Shimano TL-FC39 Dealer's Manual 132 Pages
Shimano TL-FC39 Dealer's Manual
Shimano TL-FC39 is a professional tool designed to install and remove the bottom bracket cups of Hollowtech II type. It has a long handle for increased leverage and a wide, ergonomic grip for comfort and control.
advertisement
(English)
ROAD
City Touring/
Comfort Bike
DM-E8000-10
MTB
URBAN SPORT
Dealer's Manual
Trekking
E-BIKE
SC-E8000
SC-E6100
SC-E7000
SC-E6010
EW-EN100
SW-E6010-L
SW-E7000-L
SW-E8000-L
SW-M8050-L
SW-M9050-L
SW-E6010-R
SW-E7000-R
SW-M8050-R
SW-M9050-R
RD-M9050
RD-M8050
FC-E8000
FC-E8050
FC-M8050
SM-CRE80
SM-CRE80-B
SM-CRE80-12-B
SM-CDE80
E8000 Series
DU-E8000
SM-DUE10
SM-DUE11
SM-DUE80-A
SM-DUE80-B
BT-E8010
BT-E8020
BM-E8010
BM-E8020
RT-EM300
RT-EM600
RT-EM800
RT-EM810
RT-EM900
RT-EM910
CONTENTS
IMPORTANT NOTICE ........................................................................................................... v
TO ENSURE SAFETY ........................................................................................................... vi
Chapter1 LIST OF TOOLS TO BE USED 1-1
LIST OF TOOLS TO BE USED ............................................................................................1-2
Chapter2 INSTALLATION 2-1
INSTALLATION ..................................................................................................................2-2
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT 3-1
INSTALLING AND WIRING THE DRIVE UNIT ...................................................................3-2
ii
Chapter4 CHARGING THE BATTERY 4-1
CHARGING THE BATTERY ................................................................................................4-2
Chapter5 HOW TO OPERATE 5-1
HOW TO OPERATE ...........................................................................................................5-2
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES 6-1
CONNECTION AND COMMUNICATION WITH DEVICES .................................................6-2
iii
Chapter7 MAINTENANCE 7-1
MAINTENANCE ................................................................................................................7-2
iv
IMPORTANT NOTICE
IMPORTANT NOTICE
•
This dealer's manual is intended primarily for use by professional bicycle mechanics.
Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer's manuals.
If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local bicycle dealer for their assistance.
• Make sure to read all owner's manuals included with the product.
• Do not disassemble or modify the product other than as stated in the information contained in this dealer’s manual.
• All manuals and technical documents are accessible online at https://si.shimano.com.
• For consumers who do not have easy access to the internet, please contact a SHIMANO distributor or any of the SHIMANO offices to obtain a hardcopy of the User's Manual.
• Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a dealer.
• The Bluetooth
®
word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by SHIMANO INC. is under license. Other trademarks and trade names are those of their respective owners.
For safety, be sure to read this dealer’s manual thoroughly before use, and follow it for correct use.
The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
Failure to follow the instructions could result in death or serious injury.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
v
TO ENSURE SAFETY
TO ENSURE SAFETY
DANGER
Be sure to also inform users of the following:
Handling the battery
• Do not deform, modify, disassemble or apply solder directly to the battery. Doing so may cause leakage, overheating, bursting, or ignition of the battery.
• Do not leave the battery near sources of heat such as heaters. Do not heat the battery or throw it into a fire. Doing so may cause bursting or ignition of the battery.
• Do not subject the battery to strong shocks or throw it. If this is not observed, overheating, bursting, or fire may occur.
• Do not place the battery into fresh water or sea water, and do not allow the battery terminals to get wet. Doing so may cause overheating, bursting, or ignition of the battery.
• Use the specified battery charger for charging and observe the specified charging conditions. Doing otherwise may cause overheating, bursting, or ignition.
WARNING
•
Be sure to follow the instructions provided in the manuals when installing the product.
It is recommended that you use only genuine SHIMANO parts. If parts such as bolts and nuts become loose or damaged, the bicycle may suddenly fall over, which may cause serious injury.
In addition, if adjustments are not carried out correctly, problems may occur, and the bicycle may suddenly fall over, which may cause serious injury.
• Wear approved eye protection while performing maintenance tasks such as replacing components.
• For information on products not explained in this manual, refer to the manuals provided with each product and store them so that they can be referenced at any time.
Be sure to also inform users of the following:
• Be careful not to let yourself be distracted by the cycle computer display while riding the bicycle. Otherwise, you may fall off the bicycle.
• Before riding, check that the wheels are secured. Otherwise, you may fall off the bicycle and be seriously injured.
• Be sufficiently familiar with how to start the power assisted bicycle before riding on busy streets. Otherwise, you may start the bicycle abruptly and have an accident.
• Make sure that the light is on when riding.
• Do not disassemble the product. Disassembling it may cause injury to persons.
• When charging the battery while it is installed on the bicycle, do not move the bicycle. The battery charger’s power plug may not be completely inserted into the outlet, which may lead to fire.
• Do not inadvertently touch the drive unit when it has been continuously used for a long period of time. The surface of the drive unit becomes hot and could cause burns.
vi
TO ENSURE SAFETY
Lithium Ion Battery
• If any liquid leaking from the battery gets into your eyes, immediately wash the affected area thoroughly with clean water such as tap water without rubbing your eyes, and seek medical attention immediately. If this is not done, the battery liquid may damage your eyes.
• Do not recharge the battery in very humid places or the outdoors. If this is not observed, electric shocks may result.
• Do not insert or remove the plug while it is wet. If this is not observed, electric shocks may result. If there is water leaking out of the plug, dry it thoroughly before inserting it.
• If the battery does not become fully charged even 2 hours after the designated charging time, immediately unplug the battery from the outlet and contact the place of purchase. Doing otherwise may cause overheating, bursting, or ignition of the battery.
• Do not use the battery if it has any noticeable scratches or other external damage. Doing so may cause bursting, overheating or problems with operation.
• The operating temperature ranges for the battery are given below. Do not use the battery in temperatures outside these ranges. If the battery is used or stored in temperatures outside these ranges, fire, injury or problems with operation may occur.
1. During discharge: –10 °C - 50 °C
2. During charging: 0 °C - 40 °C
Items related to installation to and maintenance of the bicycle
• Be sure to remove the battery and charger before wiring or attaching parts to the bicycle. Otherwise, an electric shock may result.
• Clean the chain with an appropriate chain cleaner regularly.
Intervals between maintenance depend on the use and riding circumstances. Never use alkali based or acid based solvents, such as rust cleaners. If these solvents are used the chain might break and cause serious injury.
CAUTION
Be sure to also inform users of the following:
• Observe the instructions in the user's manual for the bicycle in order to ride safely.
• Periodically check the battery charger and adapter, particularly the cord, plug, and case, for any damage. If the charger or adapter is broken, do not use it until it has been repaired.
• Use the product under the direction of a safety supervisor or the directions for use. Do not allow physically, sensory, or mentally impaired persons, inexperienced persons, or persons with no required knowledge including children to use this instrument.
• Do not allow children to play near the product.
• If any malfunction or trouble occurs, consult the place of purchase.
• Never modify the system. This may cause a malfunction in the system.
Lithium Ion Battery
• Do not leave the battery in a place exposed to direct sunlight, inside a vehicle on a hot day, or other hot places. This may result in battery leakage.
• If any leaked fluid gets on your skin or clothes, wash it off immediately with clean water. Otherwise, the leaked fluid may damage your skin.
• Store the battery in a safe place out of the reach of infants and pets.
vii
TO ENSURE SAFETY
NOTICE
Be sure to also inform users of the following:
• Be sure to attach dummy plugs to any unused ports.
• For installation and adjustment of the product, consult a dealer.
• The units are designed to be fully waterproof to withstand wet weather riding conditions. However, do not deliberately place them into water.
• Do not clean the bicycle with a high-pressure washer. If water gets into any of the components, operating problems or rusting may result.
• Handle the components carefully, and avoid subjecting them to any strong shocks.
• Do not place the bicycle upside down. Doing so may damage the cycle computer or shift switch.
• Although the bicycle still functions as a normal bicycle even when the battery is removed, the light does not turn on if it is connected to the electric power system. Be aware that using the bicycle under these conditions will be considered non-observance of the road traffic laws in Germany.
• When carrying the bicycle in a car, remove the battery from the bicycle and place it on a stable surface in the car.
• Before connecting the battery, make sure that there is no buildup of water or dirt in the connector where the battery will be connected.
• When charging the battery while it is mounted on the bicycle, be careful of the following:
- When charging, make sure there is no water on the charging port or the charger plug.
- Check that the battery mount is locked before charging.
- Do not remove the battery from the battery mount while charging.
- Do not ride the bicycle with the battery charger mounted on.
- Close the charging port cap when not charging.
- Stabilize the bicycle to ensure that it does not collapse during charging.
• It is recommended to use a SHIMANO genuine battery. If using a battery from another company, be sure to read the product manual thoroughly prior to use.
• Some of the important information in this dealer's manual can also be found on the device labels.
• The number found on the battery key is necessary when purchasing spare keys. Store it carefully.
• Use a damp, well wrung out cloth when cleaning the battery and plastic cover.
• If you have any questions about the use and maintenance of the product, consult the dealer where you made the purchase.
• Contact the place of purchase for updates to the component software. The most up-to-date information is available on the SHIMANO website. For details, refer to the "CONNECTION AND COMMUNICATION WITH DEVICES" section.
• Products are not guaranteed against natural wear and deterioration from normal use and aging.
• For maximum performance we highly recommend SHIMANO lubricants and maintenance products.
Connection and communication with PC
A PC linkage device can be used to connect a PC to the bicycle (system or components), and E-TUBE PROJECT can be used to carry out tasks such as customizing single components or the whole system and updating firmware.
• PC linkage device: SM-PCE1 / SM-PCE02
• E-TUBE PROJECT: PC application
• Firmware: software inside each component
Connection and communication with smartphone or tablet
It is possible to customize single components or the entire system, and update firmware, using E-TUBE PROJECT for smartphones/tablets after connecting the bicycle (system or components) to a smartphone or tablet via Bluetooth LE.
• E-TUBE PROJECT: app for smartphones/tablets
• Firmware: software inside each component
viii
TO ENSURE SAFETY
Lithium Ion Battery
Disposal information for countries outside the European Union
This symbol is only valid within the European Union.
Follow local regulations when disposing of used batteries. If you are not sure, consult the place of purchase or a bicycle dealer.
Items related to installation to and maintenance of the bicycle
• Do not use thinner or other solvents to clean any of the components. Such substances may damage the surfaces.
• You should periodically wash the chainring unit with a neutral detergent. In addition, cleaning the chain with a neutral detergent and lubricating it can be an effective way of extending the useful life of the chainring unit and the chain.
The actual product may differ from illustrations, as this manual is intended chiefly to explain the procedures for using the product.
ix
Chapter1 LIST OF TOOLS TO BE USED
Chapter1 LIST OF TOOLS TO BE USED
LIST OF TOOLS TO BE USED
The following tools are needed for installation, adjustment, and maintenance purposes.
Component
Cycle computers
(SC-E8000)
Where to use
Clamp bolt
Handlebar fixing bolt
Cycle computers
(SC-E6010)
Cycle computers
(SC-E6100)
Angle adjustment screw
Clamp bolt
Mounting bolt
Angle adjustment bolt
Clamp bolt
Cycle computers
(SC-E7000)
Case fixing bolt
Assist switch
(SW-M9050/SW-E8000)
Assist switch
(SW-E6010/SW-E7000)
Electric wire
Unit fixing bolt
Lever fixing bolt
Fixing bolt
Connector
Mount lower case
Battery mount
(BM-E8010)
Key unit
Key unit cover
Mount upper case
Tool
3 mm hexagon wrench
Screwdriver [#2]
Screwdriver [#2]
Screwdriver [#2]
3 mm hexagon wrench
2.5 mm hexagon wrench
3 mm hexagon wrench
2 mm hexagon wrench
3 mm hexagon wrench
TL-EW02
3 mm hexagon wrench / 8 mm spanner
3 mm hexagon wrench
2.5 mm hexagon wrench
2.5 mm hexagon wrench
1-2
Chapter1 LIST OF TOOLS TO BE USED
Component
Battery mount
(BM-E8020)
Speed sensor
(SM-DUE10)
Speed sensor
(SM-DUE11)
Magnet unit
Light cable
Drive unit
Crank arm
Chain device
Clamp band
Where to use
Mount lower case
Mount upper case
Key cylinder
Key unit
Key unit cover
Speed sensor fixing bolt
Speed sensor fixing bolt
Fixing bolt
Mounting bolt
Drive unit fixing bolt (M8)
Cover fixing bolt (M3)
Cap
Stopper plate
Guide fixing bolt (M5)
Back plate fixing bolt (M6)
Clamp band
-
Tool
5 mm hexagon wrench
Screwdriver [#2]
2 mm hexagon wrench
5 mm hexagon wrench
Screwdriver [#2]
4 mm hexagon wrench
Hexalobular [#25]
Hexalobular [#10]
Screwdriver [#2]
Screwdriver [#2]
-
Screwdriver [#2]
TL-FC16/TL-FC18
5 mm hexagon wrench
3 mm hexagon wrench / 4 mm hexagon wrench
3 mm hexagon wrench
2.5 mm hexagon wrench
1-3
Chapter1 LIST OF TOOLS TO BE USED
Component
Chainring unit
Chain guard
Where to use
Lock ring
Chainring
Chain guard fixing bolt
Tool
TL-FC39+TL-FC36
TL-FC22+TL-FC23
Screwdriver [#2]
1-4
Chapter2 INSTALLATION
Chapter2 INSTALLATION
Names of parts
INSTALLATION
Names of parts
(H)
(F)
(N)
(G)
(P) (O) (O)
(J)
(D) (I)
(C)
(E)
(B)
(L)
(A)
(M)
(K)
(A)
Cycle computer/Junction [A]:
SC-E8000/SC-E6010/SC-E6100/
SC-E7000/EW-EN100
(B)
Assist switch:
SW-E8000-L/SW-E6010/SW-E7000
(C)
Chainring unit:
SM-CRE80/SM-CRE80-B/
SM-CRE80-12-B
(D)
Chain device:
SM-CDE80
(E)
Crank arm:
FC-E8000/FC-E8050/FC-M8050
(F)
Drive unit:
DU-E8000
(G)
Speed sensor:
SM-DUE10
(H)
Drive unit cover:
SM-DUE80-A
(type that covers drive unit ports)
SM-DUE80-B
(type that covers drive unit ports and the frame installation bolts)
(I)
Battery (external type)/
Battery mount (external type):
BT-E8010/BM-E8010
(J)
Battery charger:
EC-E6000
(K)
Battery (built-in type)/
Battery mount (built-in type):
BT-E8020/BM-E8020
(L)
Electric wire: EW-SD50
When using electronic gear shifting
(M)
Shifting switch:
SW-M9050-R/SW-M8050-R/
SW-E6010/SW-E7000
(N)
Rear derailleur (DI2):
RD-M9050/RD-M8050
(O)
Speed sensor:
SM-DUE11
(P)
Disc brake rotor:
RT-EM300/RT-EM600/RT-EM800/
RT-EM810/RT-EM900/RT-EM910
TECH TIPS
Maximum cable length (EW-SD50)
(L)
≤ 1,600 mm
2-2
Chapter2 INSTALLATION
Product specifications
Product specifications
Operating temperature range:
During discharge
Operating temperature range:
During charging
Storage temperature
Storage temperature (Battery)
Charging voltage
Charging time
-10 - 50 °C
0 - 40 °C
Battery type
Nominal capacity
-20 - 70 °C
-20 - 60 °C
100 - 240 V AC
Refer to the SHIMANO STEPS special battery and parts user's manual. For the latest information on manuals, see the website (
https://si.shimano.
com
).
