Shimano ST-EF33 Shifting/Brake Lever Service Instructions

 = 4, Pass the inner cable through the inner cable lead, and after setting
Installation of the V-brake so that the total of the clearances between the left and right shoes
A WARNING Insert the stopper pin of the brake body into the center spring hole and the rim is 2 mm, tighten the cable fixing boit.
® №15 important to completely understand the operation of " in the frame mounting boss, and then secure the brake body to the Tightening torque:
your bicycle's brake system. Improper use of your bicycle's frame with the link fixing boit. 6 - 8 NM (52 — 69 in. Ibs.)
brake system may result in a loss of control or an accident, +
which could lead to severe injury. Because each bicycle
may handle differently, be sure to learn the proper braking
technique (including brake lever pressure and bicycle
control characteristics) and operation of your bicycle. This
can be done by consulting your professional bicycle dealer
and the bicycle's owners manual, and by practicing your
riding and braking technique.
* Use the BR-M330 V-brake with V-brake-
compatible brake levers such as the ST-
EF33 / BL-MC40 brake levers.
+—— [nner cable lead 5 mm Allen key
\
Des SERN =r
Tightening torque:
5 — 7 Nm {43 - 61 in. Ibs.}
5 mm Allen key
SERVICE INSTRUCTIONS SI-B610B
Spring hole
Brake System
2, While holding the shoe against the rim, adjust the amount of shoe
protrusion by changing over the washer B (6 mm or 3 mm) so that
Before use, read these instructions carefully, and follow them for correct use.
dimension A is kept at 39 mm or more.
In order to realize the best performance, we recommend that the fol- |
lowing combination be used. : ;
Spring tension Spring tension
Series ACERA adjustment screw adjusiment screw
Brake lever ST-EF33 |
V-brake BR-M330
Brake cable O QUe Mover == == ==
© v e
NOTE:
For any questions regarding methods of handling or maintenance,
Depress the brake lever about 10 times as far as the grip and
please contact the place of purchase.
" check that everything is operating correctly and that the shoe
clearance is correct before using the brakes.
3 mm washer B 6 mm washer B
Installation of the brake lever | | T fixing nut
Depress about
Use a 5 mm Allen key to install the brake lever. 1 т
10 times
=m EHD
Use a handlebar grip with a maximum Je к
outer diameter of 32 mm. |
Washer
Washer A | Washer A
Tightening torque: Shoe fixing link
6-8 Nm {52 - 69 in. Ibs.}
3. White holding the shoe against the rim, tighten the shoe fixing nut.
+——— 5 mm Allen key
These service instructions explain how to use and maintain the
e—— 5 mm Allen key Shimano bicycle paris which have been used on your new bicycle.
For any questions regarding your bicycle or other matters which are
not related to Shimano parts, please contact the place of purchase
or the bicycle manufacturer.
Please nole: Specilicalions are subject to change for improvement wilhout notice. (English)
Tightening torque: o
6-sNm(52-60in.15s} ) SUIMANO* Td BE
SHIMANO AMERICAN CORPORATION
One Holland Irvine CA 82618 U,S A. Phone 943-851-5003
+ SHIMANO EUROPA
Induslrieweg 24 NL-8071 CT Nunspeet Holland Phone 31-3412-72222
SHIMANO Inc.
3-77 Oimalsucho, Sakai, Osaka, Japan Phone 0722-23-3243
© Aug. 1998 by Shimano Inc. PIT. IZM. Printed in Malaysia