Kodak Instamatic 804 Guide
Kodak Instamatic 804 is an advanced camera that combines ease of use with exceptional image quality. Its automatic features, including exposure control, flash control, and film advance, make it ideal for capturing moments effortlessly. With its rangefinder focusing and illuminated signals for insufficient light and flash readiness, you can be sure of sharp and well-exposed shots in various conditions. The camera accepts all Kodak No. 126 films, allowing you to choose between black-and-white snapshots, color snapshots, or color slides.
PDF
Документ
Реклама
Реклама
DETAILS Film a Film Siza—KODAK Mo. 126 In the KODA: FAK Cartridge; 12- or 20-o<posuré. & Megative Size=28 x 28mm. Lens— 38mm, f/2.B KODAK EKTANAR a Lens Openings—1/2.8 through f/64. @ Lens Attachments—Serles 5. Ring supplied, Shutter—Automatically set @ Speeds—1/60, 1/125, 1/7250; also 1/30, set by exposure control and for flash, Also ' “B* for brief time exposures. Focusing and Viewing a Rangefinder-Superimposed-image type, combined with viewfinder. + Viewfinder—Optical, projected viewframe- type with parallax marks for 5 feet. ® Focusing Range=-3 ft to infinity. E |lluminated signals for insufficient Light and flash readiness. Automatic Film Advance a Spring motor advances film —20 expo- sures, plus leader and trailer. Automatic Daylight Exposure Control a Film speed is set automatically by film cartridge (ASA 25 to 800). a Lens openings set automatically by electric eye. & Automatic shutter control reduces spend after maximum lens opening 15 reached. Automatic Flash Control * Guide number is set automatically by film cartridge (40 to 228). + Built-in socket for 4-bulb Flashcuba, a Correct lens opening ls set by focusing. a Flash shutter speed (1/30 sec.) Is set automatically by inserting Flashcubae. e Usas 2 N-5ize manganese alkaliné batteries, Other Features a Instant Loading and Unloading. a Exposura Compansation, a Tripod Socket. a Eyelat for neckstrap (supplied). + Die-cast metal body; black and satin chrome finish. EASTMAN KODAK COMPANY - Rochester, New York 14650 Pt, Ma, 633044 B-65-CH-DX Printed in the United States &f Amorico KODAK Y K INSTAMATIC 804 Camera is the most INSTAMATIG En member of the KODAK INSTAMATIC В 0 4 family. In addition to its instant-loading feature, fine f/2.8 lens, electric-eye exposure and automatic flash С АМ FR А exposure controls, it provides rangefinder focusing, automatic film advance, illuminated finder signals, and automatic flashbulb advance with the new Flashcube. Simply do this... e Drop in KoDAraK Cartridge—camera 1s loaded e Wind Spring-Power Motor—first exposure is ready e Look through Viewfnder and adjust Rangefinder— camera is focused e Compose picture and press Shutter Release—you've | taken the picture 2 ... read on for the details Your camera takes all three— 1 Black-and-white snapshots 2 Color snapshots 3 Color slides a= Before making any important pictures— of a trip or some special event — it is well to shoot a car- tridge of film out doors, and indoors with flash. This will give you practice in camera operation and provide a check on your equipment. 3 KODAK VERICHROME Pan Film, VP 126 В FILM Your camera accepts all Kopag No. 126 Films in thé KODAPAK Cartridge for instant camera loading and un- loading. Konacxrome-X Film, KX 126 [> You can make black-and-white snapshots, color snapshots, or color slides, depending on which film type is loaded in the camera. KopacoLor-X Film, CX 126 | Kopak EXTACHROME-X Film, EX 126 be NOTE: Storing the camera with the motor fully wound does not weaken the spring. If, after a cartridge has been removed from the camera, the shutter release is pressed, the spring tension is released. For the spring motor to again retain power, a cartridge must be loaded in the camera. For 12 black-and-white snapshots. Standard enlarged black-and-white prints from your negatives are 344 x 34 inches in size. Bigger enlargements are also avail- able. For 12 color snapshots. Standard enlarged color prints are 314 x 3% inches in size. Color slides, as well as bigger color enlargements, are also available. For 20 color slides. These color pictures on film are framed in 2 x 2-inch mounts, for showing in slide pro- jectors. For 20 color slides. Can be processed by the user or by a laboratory. These color pictures on film are usually framed in 2 x 