Eval Kit Manual
DN[Document ID]
AS5x47
Socket Board
AS5x47-TS_EK_SB ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 1
Document Feedback
AS5x47 Socket Board
Table of Contents
1
1.1
2
3
3.1
3.2
4
5
Revision History
Introduction .......................................................................................................................... 3
Kit Content ........................................................................................................................... 3
Board description ................................................................................................................. 4
AS5x47-TS_EK_SB Hardware ............................................................................................ 5
AS5x47-TS_EK_SB schematics .......................................................................................... 5
AS5x47-TS_EK_SB PCB layout .......................................................................................... 6
Ordering & Contact Information ........................................................................................... 7
Copyrights & Disclaimer ....................................................................................................... 8
Revision
1.0
Date
20.01.2015
Owner mzie
Description
Initial version ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 2
Document Feedback
AS5x47 Socket Board
1 Introduction
The AS5x47-TS_EK_SB socket board is used for quick programming of the AS5047D and AS5147 magnetic rotary position sensors without soldering due to its ZIF socket.
This board can be used in combination with the USB I&P Box or the SD4Y production programmer.
1.1 Kit Content
Figure 1: Kit content
1
Pos. Item
1 AS5x47-TS_EK_SB
Comment
Socket board ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 3
Document Feedback
AS5x47 Socket Board
2 Board description
The PCB offers 2 connecting options: The 5-pin dual-row connector on the left side for connecting to the USB I&P Box and the 10-pin dual-row connector on the right side for connecting to the SD4Y Production Programmer. Furthermore 8-pin header on top gives access to UVW, ABI and GND signals.
A ZIF Open-Top-Socket for TSSOP packages is mounted in the middle. Pin 1 of the IC is indicated by a small dot on the left bottom corner of the socket or by the label on the PCB.
All passive components needed for proper operation are included on the PCB. Only a power supply mode of 5V is possible.
Figure 2: AS5x47 socket board
Connector for
UVW, ABI signals
ZIF socket for
TSSOP
Connector for
USB I&P Box
Connector for SD4Y
Programmer ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 4
Document Feedback
AS5x47 Socket Board
3 AS5x47-TS_EK_SB Hardware
3.1 AS5x47-TS_EK_SB schematics
Figure 3: AS5x47-TS_EK_SB schematics ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 5
Document Feedback
AS5x47 Socket Board
3.2 AS5x47-TS_EK_SB PCB layout
Figure 4: AS5x47-TS_EK_SB PCB layout ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 6
Document Feedback
AS5x47 Socket Board
4 Ordering & Contact Information
Ordering Code Description
AS5x47-TS_EK_SB AS5x47 Eval Kit Socket Board
Buy our products or get free samples online at: www.ams.com/ICdirect
Technical Support is available at: www.ams.com/Technical-Support
Provide feedback about this document at: www.ams.com/Document-Feedback
For further information and requests, e-mail us at: [email protected]
For sales offices, distributors and representatives, please visit: www.ams.com/contact
Headquarters ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten
Austria, Europe
Tel: +43 (0) 3136 500 0
Website: www.ams.com
ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 7
Document Feedback
AS5x47 Socket Board
5 Copyrights & Disclaimer
Copyright ams AG, Tobelbader Strasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks
Registered. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.
Demo Kits, Evaluation Kits and Reference Designs are provided to recipient on an “as is” basis for demonstration and evaluation purposes only and are not considered to be finished end-products intended and fit for general consumer use, commercial applications and applications with special requirements such as but not limited to medical equipment or automotive applications. Demo Kits,
Evaluation Kits and Reference Designs have not been tested for compliance with electromagnetic compatibility (EMC) standards and directives, unless otherwise specified.
Demo Kits, Evaluation Kits and Reference Designs shall be used by qualified personnel only. ams AG reserves the right to change functionality and price of Demo Kits, Evaluation Kits and
Reference Designs at any time and without notice.
Any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose are disclaimed. Any claims and demands and any direct, indirect, incidental, special, exemplary or consequential damages arising from the inadequacy of the provided Demo Kits, Evaluation Kits and Reference Designs or incurred losses of any kind (e.g. loss of use, data or profits or business interruption however caused) as a consequence of their use are excluded. ams AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services. ams Eval Kit Manual, Confidential
[v1-0] 2015-Jan-20
Page 8
Document Feedback
