Shimano SC-E6100 Cycle Computer User's Manual
Shimano SC-E6100 is a cycle computer that provides various data and functions to enhance your cycling experience. With its user-friendly interface, you can easily view speed, distance, time, and other essential information during your rides. Additionally, it features wireless connectivity, allowing you to pair sensors and adjust settings through the E-TUBE PROJECT app. Whether you're a fitness enthusiast or a casual rider, the SC-E6100 offers valuable insights to help you track your progress and make the most of your cycling adventures.
विज्ञापन
विज्ञापन
UM-78S0A-000
SHIMANO Total Electric Power System
SC-E6100 User's Manual
Cycle Computer
CONTENTS
Regular inspections before riding the bicycle ....................................................4
Installing and removing the cycle computer ......................................................9
1
2
IMPORTANT NOTICE
• Contact the place of purchase or a distributor for information on installation, adjustment, and replacement of the products which are not found in the user's manual.
A dealer's manual for professional and experienced bicycle mechanics is available on our website (https://si.
shimano.com).
• Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a dealer.
• The Bluetooth
®
word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by SHIMANO INC. is under license.
Other trademarks and trade names are those of their respective owners.
For safety, be sure to read this "user's manual" thoroughly before use, follow it for correct use, and store it so that it can be referenced at any time.
The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings. The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
Failure to follow the instructions could result in death or serious injury.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
Important Safety Information
WARNING
• Do not disassemble or modify the product. This may cause the product to not operate correctly, and you may suddenly fall and be seriously injured.
Riding precautions
• Do not to pay excessive attention to the cycle computer display while riding.
Doing so may result in an accident.
• Confirm that the light works before riding.
Safety precautions
• Be sure to remove the battery and charging cable before wiring or attaching parts to the bicycle.
Failure to do so may cause an electric shock.
• Be sure to follow the instructions provided in the manuals when installing the product.
It is recommended that you use SHIMANO genuine parts.
Loose nuts or bolts and product damage may cause a sudden accident such as a fall and lead to serious injury.
• Do not leave this product in an extremely high temperature surrounding environment such as in a closed vehicle on a hot day, or near a heater. That can result in an explosion of the incorporated battery or the leakage of flammable liquid or gas from it.
• Do not subject this product to extremely low air pressure.
That may result in an explosion of incorporated battery or the leakage of flammable liquid or gas from it.
Transporting this product by air is not a problem.
Disposal precautions
• Observe all federal, state and local environmental regulations when disposing of this product, because it incorporates a battery. Disposal of this product into fire or a hot oven, or mechanically crushing or cutting of it, that can result in an explosion of the incorporated battery.
CAUTION
Riding precautions
• Observe the instructions in the manual for the bicycle in order to ride safely.
Safety precautions
• Never modify the system.
Doing so may cause a system error.
• Use the product under the supervision of someone responsible for safety and upon receiving usage instructions.
Do not allow anyone with reduced physical, sensual, or mental capacity, or those without experience or knowledge, to use the product, including children.
3
• Do not allow children to play near the product.
NOTICE
Safety precautions
• If any malfunction or trouble occurs, consult the place of purchase nearest you.
•
Be sure to attach caps to any unused connectors.
•
For installation and adjustment of the product, consult a place of purchase.
• The components are designed to be fully waterproofed to withstand wet weather riding conditions; however, do not deliberately place them into water.
• Do not clean the bicycle with a high-pressure washer. If water gets into any of the components, operating problems or rusting may result.
• Do not turn the bicycle upside down. There is a risk of damage to the cycle computer and switch unit.
• Handle the components carefully, and avoid subjecting them to strong shock.
• Although the bicycle still functions as a normal bicycle even when the battery is removed, the light will not turn on if it is connected to the electric power system. Be aware that using the bicycle under these conditions will be considered non-observance of the road traffic laws in
Germany.
Connection and communication with PC
A PC linkage device can be used to connect a PC to the bicycle (system or components), and E-TUBE PROJECT can be used to carry out tasks such as customizing single components or the whole system and updating firmware.
