % in (NPT) x % In
la In (10) (ID)
UT
135-degree elbow
(optional)
Tools needed
L |
c— És E
Flat-blade Phillips screwdriver Open-end or Pipe wrench (2)
SCreworiver
adjustable wrench
= К =
=) Ге 7 A)
[IICA
4” Nut driver Pencil and ruler Level Pipe joint compound
& =
>=
Utility knife
Soapy water
solution
Pliers Saber saw
=
ST
un
Г
=
=]
=
у
=
=
LS
j=
=
ГО
Не
Erez O POMAR Li CALA 0 add Y
English 9
Mo RA
Installation requirements
Pre-installation checklist
1. When preparing cooktop opening, make sure the Inside of the cabinet, and the
cooktop do not interfere with each other
2. Remove packing materials, grate boxes, regulator with literature, and literature
package from the cooktop before beginning installation.
Location requirements
BEFORE YOU BEGIN to install this appliance, refer to the following information,
dimensions, and clearances. These dimensions must be met for safe use of the
cooktop. The location of the electrical outlet and gas piping may be adjusted to
meet the following dimensions and clearances
Ji CAUTION
This cooktop has been designed to comply with the maximum allowable woad
cabinet temperature of 194 °F (90 ©), Make sure the wall covering, countertops,
L3 MAX
(30 mm
=
in
=
ab
7
—
=)
гы
ru
il
_
=
Dn
=
Ju
am
ar
i
a an Al
762 mi
2 MEN
14° MIN
(73.0 mmi
{304.8 mimi
307 - NA3D*5310F°
10 English
18” MIN
a (457 mm
y E
FL МЕЧ
(304.8 mm
and cabinets around the cooktop can withstand the heat (up to 194 °F (90 "O
generated by the cooktop. If not, discoloration, delamination, or melting may occur,
Maintain the following minimum clearance dimensions
L302LE mm)
(302.5 mem
36" - NA36°5310F*
© NOTE
All horizontal clearances must be m
above the cooking surface.
aintained for a minimum of 187 (457 mm)
PA
| [11.1 mm]
ni E
É
i ORAWER
Electrical outlet 13° |
(30:5 ond minimum |
below countertop В
|
|
|
|
|
' (E) NOTE
Allow "107 minimum vertical clearance
from the cooktop bottom (or 37”
minimum depth from the countertop) to
any combustible surfaces, including the
Upper edge ora drawer installed below the
cooktop.
Installation over built-in oven
E
—_— = =
— |
= Y OaHok
= [20° Trama
of countertop to
Cabiner des
View from Front of Cooktop
4 See built-in cven installation for complete
installation instructions
5 To temes oi 7 Lia
Hole From Countertop
Cm ANR AA OR iA De ES a lu
IDF Ski FA
Overall cooktop dimensions
A 30" Model
yt
Model NA30*5310F* NA36*5310F*
А 30° (762 mm] 367 (914:4 mm)
B 282 (715 mm; 336 (855.4 mm)
С 195/27 (4371 mm) 18%" (479.1 mm)
D 217 (532 mm] 21-533 mm)
E (Countertop to grate surface) 2777 (65 mm) 25 65 mm)
Е (Chassis Height) 31/47 (81.3 mm) 3/8 (79.3 mm)
Cutout dimensions of countertop
|
Fear wall
vert-ral
combustible
surface
A distance to combustible side
E Well above countertop thioth sides)
Model {H} Min: (1) Min: (J) Min.
MN&30 5310” 27€: 74 MM] 105/37 (4985 mm} | 2845 239 mm | 17 (3048 mm)
NAZIS 53 10F 3 [85.7 mm) | 191/27 (4658. mm} | 237: (660.4 mm) | 17 (3048 mm;
Installation dimensions with downdraft hood
(E) NOTE
Make sure the clearance dimensions when you install the cooktop with dewndraft
hood
N
Downdraft Hood
| —+
Ly (do mm Min
7
[ 13/2" (40 mel Min
Cooktop frame to dowrdraft hood
Cootktiop |
pri (K} Cuiout 10 dowrdratt hood
30" Model
36" Model
Model (K} Min:
MAZO 6310F" 25 (62 mm)
MAZO"5310F" 3 (6 mm]
=]
LL
il
a
—
= 3
=
—
Г
um
m
x
D
=
ра |
[о
a
=
=
pm
Bima ll WASH ANI DFT AA CRE A De BS dd Li
English 11
WHI Eck FA
Installation requirements
Single Oven Under counter Utility locations and dimensions
= Ol This cooktop can be installed above any
02 Samsung single built-in oven. Refer to
Installation manual of oven.
07 Gasand Electrical Connections for Gas
Cooktop Must be Located in an Adjacent
[on of cookiop
=
й E €
Accessible Location to the Right. !
H Do Sh o 1
Chassis cm
Power cord 39/47 ns TE Г |
[000 Cm) long Ea
ca A * Cas intet profrudes 1" [4.0 onl
LE PT male from bottom
gas inlet
Size
A Min. 334" (9.5 cm) Gas supply requirements
B 4° (10.1 cm) _
== === - Provide adequate gas supply
zZ C Min. 28 y Max. 28-/- 1Min. 724 cm; Max: 727 cm
т. a FE This cooktop is designed to operate at a pressure of 5 in {13 cm) of water column
+ В Min. 17 7 Мах. 11/4” (Мп. 32.5 cm / Мах. 3.2 cm a i
А on natural gas or 10 in (25 cm) of water column on LP gas (propane or butane).
к. r Lia" j г 77/8 | | 2 / À G5€ | . . 4
= E MO: 2774 Y MECENAS MA SE hake sure you are supplying your cooktop with the type of gas for which it is
я F 2:47 (61 cm) designed, Do not attempt to convert the appliance from the gas specified in this
1 y, и -
2 С Min 22" (Min 55.9 cm) manual to a different gas without consulting the gas supplier.
= H Max. 91/5" Max. 24.1 em} - Junction Box TES cooktop is convertible for USE on Hales) or propane gas. If VOL ende to use
= this cooktop on LP gas, conversion must be made by a gualified LP installer before
=- attempting to operate the cooktop.
For proper operation, the pressure of natural gas supplied to the regulator must be
between S in and 13 In (13 cm and 33 cm) of water column
For LP gas, the pressure supplied must be between 10 in and 13 in (25 cm and
33 cm) of water column
When checking for proper operation of the requéator, the inlet pressure must be at
east 1 in {2.5 cm) greater than the operating (manifold) pressure as given,
12 English
-
Erre PAE LA CCAA 0 Edd LE a EA ci Pd
=
The pressure reguiator located at the inlet of the cooktop manifold must remain in
the supply line regardless of whether natural or LP gas is being used.
5 NOTE
« The cooktop comes from the factory with a regulator In the shipping carton. Use
only the regulator provided, The regulator must be installed In the gas line that
runs from the cooktop gas inlet to the gas shut off valve.
« An external manual shut-off valve must be installed between the gas inlet and
the cooktop for the purpose of turning on or shutting off gas to the appliance.
+ Be sure the connectors are installed when you need coupling by a qualified
Installer:
« Never reuse old connectors when installing the cooktop. The use of old
connectors can cause gas leaks and personal injury, Always use new flexible
connectors when Installing a gas appliance,
Special gas requirements (gas models sold in Massachusetts)
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS:
dà WARNING
Gas leaks may occur in your system, creating a dangerous situation.
- Gas leaks may not be detected by smell alone
- Gas suppliers recommend you purchase and install a UL-approved gas detector
Gas detector should be installed in accordance with the manufacturers
instructions
« Cooktop must be installed by a qualified plumber or gas fitter by the State of
Massachusetts.
« A T-handle manual gas valve MUST be installed in the gas supply fine to your
cooktop.
« If a flexible gas connector is used to install your cooktop, multiple flexible gas
lines must not be connected in series,
Electrical requirements
dk WARNING
= It is the owners responsibility to make sure that the electrical service meets
electrical requirements and that he electrical outlet has been properly installed
by a licensed electrician.
s TO reduce the risk of fire, electric shock, or personal injury.
All cooktops
« Do not use an extension cord or adapter plug with this cooktop.
« This cooktop must be properly grounded
« Check with a qualified electrician if you are in doubt as to whether your cooktop
Is properly grounded
s Dog not modify the plug provided with vour cooktop — If it doesn't fit the outlet,
have a proper qutiet installed by a qualified electrician,
= All wiring and grounding must be done in accordance with local codes or, In the
absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70 -
Latest Revision (for the US) or the Canadian Electrical Code CSA {22.1 - Latest
Revisions and local codes and ardinances.
« Wiring diagram is located on the inside of the burner box,
s This cooktop is equipped with an electronic ignition system that will not operate
if plugged into an outlet that is nat properly polarized
Gas cooktops
« All gas models are equipped with a power cord with an equipment-grounding
conductor and a grounding plug,
« A 120-Volt, 60-Hz, AC, approved electrical service with 20-amp circuit breaker ar
time-delay fuse is requirad for all LL.S, and Canadian models.
English 13
Bimal WASH AAT Ad Dhl ih De ES ad A
aD Skis FA
RTE
=
o
im
=
=
ГО
==
=
ГО
=
ia
Installation instructions
Grounding Installing your gas cooktop
« All cooktops must be grounded for personal safety.
« The plug must be firmly plugged into a three-prong outlet that is properly
installed and grounded in accordance with all local codes and ardinances. In
the event of a malfunction or breakdown, grounding will decrease the risk of
electrical shack by providing a path for the electric current.
Do not use a damaged power plug or loose wall outlet.
Do not Use an extension cord or adapter with this appliance (E) NOTE
Do not, under any circumstances, cut. modify, remove, orotherwise defeat the
grounding (third) prong from the power cord, If the plug and the outlet do not
match or you have any doubt, have a qualified electrician install the proper
putlet. The customer should have the wall receptacle and circuit checked by a step 1. Unpack the cooktop
gualified electrician to make sure the receptacle is properly grounded.
« NEVER cannect ground wire to plastic plumbing lines, gas lines, ar water pipes.
IMPORTANT:
Please read the following Instructions, as well as the Important Safety Instructions
section at the front of this manual, completely and carefully BEFORE installing
and/or operating the gas cooktop. Improper installation, adjustment, service, ar
maintenance can cause personal injury or property damage.
To ensure proper installation, we strongly recommend that you hire a professional
installer.
Remove all packaging materials. Failure to remove packaging materials could
result in damage to the appliance,
Mm CAUTION
Failure tg follow these instructions can result in death, fre. or electrical shock.
Inventory all loose paris against the Parts supplied components listed on page 6.
Check for shipping damage and/or missing parts. Any damage and/or missing
Additional installation requirements for mobile homes ee VO ES EE ONE
The installation of appliances designed for-mobile home Installation must conform
with the Manufactured Home Construction and Safety Standard, Title 24 CFR: Part
3280 (formerly the Federal Standard for Mabile Home Construction and Safety, Г 1-1. Locate electrical outlet and gas shut-off
Title 24, HUD, Part 280} or, when such standard is not applicable, the Standard 7 valve beneath cabinet
far Manufactured Home Installations, latest edition {Manufactured Home Sites. 2. Apply the foam tape around the edge of
Communities and Set-Ups), ANSI A225.1, latest edition. or with local codes. In the cutout opening. Do nat overlap the
Canada, mobile home installation must be in accordance with the current CAN/CSA foam strips
7240/MH Mobile Home Installation Code, » The foam strip helps avoid damage
to the underside of the cooktop from
|: 3 debris and helps the cooktop sit fiat on
Uneven counters,
3. Protect surface of cooktop
» Place a towel or tablecloth onto the
countertop,
Step 2. Installing the cooktop
=
т
Г
fis
==
=
т
а!
я
=
=
A
=
т
14 English
и
Bra PAR A Сай СТА вле ES 1-й a "oe o Pad
Correct installation
™ 4, With bottom side first, gently put the
cooktop down.
« Make sure the front of the countertop is
parallel to the cooktop
s Make final check that all required
clearances are met.
