Whalen WC-A017 Kenai Comfort Back Manager's Chair User Manual

LOT NUMBER:

DATE PURCHASED: / /

Kenai Comfort Back Manager's Chair

Model # WC-A017

ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS,

SHARP POINTS, SHARP EDGES AS RECEIVED.

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday

Or visit our website at www.whalenfurniture.com

Or e-mail your request to [email protected]

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Mfg., Inc. Page 1 Factory No. 16092

Model # WC-A017

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly.

A – Backrest (1) B – Seat Cushion (1) CL – Left Armrest (1)

CR – Right Armrest (1) D – Mechanism (1) E – Telescoping Cover (1)

F – Gas Lift (1) G – 5 Star Base (1) H – Caster (5)

(1) Ø5/16” x 7/8” Bolt (Qty. 4+1 extra) (2) Ø1/4” x 1” Bolt (Qty. 8+1 extra)

(3) Plastic Cap (Qty. 8+ 1 extra) Allen Wrench (Qty. 1)

Tools required: Allen Wrench (provided).

Please call for replacement parts or assistance: 1-866-942-5362


Model # WC-A017

Assembly Instructions

1. Unpack the unit and confirm that you have all the hardware and required parts.

2. To begin assembly, place 5 Star Base (G) upside down and press the Casters (H) into the holes at the end of each leg.

3. Turn the Star Base (G) upright and insert the thick end of the Gas Lift (F) into the center hole of Star Base. Then position the Telescoping Cover (E) over the Gas Lift (F) and rest it on the

Star Base.



Model # WC-A017


4. Place the Seat Cushion (B) upside down on a flat and protective surface. Align the Mechanism

(D) over the threaded holes on the underside of Seat Cushion (B) with the black tension knob facing the front of the seat, as shown below. Fasten the Mechanism (D) in place with four

Ø5/16” x 7/8” Bolts (1). Securely tighten the bolts with the enclosed Allen Wrench.

1

B

D

Ø5/16” x 7/8” Bolt

(4 used for rear holes)

1

①



Model # WC-A017


5. Turn the Seat Cushion (B) upright and locate the center hole of Mechanism (D) over the Gas

Lift (F). Press down firmly until the seat locks in place.



Model # WC-A017


6. Align and attach Left and Right Armrests (CL and CR) to the Seat Cushion (B) using four

Ø1/4” x 1” Bolts (2) through the bottom two holes of the Armrests and loosely screw into place with the provided Allen Wrench.

Ø1/4” x 1” Bolt

(4 used in this step)

②



Model # WC-A017


7. Position the cushion of Backrest (A) onto the Seat Cushion (B) and align the top threaded inserts on the side of Backrest with the top holes of the Left and Right Armrests (CL and CR).

Insert the Ø1/4” x 1” Bolts (2) through the countersunk holes on the Armrests and loosely screw into the Backrest (A).



②



Model # WC-A017


8. Gently pivot the Backrest (A) to the upright position and align the bottom threaded inserts with the middle holes on the Left and Right Armrests (CL and CR). Secure the Backrest in place with two Ø1/4” x 1” Bolts (2). Go back and fully tighten all bolts with the provided Allen Wrench.

NOTE: Make sure that the Backrest is perfectly aligned with the Seat before tightening all the bolts.

9. Insert the Plastic Caps (3) to cover the countersunk holes on the Armrests (CL and CR).



②

Plastic Cap


③



Model # WC-A017

OPERATING INSTRUCTIONS

1. To Adjust Seat Height

:

While seated, lean forward and reach under the right side of the chair to find the handle. Lift the handle and raise your body up slightly to allow the chair to rise to the desired height. To lower the seat, lift the handle while applying more weight downward on the seat. The chair will descend until the handle is released or the chair reaches the bottom position.

2. To Operate Tilt Lockout:

While seated, reach under the right side of the chair to find the height adjustment handle. Pull the handle all the way out (away from the gas lift) to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and push the handle in towards the gas lift.

3. To Adjust Tension on The Tilt:

Reach under the front center of the chair, grasp the round knob and turn it counter-clockwise to stiffen the tilt mechanism. Turn the knob clockwise to loosen the tilt mechanism. Turn the knob until the desired resistance is reached.



1.

2.

3.

4.

5.

Model # WC-A017

INFORMATION FOR USE

This is one type of office chair for commercial or home use. Please use it only on smooth, even flooring.

The height of the seat can be raised up and down by adjusting the handle of the mechanism. The back can tilt after you pull the handle out.

Please check all bolts, screws and knobs are tight at least every 3 months or as needed.

If parts are missing, broken, damaged or worn, please stop using this product until repairs are done by a trained person.

Only a trained person may replace or repair seat height adjustment components. z z z z z z z

Do not stand on this chair, do not use chair as a stepladder.

Use this product only for seating one person at one time.

Do not use this chair unless all bolts, screws and knobs are securely tightened.

Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.

Use this chair for its intended purpose only.

Use mild detergent only for cleaning.

Failure to follow these warnings could result in serious injury. z

Maximum load weight on chair is 225 pounds (102 kg).

THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM

WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS

INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

LIMITED WARRANTY

We are confident that you will be delighted with your Whalen Furniture purchase.

Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.

To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization. At its option Whalen

Furniture will:

(a) Supply compatible components of current manufacture.

(b) Repair the customer’s component.

The customer must prepay freight on any components returned to the factory. Return freight on components still in warranty will be paid by Whalen Furniture.

This warranty gives you specific legal rights and you may also have other rights which vary from State to State.

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m., PST, Monday to Friday



Whalen WC-A017 Kenai Comfort Back Manager's Chair User Manual

Kenai Comfort Back Manager's Chair

Model # WC-A017

OPERATING INSTRUCTIONS

1. To Adjust Seat Height

2. To Operate Tilt Lockout:

3. To Adjust Tension on The Tilt:

INFORMATION FOR USE

Maximum load weight on chair is 225 pounds (102 kg).

LIMITED WARRANTY

Related manuals

Boss Office Products

B245-BK

Office Star Products

ST205-R100

Safavieh

PAT7004B-SET2

Patio Festival

PF19118-W

Glitzhome

2000900017

Glitzhome

2001100011

Office Star Products

ST205-R100

Glitzhome

2001100005

Glitzhome

2001100014

BestOffice

Office Chair Desk Chair

Eurotech Seating

MT7500

Merax

W22201252