Rated voltage
Drive unit type
Motor type
Rated drive unit power
Lithium Ion Battery
Refer to the SHIMANO STEPS special battery and parts user's manual. For the latest information on manuals, see the website (
https://si.shimano.
com
).
36 V DC
Midship
Brush-less DC
250 W
* The maximum speed up to which power assistance is provided is set by the manufacturer and is conditional on where the bicycle is to be used.
2-3
Chapter2 INSTALLATION
Installing and removing the cycle computer (SC-E8000/SC-E7000)
Installing and removing the cycle computer (SC-E8000/SC-E7000)
The example shown here is for SC-E8000
(A)
Pass the clamp band on the cycle computer over the handlebar.
< SC-E7000 >
An adapter is required for 25.4 mm diameter handlebars.
(A)
Clamp band
(B)
Cycle computer
(C)
Adapter
1
(B)
When installing SC-E7000 on 25.4 mm diameter handlebars
(A)
(C)
(B)
To be continued on next page
2-4
Chapter2 INSTALLATION
Installing and removing the cycle computer (SC-E8000/SC-E7000)
Adjust the angle of the cycle computer so that it is easy to see, and then use a
3 mm hexagon wrench to tighten the clamp bolt.
(A)
(A)
Clamp bolt
Tightening torque
0.8 N·m
NOTICE
Recommended installation angle of the information display: Between 15° to 35° to the horizontal.
2
35°
15°
TECH TIPS
When removing the cycle computer, reverse the procedure.
2-5
Chapter2 INSTALLATION
Installing and removing the cycle computer (SC-E6010/SC-E6100)
Installing and removing the cycle computer (SC-E6010/SC-E6100)
Installation
1
Push the clamp area
(B)
open, and then install the bracket to the center of the handlebar.
(B)
< SC-E6010 >
Use the clamp bolt
(A)
to secure the clamp part
(B)
to the handlebar.
< SC-E6100 >
Use the clamp bolt
(A)
to temporarily install the clamp part
(B)
to the handlebar.
(A)
(C)
2
(A)
Clamp bolt
(B)
Clamp part
(C)
Adapter
Handlebar compatibility table
øA
ø23.4 - ø24
ø24 - ø25.5
ø31.3 - ø31.9
øB-øA
0 - 1.1
0 - 1.1
0 - 0.6
Adapter
X
X
-
Fixing bolt
15.5 mm
20 mm
20 mm
* X: Necessary
Handlebar
30
25
< SC-E6010 >
Tightening torque
1 N·m
(A)
Slide the cycle computer
(A)
into the bracket
(B)
as shown in the illustration.
Insert it firmly until you hear it click.
< SC-E6010 >
This completes the installation.
< SC-E6100 >
Proceed to step 4.
(A)
Cycle computer
(B)
Bracket
3
(B)
To be continued on next page
2-6
Chapter2 INSTALLATION
Installing and removing the cycle computer (SC-E6010/SC-E6100)
(A)
Secure the cycle computer if necessary.
If the cycle computer will not be secured to the bracket, this step is not necessary.
Stand the cycle computer and bracket up on the stem (as though you are turning the cycle computer around).
Insert the square nut into the bracket and tighten the mounting bolt.
4
(B)
(A)
Square nut
(B)
Mounting bolt
Tightening torque
0.4 - 0.5 N·m
TECH TIPS
•
This procedure is used to secure the cycle computer to the bracket, so that it cannot be easily removed. This is useful for displaying the product.
•
Ask the user if they will secure the cycle computer when the product is delivered. If necessary, explain how to do so (as described to the left).
5
(A)
Return the cycle computer to its installation position if the cycle computer was stood up on the stem in step 4.
Then secure the bracket.
(A)
Clamp bolt
Tightening torque
1 N·m
Removal
1
(B)
(A)
< SC-E6010 >
This step is not necessary. Skip to step 2.
< SC-E6100 >
If the cycle computer was not secured, this procedure is not necessary. Skip to step 2.
Loosen the clamp bolt, and then stand the cycle computer and bracket up on the stem (as though you are turning the cycle computer around).
Then remove the mounting bolt and square nut.
(A)
Square Nut
(B)
Mounting bolt
(C)
Clamp bolt
(C)
To be continued on next page
2-7
Chapter2 INSTALLATION
Adjusting the angle of the cycle computer (SC-E6010/SC-E6100)
To remove the cycle computer, slide it while pushing the bracket lever
(A)
.
2
(A)
(A)
Lever
Adjusting the angle of the cycle computer (SC-E6010/SC-E6100)
Loosen the angle adjustment screw
(A)
with a screwdriver. Adjust the angle of the cycle computer to make it easier to see while riding.
After determining the angle, tighten the screw to the designated torque.
(A)
Angle adjustment screw
Tightening torque
0.5 N·m
(A)
Installing junction [A] (EW-EN100)
EW-EN100 is junction [A] with simple operation/display functionality.
Instead of a cycle computer, install it in a location around the cockpit from which the LED can be seen while riding.
This section explains how to install it to the brake hose. It can be installed to the brake outer casing using the same procedure.
NOTICE
EW-EN100 Installation location.
•
As shown in the figure, install EW-EN100 so that it does not reach the side of the frame. Otherwise, it could be damaged if the bicycle tips over and it is pinched between the frame and curb.
2-8
Chapter2 INSTALLATION
Installing junction [A] (EW-EN100)
(A)
1
(B)
2
EW-EN100
Open up the adapter and set it to the brake hose.
(A)
Adapter
(B)
Brake hose or brake outer casing
Bend the adapter along the brake hose.
(A)
Inner side
3
(B)
(A)
(A)
As shown in the figure, set EW-EN100 and then connect the electric wire or dummy plug.
(A)
Dummy plug
(B)
Electric wire
NOTICE
Be sure to connect either an electric wire or a dummy plug to the two E-TUBE ports on
EW-EN100. Connecting both will secure
EW-EN100 to the brake hose or brake outer casing.
TECH TIPS
When removing it, reverse the procedure.
2-9
Chapter2 INSTALLATION
Installing the switch unit
Installing the switch unit
SC-E8000
(B) (A)
1
2
3
[X]
[Y]
(A)
(A)
Pass the switch unit over the handlebar.
(A)
Handlebar
(B)
Switch unit
TECH TIPS
Supported handlebars:
Ø22.0 mm/Ø22.2 mm/Ø22.5 mm
Adjust the attachment position and angle, and then use a hexagon wrench to tighten the unit fixing bolt.
Adjust the positions of lever
[X]
and lever
[Y]
.
Loosen the lever fixing bolt using an
2 mm hexagon wrench, and adjust the lever's position so that it is easy to push.
After determining the position, tighten to the designated torque.
(A)
Unit fixing bolt
Tightening torque
2 - 2.2 N·m
NOTICE
Attach the lever in a position where it will not touch the brake lever when pushed all the way in.
(A)
Lever fixing bolt
Tightening torque
0.5 - 0.7 N·m
2-10
Chapter2 INSTALLATION
Installing the switch unit
SW-E6010
1
(A)
2
3
Temporarily attach the cable band
(A)
to the assist switch. Adjust the cable band according to the length of the handlebar.
(A)
Cable band
TECH TIPS
Cable bands are included with the SW-E6010.
Attach the assist switch mounted with the cable band to the handlebar.
(B)
(A)
Attach the assist switch to a ø 22.2 handlebar with the electric wire routed under the switch and open the fixing bolt cover
(A)
.
(A)
Fixing bolt cover
(B)
Fixing bolt
4
Tighten the fixing bolt
(B)
to the specified tightening torque using a 3 mm hexagon wrench.
Tightening torque
1.5 N·m
TECH TIPS
When removing the cycle computer, reverse the procedure.
2-11
Chapter2 INSTALLATION
Installing the switch unit
SW-E7000
1
2
3
Temporarily attach the cable band
(A)
to the assist switch. Adjust the cable band according to the length of the handlebar.
(A)
Cable band
TECH TIPS
Cable bands are included with the SW-E7000.
(A)
Attach the assist switch mounted with the cable band to the handlebar.
For a Ø22.0 to Ø22.4 handlebar, the electric wire must be facing downward.
(A)
Tighten the mounting bolt
(A)
to the specified tightening torque using a 3 mm hexagon wrench.
(A)
Mounting bolt
Tightening torque
1.5 N·m
TECH TIPS
When removing the cycle computer, reverse the procedure.
2-12
Chapter2 INSTALLATION
Connecting the electric wire
Connecting the electric wire
Set so that the projection on the connector is aligned with the groove in the narrow end.
(B)
(A)
(A)
TL-EW02
(B)
Plug
NOTICE
•
Use the SHIMANO original tool for installation and removal of the electric wire.
•
When installing the electric wire, do not forcibly bend the plug.
It may result in a poor contact.
•
When connecting the electric wire, push it in until it clicks in place.
Connect the electric wire to the switch unit (SW-E6010/SW-E7000)
Remove the cable cap from the switch unit.
1
(A)
(A)
Cable cap
2
(B) (A)
Pass the electric wire through the cable cap, and connect it to the switch unit.
(A)
Cable cap
(B)
Electric wire
NOTICE
Make sure the electric wire is connected through the cable cap. If the wire is not passed through the cable cap, the electric wire connector may be damaged.
To be continued on next page
2-13
Chapter2 INSTALLATION
Connecting the electric wire
When routing the electric wire in the direction of the stem
Install the cable cap.
When routing the electric wire along a cable built-in handlebar, run the wire along the guide of the cable cap then the handlebar.
(A)
Guide
3
When using a cable built-in handlebar
(A)
Securing the electric wire (SC-E8000/SC-E7000)
(A)
(B)
(C)
Bind the brake horse (or brake outer casing) to the electric wire connecting the cycle computer and drive unit, using the band, as shown in the illustration.
(A)
Electric wire of the cycle computer
(B)
Brake horse
(or brake outer casing)
(C)
Band
TECH TIPS
Bands are included with the SC-E8000/
SC-E7000.
2-14
Chapter2 INSTALLATION
Connecting the electric wire
Example of routing the electric wire (SC-E6010/SC-E6100)
(A) (B) (C)
Example 1:
Secure the electric wire of the switch unit
(A)
to the handlebar using the cable band
(B)
. Wind the excess electric wire around the area between the cycle computer
(C)
and stem
(D)
, then connect the wire to the cycle computer.
(A)
Switch unit
(B)
Cable band
(C)
Cycle computer
(D)
Stem
(D)
(F)
(E)
(G)
Example 2:
Secure the electric wire of the switch unit to the handlebar using the cable band. Bind the electric wire of the assist switch and that of the cycle computer
(E)
to the brake outer casing
(F)
using the band
(G)
and connect the electric wire of the assist switch to the cycle computer.
(E)
Electric wire of the cycle computer
(F)
Brake outer casing
(G)
Band
TECH TIPS
Bands are included with the SC-E6010/
SC-E6100.
Routing the electric wire (EW-EN100)
(A)
(B)
Secure the switch unit's electric wire.
• Determine the locations of the cable bands, and then secure the electric wire in place along the handlebar so that there is no slack.
(A)
Switch unit
(B)
Cable band
(C)
Drive unit
1
(C)
EW-EN100
To be continued on next page
2-15
Chapter2 INSTALLATION
Connecting the electric wire
2
(A)
(B)
Connect the electric wire to the E-TUBE port on EW-EN100.
• If necessary, use bands to secure the electric wire connecting the switch unit and EW-EN100 to either the brake hose or brake outer casing.
(A)
Brake outer casing
(B)
Band
2-16
Chapter2 INSTALLATION
Installing the battery mount
Installing the battery mount
BM-E8010
(A)
(B)
(C)
(y)
(C)
(B)
(y)
Front of bicycle
(z)
Rear of bicycle
(A)
Key unit
(B)
Battery connection unit
(C)
Mount upper case
(D)
Mount lower case
(E)
Frame
(D)
(E)
(z)
Set in place the rubber spacers and metal spacer on the mount lower case and align the frame mounting holes with the bolt holes in the mount lower case.
(A)
Mount lower case
(B)
Metal spacer
(C)
Rubber spacer
(D)
Frame
(E)
Frame mounting hole
(A)
1
(D)
(E)
To be continued on next page
2-17
Chapter2 INSTALLATION
Installing the battery mount
2
(B) (A)
Secure the mount lower case by tightening the two types of mount fixing bolt (M5).
