advertisement
MODEL VTD1420/VTD2020 USER GUIDE
DIGITAL VIDEO
Region discs only
5J20301A Cov-In 1
Combination TV and
DVD Video Player
TELETEXT
23/4/03, 1:04 PM
IMPORTANT
Unauthorized recording of copyright television programmes, films, video tapes and other materials may infringe on the rights of copyright owners and be contrary to copyright laws.
WARNING
To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
MAINS SUPPLY
This unit is designed to operate from AC 230V~240V 50Hz household mains supply.
This unit is supplied with an approved 13 amp (BS 1363) fused mains plug. When replacing the fuse always use a 5 amp (BS 1362) approved type.
Never use this plug if the fuse cover is missing. To obtain a replacement fuse cover contact your store.
If the mains sockets in your home differ or are not suitable for the type of plug supplied, then the plug should be cut from the mains lead and a suitable type fitted.
WARNING: If the mains plug is cut from the mains lead of this appliance the plug must be destroyed. A mains plug with bared wires is hazardous if engaged in a mains output line socket.
You must use a 13 amp plug (BS 1363) and fit a 5 amp fuse (BS 1362). If any other type of plug is used a 5 amp fuse must be fitted, either in the plug, adaptor or at the distribution board.
WIRING INSTRUCTIONS
The wires in the mains lead are coloured in accordance with the following code:
BLUE
BROWN
—
—
NEUTRAL
LIVE
As the colours of the wires in the mains lead of the appliance may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
No connection is to be made to the Earth (E, ) terminal.
N
E
L
CAUTION:
THIS UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM
WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE PLAYER CORRECTLY AS INSTRUCTED.
THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE UNIT.
CLASS 1
LASER PRODUCT
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE
OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PER-
SONNEL.
5J20301A Cov-In 2 23/4/03, 1:04 PM
TV
• Auto Channel Memory
• TELETEXT Function
• On-Screen Programming
• Picture Control Adjustments
• Auto Power Shut Off
• On Screen 5 Language Display
• Sleep Timer
FEATURES
• Multi-Language
• Multi-Angle
• Repeat Playback
• Memory/Random Playback
• Zoom
• Video Aspect Ratio
• Parental Control
• Digital output for Dolby Digital (AC-3) and DTS
• Playback of DVD, Video-CD, Audio-CD and
MP3-CD
• PAL & NTSC DVDs playback
• A-B Repeat playback
DVD Player
• Digital Audio Jack (Coaxial)
CONTENTS
PREPARATION
PRECAUTIONS ......................................................... 2
LOCATION OF CONTROLS ...................................... 3
REMOTE CONTROL ................................................. 4
AERIAL CONNECTIONS ........................................... 6
CONNECTION TO OTHER EQUIPMENT ................. 7
TV OPERATION
LANGUAGE SETTING .............................................. 9
PRESETTING THE CHANNELS ............................. 10
TV OPERATIONS .................................................... 13
CONVENIENT FUNCTIONS ................................... 14
PICTURE ADJUSTMENTS ...................................... 15
AV COLOUR ADJUSTING ...................................... 16
RECEPTION OF INTERFERENCE ......................... 17
TELETEXT ............................................................... 18
ADVANCED FUCTION OF DVD SECTION
SETTING THE ASPECT RATIO OF TV SCREEN .. 31
SETTING ON SCREEN DISPLAY ........................... 31
DYNAMIC RANGE CONTROL ................................ 32
PARENTAL CONTROL SETTING ........................... 33
TO CHANGE THE PARENTAL LEVEL ................... 34
TEMPORARY DISABLING OF RATING LEVEL BY
DVD DISC ................................................................ 35
ADDITIONAL INFORMATION
LANGUAGE CODE LIST ......................................... 36
BEFORE REQUESTING SERVICE ......................... 37
SPECIFICATION ................................. BACK COVER
DISC PLAYBACK OPERATION
DISC ........................................................................ 20
PREPARATION ....................................................... 21
STATUS DISPLAY OF DISC ................................... 21
SETTING LANGUAGE ............................................ 22
PLAYBACK PROCEDURE ...................................... 23
SPECIAL PLAYBACK .............................................. 24
MP3 PLAYBACK ...................................................... 25
ZOOMING ................................................................ 26
LOCATING DESIRED SCENE ................................ 26
REPEAT/RANDOM/PROGRAM PLAYBACK AND
REPEAT A-B ............................................................ 27
MARKING DESIRED SCENES ............................... 28
CHANGING SOUNDTRACK LANGUAGE/
SUBTITLES ............................................................. 29
CHANGING ANGLES .............................................. 30
TITLE SELECTION .................................................. 30
DVD MENU .............................................................. 30
* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation or other rights owners and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights owners. Reverse engineering or disassembly is prohibited.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe the rights of copyright owners and be contrary to copyright laws.
1
5J20301A P01-07 1 23/4/03, 1:04 PM
PRECAUTIONS
DO read the operating instructions before you attempt to use the equipment.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO NOT remove any fixed cover as this may expose dangerous voltages.
DO NOT place hot objects such as candles or nightlights on, or close to, the equipment. High temperatures can melt plastic and lead to fires.
Under certain conditions, such as low humidity or walking across wool carpet, you may experience a static discharge when touching the unit. If this happens and it fails to function, follow the procedure below.
1) Un-plug the unit from the AC outlet.
2) It may take two to three hours for the static build up to clear.
3) Re-plug the unit again.
Do not place the unit on or near appliances which may cause electromagnetic interference eg. TV or hi-fi speakers, etc. Doing so may affect operation of unit causing erratic playing or recording, picture or sound distortion, or noise.
Avoid extreme heat and cold.
Do not block the ventilation holes.
Place the unit at least 10 cm away from the walls for good air circulation.
10cm
Keep the unit away from flower vases, sink etc.
Liquids spilled into the unit can cause serious damages. Switch OFF the Power Supply to the unit and consult a qualified service engineer before attempting to use the unit again.
To protect the unit during a thunder storm, unplug the AC mains lead from the wall outlet and disconnect the aerial.
2
5J20301A P01-07 2 23/4/03, 1:04 PM
Front
LOCATION OF CONTROLS
Disc tray
STAND BY ( ) Indicator
Power ( ) button
Rear
Remote sensor
OPEN/CLOSE button
VOLUME / buttons
CHANNEL / buttons
PLAY button
Phones socket
VIDEO/AUDIO IN (L/R) jacks (AV2)
Forward SKIP button
Reverse SKIP button
STOP button
Indoor Aerial Holder
Mains Lead
5J20301A P01-07
21 pin SCART/PERITEL (AV1)
COAXIAL DIGITAL AUDIO OUT jack
3 23/4/03, 1:04 PM
3
REMOTE CONTROL
page
TV/DVD
OPEN/CLOSE
ON/STANDBY
0-9
Select to operate TV or DVD
Open or Close the tray
Power on/off
Direct channel selection of TV
8,9,13,21
23
9
13
VOLUME ▲ / ▼
MUTE
CALL
0/AV
TEXT/MIX/TV
MARKER
TOP MENU
SUBTITLE
AUDIO
ANGLE
SETUP/MENU
DVD MENU
CANCEL
ZOOM/
CH RTN
CH/PAGE ▲ / ▼
Input setting
Enter a security code
Volume Up/Down
Mute
Display TV or DVD operation status
Scart Input or AV-Front input
Select teletext
Index for DVD
Select title of a DVD disc
Set Subtitle of a DVD disc
Change sound track language of DVD
Change playback angle of a DVD disc
Display menu of setup
Select menu of a DVD disc
Zoom (for DVD playback)
26,27
33,34
13
14
14,21
14
18
28
9~12,15~16,22,31~34
30
Cancel input data in the setting mode 14,15,26,28,33,34
Switch between present/last channel
Select channel of the TV
26
14
13,14
▲ / ▼ / B / A
RETURN
SELECT/ENTER
Utilize the teletext
Cursor buttons
Remove DVD set up menu
SEARCH 8 / 9 Reverse search or Forward search playback
19
22,31
Enter information in the menu/Select option in the menu
24
30
29
29
30
REVEAL
PLAY
SUB PAGE
JUMP
SKIP /
HOLD
STOP
F/T/B
Reveal
Playback
Sub page
Locating desired scene
Skip chapter to forward or reverse direction
Hold
Stop
F/T/B
REPEAT A-B
SLOW ˆ / ]
Repeat playback between A and B (DVD/CD)
Slow motion playback
Four Coloured buttons Access the Teletext
PAUSE Still picture
PLAY MODE Select playback mode
27
24
18
24
27
24
18
23
19
19
23
19
26
4
5J20301A P01-07 4 23/4/03, 1:04 PM
REMOTE CONTROL
BATTERY INSTALLATION
Open the battery compartment cover in the direction of the arrow.
Install two “AAA/R03/UM-4”
(penlight size) batteries, paying attention to the polarity diagram in the battery compartment.
Replace the cover.
BATTERY CAUTIONS
• Use two "AAA/R03/UM-4" size penlight batteries for the remote control transmitter.
• The batteries may last approximately one year depending on how much the remote control is used. For best performance it is recommended batteries be replaced on a yearly basis, or when remote operation becomes erratic.
• Do not mix old and new batteries.
• Weak batteries can leak and severely damage the remote control transmitter. Always remove batteries as soon as they become weak.
EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER
NOTES: • When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the remote sensor, the remote operation may be unstable.
• When there is an obstacle between the unit and the transmitter, the remote control transmitter may not operate.
5
5J20301A P01-07 5 23/4/03, 1:04 PM
AERIAL CONNECTIONS
Connect an indoor or outdoor aerial to the aerial socket at the rear panel as shown below.
For all aerial circuit problems, please consult your local dealer.
(A)
(B)
RF IN
Aerial socket
(A) INDOOR AERIAL
A loop aerial is supplied with the unit (VTD1420 only). Insert the aerial holder into the mounting hole on the back cabinet until it locks into place. Insert the aerial adaptor (supplied with VTD1420 only) to the aerial socket. Adjust the angle of the loop aerial to receive the best possible picture.
(B) EXTERNAL AERIAL
The type of aerial required depends on the position of your home, it's distance from the transmitter and local interference. If you do not have an aerial and you are uncertain of what to buy, you should seek the advice of a local aerial contractor.
6
5J20301A P01-07 6 23/4/03, 1:04 PM
CONNECTION TO OTHER EQUIPMENT
The exact arrangement you use to interconnect various video and audio components to the unit is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.
Using an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround sound decoder (such as Dolby Digital / DTS / MPEG / etc.), you can connect it as shown below.
Rear of unit
This unit
Subwoofer
Front
Speaker
(Right)
Front
Speaker
(Left)
Coaxial Digital Audio Output
Coaxial digital cable (not supplied)
To Coaxial Digital Audio Input
Center Speaker
Surround
Speaker (Left)
Surround
Speaker (Right)
AV Amplifier with built-in digital surround decoder as listed above
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
*
Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc.. All rights reserved.
DTS and DTS Digital Out are trademarks of Digital Theatre Systems, Inc.
NOTES:
• When you make the connections above, make sure that the power of all units is switched off at the mains.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
• When playing DTS encoded material, the sound will only be available through the Digital Audio Output Socket.
23/4/03, 1:04 PM
7
5J20301A P01-07 7
CONNECTION TO OTHER EQUIPMENT
Input Selection
If you connect the unit to a VCR, camcorder or games console, you can select this input by pressing the 0/AV button.
AV1(Scart socket)
Press the TV/DVD button to select TV mode and then press the 0/AV button repeatedly to select AV1 or AV2.
AV2(Front-AV-input)
AV1
1. To connect the unit to a VCR
Press the 0/AV button to select AV2 to use the TV as a monitor.
TV-program
Front of unit
VIDEO IN
AUDIO IN (R)
AUDIO IN (L) To Scart socket of VCR
Scart cable (not supplied)
2. To connect the TV to a TV Game
The unit can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. Press the 0/AV button to select AV2 to use the TV as a monitor. You'll need to consult each component's Owner's Manual for additional information.
Front of unit
VIDEO IN
To Audio/Video OUT AUDIO IN (R)
AUDIO IN (L)
Audio/Video cord (not supplied)
3. To connect the TV to a camcorder
Connect the camcorder to the unit as shown.
Press the 0/AV button to select AV2 to use the TV as a monitor.
Front of unit
Camcorder VIDEO IN
AUDIO IN (R)
AUDIO IN (L)
Audio/Video cord (not supplied)
4. To connect the unit to another TV set (ie. a widescreen set) (see P.31)
Connect the unit and another TV set with a Scart cable.
Press the AV button on another TV to monitor the input from the Scart cable.
8
5J20301A P08-17 8 23/4/03, 1:04 PM
This unit has 5 different languages for
MENU set up which can be selected through ON Screen Display: English,
German, French, Italian or Spanish.
LANGUAGE SETTING
PREPARATION
Press Power ( ) on the front panel of the unit. Then press ON/
STANDBY on the remote control to turn on or off your unit.
1
Press TV/DVD to select TV mode. Then press SETUP/
MENU.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS:
▲ / ▼
/ ENTER / MENU
2
To select the LANGUAGE mode, press or , then press
SELECT/ENTER.
MENU
CHANNEL SETUP
PICTURE
LANGUAGE
PRESS:
▲ / ▼ / ENTER / MENU
3
To select the desired language,
English (ENGLISH), Spanish
(ESPANOL), French (FRANCAIS),
German (DEUTSCH) or Italian
(ITALIANO), press or .
Then press SELECT/ENTER.
LANGUAGE/SPRACHE/LANGUE
LINGUA/LENGUA
ENGLISH
DEUTSCH
FRANCAIS
ITALIANO
ESPANOL
PRESS: ▲ / ▼ / ENTER / MENU
4
Press SETUP/MENU to return to the normal TV screen.
NOTES:
• If you are using this unit for the first time, step 1 and 2 of the MENU screen will not be shown. The Language selection menu will be shown.
• To turn your unit off completely, switch off the Power ( ) button on the front panel.
5J20301A P08-17 9 23/4/03, 1:04 PM
9
PRESETTING THE CHANNELS
Once you have connected up this unit, you will need to tune in the channels in order to watch TV stations. There are two ways that you can do this:
- Automatic tuning The stations will be preset in the order that they appear when the automatic
- Manual tuning tuning is activated.
In this mode the TV searches until a picture appears. If it is a station that you want to keep, you can choose which channel preset you want to store it on.
You repeat this procedure for each station until you have stored all the desired stations.
AUTOMATIC TUNING
1
Press SETUP/MENU.
Press or to select the
CHANNEL SETUP mode, then press SELECT/ENTER.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS:
▲ / ▼
/ ENTER / MENU
2
Press or to select the
AUTO mode, then press
SELECT/ENTER.
CHANNEL SETUP
MANUAL
AUTO
CH ALLOCATION
PRESS:
▲ / ▼ / ENTER / MENU
3
All available channels in your area are automatically scanned and stored in the memory of the unit.
When the unit finds a broadcasting channel, the mark disappears.
After scanning, the previous step
2 screen appears.
CH position
CH 10
Searching direction
Tuning segment bar
4
Press SETUP/MENU twice.
The unit will return to normal TV screen.
5
The automatic tuning will not necessarily store the channels in the correct order (BBC1 on CH 1 etc.). If you want to change the order of the stored channels, please see page
12.
NOTES:
• If you want to skip any channels, refer to page 14.
• When the unit is in the AV mode, you can’t preset the channels.
10
5J20301A P08-17 10 23/4/03, 1:04 PM
5J20301A P08-17 11
PRESETTING THE CHANNELS
MANUAL TUNING
How to tune a station to channel 10 position.
1
Press SETUP/MENU.
Press or to select the
CHANNEL SETUP mode, then press SELECT/ENTER.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS:
▲ / ▼ / ENTER / MENU
2
Press or to select the
MANUAL mode, then press
SELECT/ENTER.
CHANNEL SETUP
MANUAL
AUTO
CH ALLOCATION
PRESS: ▲ / ▼ / ENTER / MENU
3
Press or until the picture appears on screen. If this is not your desired channel, press or until your desired channel appears.
If you need to make the picture clearer, use or (FINE
TUNING).
Then press SELECT/ENTER.
CH 1
SEARCH:
B A
/ F.TUNE:
CD
4
Press or to select channel position No.10, then press
SELECT/ENTER.
CH 10
PRESS: ▲ / ▼ /ENTER/MENU
5
Repeat step 3 through 4 until all the required channels have been stored.
6
When all desired channels have been set in your required position, press SETUP/MENU three times to return to normal
TV screen.
23/4/03, 1:04 PM
11
PRESETTING THE CHANNELS
TO CHANGE THE CHANNELS
EXAMPLE: Changing of channel position from CH2 and CH5.
1
Press SETUP/MENU.
Press or to select the
CHANNEL SETUP mode, then press SELECT/ENTER.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS:
▲ / ▼
/ ENTER / MENU
2
Press or to select the CH
ALLOCATION mode, then press
SELECT/ENTER.
CHANNEL SETUP
MANUAL
AUTO
CH ALLOCATION
PRESS:
▲ / ▼ / ENTER / MENU
3
Press or to select the channel position No. (broadcasting) which you want to change.
Then press SELECT/ENTER.
CH 2
CH ALLOCATION CH 1
PRESS:
▲ / ▼
/ ENTER / MENU
4
Press or to select the channel allocation No. that you want to change to.
CH 2
CH ALLOCATION CH 5
PRESS: ▲ / ▼ / ENTER / MENU
5
Press SELECT/ENTER. The numbers of the stations are changed. Repeat steps 3 - 4 to change the order of other channels. Then press SETUP/
MENU three times to return to normal TV screen.
CH 2
Before setting
CH 5
CH ALLOCATION CH 2
PRESS: ▲ / ▼ / ENTER / MENU
CH 5
CH 2 CH 5
After setting
12
5J20301A P08-17 12 23/4/03, 1:04 PM
After completing the connection and presetting the channels, follow these steps for viewing.
TV OPERATIONS
1
Press Power ( ) on the front panel of the unit. Then press
ON/STANDBY on the remote control (STANDBY indication will goes off). Press TV/DVD to select TV mode.
2
Direct Channel Selection buttons (0-9)
Press the Direct Channel Selection button on the remote control.
1-9 CH: Press your required number only.
10-80 CH: Press the two digits in accordance to the channel numbers required.
CH/PAGE /
Press CH/PAGE or on the remote control.
CH 29
3
The VOLUME can be adjusted by pressing the VOLUME or
on the remote control.
VOLUME 30
NOTE:
On screen display will disappear after 4 seconds.
Automatic Power Shut Off
If a station being viewed stops broadcasting for about 15 minutes, the unit will automatically shut itself off and go into stand by mode.
5J20301A P08-17 13 23/4/03, 1:04 PM
13
CONVENIENT FUNCTIONS
The following functions are available from the remote control handset only.
TV/AV Selection
For receiving the desired signal:
Press 0/AV to select the TV or AV mode.
CH 5 AV1
TV position - to view a normal TV.
AV position - to receive through the direct Video input. AV1 (from 21 pin
SCART socket on the rear) or AV2 (from Audio/Video in jacks on the front) indicator appears on the screen in AV mode.
CHANNEL RETURN
This button allows you to go back to the previous channel by pressing CH RTN. Press this button again to return to the channel you were watching.
CALL
When you press this button once, the channel number will appear. Press this button again, then the display will disappear.
MUTE
When MUTE is pressed, the TV sound will be turned off completely. To disable this function, press the button again or VOLUME or .
SKIP FUNCTION
After all channels available in your area have been set in memory, you can skip unwanted channels as follows.
1
Press CH/PAGE or to select the channel which you want to skip.
2
Press CANCEL.
When a channel is skipped, the channel number will blink.
3
Skip all unwanted channels the same way following step 1-2.
NOTE:
To cancel the SKIP function, press DIRECT CHANNEL
SELECTION (numeric buttons) to select the channel which you want to cancel, then press CANCEL again.
14
5J20301A P08-17 14 23/4/03, 1:04 PM
The picture settings have been adjusted at the factory under optimum signal reception conditions. However, you can adjust for BRIGHTNESS,
CONTRAST, COLOUR and SHARP-
NESS to your preference.
PICTURE ADJUSTMENTS
1
Press SETUP/MENU.
2
Press or to select the
PICTURE mode, then press
SELECT/ENTER.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS:
▲ / ▼ / ENTER / MENU
3
To adjust the BRIGHTNESS, press or , then press .
BRIGHTNESS
PRESS: B / A / C / D /MENU
0
NOTE: Each time is pressed, the on screen display will change as shown below.
BRIGHTNESS CONTRAST COLOUR
(TINT) SHARPNESS
Press SETUP/MENU twice to return to normal TV screen.
NOTES:
• The picture settings can only be adjusted when they are displayed on screen.
• Pressing CANCEL will return all adjustments to their factory preadjusted levels. This function is available in adjusting picture mode.
• TINT will appear only when the NTSC
Colour System is selected.
5J20301A P08-17 15 23/4/03, 1:04 PM
15
AV COLOUR ADJUSTING
When connecting external equipment to the unit, the picture may become black and white. This can be corrected by selecting AV (Extension) Colour as follows.
1
Press SETUP/MENU on your remote control. The on screen display will appear.
Press ▲ or ▼ to select the AV
COLOUR menu.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS: ▲ / ▼ / ENTER/ MENU
2
Press SELECT/ENTER to select one of the colour options,
PAL or NTSC4.43.
• Usually select the PAL option.
3
Press SETUP/MENU to remove the menu from the screen.
16
5J20301A P08-17 16 23/4/03, 1:04 PM
RECEPTION OF INTERFERENCE
The most common types of television interference are as follows.
IGNITION
Black spots and horizontal streaks may appear, the picture may flutter or drift. This is usually caused by interference from car ignition system, neon lamps, electric drills or other electrical appliances.
IGNITION
GHOSTING
Ghosting is caused by the TV signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or similar obstruction. Changing the direction and/or position of the aerial may improve reception.
GHOSTING
SNOW
If your TV is located on the fringe area of a TV station, where the signal is weak, your picture may be affected by the appearance of small dots (SNOW). It may be necessary to install a stronger aerial to improve the picture.
SNOW
RADIO FREQUENCY INTERFERENCE
This kind of interference produces moving ripples or diagonal streaks and in some cases loss of contrast in the picture.
RADIO FREQUENCY
INTERFERENCE
5J20301A P08-17 17 23/4/03, 1:04 PM
17
TELETEXT
Most broadcasting stations offer a Teletext service in addition to their standard TV program.
Teletext offers news, weather forecast, winning Lotto numbers, TV listings and other interesting news.
The text is received page by page, as soon as you select the broadcasting station. A single page can be displayed on the screen. The pages are numbered and broadcasted one by one. Therefore you'll have to wait a certain time until the selected page is displayed on the screen. The page will be displayed as soon as it is broadcast.
Certain pages can be displayed more easily by pressing one of the FOUR COLOURED TELETEXT buttons.
Basic operation
1
Select the broadcasting station, whose text you want to read. In order to do so, select the station's channel with the remote handset.
2
Push TEXT/MIX/TV button.
The first push on the TEXT/MIX/TV button switches the Teletext on.
The second push on TEXT/MIX/TV displays the TV program and the Teletext together (MIX).
The third push on the TEXT/MIX/TV button switches the Teletext off and returns the screen back to the TV program.
The first operation of the teletext normally opens the page 100 with the table of contents.
Example for a teletext page:
P100 TELETEXT 100 JAN 1 12 : 00 : 00
Selected page number
Teletext service name
Displayed page number
(scrolls when searching)
Date
Time
Press the red
Fastext key to access information
Press the green
Fastext key to access information
Press the yellow
Fastext key to access information
Press the blue
Fastext key to access information
TV GUIDE SPORT NEWS WEATHER
Select the desired teletext page from the broadcasting station's table of contents.
HOLD
Some pages hold more text than can be displayed on one page. The broadcasting station separates these pages into sub-pages, which are broadcasted one by one automatically. To study one sub-page thoroughly push the HOLD button.
The HOLD-symbol will be displayed.
The associated sub-pages will scroll through automatically, when you push HOLD a second time to release it.
18
5J20301A P18-19 18 23/4/03, 1:04 PM
TELETEXT
To call a teletext page
Leaf through the pages with the PAGE ( M / ?
) - button (forward or backward).
Note: You will not necessarily find a page for every page number you enter. E.g. you have entered page no. 116 but it does not offer this page. Available page numbers can be found on the Index page (most stations offer this page 100).
Enter the three-digit page number with the number buttons.
Example:
You want to display page 300.
Enter: 3 then 0 and 0.
If you enter an incorrect digit, complete all three digits with any numbers, then you can enter the correct page number.
Inside the teletext mode you cannot change to another broadcasting station.
To switch to another channel, leave the teletext mode by pushing the TEXT/MIX/TV button.
How to call a specific sub-page
Push SUB PAGE button (0000).
The screen's left upper corner will display: - - - -
To call sub-page 2 enter: 0 0 0 2 .
Your input will be displayed in the left upper corner: 0002.
It may take some time until sub-page 2 is broadcast.
The sub-page can only be displayed when the broadcaster transmits it.
To leave sub-page mode push the SUB PAGE button again.
Within the sub-page mode no other pages other than the sub-pages of the selected page can be called. To call other teletext pages you must leave the sub-page mode.
Magnifying
To magnify the letters push F/T/B button.
You can magnify either the upper or the lower half of the screen.
Each push on the F/T/B button switches between the screen's upper and lower half and the full screen.
(F/T/B = Full / Top / Bottom)
REVEAL
Pushing REVEAL will give you the hidden answers to the questions on a Quiz-page.
Not every broadcasting station offers Quiz-pages and they are not constantly offered.
19
5J20301A P18-19 19 23/4/03, 1:04 PM
DISC
DVD discs must be Region 2 type to play on this unit.
The loaded Disc (DVD, Video-CD and Audio-CD) will be recognized automatically.
The suitable Disc-formats are: DVD, CD-R and CD-RW.
Some CD-R/RW discs may be incompatible.
Do not play DVD-ROM, DVD-Audio, CDV, CD-G or Photo CD to prevent accidental erasure of prerecorded material.
Some DVDs are copy protected and forbid dubbing on to video tape. Picture Distortion will occur. This is not a defect of this unit.
Title
When two or more movies are recorded on a disc, the disc is divided into two or more sections. Each section is called a “TITLE”.
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Track
An Audio CD can contain several items.
These are assigned to tracks.
DVD DISC
TITLE1
CHAPTER 1 CHAPTER 2 CHAPTER 1
TITLE2
CHAPTER 2 CHAPTER 3
TRACK 1 TRACK 2
Audio-CD
TRACK 3 TRACK 4 TRACK 5
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe in circular direction.
• Do not use liquid or aerosol cleaners.
20
5J20301A P20-29 20 23/4/03, 1:05 PM
PREPARATION/STATUS DISPLAY OF DISC
The following pages describe the setup/operation in DVD mode.
Preparation
Before DVD/CD operation, please make preparations as follows.
1
Insert the AC cord plug into a standard 230V~240V 50Hz AC outlet.
• If the AC cord plug is plugged in for the first time, wait for about 5 seconds before pressing ON/STANDBY.
NOTE: When connecting to other equipment, unplug the unit from the AC outlet.
2
Press ON/STANDBY on the remote control to turn on the unit.
• Every time you press ON/STANDBY, the unit starts from
TV mode.
• When using an amplifier, switch on the amplifier.
3
Press TV/DVD to select DVD mode.
The DVD startup screen will appear on the screen.
No Disc welcome
Status display of disc
Press CALL. The status display of the disc will appear on the screen.
DVD
Title number Title elapsed playing time
Chapter number Title total time
Disc operation
T 1/8 C 1/19 0:07:18 2:02:31
1/8 Eng DolbyDigital 1/8 Eng 1/1 Camera angle
NOTE:
If the unit does not operate properly:
Static electricity can adversely affect the operation of this player. Sometimes this can be remedied by unplugging the unit for a short time, then reconnecting it.
Audio language Subtitle language
Type of audio
To make status display disappear, press CALL again.
Audio CD/Video CD
PBC (PlayBack Control) on Video CD
Track elapsed playing time
Disc operation
Track number
Play list
T
PBC
1 / 8 0:02:31 0:53:09
Playlist
01 02 03 04 05 06 07 08
Track total time
5J20301A P20-29 21
• When you play the CD disc, the status display will appear on the screen and continue displaying.
• When you play the Video CD, Play list will not appear on the screen.
21
23/4/03, 1:05 PM
SETTING LANGUAGE
You can change the default settings to customise performance to your preference.
1
Press TV/DVD to select DVD mode.
Press SETUP/MENU in the stop mode.
Press or to select
“Language”, then press or SELECT/ENTER.
2
Press or to select
“OSD Language”, then press
or SELECT/ENTER.
Main Menu
Language
Picture
Sound
Parental
/Enter/Setup/Return
Language
OSD Language English
Menu
Audio
Subtitle
English
English
English
/Enter/Setup/Return
3
Press or to select desired language (e.g. English), then press SELECT/ENTER.
The menu returns to “Language” menu automatically.
• If you want to return to the previous menu, press or RETURN.
OSD Language
English
Francais
Espanol
Deutsch
Italiano
/Enter/Setup/Return
4
Repeat steps 2-3 for other “Language” setting.
Other Selection: (Menu/Audio/Subtitle)
If you want to select another language, enter the language code (see the Language code list on page 36).
Off: (subtitle)
Subtitles do not appear.
5
Press SETUP/MENU to remove the Menu screen.
NOTES:
• If the selected soundtrack language is not recorded on the disc, the original language will be heard.
• If the selected subtitle language is not recorded on the disc, the first-priority language is selected.
22
5J20301A P20-29 22 23/4/03, 1:05 PM
NOTES:
• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen according to the type of loaded disc. If these appear, check your disc again (see pages
20 and 33).
• Some discs may take a minute or so to start playback.
• When you set a single-faced disc label downwards (ie. the wrong way up) and press (PLAY) or (OPEN/CLOSE) on the unit, “ ” will appear on the display for approx. 5 seconds and then “No
Disc” will be displayed.
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.
5J20301A P20-29 23
PLAYBACK PROCEDURE
1
Press (OPEN/CLOSE) on the unit or OPEN/
CLOSE on the remote control.
The disc tray will open.
2
Place a disc onto the tray.
Position it with the printed label side up, align it with the guides, and place it in its proper position.
3
Press PLAY.
The disc tray closes automatically.
On the TV-screen, “ ” changes to “ ” and then playback commences.
• A menu screen will
appear on the TV screen,
if the disc has a menu
feature.
4
Press / or / to make a selection.
5
Press SELECT/ENTER.
• Title is selected and play commences.
6
Press STOP to end playback.
• The unit memorizes the stopped point, depending on the disc. “ ” appears on the screen. Press PLAY to resume playback (from the scene point).
• If you press STOP again or unload the disc (“ ” appears on the screen.), the unit will clear the stopped point.
7
To stop the playback, press STOP.
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press ON/STANDBY.
The disc tray closes automatically and unit turns off.
23
23/4/03, 1:05 PM
SPECIAL PLAYBACK
Note: There may be a slight delay between when you press the button and the function activating.
Fast Forward Playback
Press SEARCH during normal playback.
Each press of the SEARCH button will increase the speed of the search (x 2),
(CD: (x 2), (x 4),
(x 4),
(x 8),
(x 8),
(x 20))
(x 15).
• To resume normal playback, press PLAY.
Review Playback
Press SEARCH during normal playback.
Each press of the SEARCH button will increase the speed of the search (x 2), (x 4), (x 8), (x 15).
(CD: (x 2), (x 4), (x 8), (x 20))
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE during normal playback to pause playback.
NOTE:
The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent damage to your television screen. Projection televisions are very susceptible.
24
5J20301A P20-29 24
To resume normal playback, press PLAY.
Frame Advance
Press PAUSE during still playback.
One frame is advanced each time you press PAUSE.
To resume normal playback, press PLAY.
Slow-motion Playback
Press SLOW / during normal playback or still playback.
Each press of SLOW / will change the speed of the slow x1/2, x1/4, x1/6, x1/8.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE.
• Audio CD does not work in above operation.
Locating a chapter or track
Press SKIP( 7 ) Forward or SKIP( 6 ) Reverse during playback to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped.
23/4/03, 1:05 PM
This player can play back the MP3-data which has been recorded on CD-R or CD-
RW. To produce the MP3-data, you need a
Windows-PC with CD-ROM drive and a MP3encoding Software (not supplied).
The Apple-HFS-System can not be played.
MP3 CD Information
Limitations on MP3 CD playback
• MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits extension letters, “mp3”.
• The directory and file names of the MP3
CD must be correspond to the ISO standardized files.
• This unit can read 200 files per disc. If one directory has more than 200 files, it reads up to 200 files, the remaining files will be omitted.
• MP3 CD’s cannot be used for playback for the purpose of recording.
• It may take more than one minute for this unit to read MP3 files depending on its structure.
• Music recorded by “Joliet Recording
Specification” can be played back, the file name is displayed on the screen.
• The music files recorded by “Hierarchical
File System” (HFS) cannot be played.
Notes on MP3 files
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data alphabetically or numerically.
2. Name each file including two-digit or threedigit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
CAUTION:
• Some MP3 CDs can not be played back depending on the recording conditions.
• The CD-R/RW that has no music data or non-MP3 files can not be played back.
MP3 PLAYBACK
•
•
Preparation:
Turn on the unit.
Press TV/DVD to select the DVD mode.
1
Press (OPEN/CLOSE) on the unit or OPEN/CLOSE on the remote control.
The disc tray will open.
Place a disc onto the tray.
2
Press PLAY. The disc tray closes automatically. On the TV-screen,
“Scanning...” will appear. Scanning will take as much time as the number of file.
Scanning...
3
A MP3 menu screen will appear on the TV screen.
Press / or / or Number
buttons (0-9) to select the desired track, then press SELECT/EN-
TER. Track is selected and play commences.
T -/18
01 –
/
02 –
03 –
04 –
05 –
06 –
07 –
08 –
09 –
10 –
0:00:00
Japan
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes flower
Lies and Truthwinter fall
/Enter/0-9/PlayMode
• In case the folder includes more than 11 tracks, press or to display next track list.
4
Press STOP to end playback.
• The unit records the stopped point. “ ” appears on the screen. Press PLAY to resume playback (from the scene point).
• If you press STOP again or unload the disc, the unit will clear the stopped point.
5
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press ON/STANDBY.
The disc tray closes automatically and the unit turns off.
NOTES:
• During MP3-Playback, you cannot use search, A-B
Repeat functions.
• You can use Repeat (Track or All), Random functions and
Program playback for MP3 CD Playback. (See page 27)
25
5J20301A P20-29 25 23/4/03, 1:05 PM
ZOOMING/LOCATING DESIRED SCENE
Zooming
This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.
1
Press ZOOM during playback.
The centre part of the image will be zoomed in.
Each press of ZOOM will change the ZOOM 1
(x 2), 2 (x 3) and 3
(x 4).
1
2
Press / or / to view a different part of the frame.
You may move the frame from the centre position to UP,
DOWN, LEFT or RIGHT direction.
3
In the zoom mode press ZOOM repeatedly to return to a
1:1 view ( Off).
NOTES:
• You can select the Pause, Slow or Search playback in the zoom mode.
• Some discs may not respond to zoom feature.
Locating Desired Scene
Use the title, chapter and time recorded on the disc to locate the desired point to play back.
1
Press JUMP during playback.
Jump
C
T
_ _ / 19
1 / 8
0:00:00 / 2:02:31
/Enter/0 9/Cancel/Jump
2
Press or to select the “ C (Chapter)”, “ T (Title/
Track)” or “ (Time)”.
3
Press Number buttons (0–9) to input the number.
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
numbers.
4
Press SELECT/ENTER.
• Playback starts.
• When you change the title, playback starts from
Chapter 1 of the selected title.
• Some discs may not work in the above operation.
26
5J20301A P20-29 26 23/4/03, 1:05 PM
REPEAT/RANDOM/PROGRAM PLAYBACK AND REPEAT A-B
Press PLAY MODE during playback or stop mode.
Each time you press PLAY MODE, playback mode changes as follows.
DVD
On screen display
Operation
→
Title:
↓
Repeats the current title.
Chapter: Repeats the current chapter.
↓
Off: Resumes normal playback.
• During stop mode, PLAY MODE key is not effective.
Audio CD/MP3 CD/Video CD
On screen display
Operation
→
All:
↓
Track:
↓
Repeats entire disc.
Repeats the current track.
Random Play: Plays the tracks in random order.
↓
*Program:
↓
Plays the tracks in program order.
(Status display): Resumes normal playback.
• During stop mode, you can not select “ Track”.
• Random playback and Program playback do not function on the Video CD.
*Program menu
Use number buttons (0–9) to enter the track’s number you want to program, then press
SELECT/ENTER. The track number and total time are displayed. Repeat this step to enter additional tracks. When you have finished entering tacks,
NOTES:
• If you put a wrong number, press CANCEL.
press PLAY to start Program playback.
A playlist of your programmed tracks is displayed.
• To cancel program play, press STOP 3 times.
• To clear the programs on the program menu, press CANCEL until all programs will be cleared.
• The program is cancelled when you open the disc tray or turn off the power.
Repeat A-B
Repeat A-B playback allows you to repeat material between two selected points.
1
Press REPEAT A-B during playback.
The start point is selected.
Program
1 5 8:29
2 8 8:54
3 3 7:31
4 __
Total 3 0:24:54
/Enter/0 9/Cancel/Play/PlayMode
T 5 / 8
Playlist
05 08 03
Program Playback
0:02:31 0:08:29
A
2
Press REPEAT A-B again.
The end point is selected. Playback starts at the point that you selected. Playback stops at the end point, returns to Point A automatically, then starts again.
To resume normal playback press REPEAT A-B again.
“ Off” appears on the screen.
A B
NOTES:
• Some discs may not work with the repeat operation.
• In Repeat A-B mode, subtitles near point A or B may not appear.
• You may not be able to set Repeat A-B, depending on the scenes of the DVD.
• Repeat A-B does not work with MP3 CD and interactive DVDs.
27
5J20301A P20-29 27 23/4/03, 1:05 PM
MARKING DESIRED SCENES
The unit stores the points that you want to watch again. You can resume playback from that scene.
Marking the Scenes
1
Press MARKER during playback.
Marker
1 T
2
3
T
T
C
C
C
/Enter/Cancel/Marker
2
Select the blank Marker using / , then press
SELECT/ENTER at the desired scene.
Marker
1 T
2
3
T
T
1 C
C
C
3 0 08 50
• Up to 3 scenes can be selected.
• Repeat this procedure to set the other 2 scenes.
/Enter/Cancel/Marker
3
Press MARKER to remove this display.
Returning to the Scenes
1
Press MARKER during playback or stop mode.
Marker
1
T
2
3
T
T
1
1
1
C
C
C
3
4
6
0
0
0
08 50
12 27
17 04
NOTES:
• The marking is cancelled when you open the disc tray or turn the power off.
• Some subtitles recorded around the marker may fail to appear.
2
Press or to select
the Marker 1-3.
/Enter/Cancel/Marker
Marker
1 T
2
3
T
T
1
1
1
C
C
C
3
4
6
0
0
0
08 50
12 27
17 04
/Enter/Cancel/Marker
3
Press SELECT/ENTER.
Playback starts from the marked scene.
To Cancel the Mark
1
Press MARKER.
2
Press or to select the Marker 1-3.
3
Press CANCEL.
28
5J20301A P20-29 28 23/4/03, 1:05 PM
CHANGING SOUNDTRACK LANGUAGE/SUBTITLES
Changing soundtrack language
You can select the language when you play a multilingual disc.
1
Press AUDIO during playback.
2/8 Fra Dolby Digital
The current soundtrack language will appear.
NOTES:
• If the desired language is not heard after pressing the SUBTITLE button several times, the language is not recorded on the disc.
• Changing soundtrack language is cancelled when you open the disc tray. The initial default language or available language will be heard if the disc is played back again.
• Changing subtitle language is cancelled when you open the disc tray or turn the power off.
• Some functions may not work on some
DVDs. You may not be able to turn subtitles on or off or change subtitles. While playing the DVD, the subtitle may change when:
- you open or close the disc tray
- you change the title.
• In some cases, the subtitle language is not changed to the selected one immediately.
5J20301A P20-29 29
2
Press AUDIO repeatedly until the desired language is selected.
1/8 Eng Dolby Digital
The on-screen display will disappear after a few seconds.
In case of video CD playback
Audio type changes as follows each time you press AUDIO.
LR
➡
L
➡
R
Subtitles
Turning the Subtitles On and Off
When playing back a disc recorded with subtitles, you can turn the subtitles on or off.
Press SUBTITLE during playback until “Off” appears.
Off
Changing the subtitle language
You can select the language when playing back a disc recorded with multi-lingual subtitles.
1
Press SUBTITLE repeatedly during playback until your desired language appears.
1/32 Eng
2
The on-screen display will disappear after a few seconds.
29
23/4/03, 1:05 PM
CHANGING ANGLES/TITLE SELECTION/DVD MENU
Changing Angles
When playing back a disc recorded with multi-angle facility, you can change the view angle.
1
Press ANGLE during playback.
The current angle will appear.
1/9
NOTES:
• Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.
• Depending on the DVD, you may not be able to select the title. Depending on the
DVD, a “title menu” may simply be called a
“menu” or “title” in the instructions supplied with the disc.
30
5J20301A P30-33 30
2
Press ANGLE repeatedly until the desired angle is selected.
Title Selection
Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.
1
Press TOP MENU during playback.
Title menu appears on the screen.
2
Press / or / to select the desired title.
3
Press SELECT/ENTER or PLAY.
The playback of the selected title will start.
DVD Menu
Some DVDs allow you to select the disc contents using the menu.
When you play back these DVDs, you can select the subtitle language and soundtrack language, etc. using the
DVD menu.
1
Press DVD MENU during playback.
The DVD menu appears on the screen.
• Press DVD MENU again to resume playback at the scene when you pressed DVD MENU.
2
Press / or / to select the desired item.
3
Press SELECT/ENTER.
The menu continues to another screen. Repeat steps 2 and 3 to set additional items if any.
23/4/03, 1:05 PM
SETTING THE ASPECT RATIO OF TV SCREEN/SETTING ON SCREEN DISPLAY
NOTE:
It is not always possible for the DVD disc to display the picture as per your preferred picture setting - for example, if you select
'4:3 Panscan', the disc may not offer this option. In this case the picture would display in whichever format the disc is capable of playing back.
Setting the aspect ratio of TV screen
You can select the aspect ratio of the picture.
1
Press SETUP/MENU in the stop mode or No Disc.
Press or to select
“Picture”, then press or
SELECT/ENTER.
Main Menu
Language
Picture
Sound
Parental
/Enter/Setup/Return
2
Press or to select
“TV Screen”, then press or SELECT/ENTER.
Picture
TV Screen
Display
4:3
On
3
Press or to select your desired screen type, then press SELECT/EN-
TER.
TV Screen
16:9
4:3
4:3
You have the following screen sizes to choose from:
16:9 Wide screen
A wide screen picture is displayed full size, although the image on the screen may be geometrically distorted in this mode because the TV screen has an aspect ratio of 4:3 not
16:9. However it is possible to connect this set to an external widescreen (16:9) TV set via the SCART socket (see
P.9).
4:3 Letterbox
When playing back a wide screen-DVD disc, it displays the wide picture with black bands at the top and bottom of screen.
4:3 Panscan
It displays the wide picture on the whole screen with left and right edges automatically cut off.
• If you want to return to the previous menu, press or
RETURN.
4
Press SETUP/MENU to remove the Menu screen.
Status on screen display
On screen display can be switched on or off when you press the buttons.
1
Press SETUP/MENU in the stop mode or No Disc.
Press or to select “Picture”, then press or
SELECT/ENTER.
2
Press
“Display”.
or to select
Picture
TV Screen
Display
4:3
On
3
Press or SELECT/EN-
TER to select “On” or “Off”.
Picture
TV Screen
Display
4:3
Off
On: On screen displays appear when you press the buttons (factory setting).
Off: On screen displays do not appear when you press any buttons.
• If you want to return to the previous menu, press or
RETURN.
4
Press SETUP/MENU to remove the Menu screen.
31
5J20301A P30-33 31 23/4/03, 1:05 PM
DYNAMIC RANGE CONTROL
DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment.
1
Press SETUP/MENU in the stop mode.
Press or to select
“Sound”.
Main Menu
Language
Picture
Sound
Parental
/Enter/Setup/Return
2
Press or SELECT/EN-
TER to select “DRC”.
Sound
DRC On
/Enter/Setup/Return
Sound
DRC Off
3
Press or SELECT/EN-
TER to select “On” or “Off”.
/Enter/Setup/Return
• If you want to return to the previous menu, press or
RETURN.
4
Press SETUP/MENU to remove the Menu screen.
NOTES:
• This function works only during playback of Dolby Digital recorded discs.
• The level of Dynamic Range Reduction may differ depending on DVD video disc.
32
5J20301A P30-33 32 23/4/03, 1:05 PM
Some discs are specified not suitable for children. Such discs can be limited not to play back with the unit.
PARENTAL CONTROL SETTING
1
Press SETUP/MENU in the stop mode.
Press or to select
“Parental”, then press or
SELECT/ENTER.
Main Menu
Language
Picture
Sound
Parental
/Enter/Setup/Return
2
Press or to select
“Parental Level”, then press
or SELECT/ENTER.
Parental
Password Off
Parental Level Off
3
Press or to select a level from Off or 1–8. Press
or SELECT/ENTER to set the selected level.
Parental Level
4
5
Off
1
2
3
/Enter/Setup/Return
• Level Off: The parental control setting does not function.
• Level 8: Almost all DVD software can be played back.
• Level 1: DVD software for adults cannot be played back.
• Select from the level 1 to level 8. The limitation will be
more severe as the level number is lower.
4
Press or to select
“Password”, then press or SELECT/ENTER.
Parental
Password Off
Parental Level 1
NOTES:
• If each setup (P.22, 31–34) has been completed, the unit can always be worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the memory when you turn the power off.
• Depending on the discs, the unit cannot limit playback.
• Some discs may not be encoded with specific rating level information though its disc jacket says “adult.” For those discs, the age restriction will not work.
5J20301A P30-33 33
5
Press number buttons (0–
9) for the password.
Don’t forget the password.
• If you input a wrong number, press CANCEL.
6
Press SELECT/ENTER to store the password.
Note: Now the rating is locked and the setting cannot be changed unless you enter the correct password.
Password
Password 1234
Parental
Password On
Parental Level 1
• If you want to return to the previous menu, press or RETURN.
7
Press SETUP/MENU to remove the parental control screen.
33
23/4/03, 1:05 PM
TO CHANGE THE PARENTAL LEVEL
1
Press SETUP/MENU in the stop mode or No Disc.
Press or to select “Parental”, then press or SE-
LECT/ENTER.
2
Press or to select
“Password”, then press or SELECT/ENTER.
Parental
Password On
Parental Level 1
3
Press number buttons (0–
9) to enter the password you have stored.
Password
Password 1234
• If you input a wrong number, press CANCEL.
4
Press SELECT/ENTER.
The password is now Off.
Parental
Password Off
Parental Level 1
NOTE:
Do not forget the password. If you forget your password, or would like to change it, you can reset the code by pressing both the DVD STOP button on the unit and the number 2 button on the remote control for approx. 3 seconds simultaneously.
Please contact the customer helpline on page 60 for details.
5
Press or to select
“Parental Level”. Then press or SELECT/EN-
TER. The Parental Level screen is displayed.
Parental
Password Off
Parental Level 1
6
Press or to select a level from Off or 1–8 and then press or SELECT/
ENTER.
Parental Level
5
6
3
4
7
8
/Enter/Setup/Return
7
Press or to select
“Password” and then press
or SELECT/ENTER.
Parental
Password Off
Parental Level 8
8
Press number buttons (0–
9) to enter a 4-digit password.
Password
Password 1234
Note: Make sure that you select a password number that you will remember easily.
9
Press SELECT/ENTER.
The parental level is now changed and locked.
Parental
Password On
Parental Level 8
• If you want to return to the previous menu, press or
RETURN.
10
Press SETUP/MENU to remove the parental control screen.
34
5J20301A P34-LAST 34 23/4/03, 1:05 PM
TEMPORARY DISABLING OF RATING LEVEL BY DVD DISC
Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set.
It is up to you to decide whether to cancel the rating level or not.
1
Load a DVD disc and press
PLAY (see page 23).
2
If the DVD disc has been designed to temporarily cancel the Rating level, the screen which appears after inserting a DVD will change, depending on which disc is played. If you select “YES” with the SELECT/ENTER key, “Your disc exceeds the parental control level.” screen will then appear.
Your disc exceeds the parental control level.
Password
____
Enter/0–9/Cancel/Return
3
If you wish to cancel the set rating level temporarily, enter the 4-digit password.
Then press SELECT/ENTER.
Alternatively, if the password has not been set, playback will commence. If you don’t know (or have forgotten) the password, select “STOP”.
The setting screen will disappear. Press OPEN/CLOSE to remove the disc.
To quit entering, press RETURN.
4
Playback will commence if the entered password was correct.
NOTE:
This temporary cancellation of rating level will be kept until the disc is ejected.
When the disc is ejected, the original rating level will be set again automatically.
35
5J20301A P34-LAST 35 23/4/03, 1:06 PM
LANGUAGE CODE LIST
Enter the appropriate code number for the initial settings "AUDIO", "SUBTITLE" and/or "MENU LANGUAGE"
(see page 22).
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919
Afar
Afrikaans
1111
1116
Finnish
French
1619
1628
Lithuanian
Macedonian
2230
2321
Slovak
Slovenian
2921
2922
Albanian
Amharic
Arabic
Armenian
2927
1123
1128
1835
Frisian
Galician
Georgian
German
1635
1722
2111
1415
Malagasy
Malay
Malayalam
Maltese
2317
2329
2322
2330
Somali
Spanish
2925
1529
Sundanese 2931
Swahili 2933
Assamese
Aymara
Azerbaijani
Bashkir
1129 Greek 1522 Maori
1135 Greenlandic 2122 Marathi
1136 Guarani
1211 Gujarati
1724
1731
Moldavian
Mongolian
Basque 1531 Hausa
Bengali; Bangla 1224 Hebrew
Bhutani
Bihari
1436
1218
Hindi
Hungarian
1811
1933
1819
1831
Nauru
Nepali
Norwegian
Oriya
2319 Swedish 2932
2328 Tagalog 3022
2325 Tajik
2324 Tamil
2411 Tatar
2415 Telugu
2425 Thai
2528 Tibetan
3017
3011
3030
3015
3018
1225
Breton
Bulgarian
1228 Icelandic
1217 Indonesian
Burmese 2335 Interlingua
Byelorussian 1215 Irish
Cambodian
Catalan
Chinese
Corsican
2123
1311
3618
1325
Italian
Japanese
Javanese
Kannada
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
1828
1329
1411
2422
Kashmiri
Kazakh
Kirghiz
Korean
1929
1924
1911
1711
Panjabi
Pashto, Pushto
Persian
Polish
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
1524 Kurdish
1525 Laothian
2131 Serbian
2225 Serbo-Croatian
1530 Latin 2211 Shona
1625 Latvian, Lettish 2232 Sindhi
2611 Tigrinya
2629 Tonga
3019
3025
1611 Turkish 3028
2622 Turkmen 3021
1930 Portuguese
2011 Quechua
2630 Twi 3033
2731 Ukrainian 3121
2033 Rhaeto-Romance 2823 Urdu
2124 Romanian 2825 Uzbek
3128
3136
2831 Vietnamese 3219
2923 Volapük 3225
2911 Welsh
1714 Wolof
2928 Xhosa
2918 Yiddish
2924 Yoruba
2914 Zulu
1335
3325
3418
2019
3525
3631
36
5J20301A P34-LAST 36 23/4/03, 1:06 PM
BEFORE REQUESTING SERVICE
If your unit does not work properly check the following before calling a service engineer.
SYMPTOMS
POWER
CAUSE
No power.
The Mains lead is not connected.
ON/STANDBY button is OFF.
TV BROADCAST RECEPTION
The Mains lead is disconnected.
No picture, no sound.
Sound OK, poor picture.
Picture OK, poor sound.
Poor reception.
Poor colour or no colour.
Aerial connector is not connected or wires are broken.
ON/STANDBY button is off.
Possibly station trouble.
Possibly station trouble.
Aerial connector is not connected or wires are broken.
Possibly local interference.
Possibly station trouble.
Possibly local interference.
Volume control set at minimum position.
Aerial connector is not connected or wires are broken.
Possibly station trouble.
Aerial connector is not connected or wires are broken.
Possibly station trouble.
Possibly local interference.
SOLUTION
Connect Mains lead to AC outlet.
Set it to ON.
Connect the Mains lead to the AC outlet.
Check aerial connections or broken wires.
Press the ON/STANDBY button.
Try another channel.
Try another channel.
Check aerial connections or broken wires.
Move the aerial away from the source of interference.
Try another channel.
Move the aerial away from the source of interference.
Increase VOLUME control.
Check aerial connections or broken wires.
Try another channel.
Check aerial connections or broken wires.
Try another channel.
Move the aerial away from the source of interference.
Adjust the colour settings.
PAGE
6
6
6
9
9
13
13
6
17
13
17
13
6
13
6
13
17
Colour control is not adjusted.
15
DVD
The playback picture has occasional distortion.
The unit does not start playback.
The disc is dirty.
It is in fast forward or fast reverse playback.
No disc is inserted.
An unplayable disc is inserted.
The disc is placed upside down.
The disc is not placed within the guide.
The disc is dirty.
The parental lock function is set.
Playback does not follow the course of the disc’s program.
It is in the mode of repeat playback, memory playback, etc.
appears on the screen.
The function is prohibited with the unit or the disc.
Eject the disc and clean it.
Some times a small amount of picture distortion may appear. This is not a malfunction.
Insert a disc.
Insert a playable disc (Check the disc type and colour system).
Place the disc with the playback side down.
Place the disc correctly inside the guide on the disc tray.
Clean the disc.
Cancel the parental lock function or change the parental lock level.
These operations may prevent a proper progress of the contents.
20
–
23
20
23
23
20
33,34
–
– –
REMOTE CONTROL
Remote control does not work.
It is not aimed at the remote sensor.
Distance too far or there is too much light in the room.
Obstacle in the path of beam.
Batteries are weak.
Polarities of the batteries, + or –, are not inserted correctly.
Aim it at the remote control sensor.
Operate within 5 metres and reduce the light of the room.
Clear the path of the beam.
Replace batteries.
Install batteries correctly.
5
5
5
5
5
NOTE: In the case that the scart input of the unit is connected to AV1 scart of a recordable equipment such as a VTR, DVD+VTR, DVD-R etc and when the input of the recordable equipment is also selected to AV1, there maybe some white flashing lines on the screen and a high pitch sound may also be heard. This is due to the feedback loop of the connections to the unit and it is not a defect of the unit.
37
5J20301A P34-LAST 37 23/4/03, 1:06 PM
SPECIFICATION
TELEVISION
Picture Tube:
Television System:
Tuner:
Receiving Channels:
Aerial Input:
Audio Output Power:
Speaker:
DVD
Signal system:
Applicable disc:
Audio characteristics:
Frequency response:
S/N Ratio:
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
Pickup:
GENERAL
Power Source:
Power Consumption:
Weight:
Dimensions:
Operating Temperature:
55 W
11.0 kg
VTD1420
14" (34 cm "V") measured diagonally
90 degree deflection
UK 625 Lines 50 Fields
PAL I
Electronic Tuner
UHF: 21 - 69
UHF 75 ohm unbalanced
1.5 W+1.5W (max)
(3.8 x 6.9 cm 8 ohm) x 2
PAL
DVD (12cm, 8cm), CD (12cm, 8cm)
DVD: 4Hz - 22KHz
CD: 4Hz - 20KHz
90dB
0.06%
Below Measurable Level
90dB
Audio : (RCA) –12.0 dBm, 1Kohm
Digital Audio : 0.5Vp-p/75 ohm
CD : Wavelength: 775 - 805 nm
Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm
Maximum output power: 1.0 mW
AC 230V~240V, 50Hz
362(W)x382(H)x365(D)mm
5
°
C to 40
°
C
VTD2020
20" (48 cm "V") measured diagonally 90 degree deflection
(7.6 cm 8 ohm) x 2
65 W
21.5 kg
489(W)x480(H)x465(D)mm
REMOTE CONTROL UNIT
Power Supply: DC 3V (Two batteries, AAA/ R03/ UM-4)
ACCESSORIES 1 Remote Control
2 Batteries (UM-4)
1 Loop Aerial
1 Remote Control
2 Batteries (UM-4)
Weight and Dimensions are approximate. Because we continually strive to improve our products we may change specifications and designs without prior notice.
J5J20301A
03/05
K
5J20301A P34-LAST 38 23/4/03, 1:06 PM
QUICK SET-UP GUIDE
MODEL VTD1420/VTD2020
Aerial Connections
Connect as follows.
Loop Aerial supplied
(VTD 1420 only)
Aerial
RF IN
Aerial socket
Mains lead
How to install the batteries
Use battery type UM-4 (AAA-Size).
1
Open the cover in direction of the arrow and take it off.
2 Install the batteries as shown below, pay attention to polarities.
3
Replace the compartment cover.
5J20307A Q-Sheet 1
1
23/4/03, 1:06 PM
Gerät einschalten
1
Press Power ( ) button. The STAND BY ( ) indicator will light up.
Power ( ) button
2
Press ON/STANDBY. The STAND BY ( ) indicator will go off.
On-screen language selection
1
Press TV/DVD to select TV mode.
2
Press SETUP/MENU.
If you press SETUP/MENU for the first time, the language setting menu will appear.
3
Press or to select the desired language.
Then press SELECT/ENTER.
LANGUAGE/SPRACHE/LANGUE
LINGUA/LENGUA
ENGLISH
DEUTSCH
FRANCAIS
ITALIANO
ESPANOL
PRESS: ▲ / ▼ / ENTER/ MENU
4
Press SETUP/MENU to return to the normal TV screen.
2
5J20307A Q-Sheet 2 23/4/03, 1:06 PM
Channel preset
Automatic tuning
1
Press TV/DVD to select TV mode.
2
Press SETUP/MENU.
Press or to select CHANNEL SETUP.
Then press SELECT/ENTER.
MENU
CHANNEL SETUP
PICTURE
AV COLOUR PAL
LANGUAGE
PRESS: ▲ / ▼ /ENTER/MENU
3
Press or to select AUTO .
CHANNEL SETUP
MANUAL
AUTO
CH ALLOCATION
PRESS: ▲ / ▼ /ENTER/MENU
4
Then press SELECT/ENTER.
The auto search starts and all channels are stored automatically, in the order that they are found. As this may not necessarily be the correct order, you can change the sequence of the channels (see page 12).
CH 10
5
Press SETUP/MENU repeatedly until normal TV screen appears.
5J20307A Q-Sheet 3
3
23/4/03, 1:06 PM
Playback
1
Press TV/DVD to select the DVD mode.
2
Press (OPEN/CLOSE) on the unit or OPEN/
CLOSE on the remote control.
The disc tray will open.
3
Place a disc onto the tray.
Hold the disc, position it with the printed label side up, align it with the guides, and place it in its proper position.
4
Press PLAY.
The disc tray closes automatically.
On the screen, “ ” changes to “ ” and then playback will commence.
• A menu screen may appear on the TV screen, if the disc has a menu feature. In this case, press the / / / or SELECT/ENTER to operate a menu feature.
5
Press STOP to end playback.
6
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press ON/STANDBY.
The disc tray closes automatically and unit turns off.
J5J20307A K
5J20307A Q-Sheet 4
4
23/4/03, 1:06 PM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project