• PC linkage device: SM-PCE1/SM-PCE02
• E-TUBE PROJECT: PC application
• Firmware: Software inside each component
Connection and communication with smartphone or tablet
• It is possible to customize single components or the system, and update firmware, using E-TUBE PROJECT for smartphones/tablets after connecting the bicycle (system or components) to a smartphone or tablet via Bluetooth ®
LE.
• E-TUBE PROJECT: Application for smartphones/tablets
• Firmware: Software inside each component
Care and maintennce
• Contact the place of purchase for updates of the component software. The most up-to-date information is available on the SHIMANO website.
• Do not use thinner or other solvents to clean any of the components. Such substances may damage the surface.
• For any questions regarding methods of installation and maintenance, please contact your place of purchase.
• Products are not guaranteed against natural wear and deterioration from normal use and aging.
•
For maximum performance we highly recommend
SHIMANO lubricants and maintenance products.
Labels
• Some of the important information contained in this user's manual is also indicated on the device label.
Regular inspections before riding the bicycle
Before riding the bicycle, check the following items. If any problems are found with the following items, contact the place of purchase or a distributor.
• Does the drive train perform gear shifting smoothly?
• Are the components fixed securely and free from damage?
• Are the components securely installed to the frame/ handlebar/stem, etc.?
• Do any abnormal noises occur while riding?
• Is there sufficient charge remaining in the battery?
4
FCC compliance information
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
5
Booklet Structure
SHIMANO STEPS user's manuals are split among several booklets, as described below.
Be sure to read these user's manuals thoroughly before use, and follow them for correct use. Store the user's manuals so that they can be referenced at any time.
The latest user's manuals are available on our website (https://si.shimano.com).
•
SHIMANO STEPS user's manual
This is the basic user's manual for SHIMANO STEPS. It contains the following content.
- SHIMANO STEPS quick guide
- How to operate assist bicycles that use flat handlebars, such as city, trekking, or MTB type bicycles
- Troubleshooting
•
SHIMANO STEPS user's manual for drop handlebar bicycles (separate booklet)
This booklet describes how to operate assist bicycles that use a drop handlebar and are controlled using a dual control lever. This should be read along with the SHIMANO STEPS user's manual.
•
SHIMANO STEPS special battery and parts user's manual
It contains the following content.
- How to charge and handle the SHIMANO STEPS special battery
- How to attach and remove the SHIMANO STEPS special battery to the bicycle
- How to use the satellite system on/off switch and satellite charging port
- How to read the battery LEDs when charging or during an error, and how to handle errors
•
Cycle computer user's manual (this document)
It contains the following content.
- Basic operations of the cycle computer and how to configure settings
- Wireless communication method
- How to handle errors/warnings and cycle computer troubleshooting
•
Switch unit user's manual
This is the assist switch and shifting switch user's manual. Describes switch unit operations.
6
Names of parts
This product is operated with the function button on the main body and the switch unit included in the assist bicycle.
3-switch type switch unit (left)
3-switch type switch unit (right)
SC-E6100
X
A
Y
Function button
Light button
Power button
2-switch type switch unit (left)
X
X
Y
Y
MTB type switch unit (left)
2-switch type switch unit (right)
X
Y
MTB type switch unit (right)
X
Y
X
A
Y
Y X
The operation for each button/switch is indicated below.
Cycle computer
Function
Button*1
When riding:
Switching traveling data display
When setting:
Switch screen or confirm setting changes
Power button
Main power ON/OFF
Light button
Light ON/OFF
X Y
*1
The operation performed when the button is held down differs according to whether a switch unit with an assist function assigned is connected.
• If a switch unit with an assist function assigned is connected: Display setting menu screen
• If a switch unit with an assist function assigned is not connected: Change assist mode
7
Switch-X
Switch-Y
Switch-A
Switch unit (left)
(default: for assist)
When riding:
Increase assistance
When setting:
Move cursor or change setting
When riding:
Decrease assistance
When setting:
Move cursor or change setting
When riding:
Switching traveling data display
When setting:
Switch screen or confirm setting changes
Switch-X
Switch-Y
Switch unit (right)
(default: electronic gear shifting)
When riding:
Shifting up
When riding:
Shifting down
Switch-A*1
When riding:
Switch between automatic and manual gear shifting
*1
Only when the assist bicycle supports automatic gear shifting.
