Beckhoff CB6263 Manual
Reklama
Reklama
Manual for computer board
CB6263
Version:
Date:
0.2
17.07.2019
Index
Index
CB6263 Version: 0.2
3
Index
4 Version: 0.2
CB6263
Documentation issue status
1 Documentation issue status
Version Comment
0.1
First preliminary version (draft)
0.2
Adaptations in the block diagram, corrected feature list, adaptation of the interface designation, adaptations in the BIOS
CB6263 Version: 0.2
5
6
Notes on the documentation
2 Notes on the documentation
This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards.
It is essential that the documentation and the following notes and explanations are followed when installing and commissioning the components.
It is the duty of the technical personnel to use the documentation published at the respective time of each installation and commissioning.
The qualified personnel must ensure that the application of the described products meets all safety requirements, including all applicable laws, specifications, regulations and standards.
Disclaimer
The documentation has been prepared with care. The products described are, however, constantly under development.
We reserve the right to revise and change the documentation at any time and without prior announcement.
No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation.
Trademarks
Beckhoff ® , TwinCAT ® , EtherCAT ® , Safety over EtherCAT ® , TwinSAFE ® , XFC ® and XTS ® are registered trademarks of and licensed by Beckhoff Automation GmbH.
Other designations used in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owners.
Patents
The EtherCAT Technology is covered, including but not limited to the following patent applications and patents:
EP1590927, EP1789857, DE102004044764, DE102007017835 with corresponding applications or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the following patent applications and patents:
EP0851348, US6167425 with corresponding applications or registrations in various other countries.
EtherCAT ® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH,
Germany
Copyright
© Beckhoff Automation GmbH & Co. KG, Germany.
The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization are prohibited.
Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design.
Version: 0.2
CB6263
Safety instructions
3 Safety instructions
Safety regulations
Please note the following safety instructions and explanations!
Product-specific safety instructions can be found on following pages or in the areas mounting, wiring, commissioning etc.
Exclusion of liability
All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.
Personnel qualification
This description is only intended for trained specialists in control, automation and drive technology who are familiar with the applicable national standards.
Description of symbols
In this documentation the following symbols are used with an accompanying safety instruction or note. The safety instructions must be read carefully and followed without fail!
DANGER
Serious risk of injury!
Failure to follow the safety instructions associated with this symbol directly endangers the life and health of persons!
WARNING
Risk of injury!
Failure to follow the safety instructions associated with this symbol endangers the life and health of persons!
CAUTION
Personal injuries!
Failure to follow the safety instructions associated with this symbol can lead to injuries to persons!
NOTE
Damage to the environment or devices
Failure to follow the instructions associated with this symbol can lead to damage to the environment or equipment.
Tip or pointer
This symbol indicates information that contributes to better understanding.
UL note
This symbol indicates important information regarding UL certification.
Intended use
The CB6263 Computer Board was designed and developed exclusively for configuration in automation processes. To that end the board is equipped with external interfaces in order to acquire or output digital or analog signals or forward them to higher-level components.
Any other use is regarded as inappropriate.
CB6263 Version: 0.2
7
Safety instructions
The specified limits for electrical and technical data must be adhered to.
8 Version: 0.2
CB6263
Overview
4 Overview
4.1
Properties
The CB6263 is conceived as a compact PC. It offers basic functions, on-board RAM and a powerful CPU of the Intel® Bay trail generation in the smallest space.
The CB6263 provides 1x DisplayPort/HDMI, 1x USB2.0, 1x USB3.0 and 2x Gigabit-LAN as I/O interfaces on its front panel.
The BAseCon140 plug enables the flexible extension of the I/O functions of the CB6263. It provides 8 PCIe lanes, of which 4 can be multiplexed with SATA signals and 4 with USB 3.0 signals. The configuration of the
I/O functions is taken care of by the PIC on the expansion card. The PIC contains the configuration data, which are communicated to the board upon connection and thus enable an uncomplicated and selfconfiguring extension of the I/O options.
Further, a Status LED shows the status of the power controller.
Despite its extremely small format, therefore, the CB6263 offers the full functionality of a motherboard.
Fig. 1: Block diagram - CB6263
CB6263 Version: 0.2
9
Overview
4.1.1
List of features
CB6263
CPU
Socket
Memory
I/O on front panel
Internal I/O
Graphic resolution
RTC
BIOS
Power supply
Format
75 x 75 Board
Intel® Atom™ E3845 (QC, 2M, 1.91 GHz), TDP 10W
Intel® Atom™ E3827 (DC, 1M, 1.75 GHz), TDP 8W
Intel® Atom™ E3815 (SC, 1M, 1.46 GHz), TDP 5W
DDR3L
Onboard DRAM-1.35V / DDR3 (depending on CPU up to 1333 MHz, up to
4 GB)
1x DisplayPort
2x LAN 10/100/1000
1 x USB 2.0
1 x USB 3.0
1x M.2 (B) sockets, signals dependent on chipset see Internal: M.2
1x BAseCon140, for signals see Internal: BAseCon140 (Q170 only)
DisplayPort1.1a: 2560 x 1600 (at 16:10), 2560 x 1440
(at 16:9)
HDMI1.4/DVI: 1920x1200 (at 16:10), 1920x1080
(at 16:9)
With external CMOS battery (via 2-pin contact strip or expansion card)
AMI ® Aptio V
20V - 30V Input voltage
Overvoltage and undervoltage protection
Reverse polarity protection
Not galvanically isolated
75 x 75 mm
Availability of the processors
The list of features lists all the processors that can be ordered. Their actual availability depends on the manufacturer.
10 Version: 0.2
CB6263
Overview
4.1.2
Specifications and documents
The following documents, specifications or webpages were used for the preparation of this manual or as further technical documentation respectively.
PCI specification
Version 2.3 or 3.0
www.pcisig.com
PCI Express® Base Specification
Version 2.0
www.pcisig.com
ACPI specification
Version 3.0
www.acpi.info
ATA/ATAPI specification
Version 7 Rev. 1 www.t13.org
USB specifications www.usb.org
SM-Bus specification
Version 2.0
www.smbus.org
Intel® chip descriptions
Intel® Atom™ Processor E3800 Product Family datasheet www.intel.com
Intel® chip description i210 datasheet www.intel.com
SMSC® chip description
SCH3114 datasheet (NDA required) www.smsc.com
American Megatrends®
Aptio™ Text Setup Environment (TSE) User Manual www.ami.com
American Megatrends®
Aptio™ 4.x Status Codes www.ami.com
CB6263 Version: 0.2
11
Detailed description
5 Detailed description
5.1
CPU
The processors employed are System-on-a-Chip models from Intel®. These SoCs are based on processors from the Atom™ E38xx family, which are characterized by very low power consumption, but nevertheless offer a contemporary performance with clock rates of currently up to 2 GHz. Despite its extremely small size and low power consumption, the processor offers a second-level cache of 256 kB per core and familiar standard features such as SSE4.1/4.2, loadable microcode, etc.
Intel® processors from the Atom™ E38xx family feature an extended ambient temperature range and are therefore particularly suitable for use in industrial systems.
5.2
Memory
Four permanently installed DRAM memory modules are used on the CB6263 board.
Depending on the component variant, these are 2GByte or 4GByte DDR3 memory variants. Depending on the CPU used, a maximum clock frequency of 1333MHz is supported.
5.3
M.2
M.2 cards can easily and simply be inserted by plugging them into the slot and fixing them with a screw.
Cards of different types have different recesses (keys). Depending on which types are supported, ports can accept expansion cards of one or more types. The M.2 socket of the CB6263 supports M.2 modules with
Key B. SATA signals that allow an SSD to be connected are output via the interface.
12 Version: 0.2
CB6263
Connections
6 Connections
6.1
Plug connector overview
The plug connections of the CB6263 board are summarized in the illustration below. The function of the respective plug connection can be taken from the table below the illustration, as can the page of the manual on which further information about this connection can be read.
Fig. 2: Front panel
Front panel
The illustration corresponds to the installation situation in the PC housing.
6.2
Number
P904
P903
P900
P905
P902
P902
P803
P800
P802
P801
List of interfaces
Function (designation)
Vin (X101)
Page
Front panel: Power supply (X101) [ } 15]
LAN 1 (X102)
Front panel: LAN (X102, X103) [ } 16]
LAN 2 (X103)
Front panel: LAN (X102, X103) [ } 16]
DisplayPort (X104)
Front panel: DisplayPort / HDMI / DVI (X104) [ } 17]
USB2.0 (X105)
Front panel: USB 2.0 (X105) [ } 18]
USB3.0 (X106)
Front panel: USB 3.0 (X106) [ } 19]
BAseCon140
M.2 socket
Fan connection housing plug
(three-pole)
RealTimeClock RTC housing plug
(two-pin)
The numbers in brackets correspond to the labeling of the external interfaces on the housing on the front panel of the Industrial PC.
CB6263 Version: 0.2
13
Connections
6.3
Note on the use of cables
Requirement for the cabling!
The cables used must meet certain requirements for most interfaces. For example, twisted and shielded cables are necessary for a reliable USB 2.0 connection. Limitations in the maximum cable length are also no rarity. All of these interface-specific requirements are to be taken from the respective specifications and observed accordingly.
14 Version: 0.2
CB6263
Connections
6.4
External connections
6.4.1
Front panel: Power supply (X101)
The connection for the power supply is implemented as a 2x2-pin housing plug. The main power supply
(24 V) for the module is on pin 3.
Fig. 3: CB6263 Vin
90° plug
As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
Pin assignment of the power plug:
Description
PC Start: Input for starting and shutting down the PC.
Low (0 V or open contact): PC starts.
Signal
PC_START 1
High (>3 V): PC shuts down.
PC Status: Output of the PC status. The voltage corresponds to the positive supply voltage and can be loaded with 1 A.
PC_ACTIVE 2
Low (0 V): PC is off.
High (Vin): PC is on.
Pin
3
4
Vin
Signal
GND
Description
24 V supply voltage
Ground
Function restrictions PC_On switch
Please note that there are system states in which the activation of a connected PC_On switch is ignored by the system, e.g. during booting of a Windows operating system.
In this case, repeat the operation of the switch after a few seconds.
The same applies to connected PC_On buttons.
CB6263 Version: 0.2
15
Connections
6.4.2
Front panel: LAN (X102, X103)
The board has two Gigabit-LAN connections. Network components compatible with 10BaseT, 100BaseT and
1000BaseT can be connected to all of them. The required speed is selected automatically. Auto-Cross and
Auto-Negotiate are available as well as PXE and RPL functionality. Controller is Intel®'s i210.
90° plug
As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
Fig. 4: CB6263 LAN
Pin assignment of LAN connector:
4
5
6
7
8
Pin
1
2
3
Name
LAN-0
LAN-0#
LAN-1
LAN-2
LAN-2#
LAN-1#
LAN-3
LAN-3#
Description
LAN line 0 +
LAN line 0 -
LAN line 1 +
LAN line 2 +
LAN line 2 -
LAN line 1 -
LAN line 3 +
LAN line 3 -
The LEDs of the LAN interfaces indicate the activity and speed of the data transmission (Mbit/s). The righthand LED lights up when there is a connection and activity, and the left-hand LED during data transmission:
Mbit/s Right LED
Permanent with connection,
Flashing during data transmission
Green
Green
Green
Left LED
Permanent during data transmission
Green
Orange
None
1000
100
10
16 Version: 0.2
CB6263
Connections
6.4.3
Front panel: DisplayPort / HDMI / DVI (X104)
An appropriate standard plug is available for devices with a DisplayPort connection.
The interface additionally provides HDMI/DVI signals that can be used with aid of an adapter. Please consult your distributor with regard to a suitable adapter.
90° plug
As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
Fig. 5:
Pin assignment of DisplayPort plug:
Description
DisplayPort Lane 0 +
DisplayPort Lane 0 -
Ground
Line 2 plus
Line 2 minus
Ground
DP / HDMI
Auxiliary plus
Auxiliary minus
Ground
Signal
L0
L#0
GND
L2
L#2
GND
HDMI#
AUX
AUX#
GND
5
7
9
1
3
11
13
15
17
19
Pin
2
4
6
8
10
12
14
16
18
20
Signal
GND
L1
L#1
GND
L3
L#3
GND
GND
HPD
3.3 V
Description
Ground
Line 1 plus
Line 1 minus
Ground
Line 3 plus
Line 3 minus
Ground
Ground
Hot Plug Detect
3.3 V supply voltage
Switching to HDMI
DisplayPort signals are led out via the interface by default. With the use of a level shifter cable the board switches the DisplayPort specification 1.1 automatically to HDMI signals.
CB6263 Version: 0.2
17
Connections
6.4.4
Front panel: USB 2.0 (X105)
The USB channel 1 is provided via a standard USB connector and supports USB specification 2.0. This USB interface can supply up to 500mA current and is electronically fused.
All necessary settings for USB are done by the BIOS. Note that the "USB mouse and keyboard" function in the BIOS setup is only required if the operating system does not offer USB support. This function should not be selected for settings in the setup and for booting Windows with a USB mouse and keyboard connected, because this would lead to considerable performance limitations.
Fig. 6: CB6263 USB 2.0
Pin assignment of USB 2.0 connector:
Pin
1
2
3
4
Name
VCC
USB D#
USB D
GND
Description
5 V for USB
Data channel USB -
Data channel USB +
Ground
18 Version: 0.2
CB6263
Connections
6.4.5
Front panel: USB 3.0 (X106)
USB channel 2 is made available via a standard USB plug connector.
This USB channel supports the USB 3.0 specification. Contrary to the specification, the USB 3.0 channel only supplies current up to 500 mA. Devices with their own current supply must be used for higher power demands. The USB interface is electronically fused.
All necessary settings for USB can be made in the BIOS. This applies to both USB interfaces. Note that the
"USB mouse and keyboard" function in the BIOS setup is only required if the operating system does not offer
USB support. This function should not be selected for settings in the setup and for booting Windows with a
USB mouse and keyboard connected, because this would lead to considerable performance limitations.
Fig. 7: CB6263 USB 3.0
Pin assignment of USB 3.0 connector:
4
5
6
7
Pin
1
2
3
8
9
Signal
VCC
D-
D+
GND
RX-
RX+
GND
TX-
TX+
Description
5 V supply voltage
Data - (USB 2.0)
Data + (USB 2.0)
Ground
Receive line - (USB 3.0)
Receive line + (USB 3.0)
Ground
Transmit line - (USB 3.0)
Transmit line + (USB 3.0)
CB6263 Version: 0.2
19
Connections
6.5
Internal connections
6.5.1
Internal: M.2 (Key B)
The CB6263 is equipped with an M.2 socket, into which an M.2-2242 card (Key B) can be inserted. SATA signals (up to 3 Gb/s), which enable the connection of an M.2-SSD card, are fed out via this socket.
Fig. 8: CB6263 M.2
Pin assignment of M.2 connector:
Description
Configuration pin
Ground
Ground
Ground
Connector Key
Configuration pin
(not led out)
(not led out)
Ground
(not led out)
Signal
CONFIG_3
GND
GND
USB Channel 2 Data + USB D+
USB Channel 2 Data - USB D-
GND
Config 0
GPIO11
DPR
GND
PER1#
USB3-5 SSRX#
SSICRX#
19
21
23
25
11
13
15
17
27
29
5
7
9
1
Pin
2
3 4
Signal
3.3V1
3.3V2
6 FCPWROFF#
8 WDISABLE#
10 GPIO9
DAS
DDS
LED1
12 Connector Key
14
16
18
20 GPIO5
22 GPIO6
24 GPIO7
26 GPIO10
28 GPIO8
30 UIM RST
20 Version: 0.2
Description
Standby supply voltage S3.3V
Standby supply voltage S3.3V
Full Card Power OFF active low
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
CB6263
Description
(not led out)
Ground
(not led out)
(not led out)
Ground
SATA Lane 1 Receive plus
SATA minus
Lane
Ground
SATA Lane 1 Transmit minus
SATA Lane 1 Transmit plus
Ground
(not led out)
(not led out)
Ground
(not led out)
(not led out)
(not led out)
(not led out)
Power good
1 Receive
Configuration pin
SATAB
PER0#
SATAB#
GND
PET0#
SATAA#
PET0
SATAA
GND
REFCLK#
REFCLK
GND
ANTCTL0
ANTCTL1
ANTCTL2
ANTCTL3
RESET#
CFG1
Signal
PER1
USB3-5 SSRX
SSICRX
GND
PET1#
USB3-5 SSTX#
SSICTX#
PET1
USB3-5 SSTX
SSICTX
GND
PER0#
Ground
Ground
Configuration pin
GND
GND
CFG2
31
Pin Signal
32 UIM CLK
33
35
37
71
73
75
49
51
53
55
57
59
61
63
65
67
69
39
41
43
45
47
34
36
38
UIM DATA
UIM PWR
DEVSLP
40 GPIO0
42 GPIO1
44 GPIO2
46 GPIO3
48 GPIO4
50 PRST#
52 CLKREQ#
54 PEWAKE#
56 N/C
58 N/C
60 COEX3
62 COEX2
64 COEX1
66 SIM DETECT
68 SUSCLK
70 3.3 V
72 3.3 V
74 3.3 V
Connections
Description
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
PCIe Reset active low
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
Suspend clock
Standby supply voltage S3.3V
Standby supply voltage S3.3V
Standby supply voltage S3.3V
CB6263 Version: 0.2
21
Connections
6.5.2
Internal: BAseCon140
The BAseCon140 plug connector (Samtec HSEC-170-01-L-DV-A-K-TR) enables the flexible extension of the
IO functions of the CB6263. It provides up to 8 PCIe lanes, of which 4 can be multiplexed with SATA2.0 (3G) signals and 4 with USB 3.0 signals. In addition, DisplayPort, HSIC, SMBus and 1Wire signals are fed out via the BAseCon plug. The extension board takes care of the configuration of the IO functions. A PIC on the expansion card contains the configuration data, which are communicated to the board upon connection and thus enable an uncomplicated and self-configuring extension of the I/O options.
Observe the current limits!
In order to avoid damaging the device, it is essential to observe the following current limits:
A maximum load of 2.8 A per pin must not be exceeded. On account of the different current consumptions of the usable processors the actual current consumption may be lower. The respective maximum values can be obtained from your distributor on inquiry.
Irrespective of the CPU in use, a maximum total load of 100 W must not be exceeded.
Fig. 9: CB6263 BAseCon140
Pin assignment of BAseCon140 connector:
Description
S UPS output
S UPS output
VCC
VCC
Ground
Ground
S VCC
Signal
S UPS OUT1
S UPS OUT2
5V1
5V2
GND
GND
S5V
Ground GND
PCIe Lane 1 Transmit
+
PE1 TX/
SATA4 TX
-
PCIe Lane 1 Transmit PE1 TX#/
SATA4 TX#
Ground GND
PCIe Clock Lane 1 + PECLK1
PCIe Clock Lane 1 PECLK1#
Ground GND
19
21
23
25
27
9
11
13
5
7
1
3
Pin
2
4
6
8
10
12
14
15
17
16
18
20
22
24
26
28
Signal
S UPS IN1
S UPS IN2
GND
GND
3.3V1
3.3V2
S3.3V
GND
SATA4 RX/
PE1 RX
SATA4 RX #/
PE1 RX#
GND
PECLK2
PECLK2#
GND
22 Version: 0.2
Description
S UPS input
S UPS input
Ground
Ground
3.3 V supply voltage
3.3 V supply voltage
Standby supply voltage 3.3 V
Ground
PCIe Lane 1 Receive
+
-
PCIe Lane 1 Receive
Ground
PCIe Clock Lane 2 +
PCIe Clock Lane 2 -
Ground
CB6263
Description
PCI Lane 2 Transmit
+
-
PCI Lane 2 Transmit
Ground
(not led out)
(not led out)
Ground
(not led out)
(not led out)
Ground
SATA Lane 2
Transmit +
SATA Lane 2
Transmit -
Ground
PCIe Clock Enable
Lane 1 active low
(not led out)
PCIe Reset active low
SMBus Clock
Signal
PE2 TX/
SATA3 TX
PE2 TX#/
SATA3 TX#
GND
PE3-TX/
SATA2-TX
PE3-TX#/
SATA2-TX#
GND
PECLK3
PECLK3#
GND
PE4-TX/
SATA1-TX
PE4-TX#/
SATA1-TX#
GND
PCKE1#
PCKE3#
PERST#
SMBCLK
SMBus Alert active low
(not led out)
SMB-Alert#
PCKE5/OC4#
(not led out)
Ground
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
PCKE7/OC2#
GND
PE5-TX/
USB3-4-TX/
USBC1-TX
PE5-TX#/
USB3-4-TX#/
USBC1_TX#
USB2-4 (GND)
PECLK5/
USBC_SBU1
(GND)
PECLK5#/
USBC-SBU2
(GND)
USB2-4#
(GND)
CB6263
71
73
75
37
39
41
43
45
47
49
29
Pin
30
31
33
35
32
34
36
38
40
42
44
46
48
50
65
67
69
51
53
55
57
59
61
60
KEY
62
63 64
52
54
56
58
66
68
70
77
79
72
74
76
78
80
Signal
SATA3 RX/
PE2 RX
SATA3 RX #/
PE2 RX#
GND
SATA2 RX/
PE3 RX
SATA2 RX#/
PE3 RX#
GND
PECLK4
PECLK4#
GND
SATA1 RX/
PE4 RX
SATA1 RX #/
PE4 RX #
GND
PCKE2#
PCKE4#
PEWAKE#
SMBDAT
1Wire
PCKE6#/
OC3#
PCKE8#/
OC1#
GND
USBC1 RX/
USB3-4 RX/
PE5 RX
USBC1 RX#/
USB3-4 RX#/
PE5 RX#
USB2-8
(GND)
PECLK6
(GND)
PECLK6#
(GND)
USB2-8 D#
(GND)
Version: 0.2
Connections
Description
PCIe Lane 2 Receive
-
PCIe Lane 2 Receive
Ground
(not led out)
(not led out)
Ground
(not led out)
(not led out)
Ground
SATA Lane 2
Receive +
SATA Lane 2
Receive -
Ground
PCIe Lane 2 Clock
Enable active low
(not led out)
PCIe Wake active low
SMBus Data
1-Wire
(not led out)
USB Overcurrent active low
Ground
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
(not led out)
23
Connections
Description
(not led out)
(not led out)
Signal
PE6-TX/
USB3-3-TX/
USBC2-TX
PE6-TX#/
USB3-3-TX#/
USBC2-TX#
GND
PE7-TX/
Ground
(not led out)
(not led out)
USB3-2-TX/
SSIC-TX
PE7-TX#/
USB3-2-TX#/
SSIC-TX#
USB 2.0 Channel 3 + USB2-2 (GND)
Ground (GND)
Ground (GND)
USB 2.0 Channel 3 USB2-2#
(not led out)
(not led out)
Ground
(GND)
PE8-TX/
USB3-1-TX
PE8-TX#/
USB3-1-TX#
GND
SATA GP1
SATA GP3
GPIO1/
SATAGP1
GPIO3/
SATAGP3/
USBC-CC1
TwinCAT LED Red GPIO5/
TCLEDR
TwinCAT LED Blue GPIO7/
TCLEDB
SATA LED active low SATA-LED
RTC Battery
Power Management
Event active low
BATT
PME#
PWRBTN# Power button active low
PSON
Ground
DP / HDMI switchover
PSON
GND
DP/DVI#
DisplayPort Hot Plug
Detect
DPHPD
Ground GND
DisplayPort Lane 0 + DPL0
24
81
83
85
87
89
91
93
95
97
Pin
82
84
86
88
90
92
94
96
98
99 100 USB3-1 RX/
PE8 RX
101 102 USB3-1 RX#/
PE8 RX#
103 104 GND
105
KEY
106 SATAGP2/
107
GPIO2
108 USB-CC2/
109
111
SATAGP4/
GPIO4
110 GPIO6/
TCLEDG
112 GPIO8
113
115
117
119
121
123
125
127
114 USBPWREN
116 PWRFAIL
118 PWRGOOD
120 MRST#
122 ATXPWRGD
124 GND
126 DDCC/
DPAUX
128 DDCD/
129
131
Version: 0.2
DPAUX#
130 GND
132 DPL1
Signal
USBC2 RX/
USB3-3 RX/
PE6 RX
USBC2 RX#/
USB3-3 RX#/
PE6 RX#
GND
SSIC RX/
USB3-2 RX/
PE7 RX
SSIC RX#/
USB3-2 RX#/
PE7 RX#
USB2-1
PECLK8
PECLK8#
USB2-1#
Description
(not led out)
(not led out)
Ground
(not led out)
(not led out)
USB 2.0 Channel 10
+
PCIe Lane 8 Clock +
PCIe Clock Lane 8 -
-
USB 2.0 Channel 10
(not led out)
(not led out)
Ground
(not led out)
(not led out)
TwinCAT LED Green
(not led out)
USB Power Enable
SUSV
Power good
Reset button active low
ATX Power good
Ground
DisplayPort Aux +/
DDC Clock
DisplayPort Aux - /
DDC Data
Ground
DisplayPort Lane 1 +
CB6263
Description Signal
DisplayPort Lane 0 DPL0#
Ground GND
DisplayPort Lane 2 + DPL2
DisplayPort Lane 2 DPL2#
133
135
137
139
Pin Signal
134 DPL1#
136 GND
138 DPL3
140 DPL3#
Connections
Description
DisplayPort Lane 1 -
Ground
DisplayPort 3 +
DisplayPort 3 -
CB6263 Version: 0.2
25
Connections
6.5.3
Internal: FAN
The CB6263 has a 3-pin fan connection (JST BM03B-SRSS-TBT(LF)-(SN)). This enables a fan with a supply voltage of 5 V to be connected directly to the module. The connection has a speed monitoring function. The connected fan must supply a corresponding tachometer signal if this is to be used.
Fig. 10: CB6263 FAN
Pin assignment of fan connector:
2
3
Pin
1
Signal
GND
5 V
TACHO
Description
Ground (PWM-controlled)
Supply voltage 5 V regulated
Fan monitoring signal
26 Version: 0.2
CB6263
Connections
6.5.4
Internal: RTC
The CB6263 can be connected to an external RTC battery via a bipolar housing plug (JST BM02B-SRSS-
TBT(LP)(SN)) to provide power to the integrated clock even if there is no power supply. The battery voltage must not exceed 3.3V.
UL conformity
All technical measures for UL conformity are already integrated on the board.
Accordingly, no additional actions are necessary for the connection of an RTC battery. The battery must be connected directly.
Fig. 11: CB6263 RTC
Synchronism of the RTC
The quartz of the RTC reacts to temperature fluctuations. Therefore, correct synchronism of the
RTC is possible only with suitable and sufficient cooling!
Pin assignment RTC battery plug:
Pin
1
2
Name
BATT
GND
Description
3.3 V battery voltage
Ground
CB6263 Version: 0.2
27
BIOS
7 BIOS
7.1
Using the setup
Within the individual setup pages the last saved settings can be restored can at any time with F2 (”Previous
Values”). Use F3 (”Optimized Defaults”) to load the factory defaults. Use F2/F3 to load the complete set of settings and F4 to save them (”Save & Exit").
A “►” sign in front of the menu item indicates that a submenu is available. Use the arrow keys to navigate between menu items. Use the Enter key to select menu items and call submenus or selection dialogs.
For each setup option a help text is displayed at the top right, which in many cases contains useful information about the option and permitted values, etc.
Note on Setup Documentation
The BIOS is regularly updated so that the available setup options can change at any time without notice. This may result in differences between the options actually available and those described below. It should also be noted that the settings shown in the setup menus below are not necessarily the recommended or default settings. Which settings must be selected depends on the application scenario in which the board is operated.
28 Version: 0.2
CB6263
BIOS
7.2
Main CB6263
Board Information
Board CB6263
Revision 1
Bios Version 0.78
Processor Information
BayTrail SoC D0 Stepping
Brand String Intel® Atom™ CPU [email protected]
Max CPU Speed 1740 MHz
CPU Signature 30679
Processor Cores 2
Microcode Patch 90a
Memory Information
Total Memory 8192 MB (LPDDR3L)
System Date [Sun 12/05/2018]
System Time 00:47:04]
Setup entry
Board
Revision
Bios version
Processor Information
BayTrail SoC
Brand String
Max CPU Speed
CPU Signature
Processor Cores
Microcode Patch
Memory Information
Total Memory
System Date
System Time
Set the Date. Use Tab to switch between Date elements.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Option
None
None
None
None
None
None
None
None
None
None
The system date can be set here.
The system time can be set here.
CB6263 Version: 0.2
29
BIOS
7.3
Advanced
Power Supply Type [ATX]
PCI RT32 Service [Disabled]
► ACPI Settings
► Hardware Monitor
► CPU Configuration
► PPM Configuration
► SATA Configuration
► Miscellaneous Configuration
► Network Stack Configuration
► Power Controller Options
BAseCon Configuration
► CSM Configuration
► USB Configuration
► Security Configuration
Intel® Ethernet Connection i210 Gigabit
Intel® Ethernet Connection i210 Gigabit
► Driver Health
Setup entry
Power-Supply Type
ACPI Settings
Hardware Monitor
CPU Configuration
PPM Configuration
SATA Configuration
Miscellaneous Configuration
Network Stack Configuration
Power Controller Options
BAseCon Configuration
CSM Configuration
USB Configuration
Intel® Ethernet Connection I210 Gigabit
Intel® Ethernet Connection I210 Gigabit
Driver Health
Select the Type of the
Power Supply: AT/ATX
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Option
ATX / AT
Submenu: ACPI Settings [ } 31]
Submenu: Hardware Monitor [ } 31]
Submenu: CPU Configuration [ } 32]
Submenu: PPM Configuration [ } 35]
Submenu: SATA Configuration [ } 36]
Submenu: Miscellaneous Configuration [ } 37]
Submenu: Network Stack [ } 38]
Submenu: Power Controller Options [ } 39]
BAseCon 1 serial number xxxxxxxxxxxxxx revision x
/ No BAseCon device found
Submenu: CSM Configuration [ } 40]
Submenu: USB Configuration [ } 41]
00:01:05:xx.xx.xx
00:01:05:xx.xx.xx
Submenu: Driver Health [ } 43]
30 Version: 0.2
CB6263
BIOS
7.3.1
ACPI Settings
ACPI Settings
Enable ACPI Auto Configuration [Enabled]
Enabled Hibernation [Enabled]
Lock Legacy Resources [Disabled]
Enables or disables BIOS
ACPI Auto Configuration.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Bios entry
ACPI Settings
Enable ACPI Auto Configuration
7.3.2
Hardware Monitor
PC Health Status
CPU dig. : +51 ‘C
MB Temp : +44 ‘C
PwrCtrlVCC : +5.20 V
Options
Disabled / Enabled
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Bios entry
PC Health Status
CPU dig.
1.0 V
VCCCORE
5 V
12 V
Memory VDD
3.3 V
Fan 1
Fan 2
MB Temp
Memory Temp
PwrCtrlTemp
Options
None
None
None
None
None
None
None
None
None
None
None
None
CB6263 Version: 0.2
31
BIOS
7.3.3
CPU Configuration
CPU Configuration
► Socket 0 CPU Information
► CPU Thermal Configuration
CPU Speed 1467 MHz
64-bit Supported
Limit CPUID Maximum [Disabled]
Execute Disabled Bit [Enabled]
Intel Virtualization Technology [Enabled]
Socket specific CPU
Information
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Bios entry
CPU Configuration
Socket 0 CPU Configuration
CPU Thermal Configuration
CPU speed
64 bit
Limit CPUID Maximum
Execute Disable Bit
Intel (VMX) Virtualization Technology
Options
Submenu: see
Socket CPU Information [ } 33]
Submenu: see
CPU Thermal Configuration [ } 34]
None
None
Enabled / Disabled
Enabled / Disabled
Disabled / Enabled
32 Version: 0.2
CB6263
BIOS
7.3.3.1
Socket CPU Information
Socket CPU Information
Intel® Atom™ CPU [email protected]
CPU Signature 30679
Microcode Patch 901
Max CPU Speed 1910 MHz
Min CPU Speed 500 MHz
Processor Cores 4
Intel HT Technology Not Supported
Intel VT-x Technology Supported
L1 Data cache 24 kB x 4
L1 Code Cache 32 kB x 4
L2 Cache 1024 kB x 2
L3 Cache Not Present
Bios entry
Socket CPU Information
CPU signature
Matchcode Patch
Min CPU Speed
Processor Cores
Intel HAT Technology
Intel VT-x Technology
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
Options
None
None
None
None
None
None
None
None
None
None
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
33
BIOS
7.3.3.2
CPU Thermal Configuration
CPU Thermal Configuration
DTS [Disabled]
Bios entry
CPU Thermal configuration
DTS
Options
Enabled / Disabled
Enable/Disabled
Digital Thermal
Sensor.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
34 Version: 0.2
CB6263
7.3.4
PPM Configuration
PPM Configuration
CPU C state Report [Enabled]
Max CPU C-state [C7]
Soix [Disabled]
Bios entry
PPM Configuration
CPU C state Report
Max CPU state Report
Soix
Options
Enabled
C7 / C6 / C1
Disabled / Enabled
BIOS
Enable/Disable CPU C state report to OS
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
35
BIOS
7.3.5
SATA Configuration
SATA Configuration
Serial-ATA (SATA) [Enabled]
SATA Test Mode [Disabled]
SATA Speed Support [Gen2]
SATA ODD Port [No ODD]
SATA Mode [AHCI Mode]
Serial-ATA Port 0 [Enabled]
SATA Port0 HotPlug [Disabled]
Serial-ATA Port 1 [Enabled]
SATA Port1 HotPlug [Disabled]
SATA Port0
Not Present
SATA Port1
Not Present
Bios entry
SATA Configuration
Serial ATA (SATA)
SATA Test Mode
SATA Speed Report
SATA ODD Port
SATA Mode
Serial-ATA Port 0
SATA Port 0 HotPlug
Serial-ATA Port 1
SATA Port 1 HotPlug
SATA Port0
Not Present
SATA Port1
Not Present
Options
Enabled / Disabled
Enabled / Disabled
Gen2
No ODD
AHCI Mode
Enabled
Disabled
Enabled
Disabled
Enable or disable SATA
Device.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
36 Version: 0.2
CB6263
7.3.6
Miscellaneous Configuration
Miscellaneous Configuration
High Precision Timer [Enabled]
Boot Timer with HPET Timer [Disabled]
PCI Express Dynamic Clock Gating [Disabled]
OS Selection [Windows 7]
Bios entry
Miscellaneous Configuration
High Precision Timer
Boot Timer with HPET Timer
PCI Express Dynamic Clock Gating
OS Selection
Options
Enabled / Disabled
Disabled / Enabled
Disabled / Enabled
Windows 7
BIOS
Enable or disable
SATA Device.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous
Values
F3: Optimized
Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
37
BIOS
7.3.7
Network Stack
Network Stack
Ipv4 PXE Support [Enabled]
Ipv6 PXE Support [Enabled]
PXE boot wait time 0
Media detect count 1
Bios entry
Network stack
Ipv4 PXE Support
Ipv6 PXE Support
PXE boot wait time
Media detect count
Options
Disabled / Enabled
Disabled / Enabled
Disabled / Enabled
0..5
None
Enable/Disable
UEFI network stack
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous
Values
F3: Optimized
Values
F4: Save&Exit
ESC: Exit
38 Version: 0.2
CB6263
7.3.8
Power Controller Options
Bootloader Version 1.01-00
Firmware Version 1.02-00
Mainboard Serial No 000000000
Mainboard Prod. Date (Week.Year) 0.0
Mainboard BootCount 231
Mainboard Operation Time 237326min (3955h)
Voltage (Min/Max) 5.00V/5.10V
Temperature (Min/Max) -11’C/92’C
WDT OSBoot Timeout [Disabled]
BIOS
Select Power line for external USB devices, if powered-on
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Bios entry
Bootloader version
Firmware version
Mainboard serial no
Mainboard Prod. Date (Week.Year)
Mainboard BootCount
Mainboard operation time
Voltage (Min/Max)
Temperature (Min/Max)
WDT OSBoot Timeout
Options
None
None
None
None
None
None
None
None
Disabled
CB6263 Version: 0.2
39
BIOS
7.3.9
CSM Configuration
Compatibility Support Module Configuration Enable/Disable CSM
Support.
CSM Support [Enabled]
CSM16 Module Version 07.80
GateA20 Active [Upon Request]
Option ROM Messages [Force BIOS]
INT19 Trap Response [Immediate]
Boot option filter [UEFI and Legacy]
Option ROM execution
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Network [Legacy]
Storage [Legacy]
Video [Legacy]
Other PCI devices [UEFI]
Bios entry
Compatibility Support Module Configuration
CSM support
CSM 16 Module Version
Gate A20 Active
Option ROM Messages
Int19 Trap Response
Boot option filler
Option ROM execution
Network
Storage
Video
Other PCI devices
Options
Enabled / Disabled
None
Upon Request / Always
Force BIOS / Keep Current
Immediate / Postponed
UEFI and Legacy / Legacy only / UEFI only
Do not launch / UEFI / Legacy
Do not launch / UEFI / Legacy
Do not launch / UEFI / Legacy
Do not launch / UEFI / Legacy
40 Version: 0.2
CB6263
7.3.10
USB Configuration
USB Configuration
USB Module Version 19
USB Devices:
1 Keyboard, 2 Hubs
Legacy USB Support [Enabled]
XHCI Hand-off [Enabled]
USB Mass Storage Driver Support [Enabled]
Port 60/64 Emulation [Enabled]
USB hardware delays and time-outs:
USB transfer time-out [20 sec]
Device reset time-out [20 sec]
Device power-up delay [Auto]
Bios entry
USB Configuration
USB Module Version
USB Controllers
USB Devices
Legacy USB support
XHCI Hand-off
USB Mass Storage Driver Support
Port 60/64 Emulation
USB hardware delays and time-outs:
USB transfer time-out
Device reset time-out
Device power-up delay
Options
None
None
None
Enabled / Disabled / Auto
Enabled / Disabled
Enabled / disabled
Enabled / Disabled
1 / 5 / 10 / 20 sec
10 / 20 / 30 / 40 sec
Auto / Manual
BIOS
Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
41
BIOS
7.3.11
Security Configuration
Intel® TXE Configuration
TXE [Enabled]
TXE HMRFPO [Disabled]
TXE Firmware Update [Enabled]
TXE EOP Message [Enabled]
TXE Unconfiguration Peform
Bios entry
Intel® TXE Configuration
TXE
TXE HMRFPO
TXE Firmware Update
TXE EOP Message
TXE Unconfiguration Peform
Options
Enabled / Disabled
Disabled / Enabled
Enabled / Disabled
Enabled / Disabled
None
Send EOP Message before Enter OS
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
42 Version: 0.2
CB6263
7.3.12
Driver Health
►Intel® Pro/100 Open Source 8.3.10 PCI-E Healthy
BIOS
Provides Health Status for the Drivers/Controllers
Setup entry
►Intel(R) PRO/1000 Open Source 8.3.10 PCI-E
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
Submenu see: Intel® PRO/1000 Open Source 8.3.10
CB6263 Version: 0.2
43
BIOS
7.3.12.1
Intel® PRO/1000 Open Source 8.3.10 PCI-E
Controller 78c30018 Child 0 Healthy
Intel® I210 Gigabit Healthy
Controller 78c30118 Child 0 Healthy
Intel® I210 Gigabit Healthy
Controller 78c30458 Child 0 Healthy
Intel® I210 Gigabit Healthy
Provides Health Status for the Drivers/Controllers
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Setup entry
Controller <Address> Child 0
Intel® I210 Gigabit
Controller <Address> Child 0
Intel® I210 Gigabit
Controller <Address> Child 0
Intel® I210 Gigabit
Options
None
None
None
None
None
None
Controller address
The <address> is assigned dynamically and depends on the respective controller.
44 Version: 0.2
CB6263
BIOS
7.4
Chipset
► North Bridge
► South Bridge
North Bridge Parameters
Setup entry
North Bridge
South Bridge
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
Submenu: see North Bridge [ } 45]
Submenu: see South Bridge [ } 48]
7.4.1
North Bridge
► Intel IGD Configuration
► Graphics Power Management Control
Memory Information
Total Memory 8192 MB (LPDDR3)
Memory Slot0 8192 MB
Memory Slot1 Not Present
Max TOLUD [Dynamic]
BIOS entry
Intel IGD Configuration
Graphics Power Management Control
Total Memory
Memory slot 0
Memory slot 1
Max TOLUD
Config Intel IGD Settings.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
Submenu: see Intel IGD Configuration [ } 46]
Submenu: see Graphics Power Management Control
None
None
None
Dynamic / 1 GB / 1.25 GB / ... / 3 GB
CB6263 Version: 0.2
45
BIOS
7.4.1.1
Intel IGD Configuration
GOP Configuration
Enable GOP-driver via CSM Configuration-Video
Intel IGD Configuration
Integrated Graphics Device [Enabled]
IGD Turbo Enable [Enabled]
Primary Display [IGD]
PAVC [LITE Mode]
DVMT Pre-Allocated [64M]
DVMT Total Gfx Mem [256MB]
Aperture Size [256MB]
DOP CG [Enabled]
GTT Size [2MB]
Spread Soectrum Clock [Disabled]
ISP Enable/Disable [Enabled]
ISP PCI Device Selection [Disabled]
Vcc, Vnn Configuration for Power state2:
Vcc_Vnn Config for Power State2 [Disabled]
BIOS entry
Intel IGD Configuration
Integrated Graphics Device
IGD Turbo Enable
Primary Display
PAVC
DVMT Pre-Allocated
Aperture Size
DOP CG
GTT Size
Spread Spectrum Clock
ISP Enable/Disable
ISP PCI Device Selection
Vcc_Vnn Config Power State2
Enable: Enable
Integrated Graphics
Device (IGD) when selected as the Primary
Video Adaptor. Disable:
Always disable IGD
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
Enabled / Disabled
Enabled / Disabled
Auto / IGFX / PEG / PCI / SG
Disabled / LITE Mode / Serpent Mode
32M / 64M / 4M / 8M / 12M / 16M / 20M / 24M /
28M / 32M / 36M / 40M / ... / 60M
128MB / 256MB / 512MB / 1024MB / 2048MB
Enabled / Disabled
2MB / 4MB / 8MB
Enabled / Disabled
Enabled / Disabled
Disabled / ISP PCI Device as B0D2F0 / ISP PCI
Device as B0D3F0
Enabled / Disabled
46 Version: 0.2
CB6263
7.4.1.2
Graphics Power Management Control
Graphics Power Management Control
RC6(Render Standby) [Enable]
BIOS entry
Graphics Power Management Control
RC6 (Render Standby)
Options
Enabled / Disabled
BIOS
Check to enable render standby support.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
47
BIOS
7.4.2
South Bridge
► Azalia HD Audio
► USB Configuration
► PCI Express Configuration
High Precision Timer [Enabled]
Restore AC Power Loss [Power On]
Onboard Device Configuration
Onboard Gigabit LAN 1 [Enabled]
Onboard Gigabit LAN 2 [Enabled]
M.2-SATA Configuration Pins M.2-SATA
BIOS entry
Azalia HD Audio
USB Configuration
PCI Express Configuration
High Precision Timer
Restore AC Power Loss
Onboard Device Configuration
Onboard Gigabit LAN 1
Onboard Gigabit LAN 2
M.2-SATA Configuration Pins
Azalia HD Audio Options
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
Submenu see: Azalia HD Audio [ } 49]
Submenu see: USB Configuration [ } 50]
Submenu see: PCI Express Configuration [ } 51]
Enabled / Disabled
Power Off / Power On / Last State
Enabled / Disabled
Enabled / Disabled
None
48 Version: 0.2
CB6263
7.4.2.1
Azalia HD Audio
Audio Configuration
Audio Controller [Enabled]
Azalia VCI Enable [Enabled]
Azalia PME Enable [Enabled]
Azalia HDMI Codec [Enabled]
HDMI Port B [Enabled]
HDMI Port C [Enabled]
BIOS entry
Audio Configuration
Audio Controller
Azalia VCI Enable
Azalia PME Enabled
Azalia HDMI Enabled
HDMI Port B
HDMI Port C
Options
Enabled
Enabled / Disabled
Enabled / Disabled
Enabled / Disabled
Enabled / Disabled
Enabled / Disabled
BIOS
Control Detection of the
Azalia device. Disabled
= Azalia will be uncondtionally
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
49
BIOS
7.4.2.2
USB Configuration
USB Configuration
USB Mode [XHCI]
USB Per Port Control [Enabled]
USB Port 0 [Enabled]
USB Port 1 [Enabled]
USB Port 2 [Enabled]
USB Port 3 [Enabled]
BIOS entry
PCI Boot Configuration
USB Mode
USB Per Port Control
USB Port X
Options
XHCI / EHCI
Enabled / Disabled
Enabled / Disabled
Mode of operation of
XHCI controller
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
50 Version: 0.2
CB6263
BIOS
7.4.2.3
PCI Express Configuration
PCI Express Configuration
PCI Express Port 0 is assigned to LAN 1
PCI Express Port 1 is assigned to LAN 2
PCI Express Port 2/3 are assigned to BAseCon
PCI Express Port 2 [Enabled]
Hot Plug [Enabled]
Speed [Auto]
Extra Bus Reserved 0
Reserved Memory 10
Reserved Memory Alignment 1
Prefetchable Memory 10
Prefetchable Memory Alignment 1
Reserved I/O 4
PCI Express Port 3 [Enabled]
Hot Plug [Enabled]
Speed [Auto]
Extra Bus Reserved 0
Reserved Memory 10
Reserved Memory Alignment 1
Reserved I/O 4
BIOS entry
PCI Express Configuration
PCI Express Port 0 is assigned to LAN 1
PCI Express Port 0 is assigned to LAN 2
PCI Express Port 0 is assigned to BAseCon
PCI Express Port 2
Hot Plug
Speed
Extra Bus Reserved
Reserved Memory
Reserved Memory Alignment
Prefetchable Memory
Prefetchable Memory Alignment
Reserved I/O
PCI Express Port 3
Hot Plug
Speed
Extra Bus Reserved
Reserved Memory
Reserved Memory Alignment
Reserved I/O
Options
Enabled / Disabled
Enabled / Disabled
Auto / Gen1 / Gen2
0..7
1..20
0..31
1..20
0..31
4K / 8K / 12K / 16K / 20K
Enabled / Disabled
Enabled / Disabled
Auto / Gen1 / Gen2
0..7
1..20
0..31
4K / 8K / 12K / 16K / 20K
Enabled or Disable the PCI Express
Port 2 in the
Chipset.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous
Values
F3: Optimized
Values
F4: Save&Exit
ESC: Exit
CB6263 Version: 0.2
51
BIOS
7.5
Security
Password Description
Minimum length 3
Maximum length 20
Administrator Password
► Secure Boot menu
BIOS entry
Password Description
Minimum Length
Maximum Length
Administrator Password
Secure Boot menu
Set Administrator Password
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
None
None
An administrator password can be set here.
Submenu see: Secure Boot [ } 53]
52 Version: 0.2
CB6263
BIOS
7.5.1
Secure Boot
System Mode User
Secure Boot Not Active
Vendor Keys Active
Attempt Secure Boot [Enabled]
Secure Boot Mode [Standard]
► Key Management
BIOS entry
System Mode
Secure Boot
Vendor Keys
Attempt Secure Boot
Secure Boot Mode
Key Management
Secure Boot mode selector:
Standard/Custom.
In Custom mode Secure Boot
Variables can be configured without authentication
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3:Optimized Values
F4: Save&Exit
ESC: Exit
Options
None
None
None
Enabled / Disabled / Enabled
Standard / Custom
Submenu see: Key Management [ } 54]
CB6263 Version: 0.2
53
BIOS
7.5.1.1
Key Management
Provision Factory Defaults [Disabled]
► Reset to Setup Mode
► Enroll Efi Image
► Save all Secure Boot variables
Secure Boot variable | Size| Keys#| Key Score
► Platform Key(PK) | 862| 1| Test(AMI)
► Key Exchange Keys | 1560| 1| Default
► Authorized Signatures | 3143| 2| Default
► Forbidden Signatures | 3724| 77| Default
► Authorized TimeStamps | 0| 0| No Key
► OsRecovery Signatures | 0| 0| No Key
Commission Factory Defaults
Reset to Setup Mode
Enroll Efi Image
Save all Secure Boot variables
Platform Key(PK)
Key Exchange Keys
Authorized Signatures
Forbidden Signatures
Authorized TimeStamps
OsRecovery Signatures
Disabled / Enabled
Press enter key
Press enter key
Press enter key
Press enter key
Press enter key
Press enter key
Press enter key
Press enter key
Press enter key
Allow to provision factory default Secure
Boot keys when System is in Setup Mode
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3:Optimized Values
F4: Save&Exit
ESC: Exit
54 Version: 0.2
CB6263
BIOS
7.6
Boot
Boot Configuration
Setup Prompt Timeout 5
Bootup NumLock State [On]
Full Screen Logo [Enabled]
Fast Boot [Enabled]
VGA Support [EFI Driver]
USB Support [Partial Initial]
PS2 Devices Support [Enabled]
NetWork Stack Driver Support [Disabled]
Boot mode select [Legacy]
FIXED BOOT ORDER Priorities
Boot Option #1 [Hard Disk]
Boot Option #2 [CD/DVD]
Boot Option #3 [USB Hard Disk]
Boot Option #4 [USB CD/DVD]
Boot Option #5 [USB Key]
Boot Option #6 [USB Floppy]
Boot Option #7 [Network]
► Advanced Fixed Boot Order Parameters
BIOS entry
PCI Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
F7 Boot Menu
Full Screen Logo
Fast boot
New Boot Option Policy
StartUpDelay for UEFI shell
Boot mode select
Fixed Boot Order Priorities
Boot Option #1-19
Advanced Fixed Boot Order Parameters
Number of 1/10 sec. to wait for setup activation key. 0 means no wait.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
Options
0..65535
On / Off
Disabled / Enabled
Disabled / Enabled
Disabled / Enabled
Default / Place First / Place Last
0..255
Legacy / UEFI / Dual
Here you can set the order of the boot media to be used
Submenu see: Advanced Fixed Boot Order
CB6263 Version: 0.2
55
BIOS
7.6.1
Advanced Fixed Boot Order Parameters
Max. Cfast/SSD capacity (GB) 200
Max. USB Stick capacity (GB) 64
Capacity limit for boot group Cfast/SSD in GB
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3:
Optimized Values
F4: Save&Exit
ESC: Exit
BIOS entry
PCI Boot Configuration
Max. CFast/SSD capacity
Max. USB Stick capacity (GB)
Options
1..16384
1..16384
56 Version: 0.2
CB6263
7.7
Save&Exit
Save Changes and Reset
Discard Changes and Reset
Restore Optimized Defaults
Boot Override
► Reset System with ME disable ModeMEUD000
Bios entry
Save Changes and Reset
Discard Changes and Reset
Restore Optimized Defaults
Options
Press enter key
Press enter key
Reset the system after saving the changes.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Values
F4: Save&Exit
ESC: Exit
BIOS
CB6263 Version: 0.2
57
BIOS
7.8
BIOS update
The "DecdFlsh" program and a bootable medium with the latest BIOS version are used if the BIOS needs to be updated. When doing this it is important to start the program from a DOS environment without a virtual memory manager such as "EMM386.EXE". If such a memory manager is loaded, the program will abort with an error message or cause a crash.
DecdFlsh is a program for the automatic updating of the BIOS on all boards with AMI-BIOS. All files contained in the zip file must be unpacked into a directory, from where
DecdFlsh Bios-Dateiname calling takes place. The name of the BIOS file and its length are checked. The BIOS will now be programmed. DecdFlsh also exists as a UEFI tool for calling from the UEFI shell.
A running Flash procedure must never be interrupted, as otherwise the BIOS on the board will be destroyed.
The Flash procedure takes about 75 seconds. The necessary firmware update takes place automatically.
Avoid damage due to incorrect update execution!
If the BIOS update is performed incorrectly, the board may become unusable. Therefore a BIOS update should only be done if the corrections / additions that the new BIOS version brings with it are really needed.
Before a planned BIOS update, it is essential to ensure that the BIOS file to be reloaded is really released for exactly this board and for exactly this board version. If an inappropriate file is used, the board will inevitably not boot afterwards.
58 Version: 0.2
CB6263
8
Mechanical drawings
Mechanical drawings
Dimensional notation
All dimensions are in mil (1 mil = 0.0254 mm). Data in square brackets are in mm.