2-inch mounts, for showing in slide pro- jectors. Films, processing, printing, and mounting service, can be obtained from your photo dealer. MOTE: You always obtain color négatives from Fopacol or-X Film. These negatives are primarily for enlarged color prints, but you can also obtain color slides fram thé négatives. From KODACHROME-X or KODAK EXTACHAOME-X, you obtain color slides, ready for pro: jection. You can also have duplicate slides or en- larged color prints made from the original slides. LOADING Open the back of the cam: era by sliding the LOCK but- ton down to pop open the hinged cover, then swing out the cover, as far as it will go, until |t “click-stops" approximately perpendicu- lar to the camera. Place a KODAPAK Cartridge in the camera, as ¡Ius trated, with the larger cylin- drical end down and toward the lock button. Close the back of the cam- era by pressing the back against the body until it locks. The film name and number of exposures per cartridge appear in the WIN- DOW on the back of the camera. The film speed and flash guide number are now automatically set. (If the motor Is wound, the first exposure positions itself im- mediately.) m mm mm. 1:1 COUNTER © 4 Raise the black PULL-TAB, draw the winding tape straight out (as above); then, while still grasping the tab, allow the tape to return —repeat until the motor is fully wound (about 7 full strokes or until locked.}® This windup positions film for the first exposure and provides power to advance the film automatically for subsequent exposures. If an arrow shows in the window, the first exposure hasn't bean reached, thus indicating insufficient windup. To get the maximum number of advances, wind the motor fully after ex- posure “1 is in place. The number that appears in the center of the window on the | back of the camera (shown above, right) serves as your exposure COUNTER. The same number may appear in duplicate. ® After winding, make sure the pull-tab is fully seated in is recess; otherwise, film will not advance. UNLOADING 1. After the last picture, the yel- low paper will automatically move past the window, provided the spring motor has been wound sufficiently. If not and an “A” shows In the window, before opening the back of the camera, draw out the winding tape a few strokes to advance the yellow paper beyond the window. 2. Slide down the lock button; apen the back. 3. Turn the camera over to al low the cartridge to fall into your hand. Close the back. For proc- essing, send entire cartridge. NOTE: Do not remove the car- tridge from the camera until all the yellow paper, with the "Xs," has been moved past the window; otherwise several exposures will be “light-Togged.” Removing and replacing partially-exposed car- tridges, even under darkroom con- ditions, may result in loss of one or more exposures due to possi- bla loss of tension on the car tridge take-up spool. it ГЕ aL f | Na Ва nds! SHUTTER SETTING Г LEER [ | rarer | Your camera has four manually | ELECTRIC MES == || adjustable shutter settings — 60 | : i TOR = (1/60 sec.), 125, 250, and “B” — plus 1/30, which is automatical- ly selected for flash by inserting the FLASHCUBE in MEN DA A | shutter speed of 1/1 15 sill for general daylight picturetaking; the faster speed (250) is use- ful to minimize the effect of subject or camera movement, while the slower speed (60) can be used for less favorable light conditions, If there is not sufficient available light for proper exposure at the slowest shutter speed (selected automatically; page 9), a red warning SIGNAL, "E FLASH, will appear in the viewfinder, as the shutter release is slightly depressed. If flash is not appropriate, use the “B” (Brief time) setting — the shutter opens when the shutter release is fully depressed and closes when pressure is removed. After each “B" exposure the shutter selling moves automatically to 250 *Batteries must be installed, as on page 14, to power the warning signal. (1/250) and can easily be reset for another “B” exposure. The camera must be on a solid support, such as a tripod, for these longer exposures, To select a shutter setting, rotate the knurled shutier speed DIAL so that the desired speed number or “B” clicks into place opposite the speed INDEX, AUTOMATIC DAYLIGHT EXPOSURE CONTROL The size of the lens opening is automatically controlled by the amount of light reflected to