• This manual uses default settings for all explanations regarding the function assignment of the switch unit. The functions assigned to switches can be changed from those described here, by connecting to E-TUBE PROJECT. Please contact your place of purchase for details.
• The switch layout may differ according to the switch unit. Refer to the switch unit user's manual for details.
Notation method for operations
Subsequent operations using the main body button and switch unit of this product are indicated using the following notation.
Notation Operation
<F>
Indicates an operation for pressing the function button.
<
↑
>
Indicates an operation for pressing the switch-X of the assist switch.
<
↓
>
[Clock]
(Example) Time setting
<A>
Indicates an operation for pressing the switch-Y of the assist switch.
Items displayed on the cycle computer screen are enclosed in square brackets in this manual. When this notation is used in a procedure, it indicates an operation for selecting a display on the screen and pressing the function button or the switch-A of the assist switch to switch the screen or confirm the setting.
Indicates an operation for pressing the switch-A of the assist switch.
• Operations indicated with <F> may be performed with <A> instead.
8
Installing and removing the cycle computer
This product can be easily removed from the bicycle.
• If it cannot be easily removed with the procedure indicated here, or if you want to secure the product to prevent it from being easily removed, please contact your place of purchase.
Removing
1.
Slide out the cycle computer.
• Slide the cycle computer to the front while pushing the bracket lever down to remove it.
NOTICE
• This product does not operate when removed from the bicycle.
The power turns OFF immediately, even if the power button is pressed.
Lever
Installing
1.
Slide the cycle computer onto the bracket.
2.
Insert the cycle computer securely until it clicks into place.
NOTICE
If the cycle computer is not correctly installed, the assist function will not operate normally.
Bracket
9
Basic operation
Turning the power ON/OFF
When the power is turned ON with this product installed to the bicycle, all components connected to the drive unit are also turned ON (such as assist driving, the electronic gear shifting mechanism, and the lights).
NOTICE
• Before turning the power ON, please refer the SHIMANO STEPS special battery and parts user's manual to check the following.
- The battery is firmly attached to the battery mount (refer to the “SHIMANO STEPS Special Battery and Parts User's Manual”).
- The cycle computer is firmly attached to the bracket.
• The power cannot be turned ON while charging.
• Do not step on the pedal when turning the power ON/OFF. Doing so may cause a system error.
• The built-in battery of this product is charged while the system is running. If the charge is insufficient because of long-term storage, etc., charge the built-in battery using one of the methods below. It takes a maximum of 2 hours to charge the built-in battery.
- Charge the built-in battery while the (main) battery is mounted on the bicycle. (Only when the component with the charging port is the
BM-E6000 / BM-E6010 / EW-CP100. Refer to the "SHIMANO STEPS Special Battery and Parts User's Manual.")
* When the (main) battery is fully charged, charging of the built-in battery also stops automatically.
- The power can be turned ON using the power button of the (main) battery. (Refer to the "SHIMANO STEPS User's Manual" and
"SHIMANO STEPS Special Battery and Parts User's Manual".)
* The power automatically turns OFF if the bicycle is stopped for 10 minutes. When charging for more than 10 minutes, operate any switch on the bicycle or turn the crank to keep the system running.
- This product can be charged by connecting to the PC version of E-TUBE PROJECT. Make a request to the place of purchase.
1.
Hold the power button down until the screen turns on.
Power button
•
If the bicycle is left unused for 10 minutes after turning the power ON, the power automatically turns OFF (auto power OFF function).
When the main power is turned ON, a screen similar to that shown below is displayed, and then switches to the main screen.
Normal startup Battery level too low
10
* The level of the cycle computer's built-in battery is too low.
Viewing the screen
The items displayed on the main screen differ according to the assist bicycle.
Main screen
(J) (K)
(I)
(H)
(G)
(F)
(E)
(A)
(B)
(C)
Battery level indicator
(Refer to "Battery level indicator")
Maintenance alert
Indicates that maintenance is required. Contact your place of purchase or a distributor if this icon is displayed.
