N. y, Gordon Bo
MAY 1 21967
www.orphancameras.com
KODAK
Retina Shi
Camera
Your KoDAK RETINA S1 Camera is a
member of the long line of traditionally
excellent RETINA cameras. A certain
pride of ownership comes with this
knowledge. Features of this versatile
camera include . . . unique daylight ex-
posure control . . . automatic flash ex-
posure control with rotating flashcube
. . . easy loading and unloading . . . plus
many other features which promise
picture-taking ease and picture quality.
e Before taking any important pictures—on a
trip or of a special event—take some test pic-
tures to check the camera and your operation
of it. Expose pictures outdoors, and indoors
with flash. If time is pressing, black-and-white
film can be processed very quickly.
Note: Equipment subject to minor appearance
changes.
PICTURE-TAKING. .. It’s as easy as A-B-C!
After loading, and setting the film speed, you...
A B
Set the shutter speed; for Set the lens opening for
example, at 125 (1/125 the prevailing lighting
sec.). condition.
С
Set the distance for Close-
ups, Groups, or Scenes.
... Youre ready to take the picture. Read on for the important details of
camera operation.
Note: The shutter release on your camera cannot be depressed unless film has been
loaded in the camera, as on page 6.
www.orphancameras.com
FILMS
Your camera accepts KOoDAK 135 film. You can make color prints, black-
and-white prints, or color slides. Prints are handy to carry, mail, and make
enlargements of—slides are brilliant, compact, and good for showing to
large groups. Select the film that provides the type of picture you want.
color films
KoDACHROME II Film—For color slides for projection or from which color prints or
enlargements can be made. Expose by daylight or blue flashbulbs. 20 or 36 exposures. |
KODACHROME-X Film—A higher-speed film than KoDACHROME II, this film also yields
color slides for projection or from which color prints and enlargements can be made.
Expose by daylight or blue flashbulbs. 20 or 36 exposures.
KoDAK EKTACHROME-X Film—For color slides for projection, or from which color prints
and enlargements can be made. You can process this film yourself or have it processed
by a laboratory. Expose by daylight or blue flashbulbs. 20 or 36 exposures.
KoDACOLOR-X Film—A negative color film for color prints, enlargements or from which
color slides can be made. Expose by daylight or blue flashbulbs. 20 exposures.
Kobak High Speed EKTACHROME Film—This extremely fast film permits excellent color |
pictures in low illumination. Yields color slides for projection or from which color prints
and enlargements can be made. Available in Daylight Type (for exposure in daylight or
by blue flashbulbs) or Type B (for tungsten light). 20 or 36 exposures.
4
SO
black-and-white films
KoDAK PANATOMIC-X Film—The film to use for big en-
largements when high film speed is not needed. It
has exceptionally fine grain and the ability to record
extremely fine detail. 20 or 36 exposures.
Kobak PLus-X Pan Film—An excellent high-speed
panchromatic film for general outdoor and interior
use. The fine grain and high resolving power permit
high-quality enlargements. 20 or 36 exposures.
KoDAK- TRI-X Pan Film—An extremely fast panchro-
matic film of moderate contrast, wide exposure and
development latitude, and color sensitivity suitable
for all types of illumination. 20 or 36 exposures.
How to get your film processed—by Kodak
or other laboratories offering such service—is
described in the instructions packed with the
film.
ASA FILM SPEEDS
www.orphancameras.com
Loading—always in subdued light
1 To open the back cover of the camera,
press in the bright metal cover LATCH, as
shown, until the cover springs open.
2 As shown opposite, place the film magazine
in its compartment, and rotate the built-in
TAKE-UP SPOOL until one of the two white
pressure CLIPS is up; then slide the film edge
under the white clip as far as possible in the
direction of the arrow.
3 Close the back of the camera. Swing out
the film RAPID WIND LEVER and allow it to re-
turn—repeat until the lever locks.
4 Press down the SHUTTER RELEASE; then
operate the rapid wind lever until it locks
again. Repeat this operation once more to
bring the figure 1 into the center of the expo- .
sure COUNTER. You are now ready for the
first exposure. The exposure counter indi-
cates the number of exposures taken.