Front of Lng
C= T_T 3
==" Hold down E *
N= bracket holes EA
Hold Down Bracket Installation
Y 8. Secure the cooktop to ihe countertop
using the two provided hold-down
brackets as shown,
Hold down bracket install quide
Case 1. Case 7,
E AT
eh
= or © side wall ol
undercounter es Fi
= Ra ; : gt 5
EN += cabinet ail
| <
E Had on
Ш | bracket
МА 110 sore “Hold СМ ден „=,
= pri Ma LEO screw X
MELLE seren) | Wile L75 screw
Step 3. Connect the cooktop to gas supply
Shut off the main gas supply valve before disconnecting the old cooktop and leave
it off until the new hookup has been completed. Don't forget to relight the burner
on other gas appliances when you turn the gas back on.
Because hard piping restricts movement of the conkiop, the use of a CSA
Internationai-certified flexible metal appliance connector is recommended unless
local codes require a hard-piped connection.
A WARNING
If the information in thls manual is not followed exactly, a fire or explosion may
result, causing death, personal injury, ar property damage
- Go not store or use gasaline or other flammabie vapors and liguids in the
vicinity of this or any other appliance
- WHAT TO DO IF YOU SMELL CAS:
« DO NOT light 2 match, candle, or cigarette.
« 00 NOT try to light any apphance:
« DO NOT touch any electrical switch,
« 00 NOT use any phone in your building.
« Clear the room, building, or area of all occupants
Bra PAR A CCA AO ES ai 15
English 15
Ae hole o |
= Meld FM
=
та
=
al
LF
al
=
=
A
3
ss
=
=
a?
т
|
E
Ш
af
=
и
ra
it
E
=
m
ый!
=
=
ия
Installation instructions
« Immediately call your gas suppfier from a neighbor's phone. Follow the gas
suppliers Instructions.
« [Tf you cannat reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service
agency, or gas supplier:
Do not install the cooktop without also installing the Included gas regulator. Do
not use the cooktop without the réquiator installed,
Ensure that the arrow on the regulator points: in the direction of the gas flow,
towards the cooktop.
- [Oo not apply excessive pressure when tightening gas connections and fittings.
Test the gas lines far leaks as instructed before usé. Do not use à flame to check
for leaks,
Never Use an old connector when installing a new cooktop. If the hard-piping
method is used, you must carefully align the pipe; the cooktop cannot be moved
after the connection is made.
Ta prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with
Teflon an all male {external} pipe threads.
1. Attach the gas pressure regulator {included with the cooktop) to the cooktop
pipe nipple inlet, For tight installations. the regulator may be installed upstream
from the pipe nipple, anywhere between the shut-off valve and the cooktop.
For best performance, minimize gas pressure loss by attaching the regulator as
close as possible to the cooktop gas inlet
2. Complete connection af the gas supply to the cooktap by installing a flexible
gas line between the pressure regulator and the shut-off valve
А WARNING
Do not exceed 25 ft-lbs of torque when making gas line connections
Overtightening may crack the pressure regulator resulting in a gas leak.
16 English
Flexible connector hookup
Installer: Inform the consumer of the location of the gas shut-off valve
| (E) NOTE
The gas shut-off valve should be installed
Gas Shut-Off valve
in an accessible location in the gas piping,
ie external to the appliance, for the purpose
Sa ; ;
г of turning on or shutting off the gas to the
Tubing Line appliance.
Connector to Comino
16-ff man)
T
Pressure
Regulator |
adapter
Step 4. Check for gas leaks
dk WARNING
To prevent death, personal injury, explosion, and/or fire hazard, DO NOT use a
flame to check far gas leaks.
When using test pressures greater than % psig to pressure-test the gas supply
system of the residence, disconnect the cooktop and individual shut-off valve
from the gas supply piping. When using test pressures of ¥% psig or iess to test
the gas supply system, simply isolate the cooktop fram the gas supply system by
closing the individual shut-off valve.
1. When all connections have been made, make sure all cooktop controls are in the
aff position and turn on the main gas supply valve
2. Use a liguid leak detector at all joints and connections to check for teaks in the
System
3. Tighten all connections if necessary to prevent gas leakage in the cooktop or
supply line:
Bimal WASH ANID Ad Dhl ih Dl ES de
aI SEE FAM
Step 5. Electrical connections
dà WARNING
« Disconnect all electrical power af the main circuit breaker or fuse box before
Installing
« BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 14
in this manual. Improper connection af the grounding plug can result in a rick of
electric shock,
a All gas cooktops come with a power cord. The power cord is connected to the
bottom of the cooktop. Piease review -Efectrical reguirements” ón pages 13.
« Thé electrical system, including the power cord, is preinstalled and prewired at
the factory. Altering any part af this system may result in a short or gverload
1. Plug In the power cord. Make sure the outlet meets local or national electrical
codes as referenced on pages 13,
2. Check the gas supply line to make sure it did not get damaged and it stayed
connected during positioning,
Step 6. Assemble the cooktop burners
A CAUTION
« Oo not operate the cooktop burners without all burner parts in place,
« Be careful not to push in any cooktop controls while removing the cooktop
burner. A slight electrical shock might result which could cause you to knock
over hot cookware.
« Do not remove the top or touch the efectrode of any burner while another
burner is turned on. Electrical shock might result
— = the cooktop burner manifolds as-shown
pn the left. The electrodes will fit into
e 2 sure the cooktop burner heads are flat
and parallel with the cooktop,
each cooktop burner head.
££ 1. Position cooktop burner heads on top of
the slot in the bottom of the heads. Make
30" - NA30°5310F* 2. Place the matching size caps on top of
36" - MA36*5310F"
aya
A
Bra PARAR A CCAA A EA a 17
English 17
E cia PA
=
та
=
al
LF
al
=
=
A
3
ss
=
=
a?
т
Installation instructions
Round Burner head Burner Cap
1. Orient the burner head so that the
opening for the electrode lines up with
the electrode
* т. Match the burner caps to the burners by
size, and then re-install the caps an the
burner heads.
/h, CAUTION
Make sure each cap is re-installed on the
A correct burner head, 1= centered on the
burner head, and lies flat.
E “2. Install ihe burner head so that the
electrode passes through the opening far
the electrode. Make sure the burner head
ies flat an the stove top.
\, + 4
i = He ` CAUTION =
Burner Head MA > Л CAUTION
Make sure all burner components (heads
: Make sure all burner companents (heads
and caps} are reinstalled properly. They `
o а. ) J and caps) are reinstalled properly. They
will be stable and rest flat when correctly | be stable and rest flat i
Ihetalled. wi e stable and rest flat when correctly
Installed
3
ы
= ho J
=
18 English
и
Bima ll WASH AAR Ad Dela ih De ES aid de a whine SEI FA
-
Step 7. Check the ignition of cooktop burners
Check the operation of all cooktop burners after the cooktop has been installed
and assembled, gas supply lines have been carefully checked for leaks, and
electrical power cord has been plugged in
r A,
To turn on a cooktop burner
1. Push in and turn the control knab for that
cooktop burner to the Lite position. The
“clicking” sound indicates the electronic
ignition system is-operating properly. The
burner will light in about 4 seconds, after
the air has been purged from the supply
À ne,
2. After the burner lights. turn thé cantrol
knob to the desired setting. The “clicking”
sound will stop and the flame height will
change from Max. to Min. during turning
the control knob
3, Repeat steps 1 and 2 to check the
operation of each cooktop burner in
succession,
© NOTE
« If the burner does not light within 4 seconds, turn the knob off and wait one
minute before trying again
= When you push inand turn the controf knob, all spark igniters will make a series
of sparks, but only the burner turned to Lite will light.
Step B. Checking the flame quality
Al combustion flames need 10 be visually checked to determine their flame
quality
Mm CAUTION
If vou attempt to measure the flame, please use caution. Burns could result.
(oe
000000 ©
000000 9
* 1 Soft blue flames— Normal for natural gas
operation
2. Yellow tips on outer cones—Normal for
LP gas operation.
3. Yellow flames—Abnormal for any gas
operation; call for service
(E) NOTE
If burner flame locks like 3, the cooktop
should not be used until it is serviced. Call
for service. Normal burner flames shall look
like 1 or 2, depending on the gas type you
USE,
English 19
Bima ll WASH ANF Ad Dhl ih De ES ad 1e
whine SEI FA
=
та
=
al
LF
al
=
=
A
3
ss
=
=
a?
т
Installation instructions
Step 9. Install the grates
36" Model: NA36R5310F"
(E) NOTE
Install the grates as instructed below for longest life. When installed properly. the
apenings in the grates are centered over the burners,
The three cooktop grates are designed to fit in specific positions an the cooktop.
For maximum stability, these grates should only be used in their proper positions.
« Place the left and right grates so that the thicker side af the right grate lines up
with the right side of the cooktop and the thicker side of the left grate lines up
with the left side of the cooktop.
« The center grate must be installed with the filled-insection, marked with the
word ‘BACK, oriented towards the back of the cooktop
The center grate has two overhangs to help you locate the side grates correctly. It
hits the side grates when you locate wrong direction. See the illustration below,
Pa “a
i N LS
1 I "
+ ar
в
ет
ня
Ш
al
= =
=
=
af
НН
—_
|
=
—
=
=
Ч
To replace the grates correctly, follow these steps.
1. Orient the center grate as noted direction.
2. Gently lower the legs-of the center grate so that leg dimples can match
embDosses on CODKtOp
3. Locate thicker side of remaining two grates to face outside of cooktop
4. Gently lower the legs of two remaining grates Into the corresponding embosses
without interfering with center grate overhang
Picker Sache mel
be on the leí
20 English
и
Bimal WASH AAT Ad Dela iA De ES ad a
-
WDE ECE FAM
30" Model ; NA3OR5310F"
12) NOTE
Install the grates as instructed below for longest fife. When instalied properly, the
apenings in the grates are centered over the burners.
The two cooktop grates are designed to fit in specific positions on the cooktop.
For maximum stability, these grates should only be used in their proper positions.
« Place the grate with filled-in section on the right side to the left side, and the
grate with filled-in section on the left side to the right side
« Each grates must be installed with the filled-in section, marked BALK, oriented
towards the back of the cookiop,
To replace the grates correctly, follow these steps.
1. Orient the center grate as noted direction.
2. Gently lower the legs-of the Left grate so that eg dimples can match embosses
an cooktop.
3. Locate filled-in section of right grate to face back side af the cooktop
4. Gently lower the legs of right grate into the corresponding embosses without
interfering with left grate overhang,
Filled-in section od
left grate
Fillegt-In section of
right grate
=
та
=
al
LF
al
=
=
LA
3
ss
=
=
a?
т
English 21
и
Gr ANR PC AA CRE A Ad 21 a Mo A FA
-
Installation instructions
Step 10. Final installation checklist
di WARNING
« To ensure a safe and proper installation, the following checklist should be
completed by the instalier to ensure that no part of the installation has been
overlooked
a Proper installation is the responsibility of the homeowner, The impartance of
proper installation of your Samsung cooktop cannot be overemphasized.
You have just completed installing your cooktop. Make sure all control knobs are
in the off position The following is a checklist to confirm your cooktop is safely
installed and ready for operation
- Gas line has been properly connected to the cooktop, The gas has been turned
on
AH connections have been checked for leaks.
- The cooktop is plugged into the properly grounded etectrical receptacle
- The cooktop burners.and grates have been properly assembled,
- All burners have been tested for proper operation.
an
=
Qu
El
=
=
=
=
=
=
=
=
BE
=
=
=
22 English
LP (Propane) conversion instruction
dk WARNING
« This conversion must be performed by a qualified installer or gas supplier in
accordance with the manufacturers instructions and all codes and requirements
of the authority having jurisdiction. Failure to follow ALL in structions could
result in serious injury or property damage. The qualified agency performing this
work assumes responsibility for the conversion.
« Know the location of the gas shut-off valve and how to shut it off if necessary.
« Unplug ar discannact power before servicing.
« Do not operate the cockiop burners when using LP gas before converting the
pressure regulator and burner orifices for LP gas use. Failure to do so could
cause high flames and toxic fumes which can result in serious injury,
« Do not mix Up or substitute LP gas burner orifices during conversion process.
Improper orifice placement will effect burner and cooking performance and could
result in personal injury and/or product damage.
All Samsung gas cooktops are manufactured and shipped to be used with natural
gas. The cooktop are also shipped with LP Conversion Kits, so the cooktop can
be converted to De used with LP gas. The kits-consist of a set of properly-sized
burner orifices to be used in the cooktop burners. These arifices will be positioned
in a sheet of cardboard and placed in a plastic bag. The bag is placed with a user
manual, The arifice in the pressure regulator is a dual-purpose orifice, one side for
natural gas and the other for LP gas.
Bima ll WASH AAR: Ad Dhol ih De ES ad 2E
ale SEIZE FAM
Supplied parts
The following parts make up the LP conversion Kit
Ta FI Fina en I mr FI Te
mo вино |
и (5%
| £2.) [Че
HA bi
FE mm
(© ) (о )
4 Re.
JE FONE
GET DESSIA
DESE-DOTENA
TAÿSY MOZILE KIT)
NA30"5310F"
requires spud removal and relnsía
| OATFICESACRIFICES/O8IFICKOS
DCI6-007434
VASSY MGZILE-HITI N
NA36" 53106"
The all orifices positions are marked on the provided sheet. The spud in the
pressure regulatar is factory-installed for Natural Las (NC) use LP conversion
ation for LP use
BURNER ORIFICE SIZES AND OUTPUT RATINGS
(LP Gas [Propane] 10 in WEP)
Burner Location BTU Rate Orifice size [mm]
RE" 12500 1.05
ВЕ? 11500 1.04
EF! 11500 1.04
LF? BOCO 0.83
RA 4500 0.62
LR E000 0.83
Center * 12500 1.06
* Model NASD 53 10F"
“ Model NA36*5310F”
{Matural Gas 5 in WEP]
BURNER ORIFICE SIZES AND OUTPUT RATINGS
Burner Location BTU Rate Orifice size [mm]
ВЕ' 17000 1.92
ВЕ? 13000 1.64
LF’ 13000 1.64
LF? 10000 1.4
RR 5000 1:01
LA 10000 1.4
Center 17000 192
! Model NA30 53106"
: Model NA36*5310F”
© МОТЕ
Orifice markings:
115 - Denotes 1.15 mm arifice size opening.
English 23
Bimal WAMBRNIORG LA CAE А Не В в A
IDF DAT
=
T°
—
al
eu
—
=
==
| J
=
Ki
—
+
| =
Г
—
=
a |
и
ты
Installation instructions
Required tools Converting the pressure regulator
(E) NOTE
— == If vou are-using LP gas to fuel the cooktop, the following steps. and conversions
must be made before the flames can be adjusted.
1. Using your Angers, turn the cap. And carefully look at the spring retainer to
Adjustable wrench 77 open-end wrench Screwdrivers: Phillips locate the NAT or LP position
Small flat-bladed NuUt drivers: #2" Or
précision screwdriver 7 mm
Spring
e Retainer
To convert your for use with LP gas, perform the following steps and procedures:
1. Disconnect electrical power to the cooktop. Unplug the cooktop power cord, trip
the circuit breaker, or remove the fuse from the fuse box. LP./Propane
2. Shut off the gas supply to the cooktop. Close the manual shut-off valve to the Position
cooktop.
Pressure Regulato!
ou 2. Turn the spring retainer over by rotating it 90 deg., pull it frem the cap, turn the
À spring retainer over so that LP is showing, insert it back into the cap, and then
= rotate it 90 deg. Into position
= 3. 5crew the cap back onto the regulator and tighten,
-
24 English
“я
Bima ll WASH ANI DFT Ad Dhol ih De BS dd 5 a MC a FA
-
Converting the cooktop burners
© NOTE
If you are using LP gas to fuel the cooktop; the following steps and conversions
must be made before the flames can be adjusted
1. Lift off the cooktop burner caps and the cooktop burner heads from thé cooktop
burner manifold cups,
Cookiop Burner Laocatons
E с
ше ‘
2. Using a 7/21" Or 7 mm nut driver, remove the burner orifice from the bottom of
each burner manifoid cup.