Tighten the mount fixing bolt (M5) (low head type) first.
(C)
(A)
Mount fixing bolt (M5)
(hexagon bolt type):
Use a 3 mm hexagon wrench or
8 mm spanner on the mount fixing bolt.
(B)
Mount fixing bolt (M5)
(low head type):
Use a 3 mm hexagon wrench on the mount fixing bolt.
(C)
Mount lower case
Tightening torque
3 N·m
(B)
(C)
Temporarily attach the key unit with the key unit fixing bolts (M5).
(A)
Key unit:
Key unit is not included with
SHIMANO products.
(B)
Key unit fixing bolt (M5)
(C)
Washer
3
(A)
(C)
4
(A) (B)
Adjust the position of the key unit so that the distance between section
(A)
of the key unit and section
(B)
of the mount lower case is
224.4 mm
and then fully tighten the key unit fixing bolts.
Tightening torque
3 N·m
224.4 mm
To be continued on next page
2-18
Chapter2 INSTALLATION
Installing the battery mount
(A)
Temporarily attach the key unit cover to the key unit and adjust so that the battery can be smoothly connected/ disconnected and no noise is produced due to looseness during riding.
(A)
Key unit cover
(B)
Battery
5
(B)
6
(B)
(A)
(B)
Secure the key unit cover with the key unit cover fixing bolts (M4).
(A)
Key unit cover
(B)
Key unit cover fixing bolt (M4)
Tightening torque
0.6 N·m
To be continued on next page
2-19
Chapter2 INSTALLATION
Installing the battery mount
(C)
(D)
(A)
(B)
Route the power cord through the cable routing hole.
Align the protruding parts of the mount upper case and mount lower case.
Pull the power cord until the rubber bush is implanted in the cable routing hole.
(A)
Power cord
(B)
Cable routing hole
(C)
Mount upper case
(D)
Mount lower case
(E)
Rubber bush
7
(E)
8
(C)
(C)
(A)
(B)
Tighten on the mount upper case using the mount upper case fixing bolts (M3).
(A)
Mount upper case
(B)
Mount lower case
(C)
Mount upper case fixing bolt (M3)
Tightening torque
0.6 N·m
2-20
Chapter2 INSTALLATION
Installing the battery mount
BM-E8020
Assembly of the battery connection unit
(y)
(A)
(B)
(z)
(y)
Front of bicycle
(z)
Rear of bicycle
(A)
Frame
(B)
Battery connection unit
(C)
Mount upper case and mount lower case when assembled
(C)
Align the frame mounting holes with the bolt holes in the mount lower case.
(A)
Mount lower case
(B)
Frame
(C)
Frame mounting hole
1
(A)
(B) (C)
To be continued on next page
2-21
Chapter2 INSTALLATION
Installing the battery mount
(A)
Secure the mount lower case to the frame by the tightening the mount fixing bolts (M8).
(A)
Mount fixing bolt (M8)
(B)
Mount lower case
(C)
Frame
Tightening torque
10 N·m
2
(B)
3
(A)
(C)
(B) (C)
Route the power cord through the cable routing hole in the mount lower case and then tighten on the mount upper case using the mount upper case fixing bolts (M3).
(A)
Mount upper case
(B)
Mount lower case
(C)
Cable routing hole
(D)
Mount upper case fixing bolt (M3)
Tightening torque
0.6 N·m
(D)
To be continued on next page
2-22
Chapter2 INSTALLATION
Installing the battery mount
Assembly of the key unit
(B)
(y)
(A)
(z)
(y)
Front of bicycle
(z)
Rear of bicycle
(A)
Frame
(B)
Key unit
(A)
Insert the key cylinder into the key unit.
Secure the key cylinder in place by tightening the key cylinder fixing bolts
(M4) from the reverse side of the key unit.
(z)
Reverse side of key unit
(B)
(A)
Key cylinder:
Key cylinder is not included with
SHIMANO products.
(B)
Key unit
(C)
Key cylinder fixing bolt (M4)
Tightening torque
0.6 N·m
4
(C)
(z)
To be continued on next page
2-23
Chapter2 INSTALLATION
Installing the battery mount
5
(A)
(C) (B) (B) (C)
Align the fixing bolt holes in the key unit with the frame mounting holes.
Temporarily attach the key unit to the frame with the key unit fixing bolts (M8).
Attach the bolt detachment prevention rubbers.
(A)
Key unit
(B)
Key unit fixing bolt (M8)
(C)
Bolt detachment prevention rubber
(D)
Frame
(E)
Frame mounting hole
(D)
(E)
(A) (B)
Adjust the position of the key unit so that the distance between section
(A)
of the key unit and section
(B)
of the battery connection unit is
347.2 mm
and then fully tighten the key unit fixing bolts.
Tightening torque
10 N·m
6
347.2 mm
(A)
7
(B)
Temporarily attach the key unit cover to the key unit and adjust so that the battery can be smoothly connected/ disconnected and no noise is produced due to looseness during riding.
(A)
Key unit cover
(B)
Battery
To be continued on next page
2-24
Chapter2 INSTALLATION
Installing the battery mount
(C)
8
(B) (A)
Attach the key unit cover to the key unit.
Secure in place the key unit with the key unit fixing bolts (M3).
(A)
Key unit cover
(B)
Key unit
(C)
Key unit cover fixing bolt (M3)
Tightening torque
0.6 N·m
2-25
Chapter2 INSTALLATION
Installing / removing the battery
Installing / removing the battery
Installation of the battery
BT-E8010
Align the indentation in the bottom of the battery with the protrusion on the mount and insert the battery.
1
Slide the battery to the right starting from the point where it is inserted.
Push in the battery until you hear it click.
2
3
Return the key to the locking position, remove it, and store it in a safe place.
NOTICE
•
To prevent the battery from falling out, check to see that the battery is locked after installation.
•
Before riding, make sure that the charging port cap is closed.
•
To prevent the battery from falling out, do not ride the bicycle with the key inserted.
2-26
Chapter2 INSTALLATION
Installing / removing the battery
BT-E8020
(A)
(B)
Insert the battery into the battery mount until there is a click.
• When inserted until a click is heard, the battery is locked automatically.
(A)
Battery
(B)
Battery mount
NOTICE
•
To prevent the battery from falling out, check to see that the battery is locked after installation.
•
Before riding, make sure that the keyhole cap and charging port cap are closed.
•
To prevent the battery from falling out, do not ride the bicycle with the key inserted.
Keyhole cap
Charging port cap
2-27
Chapter2 INSTALLATION
Installing / removing the battery
Removing the battery
The following description may not be applicable as different types of keys are available.
BT-E8010
(A)
Turn off the power, then insert the key into the key cylinder in the battery holder.
1
(B)
(A)
Key
(B)
Key cylinder
NOTICE
Hold the battery firmly and be careful that it does not drop when removing or carrying it.
TECH TIPS
•
The position of the key does not affect the insertion of the battery. You can insert it regardless of the key position.
•
You cannot remove the key when it is not in the inserting position.
To unlock the battery turn the key to the left until you feel some resistance.
2
Hold the upper part of the battery and slide it to the left to remove it.
3
2-28
Chapter2 INSTALLATION
Installing / removing the battery
BT-E8020
If using a battery cover manufactured by another company, remove the battery cover before removing the battery.
Remove the keyhole cap.
(A)
Key hole cap
1
(A)
2
(B)
(A)
Insert the key into the key cylinder in the battery mount.
(A)
Key cylinder
(B)
Key
TECH TIPS
•
The position of the key does not affect the insertion of the battery. You can insert it regardless of the key position.
•
You cannot remove the key when it is not in the inserting position.
To unlock the battery, turn the key clockwise and push it in.
3
4
Remove the key from the key cylinder, close the keyhole cap, and detach the battery.
NOTICE
•
Support the battery with your hand when detaching to make sure that it does not fall out.
•
Do not attach or detach the battery with the key left inserted into the key cylinder or the keyhole cap left open. The battery may be damaged from contact with the handle of the key or the keyhole cap.
2-29
Chapter2 INSTALLATION
Installing the speed sensor
Installing the speed sensor
SM-DUE10
(A)
1
2
(B)
(C)
(a)
(A) (B)
(D)
Before installing the speed sensor, check that the clearance
(a)
between the speed sensor and the magnet unit will be within 3 to 17 mm.
(A)
Speed sensor
(B)
Magnet unit
(C)
Spoke
(D)
Chain stay
If the clearance is within the designated range, place the toothed washer between the speed sensor and the chain stay, then attach the speed sensor mounting bolt.
TECH TIPS
When checking the clearance is within 17 mm, take wheel truing, frame distortion, etc. into account.
(A)
Toothed washer
(B)
Speed sensor mounting bolt
(16 mm)
Tightening torque
1.5 - 2 N·m
3
If the clearance exceeds 17 mm, use a spacer to adjust it.
Attach the speed sensor with the speed sensor mounting bolt.
(A)
Spacer
(B)
Speed sensor mounting bolt
(22 mm)
Tightening torque
1.5 - 2 N·m
(A) (B)
SM-DUE11
(A)
Install the speed sensor with the 2 speed sensor mounting bolts.
(A)
Speed sensor mounting bolt
Tightening torque
0.6 N·m
2-30
Chapter2 INSTALLATION
Mounting the magnet
Mounting the magnet
SM-DUE10
Magnet mounting position
Mount the magnet so that its center is aligned over the apex of the triangle symbol.
How to mount the magnet
(A)
1
(B)
(C)
Align the speed sensor and magnet unit as shown in the illustration.
(A)
Speed sensor
(B)
Magnet unit
(C)
Spoke
Tighten the mounting bolt with a screwdriver.
(A)
Mounting bolt
Tightening torque
1.5 - 2 N·m 2
(A)
2-31
Chapter2 INSTALLATION
Mounting the magnet
SM-DUE11
(A)
(B)
Use the special magnet model for the disc brake rotor.
(A)
Magnet unit
(B)
Speed sensor
NOTICE
Refer to General Operations for installation of the disc brake rotor.
2-32
Chapter3 INSTALLING AND
WIRING THE DRIVE UNIT
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the drive unit
INSTALLING AND WIRING THE DRIVE UNIT
Installing the drive unit
Route the cables before installing the drive unit.
(A)
Align the drive unit with the three mounting holes on the right side and left side of the frame.
(A)
Mounting hole
(B)
Drive unit
NOTICE
Be careful not to pinch the cables with the frame or drive unit case.
1
2
Right side
(B)
Left side
(y)
First attach the drive unit fixing bolts
(M8) to the right side.
After this, attach the drive unit fixing bolts (M8) to the left side.
Tighten the drive unit fixing bolts (M8) until the drive unit makes firm contact with the inside of the right side of the frame.
(y)
Front of bicycle
(z)
Rear of bicycle
TECH TIPS
Drive unit fixing bolts (M8) are not included with SHIMANO products. Use those supplied by the manufacturer. Tighten the bolts to the following tightening torque when attaching the drive unit to the frame.
Tightening torque
10 - 12.5 N·m
(z)
3-2
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Drive unit wiring diagram
Drive unit wiring diagram
(C)
(A)
(A)
(B)
(A)
Cycle computer port/
Rear derailleur port/E-TUBE port
(B)
Dummy plug
(C)
Speed sensor port
NOTICE
Be sure to attach dummy plugs to any unused ports.
TECH TIPS
The cycle computer/rear derailleur ports can be used to connect the cycle computer or rear derailleur.
3-3
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Connecting the power cord
Connecting the power cord
Connecting to the drive unit
Align the arrow on the power cord with the triangle symbol on the drive unit port and insert the power cord.
Insert it until it locks into place.
(A)
Power cord
(B)
Drive unit port
(A)
(B)
Disconnecting from the drive unit
To remove the power cord, hold it by the grooved part of its end and pull it towards yourself.
3-4
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Connecting switches and the drive unit to the cycle computer (SC-E8000/SC-E7000)
Connecting switches and the drive unit to the cycle computer (SC-E8000/SC-E7000)
Use the TL-EW02 for connection.
(B)
(A) (C)
(A)
Cycle computer
(B)
Assist switch
(C)
Shift switch
(D)
Drive unit
(E)
TL-EW02
NOTICE
Be sure to attach dummy plugs to any unused ports.
(E)
(D)
TECH TIPS
The electric wire connector can be connected to any port of the cycle computer, but we recommend you connect the assist switch to the switch-side port.
Connecting the assist switch and drive unit to the cycle computer (SC-E6010/SC-E6100)
Use the TL-EW02 (D) for connection.
(B)
(A)
(B)
(A)
Cycle computer
(B)
Assist/Shift switch
(C)
Drive Unit
(D)
TL-EW02
TECH TIPS
The electric wire connector can be connected to any port of the cycle computer, but we recommend you connect the assist switch to the switch-side port.
(D)
(C)
3-5
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Connecting the switch unit and drive unit to junction [A] (EW-EN100)
Connecting the switch unit and drive unit to junction [A] (EW-EN100)
(A)
Switch unit
(B)
Drive Unit
EW-EN100
(A)
(B)
3-6
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Connecting the speed sensor to the drive unit
Connecting the speed sensor to the drive unit
Connect the speed sensor unit electric wire to the drive unit speed sensor port using the TL-EW02.
(A)
TL-EW02
(B)
Speed sensor port
(A)
(B)
3-7
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Connecting the light cable to the drive unit
Connecting the light cable to the drive unit
Remove the crank and drive unit cover and loosen the mounting bolts of the light connection terminals.
1
(A)
(A)
Light connection terminal
(B)
Mounting bolt
TECH TIPS
For information on compatible lights, contact a manufacturer of completed bicycles.
(B)
2
(A) (B)
Attach the front light cable and tail light cable to the terminals and secure them with the mounting bolts.
(A)
Front light cable
(B)
Taillight cable
Tightening torque
0.6 N·m
Attach the drive unit cover.
Tighten the cover fixing bolts (M3) in the three locations.
