Zebra TC25 User Guide
Annonce
Annonce
TC25
Rugged Smartphone
MN-003308-01 Rev. A
Copyright
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. Google, Android, Google Play and other marks are trademarks of Google LLC; Oreo is a trademark of Mondelez International, Inc. group. All other trademarks are the property of their respective owners.
©2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/ copyright .
WARRANTY: For complete warranty information, go to www.zebra.com/warranty .
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula .
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra
Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if
Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Revision History
Changes to the original guide are listed below:
Change Date
-01 Rev A 3/2018 Initial Release
Description
2
Table of Contents
3
Table of Contents
Adding an App Shortcut to the Home Screen ................................................. 43
Adding a Widget to the Home Screen ............................................................. 43
Moving Items on the Home Screen ................................................................. 44
Removing an App Shortcut or Widget from the Home Screen ....................... 44
Entering Numbers, Symbols and Special Characters ........................................... 46
4
Table of Contents
Silence Sounds During Events and Meetings ....................................................... 49
5
Table of Contents
6
Table of Contents
Responding with a Private Response ........................................................... 102
Disabling PTT Express Voice Client Communication .......................................... 102
Barcode Scanning with Internal SE2100 Imager ................................................. 109
SE2100 Basic MultiBarcode Mode ............................................................... 111
SE4710 Basic MultiBarcode Mode ............................................................... 113
Scanning with RS507/RS507X Hands-Free Imager ................................................... 115
Pairing the RS507/RS507X/RS6000 Hands-Free Imager .......................................... 117
Pairing Using Bluetooth Human Interface Device ............................................... 117
7
Table of Contents
Indonesian configurations do not support LTE. ............................................ 122
8
Table of Contents
Removing the Device from the Trigger Handle ................................................... 150
9
Table of Contents
10
About This Guide
This guide provides information about using the TC25 Rugged Smartphone and accessories.
NOTE : Screens and windows pictured in this guide are samples and can differ from actual screens.
This guide applies to model numbers: TC25AJ, TC25BJ, and TC25CJ.
Configurations
This guide covers the following configurations:
Table 1 Configurations
Configuration
TC25AJ-10B101xx
TC25AJ-10C102xx
TC25BJ-10B101xx
TC25BJ-10C102xx
WAN/LAN/PAN GMS
WAN/LAN/PAN GMS
WAN/LAN/PAN GMS
WAN/LAN/PAN GMS
NOTE: Indonesia configurations do not support LTE.
2 GB/16 GB
2 GB/16 GB
2 GB/16 GB
2 GB/16 GB
SE2100
SE4710
SE2100
SE4710
Chapter Descriptions
Topics covered in this guide are as follows:
•
provides information on getting the TC25 up and running for the first time.
•
Using the Device provides information for operating the TC25.
•
Calls provides instructions for making phone calls.
•
provides information on using applications installed on the TC25.
•
Data Capture provides information on capture barcode data.
•
provides information on the various wireless options.
11
Yes
No
Yes
No
Blank
2-Pin
Blank
2-Pin
•
provides information on using the accessories for the TC25.
•
Maintenance and Troubleshooting
includes instructions on cleaning and provides troubleshooting solutions for potential problems during TC25 operation.
•
provides the technical specifications for the TC25.
Notational Conventions
The following conventions are used in this document:
• Bold text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen.
• Bullets (•) indicate:
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
Related Documents and Software
The following documents provide more information about the TC25 rugged smartphone.
• TC25 Quick Reference Guide, p/n MN-003052-xx
• TC25 Regulatory Guide, p/n MN-003053-xx
• TC25 Rugged Smartphone Integrator Guide, p/n MN-003307-xx
For the latest version of this guide and all guides, go to: zebra.com/support .
Service Information
If you have a problem with your equipment, please use the Self-Help support resources available at www.zebra.com. If the support provided via the Self-Help resources is not sufficient, you may contact Zebra
Global Customer Support for your region. Contact information is available at: zebra.com/support .
When contacting support, please have the following information available:
• Serial number of the unit
• Model number or product name
• Software type and version number.
Zebra responds to calls by email, telephone or fax within the time limits set forth in support agreements.
If your problem cannot be solved by Zebra Customer Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during
12
shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your Zebra business product from a Zebra business partner, contact that business partner for support.
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email to
.
13
Getting Started
This chapter provides information for getting the device up and running for the first time.
Unpacking
Carefully remove all protective material from the device and save the shipping container for later storage and shipping.
1. Verify that the following were received:
• touch computer
• Regulatory Guide.
2. Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global Customer
Support center immediately.
3. Prior to using the device for the first time, remove the protective shipping film that covers the scan window, display and camera window.
14
Features
Figure 1 TC25 Front View
9
11
10
13
12
8
7
1
2
6
5
4
3
7
8
4
5
2
3
9
10
11
Table 2 Front View Features
1
Number
6
Scan Button
PTT Button
Microphone
Item
Power Contacts
USB-C Connector
Function
Initiates data capture (programmable).
Yellow button: TC25 with SE4710 imager.
Gray button: TC25 with SE2100 imager.
Initiates push-to-talk communications (programmable).
Use for communications in Handset mode.
Provides power for charging the TC25.
Provides USB host and client communications, and device charging via cables and accessories.
Speaker Provides audio output for video and music playback. Provides audio in speakerphone mode.
Displays all information needed to operate the TC25.
Touch Screen
Charging/Notification LED Indicates battery charging status while charging and application generated notifications.
Data Capture LED
Microphone
Receiver
Indicates data capture status.
Use for communications in Speakerphone mode.
Use for audio playback in Handset mode.
15
Table 2 Front View Features (Continued)
Number
12
13
Item
Light Sensor
Proximity Sensor
Function
Determines ambient light for controlling display backlight intensity.
Determines proximity for turning off display when in handset mode.
Figure 2 TC25 Rear View
7
8
9
6
1
5
2
3
4
5
6
3
4
7
8
Table 3 Back View Features
1
Number
2
9
Item
Imager Window
Power Button
Hand Strap Mount Point
Function
Provides data capture using the imager.
Turns the display on and off. Press and hold to reset the device or power off the device.
Camera Flash
Camera
Provides illumination for the camera.
Takes photos and videos.
Scan Button Initiates data capture.
Volume Up/Down Button Increase and decrease audio volume.
Hand Strap Mount Point
Access Door
Provides latching point for the hand strap.
Provides access to microSD card slot and SIM card slot. Optional
2-Pin Access Door is available on device with the SE4710 imager for use with the Trigger Handle.
Provides latching point for the hand strap.
16
Setup
Perform this procedure to start using the TC2X for the first time.
1. Install a micro secure digital (SD) card (optional).
2. Installing a nano SIM card
3. Charge the TC25.
4. Power on the TC25.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the access door.
Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
CAUTION
: Use proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD precau tions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
-
1. Using a 0# Phillips screwdriver, remove two screws securing the access door.
Figure 3 Remove Access Door
2. Remove access door.
17
Figure 4 Remove Access Door
3. Align the microSD card with the SD card slot.
Figure 5 Align microSD Card
4. Push the microSD card into the SD card slot.
Figure 6 Push microSD Card into the SD Card Slot
5. Replace the access Door.
6. Secure the access door using the two screws.
18
Figure 7 Secure Access Door
Installing the SIM Card
NOTE : Only use a nano SIM card.
Only use nano SIM cards that meet the ESTI TS102.221 standard for nano SIM cards, form factor 4FF (0.67 mm thick). Do not use SIM cards that are cut from thicker mini or micro SIM cards.
CAUTION : Use proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
1. Using a 0# Phillips screwdriver, remove two screws securing the access door.
Figure 8 Remove Access Door
2. Align the SIM card with the SIM card slot with the contacts facing down and the cut edge toward the top of the device.
19
Figure 9 Align SIM Card with Slot
3. Push the SIM card in until it locks into the slot.
Figure 10 Push SIM Card into Slot
4. Re-install the access door.
Figure 11 Replace Access Door
Charging the Battery
Before using the TC25 for the first time, charge the internal battery until the green Charging/Notification light emitting diode (LED) remains lit. To charge the TC25 use a USB-C cable or a cradle with the appropriate
20
power supply. For information about the accessories available for the TC25 see Accessories for more
information.
The internal battery charges from fully depleted to 90% in approximately four hours and from fully depleted to
100% in approximately five hours.
NOTE : In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately
10 hours of use.
Use only Zebra charging accessories and batteries. Charge batteries at room temperature with the TC25 in sleep mode.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The TC25 or accessory always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the TC25 or accessory may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The TC25 or accessory indicates when charging is disabled due to abnormal temperatures via its LED and a notification appears on the display.
To charge the main battery:
1. Connect the charging accessory to the appropriate power source.
2. Insert the TC25 into a cradle or attach to a cable. The TC25 turns on and begins charging. The
Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
Figure 12 Charging with Cradle
IMPORTANT : Use only the Zebra USB-C Cable for charging.
21
Figure 13 Charging with USB Cable
Charging Indicators
Table 4 Charging/Notification LED Charging Indicators
State LED
Off
Slow Blinking Amber (1 blink every 4 seconds)
Indication
TC25 is not charging. TC25 is not inserted correctly in the cradle or connected to a power source.
Charger/cradle is not powered.
TC25 is charging.
Slow Blinking Red (1 blink every 4 seconds)
Solid Green
TC25 is charging but the battery is at end of useful life.
See system administrator for battery replacement services.
Charging complete.
Solid Red Charging complete but the battery is at end of useful life. See system administrator for battery replacement services.
22
Table 4 Charging/Notification LED Charging Indicators (Continued)
State
Fast Blinking Amber (2 blinks/second)
LED
Fast Blinking Red (2 blinks/second)
Indication
Charging error, e.g.:
• Temperature is too low or too high.
• Charging has gone on too long without completion
(typically eight hours).
Charging error but the battery is at end of useful life., e.g.:
• Temperature is too low or too high.
• Charging has gone on too long without completion
(typically eight hours).
See system administrator for battery replacement services.
Google Account Setup
NOTE
: The device has to be connected to the internet in order to set up a Google™ account.
A Google account is only required on devices with GMS software.
The first time the device starts, the Setup Wizard displays. Follow the on-screen instructions to set up a Google account, configure Google Pay ™ for purchasing items from the Google Play ™ store, to enter your personal information, and enable backup/restore features.
Zebra Visibility Services
The device captures and provides device analytics to a system administrator. The first time the device boots
(or after a Factory reset), the Zebra Services agreement screen displays.
Figure 14 Zebra Services
Touch the Device Data switch to disable the device from sending analytics data.
23
Replacing the microSD Card
To replace the microSD card:
1. Press the Power button until the menu appears.
2. Touch Power off .
3. Touch OK .
4. If hand strap is attached, remove the hand strap.
5. Using a #0 Phillips screwdriver, remove two screws securing the access door.
6. Remove access door.
Figure 15 Remove Access Door
7. Slide the microSD card out of the SD card slot.
Figure 16 Align microSD Card
8. Lift the microSD card.
9. Align the replacement microSD card with the SD card slot.
24
Figure 17 Align microSD Card
10.Push the microSD card into the SD card slot.
Figure 18 Push microSD Card into the SD Card Slot
11.Replace the access Door.
12.Secure the access door using the two screws.
Figure 19 Secure Access Door
13.Replace the hand strap, if required.
14.Press and hold the Power button to turn on the device.
25
Replacing the SIM Card
NOTE : Only use a nano SIM card.
CAUTION : Access door must be replaced and securely seated to ensure proper device sealing.
TC25 must be powered off when replacing the SIM card.
To replace the SIM card:
1. Press the Power button until the menu appears.
2. Touch Power off .
3. Touch OK .
4. If hand strap is attached, slide the hand strap clip up toward the top of the TC25 and then lift.
5. Using a 0# Phillips screwdriver, remove two screws securing the access door.
Figure 20 Remove Access Door
6. Push the SIM card in to eject the card.
7. Remove the SIM card from the slot.
8. Align the replacement SIM card with the SIM card slot with the contacts facing down and the cut edge toward the top of the device.
Figure 21 Align SIM Card with Slot
26
9. Push the SIM card in until it locks into the slot.
Figure 22 Push SIM Card into Slot
10.Re-install the access door.
Figure 23 Replace Access Door
11.Replace the hand strap, if required.
12.Press and hold the Power button to turn on the TC25.
Accessing Device Settings
To access device settings:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. On the Home screen, swipe up from the bottom of the screen and touch .
Battery Management
NOTE : Prior to checking the battery charge level, remove the device from any AC power source (cradle or cable).
To check the charge status of the main battery, open Settings and touch System > About phone > Battery
Information .
27
Battery present status indicates if the battery is present and Battery level lists the battery charge (as a percentage of fully charged). The battery percentage can also be viewed next to the battery icon in the quick access panel. Swipe down with two fingers from the status bar to open the quick access panel.
Monitoring Battery Usage
The Battery screen provides battery charge details, power management options, and a list of apps that consume the most battery power.
Use the power management options to extend battery life, or touch an app to display details about its power consumption. Different apps display different information. Some apps include buttons that open screens with settings to adjust power use. Use the DISABLE or FORCE CLOSE buttons to turn off apps that consume too much power.
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Battery .
Figure 24 Battery Screen
Low Battery Notification
When the battery charge level drops below 20%, the device displays a notice to connect the device to power.
The user should charge the battery using one of the charging accessories.
When the battery charge drops below 10%, the device displays a notice to connect the device to power. The user must charge the battery using one of the charging accessories.
When the battery charge drops below 4%, the device turns off. The user must charge the battery using one of the charging accessories.
28
Figure 25 Low Battery Notification
Battery Optimization
Observe the following battery saving tips:
• Set the screen to turn off after a short period of non-use.
• Reduce screen brightness.
• Turn off all wireless radios when not in use.
• Turn off automatic syncing for Email, Calendar, Contacts, and other apps.
• Minimize use of apps that keep the device from suspending, for example, music and video apps.
Turning Off the Radios
To turn off all the radios:
1. Press the Power button until the menu appears.
2. Touch Airplane mode . The airplane icon appears in the Status bar indicating that all the radios are off.
Setting the Date and Time
You are only required to set the time zone or set the date and time if the wireless LAN does not support
Network Time Protocol (NTP).
To set the date and time:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch System > Date & time .
3. Touch Automatic date & time to disable automatic date and time synchronization.
4. Touch Set date .
5. In the calendar, set today’s date.
6. Touch OK .
7. Touch Set time .
8. Touch the green circle, drag to the current hour and then release.
9. Touch the green circle, drag to the current minute and then release.
29
10.Touch AM or PM .
11.Touch OK .
12.Touch Use 24-hour format .
13.Touch .
Display Settings
Use Display settings to change the screen brightness, enable night light, change the background image, enable screen rotation, set sleep time, and change font size.
Setting the Screen Brightness
To manually set the screen brightness using the touchscreen:
1. Swipe down with two fingers from the Status bar to open the Quick Access panel.
2. Slide the icon to adjust the screen brightness level.
Figure 26 Brightness Slider
To let the device automatically adjust the screen brightness using the built-in light sensor:
1. Swipe down from the status bar to open the quick settings bar and then touch .
2. Touch Display .
3. If disabled, touch Adaptive brightness to automatically adjust the brightness.
By default, Adaptive brightness is enabled. Toggle the switch to disable.
4. Touch .
Setting Screen Rotation
By default, screen rotation is disabled. To enable screen rotation:
1. Swipe down from the status bar and then touch .
2. Touch Display .
3. Touch When device is rotated and select Rotate to contents of the screen to set the TC25 to automatically switch orientation when the TC25 is rotated.
4. Touch .
Setting Screen Timeout
To set the screen sleep time:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
30
2. Touch Display > Advanced > Sleep .
3. Select one of the sleep values.
• 15 seconds
• 30 seconds
• 1 minute (default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes (default) .
4. Touch .
Setting Font Size
To set the size of the font in system apps:
1. Swipe down from the Status bar to open the Quick Settings panel and then touch .
2. Touch Display > Advanced .
3. Touch Font size .
Figure 27 Font Settings
4. Select one of the font size values.
• Small
• Default
• Large
• Largest.
31
5. Touch .
Setting Screen Rotation
By default, screen rotation is enabled.
To disable screen rotation:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display > Advanced .
3. Touch Auto-rotate screen .
NOTE
: To change the Home screen rotation, see Setting Home Screen Rotation.
4. Touch .
Setting Display Size
By default, display size is set to default.
To change the display size:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Display > Advanced .
3. Touch Display size .
4. Touch - and + to change the display size.
• Small
• Default
5. Touch .
Setting the Charge LED
The user can place the Charging/Notification LED in Standard Mode (default) or Quiet Mode. In Standard
Mode, the Charging/Notification LED is on when the device is charging, and the display is on or off. In Quiet
Mode, Charging/Notification LED is off when the screen is on and the device is charging, and on when the screen is off and the device is charging.
To enable Quiet Mode:
1. Swipe down from the status bar to open the quick access panel and then touch .
2. Touch Display .
3. Touch Charging LED . The option switch turns green.
4. Touch .
32
General Sound Setting
Use the Sound settings to configure media and alarm volumes.
To access sound settings:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Sound .
3. Touch an option to set sounds.
Figure 28 Sound Screen
• Media volume - Controls the music, games, and media volume.
