تبلیغات
تبلیغات
Kodak
RETINETTE
“née à
KODAK RETINETTE IA CAMERA A
Your KODAK RETINETTE IA Camera is a distinguished member of the
long line of traditionally excellent RETINA cameras. There is a certain
pride of ownership that comes with this knowledge. Following are a few
of the many features of this easy-to-use camera.
e Quality f/2.8 45 mm lens with convenient “zone” focus settings.
e Versatile four-speed flash shutter with long-exposure and self-timer
settings.
e Clear, easy-to-use projected frame finder. o |
e Compaciness, combined with superb craftmanship éd attractive
styling.
Before taking any important pictures — on a trip or at a special event —
it is well to shoot a magazine of film outdoors, and indoors with flash.
This will give you practice in operating the camera and provide |
a check on your equipment.
2 ‘
Dre Meda ST ESA MN av
Picturetaking
ts as easy as this!
After loading the camera as
described on page 6, you...
1. Set the shutter-speed (a);
for example “60" (1/4 second).
2. Set the lens opening (b);
for example, “11”.
3. Set the distance (c);
for example 7 ("Groups").
... You are now ready to take
the picture. Read on for the
important details of camera
operation.
COLOR FILMS
| — | Рог color
largements can.
ight pictures and.
lachrome-X Film — For color transparencies for projectio
olor prints and enlargements can be made. The speed |
“more than 2% times faster and has higher contrast than
| Film above. Use Kodachrome-X Film for Daylight for
for flash pictures with blue bulbs. 20 or 36 exp
Im — For color transparencies for projection С
d enlargements can be made. Available in
res, and for flash pictures with blue bulb
BLACK-AND-WHITE FILMS
KODAK PANATOMIC-X Film — The
film to use for big enlargements
when high film speed is not a factor.
It combines exceptionally fine grain
and the ability to record extremely
fine detail. 20 or 36 exposures.
KODAK PLUS-X Pan Film — An ex-
cellent high-speed panchromatic
film for general outdoor and in-
terior use. The low graininess and
high resolving power permit high-
quality enlargements. 20 or 36 ex-
posures,
KODAK TRI-X Pan Film — An ex-
tremely fast panchromatic film of
moderate contrast, wide exposure
and development latitude, and color
sensitivity suitable for all types of
illumination, 20 or 36 exposures.
Loading — always in subdued light
1.
2.
3.
Press the opening button (d) in the camera base.
The camera back will spring open.
Pull the rewind knob (e) out as far as it will go.
Place the film magazine in the recess next to the
rewind knob. Push the rewind knob (e) all the way
in, turning it slightly if necessary.
Turn the built-in TAKE-UP SPOOL (f) by one of its
toothed flanges until a light-colored slot points up-
ward. With the lower edge of the film against the
lower take-up spool flange, push the film end pro-
truding from the magazine far enough into this slot
to ancher a perforation over the small pin. |
Turn the built-in take-up spool until the teeth of
‘the sprocket (g) engage the perforations ON BOTH
SIDES. Close the camera back by pressing the back
against the body until you hear it lock.
Turn the rewind knob (e) in the direction of the arrow
until a slight resistance is felt. This takes up the slack
film inside the magazine.
6
Setting the film counter
and film indicator
The film counter (left) tells you how many
exposures remain, Turn the black knurled
ring (h) counterclockwise until one of the
diamond marks is opposite the triangular
mark (for 36-exposure magazines set mark
between 1 and 36; for 20-exposure magazines
set mark to 23). Actuate the rapid wind lever
on the bottom of the camera, then press the
shutter release — for details see page 14.
Do this two more times to bring the counter
to 20 or 36 depending on the number of
exposures in your magazine. The rewind
knob's turning counterclockwise indicates pro-
er film advance.
o set the film indicator (left) hold the rewind
knob and turn the inner serrated disk until
the black dot points to the type of film loaded
in the camera:
“E = Black-and-white Film
COLOR XX = Daylight Color Film
8 COLOR «O: = Artificial-Light Color Film
Unloading -
always in subdued light
After the last exposure and before the back
of the camera is opened, the film must be
rewound into its magazine. To do this, press
the clutch button (i) in the camera base and
turn the rewind knob (e) in the direction of
the arrow until the clutch button ceases to
rotate. (Watch the black dot on the clutch
button.) Give a few more turns to draw the
film into the magazine; open the camera
back, pull out the rewind knob, and remove
the magazine.
Note: If the film counter was not set, or was
set incorrectly, the rapid wind lever may en-
counter resistance before the exposure counter
shows “1”. This indicates that the end of the
film has been reached. Do not force the wind
lever. Rewind the film and unload as described
above.
Setting
the shutter and
lens opening
To set the SHUTTER SPEED, turn the knurled
ring (a) until the red mark is opposite the
required shutter speed. The figure 30 stands
for 159 second; 60 for /4 second; 125 for
1/125 second and 250 for Yosy second. “B” is
the setting for time exposures of any length.
(See page 16.)
With average daylight pictures, use 1/49 or
1/95 second. For fast moving subjects, use
Vos second.