(A)
Cover fixing bolt (M3)
Tightening torque
0.6 N·m
3
(A)
3-8
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the crank and chainring unit
Installing the crank and chainring unit
Perform the procedure below for all models, regardless of whether gear shifting is electrical or mechanical.
Align the wide part of the left crank arm with the wide part of the chainring through axle and then attach.
(A)
Wide groove area (left crank arm)
(B)
Wide part
(chainring through axle)
(C)
Left crank arm
(D)
Axle spacer
(A)
(B)
NOTICE
Left or right is indicated on each crank arm.
Check the L and R markings when installing.
1
L R
(C) (D)
Left crank arm Right crank arm
(A)
TL-FC16/TL-FC18
(B)
Cap
Tightening torque
0.7 - 1.5 N·m
2
Use the SHIMANO original tool to tighten the cap.
(A) (B)
To be continued on next page
3-9
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the crank and chainring unit
(z)
(C)
(A)
3
(B)
Push in the stopper plate and check that the plate pin is securely in place, and then tighten the bolt of the left crank arm.
Tighten both bolts equally to the specified tightening torque (12 - 14 N·m).
(z)
The illustration is of the left crank arm (cross-section)
(A)
Plate pin
(B)
Stopper plate
(C)
Left crank arm
Tightening torque
12 - 14 N·m
NOTICE
•
The two bolts should be tightened at the same time rather than each bolt being fully tightened separately.
•
Set the stopper plate in the correct direction as shown in illustration.
4
5
(A) (B)
(A)
Attach the drive unit cover.
Tighten the cover fixing bolts (M3) in the three locations.
(A)
Cover fixing bolt (M3)
Tightening torque
0.6 N·m
If using a chain device, temporarily tighten the back plate to the mounting member of the chainring unit.
(A)
Back plate fixing bolt (M6)
(B)
Back plate
To be continued on next page
3-10
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the crank and chainring unit
(A) (B)
When attaching the chainring unit, align the cutout in the chainring unit with the wide area of the chainring mounting member.
(A)
Chainring unit
(B)
Chainring mounting member
NOTICE
•
For details on the compatibility of the chain device and chainring unit, refer to compatibility information (https:// productinfo.shimano.com/).
•
Note the difference between the front and back of the chainring unit. The front has a gear size (tooth number) marking.
Front
6
Back
7
(A)
Mount the chain on the chainring unit.
(A)
Chain
NOTICE
When mounting the chain, make sure to match chainring unit tooth thickness (thick/ thin) and chain inner width (wide/narrow).
To be continued on next page
3-11
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the crank and chainring unit
/
(x)
(y)
(A)
8
(z)
(B)
Determine the position of the guide according to the number of teeth on the crank.
Install the guide by temporarily tightening the guide fixing bolt (M5)
(x)
38T
(y)
34T
(z)
36T
(A)
Guide
(B)
Guide fixing bolt (M5)
9
(B)
(z)
(A)
(D)
(C)
If using a chain device, after attaching the chain, rotate the back plate so that the clearance between the chain and the rubber band is 0 - 1 mm.
Adjustment should be performed under the following conditions.
• Chain is engaging the smallest sprocket
• Rear suspension is fully extended
After adjustment, fully tighten the back plate and guide.
(z)
0 - 1 mm
(A)
Rubber band
(B)
Chain
(C)
Guide fixing bolt (M5)
(3 mm hexagon wrench / 4 mm hexagon wrench)
(D)
Back plate fixing bolt (M6)
(3 mm hexagon wrench)
Tightening torque
4 N·m
(Guide fixing bolt)
5 - 7 N·m
(Back plate fixing bolt)
4 N·m
(Guide fixing bolt)
NOTICE
If the chain and chain device interfere with each other when SM-CDE80 is used on a bicycle with Rear suspension at sag position , please adjust angle the chain device not to touch chain in the position of Low gear.
To be continued on next page
3-12
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the crank and chainring unit
(B)
Tighten the lock ring by hand and attach the SHIMANO original tool.
While holding the left crank, tighten the lock ring in the direction shown in the illustration.
(A)
TL-FC39/TL-FC36
(B)
Lock ring
Tightening torque
35 - 45 N·m
NOTICE
•
If using a torque wrench, use TL-FC39 in combination with TL-FC33.
(A)
10
TL-FC39 TL-FC33
•
An impact wrench cannot be used.
TECH TIPS
•
The lock ring has a left hand thread.
•
Combine the SHIMANO original tools as in the illustration. Set TL-FC39 to TL-FC36 using the 2 installation holes on TL-FC39.
TL-FC39
Installation hole
TL-FC36
To be continued on next page
3-13
Chapter3 INSTALLING AND WIRING THE DRIVE UNIT
Installing the crank and chainring unit
Install the right crank arm.
Use the SHIMANO original tool to tighten the cap.
(A)
Cap
(B)
Right crank arm
(C)
Axle spacer
Tightening torque
0.7 - 1.5 N·m
11
(A)
(C)
(B)
(z)
(C)
(A)
12
(B)
Push in the stopper plate and check that the plate pin is securely in place, and then tighten the bolt of the right crank arm.
Tighten both bolts equally to the specified tightening torque (12 - 14 N·m).
(z)
The illustration is of the right crank arm (cross-section)
(A)
Plate pin
(B)
Stopper plate
(C)
Right crank arm
Tightening torque
12 - 14 N·m
NOTICE
•
The two bolts should be tightened at the same time rather than each bolt being fully tightened separately.
•
Set the stopper plate in the correct direction as shown in illustration.
3-14
Chapter4 CHARGING THE BATTERY
Chapter4 CHARGING THE BATTERY
Proper use of the battery
CHARGING THE BATTERY
The battery cannot be used immediately after purchase as it will be in deep sleep mode. Charging the battery with the dedicated battery charger will release the battery from deep sleep mode, allowing the battery to be used.
The battery can be used when the LED on it turns on.
The battery can also be released from deep sleep mode by connecting to E-TUBE PROJECT when the bicycle is fitted with all components.
Please read the SHIMANO STEPS special battery and parts user's manual for the latest information about charging and handling the battery.
Proper use of the battery
Charging can be carried out at any time regardless of the amount of charge remaining, but you should fully charge the battery in the following cases. Be sure to use the dedicated charger to charge the battery.
• The battery is not ready for use at the time of shipment. Before riding, be sure to charge the battery until it is fully charged.
If the battery has become completely discharged, charge it as soon as possible. If you leave the battery uncharged, the battery may deteriorate.
• If the bicycle will not be ridden for a long time, store with the battery level at around 70%.
Charge the battery every six months to prevent it from fully discharging.
• Do not connect to E-TUBE PROJECT while the battery is being charged.
The use of a genuine SHIMANO battery is recommended. If using a battery from another manufacturer, make sure to carefully read the owner's manual for the battery before use.
• Connect to E-TUBE PROJECT and click [Connection check] to confirm whether the battery in use is a genuine SHIMANO battery or another brand.
4-2
Chapter4 CHARGING THE BATTERY
Charging the battery
Charging the battery
When charging the battery alone
Battery charger: EC-E6000
Battery: BT-E8010/BT-E8020
1
Connect the battery charger’s power plug to the outlet.
BT-E8010
Insert the charging plug into the battery's charging port.
(A)
(A)
Charging port
(B)
Battery
NOTICE
Charge the battery on a flat surface indoors.
(B)
2
BT-E8020
(A)
(B)
4-3
Chapter4 CHARGING THE BATTERY
Charging the battery
When charging the battery while it is mounted on the bicycle
Battery charger: EC-E6000
Battery: BT-E8010/BT-E8020
1
Connect the charger’s power plug to the outlet.
BT-E8010
Insert the charging plug into the battery mount charging port.
(A)
Battery mount
(B)
Charging port
(C)
Charging plug
TECH TIPS
•
Place the battery charger on a steady surface such as the floor before charging.
•
Stabilize the bicycle to ensure that it does not collapse during charging.
(B)
(A)
(C)
2
BT-E8020
(B)
(A)
(C)
4-4
Chapter4 CHARGING THE BATTERY
About the charger LED lamp
About the charger LED lamp
(A)
After charging has started, the LED lamp on the charger lights up.
You can check the current charging status on the battery level lamp located on the battery.
Lit up
Charging
(Within 1 hour after the completion of charging)
Charging error
Blinking
Turned off
Battery disconnected
(1 hour or more after the completion of charging)
(A)
Charger LED lamp
DANGER
Use the battery and charger combination specified by the company for charging and follow the charging conditions specified by the company. Not doing so may cause overheating, bursting, or ignition of the battery.
NOTICE
If the bicycle is stored for an extended period of time immediately after purchase, you will need to charge the battery before using the bicycle. Once the battery is charged, it starts to deteriorate slightly.
About the battery LED lamps
(A)
Battery LED lamp
(A)
Charging-in-progress indication
Battery level indication *1 Battery level
0 - 20%
21 - 40%
41 - 60%
61 - 80%
81 - 99%
100%
* 1 : No light : Lit up : Blinking
4-5
Chapter4 CHARGING THE BATTERY
About the battery LED lamps
Battery level indication
The current battery level can be checked by pressing the battery's power button.
Battery level indication *1 Battery level
100 - 81%
80 - 61%
60 - 41%
40 - 21%
20 - 1%
0%
(When battery is not installed on bicycle)
0%, Power off / Shutdown
(When battery is installed on bicycle)
* 1 : No light : Lit up : Blinking
NOTICE
When remaining battery capacity is low, system functions begin to shut off in the following order.
1. Power assistance (Assist mode automatically switches to [ECO] and then assistance shuts off. The switch to
[ECO] occurs earlier if a battery-powered light is connected.)
2. Gear shifting
3. Light
4-6
Chapter4 CHARGING THE BATTERY
About the battery LED lamps
Error indication
System errors and similar warnings are indicated by the battery LED lamps through various lighting patterns.
Error indication type
System error
Temperature protection
Security authentication error
Indication condition
Communication error with the bicycle system
If the temperature exceeds the guaranteed operating range, the battery output is turned off.
This is displayed if a genuine drive unit is not connected.
This is displayed if any of the cables are disconnected.
Lighting pattern *1 Recovery
Make sure that the cable is not loose or improperly connected.
If the situation does not improve, contact an agency.
Leave the battery in a cool place away from direct sunlight until the internal temperature of the battery decreases sufficiently.
If the situation does not improve, contact an agency.
Connect a genuine battery and drive unit.
Check the condition of the cables.
If the situation does not improve, contact an agency.
Charging error
Battery malfunction
This is displayed if an error occurs during charging.
Electrical failure inside the battery
Remove the connector between the battery and charger, and press the power switch with only the battery connected.
If an error appears with only the battery connected, contact an agency.
Use the battery power button to turn the power OFF, and then turn the power back ON.
* 1 : No light : Lit up : Blinking
4-7
Chapter4 CHARGING THE BATTERY
Turning the power ON / OFF
Turning the power ON / OFF
Turning the power ON and OFF via the cycle computer (SC-E6010/SC-E6100)
< SC-E6010 > < SC-E6100 >
< SC-E6010 >
Hold down the power button
(A)
on the cycle computer for 2 seconds.
< SC-E6100 >
Press the power button
(A)
on the cycle computer.
(A)
(A)
(A)
Power button
NOTICE
(SC-E6100)
If the battery level of the cycle computer falls to zero, the cycle computer will not start, and operations using power will not be possible.
If nothing is displayed on the screen even when the power switch is pressed, perform one of the following operations to charge the battery.
•
Press the power button on the body of the
(main) battery to turn the power ON.
•
If there is a charging port or if there is a battery mount with a connected charging port installed, charge the (main) battery from the charging port.
•
Use SM-PCE1 or SM-PCE02 to connect to a
PC, then charge the built-in battery from the E-TUBE PROJECT.
The low battery level icon blinks while charging, and disappears once complete.
Turning the power ON and OFF via the battery
BT-E8010
(A)
Press the power button on the battery.
The LED lamps will light up indicating remaining battery capacity.
BT-E8020
(A)
Power button
NOTICE
•
When turning on the power, check that the battery is firmly attached to the holder.
•
Power cannot be turned on while charging.
•
Do not place your foot on the pedals when turning on.
A system error may result.
(A)
TECH TIPS
•
To force power off, hold down the power button for 6 seconds.
•
If the bicycle has not moved for over 10 minutes, the power will automatically turn off. (Automatic power off function)
4-8
Chapter4 CHARGING THE BATTERY
Turning the power ON / OFF
Screen display when power is turned ON
SC-E8000/SC-E7000
When the main power is turned ON, a screen similar to that shown below is displayed, and then switches to the basic screen.
< EW-EN100 >
When the main power is turned ON, the
LED2 lights up.
SC-E6010/SC-E6100
Normal startup
(A)
LED2
Battery level low (SC-E6100)
* The cycle computer's battery level is low.
EW-EN100
(A)
4-9
Chapter5 HOW TO OPERATE
Chapter5 HOW TO OPERATE
Cycle computer and switch units
HOW TO OPERATE
Cycle computer and switch units
The operation procedure provided here refers to cases where the cycle computer is set to the default values.
SC-E8000/SW-E8000-L/SW-M8050-R (SW-M9050-R)
Left switch
SW-E8000-L
Right switch
SW-M8050-R
(SW-M9050-R)
Function button
Y X X Y
SC-E6010/SW-E6010
X
A
Y
Light button
Power button
X
A
Y
SC-E6100/SW-E6010
X
A
Y
Function button
Light button
Power button
X
A
Y
SC-E7000/SW-E7000
X
Y
X
Y
Function button
5-2
Chapter5 HOW TO OPERATE
Junction [A]
Assist-X
Assist-Y
Assist-A
Left switch
(default: for assistance)
When riding:
Increase assistance
When setting:
Move cursor or change setting
When riding:
Decrease assistance
When setting:
Move cursor or change setting
When riding:
Switch traveling data displayed on cycle computer
When setting:
Switch cycle computer screen or confirm setting changes
Shift-X
Shift-Y
Shift-A
Function button
(SC-E6100)
Cycle computer (SC-E6010/SC-E6100)
When riding:
Switch traveling data displayed on cycle computer
When setting:
Switch cycle computer screen or confirm setting changes
Light button
Power button
Right switch
(default: for electronic shifting)
When riding:
Shift up
When riding:
Shift down
Not used.