Gear position display *1
Current gear position
Start mode gear position *2
Shifting advice *3
This notifies you of the recommended timing at which to shift based on the bicycle riding conditions.
(A)
(B)
(C)
(D)
(E)
(F)
(G)
Gear shifting mode *4 *5
[Auto]: Displayed for the auto gear shifting mode.
[Manual]: Displayed for the manual gear shifting mode.
Assist gauge
Displays the assist strength. A mode that provides stronger assistance the longer the length of the displayed gauge.
Current assist mode *5
The assist modes that can be selected differ according to the assist bicycle.
(H)
Current speed
(I)
Current time
(D)
Travel data display
The traveling data that can be displayed differs according to the assist bicycle. (Refer to
"Switching the traveling data display".)
(J)
(K)
Light icon
Indicates that the light connected to the drive unit is lit.
Bluetooth
®
LE icon
Displayed when an external device is connected over Bluetooth
®
*1
Only displayed for electronic gear shifting.
*2
11
*3
*4
For bicycles that cannot switch the gear shifting mode, the display is fixed to [Auto] or [Manual].
*5
Refer to the SHIMANO STEPS user's manual.
Battery level indicator
The battery level is shown as an icon.
Display Battery level
100 - 81%
80 - 61%
60 - 41%
40 - 21%
20 - 1% *
0%
* The battery level indicator will flash when the battery level is low.
• The cycle computer uses zero to indicate a battery level where assistance cannot be performed. With the SHIMANO STEPS system, the light can still be lit up for a while when assist stops due to a low battery. Therefore, the above-mentioned battery level may differ from that which can be checked on the battery.
12
Turning the light ON/OFF
If a light is connected to the drive unit, this product can be used to operate the light.
1.
Press the light button.
• Lights are turned on.
• To turning off the lights, push the button again.
* When the battery powered light is not connected and
[Backlight] is set to [MANUAL], pressing the light button turns the cycle computer’s backlight on and off.
When the light is turned on
Light button
When the light is turned off
• The light power is linked with the main power. The light cannot be turned ON when the main power is OFF.
13
Switching the traveling data display
The traveling data that can be displayed differs according to the assist bicycle.
1.
On the main screen: <F>
Travel data display
The traveling data switches in the following order each time <F> is pressed.
Display item
[DST]
[ODO]
[RANGE]
[RANGE]
[TIME]
Traveling distance
Cumulative distance
Traveling range *1
Traveling range for each assist mode *1 *2 *3
Traveling time *3
[AVG]
[MAX]
Average speed *3
Maximum speed *3
[CADENCE] Crank rotation speed *3*4
Explanation
*1
Reference value. The value is displayed when the assist mode is set to a value other than [OFF] or [WALK]. The battery level cannot be displayed while this is being shown.
*2
It is displayed as shown in the figure. The gear position cannot be displayed while this is being shown.
*3
Whether to show this or not can be set with E-TUBE PROJECT.
*4
It is displayed when the assist mode is set to a value other than [OFF] or [WALK] with electronic gear shifting.
• If the traveling data display that can be displayed is repeatedly switched, it will eventually switch back to displaying [DST].
14
Resetting the traveling distance
The traveling distance is reset from the main screen. When the traveling distance is reset, [TIME] (traveling time), [AVG]
(average speed), and [MAX] (maximum speed) will also be reset.
1.
On the main screen: <F> (switches the traveling data display to [DST])
2.
<F> (continue to hold until the number displayed for [DST] flashes)
3.
When the number displayed for [DST] flashes: <F>
The traveling data is reset.
• If nothing is done for five seconds after the number for [DST] begins flashing, it will stop flashing and the screen will return to the main screen.
15
Setting menu
The items that can be set differ according to the assist bicycle. If assist switch is not connected, the setting menu cannot be displayed.
Switching to the setting menu
To display the setting menu, perform the following operation when the traveling data display is something other than [DST].
1.
Stop the bicycle
⇒
<F> (continue to hold until the screen switches)
Main screen Setting menu screen
• You can also use the following methods to display the setting menu.
