Quick guide
ReSound LiNX 2 ™ MIH
My hearing aid information
Product: ReSound LiNX 2
Model: MIH
Serial number ( R ) :
_______________________________
Serial number ( L ) :
_______________________________
Battery size: 312 or 13
Programs:
(if set up by your hearing care professional)
PROGRAM WHEN TO USE BEEPS
1 1
2 2
3 3
4 4
Volume control (C):
(if set up by your hearing care professional)
ACTION RESULT
Rotate forward
(toward your face)
Volume increases
Rotate backward
(away from your face)
Volume decreases
Get to know your hearing aid
A.
Microphone
B. Battery door
C.
Program button
D.
Retrieval line
E.
Vent
A
B
E
C
D
View ReSound hearing aid tutorial videos at youtube.com/resoundus.
F.
Wax guard
G.
Manufacturer
H.
Serial number
I.
Model
F
GN R eSound
LS xMIH
G
H I
D
What you need to know
Getting started: On/Off function
ON: Insert battery & completely close battery door (B).
Program 1 will be active.
ON
OFF: Open the battery door (B).
Use
fingertip to pull it all the way.
OFF
Inserting/Replacing the battery:
1. Open the
battery door (B)
completely by
using your
fingertip.
2. Remove protective sticker from
battery and wait 2 minutes before
inserting the
battery into the
hearing aid to
allow full activation of the battery.
3. Insert the new battery
with the positive side
(flat side) in the correct
position, as shown.
4. Gently close the battery door (B).
If it doesn’t close easily, check to
see if the battery is upside down.
Regular care & maintenance
Daily: Clean your hearing aid.
Keep your hearing aids dry. Clean the hearing aids using a soft cloth or tissue.
Monthly: Change the wax guard (F) or see your hearing care professional.
For changing CeruSTOP ™ (white) wax guards, complete the following steps:
Removal: Insert the removal side of the wax guard tool into the used wax guard so that the shaft of the tool is touching the rim of the wax guard. Slowly pull the wax guard straight out.
removal side
Wax guard tool replacement side
Insertion: To insert the new wax guard, gently press the replacement side of the wax guard tool straight into the hole of the sound outlet until the outer ring lies flush with the outside of the receiver. Pull the tool straight out. The new wax guard will remain in place.
For changing HF3 wax guard (F), complete the following steps:
1. Brush the sound
outlet area with
the sound outlet
pointed down.
2. Insert the threaded end of the wax
guard tool into the used wax guard,
and rotate clockwise.
4. Discard
the used
guard in
the slot
located
in the wax guard kit by pressing it
into the center, sliding it to one end
of the slot, and pull until the filter
is discarded.
5. Flip the wax guard
tool around, locate
a new guard in the
dial, and press the
tip of the tool into
the center of the dial.
6. Gently pull the new
filter out of the dial.
7. Press the new guard to the canal
tip
tool gently side to side and pull it
away from the hearing aid.
3. Gently pull until
the used guard is
removed.
Troubleshooting
SYMPTOM CAUSE
No sound Battery door not closed
Dead battery
Battery door will not close
Blocked wax guard
Not loud enough
Excessive whistling/ feedback
Blocked sound outlet
Change in hearing, volume too low
Excessive ear wax
Incorrect placement in ear
Excessive ear wax
If none of the above
POSSIBLE REMEDY
Turn on by closing the battery door (B)
Replace battery
Insert battery properly
Replace wax guard (F) or consult your hearing care professional
Change wax guard (F) or consult your hearing professional
Consult your hearing care professional
Consult your hearing care professional
Re-insert hearing aid carefully
Clean guard/consult your hearing care professional
Consult your hearing care professional
If there are any other problems not mentioned in this guide, please contact
ReSound or your hearing care professional.
View ReSound hearing aid tutorial videos at youtube.com/resoundus.
For more information
Refer to the user guide included in your hearing aid box.
Your hearing care professional can be reached at:
View ReSound hearing aid tutorial videos at youtube.com/resoundus.
Manufacturer according to FDA
ReSound North America
8001 E. Bloomington Freeway
Bloomington, MN 55420
1.888.735.4327 resound.com
ReSound Government Services
8001 E. Bloomington Freeway
Bloomington, MN 55420
1.800.392.9932 www.resound.com/veterans
Manufacturer according to Health Canada
ReSound Canada
303 Supertest Road
Toronto, Ontario M3J 2M4
1.888.737.6863 resound.com
400560011 Rev E 2016.11
400560011