Light ON/OFF
Main power ON/OFF
Function button
Cycle computer (SC-E8000/SC-E7000)
When riding:
Switch traveling data displayed on cycle computer
When setting:
Switch cycle computer screen or confirm setting changes
Junction [A]
EW-EN100 has the function to change the assist mode and can be used in place of a cycle computer.
Button
Button
Junction [A] (EW-EN100)
Press:
Changes assist mode (each time button is pressed)
Hold (around two seconds):
Turns the light ON/OFF
NOTICE
It is not recommended to operate the button on EW-EN100 while riding. Select your preferred assist mode prior to riding.
TECH TIPS
•
A switch unit connection is required to change to walk assist mode.
•
The function of switching to and from setting mode can be assigned to the button. Refer to "Setting Mode (EW-EN100)" in "HOW TO OPERATE."
5-3
Chapter5 HOW TO OPERATE
Basic screen display of the cycle computer
Basic screen display of the cycle computer
SC-E8000
(A) (B)
SC-E6010
SC-E6100
SC-E7000
(E) (D) (C)
(G)
(F)
(E)
(D)
(C)
(H)
(A)
(B)
(F)
(E)
(D)
(C)
(H)
(G) (J)
(A)
(I)
(B)
(A) (J) (I) (B)
(D) (E)/(H)
5-4
(A) Battery level indicator
Displays the current battery level.
(B) Gear position (Only displays when electronic gear shifting is in use)
Displays the currently set gear position.
Current gear position (SC-E6010/
SC-E6100)
Shifting advice*1 (SC-E6100)
This notifies you of the recommended timing at which to shift based on the bicycle riding conditions.
(C) Assist gauge
Displays assistance level.
(D) Current assist mode
(E) Current speed
*2
Displays the current speed.
The display can be switched between km/h and mph.
(F) Current time
Shows the current time.
(G) Light icon
Indicates that the light connected to the drive unit is lit.
(H) Traveling data display
Displays the current traveling data.
(I) Maintenance alert
Indicates that maintenance is required. Contact your place of purchase or a bicycle dealer if this icon is displayed.
(J) Bluetooth
®
LE icon
Displayed when connected over
Bluetooth LE.
*1 Only for electronic gear shifting.
*2 [Manual]/[M] will always be displayed for rear derailleur models.
Chapter5 HOW TO OPERATE
Displaying the basic status of junction [A]
Displaying the basic status of junction [A]
EW-EN100
(A)
The LEDs indicate the following statuses.
• Current battery level
• Current assist mode
Refer to "Battery level indicator" (next section) in "HOW TO OPERATE" and
"Switching the Assist Mode" in "HOW
TO OPERATE."
(A)
LED
5-5
Chapter5 HOW TO OPERATE
Battery level indicator
Battery level indicator
SC-E8000/SC-E6100/SC-E7000
Display Battery level
100 - 81%
80 - 61%
60 - 41%
40 - 21%
20 - 1%
0%
SC-E6010
Display Battery level
100%
The battery level is shown as an icon.
< EW-EN100 >
LED2 shows the battery level when the power is ON.
(A)
LED2
TECH TIPS
•
For SC-E8000/SC-E7000, the battery level indicator will flash when the battery level is low.
•
The cycle computer and battery use zero to indicate a battery level where the entire system (including the lights which remain on after the assist function stops) ceases to function. Therefore, assist may stop before
0% is indicated, depending on the settings.
0%
EW-EN100
LED2 display
(lit up)
(lit up)
(flashing)
Battery level
100 - 21%
20% or less
Nearly empty
(A)
5-6
Chapter5 HOW TO OPERATE
Switching the assist mode
Switching the assist mode
Switching the assist mode with the switch unit
Y X
Assist
X
Y
[BOOST]
[TRAIL]
[ECO]
[OFF]
Press Assist-X or Assist-Y to switch assist modes.
If no assist switch is connected when using SC-E6100 or SC-E7000, you can also hold down the function button to switch to assist mode.
Function button
[BOOST]
: Assist boost
[TRAIL]
: Assist trail
[ECO]
: Assist eco
[OFF]
: Assist off
[WALK]
: Walk assist
[WALK]
: Short press Assist-X
: Short press Assist-Y
: Long press Assist-Y
: Short press Assist-X (This operation is for canceling [WALK] mode)
TECH TIPS
If a switch unit is connected to EW-EN100, the
LED will indicate the assist mode (as shown in the next section).
Switching the assist mode with EW-EN100
Explain to the customer that it is not recommended to operate the device while riding.
Button
LED1 indication
(off)
(lit up)
(lit up)
Assist mode
[OFF]
[ECO]
[TRAIL]
Press the button.
• The assist mode switches each time the button is pressed. LED1 display switches each time the assist mode is switched.
(lit up)
(off)
[BOOST]
[OFF]
(A)
Button
(B)
LED1
(A)
(B)
5-7
Chapter5 HOW TO OPERATE
Walk assist mode
Walk assist mode
• The use of the walk assist mode function is prohibited by law in some regions.
• The walk assist function operates at a maximum of 6 km/h. During electronic gear shifting, the assist level and speed are controlled by the gear position.
• Switching to walk assist mode requires a switch unit that has been assigned the change assist mode function.
• The intelligent walk assist function activates when an electronic gear shifting system (such as XTR or DEORE XT SEIS) is connected.
The system provides assistance according to the detected gear position.
"Intelligent walk assist" generates higher torque when ascending a sudden slope at low speed.
The "quick walk assist" function can be started immediately by pressing the switch when in any mode.
5-8
Chapter5 HOW TO OPERATE
Walk assist mode
Switching to walk assist mode
Assist
Y
SC-E8000
Y
With your feet off the pedals and current speed at [0 km/h], hold down
Assist-Y until [WALK] displays.
< EW-EN100 >
Without stepping on the pedals and with the current speed at [0 km/h], hold down
Assist-Y until the LED1 lights up blue.
(A)
LED1
NOTICE
•
The Walk assist mode function may not be able to be used in certain regions.
•
A warning tone will sound if it is not possible to switch to [WALK] mode because the current speed is not [0 km/h] or there is pressure on the pedals.
TECH TIPS
•
If Assist-Y is not pressed for one minute or more, the mode active before [WALK] mode was set is re-activated.
•
If the bicycle is not moved after [WALK] mode is activated, walk assist is automatically inactivated. To re-activate
[WALK] mode, momentarily release Assist-Y and then hold down Assist-Y.
•
The walk assist function can operate at a maximum of 6 km/h.
•
The assistance level and speed vary with the gear position.
SC-E6010
SC-E6100
EW-EN100
Assist OFF
Walk assist mode enabled
(A)
5-9
Chapter5 HOW TO OPERATE
Walk assist mode
Walk assist mode operation
Prior to operation, firmly grip the handlebar and note your surroundings. When walk assist begins, the bicycle will be driven by the drive unit.
Assist
(A)
LED1
< SC-E6100 >
Y
Y
Continue to press Assist-Y while in walk assist mode.
• Walk assist will function only while
Assist-Y is pressed.
• If a switch unit is connected to
EW-EN100, LED1 will flash blue when walk assist starts.
1
< EW-EN100 >
Walk assist mode enabled
Walk assist started
(A)
2
Carefully push the bicycle together with walk assist.
< SC-E6100 >
Removing your finger from Assist-Y will stop walk assist.
(A)
LED1
3
< EW-EN100 >
Walk assist running
Walk assist mode enabled
(A)
To be continued on next page
5-10
Chapter5 HOW TO OPERATE
Walk assist mode
Assist
X
4
X
< EW-EN100 >
Walk assist mode enabled
Assist OFF
Press Assist-X to exit walk assist mode.
• [WALK] mode is canceled, and the system restarts in the mode it was in prior to setting [WALK] mode.
(A)
LED1
(A)
5-11
Chapter5 HOW TO OPERATE
Switching the travel data display (SC-E8000/SC-E6010)
Switching the travel data display (SC-E8000/SC-E6010)
(A)
Traveling data display
(A)
(A)
(B)
(C)
(D)
[DST]
[ODO]
[RANGE]
[TIME]
A
Assist
Function button
[CLOCK] (H)
[CADENCE] (G)
[MAX] (F)
[AVG] (E)
* The Walk assist mode function may not be able to be used in certain regions.
The type of travel data displayed changes each time you press Assist-A or the cycle computer's function button.
(A)
Traveling distance
(B)
Cumulative distance
(C)
Traveling range *1, 2
(D)
Traveling time *3
(E)
Average speed *3
(F)
Maximum speed *3
(G)
Crank rotation speed *3
(H)
Current time *4
*1
The battery level is not displayed while displaying the traveling range.When
[RANGE] is displayed, the battery level is not displayed. The traveling range should be used as a reference only.
*2
When walk assistance is functioning, the on screen display [RANGE] changes to
[RANGE ---].
*3
Optional item: You can configure the display settings in E-TUBE PROJECT. For details, refer to the "CONNECTION AND
COMMUNICATION WITH DEVICES" section.
*4
Displayed constantly on SC-E6010.
NOTICE
•
When traveling data is displayed, the screen returns to speed display after 60 seconds.
•
When speed data is displayed, pressing
Assist-A or the function button changes the traveling data displayed starting with
[DST].
5-12
Chapter5 HOW TO OPERATE
Switching the travel data display (SC-E8000/SC-E6010)
Resetting the traveling distance (SC-E8000/SC-E6010)
You can clear the traveling distance in the main screen.
1
Change the traveling data display to [DST] and press Assist-A or the function button for 2 seconds.
2
Release the finger when the [DST] indication starts blinking.
In this state, pressing Assist-A or the function button again clears the traveling distance.
TECH TIPS
•
If left alone for 5 seconds, the [DST] indicator light stops blinking and the display returns to the basic screen.
•
When the traveling distance is cleared,
[TIME], [AVG] and [MAX] are also cleared.
5-13
Chapter5 HOW TO OPERATE
Switching the travel data display (SC-E6100)
Switching the travel data display (SC-E6100)
(A)
Traveling data display
(A)
(A)
(B)
[DST]
[ODO]
(C) [RANGE]
(D) [RANGE]
Assist
Function button
[CADENCE] (H)
[MAX] (G)
[AVG]
[TIME]
(F)
(E)
* The Walk assist mode function may not be able to be used in certain regions.
The type of travel data displayed changes each time you press Assist-A or the cycle computer's function button.
(A)
Traveling distance
(B)
Cumulative distance
(C)
Traveling range *1
(D)
Traveling range for each assist mode *1*2*3
(E)
Traveling time *3
(F)
Average speed *3
(G)
Maximum speed *3
(H)
Crank rotation speed *3 *4
*1
The battery level is not displayed while displaying the traveling range. Traveling range figures are approximations to be used for reference purposes only.
*2
This data is displayed as follows. Gear shifting mode and gear position are not displayed.
*3
Optional item: You can configure the display settings in E-TUBE PROJECT. For details, refer to the "CONNECTION AND
COMMUNICATION WITH DEVICES" section.
*4
Cadence is only displayed when pedaling is assisted while using electronic gear shifting.
5-14
Chapter5 HOW TO OPERATE
Switching the travel data display (SC-E6100)
Clearing the traveling distance (SC-E6100)
You can clear the traveling distance in the main screen. When the traveling distance is cleared, [TIME] (traveling time), [AVG] (average speed), [MAX]
(maximum speed) are also cleared.
Assist
Press Assist-A or function button to change the travel data display to [DST].
Function button
1
2
Assist
Function button
Press and hold down Assist-A or the function button until the value below the [DST] display blinks.
3
Press Assist-A or the function button again.
• Travel data is cleared.
• If nothing is done for five seconds after the number for [DST] begins flashing, it will stop flashing and the screen will return to the basic screen.
5-15
Chapter5 HOW TO OPERATE
Switching the travel data display (SC-E7000)
Switching the travel data display (SC-E7000)
(A)
(A)
Current speed display
(B)
Traveling data display
(B)
(A)
Current speed
(B)
(C)
(D)
(E)
[DST]
[ODO]
[RNG]
[TME]
A
Assist
Function button
[CLK]
[CAD]
[MAX]
[AVG]
(I)
(H)
(G)
(F)
* The Walk assist mode function may not be able to be used in certain regions.
The type of travel data displayed changes each time you press Assist-A or the cycle computer's function button.
(A)
Current speed
(B)
Traveling distance
(C)
Cumulative distance
(D)
Traveling range *1
(E)
Traveling time *2
(F)
Average speed *2
(G)
Maximum speed *2
(H)
Crank rotation speed *2*3
(I)
Current time *2
*1
The traveling range should be used as a reference only.
*2
Optional item: You can configure the display settings in E-TUBE PROJECT.
*3
Cadence is only displayed when pedaling is assisted while using electronic gear shifting.
5-16
Chapter5 HOW TO OPERATE
Switching the travel data display (SC-E7000)
Clearing the traveling distance (SC-E7000)
You can clear the traveling distance in the main screen. When the traveling distance is cleared, [TME] (traveling time), [AVG] (average speed), and [MAX]
(maximum speed) are also cleared.
1
Press Assist-A or the function button to switch the traveling data display to [DST].
2
Continue to hold Assist-A or the function button until the number displayed for [DST] flashes.
3
Press Assist-A or the function button again.
• The traveling data is cleared.
• If nothing is done for five seconds after the number for [DST] begins flashing, it will stop flashing and the screen will return to the basic screen.
5-17
Chapter5 HOW TO OPERATE
About the setting menus
About the setting menus
Accessing the setting menu (SC-E8000)
Hold down the function button when the bicycle is not moving to display the menu list screen.
1
Function button
Assist
Y X
2
(A)
(B)
Function button
[Clear] [Exit]
[Clock]
(L)
[RD protection reset]
(K)
[Adjust] (J) (C) [Bluetooth LE]
(D)
[Bluetooth LE/
ANT]
(E) [Light]
(F) [Brightness]
[Language]
[Unit]
[Beep]
(I)
(H)
(G)
Press Assist-X or Assist-Y to select the various menus.