6
ur a
www.orphancameras.com
SETTING THE FILM SPEED
Set the speed of the film loaded in the camera before taking pictures—other-
wise pictures will be incorrectly exposed. ASA film speed values are given
on page 5 and in the instructions packed with the film.
To set the film speed, press in and hold the Lock stud while turning the
black knurled ring until the proper film speed number (or indicated number)
on the scale labeled ASA* is opposite the orange INDEX line. A film speed
setting of 64 is shown in the illustration.
*The scale marked DIN (15-27) applies to films rated by a different method.
INDEX
SELECTING THE SHUTTER SPEED
Your camera has the following shutter speeds: 30 (1/30 second), 60, 125,
and 250. These settings, along with the blue flashcube symbol (for flashcube
pictures only, see page 17) and the letter “B,” for time exposures (see page
20), are provided on the SHUTTER-SPEED SCALE.
A shutter speed of 1/125 (marked in red) is recommended for general
daylight picture-taking. The faster shutter speed of 1/250 is useful to mini-
mize the effect of subject or camera movement, while the slower speeds of
1/60 and 1/30 can be used for less favorable lighting conditions.
Rotate the SHUTTER-SPEED SCALE until the number representing the
desired shutter speed “clicks” into place opposite the red INDEX DOT. Do
not make intermediate settings.
www.orphancameras.com
SELECTING LIGHT-CONDITION SYMBOL (Daylight Pictures)
From the blue and gray scale, select the light-condition symbol which rep-
resents the prevailing light condition. Rotate the LENS OPENING DIAL by its
black, knurled ring until this symbol is opposite the black triangular
POINTER. This setting adjusts the lens opening for the light condition
selected on the symbol scale.
If a symbol in the blue background (good lighting conditions) cannot be
set opposite the triangular pointer, select a faster shutter speed (1/250 in-
stead of 1/125). If a symbol in the gray background (poor lighting condi-
tions) cannot be set opposite the triangular pointer, select a slower shutter
speed.
If you prefer to make f-number settings directly, lens opening values
from f/2.8 to f/22 on the lens opening scale can be set opposite the white
index line.
10
cs а лонй
|
|
x
a
Th
Sy
E
St
HEAVY OVERCAST OR HIGH ALTITUDE, BEACH OR
OPEN SHADE SNOW SCENES IN BRIGHT SUN
CLOUDY-BRIGHT AVERAGE SUBJECTS IN
(NO SHADOWS) BRIGHT SUN (DISTINCT SHADOWS)
HAZY SUN (INDISTINCT SHADOWS) OR
SIDE-LIGHTED CLOSE-UPS IN BRIGHT SUN
www.orphancameras.com
SETTING THE FOCUS
Handy, Zone Focusing: For quick focusing, a symbol-type scale appears on
the FOCUSING SCALE. The right hand (head and shoulders) symbol represents
CLOSE-UPS (3% to 8 feet), the middle symbol represents GROUPS (8 to
18 feet), the left hand symbol represents SCENES (beyond 18 feet). Rotate
the focusing ring to position a symbol opposite its triangular pointer.
Scale Focusing: For more accurate focusing (distance setting), and always
for flash, use the footage scale. Estimate the camera-to-subject distance
carefully; then rotate the focusing ring until the orange number, represent-
ing the camera-to-subject distance in feet, is opposite its triangular pointer.
The blue bar under the footage scale is useful for flash only. A metric scale
(white figures) is also provided for distance settings in terms of meters.
gman y
VIEWFINDER
Hold the camera either horizontally or ver-
tically, depending on the nature of the subject.
Center your eye on the rear eyepiece of the
viewfinder so that the complete luminous
viewframe in the finder is visible. The image
seen within this viewframe will be included
in the picture, except at short camera-to-
subject distances. To avoid “cut-off” when
the subject is closer to the camera than 7 feet,
aim the camera so that the subject image is
below or within an imaginary line drawn be-
tween the two pointers on opposite sides of
the luminous viewframe, as illustrated above.
An equal area will be added to the opposite
boundary of the picture. | |
www.orphancameras.com
SHUTTER RELEASE AND FILM ADVANCE
Because of the double-exposure prevention
feature of your camera, the SHUTTER RELEASE
can be depressed only after the RAPID WIND
LEVER has been operated. Always press down
the shutter release as far as it will go with a
slow, squeezing action.