• Alarm volume - Controls the alarm clock volume.
• Ring volume - Controls the ringtone volume.
• Also vibrate for calls - Switch on or off.
• Do Not Disturb preferences - Mutes some or all sounds and vibrations.
• Priority only allows - Use to set the priorities for the following:
• Reminders - Switch on or off.
• Events - Switch on or off.
• Alarms - This is always enabled.
• Messages - Choose to allow messages from anyone, starred contacts, any contact, or none. To star contacts, use the Contacts app.
• Calls - Choose to allow calls from anyone, starred contacts, any contact, or none. To star contacts, use the Contacts app.
• Repeat callers - Choose whether or not the phone rings if the same person calls again within 15 minutes.
• Block visual disturbances
• Block when screen is on - This option prevents notifications from displaying over the screen
(peeking) while you are actively using the device.
• Block when screen is off - This option prevents notifications from turning on the screen or pulsing the LED light when a new notification is received while you are not using the device.
• Automatic rules - Choose when to automatically silence the device. Touch a default rule, such as
Weekend or Weeknight, or create your own rule. To create your own rule, tap Add more and then Time rule .
33
• Phone ringtone - Touch to select a sound to play when the phone rings.
• Advanced - Touch to display advanced sound options.
• Default notification sound - Touch to select a sound to play for all system notifications.
• Default alarm sound - Touch to select a sound to play for alarms.
• Other sounds and vibrations
• Dial pad tones - Play a sound when pressing keys on dial pad (default - disabled).
• Screen locking sounds - Play a sound when locking and unlocking the screen (default – enabled).
• Charging sounds - Not applicable.
• Touch sounds - Play a sound when making screen selections (default – enabled).
• Vibrate on tap - Vibrate the device when making screen selections (default – disabled).
• Emergency alerts - Touch to configure emergency broadcast settings and notifications.
Wake-Up Sources
By default the device wakes from suspend mode when the user presses the power button. The device can be configured to wake when the user presses the PTT on the left side of the device or one of the Scan buttons.
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch System > Wake-Up Sources .
3. Touch one or more of the options:
• Touch Key_PTT checkbox to enable the right scan button. A check appears in the checkbox.
• Touch Key_Scan checkbox to enable the either scan button. A check appears in the checkbox.
Figure 29 Wake-Up Sources
4. Touch .
34
Using the Device
This chapter explains the buttons, status icons, and controls on the device, and provides basic instructions for using the device including resetting the device and entering data.
Google Mobile Services
NOTE : This section applies to Google Mobile Services (GMS) devices only.
Devices with GMS contain apps and services that provide additional functionality.
GMS includes:
• Apps - GMS adds a variety of Google apps and associated widgets including Chrome, Gmail,
Drive, and Maps.
• Services:
• Speech to Text - Allows for free format speech to text in many languages for both connected and disconnected network. Launch by touching the microphone icon on the keyboard.
• TalkBack Service - Provides spoken feedback on various parts of the user interface. To enable, go to Settings > Accessibility .
• Network Location Provider - Adds a location provider which uses mobile network tower information and Wi-Fi access point information to provide a location without using GPS. To enable, go to Settings > Location access .
• Widevine DRM - Enables Digital Rights Management (DRM) so that protected streaming video content can be played. Enable DRM Info from the Google Play ™ store.
• Google Cloud Messaging - Allows the device to receive data from the server and other devices on the same connection.
• Backup and Restore - Allows the users settings and apps to be backed up to a Google server and subsequently restored from that server after a factory reset.
• Google Accounts - Create and use a Google account to synchronize mail, files, music, photos, contacts and calendar events.
Home Screen
Turn on the device to display the Home screen. Depending on the configuration, the Home screen may appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock slider. Touch the screen and slide up to unlock. For screen locking information, see Un-Locking the Screen.
35
The Home screen provides additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
NOTE :
By default, non-GMS devices do not have icons on the Home screen. Icons are shown below for example only.
Home screen icons can be configured by the user and may look different than shown.
Home Screen
1
2
7
8
6
3 4 5
Table 5 Home Screen Items
1 — Status Bar
2 — Widgets
3 — Back
4 — Home
Item
5 — Recent Button
6 — All Apps
7 — Folder
8 — Shortcut Icons
Description
Displays the time, status icons (right side), and notification icons
(left side). For more information see Status Bar on page 37
and
Managing Notifications on page 40
.
Launches stand-alone applications that run on the Home screen.
See App Shortcuts and Widgets on page 43
for more information.
Displays the previous screen.
Displays the Home screen.
Displays recently used applications.
Opens the APPS window.
Contains apps.
Opens applications installed on the device. See App Shortcuts and
Widgets on page 43 for more information.
The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
36
Setting Home Screen Rotation
By default the Home screen rotation is disabled.
To enable Home screen rotation:
1. Touch and hold anywhere on the Home screen until the options appear.
2. Touch HOME SETTINGS .
3. Touch the Allow Home screen rotation switch.
4. Touch .
5. Rotate the device.
Figure 30 Rotated Home Screen
Status Bar
The Status bar displays the time, notification icons (left side), and status icons (right side).
NOTE : Some Status icons may not appear in the Status bar if there are too many icons to display.
Figure 31 Notification and Status Icons
Notification Icons Status Icons
If there are more notifications than can fit in the Status bar, two dots display indicating that more notifications exist. Swipe down from the Status bar to open the Notification panel and view all notifications and status.
Status Icons
Table 6 Status Icons
Icon
Alarm is active.
Main battery is fully charged.
Main battery is partially drained.
Description
Main battery charge is low.
Main battery charge is very low.
1 Cellular network icon that appears is dependent upon the carrier/network.
37
Table 6 Status Icons (Continued)
Icon
Main battery is charging.
Description
All sounds, except media and alarms, are silenced and vibrate mode is active.
Do Not Disturb mode active.
Airplane Mode is active. All radios are turned off.
Bluetooth is on.
The device is connected to a Bluetooth device.
Connected to a Wi-Fi network.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
Portable Wi-Fi hotspot is active.
Connected to a 4G LTE/LTE-CA network 1 .
Connected to a DC-HSPA, HSDPA, HSPA+, HSUPA, LTE/LTE-CA or WCMDMA network 1 .
Connected to a 1x-RTT (Sprint), EGDGE, EVDO, EVDV or WCDMA network 1 .
Connected to a GPRS network 1 .
Connected to a 1x-RTT (Verizon) network 1 .
Roaming from a network.
No SIM card installed.
1 Cellular network icon that appears is dependent upon the carrier/network.
38
Notification Icons
Table 7 Notification Icons
Icon
Main battery is low.
Description
More notifications are available for viewing.
Data is syncing.
Indicates an upcoming event. Non-GMS devices only.
Indicates an upcoming event. GMS devices only.
Open Wi-Fi network is available.
Song is playing.
Problem with sign-in or sync has occurred.
Device is uploading data.
Device is downloading data when animated and download is complete when static.
Device is connected to or disconnected from virtual private network (VPN).
Preparing internal storage by checking it for errors.
USB debugging is enabled on the device.
Call is in progress.
One or more voice message is in mailbox.
Call is on hold.
Call was missed.
Headset is connected to the device.
PTT Express Voice client status. See the PTT Express PTT Notification Icons for a complete list.
Indicates that RxLogger app is running.
Indicates the RS6000 is connected to the device.
Indicates the RS507 or RS6000 is connected to the device in HID mode.
39
Managing Notifications
Notification icons report the arrival of new messages, calendar events, alarms, and ongoing events. When a notification occurs, an icon appears in the Status bar with a brief description. See Notification Icons for a list of possible notification icons and their description. Open the Notification panel to view a list of all the notifications.
To open the Notification panel, drag the Status bar down from the top of the screen.
Figure 32 Notification Panel
To respond to a notification, open the Notification panel and then touch a notification. The Notification panel closes and the corresponding app opens.
To clear all notifications, open the Notification panel and then touch CLEAR ALL . All event-based notifications are removed. Ongoing notifications remain in the list.
To close the Notification panel, swipe the Notification panel up.
Setting App Notifications
To set notification settings for a specific app:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications > App notifications.
3. Select an app.
40
4. Select an available option:
• On / Off - Select to turn all notifications from this app On (default) or Off .
• Allow notification dot - Do not allow this app to add a notification dot to the app icon.
• Allow interruptions - Do not allow notifications from this app to make sound, vibrate, or pop notifications on the screen.
• Override Do Not Disturb - Allow these notifications to interrupt when Do Not Disturb is set to Priority
Only.
• Categories - Do not allow specific types of notifications from this app.
• Additional settings in the app - Open the app settings.
NOTE : To change the notification settings for an app, slide the notification slightly left or right and touch .
Viewing Notification Settings for All Apps
To view the notification settings for all apps:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & Notifications .
3. Scroll down to Notifications to view how many apps have notifications turned off.
4. To set or view notifications settings for a specific app, see Setting App Notifications.
Controlling Lock Screen Notifications
To control whether notifications can be seen when the device is locked:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications .
3. Touch On the lock screen and select one of the following:
• Show all notification content (default)
• Don’t show notifications at all .
Quick Access Panel
Use the Quick Access panel to access frequently used settings (for example, Airplane mode).
Figure 33 Quick Settings Bar
To see the full Quick Access panel:
• If the device is locked, swipe down once.
• If the device is unlocked, swipe down once with two fingers, or twice with one finger.
• If the Quick Settings bar is open, touch the Down arrow.
41
Figure 34 Quick Access Panel
NOTE : Not all icons are pictured. Icons may vary.
To change a setting, touch the icon:
• Display brightness - Use the slider to decrease or increase the brightness of the screen.
• Wi-Fi network - Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
• Bluetooth settings - Turn Bluetooth on or off. To open Bluetooth settings, touch Bluetooth .
• Battery saver - Turn Battery saver mode on or off. When Battery saver mode is on the performance of the device is reduced to preserve battery power.
• Invert colors - Invert the display colors.
• Do not disturb - Control how and when to receive notifications.
• Mobile data - Turns cellular radio on or off. To open Mobile data settings, touch and hold(WAN only).
• Airplane mode - Turn Airplane mode on or off. When Airplane mode is on the device does not connect to
Wi-Fi or Bluetooth.
• Auto-rotate - Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
• Flashlight - Turn flashlight on or off. Turn camera flash on or off.
• Night Light - Tint the screen amber to make it easier to look at the screen in dim light. Set Night Light to turn on automatically from sunset to sunrise, or at other times.
Editing Icons on Quick Settings
The first several setting tiles from the Quick Access panel become the Quick Settings bar.
To move a setting tile:
1. Open the Quick Access panel.
2. Touch .
3. Touch and drag a setting tile to another location.
4. Release the tile.
5. Touch to save tiles and return to the Quick Access panel.
To add a setting tile:
42
1. Open the Quick Access panel.
2. Touch .
3. Slide the Quick Settings panel up to reveal additional tiles.
4. Touch and drag a setting tile from the Drag to add tiles area to the main area.
5. Release the tile.
6. Touch to save tiles and return to Quick Access panel.
To remove a setting tile:
1. Open the Quick Access panel.
2. Touch .
3. Touch and drag a setting tile to the Drag here to remove area.
4. Release the tile.
5. Touch to save tiles and return to Quick Access panel.
App Shortcuts and Widgets
App shortcuts placed on the Home screen allow quick and easy access to apps. Widgets are self-contained apps placed on the Home screen to access frequently used features.
Adding an App Shortcut to the Home Screen
To add an app shortcut to the Home screen:
1. Go to the desired Home screen.
2. Swipe up from the bottom of the screen.
3. Scroll through the list to find the app icon.
4. Touch and hold the icon until the Home screen appears.
5. Position the icon on the screen and then release.
Adding a Widget to the Home Screen
To add a widget to the Home screen:
1. Go to the desired Home screen.
2. Touch and hold until the menu appears.
3. Touch WIDGETS .
4. Scroll through the list to find the widget.
5. Touch and hold the widget until the Home screen appears.
6. Position the widget on the screen and then release.
43
Moving Items on the Home Screen
To move app shortcuts or widgets on the Home screen:
1. Touch and hold the item until it floats on the screen.
2. Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home screen.
3. Lift finger to place the item on the Home screen.
Removing an App Shortcut or Widget from the Home Screen
To remove an app shortcut or widget from the Home screen:
1. Go to the desired Home screen.
2. Touch and hold the app shortcut or widget icon until it floats on the screen.
3. Drag the icon to X Remove at the top of the screen and then release.
Folders
Use Folders to organize similar applications together. Tap the folder to open and display items in the folder.
Creating a Folder
There must be at least two app icons on the Home screen.
To create a folder:
1. Go to the desired Home screen.
2. Touch and hold one app icon.
3. Drag the icon and stack on top of another icon.
4. Lift and release.
Naming Folders
To name a folder:
1. Touch the folder.
Figure 35 Open Folder
Title Area
2. Touch the title area and enter a folder name using the keyboard.
44
3. Touch on the keyboard.
4. Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.
Removing a Folder
To remove a folder:
1. Touch and hold the folder icon until it enlarges.
2. Drag the folder to X Remove and release.
Home Screen Wallpaper
To change the Home screen wallpaper:
1. Touch and hold the screen until the menu appears.
2. Touch WALLPAPERS .
3. Touch Photos or Gallery to select a photo or select one of the pre-installed wallpapers.
4. Touch Set wallpaper .
Using the Touchscreen
Use the multi-tap sensitive screen to operate the device.
• Tap - Tap to:
• Select items on the screen.
• Type letters and symbols using the on-screen keyboard.
• Press on-screen buttons.
• Tap and Hold - Tap and hold:
• An item on the Home screen to move it to a new location or to the trash.
• An item in Apps to create a shortcut on the Home screen.
• The Home screen to open a menu for customizing the Home screen.
• An empty area on the Home screen until the menu appears.
• Drag - Tap and hold an item for a moment and then move finger on the screen until reaching the new position.
• Swipe - Move finger up and down or left and right on the screen to:
• Unlock the screen.
• View additional Home screens.
• View additional app icons in the Launcher window.
• View more information on an app’s screen.
• Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.
• Pinch - In some apps, zoom in and out by placing two fingers on the screen and pinching them together (to zoom out) or spreading them apart (to zoom in).
On-Screen Keyboards
Use the on-screen keyboard to enter text in a text field.
45
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across applications. Some applications do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols and Special Characters
To enter numbers and symbols:
• Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate characters display an ellipsis ( ... ) below the character.
• Touch and hold the Shift key with one finger, touch one or more capital letters or symbols to enter them, and then lift both fingers to return to the lowercase keyboard.
• Touch to switch to the numbers and symbols keyboard.
• Touch the key on the numbers and symbols keyboard to view additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.
• A larger version of the key displays briefly over the keyboard.
• Keys with alternate characters display an ellipsis ( ... ) below the character.
Hiding On-Screen Keyboard
On devices with keypads, the user can hide the on-screen keyboard.
Touch in a text field to display the on-screen keyboard. Touch at the bottom right corner of the screen.
Figure 36 Hide Keyboard Option
Touch the Show virtual keyboard switch to off. The on-screen keyboard automatically disappears.
To show the on-screen keyboard, Touch in a text field. Touch at the bottom right corner of the screen.
Touch the Show virtual keyboard switch to on. The keyboard re-appears.
Switching Language Keyboards
The user can enable multiple language keyboards. The available language codes appear on the space bar.
46
Figure 37 Keyboard with Multiple Languages
To switch between language keyboard, touch at the bottom right corner of the screen.
Figure 38 Change Keyboard Option
Select one of the keyboard languages. The keyboard automatically changes to the selected language.
Configuring the Keyboard
To configure the keyboard, See the Keyboard Settings section in the TC20 Touch Computer Integrator Guide for Android 8.1.0 Oreo.
AOSP Keyboard
To configure the keyboard settings, touch and hold (comma) > and then select Android Keyboard
Settings (AOSP) .
GMS Keyboard
To configure the keyboard settings, touch and hold (comma) > and then select Gboard Keyboard settings.
Do Not Disturb Feature
This mode mutes the device so that it does not make sounds or vibrate.
For example, use Do Not Disturb to:
• Automatically limit sounds at night or during events
• Mute interruptions other than alarms
• Get alerted to messages only from favorite contacts.
Limit Sounds and Vibrations
Mute the device completely, or let through the important alarms or important calls.
47
Total Silence
To completely mute the device so that it does not make a sound or vibrate, choose Total silence .
In Total silence mode:
• Alarms do not make noise.
• Device does not vibrate or make sounds when receiving a message, or notification.
• Sounds from music, videos, games, and other media are muted.
NOTE : All alarms are silenced in Total silence mode.
1. Swipe down with two fingers from the Status bar to open the Quick Access panel.
2. Touch Do not disturb > Total silence .
3. Choose Until you turn it off or select a time period.
4. Touch Done .
When Total Silence is on, appears in the quick access panel and the Status bar.
To turn off Total Silence, open quick access panel and touch Total silence .
Alarms Only
To mute the device so that you hear alarms, choose Alarms only . This option does not mute sounds from music, videos, games, or other media.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Alarms only .
3. Choose Until you turn it off or select a time period.
4. Touch Done .
When Alarms Only is on, appears in the quick access panel and the Status Bar.
To turn off Alarms Only, open the Quick Access panel and touch Alarms only .
NOTE : To quickly turn on Alarms Only, with the screen on, press and hold the Volume Down button until the volume is all the way down. Then, press Volume Down again to turn on Alarms Only.
To turn off Alarms Only, press either the Volume Up or Volume Down button and the touch END NOW in the alert message.
Priority Notifications Only
To only be interrupted by important notifications, choose Priority only . This option does not mute sounds from music, videos, games, or other media.
Before turning on Priority Only mode, set the notification priorities:
1. Swipe down from the status bar to open the quick settings bar and then touch .
2. Touch Sound > Do not disturb > Priority only allows .
48
3. Set priorities.
• Alarms : Disabled by default.
• Reminders and Events : Switch on or off.
• Messages and Calls : Choose From anyone , From contacts only , From starred contacts only , or none . To star contacts, use the Contacts applications.
• Repeat callers : Choose whether to let the device ring if the same person calls again within 15 minutes.
After setting notification priorities, turn on Priority Only mode to limit interruptions. The priority notifications make a sound or vibrate based on the current ringer volume, but other notifications will be silenced.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Priority only .
3. Choose Until you turn it off or select a time period.
4. Tap Done .
When Priority Only is on, appears in the quick access panel and the Status Bar.
To turn off Priority Only, open quick access panel and touch Priority only .
Automatically Block Sounds and Vibrations
Automatically silence the device during certain times or events, turn sounds back on, and override Do Not
Disturb mode.
Silence Sounds During Certain Times
To automatically silence the device during certain times, like at night or on weekends:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Sound > Do Not Disturb preferences .
3. Touch a default Weekend or Weeknight . Or, to make a new rule, touch Add more > Time rule .
4. Enter a rule name.
5. Touch OK .
6. Edit the new rule:
• Rule name - Rename the rule.
• Days , Start time , and End time - Set the rule's schedule.
• Do Not Disturb preferences - Choose whether the rule uses Alarms only , Priority only , or Total silence.
• Alarm can override end time - Allow the alarm to continue to make sound until the next alarm begins.
7. Touch the On/Off switch at the top to turn on the rule.
Silence Sounds During Events and Meetings
To automatically silence the device during events or meetings, set an event rules.
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
49
2. Touch Sound > Do Not Disturb preferences .
3. To edit the default rule, touch Event . Or, to create a new rule, touch Add rule > Event rule .
4. Edit the rule settings.
• Rule name - Rename the rule.
• During events for - Select which Google Calendar events the rule uses.
• Where reply is - Set to: Yes, Maybe, or Not replied , Yes or Maybe , or Yes .
• Do Not Disturb preferences - Choose whether the rule uses Priority only , Alarms only , or Total silence .
5. Touch the On/Off switch at the top to turn on the rule.
Turn Sounds Back On
When the device is in Do Not Disturb mode, Alarms only or Priority only display as , or Total silence displays as .
To turn off Do Not Disturb, either:
• In the Quick Access panel, touch Alarms only , Priority only , or Total silence .
• Press the Volume Down button and touch End Now .
Override Do Not Disturb for Specific Apps
To let through notifications from specific apps:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Apps & notifications > Notifications > App notifications .
3. Touch an app.
4. Touch Override Do Not Disturb .
50
Apps
The APPS screen displays icons for all installed apps. The table below lists the apps installed on the device.
Refer to the device Integrator Guide for Android Version 8.1 for information on installing and uninstalling apps.
Table 8 Apps
Icon Description
Bluetooth Pairing Utility – Use to pair the RS507 Hands-free Imager with the device by scanning a barcode.
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments. GMS devices only
Calendar - Use to manage events and appointments. Non-GMS devices only.
Camera - Take photos or record videos. For more information see Camera.
Chrome - Use to access the Internet or intranet. GMS devices only
Chromium - Use to access the Internet or intranet. Non-GMS devices only.
Clock - Use to schedule alarms for appointments or as a wake-up.
Contacts - Use to manage contact information. See Contacts for more information.
DataWedge - Enables data capture using the imager.
Diagnostic Tool - Use to diagnose the device.
Drive - Upload photos, videos, documents, and other files to personal storage site. GMS devices only
Duo - A one-to-one video calling app.
51
Table 8 Apps (Continued)
Icon Description
DWDemo - Provides a way to demonstrate the data capture features using the imager. See
DataWedge Demonstration for more information.
Email - Use to send and receive email. Non-GMS devices only.
Files - Organize and manage files on the device. See Files for more information.
Gallery - Use to view photos stored on the microSD card. For more information, see Gallery for more information. Non-GMS devices only.
Gmail - Use to send and receive email using a Google email account. GMS devices only
Google - Launches Google ™ search app. GMS devices only
Hangouts - Use to communicate with friends using text messages and photos. GMS devices only
Install ATL - Use to download and install the Asset Tracker Lite application from the Zebra
Support site. For information on Asset Tracker Lite application, refer to the Asset Tracker Lite
User Guide.
License Manager - Use to manage software licenses on the device.
Maps - Use to see your location on a map (with public transit, traffic, or satellite overlays).
Search for any business or place of interest. Provides turn-by-turn navigation with voice guidance, traffic-avoidance, and alternate routes, for drivers, cyclists, walkers, and users of public transportation. GMS devices only
Messaging - Send SMS and MMS messages. See Messaging for more information. WAN devices only.
Phone - Use to dial a phone number when used with some Voice over IP (VoIP) clients (VoIP telephony ready only). WAN devices only.
Photos - Use to sync photos with Google account. For more information, see Photo Settings.
GMS devices only
Play Movies & TV - View movies and video on your device. GMS devices only
52
Table 8 Apps (Continued)
Icon Description
Play Music - Use to listen to music. GMS devices only
Play Store - Download music, movies, books, and Android apps and games from the Google
Play Store. GMS devices only
PTT Express - Use to launch PTT Express client for VoIP communication.
RxLogger - Use to diagnose device and app issues. See the device Integrator Guide for
Android Version 8.1 for more information.
RxLogger Utility - Use to view, backup, and archive RxLogger data.
Search - Use to search the Web. Requires an Internet connection. Non-GMS devices only.
Settings - Use to configure the device.
Sound Recorder - Use to record audio.
StageNow - Allows the device to stage a device for initial use by initiating the deployment of settings, firmware, and software.
User Guide Download - Use to download and install User Guide apk.
Videos - Use to view videos on the device. Non-GMS devices only.
Voice Search - Use to perform searches by asking questions. GMS devices only
YouTube - Use to view videos on the YouTube ™ web site. GMS devices only
Accessing Apps
All apps installed on the device are accessed using the APPS window.
53
1. On the Home screen, swipe up from the bottom of the screen.
Figure 39 APPS Window Example
Slide the APPS window up or down to view more app icons. Touch an icon to open the app.
Switching Between Recent Apps
To switch between recent apps:
1. Touch . A window appears on the screen with icons of recently used apps.
1
Figure 40 Recently Used Apps
2. Slide the apps displayed up and down to view all recently used apps.
54
3. Swipe left or right to remove app from the list and force close the app.
4. Touch an icon to open an app or touch to return to the current screen.
Un-Locking the Screen
Use the Lock screen to protect access to data on the device. Some email accounts require locking the screen.
Refer to the device Integrator Guide for information on setting up the locking feature.
When locked, a pattern, PIN, or password is required to unlock the device. Press the Power button to lock the screen. The device also locks after a pre-defined time-out.
Press and release the Power button to wake the device. The Lock screen displays. Swipe the screen up to unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
Figure 41 Lock Screen
55
Figure 42 PIN Screen
Figure 43 Pattern Screen
56
Figure 44 Password Screen
Resetting the Device
There are two reset functions, soft reset and hard reset.
Performing a Soft Reset
Perform a soft reset if applications stop responding.
1. Press and hold the Power button until the menu appears.
2. Touch Reset .
3. The device reboots.
Performing a Hard Reset
CAUTION : Performing a hard reset with a microSD card installed in the device may cause damage or data corruption to the microSD card.
Perform a hard reset if the device stops responding.
1. Simultaneously press the Power and Volume Up buttons for at least five seconds.
2. When the screen turns off, release the buttons.
3. The device reboots.
57
Suspend Mode
The device goes into suspend mode when the user presses the Power button or after a period of inactivity (set in the Display settings window).
To wake the device from Suspend mode, press the Power button. The Lock screen displays. Swipe the screen up to unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
NOTE : If the user enters the PIN, password or pattern incorrectly five times, they must wait 30 seconds before trying again.
If the user forgets the PIN, password or pattern contact the system administrator.
Transferring Files with a Host Computer via USB
Connect the device to a host computer using a USB cable or a USB cradle to transfer files between the device and the host computer.
When connecting the device to a host computer, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
Transferring Files
NOTE
: Use Transfer files to copy files between the device (internal memory or microSD card) and the host computer.
1. Connect a USB cable to the device or place the device into a USB cradle.
2. Pull down the Notification panel and touch USB charging this device .
By default, Charge this device is selected.
Figure 45 Use USB to Dialog Box
3. Touch Transfer files .
4. On the host computer, open a file explorer application.
5. Locate the device as a portable device.
6. Open the SD card or the Internal storage folder.
7. Copy files to and from the device or delete files as required.
58
Transferring Photos
To transfer photos using Photo Transfer Protocol:
NOTE puter.
: Use Photo Transfer Protocol (PTP) to copy photos from either the microSD card or internal memory to the host com -
1. Connect USB cable to the device or place the device into a USB cradle. See
for setup information.
2. Pull down the Notification panel and touch USB charging this device .
3. Touch Transfer photos (PTP) .
4. On the host computer, open a file explorer application.
5. Open the SD card or the Internal storage folder.
6. Copy or delete photos as required.
Disconnect from the Host Computer
To disconnect the device from the host computer:
CAUTION : Carefully follow the host computer’s instructions to unmount the microSD card and disconnect USB devices cor rectly to avoid losing information.
-
1. On the host computer, unmount the device.
2. Remove the USB from the device or remove the device from the cradle.
59
Calls
Introduction
Make a phone call from the Phone app, the Contacts app, or other apps or widgets that display contact information. This section applies to WWAN devices only.
Emergency Calling
The service provider programs one or more emergency phone numbers, such as 911 or 999, that the user can call under any circumstances, even when the phone is locked, a SIM card is not inserted or the phone is not activated. The service provider can program additional emergency numbers into the SIM card. However, the
SIM card must be inserted in the device in order to use the numbers stored on it. See the service provider for additional information.
NOTE : Emergency numbers vary by country. The phone’s pre-programmed emergency number(s) may not work in all loca tions, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues.
-
Audio Modes
The device offers three audio modes for use during phone calls:
• Handset Mode - Switch audio to the receiver at the top front of the device to use the device as a handset.
This is the default mode.
• Speaker Mode - Use the device as a speakerphone.
• Headset Mode - Connect a Bluetooth or wired headset to automatically switch audio to the headset.
Using a Bluetooth Headset
for information on connecting a Bluetooth headset to the device. Set the volume appropriately before putting on the headset. When a Bluetooth headset is connected, the speakerphone is muted.
Adjusting Audio Volume
Use the volume buttons to adjust the phone volume in the following ways:
• Ring and notification volumes when not in a call
• Conversation volume during a call.
60
Making a Call Using the Dialer
Use the dialer tab to dial phone numbers.
1. On the Home screen touch .
2. Touch .
Figure 46 Dialer Screen
3. Touch the keys to enter the phone number.
4. Touch below the dialer to initiate the call.
Figure 47 Call in Progress
61
•
•
•
•
•
•
- Send audio to the speakerphone.
- Mute the call.
- Display the dial pad.
- Place the call on hold (not available on all services).
- Create a conference call.
- Increase audio level.
5. Touch to end the call.
If using a Bluetooth headset, additional audio options are available. Touch the audio icon to open the audio menu.
Figure 48 Bluetooth Audio Options
•
•
• - Audio is routed to the Bluetooth headset.
- Audio is routed to the speakerphone.
- Audio is routed to the earpiece.
Dialer Dialing Options
The dialer provides options to save the dialed number to contacts, send an SMS, or insert pauses and wait into the dial string.
Enter at least one digit to access these options. Touch to access the following.
• Add 2–sec pause - Pause the dialing of the next number for two seconds. Multiple pauses are added sequentially.
• Add wait - Wait for confirmation to send the rest of the digits.
Making a Call Using Contacts
There are two ways to make a call using contacts:
62
• Using the Dialer
• Using the Contacts app.
Using the Dialer
1. On the Home screen touch .
2. Touch the tab.
Figure 49 Dialer Contacts Tab
3. Touch the contact.
4. Touch to initiate the call.
5. Touch to end the call.
Using the Contacts App
To make a call from the Contacts app:
63
1. Touch .
Figure 50 Contact app
2. Touch a contact name.
Figure 51 Contact Information
3. Touch to initiate a call.
64
Making a Conference Call on GSM
To create a conference phone session with multiple people.
NOTE : Conference Calling and the number of conference calls allowed may not be available on all services. Please check with the service provider for Conference Calling availability.
1. On the Home screen touch .
2. Touch .
3. Touch the keys to enter the phone number.
4. Touch below the dialer to initiate the call.
5. When the call connects, touch .
The first call is placed on hold.
6. Touch .
7. Touch the keys to enter the second phone number.
8. Touch below the dialer to initiate the call.
9. When the call connects, the first call is placed on hold and the second call is active.
Figure 52 Two Calls
65
10.Touch icon to create a conference call with three people.
Figure 53 Merged Calls
11.Touch to add another call.
The conference is placed on hold.
12.Touch .
13.Touch the keys to enter another phone number.
14.Touch below the dialer to initiate the call.
15.Touch icon to add the third call to the conference.
66
16.Touch Manage to view all callers.
Figure 54 Un-merge Calls
17.To remove a caller from the conference, touch next to the caller.
To speak privately with one party during a conference call, touch . To include all parties again, touch .
Making a Conference Call on GSM
To create a conference phone session with multiple people.
NOTE
: Conference Calling and the number of conference calls allowed may not be available on all services. Please check with the service provider for Conference Calling availability.
1. On the Home screen touch .
2. Touch .
3. Touch the keys to enter the phone number.
4. Touch below the dialer to initiate the call.
5. When the call connects, touch .
The first call is placed on hold.
6. Touch .
7. Touch the keys to enter the second phone number.
8. Touch below the dialer to initiate the call.
67
9. When the call connects, the first call is placed on hold and the second call is active.
Figure 55 Two Calls
68
10.Touch icon to create a conference call with three people.
Figure 56 Merged Calls
11.Touch to add another call.
The conference is placed on hold.
12.Touch .
13.Touch the keys to enter another phone number.
14.Touch below the dialer to initiate the call.
15.Touch icon to add the third call to the conference.
69
16.Touch Manage to view all callers.
Figure 57 Un-merge Calls
17.To remove a caller from the conference, touch next to the caller.
To speak privately with one party during a conference call, touch . To include all parties again, touch .
Making a Call Using a Bluetooth Headset
To make a call using a Bluetooth headset:
1. Pair the Bluetooth headset with the device.
2. Press the Call button on the Bluetooth headset.
3. Press the Call button on the Bluetooth headset to end the call.
Answering Calls
When receiving a phone call, the Incoming Call screen displays the caller ID and any additional information about the caller that is in the Contacts app.
Figure 58 Incoming Call Screen
70
Touch ANSWER to answer the call or DECLINE to send the caller to voice mail.
If the screen lock is enabled, the user can answer the call without unlocking the device.
Figure 59 Incoming Call Locked Screen
When a call arrives:
• Touch and slide up to answer the call.
• Touch and slide down to send the call to voice mail.
• Touch to open a list of quick text responses. Touch one to send it to the caller immediately.
When the calls ends, the device remains locked.
If using a Bluetooth headset when a call arrives, touch the Call button on the Bluetooth headset to answer the call. To end the call press the headset Call button.
All incoming calls are recorded in the Phone app Call log tab. If you miss a call, you receive a notification. To silence the ringer before answering the call, press the volume down button on the side of device.
Call Settings
NOTE : Not all options are available for all configurations
To modify phone call settings, on the Home screen touch > > Settings .
• Display options
• Sort by - Set to First name or Last name .
• Name format - Set to First name first or Last name first .
71
• Sounds and vibrations
• Phone ringtone - Select a ringtone to sound when an incoming call is received.
• Also vibrate for calls - Check to make the device vibrate when a call is received (default - disabled).
• keypad tones - Check to play a sound when a phone key is touched (default - enabled).
• keypad tone length - Set the tone length to Normal (default) or Long .
• Quick responses - Touch to edit quick responses to use instead of answering a call.
• Speed dial settings - Set speed dial contact shortcuts.
• Calls
• Calling accounts
• Receive incoming calls - Enable to allow incoming calls (default - disabled).
• Call forwarding - Set to forward incoming calls to a different phone number.
NOTE : Call Forwarding may not be available on all networks. Check with the service provider for availability.
• Additional settings
• Caller ID - Set caller ID to reveal the identity of the person making an outgoing call. Options:
Network default (default), Hide number , Show number .
• Call blocking - Set to block calls and texts from certain phone numbers. Touch ADD A NUMBER to block a phone number.
• Voicemail - Configure voicemail settings.
• Notifications
• Importance - Set the notification importance to Urgent , High (default), Medium , or Low.