Press the function button to display the setting screen for the selected menu.
(A)
Clear settings
(B)
Clock setting
(C)
Bluetooth LE pairing
(D)
Bluetooth LE/
ANT connection status
(E)
Turning the light on/off
(F)
Display backlight brightness setting
(G)
Turning the beep noise on/off
(H)
Switching between km and miles
(I)
Language setting
(J)
Adjusting the electronic gear shifting unit
(K)
Activating RD Protection Reset*
(L)
Return to the main screen
TECH TIPS
*
In order to protect the system when the bicycle falls and is subjected to a strong impact, the RD Protection function will activate and momentarily severe the connection between the motor and the link, impairing the proper function of the rear derailleur. Executing RD Protection
Reset restores the connection between the motor and the link, as well as the function of the rear derailleur.
5-18
Chapter5 HOW TO OPERATE
About the setting menus
Accessing the setting menu (SC-E6010)
1
Hold down Assist-X and Assist-Y when the bicycle is not moving to display the setting menu.
X
Assist
Y
(A) [Clear]
2
(B) [Clock]
(C) [Backlight]
(D) [Brightness]
(E) [Beep]
(F) [Unit]
X
Assist
Y
A
[Exit] (K)
[RD protection reset]
(J)
[Adjust] (I)
[Font color] (H)
[Language] (G)
Press Assist-X or Assist-Y to select the various menus. Press Assist-A to display the setting screen for the selected menu.
[Start mode] and [Auto] are displayed on the menu list screen; however, they are not available for use.
(A)
Clear settings
(B)
Clock setting
(C)
Turning the display backlight ON/
OFF
(D)
Display backlight brightness setting
(E)
Turning the beep noise ON/OFF
(F)
Switching between km and miles
(G)
Language setting
(H)
Changing the font color
(I)
Adjusting the electronic gear shifting unit
(J)
Activating RD Protection Reset*
(K)
Return to the main screen
TECH TIPS
*
In order to protect the system when the bicycle falls and is subjected to a strong impact, the RD Protection function will activate and momentarily severe the connection between the motor and the link, impairing the proper function of the rear derailleur. Executing RD Protection
Reset restores the connection between the motor and the link, as well as the function of the rear derailleur.
5-19
Chapter5 HOW TO OPERATE
About the setting menus
Accessing the setting menu (SC-E6100/SC-E7000)
Hold down Assist-X and Assist-Y when the bicycle is not moving to display the menu list screen.
Assist
X
Y
Y X
< SC-E6100 >
< Basic screen > < Setting menu screen >
1
< SC-E7000 >
< Basic screen >
< Setting menu screen >
To be continued on next page
5-20
Chapter5 HOW TO OPERATE
About the setting menus
X
Y
Assist
A
Assist
SC-E6100/SC-E7000
(A) [Clear]
2
(B) [Clock]
(C) [Backlight]
(D) [Brightness]
(E) [Light]
(F)
(G)
[Beep]
[Unit]
(H) [Language]
Function button
[Exit] (O)
[Display speed]
(N)
[RD protection reset]
(M)
[Shifting advice]
(L)
[Shift timing] (K)
[Adjust] (J)
[Font color] (I)
Press Assist-X or Assist-Y to select the various menus. Press the function button to display the setting screen for the selected menu.
[Start mode] and [Auto] are displayed on the menu list screen; however, they are not available for use.
(A)
Clear settings
(B)
Clock setting
(C)
Turning the display backlight on/ off (SC-E6100)
(D)
Display backlight brightness setting (SC-E6100)
(E)
Turning the light on/off (SC-
E7000)
(F)
Turning the beep noise on/off
(G)
Switching between km and miles
(H)
Language setting
(I)
Changing the font color
(J)
Adjusting the electronic gear shifting unit
(K)
Adjusting the timing at which gear shifting advice is displayed
(SC-E6100)
(L)
Adjusting the gear shifting timing
(SC-E6100)
(M)
Activating RD Protection Reset*
(N)
Adjusts the displayed speed to match another device.
(O)
Return to the main screen
TECH TIPS
*
In order to protect the system when the bicycle falls and is subjected to a strong impact, the RD Protection function will activate and momentarily severe the connection between the motor and the link, impairing the proper function of the rear derailleur. Executing RD Protection
Reset restores the connection between the motor and the link, as well as the function of the rear derailleur.
5-21
Chapter5 HOW TO OPERATE
About the setting menus
[Clear] Setting reset
Resets the traveling distance and display settings.
Assist
X
Y
Y X
SC-E8000
1
SC-E6010
Press Assist-X or Assist-Y to select [DST].
Configurable items
Details
[Exit]
Return to the menu list screen
[DST]
Reset the traveling distance
[Default]*
Reset the display settings
* SC-E6010/SC-E6100 only
When the display settings are reset, the following will be reset to their default settings.
Configurable items
Default value
[Backlight]
[ON]
[Beep]
[Unit]
[ON]
[km]
[Language]
[English]
[Brightness]
[3]
[Font color]
[White]
2
Y X
Assist
X
Y
Function button
To reset traveling distance, select [OK] using Assist-X or Assist-Y and press the function button to confirm.
After resetting, the screen will automatically return to the menu list screen.
A reset confirmation screen is not displayed on SC-E6010/SC-E7000/
SC-E6100.
TECH TIPS
When the traveling distance is reset, [TIME] /
[TME] (traveling time), [AVG] (average speed), and [MAX] (maximum speed) will also be reset.
5-22
Chapter5 HOW TO OPERATE
About the setting menus
[Clock] Time setting
Configure the clock setting.
Y X
Assist
X
Y
1
Press Assist-X or Assist-Y to adjust the time.
TECH TIPS
•
Press Assist-X to increase the numbers.
•
Press Assist-Y to decrease the numbers.
2
A
Assist
Function button
Pressing Assist-A or the function button enables the set value and moves you to the minutes setting.
3
Press Assist-X or Assist-Y to set the minutes.
4
Pressing Assist-A or the function button enables the set value and takes you back to the menu list screen.
TECH TIPS
You can change the numbers quickly by holding down Assist-X or Assist-Y.
5-23
Chapter5 HOW TO OPERATE
About the setting menus
[Bluetooth LE] (SC-E8000)
E-TUBE PROJECT for smartphones/tablets may be used if a Bluetooth
®
LE connection is established with a smartphone/tablet.
1
Before setting up a connection, turn on the Bluetooth LE function on the smartphone or tablet.
2
Open E-TUBE PROJECT and set it to listen for Bluetooth LE signals.
3
Assist
Y X
Function button
Press Assist-X or Assist-Y to select [Start].
To start Bluetooth LE pairing, press the function button to confirm.
If you press the function button during
Bluetooth LE pairing, the transmission will be interrupted, then the screen will return to the menu list screen.
Item
[Start]
[Cancel]
Details
Starts Bluetooth LE pairing
To not perform pairing, select
[Cancel]
TECH TIPS
Generally, Bluetooth LE transmission will begin automatically when the cycle computer is turned ON, however, pairing can be started by selecting [Start] from the [Bluetooth LE] menu when connectivity is poor.
(y)
4
To be continued on next page
(z)
When connection is successful, the
SHIMANO STEPS logo is displayed on screen.
If a connection is not successful, a message indicating this is displayed.
After a successful connection or a connection failure, press one of Assist-X/
Assist-Y/function button or the screen will automatically return to the setting menu after awhile.
(y)
Connection successful
(z)
Connection failed
5-24
Chapter5 HOW TO OPERATE
About the setting menus
5
When connection is successful, the unit name will display in E-TUBE PROJECT.
6
Select the unit name displayed on screen.
To disconnect, cancel the Bluetooth LE connection from the smartphone/tablet. (The cycle computer will exit connection mode and return to regular operation mode.)
5-25
Chapter5 HOW TO OPERATE
About the setting menus
[Bluetooth LE/ANT] Wireless connection status display
Current status of wireless connections can be displayed on screen.
For details on ANT connection, refer to "ANT connection" in the section "About wireless functions".
(x)
Select [Bluetooth LE/ANT] from the menu list screen and confirm to display current wireless connection status.
(x)
When connected via Bluetooth LE
(y)
When an ANT signal is being emitted
(z)
When neither Bluetooth LE nor
ANT is connected
(y)
(z)
[Light] Light ON/OFF (SC-8000/SC-E7000)
Turns the light connected to the drive unit ON/OFF.
Assist
Y X
Press Assist-X or Assist-Y to select the required setting.
[ON]
Item
[OFF]
Details
Keep light always on
Keep light always off
1
To be continued on next page
5-26
Chapter5 HOW TO OPERATE
About the setting menus
Assist
2
Function button
Press Assist-A or the function button to confirm the setting.
• After confirmation, the screen will automatically return to the menu list screen.
If using SW-E6010, this can also be operated with Assist-A.
5-27
Chapter5 HOW TO OPERATE
About the setting menus
[Light] Light ON/OFF (SC-E6010/SC-E6100)
When the drive unit is connected, push the light button on the cycle computer to turn the light on. An icon indicating that the light is on appears on the screen. Push the button again to turn the light off. Once the light is turned off, the icon on the screen disappears.
* If no light is connected to the drive unit and [Backlight] is set to [MANUAL], pressing the light button turns the cycle computer’s backlight on and off.
* When using SC-E8000/SC-E7000, the light can be operated from the setting menu.
Light button
TECH TIPS
•
The light turns OFF in conjunction with the power.
•
When the battery power is OFF, the light will not turn on.
When the light is turned on
When the light is turned off
Light ON/OFF (EW-EN100)
If a light is connected to the drive unit, the cycle computer or junction [A] can be used to operate the light. This section describes how to operate the light using EW-EN100.
(A)
(B)
Hold the button down until the light turns ON (around two seconds).
• When the light turns ON, LED1 will flash.
(A)
Button
(B)
LED1
TECH TIPS
•
The light turns OFF when the main power is turned OFF. The light will not turn ON when the main power is OFF.
•
The light cannot be turned OFF by pressing the button while riding.
5-28
Chapter5 HOW TO OPERATE
About the setting menus
[Backlight] Backlight setting (SC-E6010/SC-E6100)
Configure the display backlight.
X
Assist
Y
1
Press Assist-X or Assist-Y to select the required setting.
Configurable items
[ON]
[OFF]
[MANUAL]
Details
Keep light always on
Keep light always off
The light turns ON/
OFF in conjunction with the drive unit it is connected to
2
Assist
Press Assist-A or the function button to confirm the setting.
• After confirmation, the screen will automatically return to the menu list screen.
Function button
[Brightness] Backlight brightness setting (SC-E8000/SC-E6010/SC-E6100)
The brightness of the backlight can be adjusted as needed.
Assist
X
Y
Press Assist-X or Assist-Y to adjust the brightness.
Y X
1
TECH TIPS
The brightness can be adjusted in 5 levels.
2 A
Assist
Function button
Press Assist-A or the function button to confirm the adjusted value.
• After confirmation, the screen will automatically return to the menu list screen.
5-29
Chapter5 HOW TO OPERATE
About the setting menus
[Beep] Beep setting
The beep noise can be turned on/off.
Assist
X
Y
Y X
1
Press Assist-X or Assist-Y to select the required setting.
[ON]
Item
[OFF]
Details
Enable beeps
Disable beeps
TECH TIPS
Even when [Beep] is set to [OFF], a beep will sound when there is a misoperation, system error, etc.
2 A
Assist
Function button
Press Assist-A or the function button to confirm the setting.
• After confirmation, the screen will automatically return to the menu list screen.
5-30
Chapter5 HOW TO OPERATE
About the setting menus
[Unit] Km/mile switch
Distance units (km/miles) can be switched.
Assist
X
Y
Y X
1
Press Assist-X or Assist-Y to select the required setting.
[km]
Item
[mile]
Details
Displays in km
Displays in miles
2 A
Assist
Function button
[Language] Language setting
Configure the language setting.
Assist
X
Y
Y X
1
2
A
Assist
Press Assist-A or the function button to confirm the setting.
• After confirmation, the screen will automatically return to the menu list screen.
Press Assist-X or Assist-Y to select the required setting.
Language
English
French
German
Dutch
Italian
Spanish
Press Assist-A or the function button to confirm the setting.
• After confirmation, the screen will automatically return to the menu list screen.
Function button
5-31
Chapter5 HOW TO OPERATE
About the setting menus
[Font color] Font color setting (SC-E6010/SC-E6100/SC-E7000)
Switches the font color between black and white.
X
Assist
Y
White Black
1
Press Assist-X or Assist-Y to select the required setting.
Configurable items
[White]
[Black]
2
A
Assist
Function button
Press Assist-A or the function button to confirm the setting.
• After confirmation, the screen will automatically return to the menu list screen.
5-32
Chapter5 HOW TO OPERATE
About the setting menus
[Shift timing] Display timing setting (SC-E6100)
Set the timing at which gear shifting advice is displayed.
X
Assist
Y
1
Press Assist-X or Assist-Y to adjust the values.
• Pressing Assist-X to increase the value adjusts the display timing to make pedaling easier.
• Pressing Assist-Y to decrease the value adjusts the display timing to make pedaling harder.
2
Assist
Function button
Press Assist-A or the function button to confirm the setting.
* The screen will automatically return to the setting menu screen.
5-33
Chapter5 HOW TO OPERATE
About the setting menus
[Shifting advice] Shifting advice setting (SC-E6100)
Sets whether to display the recommended gear shifting timing on the cycle computer during manual gear shifting.
1
X
Y
Assist
Press Assist-X or Assist-Y to move the cursor to the item you want to configure.
Configurable items
Details
[ON]
[OFF]
Enables the gear shifting advice function, which displays an icon to notify the user of the recommended timing for gear shifting during manual gear shifting.
Disable the shifting advice function
2
Assist
Press Assist-A or the function button to confirm the setting.
* The screen will automatically return to the setting menu screen.