Swing out the rapid wind lever to the limit
of its travel and allow it to return to its orig-
inal position; this sets the shutter and ad-
vances film for the next exposure.
DAYLIGHT PICTURE-TAKING STEPS
After loading the camera and setting the ASA film speed . . .
1 Set the shutter speed; 1/125 sec (125) is recommended for general picture-taking.
2 Set the lens opening by bringing the appropriate light-condition symbol opposite the
black triangular index.
3 Set the focus by the handy 3-symbol scale, or by setting the footage scale for the
camera-to-subject distance in feet.
4 Compose the picture within the luminous viewframe of the finder.
5 Hold the camera steady and press the shutter release all the way down with a slow,
squeezing action to take the picture.
14
UNLOADING—always in subdued light
After the last exposure (20 or 36), and
before opening the camera, rewind
the film into its magazine, as follows.
(1) Push in the REWIND LOCK. Hold it
and push the REWIND SLIDE toward
the base until it locks in its down
position. (2) Operate the film RAPID
WIND LEVER until the diamond-shaped
mark (®) is centered in the exposure
COUNTER; then, operate the lever sev-
eral more strokes to wind the film into
the magazine. (3) Open the back cover
of the camera by pressing the cover
latch on the bottom of the camera
(shown on page 6), and remove the
film magazine.
FLASH PICTURES
Your camera provides X-type synchronization for the 4-bulb flashcube,
flashbulbs (in cordless-type flasholders), and electronic. flash.
Battery: One 5.6 volt, mercury-type battery such as the Mallory PX-23
(supplied) is required to supply power to fire flashcubes. Open the battery
compartment on the bottom of the camera by pushing the COVER in the
direction of the arrow and swinging it open on its hinge, as shown. Clean
battery terminals with: a rough cloth; then insert the battery with its positive
(+) terminal toward the center of the camera, as illustrated. Close the cover
by pressing it down firmly. until it locks.
IMPORTANT: Flash failure usually results from tarnish (often invisible) on camera and
battery contacts. Clean battery and camera contacts often with a rough, damp cloth.
If flash failure persists, install fresh batteries.
16
FLASHCUBES
e Set Flash Exposure Control—Rotate the SHUTTER-SPEED SCALE until the
FLASH SYMBOL clicks into place opposite the red INDEX DOT, as shown in
the illustration; then set the lens opening dial at f/22 and rotate the focusing
scale back and forth until the two scales are locked together. This coupling
automatically sets the correct lens opening as you focus the camera for
subject distances between 5 and 18 feet (indicated by blue band).
www.orphancameras.com
e Insert Flashcube—Insert a FLASHCUBE in
the flash socket on the top of the camera;
with one of the four bulbs facing forward,
press down the cube until it snaplocks in
place. The cube revolves V4 -turn each time
film is advanced for the next exposure,
thus providing flash for four exposures if
a fresh cube is in place. To remove a used
or partially used cube from the camera,
lift it out of the socket. When returning a
partially used cube to the camera, make
sure that a fresh bulb is facing forward
before the exposure is made. The flashcube
can be rotated manually in the direction of
the arrow.
18
e Set the Distance—Rotate the focusing scale until the orange number, rep-
resenting the subject distance in feet (between 5 and 18 feet, as indicated
by the blue band) is opposite its triangular index.
e Flash the Picture—Compose the picture within the luminous viewframe of
the finder, hold the camera steady, and press the shutter release slowly to
flash the bulb and take the picture.
Other Flash Sources
Your camera accepts:
1 Cordless-type flasholders with a center contact in the base, such as the
KODABLITZ Flasholder, slip into the shoe-type bracket on the top of the
camera. Set the shutter speed for 1/30 sec (30) and determine the lens
opening from the table on the flasholder or in the film instruction sheet.
2. Electronic flash equipment—Set the shutter speed from 1/30 to 1/250
sec. See instructions packed with your flash unit.
19
www.orphancameras.com
TIME EXPOSURES
If a subject needs a longer exposure time |
than 1/30 second, such as for night pic- a.
tures or other low-light situations, place
the camera on a firm support* and make a
time exposure. Rotate the shutter speed
scale until the letter “B” clicks into place
opposite the red index dot, as shown. Now
the shutter will remain open as long as the
shutter release 1s depressed. The exposure
time depends on the lens opening (f-num-
ber) used and the light available (do not
use symbol scale). To reduce camera
movement use a cable release attached to
the threaded socket in the underside of the
shutter release.
SETTING EXPOSURE COUNTER
If the exposure counter has not returned
to the diamond-shaped mark (*) for any
*A threaded tripod socket is located on the base
20 of the camera.
reason (such as removal from the camera of a partially exposed film maga-
zine, without rewinding), the counter must be reset manually, before
loading the camera again. Open the back cover of the camera, and with the
LOCK LEVER depressed, rotate the SPROCKET until the diamond mark (+)
is centered in the counter.
CARE OF THE CAMERA
Your KoDAK RETINA S1 Camera is a ruggedly built precision instrument.
For long service and quality performance, protect the camera from dust
and dirt and avoid rough handling. Use a rubber syringe to blow out any
dust that may be inside the camera. If the lens needs cleaning, first brush
or blow away any grit or dust. Wipe the surface gently with Kopak Lens
Cleaning Paper. If moisture is needed, use KoDAK Lens Cleaner.
Do not attempt to make any repairs or remove any parts from the shutter,
lens, or camera. Never oil the shutter or any parts of the camera. If you find
that service is necessary, see page 24.
21
www.orphancameras.com
PHOTO AIDS | .
KoDAK RETINA Field Case, Model K—This attractive, black, plush-lined case will provide
maximum protection for your camera. This case attaches to the camera by a snap
fastener, which fits a receptacle in the base of the camera. The fold-down front permits
instant picture-taking with the camera in its case. The case is supplied with a hand
strap, and an adjustable extension strap.
Adapter Ring, Series 5 (screw-in type) —Permits use of Series 5 filters and other lens
attachments.
KoDAK RETINA Lens Attachments (32mm)—For close and ultra-close pictures, the
KODAK RETINA Close-Up Lens Set N/32, and the Close Range and Viewfinder Kit Model C
are available. Filters for both black-and-white and color, and the KoDAK RETINA 32 Lens
Hood (to protect lens from extraneous light) can also be obtained from your photo
dealer.
KoDAK Flashcube Extender—Produces more pleasing modeling and shadow effects by
increasing the distance between the flashcube and the lens.
KoDAK Projectors—A KopAK projector or viewer will show your color slides big, bright
and sharp on the screen. Ask your dealer to see the low-cost KoDAK READYMATIC Viewer
or the popular KobAak CAROUSEL projectors.
Kopak Publications—Kopak Publications cover a wide range of subjects. Your dealer
will be glad to show you, for example, ‘How to Make Good Pictures’’—perhaps the
most popular picture-taking book of all time—and other inexpensive books on pho-
tography.
22
CAMERA FACTS
Film: Film Load—Kopak 135, 20- or 36-exposure magazines.
Negative Size—24mm x 36mm.
Lens: 45mm, f/2.8 Schneider REOMAR Lens. Openings—f/2.8, f/4, f/5.6, f/8, f/11,
f/16, f/22.
Shutter: Automatically cocks when film is advanced.
Speeds— 1/30, 1/60, 1/125, 1/250 second, plus “Flash” and “B”' setting.
Release—On front of camera, or KopAK Metal Cable Release No. 5. Double-exposure
prevention.
Flash Synchronization—Flashcubes at flash symbol; flashbulbs at 1/30 sec; electronic
flash at all speeds.
Daylight Exposure Control: Set by five lighting-condition symbols. For films with ASA
speeds 10 to 400.
— Automatic Flash Control: Correct lens opening set by focusing. ASA 10 to 400.
Battery —Uses one 5.6-volt mercury battery.
Focusing and Viewing: Focusing—Zone focusing (Close-ups, Groups, and Scenes) and
scale focusing 31, ft to Inf.
Viewfinder—Projected viewframe type with parallax marks. :
Rapid Wind Lever: Advances film and sets shutter with one stroke; rewinds film after
setting for rewind.
Photo Aids: An extensive line of specialized photo aids extends the picture- as scope
of your camera. See page 22 for partial listing.
23
">