Owner’s Manual & Safety Instructions

Save This Manual

Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

20c

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.

Copyright

©

2016 by Harbor Freight Tools

®

. All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Safety ......................................................... 3

Setup .......................................................... 7

Setup – Before Use: ................................... 7

Operation ................................................... 10

table of contents

Maintenance .............................................. 14

Parts List and Assembly Diagram.............. 18

Warranty .................................................... 20

WarninG SyMBOLS anD DEFinitiOnS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

Addresses practices not related to personal injury.

Page 2

For technical questions, please call 1-888-866-5797.

Item 63254

iMpOrtant SaFEty inStructiOnS

WarninG - When using this product basic precautions should always be followed, including the following:

Safety Warnings

1. Read all the instructions before using the product.

2. To reduce the risk of injury, close supervision is necessary when a product is used near children.

3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.

4. Stay alert – watch what you are doing.

5. Do not operate the product when fatigued or under the influence of medication, alcohol or drugs.

6. Keep operating area clear of all persons.

7. Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

8. Follow the maintenance instructions specified in the manual.

9. This product is provided with a ground fault circuit interrupter (GFCI) built into the power cord plug. If replacement of the plug or cord is needed, use only identical replacement parts.

10. WARNING – Risk of injection or injury– do not direct discharge stream at persons.

11. Connect to individual branch circuit only.

Set up precautions

1. The work area should have adequate drainage to reduce the possibility of a fall or electric shock due to wet surfaces.

2. Wear ANSI-approved safety goggles during set up and use.

3. Only feed cold, clean water through this tool.

Pressure washer detergent may be used in the Detergent Bottle only. Do not use caustic materials, solvents, flammable materials, or detergents not designed for pressure washers.

Use of any such material can cause injury, or damage this tool or personal property.

12. WARNING – To reduce the risk of electrocution, keep all connections dry and off the ground.

Do not touch plug with wet hands.

13. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the pressure washer. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

14.

GFci prEcautiOnS

Test GFCI (Ground Fault Circuit Interrupter) before each use as follows: a. Plug GFCI into power outlet and press reset button. Indicator should turn on.

b. Press test button. Indicator should turn off.

c. Press reset button again for use.

Do not use if above test fails.

The GFCI device does not protect against electrical shock due to contact with both circuit conductors or a fault in any wiring supplying the GFCI device.

to allow GFci unit to function properly,

EXtEnSiOn cOrDS MuSt nOt BE uSED with this pressure washer.

4. Prior to starting the Pressure Washer in cold weather, check all of the parts of the unit to make sure ice has not formed. Do not store the unit anywhere that the temperature will fall near 32° F (0° C).

Item 63254

For technical questions, please call 1-888-866-5797.

Page 3

Operating precautions

1. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing pressure washers. Such preventive safety measures reduce the risk of starting the pressure washer accidentally.

2. Do not leave the equipment unattended when it is running. Turn off the equipment before leaving the work area.

3. Wear ANSI-approved safety goggles and heavyduty nonslip rubber work boots during use.

10. Do not feed already-pressurized water (such as that from another pressure washer) into this washer.

11. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.

12. Use the correct equipment for the application.

Do not modify the equipment and do not use the equipment for a purpose for which it is not intended.

4. Use only accessories that are recommended by

Harbor Freight Tools for your model. Accessories that may be suitable for one piece of equipment may become hazardous when used on another one.

5. This product must continuously run with cold water only. Never use hot water. Do not dry run this product. Dry running will cause serious damage to the seals.

13. If water is leaking out of the Pressure Washer immediately turn off the unit. Unplug the

Pressure Washer, and discharge all pressure before tightening fittings or having repair work done by a qualified technician.

14. The high pressure water flow can damage the work surface if not used properly.

Always test the spray in an open area first.

6. To avoid electrical shock, never start and run the

Pressure Washer in the rain. Never allow water to leak into the Body of the Pressure Washer.

Do not direct discharge stream at the Pressure

Washer itself or at other live electrical equipment.

7. Do not allow the GFCI Plug to become wet.

Always place the GFCI Plug in a dry location and as far away as possible from the object being sprayed.