Function button
5-34
Chapter5 HOW TO OPERATE
About the setting menus
[Adjust] Gear shifting adjustment with the electronic gear shifting unit
Gear shifting adjustment is performed with the electronic gear shifting unit.
CAUTION
Perform adjustment only when gear shifting feels unusual.
Under normal conditions, performing unnecessary adjustment may worsen gear shifting performance.
Improper adjustment may cause gear engagement skipping, resulting in an accidental fall.
< SC-E8000 >
Open the Adjust screen and check whether the adjustment value is set to
[0].
< SC-E6100 >
The settings have a range of -16 to 16.
TECH TIPS
5-35
Chapter5 HOW TO OPERATE
About the setting menus
If the adjustment value is [0]
Shift
X
Y
< SC-E8000 >
X Y
Press Shift-X or Shift-Y to adjust the adjustment value up or down by 1 speed.
1
< SC-E6100 >
2
A
Assist
Function button
Press Assist-A or the function button and after selecting [OK], adjust by rotating the crank.
Shift gears to check whether the condition has improved.
To be continued on next page
5-36
Chapter5 HOW TO OPERATE
About the setting menus
The condition has improved
Adjust the adjustment value by 1 speed in the same direction and check the gear shifting operation again.
Repeat these steps until any noise or unusual feeling disappears.
< SC-E8000 > < SC-E6100 >
3
3
No apparent change
Adjust the adjustment value by 1 speed in the same direction and check the gear shifting operation again.
If the condition has improved, see
"The condition has improved"
to continue.
If the condition has worsened, see
"The condition has worsened"
to continue.
< SC-E8000 > < SC-E6100 >
To be continued on next page
5-37
Chapter5 HOW TO OPERATE
About the setting menus
The condition has worsened
Adjust the adjustment value by 2 speeds in the opposite direction and check the gear shifting operation again.
Then, adjust the value by 1 speed in the same direction and check until any noise or unusual feeling is gone.
< SC-E8000 > < SC-E6100 >
3
4
Finally, go for an actual ride and check for any noise or unusual feeling.
If the adjustment value is not [0]
Press Shift-X or Shift-Y and revert the adjustment value to [0].
Shift
X
Y
< SC-E8000 >
X Y
< SC-E6100 >
1
To be continued on next page
5-38
Chapter5 HOW TO OPERATE
About the setting menus
Function button
A
Assist
2
Press Assist-A or the function button and after selecting [OK], adjust by rotating the crank.
Shift gears to check whether the condition has improved.
If there is any noise or unusual feeling, see
"If the adjustment value is [0]"
to continue.
3
Finally, go for an actual ride and check for any noise or unusual feeling.
[RD protection reset] Reset RD protection
In order to protect the system when the bicycle falls and is subjected to a strong impact, the RD Protection function will activate and momentarily severe the connection between the motor and the link, impairing the proper function of the rear derailleur. Executing RD Protection Reset restores the connection between the motor and the link, as well as the function of the rear derailleur.
1
Y X
Assist
X
Y
Press Assist-X or Assist-Y to select [OK].
[OK]
Item
[Cancel]
Details
RD Protection Reset will operate
Returns to the setting menu.
2
A
Assist
Function button
Press Assist-A or the function button and after selecting [OK], recover the connection between the motor and the link by rotating the crank.
5-39
Chapter5 HOW TO OPERATE
About the setting menus
[Display speed] Adjusting the display speed (SC-E6100/SC-E7000)
Adjusts the displayed speed when there is a difference between the speed displayed on the cycle computer and other devices.
If the display on the cycle computer is adjusted, the actual speed may be higher than the displayed speed. Keep this in mind if riding in an area with a speed limit.
Assist
Press Assist-X or Assist-Y to adjust the number.
• Press Assist-X to increase the number.
The number displayed for the speed increases.
• Press Assist-Y to decrease the number.
The number displayed for the speed decreases.
< SC-E6100 >
1
< SC-E7000 >
2
A
Assist
Press Assist-A or the function button to confirm the setting.
* The screen will automatically return to the setting menu screen.
Function button
[Exit] Close setting menu screen
Returns to the basic screen.
1
Press Assist-X or Assist-Y to select [Exit] on the setting menu screen.
2
Press Assist-A or the function button to confirm. After confirmation, the screen will return to the basic screen.
5-40
Chapter5 HOW TO OPERATE
About the setting menus
Update confirmation window for the drive unit settings backup data (SC-E8000/SC-E6010)
The cycle computer has a function to automatically back up drive unit settings.
In the following cases, when the cycle computer power is turned ON, a window confirming whether to update the backup data is displayed:
• Reinstalling the cycle computer on a bicycle with different settings
• If the drive unit settings have been changed via E-TUBE PROJECT
< SC-E8000 >
To update the drive unit settings select
[Yes], to cancel update select [No].
< SC-E6010 >
If the settings cannot be accessed due to a drive unit malfunction, they can be accessed using E-TUBE PROJECT.
5-41
Chapter5 HOW TO OPERATE
Setting Mode (EW-EN100)
Setting Mode (EW-EN100)
It is impossible to switch to the setting mode when riding the bicycle.
RD protection reset
In order to protect the system when the bicycle falls and is subjected to a strong impact, the RD Protection function will activate and momentarily severe the connection between the motor and the link, impairing the proper function of the rear derailleur. Executing RD Protection Reset restores the connection between the motor and the link, as well as the function of the rear derailleur.
(A)
(B)
(C)
Hold the button down (for roughly eight seconds) until LED1 flashes red.
• Once LED1 is flashing, release the button. When only LED1 is flashing red, the system is in the RD protection reset mode.
(A)
Button
(B)
LED1
(C)
LED2
1
NOTICE
Mount the bicycle to a maintenance stand or otherwise secure it in place so that the rear wheel can be spun freely.
2
Turn the crank arm.
• The rear derailleur moves, and the connection between the motor and link is restored.
Adjust
Adjust gear shifting for the electronic gear shifting rear derailleur.
• A switch unit configured as a shifting switch is required to set this.
Turn the main power ON.
1
Shift the rear derailleur to the fifth gear position from the largest sprocket.
NOTICE
•
Mount the bicycle to a maintenance stand or otherwise secure it in place so that the rear wheel can be spun freely.
•
Perform adjustment only when gear shifting feels unusual. Under normal conditions, performing unnecessary adjustment may worsen gear shifting performance.
(A)
Largest sprocket
(B)
Guide pulley
2
(A)
(B)
To be continued on next page
5-42
Chapter5 HOW TO OPERATE
Setting Mode (EW-EN100)
3
(A)
(B)
(C)
Hold the button down (for roughly five seconds) until LED1 lights up red.
• Once LED1 is flashing, release the button. When only LED1 is flashing red, the system is in the adjust mode.
(A)
Button
(B)
LED1
(C)
LED2
NOTICE
Note that if you keep pressing the button after LED1 lights up red, LED1 will flash red and RD protection reset will start.
Shift
Y
Y
Press Shift-Y while turning the crank, and move the guide pulley toward the largest sprocket.
• Move it to the position where the chain makes contact with the fourth gear and a subtle noise is heard.
TECH TIPS
The guide pulley can move 16 steps inward and 16 steps outward from the initial position, for a total of 33 positions.
4
X
Shift
X
Press Shift-X five times to move the guide pulley five steps toward the smallest sprocket.
• This position will serve as the target for adjustment.
5
To be continued on next page
5-43
Chapter5 HOW TO OPERATE
Setting Mode (EW-EN100)
6
(A) (B)
Press the EW-EN100 button.
• The adjustment change is finalized and the system exits adjust mode.
7
Press Shift-X and Shift-Y while turning the crank, and try shifting gears.
• If fine adjustment is required, return to step 3 and repeat the rear derailleur adjustment process.
(A)
Button
(B)
LED1
5-44
Chapter5 HOW TO OPERATE
Error messages on the cycle computer
Error messages on the cycle computer
Warnings
< SC-E8000 >
If the situation is resolved, this indication will disappear. If the situation does not improve, consult an agency.
< SC-E7000 >
< SC-E6010 > < SC-E6100 >
List of warnings
Code
W010
W011
W013
W020
Display preconditions
Operational restrictions while warning is displayed
Temperature of the drive unit is higher than it is during times of normal operation.
Power assistance may be lower than usual.
Remedy
Stop using the assist function until the temperature of the drive unit drops.
The traveling speed cannot be detected.
The maximum speed up to which power assistance is provided may be lower than usual.
Check the following:
• Whether the speed sensor is installed in the correct position.
• Whether the magnet included with the disc brake rotor has not come off.
Refer to the Disc Brake section of General Operations for steps on reattaching the magnet.
With your foot off the pedal, press the battery power button and turn on the power again.
Initialization of torque sensor was not completed successfully.
If the temperature exceeds the guaranteed operating range, the battery output is turned
OFF.
Power assistance may be lower than usual.
No system functions will start.
If it has exceeded the temperature in which discharge is possible, leave the battery in a cool place away from direct sunlight until the internal temperature of the battery decreases sufficiently. If it is below the temperature in which discharge is possible, leave the battery indoors, etc. until its internal temperature is at a suitable temperature.
5-45
Chapter5 HOW TO OPERATE
Error messages on the cycle computer
Code
W032
Display preconditions
An electronic derailleur may have been installed in place of a mechanical derailleur.
Operational restrictions while warning is displayed
Power assistance provided in
[WALK] mode may be lower than usual.
* The Walk assist mode function may not be able to be used in certain regions.
Remedy
Reinstall the derailleur for which the system is configured to support.
Errors
< SC-E8000 >
If an error message is displayed on the entire screen, follow one of the procedures below to reset the display.
• Press the power switch of the battery.
• Remove the battery from the mount.
NOTICE
If the situation does not improve even after turning the power back ON, consult with a distributor.
< SC-E7000 >
< SC-E6010/SC-E6100 >
List of errors
Code
E010
E013
E014
Display preconditions
A system error was detected.
An error was detected in the drive unit’s firmware.
The speed sensor may have been installed in the wrong position.
Operational restriction when an error is being displayed
Power assistance is not provided during riding.
Remedy
Press the power switch of the battery to turn on the power again.
Power assistance is not provided during riding.
Consult an agency.
Power assistance is not provided during riding.
Check whether the speed sensor is installed in the correct position.
If the speed sensor is not in the correct position, the error will be resolved by installing it in the correct position and riding the bicycle for a little while.
5-46
Chapter5 HOW TO OPERATE
Error messages on the cycle computer
Code
E020
E021
E022
E023
E024
E025
E033
E043
Display preconditions
Operational restriction when an error is being displayed
A communication error between the battery and drive unit was detected.
Battery connected to drive unit conforms with system standards but is not supported.
Battery connected to drive unit does not conform with system standards.
Electrical failure inside the battery.
Communication error with the bicycle system.
This is displayed when a genuine drive unit is not connected.
This is displayed if any of the cables are disconnected.
The current firmware doesn’t support system operation.
The cycle computer’s firmware may be partially corrupt.
Power assistance is not provided during riding.
Power assistance is not provided during riding.
No system functions will start.
No system functions will start.
No system functions will start.
No system functions will start.
Power assistance is not provided during riding.
Power assistance is not provided during riding.
Remedy
Check that the cable between the drive unit and battery is properly connected.
Press the power switch of the battery to turn on the power again.
Press the power button of the battery to turn it on again.
Press the battery power button to turn the power ON again.
Make sure that the cable is not loose or improperly connected.
Connect a genuine battery and drive unit.
Check the condition of the cables.
Connect to E-TUBE PROJECT and update firmware for all unit.
Consult an agency.
5-47
Chapter5 HOW TO OPERATE
EW-EN100 Error Indication
Maintenance alert (SC-E6100/SC-E7000)
< SC-E6100 >
This notifies the user that the bicycle requires maintenance. An icon is displayed on the cycle computer screen when the bicycle reaches the set odometer or date. You must connect to
E-TUBE PROJECT to configure this setting. Refer to the help manual for
E-TUBE PROJECT for details.
< SC-E7000 >
EW-EN100 Error Indication
When an error occurs, the two LEDs on EW-EN100 will quickly flash red at the same time.
(A)
(B)
If this occurs, follow one of the procedures below to reset the indication.
• Press the battery power switch to turn the power OFF.
• Remove the battery from the mount.
If the situation does not improve even after turning the power back ON, consult with a distributor.
(A)
LED1
(B)
LED2
5-48
Chapter6 CONNECTION AND
COMMUNICATION WITH DEVICES
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
About wireless functions
CONNECTION AND COMMUNICATION WITH DEVICES
The system can be configured and firmware can be updated when the bicycle is connected to a device.
You need E-TUBE PROJECT to configure SHIMANO STEPS and update firmware.
Download E-TUBE PROJECT from our support website (
https://e-tubeproject.shimano.com
).
For information on how to install E-TUBE PROJECT, check the E-TUBE support website.
NOTICE
•
You need SM-PCE1 and SM-JC40/SM-JC41 to connect SHIMANO STEPS to a PC. They are not required if there is an available port.
•
Firmware is subject to change without notice.
•
PC connection and communication are not possible during charging.
•
Connecting to devices is not possible while charging.
About wireless functions
Functions
ANT connection (SC-E8000/SC-E7000/SC-E6100)
The wireless unit can send all information displayed on the basic screen of the cycle computer to an external device.
TECH TIPS
The latest functions can be checked by updating the software via E-TUBE PROJECT.
For details, consult the place of purchase.
Bluetooth
®
LE connection (SC-E8000/SC-E7000/SC-E6100/EW-EN100)
The wireless unit can send all information displayed on the basic screen of the cycle computer to an external device.
E-TUBE PROJECT for smartphones/tablets may be used if a Bluetooth
®
LE connection is established with a smartphone/tablet. SC-E7000/SC-E6100/
EW-EN100 are compatible with E-TUBE RIDE, which can be used to check traveling data on a smartphone connected over Bluetooth LE.
6-2
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
2.4 GHz digital wireless system
How to make connections
ANT connection (SC-E8000/SC-E7000/SC-E6100/EW-EN100)
When the main power is turned ON for SHIMANO STEPS, communication can be received at any time. Switch the external device to connection mode and then connect it. For SC-E8000, you can check [Bluetooth LE/ANT] to confirm whether the connection was successful.
Bluetooth ® LE connection (SC-E8000)
Generally, Bluetooth LE transmission will begin automatically when the cycle computer is turned ON, however, pairing can be started by [Bluetooth LE] menu when connectivity is poor.
Bluetooth
®
LE connection (SC-E7000/SC-E6100/EW-EN100)
Communication can only be received under the following conditions. Switch the external device to connection mode in advance.
• Within 15 seconds of the main power for SHIMANO STEPS turning ON.
• Within 15 seconds of operating any button other than the SHIMANO STEPS power switch.
2.4 GHz digital wireless system
2.4 GHz-frequency digital wireless technology, which is the same technology used for wireless LAN.
However, on very rare occasions, objects and places may generate strong electromagnetic, waves and interference, which may result in incorrect measurement.
• Television, PC, radios, motors/engines, or in car and trains.
• Railroad crossings and near railway tracks, around television transmitting stations and radar bases.
• Other wireless computers or digitally controlled light.
Drive unit setting backup function for the cycle computer
To check the drive unit settings backed up to the cycle computer, export the PDF report from the E-TUBE PROJECT [Unit log acquisition] menu. When exchanging the drive unit, send the report along with the unit to your place of purchase or a local bicycle dealer.
6-3
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Settings customizable in E-TUBE PROJECT
Settings customizable in E-TUBE PROJECT
< SC-E8000 >
Drive unit setting
Light connection
Sets whether to use a light.
Display monitor settings
Other functions
Display units
Display switchover
Time setting
Beep setting
Backlight brightness setting
Display language
Switches the display unit between km and mile.
You can select whether to display the items Traveling time, Average speed, Maximum speed, Cadence
(crank rotation speed) and Range overview.
Sets the time.
Switches the beep sound ON or OFF.
The backlight’s brightness can be adjusted.
You can choose from English, French, German, Dutch, Spanish, and Italian.
• Error check
• Update firmware
• Preset
• Unit log acquisition
* For details, download E-TUBE PROJECT and refer to the manual provided.
6-4
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Settings customizable in E-TUBE PROJECT
< SC-E6010 >
Switch function setting
Changes the functions to assign to switches A, X, and Y of SW-E6010. Functions that can be assigned vary depending on the type of switch.
• The same function cannot be assigned to different switches.
Sets SW-E6010 to be used for either assist mode switching or gear shifting.
Switch mode setting
Drive unit setting
Light connection
Display monitor settings
Display units
Time setting
Backlight setting
Backlight brightness setting
Beep setting
Display language
Font color setting
Traveling time
Average speed
Maximum speed
Range overview
Other functions
Sets whether to use a light.
Switches the display unit between km and mile.
Sets the time.
Switches the backlight of the cycle computer ON or OFF.
The backlight’s brightness can be adjusted.
Switches the beep sound ON or OFF.
You can choose from English, French, German, Dutch, Spanish, and Italian.
The font color can be set to white or black.
Switches the traveling time indication ON or OFF.
Switches the average speed indication ON or OFF.
Switches the maximum speed indication ON or OFF.
Switches the traveling range list indication ON or OFF.
• Error check
• Update firmware
• Preset
• Unit log acquisition
* For details, download E-TUBE PROJECT and refer to the manual provided.
6-5
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Settings customizable in E-TUBE PROJECT
< SC-E6100/SC-E7000 >
Switch function setting
Light connection
Drive unit setting
Maintenance alert
Assigns functions to each operation switch on the switch unit.
Sets whether a light is connected to the drive unit.
Gear shifting timing
*1
Gear shifting advice
*2
Adjusts the gear shifting timing during automatic gear shifting.
Also sets the timing at which gear shifting advice is displayed.
Sets whether to display the recommended gear shifting timing on the cycle computer during manual gear shifting.
Riding characteristics
Selects the output characteristics of the drive unit.
Maximum assist speed
Assist is provided up to the set speed. The maximum assist speed is determined by law, depending on the country of use.
Notifies the user when maintenance is required by displaying an icon on the cycle computer when the set odometer or date is reached.
Display settings
Display units
Time setting
Backlight setting
Backlight brightness setting
Beep setting
Switches between displaying km or miles.
Sets the time displayed on the cycle computer.
Turns the display backlight ON/OFF.
Sets the display brightness.
Display language
Font color setting
Traveling data display
Turns the operation sound ON/OFF.
Sets the display language.
Switches the font color between black and white.
Sets whether to display each item (traveling time, average speed, maximum speed, cadence (crank rotation speed), and traveling range) on the cycle computer.
Multi shift mode setting *3
Other functions
When a switch unit is used as a shifting switch, this sets the maximum number of gears that can be shifted by holding the switch down.
• Error log
• Update firmware
• Preset
• Acquire unit log
*1
Only for electronic gear shifting.
*2
Only for electronic gear shifting with the gear shifting mode set to [Manual].
*3
Electronic gear shifting rear derailleur models only.
NOTICE
When the SC-E6010 firmware is updated, the time set for the cycle computer is reset to match the computer’s clock.
6-6
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Connecting to the PC
Connecting to the PC
When connecting only individual units
Connect SM-PCE1/SM-PCE02 to the connector of each unit.
(A)
(B)
(D)
SM-PCE1
SM-PCE02
SM-JC40/SM-JC41
(C)
(A)
Drive unit
(B)
Cycle computer
(C)
Junction [A]
(D)
Switch unit
NOTICE
•
SM-JC40 or SM-JC41 is required to connect a single switch unit to a PC.
•
Individual units cannot be connected via wireless connection.
6-7
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Connecting to the PC
Connecting to the bicycle
< SC-E8000/SC-E7000 >
Connect SM-PCE1/SM-PCE02 to an available port of the cycle computer.
(A)
Switch unit
(B)
Drive unit
SM-PCE1/SM-PCE02
(B) (A)
When using electronic gear shifting
First, connect SM-JC40/SM-JC41 to SM-PCE1/SM-PCE02.
Then, disconnect the electric wire from the center port of the cycle computer and connect it to SM-JC40/SM-JC41.
(A)
Assist switch
(B)
Drive unit
(C)
Shift switch
SM-PCE1/SM-PCE02
SM-JC40/SM-JC41
(A)(B)(C)
6-8
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Connecting to the PC
< SC-E6010/SC-E6100 >
< When the cycle computer has an available port >
Connect SM-PCE1/SM-PCE02 to an available port of the cycle computer.
SM-PCE1/SM-PCE02
(A)
(B)
(A)
Switch unit
(B)
Drive Unit
< When the cycle computer has no available port >
First, connect SM-JC40/SM-JC41 to SM-PCE1/SM-PCE02.
Then, disconnect the electric wire from the center port of the cycle computer and connect it to SM-JC40/SM-JC41.
SM-PCE1/SM-PCE02
(A)
Switch unit
(B)
Drive Unit
1
(A)
(A)
SM-JC40/SM-JC41
(B)
Connect the electric wire to the available port of SM-JC40/SM-JC41 and the center port of the cycle computer.
2
6-9
Chapter6 CONNECTION AND COMMUNICATION WITH DEVICES
Connecting to the PC
< EW-EN100 >
< When junction [A] has a free port >
Connect as follows if EW-EN100 is not connected to anything other than a drive unit.
1
Remove the dummy plug from a free port on EW-EN100.
Connect the free port on EW-EN100 with the PC linkage device.
(A)
Drive unit
2
SM-PCE1
SM-PCE02
EW-EN100
< When junction [A] does not have a free port >
Connect as follows if a switch unit is connected and there are no free E-TUBE ports on EW-EN100.
1
Connect SM-JC40/SM-JC41 to the PC linkage device.
2
Disconnect the electric wire connected to the drive unit from EW-EN100, and connect it to
SM-JC40/SM-JC41.
Connect a free port on EW-EN100 and SM-JC40/SM-JC41 using an electric wire.
(A)
(A)
Switch unit
(B)
Drive unit
3
(A)
(B)
SM-PCE1
SM-PCE02
SM-JC40/SM-JC41
6-10
Chapter7 MAINTENANCE
Chapter7 MAINTENANCE
Replacing the clamp band (SC-E7000/SC-E8000)
MAINTENANCE
Replacing the clamp band (SC-E7000/SC-E8000)
Remove the case fixing bolt with a
2.5 mm hexagon wrench and replace the clamp band.
(A) (B) (C)
(A)
Clamp band
(B)
Washer
(C)
Case fixing bolt
Tightening torque
0.6 N·m
NOTICE
< SC-E8000 >
If using a handlebar with a thick diameter, reinstall it using the included Ø35 mm clamp band.
7-2
Chapter7 MAINTENANCE
Replacing the chainring unit
Replacing the chainring unit
1
Perform procedures with the chain installed to the rear wheel.
Attach the left and right crank arms using TL-FC16.
While holding the wheel, use the
SHIMANO original tool to loosen the lock ring in the direction shown in the illustration.
2
(A) (B)
(A)
TL-FC39/TL-FC36
(B)
Lock ring
NOTICE
•
If using a torque wrench, use TL-FC39 in combination with TL-FC33.
TL-FC39 TL-FC33
•
An impact wrench cannot be used.
3
Remove and then replace the chainring unit.
To install a chainring unit, refer to "INSTALLING AND WIRING THE DRIVE UNIT" and
"Installing the crank and chainring unit".
Refer to "Replacing the Chainring" when replacing the chainring.
7-3
Chapter7 MAINTENANCE
Replacing the chainring
Replacing the chainring
The chainring has a correct orientation.
Refer to "Replacing the Chainring Unit" for information on how to remove the chainring unit.
1
Remove the chainring unit.
Remove the chainring, and then replace it with a new chainring.
(D)
(C)
(B)
2
(A)
(A)
Gear fixing bolt
Use TL-FC23.
(B)
Chainring
(C)
4 arm adapter
(D)
Gear fixing nut
Use TL-FC22.
Tightening torque
12 - 14 N·m
NOTICE
•
Install the chainring so that "INSIDE" or the printed model name is on the 4-arm adapter side.
XXXXX-XX
•
The 4 bolts should be tightened uniformly over the course of multiple times rather than fully tightened at once.
7-4
Chapter7 MAINTENANCE
Replacing the guide of the chain device
Replacing the chain guard (SM-CRE80 44T Double chain guard)
Replace the chain guard as shown in the illustration.
(A) (B)
(A)
Chain guard fixing bolt
(B)
Chain guard
Tightening torque
0.7 N·m
Replacing the guide of the chain device
/
(C)
Loosen the guide fixing bolt (M5) to remove the guide from the back plate, and then replace it.
(A)
Guide
(B)
Guide fixing bolt (M5)
(C)
Back plate
NOTICE
•
A chain device cannot be used with
SM-CRE80 (44T CL: 50 mm Double chain guard).
•
When replacing it, use the included guide fixing bolt.
(A) (B)
7-5
Please note: specifications are subject to change for improvement without notice. (English)
© Nov. 2019 by SHIMANO INC. ITP
advertisement
Key Features
- Specifically designed for installing and removing Hollowtech II bottom bracket cups
- Long handle provides increased leverage for easier installation and removal
- Wide, ergonomic grip for comfort and control
- Durable construction for long-lasting use
Frequently Answers and Questions
What type of bottom bracket cups is the Shimano TL-FC39 designed for?
Does the Shimano TL-FC39 have a long handle?
What is the grip of the Shimano TL-FC39 like?
Related manuals
advertisement
Table of contents
- 6 TO ENSURE SAFETY
- 11 LIST OF TOOLS TO BE USED
- 15 INSTALLATION
- 15 Names of parts
- 16 Product specifications
- 17 Installing and removing the cycle computer (SC-E8000/SC-E7000)
- 19 Installing and removing the cycle computer (SC-E6010/SC-E6100)
- 21 Adjusting the angle of the cycle computer (SC-E6010/SC-E6100)
- 21 Installing junction [A] (EW-EN100)
- 23 Installing the switch unit
- 26 Connecting the electric wire
- 30 Installing the battery mount
- 39 Installing / removing the battery
- 43 Installing the speed sensor
- 44 Mounting the magnet
- 47 INSTALLING AND WIRING THE DRIVE UNIT
- 47 Installing the drive unit
- 48 Drive unit wiring diagram
- 49 Connecting the power cord
- 50 Connecting switches and the drive unit to the cycle computer (SC-E8000/SC-E7000)
- 50 Connecting the assist switch and drive unit to the cycle computer (SC-E6010/SC-E6100)
- 51 Connecting the switch unit and drive unit to junction [A] (EW-EN100)
- 52 Connecting the speed sensor to the drive unit
- 53 Connecting the light cable to the drive unit
- 54 Installing the crank and chainring unit
- 61 CHARGING THE BATTERY
- 61 Proper use of the battery
- 62 Charging the battery
- 64 About the charger LED lamp
- 64 About the battery LED lamps
- 67 Turning the power ON / OFF
- 70 HOW TO OPERATE
- 70 Cycle computer and switch units
- 71 Junction [A]
- 72 Basic screen display of the cycle computer
- 73 Displaying the basic status of junction [A]
- 74 Battery level indicator
- 75 Switching the assist mode
- 76 Walk assist mode
- 80 Switching the travel data display (SC-E8000/SC-E6010)
- 82 Switching the travel data display (SC-E6100)
- 84 Switching the travel data display (SC-E7000)
- 86 About the setting menus
- 110 Setting Mode (EW-EN100)
- 113 Error messages on the cycle computer
- 116 EW-EN100 Error Indication
- 118 CONNECTION AND COMMUNICATION WITH DEVICES
- 118 About wireless functions
- 119 2.4 GHz digital wireless system
- 119 Drive unit setting backup function for the cycle computer
- 120 Settings customizable in E-TUBE PROJECT
- 123 Connecting to the PC
- 128 MAINTENANCE
- 128 Replacing the clamp band (SC-E7000/SC-E8000)
- 129 Replacing the chainring unit
- 130 Replacing the chainring
- 131 Replacing the guide of the chain device