7 нот ВН
Г фе. cn
Cooktop te Ч ¢ нА!
- Y
Burner Orifice \ \ LE 5)
% te ~~,
© NOTE
Save these orifices and note their positions for future conversions back to natural
gas
3. Locate the LP conversion orifices that were shipped with-the cooktop.
4, Identify the proper orifice by orifice size for each of the cooktop burners
5. Install the proper orifices in each of the burner manifold cups and tighten with
a/a Or 7 mm nutdriver
(E) NOTE
Any other placement of orifices could result in dangerous operating conditions
and/or poor cooking results,
6. 5et all burner heads on top of the manifold cups in the same location as
they were removed. The hole on the side of the burner heads goes over the
electrodes. The burner heads are carrectly installed when they are flat on the
top of the manifold cups.
7. 5et all burner caps on top of the burner heads. These are also flat when they are
installed ta ensure proper safe opération
English 25
Bima ll WASH ANF Ad Dela ih De ES indd 5
MOE EEE FA
=
та
=
al
LF
al
=
=
LA
3
ss
=
=
a?
т
Installation instructions
Adjusting low flame setting on cooktop burners Combustion flame quality
All Cooktop burner flames should be checked at their lowest setting. Use the в 3 \ 1. Soft blue flames- Normal for natural gas
following steps to check and adjust the cooktop burner settings. | | | | | | | (1) Operation,
2. Yellow tips on outer cones—Marmal for
® NOTES LF gas operation
« Low =etting adjustments should always be made with two or more burners 3. Yellow flames—ábnormal for any gas
operating at the same time (2) operation, Further adjustment required.
« Call for service when you need to adjust the inner flame af the cooktop center
burner settings
1. Turn on two or more cooktop burners and set them between MED and HI. (3)
2. Quickly turn one of the control knobs counterclockwise to the lowest setting. | : : J
The flame should stay lit. If the flame flutters or goes out, adjust the bypass
valve on the control valve for that burner.
3. Pull the contral knob far that burner straight off Additional low flame check
1. Quickly open and close the cabinet door while the cooktop burner is set on LO,
i" “ 4. Using a small flat-bladed screwdriver,
- If the flame is extinguished, increase the low flame setting and repeat the test
adjust the bypass valve screw in thé base
Flat-biaded af the valve stem. Turn the bypass valve until the flame is stable
=cresadriver screw counter clockwise to increase the 2. Turn the knob from HÍ to the lowest setting quickly, IT the flame goes out at the
flame size lowest setting, increase the low flame setting and repeat the test until the flame
is stable,
А WARNING
= } To 1: Do not completely remove the valve set screw from the valve stem. The valve
nr” — Je _ set screw is an intégral part of thé gas valve assembly, Removing the valve set
LE el A screw will cause gas to leak.
2. After adjusting the valve set screw, inspect the assembly for gas feaks,
5. Replace control knob and recheck the low flame setting.
6. Repeat step 1 thru 5 to check and adjust the low flame settings on the
remaining cooktop burners.
в
ot
La
Li
al
=
=
—
in
—
—
=
—
Го
p=
=
TT
26 English
и
Bima ll WASH ANF Ad Dsl AO ES add Dn a MOE EEE FA
Memo
Erma ll WLR SHI PGA, [Tel ОКА Pad 7 a WHEE SEIS FM
=
QUESTIONS OR COMMENTS?
SAMSUNG
[m] [=] Scan the OR code* or visit
m= AA samsung .comyspan
to view otr helpful
How-to videos and Live Shows
[=] "Requires reader io be пез а Ра an your
Srér Pen OT EEE оо ЗГЛаГ Вы Кале!
COUNTRY
CALL
OR VISIT US ONLINE AT
LESA
Consumer Electronics
1-800-SAMSUNG (726-7864)
WWW SIMsUNQ.-COM/US/sUppart
CANADA
1-800-SAMSUNO(7 26-7864)
NAN Samsung.com/ca/support (English)
WWW Samsuno.com/ca_fr/support [French]
Ben ANR PC AA DRE LA Dé EA add I=
[=] [=]
alle
CGHZ-011334-00
MOE 0 Pad