- Stop the bicycle
⇒
<A> (continue to hold until the screen switches)
- Stop the bicycle
⇒
<
↑
> + <
↓
> (continue to hold until the screen switches)
Returning to the main screen from the setting menu screen [Exit]
Closes the setting menu and returns to the main screen.
1.
Setting menu screen
⇒
[Exit]
16
Setting the time [Clock]
1.
Setting menu screen
⇒
[Clock]
⇒
<
↑
> or <
↓
> to change the "Hour" number
⇒
<F>
The cursor moves to the "Minute" number.
2.
<
↑
> and <
↓
> to change the "Minute" number
⇒
<F>
The display will automatically return to the setting menu screen.
• Continue to hold <
↑
> or <
↓
> to change the number quickly.
Turning the operation sound ON/OFF [Beep]
Set whether to emit the operation sound.
1.
Setting menu screen
⇒
[Beep]
⇒
[ON] / [OFF]
The display will automatically return to the setting menu screen.
• The beep sound for operation mistakes and system errors cannot be turned OFF.
17
Setting the display
Backlight setting [Backlight]
Configurable items
[ON]
[OFF]
[MANUAL]
Details
Always turned on
Always turned off
The backlight will turn ON/OFF when the light connected to the drive unit is turned ON/OFF. If no light is connected, the backlight can be turned ON/OFF by operating the cycle computer's light button.
1.
Setting menu screen
⇒
[Backlight]
⇒
[ON] / [OFF] / [MANUAL]
The display will automatically return to the setting menu screen.
Setting the screen brightness [Brightness]
1.
Setting menu screen
⇒
[Brightness]
⇒
<
↑
> or <
↓
> to adjust the brightness
⇒
<F>
The display will automatically return to the setting menu screen.
Switching the font color [Font color]
1.
Setting menu screen
⇒
[Font color]
⇒
[White] / [Black]
The display will automatically return to the setting menu screen.
Switching the display language [Language]
1.
Setting menu screen
⇒
[Language]
⇒
select the display language
⇒
<F>
The display will automatically return to the setting menu screen.
18
Changing the unit of the speed and distance [Unit]
Select the unit for displaying the speed and distance.
1.
Setting menu screen
⇒
[Unit]
⇒
[km] / [mile]
The display will automatically return to the setting menu screen.
Matching the displayed speed with another device [Display speed]
You can adjust the displayed value when there is a difference between the speed displayed on this product and the speed indicator of another device.
Setting items
Increase value
Decrease value
Increases the displayed speed value.
Explanation
Decreases the displayed speed value.
1.
Setting menu screen
⇒
[Display speed]
⇒
<
↑
> or <
↓
> to adjust the value
⇒
<F>
The display will automatically return to the setting menu screen.
• This setting only changes the displayed value. It does not change the power assist function.
Resetting the settings [Clear]
Resets the traveling distance and settings. When the traveling distance is reset, [TIME] (traveling time), [AVG] (average speed), and [MAX] (maximum speed) will also be reset.
Configurable items
[Exit]
[DST]
[Default]
*
Return to setting menu.
Reset the traveling distance.
Resets the settings.
Details
19
* When the settings are reset, the following will be reset to their default settings.
• [Backlight]: [ON] • [Beep]: [ON] • [Unit]: [km]
• [Language]: [English] • [Brightness]: [3] • [Font color]: [White]
1.
Setting menu screen
⇒
[Clear]
⇒
[DST] / [Default]
The display will automatically return to the setting menu screen.
20
Setting the assist bicycle function
Setting the gear position when starting from a stop [Start mode]
Automatically shifts to the set gear position when the bicycle starts from a stop.
Setting items
[OFF]
[1], [2],...*1
Do not set the start mode.
Select the gear position.
Explanation
*1
A gear position up to the maximum gear position of the shifting unit installed to the assist bicycle can be set.
1.
Setting menu screen
⇒
[Start mode]
⇒
<
↑
> or <
↓
> to select the gear position
⇒
<F>
The display will automatically return to the setting menu.
Dynamically changing the riding comfort [Assist customize]
The riding comfort of the assist bicycle differs greatly according to the maximum torque of the drive unit and how much assistance is provided for pedaling. This product has multiple recommended settings registered that can be switched according to your preference. Details of the settings can be checked with E-TUBE PROJECT and the settings can be customized. Refer to the help manual for E-TUBE PROJECT for details.
Setting items
[Profile 1]
[Profile 2]
Explanation
Changes to the riding comfort registered in [Profile 1].
Changes to the riding comfort registered in [Profile 2].
1.
Setting menu screen
⇒
[Assist customize]
⇒
[Profile 1] / [Profile 2]
NOTICE
Depending on the setting, battery consumption may increase and the assisted traveling range may greatly decrease.
• The settings may differ according to the assist bicycle. Refer to the manual for the assist bicycle.
21
Indicating the optimal gear shifting timing via an icon [Shifting advice]
Performing gear shifting in addition to changing the assist mode enables more comfortable driving. Actively performing gear shifting without relying on only changing the assist mode can also reduce battery consumption. The gear shifting advice function uses an icon to notify you of the recommended timing at which to perform gear shifting, based on the bicycle riding conditions. The display timing can be adjusted in [Shift timing].
Configurable items
[ON]
[OFF]
Details
Enables the gear shifting advice function, which displays an icon to notify the user of the recommended timing for gear shifting during manual gear shifting.
Disable the shifting advice function
1.
Setting menu screen
⇒
[Shifting advice]
⇒
[ON] / [OFF]
The display will automatically return to the setting menu screen.
Adjusting auto gear shifting [Shift timing]
Adjusts the gear shifting timing during automatic gear shifting.
Also sets the timing at which gear shifting advice is displayed.
Setting items
Increase value
Decrease value
Explanation
Increase the value when pedaling feels too heavy.
Decrease the value when pedaling feels too light.
1.
Setting menu screen
⇒
[Shift timing]
⇒
<
↑
> or <
↓
> to adjust the value
⇒
<F>
The display will automatically return to the setting menu.
22
Wireless connection
This product has a wireless communication function.
2.4 GHz digital wireless systems
2.4 GHz frequency digital wireless technology is the same thing as a wireless LAN. In rare instances, strong electromagnetic waves or electromagnetic interference due to the following locations or devices may impact communication.
• TVs, PCs, radios, motors/engines, or inside vehicles or trains
• Near railroad crossings and tracks, television transmitter stations, and radar stations
• Other wireless computers or digital control lights
ANT connection
All the information displayed on the main screen can be sent to an external device that supports ANT connections.
Connection method
When the main power is turned ON for SHIMANO STEPS, communication can be received at any time. Refer to the manual of the external device, switch the external device to connection mode, and then connect it.
Bluetooth ® LE connection
All the information displayed on the main screen can be sent to an external device that supports Bluetooth ® LE connections.
E-TUBE PROJECT for smartphones/tablets may be used if a Bluetooth ® LE connection is established with a smartphone/tablet.
E-TUBE RIDE can be used to check traveling data on a smartphone connected over Bluetooth
®
LE.
Connection method
Communication can only be received under the following conditions. Refer to the manual of the external device, switch the external device to connection mode, and then connect it.
• Within 30 seconds of the main power for SHIMANO STEPS turning ON
• Within 30 seconds of operating any button/switch other than the SHIMANO STEPS power switch
Wireless system specifications
Model name
Frequency band
Maximum high-frequency output
Firmware version
SC-E6100
2,402 - 2,480 MHz
+4 dBm
4.0.0 or later
E-TUBE PROJECT
E-TUBE PROJECT is needed to change the setting of the SHIMANO STEPS and to update firmware.
Download E-TUBE PROJECT from our support website (https://e-tubeproject.shimano.com).
For information on how to install E-TUBE PROJECT, check the support website.
NOTICE
Do not connect to a device while the battery is being charged.
• Firmware is subject to change without notice.
23
Items configurable in E-TUBE PROJECT
The items that can be set differ according to the assist bicycle. Refer to the help manual for E-TUBE PROJECT for details.
• The functions assigned to each operation switch can be changed.
• The settings that can be configured from this product can also be configured from E-TUBE PROJECT.
