advertisement
H-20
5
WATER SOLUBLE PASTE FLUX
TECHNICAL SPECIFICATION: Oatey H-20 5 Water Soluble Paste Flux cleans and fluxes most commonly soldered metals including copper, brass, zinc, galvanized iron, lead and tin or copper-coated metals. Fluxing is a critical step in the soldering process. H-20
5
Paste Flux is lead-free and ideal for copper systems including fire sprinkler, hydronic heating, potable water service and DWV piping. H-20 5 Paste Flux remains active up to 700° F. H-2O 5 Flux complies with CA & VT lead content regulations.
PHYSICAL/CHEMICAL PROPERTIES
Appearance Off-White to Light Yellow Paste
Shelf Life 1 year from manufacture date
Solder Temp. Range 400-700 F pH 3-4
DIRECTIONS FOR USE
Paste Fluxes require only a small amount of flux applied to the joint. Clean all surfaces before soldering. Apply small amount of flux inside the fitting and outside of the pipe. Heat to temperature required for soldering. Do not overheat the piping. For small diameter piping, direct the heat near the joint. For large diameter piping, move the heat around the joint to ensure adequate solder flow around the circumference of the joint. NOT FOR USE
WITH ALUMINUM, STAINLESS STEEL OR MAGNESIUM.
DO NOT USE ON ELECTRICAL PARTS.
When soldering process is complete, allow joint to cool undisturbed. Remove any flux residual with a damp cloth. Do not store H-20
5
Paste Flux above 120° F.
PRECAUTIONS
Read all cautions and directions carefully before using this product. Apply flux with brush- do not apply with fingers.
Wash hands thoroughly after use and before eating. Wear safety glasses with side shields and rubber gloves. EYE AND
SKIN IRRITANT. HARMFUL IF SWALLOWED. VAPOR MAY BE
HARMFUL. Eye or skin contact may cause intense irritation and injury. In case of contact with eyes or skin, flush with water and seek medical attention immediately. If swallowed,
DO NOT INDUCE VOMITING. Drink water and call physician or poison control center immediately. Ingestion of this product may cause gastrointestinal distress. If inhaled, get fresh air and seek medical attention if ill feelings persist.
Keep container closed when not in use. DO NOT REUSE
EMPTY CONTAINER. KEEP OUT OF REACH OF CHILDREN.
Refer to material safety data sheet for more information.
For emergency first aid help, call 1-877-740-5015.
COMMON APPLICATIONS
Oatey H-20
5
Lead Free Paste Flux can be used to solder most commonly soldered metals including copper, brass, zinc, galvanized iron and tin or copper-coated metals.
Consult Oatey Technical Department for applications not specifically referenced above.
INGREDIENTS (CAS Number)
Triethanolamine Hydrochloride (637-39-8)
Zinc Chloride (7646-85-7)
Ammonium Chloride (12125-02-9)
Surfactant Blend (N/A)
Inert Fillers (N/A)
COMPLIANCE & LISTINGS
DESCRIPTION
NSF Listed to Standard 61
IAPMO Listed Lead-Free Flux
Complies with CA & VT lead legislation
Meets ASTM Standard B 813
PACK CARTON WEIGHT PRODUCT
NUMBER
30130
30131
30132
30133
53067
C-1
1.7 oz. H-20 5 Water Soluble Paste Flux
4 oz. H-20 5 Water Soluble Paste Flux
8 oz. H-20 5 Water Soluble Paste Flux
16 oz. H-20 5 Water Soluble Paste Flux
1.7 oz. H-20 5 Water Soluble Paste Flux with Brush – Carded
Visit www.oatey.com
for updates
12
24
24
12
12
2 lbs.
7 lbs.
16 lbs.
15 lbs.
2 lbs.
1/2010
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement