3Com 1000BASE-T Technical information

PDF

Document

Introduction

This guide covers installation, removal and technical information for the

■

1000BASE-SX SFP Transceiver (3CSFP91)

■

1000BASE-LX SFP Transceiver (3CSFP92)

1000BASE-T SFP Transceiver (3CSFP93)

1000BASE-LH70 SFP Transceiver (3CSFP97)

Each transceiver, when installed into a 3Com Switch, provides a high-speed Gigabit Ethernet connection. They can be installed and removed with your system powered up.

SFP Transceiver

Installation Guide

1000BASE-SX (3CSFP91)

1000BASE-LX (3CSFP92)

1000BASE-T (3CSFP93)

1000BASE-LH70 (3CSFP97)

No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of

3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or expressed, including, but not limited to, the implied warranties, terms, or conditions of merchantability, satisfactory quality, and fitness for a particular purpose.

3Com may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.

3Com registered trademarks are registered in the United

States and may or may not be registered in other countries. 3Com and the 3Com logo are registered trademarks of 3Com Corporation.

All other company and product names may be trademarks of the respective companies with which they are associated.

Installation and Removal

Safety Precautions

Be sure you follow all safety precautions when you install or replace an SFP Transceiver. To avoid electric shocks and burns to yourself and damage to the equipment, read and follow these warnings:

WARNING : When the system is on:

■

Never insert a metal object such as a screwdriver or a finger with jewelry into open module slots

Do not touch any connections inside the chassis with your hands or fingers.

WARNING : Fiber Optic ports - Optical Safety.

Never look at the transmit laser while it is poweredup. Never look directly at the fiber TX port and fiber cable ends when they are powered-up.

WARNING : Use of controls or adjustments of performance or procedures other than those specified herein may result in hazardous laser emissions.

WARNING : RJ-45 Ports. These are shielded RJ-45 data sockets. They cannot be used as standard traditional telephone sockets, or to connect the unit to a traditional PBX or public telephone network.

Only connect RJ-45 data connectors, network telephony systems, or network telephones to these sockets.

Either shielded or unshielded data cables with shielded or unshielded jacks can be connected to these data sockets.

AVERTISSEMENT : Quand le systeme est allumé:

■

Ne jamais introdure d'objet métallique, tel qu' un tourne vis ou meme votre doight si vous portez un bijou dans le reserve au module.

Ne touchez aucun engrenage à l' interieur du chasis avec le doight ou la main.

AVERTISSEMENT : Ports pour fibres optiques – sécurité sur le plan optique.

Part No. DIASFP91-AAA03

Published October 2003

Ne regardez jamais le laser tant qu'il est sous tension.

Ne regardez jamais directement le port TX

(Transmission) à fibres optiques et les embouts de câbles à fibres optiques tant qu'ils sont sous tension.

AVERTISSEMENT : L'utilisation de contrôles, de réglages de performances ou de procédures autres que ceux qui sont spécifiés au sein du présent document risquent d'entraîner l'exposition à des rayonnements laser dangereux.

AVERTISSEMENT : Points d’accès RJ-45. Ceux-ci sont protégés par des prises de données. Ils ne peuvent pas être utilisés comme prises de téléphone conventionnelles standard, ni pour la connection de l’unité à un réseau téléphonique central privé ou public. Raccorder seulement connecteurs de données RJ-45, systèmes de réseaux de téléphonie ou téléphones de réseaux à ces prises.

Il est possible de raccorder des câbles protégés ou non protégés avec des jacks protégés ou non protégés à ces prises de données.

VORSICHT : Wenn das Betriebssystem angeschaltet ist:

■

Führen Sie niemals einen Metallgegenstand wie z.B. einen Schraubenzieher oder einen beringten

Finger in den offenen Modulschlitz ein.

Berühren Sie keine Verbindungen innerhalb des

Gehäuses mit Ihren Händen oder Fingern.

VORSICHT : Faseroptikanschlüsse – Optische

Sicherheit.

Niemals ein Übertragungslaser betrachten, während dieses eingeschaltet ist. Niemals direkt auf den Faser-

TX-Anschluß und auf die Faserkabelenden schauen, während diese eingeschaltet sind.

VORSICHT : Die Verwendung von Steuerelementen oder die Anpassung von Leistungen und Verfahren in anderer als der hierin genannten Weise kann zu gefährlichen Laseremissionen führen.

VORSICHT : RJ-45-Porte. Diese Porte sind geschützte

Datensteckdosen. Sie dürfen weder wie normale traditionelle Telefonsteckdosen noch für die

Verbindung der Einheit mit einem traditionellem privatem oder öffentlichem Telefonnetzwerk gebraucht werden. Nur RJ-45-Datenanscluße,

Telefonnetzsysteme or Netztelefone an diese

Steckdosen anschließen.

Entweder geschützte oder ungeschützte Buchsen dürfen an diese Datensteckdosen angeschlossen werden.

Handling SFPs

To prevent potential damage from electrostatic discharge, always observe the following when handling SFP

Transceivers:

■

Always wear an anti-static wristband connected to a suitable earth point.

Do not remove an SFP Transceiver from its packaging until you are ready to install it into a switch.

Do not touch any of the pins, connections or components of an SFP Transceiver.

Always store or transport an SFP Transceiver in antistatic packaging.

Regulatory Compliance

Laser Eye Safety: FDA 21(J) CFR, EN 60825-1/2.

Electrical Safety: EN/UL 60950

Inserting the Transceiver

The SFP Transceiver is keyed and there is only one way in which it can be installed correctly. It is not necessary to power-down your Switch.

1 Read and follow all safety precautions stated earlier in this guide.

2 Hold the transceiver so that the connector is toward you and the product label is visible. Ensure the wire release lever is closed (in the upright position). See

Figure 1.

3 Gently slide the transceiver into the SFP port until it clicks. If the transceiver does not click into place, remove it, turn it over and re-insert.

4 Remove the plastic protective cover if fitted.

5 Use an appropriate cable to connect the transceiver to a suitable device.

Product label

Temperatur e

P = P

S = S ack tatu s

On = enabled, link OK Flashing = disabled

Suitable port on host Switch

Figure 1 Inserting the Transceiver (for example purposes only, this figure shows a 1000BASE-SX SFP Transceiver)

Removing the Transceiver

It is not necessary to power-down your Switch.

1 Disconnect the cable from the transceiver.

2 Move the wire release lever downwards until it is pointing toward you.

3 Pull the wire release lever toward you to release the catch mechanism; the transceiver will then easily slide out.

Problem Solving

If you suspect a problem, carry out these steps before contacting your supplier:

■

Refer to the documentation supplied with your Switch for general problem solving information.

Ensure that you have followed the installation instructions in this guide, and the transceiver is correctly installed in the Switch.

Ensure that the Switch in which the transceiver is fitted

■

■ is powered-up.

Ensure that the device at the far end of the link is powered-up and operating correctly.

Ensure that all connectors on the fiber optic segment are correctly engaged (1000BASE-SX, 1000BASE-LX,

1000BASE-LH70 SFP Transceivers only).

Clean the fiber terminators by wiping them gently with a clean tissue or cotton bud moistened with a little ethanol. Dirty fiber terminators on the fiber optic segment impair the quality of the light transmitted through the cable (1000BASE-SX, 1000BASE-LX,

1000BASE-LH70 SFP Transceivers only).

To remove an LH70 SFP Transceiver that has been inserted with the wire release lever pointing down, push the blue plastic at the base of the transceiver inwards towards the unit to release the catch mechanism.

For information about obtaining technical support, refer to "Technical Support" in this guide.

Technical Specifications

1000BASE-LH70, 1000BASE-SX, 1000BASE-LX SFP Transceivers

The 1000BASE-LH70 SFP Transceiver supports a direct connection to single-mode fiber-optic cable, the 1000BASE-SX SFP Transceiver supports a direct connection to multi-mode fiber-optic cable and the 1000BASE-LX SFP Transceiver supports a direct connection to both. Table 1 shows the ranges for each connection.

Table 1 Transmission Ranges

Fiber Type

1000BASE-SX

Multimode

10000BASE-LX

Multimode

Single-mode

1000BASE-LH70

Single-mode

Diameter

(microns)

62.5

9 core

Modal

Bandwidth

(MHz • km)

160

200

400

500

400

500

Minimum

Connector

End Polish

Transmission Range

2 m - 220 m (6.6 ft - 721.8 ft)

2 m - 275 m (6.6 ft - 902.3 ft)

2 m - 500 m (6.6 ft - 1640.5 ft)

2 m - 550 m (6.6 ft - 1804.6 ft)

2 m - 10,000 m (6.6 ft - 32,810 ft)

2 m - 70 km (6.6 ft - 43 miles)

Table 2 shows the optical characteristics for the transmitter and receiver for each Transceiver.

CAUTION: If using cable lengths shorter than 25 km with the 1000BASE-LH70 SFP Transceiver, you must ensure that a single-mode fiber attenuator is used to avoid signal saturation.

Table 2 Optical Characteristics

Parameter

Transmitter:

Output Optical Power

(Average)

Receiver:

Optical Input Power

Transmitter:

Output Optical Power

(Average)

Receiver:

Optical Input Power

Transmitter:

Output Optical Power

(Average)

Receiver:

Optical Input Power

Symbol

Pout

Minimum

-9.5

-17

9.5

-20

-24

Typical Maximum

-6.5

-3

Unit dBm dBm dBm dBm dBm dBm

1000BASE-T SFP Transceiver

The 1000BASE-T SFP Transceiver port uses Category 5 copper cabling with RJ-45 connectors, and supports segment lengths of up to 100 m (328 ft), as specified in the Gigabit Ethernet standard

IEEE802.3-2000.

CE Statement (Europe)

This product complies with the European Low Voltage Directive 73/23/EEC and the EMC Directive

89/336/EEC as amended by European Directive 93/68/EEC.

Technical Support

To obtain telephone support as part of your warranty and other service benefits, you must first register your product at http://eSupport.3com.com/

The following options are available for technical support:

■

Contact your network supplier.

Check the 3Com knowledgebase at

■ http://knowledgebase.3com.com

Browse the 3Com web site at http://www.3com.com

Please have your product model name, part number and serial number (found on underside of transceiver) along with all relevant details of the problem to hand before calling your network supplier or 3Com.

Telephone numbers are correct at the time of publication.

Find a current directory of support telephone numbers posted on the 3Com web site at http:// csoweb4.3com.com/contactus/.

Country

Asia, Pacific Rim

Telephone Number

Australia

Hong Kong

India

Indonesia

Japan

Malaysia

New Zealand

Pakistan

Philippines

P.R. of China

Singapore

S. Korea

Taiwan

Thailand

1 800 678 515

800 933 486

+61 2 9424 5179 or

000800 650 1111

001 803 61009

00531 616 439 or

03 5977 7991

1800 801 777

0800 446 398

+61 2 9937 5083

1235 61 266 2602 or

1800 1 888 9469

10800 61 00137 or

021 6350 1590 or

00800 0638 3266

800 6161 463

080 333 3308

00801 611 261

001 800 611 2000

You can also obtain support in this region using the following e-mail: [email protected]

Or request a repair authorization number (RMA) by fax using this number: + 65 543 6348

Europe, Middle East, and Africa

From anywhere in these regions, call:

+44 (0)1442 435529

From the following countries, you may use the numbers shown:

Austria

Belgium

Denmark

Finland

France

Germany

Hungary

Ireland

Israel

Italy

Luxembourg

Netherlands

Norway

Poland

Portugal

South Africa

Spain

Sweden

Switzerland

U.K.

01 7956 7124

070 700 770

7010 7289

01080 2783

0825 809 622

01805 404 747

06800 12813

01407 3387

1800 945 3794

199 161346

342 0808128

0900 777 7737

815 33 047

00800 441 1357

707 200 123

0800 995 014

9 021 60455

07711 14453

08488 50112

0870 909 3266

You can also obtain support in this region using the following URL: http://emea.3com.com/support/ email.html

Country Telephone Number

Latin America

Antigua

Argentina

Aruba

Bahamas

Barbados

Belize

Bermuda

Bonaire

Brazil

Cayman

Chile

Colombia

Costa Rica

Curacao

Ecuador

Dominican Republic

Guatemala

Haiti

Honduras

Jamaica

Martinique

Mexico

Nicaragua

Panama

Paraguay

Peru

Puerto Rico

Salvador

Trinidad and Tobago

Uruguay

Venezuela

Virgin Islands

1 800 988 2112

0 810 444 3COM

1 800 998 2112

52 5 201 0010

1 800 998 2112

0800 13 3COM

1 800 998 2112

AT&T +800 998 2112

1 800 998 2112

AT&T +800 998 2112

57 1 657 0888

AT&T +800 998 2112

1 800 998 2112

571 657 0888

01 800 849CARE

AT&T +800 998 2112

54 11 4894 1888

AT&T +800 998 2112

1 800 998 2112

AT&T +800 998 2112

1 800 998 2112

AT&T +800 998 2112

57 1 657 0888

You can also obtain support in this region using the following:

Spanish speakers, enter the URL: http://lat.3com.com/lat/support/form.html

Portuguese speakers, enter the URL: http://lat.3com.com/br/support/form.html

English speakers in Latin America should send e-mail to: [email protected]

North America & Canada 1 800 876 3266

Register Your Product

To take advantage of warranty and other service benefits, you must first register your product at http:// eSupport.3com.com/ . 3Com eSupport services are based on accounts that you create or have authorization to access. First time users must apply for a user name and password that provides access to a number of eSupport features including Product Registration, Repair Services, and Service Request.

3Com Corporation , Corporate Headquarters

350 Campus Drive,

Marlborough, MA 01752-3064

To learn more about 3Com products and services, visit our

Word Wide Web site at www.3com.com.

All specifications subject to change without notice.

Hello! I am an AI chatbot specifically trained to assist you with the 3com 1000BASE-T Datasheet. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!