•
24
Troubleshooting
Recovering from the RD protection function [RD protection reset]
In order to protect the system from falls etc., the RD Protection function will operate when the rear derailleur is subjected to a strong impact. The connection between the motor and the link will be momentarily severed so that the rear derailleur can no longer operate.
When RD Protection Reset is run, it will restore the connection between the motor and the link, and recover the rear derailleur from RD Protection.
• This function is enabled for electronic gear shifting rear derailleur models only.
1.
Setting menu
⇒
[RD protection reset]
⇒
[OK]
An illustration of a crankset is displayed on the screen.
2.
Turn the crank clockwise with the rear wheel lifted up.
The rear derailleur moves, and the connection between the motor and link is restored.
Gear shifting adjustment with the electronic gear shifting unit [Adjust]
If gear shifting feels abnormal, contact the place of purchase.
25
Warning / error indication
The PC version of E-TUBE PROJECT classifies errors and warnings into more detailed categories according to the cause. For this reason, the error and warning codes that are displayed in the PC version of E-TUBE PROJECT may differ from those displayed on personal cycle computers, E-TUBE RIDE, or E-TUBE PROJECT for smartphones / tablets.
Warning indication
If the situation is resolved, this indication will disappear. If the situation does not improve, contact the place of purchase.
Code*1
W101
(W011)
W103
(W013)
W104
W105
Indication conditions
Traveling speed not detected.
Initialization did not complete normally for the torque sensor.
Assistance will be lower than normal.
Press the battery power button without stepping on the pedal to turn the power ON again.
Current leakage detected in the system and power turned OFF.
Unexpected power disconnection detected.
-
Operational restrictions being displayed
Remedy
The maximum speed up to which assist is provided will be lower than normal.
Have your place of purchase perform the following.
• Check to see if the speed sensor is installed in the correct position.
• Check to see if the magnet on the disc brake rotor is attached. (Refer to the "Disc brake" section in
"General operations" for how to install the removed magnet.)
Assist will not be provided when riding.
Have your place of purchase perform the following.
Remove the components other than the drive unit one by one, then turn the power back ON.
• If the component with a problem has not been removed, the power turns OFF during startup.
• If the component with a problem has been removed, the power turns ON and W104 remains displayed.
Refer to the "SHIMANO STEPS User's manual" and turn the power OFF and then ON again.
If W105 is displayed frequently, have your place of purchase perform the following.
• Check to see if the battery holder rattles or if the power cord is disconnected.
26
Code*1
W200
(W020)
W302
(W032)
Indication conditions
Operational restrictions being displayed
Remedy
If the temperature exceeds the guaranteed operating range, the battery output stops.
Shifting unit different from system configuration is installed.
No system functions will start.
Unable to perform gear shifting.
If the temperature is higher than the temperature at which discharging is possible, leave the battery in a cool location with no direct sunlight until the internal temperature of the battery has decreased sufficiently. If the temperature is lower than the temperature at which discharging is possible, leave the battery indoors until the internal temperature has increased to an appropriate temperature.
Have your place of purchase perform the following.
Replace with the shifting unit configured in the system.
Or check the current system status with E-TUBE
PROJECT.
*1 The instruction in the parentheses is displayed according to the drive unit connected.
27
Error indication
If an error message is displayed on the entire screen, refer to the SHIMANO STEPS special battery and parts user's manual and follow one of the procedures below to reset the display.
• Press the battery power button to turn the power OFF.
•
Remove the battery from the battery mount.
NOTICE
• If the situation does not improve even after turning the power back ON, consult with the place of purchase or a distributor.
Code*1
E010
E020
E021
E022
E023
Indication conditions
Operational restrictions being displayed
Remedy
System error detected.
Communication error between the battery and drive unit detected.
Battery connected to drive unit conforms with system standards but is not supported.
Battery connected to drive unit does not conform with system standards.
Electrical abnormality in battery detected.
Assist will not be provided when riding.
Assist will not be provided when riding.
Assist will not be provided when riding.
No system functions will start.
No system functions will start.
Refer to the "SHIMANO STEPS User's manual" to turn the power OFF and then ON again. If the situation does not improve, contact the place of purchase or a distributor.