15. Injection Hazard. The high pressure water jet produced by this tool can cut skin or cause injury to hands or eyes. Do not allow spray to strike you and do not spray toward people or animals. Do not spray the tool itself or any electrical source.

16. This Pressure Washer is intended for outdoor residential use only.

8. DO NOT use an extension cord with this product.

9. When using the Pressure Washer, always maintain a firm grip on the Spray Gun. Squeezing the

Trigger of the Spray Gun causes a kickback force.

17.

in case of an emergency during use, immediately release the trigger on the spray handle, turn the power switch off and then unplug the unit. Do not set the spray handle down without turning off the power switch.

Page 4

For technical questions, please call 1-888-866-5797.

Item 63254

Vibration Hazard:

This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the vibration effects on the user.

4. Use tools with the lowest vibration when there is a choice between different processes.

5. Include vibration-free periods each day of work.

6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.

Service precautions

Ground Fault circuit interrupter protection

This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of the power-supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection.

Servicing a Double-insulated appliance

In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated product, nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double-insulated product is marked with the words

“DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol may also be marked on the product.

SaVE tHESE inStructiOnS.

Item 63254

For technical questions, please call 1-888-866-5797.

Page 5

Symbology

Double Insulated

Intertek Testing Services

Vac

Volts Alternating Current

a

Amperes

Specifications

Electrical Rating

Working Pressure

Maximum Pressure

Maximum Flow Rate

120VAC / 60Hz / 13A

1350 PSI

1750 PSI

1.3 GPM

Maximum Water Temperature 104ºF

Maximum Inlet Water Pressure 58 PSI

High-Pressure Hose

Power Cord

20 ft

35 ft

258476

WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.

Read the manual before set-up and/or use.

WARNING marking concerning

Risk of Electric Shock.

Properly connect power cord to appropriate outlet.

WARNING marking concerning

Risk of Injection.

Do not direct spray at any person or animal.

Page 6

For technical questions, please call 1-888-866-5797.

Item 63254

Setup – Before use:

read the EntirE iMpOrtant SaFEty inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

tO prEVEnt SEriOuS inJury FrOM acciDEntaL OpEratiOn: turn the power Switch of the tool off, unplug the tool from its electrical outlet, shut off the water supply and safely discharge all residual water pressure from the unit before assembling or making any adjustments to the tool.

Functions

Handle

Spray Gun

Holder power cord Hook

High-pressure

Hose Hook nozzle

Holder

Detergent

Bottle

Holder power

Switch

Water

Outlet

Water inlet

(on back)

High-pressure

Hose

Spray

Gun

Item 63254

Detergent

Bottle

Wand nozzle nozzle tip cleaner

For technical questions, please call 1-888-866-5797.

power cord

Page 7

assembly

note:

For additional information regarding the parts listed in the following pages, refer to

Parts List and Assembly Diagram

on page 18.

Remove shipping caps from Water Inlet/Outlet.

attach Wheels

1. Push Wheels (105) in until they lock in place.

Wheel

(105)

attach Handle

1. Attach Handle (102) to front of

Pressure Washer using four Screws (90).

Handle

(102)

Screw

(90)

attach High-pressure Hose Hook

1. Slide High-Pressure Hose Hook into slot on back of Pressure Washer.

Page 8

For technical questions, please call 1-888-866-5797.

Item 63254

Slot

High-pressure

Hose Hook

connect High-pressure Hose to unit

1. Connect High-Pressure Hose (123) to front of

Pressure Washer by pushing Hose in as far as it will go, then threading coupler on tightly.

connect High-pressure Hose to Spray Gun

1. Move Hose Lock away from Hose inlet.

Insert Hose as far as it will go, then move Hose Lock toward Hose inlet.

Hose

Lock

Hose inlet

Item 63254

For technical questions, please call 1-888-866-5797.

Page 9

Operating instructions

read the EntirE iMpOrtant SaFEty inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Work piece and Work area Set up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by children or pets to prevent distraction and injury.