Set the LENS OPENING by moving the lens
opening lever (j) until the required lens
opening (f/number) is opposite the index (b).
In the illustration, the shutter is set at 1/4 sec-
ond, and the lens opening at f/8.
NOTE: Do not make. intermediate shutter speed settings.
Intermediate lens opening settings, however, can be
made.
DAYLIGHT EXPOSURE GUIDE FOR KODAK COLOR AND BLACK-AND-WHITE FILMS
For Average, Front-Lighted
2 Hours after Sunrise to 2 Hours before Sunset
Subjects in Daylight from
KODACHROME 11
KODA- KODACOLOR
LIGHT CONDITIONS CHROME-X EKTACHROME PLUS-X PAN
Lens Opening with Shutter Set at "60 (1/4 Sec.)
Bright or Hazy Sun (Distinct Shadows) 16 f/11 f/22
Cloudy Bright (No Shadows) f/8 f/5.6 f/11
Heavy Overcast or Open Shade | £5.6 и #4 #8
(Lighted by a large area of sky)
Use lower f/number for the following:
One f/number lower at shutter speed
1/15 second for action shots.
Two f/numbers lower at shutter
speed !/2 second for fast action.
One {/number lower for side-lighted
subjects.
Two f/numbers lower for back-
Use higher f/number for the following:
O One f/number higher at shutter
speed 1/3 second. Use only at low
light levels and for flash pictures.
O One f/number higher for bright sun
on sand or snow.
lighted close-up subjects.
NOTE: For other films and for additional exposure information consult the
instructions supplied with the film used
Focusing
Zone Focusing: You have a choice of three
zone focus or snapshot settings indicated by
symbols on the focusing scale.
Close-Ups (Close Range)
iM? Groups (Medium Range)
ZEN Scenes (Far Range)
Turn the knurled lens ring (k) until the symbol
corresponding to the type of subject is oppo-
site of the triangular mark.
Scale focusing: You can also focus the
camera for the correct distance by setting
the black or red figures opposite the 4 tri-
angular mark.
NOTE: The red figures on the focusing scale indicate
“feet” and the black figures “meters” (m).
12
Using the viewfinder
Hold the camera in the picturetaking position and look through the eye-
piece of the viewfinder. With your eye close to the finder opening, you
will then see the subject outlined by the luminous view-frame. See illus-
tration below. Depending on the subject, you may view the picture with
the camera held in either the horizontal or the vertical position. The two
illustrations on this page are shown as examples.
Hold the camera steady while taking the picture, and make sure that
no part of your field case or other obstruction is in front of the lens.
Setting
and releasing shutter
If the shutter is not set, pressing the
EXPOSURE RELEASE (1) will not trip the
shutter. To set the shutter, with the right
thumb swing out the RAPID WIND LEVER
(m) in one movement as far as it will go;
then let it return to its original position.
Swinging out this lever sets the shutter and
advances the film by one frame at the same
time. Press down the exposure release (1)
all the way with a slow, squeezing action.
If the rapid wind lever (m) becomes locked,
this means either that the exposure has not
been made or that the end of the film has
been reached.
14
Flash pictures
Attaching Flasholder: Cordless flasholders
with center contact in the base — slide into
accessory “shoe” (n) on top of the camera.
The other contact is part of the shoe.
Y Flasholders with connecting cords, such as
| the Kodak Ektamite Flasholder, slide into the
accessory shoe (n). Insert the cord tip into
flash socket (0) on the camera.
Setting Exposure: Use only a shutter speed
of 7, second, by turning red mark on ring
to “30°. (With electronic flash, any shutter
speed up to ls, second can be used.) The
lens opening is determined by means of a
flash guide number which is specified in the
instructions packed with the film. To deter-
mine the proper lens opening divide the à E.
guide number by the flash-to-subject distance. Me tad -
Example: 56 :
Guide Number 110
Flash-to-subject distance 10 feet
A
Li
= Lens opening f/11
Self-timer
First set the shutter by the rapid wind lever,
and then slide the lever marked in red (p)
clockwise as far as it will go. If you then
depress the release button, the shutter will
not be released until after about 10 seconds.
Once the self-timer has been set, the follow-
ing picture must be taken with the self-timer.
The self-timer action can be used for flash.
Time exposures
Turn the shutter speed ring (a) until the red
mark is opposite the letter “B”. The shutter
remains open as long as the exposure release
is depressed. The exposure time varies ac-
cording to the lens opening used, and the
light available.
Time exposures should be made with a tripod
or other firm support. Attach the camera to
the tripod by the tripod socket on the base
of the camera. The use of a cable release
which screws into the exposure release button
is also suggested.
Close-ups between 3.3 and 8 feet
When taking pictures of a subject between
3.3 and 8 feet, the field of view outlined by
the luminous frame in the viewfinder does
not show what will actually appear in the
final picture because the finder and lens do
not see the same view at close distances.