the ELECTRIC EYE by the scene. Make sure that the electric eve is not obstructed during picture- | taking by the fingers or any other object, and that the camera is nat pointed directly toward the sun or other unusually bright fight source. x In weak light, when the lens opening has reached its largest opening (f/2.8) the shutter, regardless of the dial setting, auto- SIGNAL? matically begins to reduce speed (except at “B”) to give the cor- rect exposure, as far as 1/30, if necessary, A red warning SIGNAL, USE FLASH, will appear, as the shutter release is slightly depressed, in the right side of the luminous frame of the viewfinder, if there is insufficient light for a properly exposed picture — this indicates use of either flash or a “B" exposure. Under these low-light conditions, judge “B" exposure times on the basis of f/2.8. ELE 10 Unusual Situations: Because the electric eye reads the over-all brightness of a scene, better results sometimes can be obtained by altering the exposure when there 1s considerable brightness difference between the subject and the back- ground. If vou wish to give one stop more exposure for a dark subject against à larger light background, rotate and hold the knurled coMPENSATOR as far as it will go toward the plus (4) sign while taking the picture; for a light subject against a larger dark background, you can give one stop less exposure by rotat- ing and holding the COMPENSATOR as far as it will go toward the minus (—) sign, during exposure, The compensator resets to normal when released. This схрозиге compensator can also be used with flash to give one stop more expo- sure [or a dark subject, or one stop less for a light subject. Also, in daylight pictures, when severe brightness differences occur between the subject and the background and it is possible to get close to the subject, you can exclude the background by moving up to a place where only the sub- ject fills the finder. Then press down the shutter release, shown, page 13, about 4% of the way (not far enough to release the shutter), continue to hold the release in this position to maintain the close-up exposure setting; then step back, aim, and press the release down fully to take the picture. VIEWING AND FOCUSING Hold the camera close to your eye with the eye cen- tered on the rear eyepiece so that the complete lumi- nous viewframe is visible. The image seen within this viewframe will be included in the picture, except at short camera-to-subject distances.* The two indicators (one on each side) near the top of the frame, and the one at the lower left, provide parallax correction at a subject distance of about 5 fect. Therefore, when the subject is at about this distance, aim the camera so that the subject image 15 within this smaller area, as outlined by the dotted lines in the illustration at left. NOTE: Since the picture area ls square, there will be no format advantage in holding the camera vertically. “Rangefinder and scale-focus distances are figured to the film plane marker (<>) on the top of the camera. Use this point if measuring for close distances. 11 Тор Шиа оп: Оси ble Image in range finder Indicates out- offocus subject. Lower Illustration: Single rangefinder image means camara is properly focused. Rangefinder Focusing—As you look through the view- finder, you will also notice a circular area in the center of the field of view—this is the rangefinder field. Until the camera is focused for the correct camera-to-subject distance, this field shows a double image of the subject. To set the distance correctly, rotate the LENS MOUNT, by its convenient knob, until the outlines of the double image move together and coincide, so that only one image is visible. The lens is now properly focused. Scale Focusing—You can also focus by turning the lens mount until the figure representing the camera-to-sub- ject distance in feet (or symbol for CLOSE-UP, GROUP, Or SCENE) 15 opposite the focusing MARK. === MARK = 5 q de gi © rw i FL. E 1% hd hero Md er ; SHUTTER E _ RELEASE DAYLIGHT PICTURES « Set the shutter speed. For general picturetaking, the shutter-speed setting may be left at 125, ® Focus the camera for the camera-to-subject distance by using the rangefinder, symbols, or the footage scale on the lens mount, e View the subject, as illustrated, with your eye close to the rear opening of the viewfinder so that the sub- ject is framed by the luminous viewfinder. If, as the shutter release is slightly depressed, the red warning sighal appears in the right side of the viewframe, there's not sufficient light for proper exposure. How- ever, flash can be used for close subjects от а “В” exposure for a still subject. e Hold the camera steady and take the picture by slow- ly pressing the SHUTTER RELEASE all the way down. e With the spring motor wound, film advances auto- matically to the next frame when pressure is re- moved from the shutter release, 13 FLASH PICTURES Your camera features easy, rapid flash picturetaking with the new rotating Flasheube, and automatic flash control — the correct lens opening is automati- cally set as you focus for the camera-to-subject distance. The rotating Flash- cube incorporates 4 blue bulbs (for all films}, reflectors and flashguards. e For color slides, use Kobak EKTACHROME-X Or KODACHROME-X Film, « For color prints, use KopacoLor-X Film. e For black-and-white prints, use KODAK VERICHROME Pan Film. Batteries: Two fresh photoflash or flashlight, N-size, batteries (manganese alkaline recommended) are required to power flashbulbs and finder signals.* Weak batteries may cause flash failures. To install batteries, first open the battery compartment on the bottom of the camera, as shown, by inserting the thumb- nail in the notch, pressing in the direction of the arrow, and swinging open the hinged cover, Insert the batleries —one base | down; the other base up—as illustrated. Close the cover securely. *To insure dependable battery and camera service, clean battery contacts periodically with a rough cloth. For maximum protection of camera contacts, batteries may be removed if camera 15 stored. eE Sy | TAKING FLASH PICTURES e Insert Flashcube—Fit the hollow stem on the base of the Flashcube over the center hub of the socket on the top of the camera, so that the 4 wings of the Flashcube stem enter the cross around the socket hub; then press down the Flasheube until it snap-locks in place with y” FLASHCUBE a % one of its four sides facing forward in its detent (click- | stop) position. If a fresh bulb is in the frontal firing | position, à FLASH READY SIGNAL appears in the left side of the viewframe as the shutter release is slightly de- pressed. Absence of this signal indicates that the cube is not detented in its frontal firing position or that a N mn used bulb is in the forward position. Also, a dim signal = or no signal can indicate that batteries should be Jara checked and possibly replaced. The USE FLASH signal may or may not appear, depending on the amount of illumination present. The cube revolves*® one quarter turn (clockwise) each time the film advances to the next exposure, thus providing flash for 4 exposures if a fresh cube is in place. Tf a partially used cube is in place, a fresh bulb must face forward; if a *IMPORTANT: Do not obstruct rotation of the Flashcube. 15 16 second fresh bulb is facing toward the EJECTOR button, it will rotate into posi- tion as film is advanced. The cube can also be rotated by hand to bring any fresh bulb to its frontal firing position. Press down the EJECTOR button (shown, page 15) to remove a Flashcube. e Set Distance— Rotate the lens mount until the two rangefinder images coin- cide, or until the figure representing the camera-to-subject distance in feet 15 opposite the focusing mark. Distance limit, 25 feet for flash. mos e View Subject—Look through the eyepiece and compose the picture within the luminous viewframe of the viewfinder. e Take Picture—Hold the camera steady and slowly press the shutter release to flash the bulb and take the picture. AUTOMATIC FILL-IN FLASH | | When flash is used in combination with available light (fill-in flash) the elec- | mines the lens opening on the basis of available light at 1/30 CEN and the flash DENIES ek. fat determines the lens opening on the hasis of the distance setting in the 3 to 25 foot range. Che smaller of the e. openings is automatically set when taking the picture. At short e dis- tances or relatively low available light levels, fill-in Nash will produce better lighted pictures, especially of side- or back-lighted subjects. PHOTO AIDS You can extend your picturetaking scope and enjoyment with the photo aids described below, See your Kodak dealer for these and others. KODAK INSTAMATIG Field Case, Model F— This altractively lined, molded case will provide maximum camera protection. The special design permits instant picturetaking, load- ing and unloading without removing the camera from ils case. A KODAK INSTAMATIC Compartment Case is available for carrying camera, film, bulbs, filters, ete. Kopbak Lens Attachments—A removable ring is provided on the front of the lens mount of your camera to retain a Series 5 Kopak Filter or other useful lens attachment. For example: A Kobak Skylight Filter (No. 1A) adds warmth to color pictures taken in the shade or on overcast days, and reduces bluish haze in landscape shots; KODAK PForTRA Lenses can extend the camera's picturetaking range down to 10 inches, portra lens-to-subject distance, with an approximate field size of 6% X 6% inches, Merely unscrew the ring on the front of the lens mount, insert a filter or other lens attachment; then screw the ring in place to hold the accessory. Kooax Projectors—A Kopak Projector will show your color slides big, bright, and sharp on the screen. Ask your dealer to see the revolutionary, fully-automatic Konak CaroUSEL Projector. Features round, 80-slide trays that change as quickly and easily as a hi-fi record. Other features include remote focus, remote forward slide change, remote reverse, instant editing and 500-wait power. 17 CARE OF THE CAMERA Your KODAK INSTAMATIC Is à fine, ruggedly built camera, but yet a precision instrument. Pro- tect it from dust and dirt and avoid rough handling. Use a rub- ber syringe to blow out any dust that may accumulate inside the camera. If the lens needs clean- ing, first brush or blow away any grit or dust, then wipe the surface gently with Kopak Lens Cleaning Paper. If necessary, use KODAK Lens Cleaner. Do not attempt to make any repairs or remove any parts from the shutter, lens, or camera. Never oil the shutter or any other parts of the camera. 18 GUARANTEE Within a year after purchase, any repairs necessary to this Konax InstamaTic Caméra due to à defect in materials or workman- ship will be made or, at our option, the cam- era will be replaced without charge. No other warranty or guarantee, express OT implied, shall be applicable to this equipment. Nor are we responsible for loss of film, for other ex- penses or inconveniences, of for any conse- quential damages occasioned by the equip meant. In case of a defect, the camera can be sent directly or through a Kodak dealer to Eastman Kodak Company or a repair firm authorized by us to make such repairs. ® It should be accompanied by a description of the trouble encountered and other available information regarding the camera, including the date and place of purchase. “Kodak service facilities, with addresses, are described on the following page- EASTMAN KODAK COMPANY Rochester, New York 14650 If your Kodak camera should require attention, complete service facilities are provided at Rochester and in Kodak Regional Sales Divisions at the addresses opposite. Also, service covered under the guarantee is available through independent service shops in many cities. For such local, guarantee covered service, please see your Kodak dealer or refer to the yellow pages of your tele- phone directory under Photo- graphic Equipment and Sup- plies—Factory Approved war: ranty Service, ———BERYICE FACILITIES —— Eastman Kodak Company Apparatus Service #200 Lea Road Rochester, New York 14650 Eastman Kodak Company Apparatus Service 1901 West 22nd Street Oak Brook, Illinois 60523 Eastman Kodak Company Apparatus Service 6300 Cedar Springs Road Dallas, Texas 75235 Eastman Kodak Company Apparatus Service 5315 Peachtrée Industrial Blvd, Chamblee, Georgia 30005 Eastman Kodak Company Apparatus Service 3250 Yan Ness Avenue san Francisco, California 94119 Eastman Kodak Company Apparatus Service 1334 York Avenue New York, New York 10021 Eastman Kodak Company Apparatus Service 808 Rivera Road Whittier, California 90606 Eastman Kodak Company Apparatus Service 1065 Kapiolani Blvd. Honolulu, Hawaii 96807 19 ">
/
Завантажити
Просто дружнє нагадування. Ви можете переглянути документ прямо тут. Але найголовніше, наш штучний інтелект вже прочитав його. Він може пояснити складні речі простими словами, відповісти на ваші запитання будь-якою мовою та допомогти вам швидко орієнтуватися навіть у найдовших або найскладніших документах.
Реклама