2. CHECK THE WATER SUPPLY. Prior to using the Pressure Washer for the first time, it is

ESSENTIAL to verify that the water supply is adequate. The Pressure Washer needs TWICE the water supply (or volume) of the listed water output

(1.3 GPM). This Pressure Washer will need about

2.6-3 GPM to operate correctly and efficiently. If the water is being supplied by a well/pump, make certain that the well/pump produces enough water to keep up with the Pressure Washer’s water demands. Water supply hoses should be heavy-duty. Water supply hoses up to 25' long must be be

5

3

/

/

8

4

" ID. Water supply hoses up to 50' long must

" ID. Do not use hoses longer than 50'. The flow rate of the water supply must never be allowed to fall below 2.6 GPM.

To determine the water supply’s flow rate: Run the water at full for one minute into a 5 gallon container, then measure the amount of water in the container.

cautiOn!

If the Pressure Washer is run with an inadequate water supply, the pump may cavitate. Cavitation causes the pump to operate loudly and will damage it.

3. USE PROPER ELECTRICAL SUPPLY. This unit uses a large amount of current, especially during start-up. Turn off power switch, then connect this unit only to a dedicated household circuit with no additional loads (running devices) connected to it. For best results, use the outlet that is nearest to the circuit breaker panel.

4. PLAN OUT THE JOB. Plan out areas to be cleaned, how many sessions will be necessary, and how long the individual sessions will need to be. Plan to clean the higher areas first. Plan a safe direction for runoff, and plan on working your way in that direction.

5. Clear the area of all objects that are not being cleaned. If any water-sensitive or delicate items cannot be moved, cover them. If detergent is to be used, cover or remove any plants or animals.

Disconnect power to and protect any nearby electrical wiring. Close windows and doors.

6. Place the Pressure Washer in a location which is protected from runoff. The location should be close enough so that the water supply hose will reach every portion of the area with some slack for movement.

7. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working.

Page 10

For technical questions, please call 1-888-866-5797.

Item 63254

tool Set up

tO prEVEnt SEriOuS inJury FrOM acciDEntaL OpEratiOn: turn the power Switch off, unplug it from its electrical outlet, and relieve all pressure before making adjustments or installing accessories.

1. MAKE SURE THE WATER INLET STRAINER AND WAND

ARE FREE OF MINERAL BUILDUP OR DEBRIS.

2. Insert Wand into end of Spray Gun, press in and twist Wand clockwise until it locks into place.

3. If using Detergent Bottle: a. Twist lid clockwise and remove. Fill Bottle with pressure washer detergent (sold separately). Replace lid.

b. Insert Detergent Bottle into end of Spray Gun, press in and twist Bottle clockwise until it locks into place.

4. Run water through water supply hose (not included) to remove any debris. Turn off water.

5. Connect water supply hose to Water Inlet on back of

Pressure Washer. Tighten securely.

6. Nozzle Adjustment:

• Twist Nozzle to left for low-impact fan spray.

• Twist Nozzle to right for high-impact narrow spray.

cautiOn!

tO prEVEnt inJury anD prOpErty DaMaGE, uSE HiGH-iMpact Spray WitH cautiOn.

Item 63254

For technical questions, please call 1-888-866-5797.

Page 11

General Operating instructions

tO prEVEnt ELEctric SHOcK anD DEatH: test Ground Fault circuit interrupter (GFci) before each use. the GFci does not protect against electrical shock due to contact with both circuit conductors or a fault in any wiring supplying in this device. Do not alter or disable the GFci. Do not use an extension cord.

This unit is intended for light to moderate cleaning. It is not intended for paint stripping or deep concrete cleaning.

1. Uncoil High-Pressure Hose completely.

Do not use pressure Washer if Hose is kinked or looped.

2. Point Spray Gun in safe direction, press Trigger to release all pressure, then release Trigger.

nOticE:

Pressure Washer will run

only

while

Trigger is pressed. When trigger is released,

Pump will turn off.

Do not leave idle for more than one minute without spraying.

3. Plug GFCI into dedicated, grounded

120V outlet, then: a. Press b. Press

rESEt tESt

button. Indicator should light up.

button. Indicator should turn off.

c. Preset

rESEt

button again. Indicator should light up, unit is ready for use.