This is called parallax. To compensate for
such parallax at a distance of 3.3 feet, the
subject must be seen below an imaginary line,
drawn between the two opposite pointers
near the top of the viewframe (dotted in the
illustration). With subjects farther away than
3.3 feet, this imaginary line gradually moves
up until, at 8 feet, it coincides with the view-
frame. An equivalent area eliminated at the
top of the frame is added to the bottom of
the frame.
.
НН
e
E.
ii A
How to determine depth of field
A depth-of field scale (q), composed of indicator lines and numbers
corresponding to lens openings, is arranged on either side of the focus
index. The end lines of the bracket indicate the depth of field at f/4.
The depth of field increases beyond these limits with each smaller lens
opening down to f/22.
On the scale (q) the lens opening numbers 5.6 and 2.8 are indicated by
the small lines on either side of
the bracket limit marks.
Suppose you have set the lens
opening ct f 11 and the distance
at 4% iGroups); you can now
read off cbout 6 ft. at the left
and about infinity (=) at the right,
opposite the two figures “11”
on the depth-of-field scale (q).
Everything wiil be in focus with-
in the rence.
Depth of field
18
Care of the Camera
Your KODAK RETINETTE IA Camera is ruggedly built, but
it is a fine precision instrument; so protect it from dust and
dirt and avoid rough handling. Use a rubber syringe to
blow out any dust that may be inside the camera. If the
lens needs cleaning, first brush or blow away any grit or
dust. Wipe the surface gently with KODAK Lens Cleaning
Paper. If moisture is needed, use KODAK Lens Cleaner.
Do not attempt to make any repairs or remove any parts
from the shutter, lens, or camera. Never oil the shutter
or any parts of the camera. If you find that service is
necessary, return the camera to your KODAK dealer, who
will have repairs made locally, or send it to KODAK.
19
Avoid these:
1.
20
Camera Movement: The whole picture is blurred. Н happens when you
“punch” the shutter release. Stand steady; and release the shutter
with a slow, squeezing action.
Subject Movement: Produces a different effect from camera move-
ment — everything but your subject is sharp. Use !/125 Or ‘asp second
shutter speed setting for fast-moving subjects.
Dirty Lens: Your camera can't see through a dirty lens. Keep it clean;
it pays. Use KODAK Lens Cleaning Paper and KODAK Lens Cleaner.
Cluttered Backgrounds: Trees, wires, poles — steal interest from the
subject. Look beyond the subject before you shoot; if background is
distracting, change camera position, or move the subject.
Subject Out of Focus: You get fuzzy pictures when the camera is too
close to the subject or if you have the wrong distance setting.
Lens Obscured: You'll get a picture like this if your case strap is in
front of the lens. Learn to handle your camera so that your fingers
or other objects don't get in front of the lens.
Photo aids
Kodak Retinette Field Case — Leather with chrome-finished reinforcement.
Adjustable neck strap. Protects your camera.
Kodak Ektamite Flasholder (with connecting cord) — Small, light and
handy. Accepts AG-1-type bulbs. Slides easily into accessory shoe on top
of camera.
Lens Attachments — Kodak Retina Filters (screw-in type) 32 mm diameter.
Kodak Retina 45F Lens Hood. Kodak Adapter Ring 629 A for use of
Series 6 Lens Attachments such as Filters, Lens Hoods, Close-Up Lenses.
Kodak Supermatic 500 Projector — New remote focusing — remote slide
changing and instant editing — in this handsome, rugged, compact self-
cased, 500-watt projector. Holds up to 36 cardboard slides at one loading.
See your dealer for this or a choice of other Kodak slide projectors.
22
KODAK RETINETTE | A facts
Film: Film Load — Kodak 135, 20- or 36-exposure magazines.
— Negative Size — 24x 36 mm.
Lens: 45 mm f/2.8 Schneider Reomar. Lens Openings — f/2.8, f/4, f/5.6,
f/8, f/11, f/16, f/22.
Shutter: Prontor 250 S — Automatically cocked when film is advanced.
Speeds — Yao, '/607 125, Vaso second and “B”.
Release — Plunger type on top of camera or Kodak Metal Cable
Release No. 5.
Flash — Built-in synchronization for class F and M bulbs at 14, sec., and
electronic flash at all speeds. Two flash outlets: Flash socket for
continental cord tip; center contact in accessory shoe.
Focusing and Viewing: Focusing — Zone focusing (Close-Ups, Groups,
and Scenes) and scale focusing (3.3 feet to infinity)
Viewfinder — Projected viewframe type.
Rapid Wind Lever: Advances film and sets shutter with one stroke.
Double-exposure prevention.
Construction: Body — Die cast aluminum alloy; black covering;
chrome top and trim; tripod socket in camera base.
23
">
/
دانلود
فقط یک یادآوری دوستانه. می توانید سند را درست در اینجا مشاهده کنید. اما مهمتر از همه، هوش مصنوعی ما قبلاً آن را خوانده است. این می تواند موارد پیچیده را به زبان ساده توضیح دهد، به سوالات شما به هر زبانی پاسخ دهد و به شما کمک کند به سرعت حتی طولانی ترین یا پیچیده ترین اسناد را پیمایش کنید.
تبلیغات