advertisement
en Brief and handy: everything your dishwasher needs ...
Before using for the first time, read the operating instructions!
Filling the salt dispenser
Adjusting the water softening system *
Ask your water supply company what the
water hardness is and
enter...
Water hardness value _ dH
Hardness range soft mmol/l Set value
B
* only before the
first wash or if the water hardness has been changed soft medium medium medium hard hard hard
Dissolves limescale (not necessary for set value 0 !) ...
Unscrew cover.
Fill the salt dispenser with water before the first wash only.
Adding rinse aid
Spick and span ...
Press mark 1, lift up cover 2.
A
C
Quickly sorted ...
How to adjust the water softening system
– Switch on ON/OFF switch
– Hold down programme button A and press START button until H:0... is indicated on the digital display.
– Release both buttons.
The LED for button A flashes and the factory set value of H:04 is indicated on the digital display
– Press programme button C.
Each time the button is pressed the set value increases by one setting; when the value reaches H:07, the display jumps back to H:00 (off).
– Press START button. The chosen setting has now been stored.
Add salt
(never add detergent!).
Screw on the cover. Wash immediately.
Refill if rinse-aid refill indicator is lit!
Adding
rinse aid.
Screw on the cover.
CLICK!
Adding detergent
Switching on the appliance
Select programme
Start programme
Here we go...
Switch off the appliance
Everything o.k...
A lot of dirt, a lot of detergent ...
If required, open the cover (press button).
Attention
Combination products are not suitable for all programmes, follow manufacturer’s instructions.
Adding
detergent.
Quick, economical or intensive ...
Overview of programmes
Intensive
70 _
Auto
45 _ /65 _
Eco
50 _
Gentle
40 _
The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia.
The programme data has been measured in the laboratory according to European standard EN 50242.
Deviations are possible in practice.
* half normal load
Additional options **
Express Wash
(VarioSpeed)
... is obtained by increased energy consumption at a constant cleaning and drying performance.
Half load
... for a few items, saves water, energy and time
Duration: hs/mins
Energy Consumption: kWh
Water consumption in litres
With Aquasensor
2:15
1,50
15
12
Flexibility ...
IntensiveZone
... perfect for a mixed load. Washing pressure and washing temperature are increased slightly.
** depending on model
1:25-2:30
1,00-1,60
–
9-19
2:20
1,05
12
–
Hygiene
... The temperature is increased during the rinsing process. This increases the hygiene status.
1:10
0,80
13
10
Quick
45 _
Prerinse
0:29 *
0,80
10
–
Slide cover shut, press.
PLOP!
0:15
0,05
4
–
Extra drying
... improves the drying result by increased temperature in the final rinse (Please take care with delicate dishes)
Maintenance and care
Filters ...
check, if required clean
Spray arms ...
Remove blockages/deposits
Rotate filter cylinder, remove filter system ...
pull lower arm upwards ...
Rectifying minor faults yourself ...
Fault Possible causes
Display “ ” display is lit Supply fitting jammed or calcified
Display “E:24” and “ ” is lit
Display “E:25” and “ ” is lit
Other fault display “E:XX” is lit
Waste water hose is blocked or kinked
Cover not attached to waste water pump
Waste water pump blocked
Appliance has technical defect
Residual water in the appliance
The programme has not yet ended
Rust on the cutlery
Cutlery not rust-resistant. Hard knife blades are more susceptible
Extraneous rust
Terminating the programme ...
While the programme is running, press the START button for approx. 3 sec. (Reset).
The numerical display indicates “0:01” approx. 1 minute after the programme ends,
0:00 is indicated
For perfect rinsing results ...
rinse under running water ...
insert ...
Screw on filter system NOTE
MARK!
Cleaning waste water pump
– Pull out the mains plug
– Remove filters and scoop out water
– Lever off cover (––>A)
– Check area around the fan impeller for foreign objects
– Click cover shut (––>B)
– Insert filters unscrew upper arm ...
... as it is worth doing it yourself!
Remedial action
Open supply fitting.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10 l/min. when water supply is open. If the flow rate is less, replace the supply fitting.
Install supply hose without kinks.
Install waste water hose without kinks.
Attach cover (see above).
Clean waste-water pump (see above).
Call factory customer service
(state fault display).
Unplug appliance.
Close and switch on the appliance or terminate the programme
(see Terminating the programme).
Use dishwasher-proof cutlery.
Never wash rusting parts in the appliance.
Switching off the appliance clean spray nozzles under running water
(if required use toothpicks) ...
insert lower arm ...
A B screw on upper arm tightly
Fault Possible causes
Utensils are not clean
Sand or gritty residue on the utensils
Utensils are situated close together or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Stains and streaks Rinse-aid dosage too high/too low
Milky deposits on the utensils (can be removed)
Milky deposits, glasses cloudy/tarnished
(cannot be removed)
Water softening system incorrectly set;
No salt
Glasses not dishwasher-proof.
Plastic/utensils discoloured
Too little detergent.
Discoloration caused by food colourings
(tomato sauce)
Remedial action
Separate the utensils, prevent contact points.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray arms can rotate freely.
Streaks: reduce dosage.
Water or limescale stains: increase dosage.
Correctly set water softening system.
Refill with salt.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
Follow manufacturer’s instructions
(detergent).
Discoloration is harmless; subsequent rinse cycles will cause it to fade.
More information can be found in the operating instructions
Loading the dishwasher correctly ...
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove large remnants of jam, milk products and food according to the operating instructions and check that the spray arms can rotate freely.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement