Wren Kitchens 600mm Appliance Housing Base Unit Assembly Guide

BASE UNIT

600 Built Under Oven Housing

Assembly Guide

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

BASE UNIT

600 Built Under Oven Housing

Assembly Guide

BEFORE YOU START

INSTALLATION

SHOULD BE

PERFORMED BY A

COMPETENT

PERSON ONLY.

THIS PRODUCT COULD

BE DANGEROUS

IF INCORRECTLY

INSTALLED

Panel B x2 End Panel

Panel C x1 Base Panel

Panel E x2 Rail Panel

Legs x4

Filler F

(Packed separately) x1

Filler G

(Packed separately) x1

Dummy Fixing

Clip x2 Inc Screws

Large Bracket x2

Small Bracket

(FF) x2

Page 1

(F) x16

Wooden Dowel

(G) x12

Cam Dowel

(Expanding)

(H) x12

Cam Lock

REQUIRED TOOLS

(K) x4

30mm

Screw

(L) x26

15mm

Screw

(M) x4

Cover

Cap

NOT to be used with CAM DOWEL

& CAM LOCK

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

B

Seat (G) cam dowel into hole as shown.

Step 1.

Seat dowel (F) into holes in panels as shown.

Step 2.

Seat cam dowel (G) into holes in panels as shown.

BASE UNIT

600 Built Under Oven Housing

Assembly Guide

F F G G F F

G

F

B

B B

E

E

B

C

B

All Cam Locks (H) are to be positioned facing the outside of the unit carcass, for ease of tightening.

C

C

H

B

G H

G

View from underside View from underside

G F F G G F

Dowel (F)

& Cam Dowel (G) location detail

F G

Step 3.

Attach panels (C) & (E) to panels (B) , using cam dowel (G)

& cam lock (H) (in blue ), and also using dowels (F) (in orange ) in positions as shown.

Do NOT use power tools with cam dowel (G) or cam lock (H)

Step 4.

Join panels (C) & (E) to

(B) . Insert cam lock (H) .

G

F

F

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

Page 2

BASE UNIT

600 Built Under Oven Housing

Assembly Guide

Step 5.

Secure each of the legs into place with

4 x 15mm screws (L) as shown.

Front

50mm

B

C

L L

C

L

L

B

B

B

Leg position diagram

C

85mm

B

B

E

Page 3

Step 6.

Push leg firmly down into leg base.

Adjust legs to 155mm before turning carcass upright. Once in situ level accordingly.

C

B

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

K

Securing to Adjacent Units

Screw into any side units using the 30mm screws (K) provided to secure to unit. Screw at the top and bottom of both sides of the unit, place a cover cap (M) on the head to conceal it.

BASE UNIT

600 Built Under Oven Housing

Assembly Guide

L Brackets

Use 2 x 15mm screws (L) to secure each of the L brackets to the cabinets at either side.

Then screw up through into the worktop as shown.

Screws for attaching to worktop are not supplied as these vary depending on worktop material and thickness. Ensure appropriate fixings for attaching worktop are used. L brackets should only be fitted for securing wood and laminate worktops, please refer to the specialist worktop supplier if these are required for solid surface worktops.

L

L

Worktop

Screw up through the front rail into your worktop to secure it in place.

Screws for attaching to worktop are not supplied as these vary depending on worktop material and thickness. Ensure appropriate fixings for attaching worktop are used. Please refer to the specialist worktop supplier if these are required for solid surface worktops.

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

Page 4

BASE UNIT

600 Built Under Oven Housing

Assembly Guide

Small Bracket

Step 7.

Use 15mm screw (L) per small L Bracket (FF) to secure to inside face of Filler (G).

Attached equally spaced as shown.

15.5mm

from top

G inside face

155mm

Step 8.

Align Filler (G) to unit ensuring it is in line with adjacent units.

Secure Filler (G) with Small L bracket (FF) to Base of unit with

15mm Screw (L) as shown.

155mm

Filler F

Filler G

FF

G

L inside face

Page 5

FF

G

FF

FF

L

View from bottom of unit

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

BASE UNIT

600 Built Under Oven Housing

Step 9.

Secure dummy fixing clip Parts (B) onto the inside face at the bottom of panel (F), 17mm from the edge spaced evenly either side as shown, using screws (L) . Align so frontal is in line with adjacent frontals.

Part B

Dummy Fixing Clip

Part A

F

17mm from top

F inside face

17mm Part B

Step 10.

Secure dummy fixing clip parts (A) onto both

End Panels (B) using 2 x15mm screws (L) each, as shown. The top screw hole is to be positioned 45mm from the top of the panel

(marked by an indentation).

45mm from top

Part A

L inside face

Assembly Guide

Front

B

E

L

L

B

Step 11.

Align and push panel (F) into place. Ensure frontal is in line with adjacent units. Space appropriately from carcass.

F

F B

B

B

View from inside of unit

For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

Page 6