8.1
PCB: Holes
110.00
2.79
1045.80
26.56
2734.00
69.44
596.20
15.14
596.20
15.14
H5
H6
H1
1084.80
27.55
1455.00
36.96
H4
H2 H3
H7 H8
1205.20
30.61
1144.00
29.06
343.00
8.71
0/0
2651.90
67.36
dimension mil[mm]
H1-H3 (M1.5mm): drill= 1.8mm
outer diameter= 3mm
H4 (M3mm screw nut for M.2 Socket):drill 4.8mm: outer diameter= 6.5mm
H5-H8 (M2.5mm): drill= 2.7mm
outer diameter= 4.5mm
2025.00
51.43
Fig. 12: Holes CB6263
CB6263 Version: 0.2
59
Mechanical drawings
8.2
PCB: Dimensions
2952.90
75
0/0
Fig. 13: Dimensions CB6263
2952.90
75 dimension = mil [mm]
60 Version: 0.2
CB6263
Technical data
9 Technical data
9.1
Electrical data
Power supply
Board
RTC
Power consumption
RTC
24 V (+/- 5%)
>= 3 µA
<= 10 µA
9.2
Environmental conditions
Temperature range
Operating 0 °C to +60 °C (extended temperature range on request)
-25°C to +85°C
-25 °C to +85 °C, for packed boards
Storage
Dispatch
Temperature changes
Operating
Storage
Dispatch
0.5 °C per minute, 7.5 °C in 30 minutes
1.0 °C per minute
1.0 °C per minute, for packed boards
Relative humidity
Operating
Storage
Dispatch
Impact
Operating
Storage
Dispatch
Vibrations
Operating
5% to 85% (non-condensing)
5% to 95% (non-condensing)
5% to 100% (non-condensing), for packed boards
150 m/s², 6 ms
400 m/s², 6 ms
400 m/s², 6 ms, for packed boards
Storage
Dispatch
10 to 58 Hz, amplitude 0.075 mm
58 to 500 Hz, 10 m/s²
5 to 9 Hz, amplitude 3.5 mm
9 to 500 Hz, 10 m/s²
5 to 9 Hz, amplitude 3.5 mm
9 to 500 Hz, 10 m/s², for packed boards
Note on impact and vibration resistance
The specifications for impact and vibration resistance refer only to the motherboard itself without heat sink, memory module, cabling, etc.
CB6263 Version: 0.2
61
Technical data
9.3
Thermal specifications
The board is specified for an ambient temperature range of 0 °C to +60 °C (extended temperature range on request). In addition, care must be taken that the temperature of the processor die does not exceed 110 °C.
To ensure this a suitable cooling concept must be implemented that is oriented to the maximum power consumption of the processor/chipset. It must also be ensured that any existing controllers are included in the cooling concept. The power consumption of these blocks may be of the same order of magnitude as the power consumption of the processor.
The board is prepared with suitable holes for the use of modern cooling solutions. We have a series of compatible cooling components in our range. Your distributor will be pleased to assist you in selecting suitable solutions.
NOTE
Prevent the maximum die temperature being exceeded!
It is the end customer's responsibility to ensure that the die temperature of the processor does not exceed
110 °C! Continuous overheating can destroy the board!
If the temperature exceeds 110 °C, the ambient temperature needs to be reduced. Ensure sufficient air circulation if necessary.
62 Version: 0.2
CB6263
Support and Service
10 Support and Service
10.1
Beckhoff Support
Beckhoff Support offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with other, wide-ranging services:
• world-wide support
• design, programming and commissioning of complex automation systems
• extensive training program for Beckhoff system components.
Hotline: +49(0)5246/963-157
Fax: +49(0)5246/963-9157
E-mail: [email protected]
10.2
Beckhoff Service
The Beckhoff Service Center supports you in all matters of after-sales service:
• on-site service
• repair service
• spare parts service
• hotline service
Hotline: +49(0)5246/963-460
Fax: +49(0)5246/963-479
E-mail: [email protected]
10.3
Beckhoff headquarters
Beckhoff Automation GmbH & Co. KG
Hülshorstweg 20
33415 Verl
Germany
Phone: +49(0)5246/963-0
Fax: +49(0)5246/963-198
E-mail: [email protected]
Web: www.beckhoff.de
Further Support and Service addresses can be found on our website at http://www.beckhoff.de.
You will also find further documentation for Beckhoff components there.
CB6263 Version: 0.2
63
Appendix I: Post Codes
11 Appendix I: Post Codes
During the boot phase, the BIOS generates a series of status messages (so-called "POST Codes"), which can be output with the help of a suitable reading device (POST Code card). The meanings of the POST
Codes are explained in the document "Aptio™ 5.x Status Codes" from American Megatrends®, which is available from the website http://www.ami.com
. In addition, the following OEM POST Codes are output:
Code
87h
88h
89h
Description
BIOS-API started
PCA9535 started
PWRCTRL firmware update started
64 Version: 0.2
CB6263
Appendix II: Resources
12 Appendix II: Resources
12.1
Interrupt
The resources used are independent of the setup setting. The listed interrupts and their use are given by the
AT compatibility. Exclusivity on the PCI side is neither given nor possible.
Address
IRQ0
IRQ1
IRQ2(8)
IRQ3
IRQ4
IRQ5
IRQ14
IRQ15
IRQ16
IRQ17
IRQ18
IRQ19
IRQ20
IRQ21
IRQ22
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
Function
Timer
RTC
SMBus Controller
FPU
PCI Bridge(0-1) x1(x1)
PCI Bridge(0-2) x1(x1)
PCI Bridge(0-3) x1(x1)
PCI Bridge(0-4) x0(x1)
High Def Audio
CB6263 Version: 0.2
65
Appendix II: Resources
12.2
PCI devices
The PCI devices listed here all exist on the board, including those that are detected and configured by the
BIOS. Due to the BIOS setup settings it may be the case that various PCI devices or functions of devices are not activated. If devices are deactivated, the bus numbers of other devices may change as a result.
A
A
-
B
C
D
A
A
A
B
A
A
-
INT
-
-
-
-
-
-
-
-
-
-
-
-
-
REQ
0
0
0
0
1
2
0
0
0
0
0
0
Bus Dev.
Fct.
Controller / Slot
0 0 0 Host Bridge ID0F00h
2
19
0
0
VGA Controller ID0F31h
SATA (AHCI 1.0) ID0F23h
20
27
28
28
28
28
31
31
0
0
0
0
0
1
2
3
0
3
0
0
XHCI Controller ID0F35h
HD Audio ID0F04h
PCI Express Port 1 ID0F48h
PCI Express Port 2 ID0F4Ah
PCI Express Port 3 ID0F4ch
PCI Express Port 4 ID0F4Eh
ISA Bridge ID0F1Ch
SMBus Interface ID0F12h
Ethernet Controller 1xID1533h
Ethernet Controller 1xID1533h
66 Version: 0.2
CB6263
Appendix II: Resources
12.3
SMB devices
The following table lists the reserved SM-Bus device addresses in 8-bit notation.
NOTE
These address ranges may not be used by external devices even if the component assigned in the table doesn't exist on the motherboard.
Address
34-35
36-39
5C-5D
70-73
88-89
92-93
A0-A7
B0-B3
B8-BB
Function
API access to power supply unit
Reserved
NCT7491
POST Code output
Slave address defined by BIOS
I210 default
Reserved for DDR
Power controller (access via BIOS-API)
Power controller (access via BIOS-API)
CB6263 Version: 0.2
67
Preuzimanje
Javni link je ažuriran
Javni link do vašeg ćaskanja je ažuriran. You may view and manage your chat links after registration here.
Javni link dokumenta
Reklama