6.

test spray an inconspicuous area

: a. Set Nozzle to low-impact fan spray.

b. Point Spray Gun at 45° angle to test area. Release Trigger Safety Lock, then press Trigger.

Be aware of kick back.

test

Button rESEt tESt indicator reset

Button

4. Turn on water supply.

5. Turn Power Switch to ON position.

note:

If the unit does not turn on or turns off suddenly, turn Power Switch to OFF position, then check and reset the GFCI.

OFF position

OFF/O

O

N

/I

On position trigger

c. Spray test area, adjusting pressure, as needed, by changing distance from surface and/or adjusting Nozzle.

d. If using detergent:

trigger

Safety Lock

• Turn off unit, remove Wand, fill detergent bottle, then attach Detergent Bottle.

• Turn on unit, then spray area with detergent according to detergent manufacturer's instructions. Scrub surface as necessary.

• Turn off unit, remove Detergent Bottle, then attach Wand.

• Set Nozzle to low-impact fan spray.

• Turn on unit, then spray area to rinse off detergent, adjusting pressure. as needed, by changing distance from surface and/or adjusting Nozzle.

e. Inspect test area for damage or discoloration.

Page 12

For technical questions, please call 1-888-866-5797.

Item 63254

cleaning Windows

a. Inspect caulking and/or glazing. Inspect trim.

DO nOt prESSurE WaSH WinDOWS iF cauLKinG/GLaZinG/triM iS nOt intact.

b. If needed, apply detergent according to manufacturer's instructions. c. Set Nozzle to low-impact fan spray.

DO nOt uSE HiGH-iMpact Spray,

FOrcE May BrEaK GLaSS.

d. Point Spray Gun at 45° angle to, and 4 feet away from, window. Spray window.

cleaning Wood

DO nOt cLEan WOOD tHat iS

HOt Or in DirEct SunLiGHt.

a. If needed, apply wood cleaning detergent according to manufacturer's instructions. For vertical surfaces, apply detergent from bottom to top. b. Scrub stained areas as needed. c. Set Nozzle to low-impact fan spray.

d. Point Spray Gun at 45°. Spray surface, working with the grain of the wood. e. Let surface dry completely, then apply stain or sealer, as needed, according to manufacturer's instructions.

cleaning Brick and Mortar

a. Inspect mortar, patching as needed. Let mortar cure according to manufacturer's instructions. b. Soak surface prior to applying detergent. c. If needed, apply brick cleaning detergent according to manufacturer's instructions. For vertical surfaces, apply detergent from bottom to top. d. Scrub stained areas as needed. e. Set Nozzle to low-impact fan spray.

tO prEVEnt DaMaGE, OnLy uSE LOW-iMpact SEttinG.

f. Point Spray Gun at 45°. Spray surface. g. Let surface dry completely, then apply sealer, as needed, according to manufacturer's instructions as needed.

7. When finished:

• Release Trigger, then set Trigger Safety Lock.

• Turn off Power Switch.

• Turn off water supply.

• Unplug the unit.

• Point Nozzle in safe direction, press Trigger to release all pressure, then release Trigger.

• Disconnect water supply hose.

• Disconnect High-Pressure Hose from unit.

• Disconnect High-Pressure

Hose from Spray Gun.

8.

iMpOrtant: cLEan tHE nOZZLE aFtEr

EVEry uSE tO Maintain SprayinG pOWEr anD prEVEnt puMp DaMaGE.

• Remove Wand from Spray Gun.

• Remove Nozzle from Wand by turning Nozzle clockwise.

• Twist Nozzle to expose tip.

nozzle tip

Blades

• Push Nozzle Tip Cleaner into tip to push out debris and buildup.

• Remove Nozzle Tip Cleaner and back-flush water through Nozzle.

• Reattach Nozzle to Wand.

• Clean and store according to

user-Maintenance instructions on page 14.

Item 63254

For technical questions, please call 1-888-866-5797.