• Sound - Select a sound to play when a voicemail is received.
• Vibrate - Set vibrate to On (default) or Off .
• Advanced - Use toggle switches to enable or disable Blink link , Show notification , or Override Do
Not Disturb. Available options vary depending on the Importance setting.
• Advanced Settings
• Service - Set the service provider or other provider for voicemail service.
• Setup - Select to update the phone number used to access voicemail.
• Accessibility
• TTY mode - Touch to set the TTY setting. Use an optional teletypewriter (TTY) with the device to send and receive calls. Plug the TTY into the device headset jack and set the device to operate in one of the
TTY modes.
NOTE : Use a TSB-121 compliant cable (provided by the TTY manufacturer) to connect the TTY to the device.
Set the device volume to a middle level setting for proper operation. If you experience a high number of incorrect characters, adjust the volume as needed to minimize the error rate.
For optimal performance, the device should be at least 30 cm (12 inches) from the TTY. Placing the device too close to the TTY may cause high error rates.
• TTY off - TTY is off (default)
• TTY Full - Transmit and receive TTY characters
• TTY HCO - Transmit TTY characters, but receive by listening to earpiece
• TTY VCO - Receive TTY characters, but transmit by speaking into microphone.
72
Applications
This section describes the applications installed on the device.
73
Applications
Camera
This section provides information for taking photos and recording videos using the integrated digital cameras.
NOTE : The device saves photos and videos on the microSD card, if installed and the storage path is changed manually. By default, or if a microSD card is not installed, the device saves photos and videos on the internal storage.
Taking Photos
NOTE : See Photo Settings for camera setting descriptions.
1. Swipe up from the bottom of the Home screen and touch Camera .
Figure 60 Camera Mode
Color Effect High Dynamic Range
Scene Mode Settings
Gallery Camera Mode
Shutter Button
2. If necessary, touch the Camera Mode icon and touch .
3. Frame the subject on the screen.
4. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
74
Applications
5. Touch an area on the screen to focus. The focus circle appears. The two bars turn green when in focus.
6. Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
Taking a Panoramic Photo
Panorama mode creates a single wide image by panning slowly across a scene.
1. Swipe up from the bottom of the Home screen and touch Camera .
Figure 61 Panoramic Mode
2. Touch the Camera Mode icon and touch .
3. Frame one side of the scene to capture.
4. Touch and slowly pan across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If you are panning too quickly, the message Too fast appears.
5. Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
Recording Videos
1. Swipe up from the bottom of the Home screen and touch Camera .
75
Applications
2. Touch the camera mode menu and touch .
Figure 62 Video Mode
Color Effect Audio
Settings
Gallery Camera Mode
Shutter Button
3. Point the camera and frame the scene.
4. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
5. Touch to start recording.
The video time remaining appears in the top left of the screen.
6. Touch to the end recording.
The video momentarily displays as a thumbnail in the lower left corner.
Photo Settings
In Photo mode, photo settings appear on screen. Touch to display the photo settings options.
76
Applications
Rear Camera
• Flash - Select whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
• Off - Disable flash.
Auto - Adjust flash automatically depending upon light meter (default).
• On - Enable flash upon taking a photo.
• GPS location - Turn On or Off (default).
• Picture size - The size (in pixels) of the photo to: 8M pixels (default), 5M pixels , 4M pixels (16:9) , 3M pixels , HD 1080 , 2M pixels , 1.5M pixels , 1.3M pixels , WXGA , HD720 , 1M pixels , SVGA , WVGA , 720 x
480 , VGA, CIF , or QVGA .
• Picture quality - Set the picture quality setting to: Low , Standard (default) or High .
• Countdown timer - Select Off (default), 2 seconds , 5 seconds or 10 seconds .
• Storage – Set the location to store the photo to: Phone or SD Card .
• Continuous Shot - Select to take a series of photos quickly while holding the capture button. Off (default) or On .
• Face Detection - Select to turn face detection Off (default) or On .
• ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled).
• Anti Banding - Select to prevent the appearance of vertical or horizontal lines (banding) when photographing images on TV and monitor screens. Options: Off (default), 50 Hz , 60 Hz , or Auto .
• ISO - Set camera sensitivity to light to: Auto (default), ISO Auto (HJR) , ISO100 , ISO200 , ISO400 , ISO800 or ISO1600 .
• Exposure - Set the exposure settings to: +2 , +1 , 0 (default), -1 or -2 .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
•
•
•
• Incandescent
Fluorescent
Auto
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Chroma Flash - Sets the camera to take two pictures, one with flash and one without flash. The two images are combined to produce a final image with the sharpness and clarity and bright color tones from a picture with the flash, coupled with the natural colors of a picture without a flash. Options: Off (default) or
On .
• Redeye reduction - Helps eliminate redeye effect. Options: Disabled (default), or Enable .
• Shutter Sound - Select to play a shutter sound when taking a photo. Options: Disable (default) or Enable .
Video Settings
In Video mode, video settings appear on screen. Touch to display the video settings options.
77
Applications
Rear Camera
• Flash - Select whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
• Off - Disable flash (default).
• Torch - Turn flash on continuously.
• Video quality - Set video quality to: HD 1080p (default), HD 720p , SD 480p, VGA, CIF, or QVGA .
• Video duration - Set to: 10 minutes (default), 30 minutes , or no limit .
• Storage – Set the location to store the photo to: Phone (default) or SD Card .
• White balance - Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
•
•
• Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
Auto - Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Video High FrameRate - Select a high frame rate for videos to capture movement more clearly. Options:
Off (default), HFR 60 , HFR 90 , HFR 120 , HSR 60 , HSR 90 , or HSR 120 .
• Image Stabilization - Set to reduce blurry videos due to device movement. Options: On or Off (default).
Contacts
Use the Contacts app to manage contacts.
From a Home or Apps screen, touch Contacts to open to the main list of contacts. Contacts are listed in alphabetical order. Swipe up or down to scroll through the list.
Adding a Contact
1. In the Contacts app, touch .
2. If there is more than one account with contacts, touch the one you want to use.
3. Type the contact’s name and other information. Touch a field to start typing, and swipe down to view all categories.
4. To open a menu with preset labels, such as Home or Work for an email address, touch the label to the right of the item of contact information. Or, to create your own label, touch Custom in the menu.
5. Touch the check mark next to Add New Contact .
Editing Contacts
1. In the Contacts app, touch a contact name to edit.
2. Touch .
78
Applications
3. Edit the contact information.
4. Touch SAVE .
Deleting Contacts
1. In the Contacts app, touch a contact name to delete.
2. Touch .
3. Touch Delete .
4. Touch DELETE to confirm.
79
Applications
DataWedge Demonstration
NOTE : DataWedge is enabled on the Home screen.To disable this feature, go to the DataWedge settings and disable the
Launcher profile.
Use DataWedge Demonstration to demonstrate data capture functionality.
Figure 63 DataWedge Demonstration Window
Table 9 DataWedge Demonstration Icons
Icon
Illumination
Description
Imager illumination is on. Touch to turn illumination off.
Imager illumination is off. Touch to turn illumination on.
Data Capture The data capture function is through the internal imager.
An RS507 or RS6000 Bluetooth imager is connected.
An RS507 or RS6000 Bluetooth imager is not connected.
80
Applications
Table 9 DataWedge Demonstration Icons (Continued)
Icon
Scan Mode
Description
Imager is in picklist mode. Touch to change to normal scan mode.
Imager is in normal scan mode. Touch to change to picklist mode.
Opens a menu to view the application information or to set the application DataWedge profile.
NOTE : See the device Integrator Guide for Android Version 8.1 for information on DataWedge configuration.
Scanner Selection
To select a scanner, touch > Settings > Scanner selection .
See Data Capture for more information.
Either press the programmable button or touch the yellow scan button to capture data. The data appears in the text field below the yellow button.
Diagnostic Tool
The Diagnostic Tool is a utility that determines the health of the device. Use the Diagnostic Tool to troubleshoot the device.
1. Swipe up from the bottom of the Home screen and touch .
Figure 64 Diagnostic Tool
81
Applications
2. Touch RUN TEST . The app tests all enabled subsystems (by default, only the Battery and System tests).
See Settings to enable subsystem tests.
Figure 65 Test Passed Screen
Figure 66 Test Failed Screen
3. To view each subsystem test, touch Subsystem Tests .
82
Figure 67 Subsystem Screen
Applications
4. Touch one of the subsystems to view details.
Table 10 Subsystem Test Result Indicators
Status Icon Description
Test passed.
Test failed.
Test not supported or not enabled.
83
Figure 68 Battery Subsystem Details
Applications
Settings
By default only the Battery and System tests are enabled. To enable other tests:
1. Touch > Settings .
2. Touch to the left of the test name. A green box with a checkmark appears.
3. Touch SAVE .
4. Touch Yes to confirm.
5. Touch .
Battery Test Information
The Battery Test obtains the following information:
• Battery Level - Current battery charge level
• Battery Voltage - Current battery voltage
• Status - Whether the battery is charging (on AC power) or discharging (on battery power)
• Power Source - Whether the device is receiving power from the battery or from an external source
• Temperature - Current battery temperature
• Health Percentage - Indicates the ratio of present capacity to design capacity at a discharge rate of design capacity.
• Backup Battery Voltage - Backup battery voltage.
• Manufacture Date - Manufacture date of the battery.
84
Applications
GPS Test Information
The GPS Test obtains the following information (WWAN only):
• GPS Provider Enabled - Whether GPS is enabled (true) or disabled (false)
• Latitude - Current latitude position
• Longitude - Current longitude position
• Altitude - Current altitude in meters
• Bearing - Current bearing
• Speed - Speed in meters per second
• Accuracy - GPS accuracy in meters.
System Test Information
Use the System Test to determine if the CPU or memory loads are too high, there are too many processes running on the device, or storage on the device is almost full.
The System Test obtains the following information:
• CPU Load - Amount of CPU being used
• Free Physical Memory - Amount of RAM available
• Free Storage - Amount of internal Flash memory available
• Process Count - Number of processes currently running.
WLAN Test Information
If the WiFi radio is not present or disabled, skip this test. This test determines if the device’s WLAN configuration is correct or whether there is any connection with an access point or network.
The WLAN test obtains the following information:
• WLAN Enabled - WLAN radio is enabled or disabled
• WLAN Status - Current status of association with the access point
• ESSID - Name of the wireless network
• BSSID - MAC address of the connected access point
• MAC Address - Device’s MAC address
• Signal - Strength of the Wi-Fi signal (in dBm)
• IP Address - IP address of the device.
WWAN Test Information
The WWAN Test obtains the following information (WWAN only):
• SIM State - Current state of the SIM card
• WAN Type - Data connection type
• Signal Strength - Current cellular signal strength
• Phone Number - Phone number assigned to the device
85
Applications
• Device ID - Device ID number.
Bluetooth Test Information
The Bluetooth Test obtains the following information:
• Enabled - Whether the Bluetooth radio is enabled or disabled
• Status - Whether the device is paired to another Bluetooth device
• Connectable/Discoverable - Whether the device is discoverable or able to connect
• Address - Bluetooth radio MAC address
• Name - Bluetooth name for the device.
86
Applications
Files
Use the Files app to view and manage files on the device.
To open Files , swipe up from the bottom of the screen and touch .
Figure 69 Files Screen
Sort
•
•
• Touch and hold an item to open the File Operations menu. Select an option:
•
•
•
• - Share the file with other devices.
- Delete the file.
• - View additional options.
• Open with - Select which app is used to open the file.
• Select all - Select all folders and files.
• Copy to...
- Copy the file.
• Move to...
- Move the file or folder to a new location.
• Compress - Compress the selected file(s) into a ZIP file.
• Rename - Rename the file.
• Touch the Sort drop-down to sort files by name, type, size, or date.
- View all file locations.
- Search for a specific file on the device.
/ - Change the folder to display items as a list / grid.
- Open the options menu.
• New Window - Create a new Files window.
• New Folder - Create a new folder.
• Select all - Select all folders and files.
• Show/Hide internal storage - Show or hide internal storage.
87
Applications
Gallery
NOTE : The device supports the following image formats: jpeg, gif, png and bmp.
The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Available on device with AOSP only.
Use Gallery to:
• View photos
• Play videos
• Perform basic editing of photos
• Set photos as wallpaper
• Set photos as a contact photo
• Share photos and videos.
Gallery presents all photos and videos stored on the microSD card and internal memory.
To open Gallery , swipe up from the bottom of the Home screen and touch Gallery , or in the camera app touch the thumbnail image at the bottom left.
By default, Gallery opens to the Timeline view.
Figure 70 Gallery - Timeline View
Touch > Albums to view photos sorted by albums or > Videos to view only videos.
88
Figure 71 Gallery — Albums View
Applications
• Touch an album to open it and view its contents. The photos and videos in the album are displayed in chronological order.
• Touch a photo or video in an album to view it.
• Touch > Timeline to return to the default Gallery screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in a chronologically ordered grid. The name of the album displays at the top of the screen.
89
Figure 72 Photos Inside an Album
Applications
Swipe up or down to scroll through the images.
Sharing an Album
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch and hold an album to highlight it.
3. Touch other albums as required.
4. Touch . The Share menu opens.
5. Touch the app to use to share the selected albums.
6. Follow the instructions within the selected app.
Getting Album Information
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch and hold an album to highlight it.
3. Touch .
4. Touch Details .
Deleting an Album
To delete an album and its contents:
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch and hold an album to highlight it.
3. Check other albums to delete.
90
Applications
4. Touch .
5. In the Delete selected item?
menu, touch OK to delete the album.
Working with Photos
Use Gallery to view photos on the device and edit and share photos.
Cropping a Photo
1. In Gallery , touch a photo to view the controls.
2. Touch > > . The cropping tool appears.
3. Use the cropping tool to select the portion of the photo to crop.
• Drag from the inside of the cropping tool to move it.
• Drag an edge of the cropping tool to resize it to any proportion.
Figure 73 Cropping Tool
4. Touch > SAVE to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch Set picture as .
91
Applications
6. Touch Contact photo .
7. In Contacts , touch a contact.
8. Touch the white box and crop the photo accordingly.
9. Touch SAVE .
Sharing a Photo
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch the app to use to share the selected photo.
6. Follow the instructions within the selected app.
Deleting a Photo
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch OK to delete the photo.
Working with Videos
Use Gallery to view and share videos.
Watching Videos
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch an album to open it.
3. Touch a video.
4. Touch to play.
5. Touch the screen to view the playback controls.
Sharing a Video
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch an album to open it.
3. Touch a video to open it.
4. Touch . The Share menu appears.
5. Touch the app to use to share the selected video.
92
Applications
6. Follow the instructions within the selected app.
Deleting a Video
1. Swipe up from the bottom of the Home screen and touch Gallery .
2. Touch an album to open it.
3. Touch a video to open it.
4. Touch .
5. Touch OK .
93
Applications
Photos
NOTE : The device supports the following image formats: jpeg, gif, png, and bmp.
The device supports the following video formats: H.263, H.264
, and MPEG4 Simple Profile.
Available on device with GMS only.
Use Photos to:
• View photos
• Play videos
• Perform basic editing of photos
• Set photos as wallpaper
• Set photos as a contact photo
• Share photos and videos.
Photos presents all photos and videos stored on the microSD card and internal memory.
To open Photos , swipe up from the bottom of the Home screen and touch Photos .
By default, Photos opens to the photos view.
Figure 74 Photos View
Touch Albums to view photos sorted by albums.
94
Figure 75 Albums View
Applications
• Touch an album to view its contents. The photos and videos in the album appear in chronological order.
• Touch a photo or video in an album to view it.
• Touch to return to the main screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in a chronologically ordered grid. The name of the album displays at the top of the screen.
95
Figure 76 Photos Inside an Album
Applications
Swipe up to scroll through the images.
Deleting an Album
To delete an album and its contents:
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch Albums .
3. Touch an album.
4. Touch > Select .
5. Select all photos in the album.
6. Touch .
7. Touch Move to trash to delete the album.
Working with Photos
Use Photos to view photos on the internal memory and the microSD card.
Viewing and Browsing Photos
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch a photo.
Figure 77 Photo Example
96
Applications
3. Swipe left or right to view the next or previous photo in the album.
4. Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is displayed (but not saved) in the new orientation.
5. Touch the photo to view the controls.
6. Double-tap the screen to zoom in, or pinch two fingers together or spread them apart to zoom in or out.
7. Drag the photo to view parts that are not in view.
Cropping a Photo
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch a photo to view the controls.
3. Touch > . The cropping tool appears.
Figure 78 Cropping Tool
97
Applications
4. Use the cropping tool to select the portion of the photo to crop.
• Drag from the inside of the cropping area to move it.
• Drag an edge of the cropping area to resize it to any proportion.
5. Touch DONE.
6. Touch SAVE to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch the photo to open it.
3. Touch > Use as .
4. Touch Contact photo .
5. In the Contacts app, touch a contact.
6. Touch the white box and crop the photo accordingly.
7. Touch Done .
Sharing a Photo
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
98
Applications
5. Touch the app to use to share the selected photo.
6. Follow the instructions within the selected app.
Deleting a Photo
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch a photo to open it.