Have your place of purchase perform the following.
• Check to see if the cable between the drive unit and battery is connected correctly.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check the power cord for abnormalities. If the error persists, contact your distributor.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check the power cord for abnormalities. If the error persists, contact your distributor.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check the power cord for abnormalities. If the error persists, contact your distributor.
28
Code*1
E024
Indication conditions
Operational restrictions being displayed
Remedy
Battery overcurrent protection occurred.
No system functions will start.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check the power cord for abnormalities. If the error persists, contact your distributor.
E025
E030
E033
E034
(E013)
E035
E043
E050
(E014)
Battery does not recognize the drive unit.
No system functions will start.
Have your place of purchase perform the following.
• Connect a genuine SHIMANO battery. Also check the power cord for abnormalities. If the error persists, contact your distributor.
Shifting unit different from system configuration is installed.
Assist will not be provided when riding.
Have your place of purchase perform the following.
Replace with the shifting unit configured in the system. Or check the current system status with
E-TUBE PROJECT.
Current firmware is not supported by this system.
Assist will not be provided when riding.
Have your place of purchase perform the following.
• Connect to E-TUBE PROJECT to update the firmware on all the assist bicycle units to the latest version.
Abnormality detected in drive unit’s firmware.
Assist will not be provided when riding.
Contact your place of purchase or a distributor. The firmware needs to be restored.
Configuration error.
Assist will not be provided when riding.
Have your place of purchase perform the following.
Connect to E-TUBE PROJECT to check the configuration.
Abnormality detected in firmware on this product. Part of the firmware may be corrupted.
Assist will not be provided when riding.
Contact your place of purchase or a distributor. The firmware needs to be restored.
Speed sensor may be installed in an incorrect position.
Assist will not be provided when riding.
Have your place of purchase perform the following.
Check to see if the speed sensor is installed in the correct position. If not installed in the correct position, install it in the correct position and ride the bicycle for a while. Doing so should fix the error. If the error persists, contact your distributor.
*1 The instruction in the parentheses is displayed according to the drive unit connected.
29
When a problem occurs
Symptoms
The cycle computer does not start when the power button is pressed.
The system does not start when the (main) battery power button is pressed.
The gear position is not displayed.
I want to turn the operation sound OFF.
Cannot start the setting menu while riding.
Possible cause
Is the battery charging?
The level of the cycle computer's built-in battery is too low.
The (main) battery level may be too low.
Is the power ON?
Is the battery charging?
Is the connector of the electric wire installed correctly?
Remedy
When charging with the battery installed to a bicycle, you cannot start the system.
The screen continues to display the
SHIMANO STEPS logo.
Refer to the “SHIMANO STEPS Special
Battery and Parts User's Manual” to start the system using the (main) battery power button or satellite system on/off switch. For information on charging the built-in battery of the cycle computer, refer to
Refer the SHIMANO STEPS special battery and parts user's manual to charge the battery, and then turn the power ON again.
Refer the SHIMANO STEPS special battery and parts user's manual to turn the power
ON.
When charging with the battery installed to a bicycle, you cannot start the system.
The screen continues to display the
SHIMANO STEPS logo.
Check whether the connector of the electric wire is disconnected. If you are not sure, contact the place of purchase.
A product that the system cannot identify may be connected.
Contact the place of purchase.
The gear position is only displayed when the electronic gear shifting unit is installed.
Check whether the connector of the electric wire is disconnected. If you are not sure, contact the place of purchase.
Refer to "Turning the operation sound ON/
The product is designed to prevent the setting menu from being started while riding is detected. This is normal.
Configure the settings after stopping.
A switch operation cannot be performed and two beeps are heard.
Operation of the switch you pressed is prohibited.
This is not a malfunction.
Three beeps are heard.
An error or warning has occurred.
A warning or error is displayed on the cycle
computer. Refer to "Warning indication"
The gear position set in the start mode is not set when the bicycle is stopped.
You may have pressed the pedal too strongly.
Pressing the pedal gently makes it easier to shift gears.
30
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222
3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice. (English)
© Apr. 2020 by SHIMANO INC. ITP
डाउनलोड
विज्ञापन