en

Brief and handy: everything your dishwasher needs …

Before using for the first time, read the Installation instructions and Operating instructions!

2

Adjusting the water softening system*

1

Ask your water supply company what the water hardness is and enter...

* only before the first wash or if the water hardness has been changed

Water hardness value

°Clarke

0-8

9-10

11-12

13-15

16-20

21-26

27-38

39-44

Hardness range soft soft medium medium medium hard hard hard mmol/l

0 -1.1

1.2-1.4

1.5-1.8

1.9-2.1

2.2-2.9

3.0-3.7

3.8-5.4

5.5-6.2

Filling the salt dispenser Dissolves limescale (not necessary for set value 0!) ...

Unscrew cover.

Factory setting

:

:

• ‹ƒ

:

:

• ‹…

:

:

• ‹‡

A

Start

B

Fill the salt dispenser with water before the first wash only.

Quickly sorted ...

How to adjust

– Switch on ON/OFF switch.

– Press and hold down the START button A .

– Rotate programme selector B until H:0.

is indicated on the digital display.

– Release button.

The factory set value H:04 is lit on the digital display.

– Rotate programme selector B until the required value is indicated

on the digital display.

– Press START button A .

The set value is saved.

Add special salt

(never add detergent!).

Screw on the cover.

Wash immediately.

5

4

Adding detergent

Switching on the appliance

6

3

Adding rinse aid

Select programme

Start programme

Here we go...

Start

8

9

Switch off the appliance

Everything o.k....

7

$

Spick and span ...

2

Press mark 1, lift up cover 2.

Fill in rinse aid .

1 %

A lot of dirt, a lot of detergent ...

If required, open the cover

(press button).

7

Quick, economical or intensive ...

Attention:

Combination products are not suitable for all programmes, follow manufacturer’s instructions.

Overview of programmes

The max. possible number of programmes is illustrated in this overview.

The corresponding programmes for your appliance can be found on the fascia.

The programme data has been measured in the laboratory according to European standard EN 50242.

Deviations are possible in practice.

Duration: hs : mins

Energy consumption in kWh

Water consumption in litres

With Aquasensor

50 ml

25 ml

15 ml

Intensive

70°

± ²

2:00

0,90

9

7,5

Additional options**

Ÿ

Express Wash

... is obtained by increased energy consumption at a constant cleaning performance.

·

Hygiene

... the temperature is increased during the final rinse process.

This increases the hygiene status.

Flexibility…

¿

Extra drying

... improves the drying result by increased temperature in the final rinse.

(Please take care with delicate dishes.)

** depending on model

Pour detergent into the dry detergent dispenser only.

Auto

45°–65°

Eco

50°

Á

á

1:30-2:30

à

2:40

0,55 - 0,85

-

6 - 9

0,63

7

-

Gentle

40°

é ê

1:15

0,45

7

6

Screw on the cover.

CLICK!

Slide cover shut, press.

PLOP!

Quick

45°

ñ ð

0:29

0,45

6

-

Prerinse

ù

0:15

0,05

3

-

ø

Maintenance and care

Filters

... check, if required, clean.

Rotate filter cylinder, remove filter system...

For perfect rinsing results ...

rinse under running water ...

insert ...

Screw on filter system

NOTE

MARK!

Cleaning waste water pump

– Pull out the mains plug.

– Remove filters and scoop out water.

– Loosen screws on the pump cover

(TorxT20).

– Pull off cover.

– Check area around the fan impeller

for foreign objects.

– Insert cover and screw tight.

– Insert filters.

Spray arm

...remove blockages/ deposits.

pull lower arm upwards ...

clean spray nozzles under running water

(if required use toothpicks) ...

insert spray arm ...

Rectifying minor faults yourself ...

Fault

Display “ 6 ” is lit

Display “ E:24 ” and “ 6 ” are lit

Display “ E:25 ” and “ 6 ” are lit

Other fault display

“ E:XX ” is lit

Residual water in the appliance

Possible causes

Supply fitting jammed or calcified

Waste water hose is blocked or kinked

Cover not attached to waste water pump

Waste water pump blocked

Appliance has technical defect

The programme has not yet ended

... as it is worth doing it yourself!

Remedial action

Open supply fitting.

1. Unscrew water connection.

2. Clean filter in the water connection.

3. Flow rate must be min. 10l/min., when water supply is open.

If the flow rate is less, replace the supply fitting.

Install supply hose without kinks.

Install waste water hose without kinks.

Attach cover (see above).

Clean waste-water pump (see above).

Call factory customer service (state fault display).

Unplug appliance.

Close the appliance and switch it on or terminate the programme (see Terminating the programme).

Rust on the cutlery Cutlery not rust-resistant

Hard knife blades are more susceptible

Extraneous rust

Terminating the programme ...

While the programme is running, press the START button for approx. 3 sec. (Reset).

The numerical display indicates “0:01”; approx. 1 minute after the programme ends,

“0:00” is indicated.

Use dishwasher-proof cutlery.

Never wash rusting parts in the appliance.

Switch off the appliance.

Fault

Utensils are not clean

Sand or gritty residue on the utensils

Possible causes

Utensils are situated close together or one above the other

Too little detergent

Unsuitable programme selected

Spray arm nozzles blocked

Filters dirty, not seated firmly

Spray arms blocked

More information can be found in the operating instructions

Remedial action

Separate the utensils, prevent contact points.

Follow manufacturer’s instructions (detergent).

Select a more intensive programme.

Clean the spray arms (see above).

Clean the filters (see above).

Arrange the utensils so that the spray arms can rotate freely.

Stains and streaks Rinse aid dosage too high/too low

Utensils not dry

Milky deposits on the utensils

(can be removed)

Milky deposits, glasses cloudy/tarnished

(cannot be removed)

Plastic/utensils discoloured

Rinse aid

The combined detergent used has a poor drying performance

Appliance setting

Water softening system incorrectly set

No salt

Glasses not dishwasher-proof

Too little detergent

Discoloration caused by food colourings

(tomato sauce)

Loading the dishwasher correctly ...

Streaks: reduce dosage.

Water or limescale stains: increase dosage.

Increase dosage.

Change the product.

Use rinse aid.

Activate intensive drying (depending on model).

Correctly set water softening system.

Refill with special salt.

Use dishwasher- proof glasses.

Use a detergent suitable for glasses.

Follow manufacturer’s instructions (detergent).

Discoloration is harmless; subsequent rinse cycles will cause it to fade.

Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove large remnants of jam, milk products and food according to the operating instructions and check that the spray arms can rotate freely.