3. Touch .
4. Touch MOVE TO TRASH .
Working with Videos
Use Photos to view and share videos.
Watching a Video
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch a video to play.
3. Touch the screen to view the playback controls.
Sharing a Video
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch a video to open it.
3. Touch . The Share menu appears.
4. Touch the app to use to share the selected video.
5. Follow the instructions within the selected app.
Deleting a Video
1. Swipe up from the bottom of the Home screen and touch Photos .
2. Touch a video to open it.
3. Touch .
4. Touch MOVE TO TRASH to delete the video.
99
Applications
PTT Express Voice Client
NOTE : PTT Express Voice Client enables Push-To-Talk (PTT) communication between disparate enterprise devices. Le veraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple PTT communication without requiring voice communication server.
-
• Group Call : Press and hold the PTT (Talk) button to start communicating with other voice client users.
• Private Response : Double-press the PTT button to respond to the originator of the last broadcast or to make a Private Response.
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
• Talk Tone : Double chirp. Plays when the Talk button is depressed. This is a prompt for you to start talking.
• Access Tone : Single beep. Plays when another user just finished a broadcast or response. You can now initiate a Group Broadcast or Private Response.
• Busy Tone : Continuous tone. Plays when the Talk button is depressed and another user is already communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).
• Network Tone :
• Three increasing pitch beeps. Plays when PTT Express acquires the WLAN connection and the service is enabled.
• Three decreasing pitch beeps. Plays when PTT Express loses the WLAN connection or the service is disabled.
PTT Notification Icons
Notification icons indicate the current state of the PTT Express Voice client.
Table 11 PTT Express Icon Descriptions
Status Icon Description
The PTT Express Voice client is disabled.
The PTT Express Voice client is enabled but not connected to a WLAN.
The PTT Express Voice client is enabled, connected to a WLAN, and listening on the Talk
Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and communicating on the
Talk Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and in a private response.
100
Applications
Table 11 PTT Express Icon Descriptions (Continued)
Status Icon Description
The PTT Express Voice client is enabled and muted.
The PTT Express Voice client is enabled but it is not able to communicate due to a VoIP telephony call in progress.
Enabling PTT Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the Enable/Disable Switch to the ON position. The button changes to ON .
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE : This section describes the default PTT Express client configuration. See the PTT Express V1.2 User Guide for de tailed information on using the client.
-
PTT communication may be established as a Group Call. When PTT Express is enabled, the PTT button on the left side of the device is assigned for PTT communication.
Figure 79 PTT Button
PPT Button
101
Applications
Creating a Group Call
1. Press and hold the PTT button and listen for the talk tone.
If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that
PTT Express and the WLAN are enabled.
2. Start talking after hearing the talk tone.
NOTE : Holding the button for more than 60 seconds (default) drops the call, allowing others to make Group calls. Release the button when finished talking to allow others to make calls.
Responding with a Private Response
The Private Response can only be initiated once a Group Call has been established. The initial Private
Response is made to the originator of the Group Call.
1. Wait for an access tone.
2. Within 10 seconds, double-press the PTT button, and listen for the talk tone.
3. If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that
PTT Express and the WLAN are enabled.
4. Start talking after the talk tone plays.
5. Release the button when finished talking.
Disabling PTT Express Voice Client Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the Enable/Disable Switch to the OFF position. The button changes to OFF .
3. Touch .
RxLogger
RxLogger is a comprehensive diagnostic tool that provides app and system metrics. Create custom plug-ins that work seamlessly with this tool. RxLogger diagnoses device and application issues, and tracks information for: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, TCP dumps, Bluetooth logging, GPS logging, logcat, ANR dumps, etc. All logs and files generated are saved in flash storage on the device (internal or external).
102
Figure 80 RxLogger
Applications
103
Applications
Enabling Logging
To enable RxLogger:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch START . RxLogger begins collecting data.
3. Touch .
Disabling Logging
To disable RxLogger:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch STOP . RxLogger stops collecting data.
3. Touch .
104
Applications
RxLogger Utility
RxLogger Utility is a data monitoring application for viewing logs in the device while RxLogger is running.
Access the logs and RxLogger Utility features in the App View or the Overlay View.
In the App View, view logs in the RxLogger Utility.
Figure 81 RxLogger Utility App View
Refer to the device Integrator Guide for detailed information on the RxLogger Utility.
Sound Recorder
Use Sound Recorder to record audio messages.
Recordings are saved on the microSD card (if installed) or the internal storage and are available in the Music application (non-GMS devices) or the Play Music application (GMS devices).
105
Figure 82 Sound Recorder Application
Applications
106
Data Capture
The device supports data capture using:
• integrated imager
• SE4710 scan engine
• SE2100 scan engine
• RS507 Hands-free Imager
• RS6000 Bluetooth Ring Scanner.
IMPORTANT
>
: To determine the integrated scan engine in the device, go to Settings > System > About phone
Hardware components > Scanner .
Imaging
The imager uses imaging technology to take a picture of a bar code, stores the resulting image in its memory, and executes state-of-the-art software decoding algorithms to extract the bar code data from the image. With a 2D imager, the device has the following features:
• Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types.
• Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
Operational Modes
The device with an integrated imager supports two modes of operation, listed below. Activate each mode by pressing the Scan button.
• Decode Mode : In this mode, the device attempts to locate and decode enabled barcodes within its field of view. The imager remains in this mode as long as the user holds the scan button, or until it decodes a barcode.
NOTE
: To enable Pick List Mode, configure in DataWedge or set in an application using a API command.
• Pick List Mode : This mode allows the user to selectively decode a barcode when more than one barcode is in the device’s field of view. To accomplish this, move the aiming crosshair or dot over the required barcode to decode only this barcode. This feature is ideal for pick lists containing multiple barcodes and manufacturing or transport labels containing more than one barcode type
(either 1D or 2D).
107
Data Capture
NOTE : To enable Basic MultiBarcode Mode, configure in DataWedge or set in an application using a API command.
• Basic MultiBarcode Mode : In this mode, the device attempts to locate and decode a specific number of unique barcodes within its field of view. The device remains in this mode as long as the user holds the scan button, or until it decodes all the barcodes. Available on integrated SE2100 or SE4710 imagers only.
• The device attempts to scan the programmed number of unique barcodes (from 2 through 10).
• If there are duplicate barcodes (same symbology type and data), only one of the duplicate barcodes is decoded and the remainder are ignored. If the label has two duplicate barcodes plus another two different barcodes, a maximum of three barcodes will be decoded from that label; one will be ignored as a duplicate.
• Barcodes can be of multiple symbology types and still be acquired together. For example, if the specified quantity for a Basic MultiBarcode scan is four, two barcodes can be symbology type Code 128 and the other two can be symbology type Code 39.
• If the specified number of unique barcodes is not initially in view of the device, the device will not decode any data until the device is moved to capture the additional barcode(s) or time out occurs. If the device field of view contains a number of barcodes greater than the specified quantity, the device randomly decodes barcode(s) until the specified number of unique barcodes is reached. For example, if the count is set to two and eight barcodes are in the field of view, the device decodes the first two unique barcodes it sees, returning the data in random order.
• Basic MultiBarcode Mode does not support concatenated barcodes.
RS507/RS507x Hands-Free Imager
The RS507 and RS507x Hands-free Imagers are wearable barcode scan solution for both 1D and 2D bar code symbologies. The scanner supports Bluetooth Human Interface Device (HID) connection to the device.
Figure 83 RS507/RS507x Hands-Free Imager
Refer to the RS507/RS507x Hands-free Imager Product Reference Guide for more information.
108
Data Capture
RS6000 Bluetooth Ring Scanner
The RS6000 Bluetooth Ring Scanner is a wearable bar code scan solution for both 1D and 2D bar code symbologies.
Figure 84 RS6000 Bluetooth Ring Scanner
Refer to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode, with a few quick trial efforts to master it.
However, consider the following to optimize scanning performance:
• Range: Scanners decode best over a particular working range — minimum and maximum distances from the barcode. This range varies according to barcode density and scanning device optics. Scan within range for quick and constant decodes; scanning too close or too far away prevents decodes. Move the scanner closer and further away to find the right working range for the barcodes being scanned.
• Angle: Scanning angle is important for quick decodes. When the illumination/flash reflects directly back into the imager, the specular reflection can blind/saturate the imager. To avoid this, scan the barcode so that the beam does not bounce directly back. Do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
• Hold the device farther away for larger symbols.
• Move the device closer for symbols with bars that are close together.
NOTE : Scanning procedures depend on the app and device configuration. An app may use different scanning procedures from the one listed above.
Barcode Scanning with Internal SE2100 Imager
To read a barcode, a scan-enabled application is required. The device contains the DataWedge application that allows the user to enable the imager, decode the barcode data and display the barcode content.
1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
109
Data Capture
2. Point the exit window on the top of the device at a barcode.
Figure 85 SE2100 Imager Scanning
3. Press and hold the scan button.
The white aiming pattern turns on to assist in aiming.
4. Ensure the barcode is within the area formed by the aiming pattern.
Figure 86 SE2100 Aiming Pattern
5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully.
6. Release the scan button.
NOTE : Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (im age) of a poor or difficult barcode as long as the scan button remains pressed.
-
7. The barcode content data displays in the text field.
SE2100 Picklist Mode
When Picklist Mode is enabled, the screen displays an image of the barcode and a red cross-hair. See TC20
Mobile Computer Integrator Guide for Android 8.0 Oreo for information on setting Picklist Mode.
110
Data Capture
When the device is in Picklist Mode, the imager does not decode the barcode until the cross-hair touches the barcode.
Figure 87 SE2100 Pick List Mode with Multiple Barcodes in Aiming Pattern
SE2100 Basic MultiBarcode Mode
To read multiple barcodes, a scan-enabled application is required. The device contains the DataWedge application that allows the user to enable the imager, decode the barcode data and display the barcode content.
1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2. Point the exit window on the top of the device at the barcodes.
3. Press and hold the scan button.
The white aiming pattern turns on to assist in aiming.
4. Ensure the barcodes are within the area formed by the aiming pattern.
Figure 88 SE2100 Aiming Pattern with Multiple Barcodes
5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully. Captured data from all barcodes is delivered as a single string.
6. Release the scan button.
111
Data Capture
NOTE : Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (im age) of a poor or difficult barcode as long as the scan button remains pressed.
-
7. The barcode content data displays in the text field.
Barcode Scanning with Internal SE4710 Imager
To read a barcode, a scan-enabled application is required. The device contains the DataWedge application that allows the user to enable the imager, decode the barcode data and display the barcode content.
1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2. Point the exit window on the top of the device at a barcode.
Figure 89 SE4710 Imager Scanning
3. Press and hold the scan button.
The red LED aiming pattern turns on to assist in aiming.
NOTE : When the device is in Picklist mode, the imager does not decode the barcode until the crosshair or aiming dot touches the barcode.
112
Data Capture
4. Ensure the barcode is within the area formed by the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
Figure 90 SE4710 Aiming Pattern
Figure 91 SE4710 Pick List Mode with Multiple barcodes in Aiming Pattern
5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully.
6. Release the scan button.
NOTE : Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (im age) of a poor or difficult barcode as long as the scan button remains pressed.
-
7. The barcode content data displays in the text field.
SE4710 Basic MultiBarcode Mode
To read multiple barcodes, a scan-enabled application is required. The device contains the DataWedge application that allows the user to enable the imager, decode the barcode data and display the barcode content.
1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2. Point the exit window on the top of the device at the barcodes.
3. Press and hold the scan button.
The red LED aiming pattern turns on to assist in aiming.
113
Data Capture
4. Ensure the barcodes are within the area formed by the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
Figure 92 SE4710 Aiming Pattern with Multiple Barcodes
5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully. Captured data from all barcodes is delivered as a single string.
6. Release the scan button.
NOTE : Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (im age) of a poor or difficult barcodes as long as the scan button remains pressed.
-
7. The barcodes content data displays in the text field.
Scanning with RS6000 Bluetooth Ring Scanner
To read a barcode, a scan-enabled app is required. Devices that contain the Zebra DataWedge app allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS6000:
1. Pair the RS6000 with the device. See Pairing Using Bluetooth Human Interface Device for more information.
2. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3. Point the RS6000 at a barcode.
Figure 93 Barcode Scanning with RS6000
4. Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
114
Data Capture
The RS6000 LEDs light green and a beep sounds to indicate the barcode was decoded successfully. When the RS6000 is in Pick List mode, the RS6000 does not decode the barcode until the center of the crosshair touches the barcode.
Figure 94 RS6000 Aiming Pattern
Figure 95 RS6000 Pick List Mode with Multiple Barcodes in Aiming Pattern
5. The captured data appears in the text field.
Scanning with RS507/RS507X Hands-Free Imager
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS507/RS507X:
1. Pair the RS507/RS507X with the device. See Pairing Using Simple Serial InterfacePairing Bluetooth
Scanners or Pairing Using Bluetooth Human Interface Device for more information.
2. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
115
Data Capture
3. Point the RS507/RS507X at a barcode.
Figure 96 Barcode Scanning with RS507/RS507X
4. Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS507/RS507X LEDs light green and a beep sounds to indicate the barcode was decoded successfully. When the RS507/RS507X is in Pick List mode, the RS507/RS507X does not decode the barcode until the center of the crosshair touches the barcode.
Figure 97 RS507/RS507X Aiming Pattern
Figure 98 RS507/RS507X Pick List Mode with Multiple Barcodes in Aiming Pattern
116
Data Capture
5. The captured data appears in the text field.
Pairing the RS507/RS507X/RS6000 Hands-Free Imager
To connect the RS507/RS507X or RS6000 imager to the device, use one of the following methods:
• Simple Serial Interface (SSI)
• Bluetooth Human Interface Device (HID) Mode.
Pairing Using Simple Serial Interface
To pair the RS507/RS507X or RS6000 with the device using SSI.
1. Swipe up from the bottom of the Home screen and touch .
Figure 99 Bluetooth Pairing Utility
2. Using the RS507/RS507X or RS6000, scan the barcode on the screen.
The RS507/RS507X or RS6000 emits a string of high/low/high/low beeps. The Scan LED flashes green indicating that the RS507/RS507X or RS6000 is attempting to establish connection with the device. When connection is established, the Scan LED turns off and the RS507/RS507X or RS6000 emits one string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
Pairing Using Bluetooth Human Interface Device
To pair the RS507/RS507X or RS6000 with the device using Human Interface Device (HID):
1. Ensure that Bluetooth is enabled on both devices.
117
Data Capture
2. Ensure that the Bluetooth device to discover is in discoverable mode.
3. Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4. Place the RS507/RS507X or RS6000 in HID mode. If the RS507/RS507X or RS6000 is already in HID mode, skip to step 5.
a. Remove the battery from the RS507/RS507X or RS6000.
b. Press and hold the Restore key.
c. Install the battery onto the RS507/RS507X or RS6000.
d. Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
e. Scan the barcode below to place the RS507/RS507X or RS6000 in HID mode.
Figure 100 RS507 Bluetooth HID Barcode
Figure 101 RS6000 Bluetooth HID Barcode
5. Remove the battery from the RS507/RS507X or RS6000.
6. Re-install the battery into the RS507/RS507X or RS6000.
7. Swipe down from the Status bar to open the Quick Access panel and then touch .
8. Touch Bluetooth .
9. Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
10.Scroll through the list and select RS507/RS507X or RS6000.
The device connects to the RS507/RS507X or RS6000 and Connected appears below the device name.
The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
A notification appears on Notification panel and the icon appears in the Status bar.
118
Data Capture
DataWedge
DataWedge is a utility that adds advanced barcode scanning capability to any application without writing code.
It runs in the background and handles the interface to built-in barcode scanners. The captured barcode data is converted to keystrokes and sent to the target application as if it was typed on the keypad.
To configure DataWedge refer to the device Integrator Guide or Product Reference Guide.
Enabling DataWedge
1. Swipe up from the bottom of the Home screen and touch .
2. Touch > Settings .
3. Touch the DataWedge enabled checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
4. Touch .
Disabling DataWedge
1. Swipe up from the bottom of the Home screen and touch .
2. Touch > Settings .
3. Touch the DataWedge enabled checkbox. A blue checkmark disappears from the checkbox indicating that
DataWedge is disabled.
4. Touch .
119
Wireless
This section provides information on the wireless features:
• Wireless Wire Area Network (WWAN)
• Wireless Local Area Network (WLAN)
• Bluetooth.
Wireless Wide Area Networks
NOTE : Indonesian configurations do not support LTE.
Use Wireless wide area networks (WWANs) to access data over a cellular network. This section provides information on:
• Sharing a data connection
• Changing Cellular Network settings
• Locking a SIM card
• Monitoring data usage.
Sharing the Mobile Data Connection
The Tethering & Portable Hotspot settings allows sharing the mobile data connection with a single computer via USB tethering or Bluetooth tethering. Share the data connection with up to eight devices at once, by turning it into a portable Wi-Fi hotspot. While the device is sharing its data connection, an icon displays at the top of the screen and a corresponding message appears in the notification list.
Enabling USB Tethering
NOTE
: USB tethering is not supported on computers running Mac OS. If the computer is running Windows or a recent version of Linux (such as Ubuntu), follow these instructions without any special preparation. If running a ver sion of Windows that precedes Windows 7, or some other operating system, you may need to prepare the computer to establish a network connection via USB.