Page 13

user-Maintenance instructions

tO prEVEnt SEriOuS inJury FrOM acciDEntaL OpEratiOn: turn the power Switch of the tool off, unplug the tool from its electrical outlet, shut off the water supply and safely discharge all residual water pressure from the unit before performing any inspection, maintenance, or cleaning procedures.

tO prEVEnt SEriOuS inJury FrOM tOOL FaiLurE:

Do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use.

cleaning, Maintenance, and Lubrication

1.

BEFOrE EacH uSE,

inspect the general condition of the tool. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• damaged cord/electrical wiring,

• damaged high-pressure hose/accessories,

• cracked or broken parts, and

• any other condition that may affect its safe operation.

2.

aFtEr uSE:

• Drain water by tipping the unit.

Frost will damage the unit if it contains water.

• Flush Detergent Bottle with water.

• Use only a clean cloth and mild detergent to clean the body of the Pressure

Washer. Do not use solvents.

Storage

• Do not immerse any part of the tool in liquid.

• Dry off any remaining water on all parts and fittings.

• Remove mineral deposits from the nozzle using a thin, stiff wire brush.

3.

pEriODicaLLy

, remove mineral buildup.

Unplug the unit and lay it face down. Fill Water

Inlet with de-mineralizing solution, following solution manufacturer's instructions. Drain de-mineralizing solution out of Water Inlet and rinse out inlet thoroughly before use.

4.

WarninG! tO prEVEnt SEriOuS inJury: if the supply cord or GFci unit of this power tool is damaged, it must be replaced only by a qualified service technician.

1. Place accessories, High-Pressure Hose and

Power Cord in their storage locations.

2. Insert Detergent Bottle into storage location under High-Pressure Hose Hook, then twist Bottle clockwise.

Spray

Gun power cord nozzle

Highpressure

Hose

3. Store in a dry, frost-free room. Flush the unit with automotive antifreeze prior to long-term storage.

Dispose of antifreeze according to local ordinances.

Page 14

For technical questions, please call 1-888-866-5797.

Item 63254

troubleshooting problem

Pressure Washer will not start

Pressure Washer stops suddenly

Output pressure varies

Trigger does not depress

Detergent will not dispense

Performance decreases over time

possible causes

1. Cord not connected.

2. No power at outlet.

Likely Solutions

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.

3. Press reset button on GFCI unit on cord.

4. Have a qualified technician service tool.

3. GFCI circuit breaker tripped.

4. Internal damage or wear.

(Carbon brushes or switch, for example.)

1. GFCI circuit breaker tripped.

2. Water leaking from housing.

1. Not enough water supply.

2. Air in water supply.

3. Water Inlet Filter is clogged.

4. Nozzle not attached to Spray Gun.

5. Nozzle is clogged.

6. Nozzle has mineral build up.

7. Water supply hose is too long.

1. Press reset button on GFCI unit on cord.

2. SHOCK HAZARD! IMMEDIATELY discontinue use.

Have the unit repaired by a qualified technician before further use.

1. Check water supply hose for kinks, leaks, or blockage. Open faucet all the way.

2. Check that all connections are tight.

3. Remove Filter and clean.

4. Pressure is created by the Nozzle, not the

Spray Gun. Attach Nozzle to Spray Gun.

5. Remove Nozzle and clean with Nozzle Tip Cleaner.

6. Remove Nozzle and clean with de-mineralizing solution.

7. Recommended water supply hose length is 25' with

5

/

8

" ID up to 50' with

3

/

4

" ID .

Shorten the length of the water supply hose if needed to increase pressure.

8. Have a qualified technician service tool.

8. Internal valves or seals may be worn or sticking.

Safety lock is still engaged.

Incorrect detergent type.

Press Trigger Safety Lock on the bottom of the

Spray Gun to release the Safety Lock.

Check that the detergent is the recommended type of detergent. Clean out dispenser and replace with correct type if needed.

Clogged with mineral deposits.

Clean unit with de-mineralizing solution.

Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service.

Item 63254

For technical questions, please call 1-888-866-5797.

Page 15

pLEaSE rEaD tHE FOLLOWinG carEFuLLy

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 16

For technical questions, please call 1-888-866-5797.