1. Connect the device to a host computer with the USB cable.
2. The notification USB charging this device appears in the Notifications panel.
3. Swipe down from the Status bar to open the Quick Access panel and then touch .
4. Touch Network & Internet .
120
5. Touch Hotspot & tethering .
6. Touch the USB tethering switch to enable.
The host computer is now sharing the device’s data connection.
To stop sharing the data connection, touch the USB tethering switch again or disconnect the USB cable.
Enabling Bluetooth Tethering
Use Bluetooth tethering to share the data connection with a host computer.
Configure the host computer to obtain its network connection using Bluetooth. For more information, see the host computer’s documentation.
1. Pair the device with the host computer.
2. Swipe down from the Status bar to open the Quick Access panel and then touch .
3. Touch Networking & Internet .
4. Touch Hotspot & tethering .
5. Touch the Bluetooth tethering switch to enable.
The host computer is now sharing the device’s data connection.
To stop sharing the data connection, touch the Bluetooth tethering switch again.
Enabling Wi-Fi Hotspot
To enable the Wi-Fi Hotspot:
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Network & Internet .
3. Touch Hotspot & tethering .
4. Touch the Wi-Fi hotspot switch to enable.
After a moment, the device starts broadcasting its Wi-Fi network name (SSID). Connect to it with up to eight computers or other devices. The Hotspot icon appears in the Status bar.
To stop sharing the data connection, touch the Portable Wi-Fi hotspot switch again.
Configuring the Wi-Fi Hotspot
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Network & Internet .
3. Touch Hotspot & tethering .
4. Touch Set up Wi-Fi hotspot .
Figure 102 Set up Wi-Fi Hotspot Dialog Box
5. In the Network name text field, edit the name for the hotspot.
121
6. Touch the Security option and select a security method from the drop-down list.
• None
• WPA2 PSK .
NOTE : If None is selected in the Security option, a password is not required.
7. In the Password text field, enter a password, if required.
8. In the Select AP Band drop-down list, select 2.4 GHz Band or 5 GHz Band .
9. Touch Save .
Cellular Network Settings
The following sections provide settings for cellular networks.
Disabling Data When Roaming
To prevent the device from transmitting data over other carriers’ mobile networks when leaving an area that is covered by the carrier’s networks. This is useful for controlling expenses if the service plan does not include data roaming.
GSM Devices
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Network & Internet > Mobile network .
3. Slide the Roaming switch to the off position.
Enhanced 4G LTE Mode
Use LTE services to improve voice and other communication. This option is enabled by default.
Indonesian configurations do not support LTE.
Using Search for MicroCell
A MicroCell acts like a mini cell tower in a building or residence and connects to an existing broadband Internet service. It improves cell signal performance for voice calls, texts, and cellular data applications like picture messaging and Web surfing.
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Network & Internet > Mobile network .
3. Touch Search for AT&T MicroCell .
Configuring the Access Point Name
NOTE : Many service provider Access Point Name (APN) data are pre-configured in the device. The APN information for all other service provides must be obtained from the wireless service provider.
To use the data on a network, configure the APN information:
122
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Network & Internet > Mobile network > Advanced .
3. Touch Access Point Names .
4. Touch an APN name in the list to edit an existing APN or touch to create a new APN.
5. Touch each APN setting and enter the appropriate data obtained from the wireless service provider.
6. When finished, touch > Save .
7. Touch the radio button next to the APN name to start using it.
8. Touch .
Locking the SIM Card
Locking the SIM card requires the user to enter a PIN every time the device is turned on. If the correct PIN is not entered, only emergency calls can be made.
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Security & location .
3. Touch SIM card lock .
4. Touch Lock SIM card .
5. Enter the PIN associated with the card. Touch OK.
6. Reset the device.
Data Usage
Data usage refers to the amount of data uploaded or downloaded by the device during a given period.
Depending on the wireless plan, you may be charged additional fees when your data usage exceeds your plan's limit.
To monitor your data usage:
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Mobile network > Data usage > Data saver .
CAUTION : The usage displayed on the data usage settings screen is measured by your device. Your carrier's data usage accounting may differ. Usage in excess of your carrier plan's data limits can result in steep overage charges. The feature described here can help you track your usage, but is not guaranteed to prevent additional charges.
Data usage settings allow:
• Set the data usage warning level.
• Set a data usage limit.
• View or restrict data usage by app.
• Identify mobile hotspots and restrict background downloads that may result in extra charges.
By default, the data usage settings screen displays the mobile data settings. That is, the data network or networks provided by your carrier.
123
Setting Data Usage Warning
To set a warning alert when the device has used a certain amount of mobile data:
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Data usage .
3. Touch Mobile data usage > > Set data warning .
4. Touch Data warning .
5. Enter a number. To switch between megabytes (MB) and gigabytes (GB), touch the down arrow.
6. Touch SET .
When the usage reaches the set level, a notification appears.
Setting Data Limit
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Data usage .
3. Touch Mobile data usage > > Set data limit .
4. Touch OK .
5. Touch Data limit .
6. Enter a number. To switch between megabytes (MB) and gigabytes (GB), touch the down arrow.
7. Touch Set .
When the limit is reached, data automatically turns off and a notification appears.
Wireless Local Area Networks
Wireless local area networks (WLANs) allow the device to communicate wirelessly inside a building. Before using the device on a WLAN, the facility must be set up with the required hardware to run the WLAN
(sometimes known as infrastructure). The infrastructure and the device must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches,
Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wireless & networks settings configure the device to match the security scheme.
The device supports the following WLAN security options:
• Open
• Wireless Equivalent Privacy (WEP)
• Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK)
124
• Extensible Authentication Protocol (EAP).
• Protected Extensible Authentication Protocol (PEAP) - with MSCHAPV2 and GTC authentication
• Transport Layer Security (TLS)
• TTLS - with Password Authentication Protocol (PAP), MSCHAP and MSCHAPv2 authentication.
The Status bar displays icons that indicate Wi-Fi network availability and Wi-Fi status.
NOTE : To extend the life of the battery, turn off Wi-Fi when not in use.
Connecting to a Wi-Fi Network
To connect to a Wi-Fi network:
1. Swipe down from the Status bar to open the Quick Access panel.
Figure 103 Quick Access Panel
125
2. Touch Wi-Fi to open the Wi-Fi screen. The device searches for WLANs in the area and lists them.
-
Figure 104 Wi-Fi Screen
3. Scroll through the list and select the desired WLAN network.
4. For open networks, touch profile once or press and hold and then select Connect to network or for secure networks enter the required password or other credentials then touch Connect . See the system administrator for more information.
The device obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the device with a fixed internet protocol (IP) address, Refer to the device Integrator Guide for more information.
5. In the Wi-Fi setting field, Connected appears indicating that the device is connected to the WLAN.
Removing a Wi-Fi Network
To remove a remembered or connected network:
1. Swipe down from the status bar to open the quick access panel and then touch .
2. Touch Network & Internet > W-Fi .
3. Scroll down to the bottom of the list and touch Saved networks .
4. Touch the name of the network.
5. In the dialog box, touch FORGET .
6. Touch .
Bluetooth
Bluetooth devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band
126
(802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 m (32.8 ft)) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (for example, files, appointments, and tasks) with other Bluetooth enabled devices such as printers, access points, and other mobile devices.
The device supports Bluetooth Low Energy. Bluetooth Low Energy is targeted at applications in the healthcare, fitness, security, and home entertainment industries. It provides reduced power consumption and cost while maintaining standard Bluetooth range.
Adaptive Frequency Hopping
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with
Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work.
There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
• Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
• Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
• Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
• Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels.
AFH coexistence allows enterprise devices to operate in any infrastructure.
The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mW and the expected range is 10 m (32.8 ft). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether in open space or closed office space.
NOTE : It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Security
The current Bluetooth specification defines security at the link level. Application-level security is not specified.
This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event).
Authentication of Bluetooth devices is based-upon a challenge-response transaction. Bluetooth allows for a
PIN or passkey used to create other 128-bit keys used for security and encryption. The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
• Perform pairing in a secure environment
127
• Keep PIN codes private and do not store the PIN codes in the device
• Implement application-level security.
Bluetooth Profiles
The device supports the Bluetooth services listed in the table below:
Table 12 Bluetooth Profiles
Profile
Service Discovery Protocol
(SDP)
Serial Port Profile (SPP)
Object Push Profile (OPP)
Advanced Audio Distribution
Profile (A2DP)
Audio/Video Remote Control
Profile (AVRCP)
Personal Area Network (PAN)
Description
Handles the search for known and specific services as well as general services.
Allows use of RFCOMM protocol to emulate serial cable connection between two Bluetooth peer devices. For example, connecting the device to a printer.
Allows the device to push and pull objects to and from a push server.
Allows the device to stream stereo-quality audio to a wireless headset or wireless stereo speakers.
Allows the device to control A/V equipment to which a user has access.
It may be used in concert with A2DP.
Human Interface Device Profile
(HID)
Headset Profile (HSP)
Allows the use of Bluetooth Network Encapsulation Protocol to provide
L3 networking capabilities over a Bluetooth link. Only PANU role is supported.
Allows Bluetooth keyboards, pointing devices, gaming devices and remote monitoring devices to connect to the device.
Allows a hands-free device, such as a Bluetooth headset, to place and receive calls on the device.
Allows car hands-free kits to communicate with the device in the car.
Hands-Free Profile (HFP)
Phone Book Access Profile
(PBAP)
Symbol Serial Interface (SSI)
Allows exchange of Phone Book Objects between a car kit and a mobile device to allow the car kit to display the name of the incoming caller; allow the car kit to download the phone book so you can initiate a call from the car display.
Allows for communication with Bluetooth Imager.
File Transfer Profile (FTP) Provides the capability to browse, manipulate and transfer files in file system of another system. Uses GOEP as a basis.
Generic Attribute Profile (GATT) Provides profile discovery and description services for Bluetooth Low
Energy protocol. It defines how attributes are grouped together into sets to form services.
HID Over GATT Profile (HOGP) Defines the procedures and features used by Bluetooth low energy HID
Devices using GATT and Bluetooth HID Hosts using GATT.
128
Table 12 Bluetooth Profiles (Continued)
Profile Description
Scan Parameters Profile (ScPP) Provides devices with information to assist them in managing their connection idle timeout and advertising parameters to optimize for power consumption and/or reconnection latency.
SIM Access Profile (SAP)
Message Access Profile (MAP)
Allows devices such as car phones with built-in GSM transceivers to connect to a SIM card in a Bluetooth enabled device.
Defines the features and procedures used by devices that exchange message objects.
Bluetooth Power States
The Bluetooth radio is off by default:
• Suspend - When the device goes into suspend mode, the Bluetooth radio stays on.
• Airplane Mode - When the device is placed in Airplane Mode, the Bluetooth radio turns off. When Airplane mode is disabled, the Bluetooth radio returns to the prior state. When in Airplane Mode, the Bluetooth radio can be turned back on if desired.
Bluetooth Radio Power
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (for example, an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the
Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with
Bluetooth radios in close proximity.
NOTE
: To achieve the best battery life, turn off radios when not in use.
Enabling Bluetooth
To enable Bluetooth:
1. Swipe down from the Status bar to open the Quick Access panel.
2. Touch to turn Bluetooth on.
3. Touch .
Disabling Bluetooth
To disable Bluetooth:
1. Swipe down from the Status bar to open the Quick Access panel.
2. Touch to turn Bluetooth off.
3. Touch .
129
Discovering Bluetooth Device(s)
The device can receive information from discovered devices without pairing. However, once paired, the device and a paired device exchange information automatically when the Bluetooth radio is on. To find Bluetooth devices in the area:
1. Ensure that Bluetooth is enabled on both devices.
2. Ensure that the Bluetooth device to discover is in discoverable mode.
3. Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4. Swipe down from the Status bar to open the Quick Access panel.
5. Touch Bluetooth .
6. Touch MORE SETTINGS . The Bluetooth screen appears.
7. Touch Pair new device . The device begins searching for discoverable Bluetooth devices in the area and displays them under Available devices .
8. Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
9. Touch Pair on both devices.
10.The Bluetooth device is added to the Paired devices list and a trusted (“paired”) connection is established.
Changing the Bluetooth Name
By default, the device has a generic Bluetooth name that is visible to other devices when connected.
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Connected devices > Bluetooth .
3. If Bluetooth is not on, move the switch to turn Bluetooth on.
4. Touch Device name .
5. Enter a name and touch RENAME .
6. Touch .
Connecting to a Bluetooth Device
Once paired, connect to a Bluetooth device.
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Connected device > Bluetooth .
3. In the list, touch the unconnected Bluetooth device.
When connected, Connected appears below the device name.
Selecting Profiles on the Bluetooth Device
Some Bluetooth devices have multiple profiles. To select a profile:
130
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Connected Devices > Bluetooth .
3. In the Paired Devices list, touch next to the device name.
4. Turn on or off a profile to allow the device to use that profile.
5. Touch .
Unpairing a Bluetooth Device
To unpair a Bluetooth device and erase all pairing information:
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch Connected devices > Bluetooth .
3. In the Paired Devices list, touch next to the device name.
4. Touch FORGET .
5. Touch .
131
Accessories
This chapter provides information for using the accessories for the device.
Accessories
This table lists the accessories available for the device.
Table 13 Accessories
Accessory
Cradles
1-Slot Base Charge Only
Cradle
1-Slot Ethernet Cradle
Part Number
CRD-TC2X-BS1CO-01
CRD-TC2X-SE1ET-01
5-Slot Charge Only Cradle CRD-TC2X-SE5CO-01
BRKT-SCRD-SMRK-01
Description
Provides charging for device and Extended power pack. Requires power supply
(PWR-WUA5V12W0xx), and USB-C cable.
Provides device charging and communication, and charging for Extended Power Pack.
Requires power supply
(PWR-BGA12V50W0WW), DC line cord
(CBL-DC-388A1-01), and country-specific AC line cord.
Charges up to five devices. Requires power supply (PWR-BGA12V108W0WW), DC line cord (CBL-DC-382A1-01), and country-specific AC line cord.
Mounts the 5-Slot Charge Only Cradle to a wall or rack.
Cradle Mount
Batteries and Chargers
Extended Power Pack
Vehicle Solutions
Cigarette Light Adapter
Auto Charge Cable
Vehicle Cradle
BTRY-TC2X-PRPK1-01
CHG-AUTO-USB1-01
CRD-TC2X-VCH1-01
Charges the device internal battery to provide additional power and extend the shift time.
Provides power to the device from a cigarette lighter socket.
Provides mounting solution for the device in a vehicle.
132
Accessories
Table 13 Accessories (Continued)
Accessory
Audio Accessories
3.5 mm Audio Adapter
Part Number
CBL-TC51-HDST35-01
3.5 mm Headset
Miscellaneous
Trigger Handle
Screen Protector
SmartDEX Solution
Ethernet Bracket
USB/Ethernet Module
Cradle Mating Adapter
Carrying Solutions
TC2X Soft Holster
TC20K Soft Holster
TC2X Hand Strap
TC20K Hand Strap
Wrist/Arm Mount
Small Wrist Mount
Large Wrist Mount
Power Supplies
Power Supply
Power Supply
Power Supply
Power Supply
HDST-35MM-PTVP-01
TRG-TC2X-SNP1-01
KT-TC20-SCRNP1-01
DEX30
BRKT-TC51-ENET1-01
MOD-MT2-EU1-01
KIT-TC2X-BS1FT-05
SG-TC2X-HLSTR1-01
SG-TC20K-HLST1-01
SG-TC2X-HSTRP1-01
SG-TC20K-HSTP1-01
SG-TC2X-ARMNT-01
SG-WT4023221-03R
SG-WT4023221-04R
PWR-BGA12V50W0WW
PWR-BGA12V108W0WW
PWR-WUA5V12W0US
PWR-WUA5V12W0GB
Description
Plugs into the device and provides audio to a wired headset with collared 3.5 mm plug.
Use for PTT calls.
Adds gun-style handle with a scanner trigger for comfortable and productive scanning.
Add additional screen protection.
Provides wireless DEX communications to the device.
Use to connect the USB/Ethernet Adapter to the 1-Slot Ethernet Cradle.
Use with 1-Slot Ethernet Cradle to provide
Ethernet connectivity.
Use the optional mating adapter to connect two or more cradles together. Each cradle still requires a power supply (5-pack).
Use to hold the device on hip. Accepts TC20 device with Trigger Handle.
Use to hold the device on hip. Accepts TC20K device with Trigger Handle.
Replacement hand strap (3–pack).
Replacement hand strap for TC20K (3–pack).
Use to mount the device to the forearm.
Replacement small wrist mount strap.
Replacement long wrist mount strap.
Provides power to the 1-Slot Ethernet Cradle.
Requires DC Line Cord, p/n
CBL-DC-388A1-01 and country specific three wire grounded AC line cord sold separately.
Provides power to the 5-Slot Charge Only cradle. Requires DC Line Cord, p/n
CBL-DC-382A1-01 and country specific three wire grounded AC line cord sold separately.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in the
United States.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in the
European Union.
133
Accessories
Table 13 Accessories (Continued)
Accessory
Power Supply
Part Number
PWR-WUA5V12W0EU
Power Supply
Power Supply
Power Supply
Power Supply
Power Supply
DC Line Cord
DC Line Cord
2-Way DC Line Cord
2-Way DC Line Cord
4-Way DC Line Cord
US AC Line Cord
USB-C Cable
PWR-WUA5V12W0AU
PWR-WUA5V12W0CN
PWR-WUA5V12W0BR
PWR-WUA5V12W0KR
PWR-WUA5V12W0IN
CBL-DC-382A1-01
CBL-DC-388A1-01
CBL-DC-377A1-01
CBL-DC-379A1-01
CBL-DC-380A1-01
23844-00-00R
CBL-TC2X-USBC-01
1-Slot Base Charge Only Cradle
The 1-Slot Base Charge Only Cradle provide 5 VDC for charging:
• TC20 battery
• Extended Power Pack
• TC20 and Extended Power Pack
• TC20 with Trigger Handle.
IMPORTANT : Use only the Zebra USB-C Cable for charging.
Description
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in the
United Kingdom.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in
Australia.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in China.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in Brazil.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in Korea.
Provides 5 VDC, 2.5 A power to the USB-C cable. Includes plug adapter for use in India.
Provides power from the power supply
(PWR-BGA12V108W0WW) to the 5-Slot
Charge Only Cradle.
Provides power from the power supply
(PWR-BGA12V50W0WW) to the 1-Slot
Ethernet Cradle.
Use to charge two 5-Slot Charge only Cradles with one power supply.
Use to charge one 1-Slot Ethernet Cradle and one 5-Slot Charge Only Cradle with one power supply.
Use to charge four 1-Slot Ethernet Cradles with one power supply.
7.5 feet long, grounded, three wire for power supply.
The USB cable used to connect PC to single slot USB cradle.
134
Accessories
Figure 105 1-Slot Base Charge Only Cradle
Charging the Device
To charge a device:
1. Insert the device into the slot to begin charging.
135
Accessories
Figure 106 TC20 Charging
Charge/Notification
LED
2. Ensure the device is seated properly.
Battery Charging
four hours and from fully depleted to 100% in approximately five hours.
NOTE : In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately 10 hours of use.
To achieve the best fast charging results use only Zebra charging accessories and batteries. Charge batteries at room tem perature with the device in sleep mode.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
136
Accessories
1-Slot Ethernet Cradle
The 1-Slot Ethernet Cradle:
• Provides 5 VDC for charging:
• TC20 battery
• Extended Power Pack
• TC20 and Extended Power Pack
• TC20 with Trigger Handle.
• Provides USB communication.
• Provides Ethernet and USB communication using the USB/Ethernet Adapter.
IMPORTANT disabled.
: When the device with attached Extended Power Pack is in the cradle, USB or Ethernet communication is
Figure 107 1–Slot Ethernet Cradle
USB/Ethernet Communication
The 1–Slot Ethernet Cradle with and Ethernet Bracket and USB/Ethernet Module provides both Ethernet communication with a network and USB communication with a host computer. Prior to using the cradle for
Ethernet or USB communication, ensure that the switch on the USB/Ethernet module is set properly. See the
TC20 Mobile Computer Integrator Guide for Android 8.1.0 Oreo for information on setting up the Ethernet
Bracket and USB/Ethernet Module.
137
Accessories
Figure 108 1–Slot Ethernet Cradle Module Switch
For Ethernet communication, slide the switch to the position.
For USB communication, slide the switch to the position.
Place the switch in the center position to disable communications.
Ethernet LED Indicators
There are two LEDs on the USB/Ethernet Module RJ-45 connector. The green LED lights to indicate that the transfer rate is 100 Mbps. When the LED is not lit the transfer rate is 10 Mbps. The yellow LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that there is no link.
Figure 109 LED Indicators
Green Yellow
Table 14 USB/Ethernet Module LED Data Rate Indicators
Data Rate Yellow LED
100 Mbps
10 Mbps
On/Blink
On/Blink
On
Off
Green LED
138
Accessories
Establishing Ethernet Connection
NOTE : settings.
Refer to the TC20 Mobile Computer Integrator Guide for Android 8.0 Oreo for information on configuring the Ethernet
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Ethernet .
3. Slide the Ethernet switch to the ON position.
4. Insert the device into a slot.
The icon appears in the Status bar.
5. Touch Eth0 to view Ethernet connection details.
Charging the Device
To charge a device:
1. Insert the device into the slot to begin charging.
Figure 110 Battery Charging
Charge/Notification
LED
2. Ensure the device is seated properly.
139
Accessories
Battery Charging
four hours and from fully depleted to 100% in approximately five hours.
NOTE : In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately 10 hours of use.
To achieve the best fast charging results use only Zebra charging accessories and batteries. Charge batteries at room tem perature with the device in sleep mode.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
140
Accessories
5-Slot Charge Only Cradle
The 5-Slot Charge Only Cradle provides 5 VDC for charging:
• TC20 battery
• Power Pack
• TC20 and Power Pack
• TC20 with Trigger Handle.
Figure 111 5-Slot Charge Only Cradle
Power LED
Charging the TC20
To charge a device:
1. Insert the device into a slot to begin charging.
141
Device Charging Slot
Figure 112 TC20 Charging
Charge/Notification
LED
Accessories
2. Ensure the device is seated properly.
Battery Charging
four hours and from fully depleted to 100% in approximately five hours.
NOTE : In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately 10 hours of use.
To achieve the best fast charging results use only Zebra charging accessories and batteries. Charge batteries at room tem perature with the device in sleep mode.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
142
Accessories
Extended Power Pack
The Extended Power Pack provides additional power for charging the device battery.
For best performance it is recommended that the Power Pack should always be installed on the device and that both the Power Pack and device are fully charged at the start of each work shift.
Figure 113 Extended Power Pack Front View
LED Button LEDs
Figure 114 Extended Power Pack Back View
Hand Strap
Mounting Point
Charging Contacts
USB Port
(Charging Only)
Installation
To install the Power Pack:
1. Align the Power Pack with the device.
Figure 115 Align Power Pack with TC20
2. Slide the power pack up onto the device until it snaps into place.
Charging
Charge the Extended Power Pack:
• In a cradle
• In a cradle attached to the device
• using a USB cable.
143
Accessories
Figure 116 Charging Power Pack in Cradle
Figure 117 Charging TC20 and Power Pack in Cradle
IMPORTANT : Use only the Zebra USB-C Cable for charging.
144
Figure 118 Charging with USB Cable
Accessories
Power Pack Charging
The power pack charges from fully depleted to 90% in approximately four hours and from fully depleted to
100% in approximately five hours.
Figure 119 Power Pack LEDs
LED Button LED 4 LED 3 LED 2 LED 1
Table 15 LED Charging Indicators
LED 1
LED State
LED 2 LED 3 LED 4
Not charging.
Indication
Charge level is between 0% and 33%.
Flashing
Charge level is between 33% and 66%.
Solid Flashing
145
Accessories
Table 15 LED Charging Indicators (Continued)
LED 1
LED State
LED 2 LED 3 LED 4 Indication
Change level is between 66% and 95%.
Solid Solid Flashing
Fully charged (95-100%).
Solid Solid Solid
Flashing
Charging error, e.g.:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically
10 hours).
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The power pack indicates when charging is disabled due to abnormal temperatures via its LED.
Check Power Level
To check the power level of the power pack, press the LED button. The LEDs light indicating the charge level.
After five seconds the LEDs turn off.
Figure 120 Check Power Level
LED 4 LED 3 LED 2 LED 1
LED Button
146
Accessories
Table 16 LED Charge State Indicators
LED 1
LED State
LED 2 LED 3 LED 4
No charge.
Indication
Charge level is between 0% and 33%.
Flashing
Charge level is between 33% and 66%.
Solid Flashing
Charge level is between 66% and 95%.
Solid Solid Flashing
Solid Solid Solid
Resetting the Extended Power Pack
Fully charged (95-100%).
If the user thinks that the pack is not operating properly, reset the pack:
Press and hold the button for 10 seconds. All four LEDs flash three times.
147
Accessories
Trigger Handle
IMPORTANT : Trigger Handle can only be used on devices with SE4710 imager, and 2-Pin or 8-Pin Access Door.
The Trigger Handle adds a gun-style handle with a scanning trigger to the device. It increases comfort when using the device in scan-intensive applications for extended periods of time.
Figure 121 Trigger Handle
Lanyard Mount
Trigger
Installing the Optional Lanyard
To install the lanyard onto the Trigger Handle:
1. Insert the loop end of the tether into the slot on the bottom of the handle.
2. Feed the lanyard through the loop.
148
Accessories
Figure 122 Install Attachment Plate to Handle
2
1
3. Pull the lanyard until the loop tightens.
Inserting the Device into the Trigger Handle
To install the device onto the Trigger handle:
1. Align and insert the top of the device into the front of the Trigger Handle.
Figure 123 Insert Device into Trigger Handle
2. Rotate the device down and press down until it snaps into place.
149
Accessories
Figure 124 Rotate Device onto Trigger Handle
Removing the Device from the Trigger Handle
To remove the device from the Trigger Handle:
1. Using thumb, push the device up.
Figure 125 Push Device Up
2. Slide the device away from the front of the Trigger Handle.
150
Accessories
Figure 126 Remove Device from Trigger Handle
151
Accessories
Wrist/Arm Mount
The Wrist/Arm Mount allows the user to mount the device onto the forearm for hands-free applications. Install the mount on either arm with the short strap installed closest to the wrist. The user might have to remove and
straps.
Figure 127 Wrist/Arm Mount
Release Latch
Device Mount
Short Strap
Long Strap
Wrist/Arm Mount Installation
To install the Wrist/Arm Mount:
1. Loosen both straps.
2. Slide the Wrist/Arm Mount onto arm with the short strap closest to the wrist.
Figure 128 Slide onto Forearm
Short Strap
Long Strap
3. Tighten both straps on forearm and press hook and loop material together.
152
Figure 129 Tighten Straps
Accessories
Device Installation
To install the device onto the mount:
1. Insert the top of the device into the end of the mount.
Figure 130 Insert TC20 in Holder
2. Rotate the bottom of the device into the mount and snap into place.
153
Figure 131 Secure Device
Accessories
3. Rotate the device for best viewing.
Figure 132 Device Rotation
154
Accessories
Device Removal
To remove the device from the Wrist/Arm Mount:
1. Press down on the release lever.
2. Slide the device out of the mount.
Figure 133 TC20 Removal
Release Lever
Scanning
To scan with device in the wrist mount, rotate the device as shown below.
155
Figure 134 Scanning with Wrist Mount
Accessories
Strap Installation
The user can remove strap for replacement or clean and then re-install new straps.
1. Remove existing straps.
2. Feed the soft end of the strap through the slot on the rear holder with hook material positioned as shown below.
Figure 135 Feed Strap through Rear Slots
Hook Material
3. Fold end over and press hook and loop material together.
156
Figure 136 Fold End and Secure
Accessories
4. Feed the hard end through the slot in the front holder.
Figure 137 Feed End Through Front Slot
5. Fold over and press the hook and loop material together.
Figure 138 Fold End and Secure
157
Accessories
Hand Strap
NOTE : There are two different hand straps for the device and the TC20K. The TC20K hand strap is longer. TC20 hand strap installation is shown below. TC20K hand strap installation is the same.
The hand strap provides securing when holding the device.
To install the hand strap on the device:
1. Feed the top end of the hand strap through the slot at the top of the device.
Figure 139 Insert Hand Strap Through Top Mounting Point
2. Pull the end through the slot.
Figure 140 Feed End Through Slot
3. Insert the end of the hand strap into the slot on the hand strap.
4. Pull the end until the notch sits into the slot.
5. Feed the other end of the hand strap through the slot at the bottom of the device.
Figure 141 Insert Hand Strap Through Bottom Mounting Point
6. Pull the end through the slot.
7. Press the hook material against the loop material.
158
Accessories
Figure 142 Adjust and Close Hand Strap End
8. Place hand between device and hand strap and adjust hand strap as necessary.
To install the hand strap on the device with an Extended Power Pack:
1. Feed the top end of the hand strap through the slot at the top of the device.
Figure 143 Insert Hand Strap Through Top Mounting Point
2. Pull the end through the slot.
3. Insert the end of the hand strap into the slot on the hand strap.
4. Pull the end until the notch sits into the slot.
Figure 144 Feed End Through Slot
5. Feed the other end of the hand strap through the slot at the bottom of the device.
6. Slide the device into the Extended Power Pack.
159
Accessories
Figure 145 Insert Hand Strap Through Power Pack Bottom Mounting Point
7. Pull the end through the slot.
8. Press the hook material against the loop material.
Figure 146 Adjust and Close
9. Place hand between device and hand strap and adjust hand strap as necessary.
160
Accessories
Soft Holster
NOTE : There are two different soft holsters for the TC20 and the TC20K. The TC20K soft holster is longer. TC20 soft holster installation is shown below. TC20K soft holster installation is the same.
Use the soft holster to securely holds the device on a belt for easy access. The holster has an adjustable belt for securing the device or Trigger Handle.
Figure 147 Soft Holster
Adjusting the Holster
The holster has an adjustable belts that securely holds the device or Trigger Handle.
161
Figure 148 Adjust Belts
Accessories
Pull Belts Tight for Device
Leave Belts Loose for Trigger Handle and
Extended Power Pack
Insert the device into the holster with the device exit window facing up and the display against the body.
Figure 149 Device in Holster
Insert the device and Extended Power Pack into the holster with the device exit window facing up and the display against the body.
162
Accessories
Figure 150 Device with Extended power Pack in Holster
Insert the Trigger Handle into the holster with the device exit window facing down.
Figure 151 Trigger Handle in Holster
163
Maintenance and
Troubleshooting
This chapter includes instructions on cleaning and storing the device, and provides troubleshooting solutions for potential problems during operation.
Maintaining the TC25
For trouble-free service, observe the following tips when using the TC25:
• Do not scratch the screen of the TC25.
• The touch-sensitive screen of the TC25 is glass. Do not to drop the TC25 or subject it to strong impact.
• Protect the TC25 from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
• Do not store or use the TC25 in any location that is dusty, damp, or wet.
• Use a soft lens cloth to clean the TC25. If the surface of the TC25 screen becomes soiled, clean it with a soft cloth moistened with a diluted window-cleaning solution.
Display Best Practices
Image Retention
Image retention may occur when a static image continuously displays for extended periods of time. A user may see a faint remnant of the image even after a new image displays. To prevent image retention:
• set the display to turn off after a few minutes of idle time.
• rotate background images on a periodic basis.
• turn off the display when the device in not in use.
• use a screen saver with the following characteristics:
• background color set to black
• use a small moving image (approximately 2% of the display size).
• move the image randomly across the screen
• screen saver should be active as long as the static image is used.
Long-Term Storage
When storing the device for long periods of time, ensure that the battery has at least 50% charge and is stored at (temperature).
164
Maintenance and Troubleshooting
Cleaning Instructions
CAUTION : Always wear eye protection.
Read warning label on compressed air and alcohol product before using.
If you have to use any other solution for medical reasons please contact the Global Customer Support Center for more information.
WARNING : Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, or mild dish soap.
Harmful Ingredients
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: ammonia solutions, compounds of amines or ammonia; acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Cleaning Instructions
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, but gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Allow the unit to air dry before use.
Special Cleaning Notes
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device. The device should not be handled while wearing vinyl gloves containing phthalates, or before hands are washed to remove contaminant residue after gloves are removed. If products containing any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizer that contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the plastics.
Cleaning Materials Required
• Alcohol wipes
• Lens tissue
• Cotton-tipped applicators
• Isopropyl alcohol
• Can of compressed air with a tube.
165
Maintenance and Troubleshooting
Cleaning Frequency
The cleaning frequency is up to the customer’s discretion due to the varied environments in which the mobile devices are used. They may be cleaned as frequently as required, but it is advisable to clean the camera window periodically when used in dirty environments to ensure optimum performance.
Cleaning the TC25
Housing
Using the alcohol wipes, wipe the housing including buttons.
Display
The display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
Camera and Exit Window
Wipe the camera and exit window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
Connector Cleaning
To clean the connectors:
1. Power off the device
2. Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
3. Rub the cotton portion of the cotton-tipped applicator back-and-forth across the connector. Do not leave any cotton residue on the connector.
4. Repeat at least three times.
5. Use the cotton-tipped applicator dipped in alcohol to remove any grease and dirt near the connector area.
6. Use a dry cotton-tipped applicator and repeat steps 4 through 6.
CAUTION : Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face.
7. Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the surface.
8. Inspect the area for any grease or dirt, repeat if required.
Cleaning Cradle Connectors
To clean the connectors on a cradle:
166
Maintenance and Troubleshooting
1. Remove the DC power cable from the cradle.
2. Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
3. Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.
4. All sides of the connector should also be rubbed with the cotton-tipped applicator.
CAUTION : Do not point nozzle at yourself and others, ensure the nozzle or tube is pointed away from your face.
5. Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away from the surface.
6. Remove any lint left by the cotton-tipped applicator.
7. If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.
8. Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and dry humidity requires less drying time.
Troubleshooting
The following tables provides typical problems that might arise and the solution for correcting the problem.
TC25
Table 17 Troubleshooting the TC25
Problem
When pressing the power button the
TC25 does not turn on.