Item 63254

record product’s Serial number Here: note:

If product has no serial number, record month and year of purchase instead.

note:

Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175343741 when ordering parts.

Item 63254

For technical questions, please call 1-888-866-5797.

Page 17

parts List and assembly Diagram parts List part Description Qty

1 Tapping Screw 2

2 Cover 1

3 Motor Cover

4 Motor

5 Socket Head Screw

6 Washer

7 Bearing

8 Gear

9

10

O-Ring

Gear Shaft

11 Pump Base

12 Oil Seal

13

Deep Groove

Ball Bearing

14 Cam

1

15 Cam Screw

16 Thrust Bearing Plate

17 Thrust Bearing Roller 1

18

Thrust Bearing

Plate Hex

19 Spring Base

1

3

1

1

1

1

1

1

1

4

1

1

1

1

4

20 Piston

21 Piston Spring

22 Ring

23 Piston Body

24 Oil Seal

25 Guide Sleeve

26 Water Seal

27 O-Ring

28 O-Ring

29 Check Valve Gland

30 Pump Body

31

32

Pump Hex

Cylinder Bolt

One-Way Valve Seat

4

6

33 One-Way Valve Spring 6

3

1

1

1

3

3

3

3

3

3

3

34 One-Way Cock 6

35 One-Way Valve Cover 6

36 O-Ring

37 Seal Ring Micro

38 Water Inlet 1

6

1

39 Washer

40 Socket Head Screw

41 O-Ring

4

4

1

part Description Qty

42 Water Inlet Screw 1

43 Nut 1

44 Gasket With Filter

45 Screw

46 O-Ring

47 Socket Head Bolt

48 O-Ring

49 Water Outlet Body

50 O-Ring

51 Check Valve Core

52 Spring

53 Plug Screw

54 Socket Cover

55 Gasket With Filter

56 Socket

57 Tapping Screw

58 Micro Switch

59 Wire Socket

60 Guide Line

61 Square Jacket

62 Line Slot

63 Square Jacket

64 Jacket

65 Connector

66 Steel Ball Cover

67 Steel Ball

68 Steel Ball Spring

69 O-Ring

70 Overflow Valve Shell

71 Big Retaining Ring

72 O-Ring

73 Overflow Valve Core

74 O-Ring

75 Small Retaining Ring

76 O-Ring

77 O-Ring

78 Relief Valve Set

79

Overflow Valve

Retainer

1

1

80 Overflow Valve Spring 1

1

1

2

1

81 Feeler Lever Set

82 Connecting Rod

83 Nut

1

1

1

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

4

1

1

1

1

1

1

1

1

4

4

1

1

1

1

part Description

84 U Shaped Pin

85 Feeler Lever

Qty

1

1

86 Feeler Lever Nut

87

High-Pressure

Hose Hook

88 Tapping Screw

89 Tapping Screw

90 Tapping Screw

91 Rear Housing

92 Left Pocket

93 Right Pocket

94 Tapping Screw

95 Switch

96 Switch Cover

97 Tapping Screw

98 Staff

99 O-Ring

100 Front Housing

1

1

101 Knob

102 Handle

103 Tapping Screw

104 Wheel Cover

105 Wheel

106

Motor Bracket

Rubber Pad

107 Wire-Pressing Plate

2

108 Tapping Screw

109 Water Outlet Cover

110 Motor Protection Angle 2

111 Footing 2

112 Tapping Screw 2

1

2

1

8

2

1

1

2

113 GFCI

114 Power Cord Buckle

115 Power Cord

116 Power Cord Jacket

1

1

1

1

117 Square Jacket

118 Line Slot

119 Jacket

120 Nozzle

121 Wand

122 Spray Gun

123 High-Pressure Hose

124 Detergent Bottle

125 Nozzle Tip Cleaner

1

1

1

1

1

1

1

2

2

1

3

6

1

1

1

1

1

1

1

2

2

4

Page 18

For technical questions, please call 1-888-866-5797.

Item 63254

assembly Diagram

Item 63254

For technical questions, please call 1-888-866-5797.

Page 19

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26541 agoura road • calabasas, ca 91302 • 1-888-866-5797