When pressing the power button the
TC25 does not turn on but two LEDs blink.
Battery did not charge.
Cause
Battery not charged.
System crash.
Battery charge is at a level where data is maintained but battery should be re-charged.
Cannot see characters on display.
Battery failed.
TC25 removed from cradle while battery was charging.
Extreme battery temperature.
TC25 not powered on.
Solution
Charge the battery in the TC25.
Perform a reset.
Charge the battery in the TC25.
Contact system administrator.
Insert TC25 in cradle. See Charging the Battery on page
.
Battery does not charge if ambient temperature is below
0°C (32°F) or above 40°C (104°F).
Press the Power button.
167
Maintenance and Troubleshooting
Table 17 Troubleshooting the TC25 (Continued)
Problem
During data communication with a host computer, no data transmitted, or transmitted data was incomplete.
Cause
TC25 removed from cradle or disconnected from host computer during communication.
Incorrect cable configuration.
Communication software was incorrectly installed or configured.
Wi-Fi radio is not on.
You moved out of range of an access point.
During data communication over
Wi-Fi, no data transmitted, or transmitted data was incomplete.
During data communication over
Bluetooth, no data transmitted, or transmitted data was incomplete.
No sound.
TC25 shuts off.
You moved out of range of another Bluetooth device.
Volume setting is low or turned off.
TC25 is inactive.
Solution
Replace the TC25 in the cradle, or reattach the communication cable and re-transmit.
See the system administrator.
Perform setup.
Turn on the Wi-Fi radio.
Move closer to an access point.
Bluetooth radio is not on. Turn on the Bluetooth radio.
Move within 10 meters (32.8 feet) of the other device.
Adjust the volume.
Battery is depleted.
The device is not responding.
The display turns off after a period of inactivity. Set this period to 15 seconds, 30 seconds, 1, 2, 5, 10 or 30 minutes.
Charge the battery.
Reset the device.
Tapping the window buttons or icons does not activate the corresponding feature.
A message appears stating that the TC25 memory is full.
Too many files stored on the TC25.
Too many applications installed on the TC25.
Delete unused memos and records. If necessary, save these records on the host computer (or use an SD card for additional memory).
Remove user-installed applications on the TC25 to recover memory. Select > Apps . Select the unused program and tap Uninstall .
168
Maintenance and Troubleshooting
Table 17 Troubleshooting the TC25 (Continued)
Problem
The TC25 does not decode with reading barcode.
Cause
Scanning application is not loaded.
Unreadable barcode.
Distance between exit window and barcode is incorrect.
TC25 is not programmed for the barcode.
TC25 is not programmed to generate a beep.
Battery is low.
TC25 cannot find any
Bluetooth devices nearby.
Too far from other
Bluetooth devices.
The Bluetooth device(s) nearby are not turned on.
The Bluetooth device(s) are not in discoverable mode.
Cannot unlock TC25.
User enters incorrect password.
Solution
Load a scanning application on the TC25 or enable
DataWedge. See the system administrator.
Ensure the symbol is not defaced.
Place the TC25 within proper scanning range.
Program the TC25 to accept the type of barcode being scanned. Refer to the EMDK or DataWedge application.
If the TC25 does not beep on a good decode, set the application to generate a beep on good decode.
If the scanner stops emitting a laser beam upon a trigger press, check the battery level. When the battery is low, the scanner shuts off before the TC25 low battery condition notification. Note: If the scanner is still not reading symbols, contact the distributor or the Global
Customer Support Center.
Move closer to the other Bluetooth device(s), within a range of 10 meters (32.8 feet).
Turn on the Bluetooth device(s) to find.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to the device’s user documentation for help.
If the user enters an incorrect password eight times, the user is requested to enter a code before trying again.
If the user forgot the password, contact system administrator.
169
Technical Specifications
TC25
The following sections provide technical specification for the device.
Table 18 TC25 Technical Specifications
Item
Physical Characteristics
Dimensions Length: 134.0 mm (5.3 in.)
Width: 71.3 mm (2.8 in.)
Depth: 17.9 mm (0.7 in.)
Weight
Display
Touch Panel
Backlight
Internal Battery
200 g (7.1 oz)
Description
4.3 in. High Definition (800 x 480) WVGA
Capacitive Touch Panel; multi-touch
Light Emitting Diode (LED) backlight
Rechargeable 3,000 mAh (typical) / 2,900 mAh (minimum) Li-Ion.
Expansion Slot
Connection Interface
Notification
Voice and Audio
User accessible microSD up to 32 GB (SDHC) or up to 128 GB (SDXC) formatted in exFAT.
One USB OTG (host/client) type C connector
Audible tone; multi-color LEDs, vibration
PTT Pro and PTT Express support. Voice support (internal speaker/microphone). Two microphones; speaker; and audio jack.
Performance Characteristics
CPU
Operating System
Memory
Output Power
QCOM MSM8937 64-bit, 8-core, ARM Cortex A53 1.4 GHz, 512 kB L2 cache, power-optimization
Android 8.1.0 Oreo
2 GB RAM/16 GB or 32 GB Flash
USB - 5 VDC @ 500 mA max
170
Technical Specifications
Table 18 TC25 Technical Specifications (Continued)
Item
User Environment
Operating Temperature
Storage Temperature
Charging Temperature
Relative Humidity
Drop Specification
Description
-10°C to 50°C (14°F to 122°F)
-40°C to 70°C (-40°F to 158°F)
0° C to 40° C (32°F to 104°F)
Operating: 5 to 95% non-condensing
Multiple 1.2 m (4 ft.) to tile over concrete per MIL-STD at room temperature.
Tumble
Sealing
300 0.5 m (1.6 ft.) tumbles
IP54
Electrostatic Discharge (ESD) ± 20 kVDC air discharge, ± 10 kVDC direct discharge, ± 10 kVDC indirect discharge
Vibration
Thermal Shock
4 g’s peak, 5 Hz to 2 kHz, 1 hour duration per axis
-40°C to 70°C (-40°F to 158°F) rapid transition. 10 cycles: (1 cycle = 1.25 hours at -40°C and 1.25 hours at 70°C.
Interactive Sensor Technology (IST)
Motion Sensor 3-axis accelerometer
Light Sensor
Proximity Sensor
Ambient light sensor to auto adjust display backlight brightness
Automatically detects when the user places the handset against head during a phone call to disable display output and touch input.
Wireless LAN Data and Voice Communications
Radio IEEE 802.11 a/b/g/n/ac/d/r/k/w/v/h/i IPv4, IPv6
Data Rates Supported
Operating Channels
Security and Encryption
2.4GHz: 802.11b/g/n - up to 150 Mbps
5GHz: 802.11a/n/ac - up to 433.3 Mbps
2.4 GHz: Chan 1 - 13; 1 - 11 (US)
5GHz: Chan 36-48, 52-64, 100-140, 149-151, 161-165
Channel Bandwidth: 20, 40, 80 MHz
Actual operating channels/frequencies and bandwidth depend on regulatory rules and certification agency.
WEP (40 or 104 bit); WPA/WPA2 Personal (TKIP and AES); WPA/WPA2
Enterprise (TKIP and AES) — EAP-TTLS (PAP, MSCHAP, MSCHAPv2),
EAP-TLS, PEAPv0-MSCHAPv2.
Certifications
Fast Roam
802.11 a/b/g/n/ac; WPA; WPA2
802.11
171
Technical Specifications
Table 18 TC25 Technical Specifications (Continued)
Item Description
Wireless WAN Data and Voice Communications
Frequency band Worldwide:
LTE: 700/800/900/1800/2100/2600 (FDD 28,20,8,3,1,7);
UMTS/HSPA/HSPA+: 850/900/2100;
GSM/GPRS/EDGE: 850/900/1800/1900
Note: Indonesian configurations do not support LTE.
Americas:
LTE: 700/850/1800/1900, (FDD 12,17,5,2,4); UMTS/HSPA/HSPA+:
850/1700/1900
GSM/GPRS/EDGE: 850/900/1800/1900
GPS Integrated, Autonomous, Assisted GPS (A-GPS), GLONASS, Beidou
Wireless PAN Data and Voice Communications
Bluetooth
Data Capture Specifications
Bluetooth v4.2 Low Energy (LE)
2D Imager
Camera
SE2100 imager (1D and 2D).
SE4710 imager (1D and 2D).
Rear - 8 MP autofocus; f/2.4 aperture; rear camera flash LED generates balancedwhite light; supports Torch mode. (Available only on TC25 with
WSE4710 scan engine).
2D Imager Engine (SE2100) Specifications
Field of View Horizontal - 41.5°
Vertical - 31.7°
Image Resolution
Roll
640 horizontal X 480 vertical pixels
360°
Pitch Angle
Skew Tolerance
Ambient Light
Focal Distance
Illumination System
± 60° from normal
± 60° from normal
Sunlight: 10,000 ft. candles (107,639 lux)
From front of engine: 10.7 cm (4.2 in.)
LED: Ultra white
Pattern Angle: 42° horizontal, 32.0° vertical at 50% intensity
2D Imager Engine (SE4710) Specifications
Field of View Horizontal - 42.0°
Vertical - 28°
Image Resolution
Roll
1280 horizontal X 800 vertical pixels
360°
172
Technical Specifications
Table 18 TC25 Technical Specifications (Continued)
Item
Pitch Angle
Skew Tolerance
Ambient Light
Focal Distance
Laser Aiming Element
Illumination System
Description
± 60° from normal
± 60° from normal
Sunlight: 10,000 ft. candles (107,639 lux)
From front of engine: 19.4 cm (7.64 in.)
LED: 610
Aiming Dot Brightness Level: 130 fcd nominal
LEDs: Hyper Red 660 nm
Pattern Angle: 53° horizontal, 32° vertical at 50% intensity
Table 19 Data Capture Supported Symbologies
Item
1D barcodes
2D barcodes
Description
Code 39, Code 128, Code 93, Codabar, MSI, UPC/EAN, Interleaved 2 of
5, RSS
PDF-417, Micro PDF-417, Composite, TLC-39, Datamatrix, QR Code,
Micro QRCode, Maxicode, Postal codes, Aztec Code, Han Xin
173
Index
Numerics
5-slot charge only cradle kit . . . . . . . . . . . . . . . . . . . . 132
A
adaptive frequency hopping . . . . . . . . . . . . . . . . . . . 127
adjust volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
airplane mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
alarms only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
albums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89, 95
deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90, 96
working with . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
working with albums . . . . . . . . . . . . . . . . . . . . . . . 95
apn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
approved cleanser . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
apps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
adding shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . 43
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
datawedge demonstration . . . . . . . . . . . . . . . . . . . 80
diagnostic tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Gallery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
PTT Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
RxLogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
RxLogger Utility . . . . . . . . . . . . . . . . . . . . . . . . . . 105
shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
sound recorder . . . . . . . . . . . . . . . . . . . . . . . . . . 105
audio modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
automatically block sounds and vibrations . . . . . . . . . 49
B battery
battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
battery optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
change name . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
discovering devices . . . . . . . . . . . . . . . . . . . . . . 130
enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
power states . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Bluetooth call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
174
C
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 51, 74
photo settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
rear camera photo settings . . . . . . . . . . . . . . . . . . 77
rear camera video settings . . . . . . . . . . . . . . . . . . 78
taking photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
video settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 76, 77
change bluetooth name . . . . . . . . . . . . . . . . . . . . . . . 130
conference call . . . . . . . . . . . . . . . . . . . . . . . . . . . 65, 67
connect to WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Index conventions
notational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
cradle
connector cleaning . . . . . . . . . . . . . . . . . . . . . . . 166
cradle mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
cradle mounting adapter . . . . . . . . . . . . . . . . . . . . . . 133
D
data capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
datawedge demonstration . . . . . . . . . . . . . . . . . . . . . . 80
DC line cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
device settings
accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
diagnostic tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
battery test information . . . . . . . . . . . . . . . . . . . . . 84
bluetooth test information . . . . . . . . . . . . . . . . . . . 86
gps test information . . . . . . . . . . . . . . . . . . . . . . . . 85
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
disable bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
disconnect host computer . . . . . . . . . . . . . . . . . . . . . . 59
discover bluetooth devices . . . . . . . . . . . . . . . . . . . . 130
display
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
display size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
do not disturb feature . . . . . . . . . . . . . . . . . . . . . . . . . . 47
E
EAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
edit apn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
emergency calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
enable bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
extended power pack . . . . . . . . . . . . . . . . . . . . . . . . 132
F
feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
file transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
175
G
Gallery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
cropping photos . . . . . . . . . . . . . . . . . . . . . . . . . . .91
deleting albums . . . . . . . . . . . . . . . . . . . . . . . . . . .90
deleting photos . . . . . . . . . . . . . . . . . . . . . . . . . . .92
deleting videos . . . . . . . . . . . . . . . . . . . . . . . . . . .93
getting album information . . . . . . . . . . . . . . . . . . .90
setting photos as contact icons . . . . . . . . . . . . . . .91
sharing albums . . . . . . . . . . . . . . . . . . . . . . . . . . .90
sharing photos . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
sharing videos . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
watching videos . . . . . . . . . . . . . . . . . . . . . . . . . . .92
working with albums . . . . . . . . . . . . . . . . . . . . . . .89
working with photos . . . . . . . . . . . . . . . . . . . . . . . .91
working with videos . . . . . . . . . . . . . . . . . . . . . . . .92
general sound setting . . . . . . . . . . . . . . . . . . . . . . . . .33
account setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
mobile services . . . . . . . . . . . . . . . . . . . . . . . . . . .35
H
hand strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
handset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
hands-free imager . . . . . . . . . . . . . . . . . . . . . . .108, 109
hard reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
harmful ingredients . . . . . . . . . . . . . . . . . . . . . . . . . .165
headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
headset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
home screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
moving items . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
home screen wallpaper . . . . . . . . . . . . . . . . . . . . . . . .45
I
information, service . . . . . . . . . . . . . . . . . . . . . . . . . . .12
K
keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
L
light sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
lock screen notifications . . . . . . . . . . . . . . . . . . . . . . . .41
low battery notification . . . . . . . . . . . . . . . . . . . . . . . . .28
M
managing notifications . . . . . . . . . . . . . . . . . . . . . . . . .40
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
microSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17, 24
monitor battery usage . . . . . . . . . . . . . . . . . . . . . . . . . 28
N
notification icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
notifications
lock screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
managing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
priority notifications only . . . . . . . . . . . . . . . . . . . . 48
O
operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
P pairing
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
photo transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
cropping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91, 97
deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92, 99
deleting albums . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
deleting videos . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
sharing videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
taking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
viewing and browsing . . . . . . . . . . . . . . . . . . . . . . 96
watching videos . . . . . . . . . . . . . . . . . . . . . . . . . . 99
working with . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
working with albums . . . . . . . . . . . . . . . . . . . . . . . 95
working with photos . . . . . . . . . . . . . . . . . . . . . . . 96
working with videos . . . . . . . . . . . . . . . . . . . . . . . . 99
picklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
proximity sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PTT button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PTT Express
audible indicators . . . . . . . . . . . . . . . . . . . . . . . . 100
disabling communication . . . . . . . . . . . . . . . . . . . 102
enabling communication . . . . . . . . . . . . . . . . . . . 101
group calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
notification icons . . . . . . . . . . . . . . . . . . . . . . . . . 100
private response . . . . . . . . . . . . . . . . . . . . . . . . . 102
Voice Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Index
Q
quick access panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
quick settings
edit icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
R
related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
related software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
remove wi-fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
reseting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
ringtone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
RS507
scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
RS507 scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
RS507/RS6000
pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
pairing using Bluetooth HID . . . . . . . . . . . . . . . . .117
pairing using simple serial interface . . . . . . . . . .117
RS6000
scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
RS6000 scanning . . . . . . . . . . . . . . . . . . . . . . . . . . .114
RxLogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
RxLogger Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
S
scan button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
scanning . . . . . . . . . . . . . . . . . . . . . .109, 111, 112, 113
considerations . . . . . . . . . . . . . . . . . . . . . . . . . . .109
RS507 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
RS6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
screen font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
screen protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
screen rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . .30, 32
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
setting
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76, 77
wakeup sources . . . . . . . . . . . . . . . . . . . . . . . . . .34
settings
accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
automatically block sounds and vibrations . . . . . .49
camera photos . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
camera videos . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
do not disturb . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
general sound . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
home screen wallpaper . . . . . . . . . . . . . . . . . . . . .45
limit sounds and vibrations . . . . . . . . . . . . . . . . . .47
override do not disturb for specific apps . . . . . . . .50
priority notifications only . . . . . . . . . . . . . . . . . . . .48
SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
176
SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
soft holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
sound recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
speaker mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
symbologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
T
taking a panoramic photo . . . . . . . . . . . . . . . . . . . . . . 75
transferring files using USB . . . . . . . . . . . . . . . . . . . . . 58
trigger handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
TTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
U
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
using the dialer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
V videos
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93, 99
recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
working with . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
working with videos . . . . . . . . . . . . . . . . . . . . . . . . 99
voicemail setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
W
wakeup sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
wi-fi network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
wireless local area network . . . . . . . . . . . . . . . . . . . . 120
WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
WPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
wrist mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Index
177
www.zebra.com
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce
