StarLine STAR-E66-2 CAN-Bus Alarmsystem mit WFS, TAG (2x) Installation Manual

E96 BT, E96, E66 BT, E66 Connection diagram
For cars with a САN/LIN-bus make a connection via the digital CAN/LIN-bus, for other cars make
an analogue connection.
Information on connection to the CAN/LIN-bus of different cars is available on website can.starline.ru
Storage battery
Bluetooth antenna
Recommendations for accommodation
The main unit should be installed at a distance of at least 10
cm from the metal surfaces, in order to avoid deterioration of
reception quality of the Bluetooth and 868 MHz antennas
X1
X1
X2
X3
X4
X5
or
Security status output (200 mA) (–)
Door opening simulation output (200 mA) (–)
Engine blocking (200 mA) (–)
“Comfort” function output (200 mA) (–)
Engine operation monitoring input
Ignition input (+)
Bypass module control output (200 mA) (–)
Parking brake input (–)
Control output for code relay StarLine R4 (200 mA) (–)
Trunk limit switch input (–)
Horn control output (2 A) (+)
Brake pedal input
Trunk unlocking output (200 mA) (–)
Door input (+/–)
Door two-step unlocking output (200 mA) (–)
Hood limit switch input (–)
violet
+12 V
Temperature sensor
87а
87
Enter the program using the service code given on the owner’s plastic card.
X2
The developer and manufacturer, StarLine SPA, reserves the right to make technical
improvements not shown in this diagram.
Information on updates, current versions of operation and installation manuals are available on
the website www.starline.ru in section “Catalogue”. Charts of mounting on different car
models are available on website install.starline.ru
NC
86
(+)
NO
Ignition 1
Autostart connection diagrams for E96
Power module
To connector
X2
30
To the yellow
wire of
connector X1
86
(+)
30 А
command
«Open»
(–)
87а
87
orange-white
gray
orange
white
brown
blue-black
brown-white
green-black
white-black
orange-black
blue
black-yellow
yellow
orange
green
red
For convenient setting, diagnostics and software update use the StarLine Master program,
available for download on the website help.starline.ru/slm
Common
(–)
85
868 MHz antenna
87
85
After completing the installation of the complex, be sure to
set the current date and time from the remote (see short
user manual).
USB-connector
85
30
Blocking relay
in the set
10 А
Other possible connection
options are available on the
website www.starline.ru
Service button with LED
(–)
Unit power supply
87а
red
black
black-white
yellow-white
black-red
green-yellow
gray-black
yellow
pink
blue-red
yellow-orange
orange-white
gray
orange-violet
yellow-black
blue-black
yellow-red
orange-gray
blue
green
3А
30
+ 12 V
command
«Close»
CAN-H B
86
LIN1
(+)
CAN-L B
LIN2
CAN-L A
Output to alternative light signal control (200 mA) (–)
CAN-H A
Output to alternative central lock control (200 mA) (–)
StarLine Bus core bus
DVR control output (2А) (+)
Output to accessories (200 мА) (–)
Output to starter (200 мА) (–)
Output to ignition 1 (200 мА) (–)
Control output of the built-in starter lock (200 мА) (–)
Output to ignition 2 (200 мА) (–)
Output +12В (500 мА) (+)
Ignition lock
Ignition 2
Ignition 1
Accessories
Starter
+12 V
Activators are
connected in parallel
StarLine BP-03, BP-05
1А
+12 V
Variant 1
General installation specifications
or
Connection diagram for StarLine R4 code relay
The complex is designed for installation on vehicles with a voltage of 12V onboard power supply.
orange-gray
Before the complex installation, make sure that the circuits of the electrical equipment of the vehicle, to which the
complex is connected, are in good working order, and also in the absence of error indication of the vehicle's factory
equipment.
First of all, you should connect the "ground" wire of the complex to chassis ground.
Wiring should be made as far as possible from sources of electrical interference: ignition coils, high-voltage wires, etc.
Pay attention to the fact that the wires do not come in contact with the moving parts of the vehicle's construction pedals, steering rods, etc.
The complex installation should be carried out only by specially trained qualified installers.
When configuration the complex the parameters to be set must not contradict the requirements of the vehicle
guide.
violet-yellow
brown
black-white
NC
COM
Hood lock
UNLOCK
not used
EXT
orange
+12 V
black
GND
red
BAT
Power
black-yellow
Power supply to the components of the complex is allowed only after the installation is completed.
Do not install the engine temperature sensor near the exhaust manifold, as this may cause the sensor to overheat
and malfunction.
StarLine BP-06
To connector X1 yellow-orange wire
Hood limit switch
Blocked circuit
The complex installation should be carried out in accordance with the connection diagram.
NO
INPUT
Variant 2
External blocking relay
Ignition
blue
yellow
IGN
(-)
LOCK
85
87
(+)
green
gray
OUTPUT
86
30
NC
Common
Blocked circuit
E96 BT, E96, E66 BT, E66
Additional connection options
Setting of the security-telematic complex
Diagram of starting circuit connection on cars with “Start-Stop” button
Version 2.7
ATTENTION! The tags included in the delivery set are already registered in the main unit and are in the transport mode, i.e. off.
Pressing of the tag button in this mode will be indicated by a green and red flashes of the built-in LED. Prior to operation, press
the tag button several times until the flash color changes to green.
1. In the Starline Master application, reprogram the blue wire of connector Х4 for simulation of the brake pedal,
and the black-yellow wire of connector Х4 — for the “Start-Stop” button
2. Make connection in accordance with the diagram
Registration of new components
Lamp of stop signals
Do not connect
Do not connect
30 A
Do not connect
Do not connect
+ 12 V
ATTENTION! At registration of new tags and smartphones all previous tags and smartphones will be deleted from memory.
It will be necessary to register them again. In total, up to 5 devices can be registered in the complex.
When new remote keys are registered, all previous remote keys will be deleted from the memory. It will be necessary to
register them again. In total, up to 4 remote keys can be registered in the complex.
+ 12 V
blue
black-yellow
yellow
Do not connect
Brake limit switch
orange
green
red
To the blue wire
of connector Х4
Standard engine
To the black-yellow start and stop
wire of connector X4
button
Do not connect
Do not connect
Do not connect
START
STOP
Do not connect
EN
GINE
Starting module
Negative control pulse
Standard connection diagram for underhood unit StarLine R6
(only for E96BT/E66BT)
1. Deactivate complex security. Switch off ignition if it is on.
2. Disconnect the ВАТ, OUTPUT and INPUT wires from the car circuits.
3. Press the service button 7 times.
4. Switch on the ignition.
5. 7 light signals of the LED on the service button will follow.
6. Then 2 signals of the LED on the service button will follow, meaning entry in the registration mode.
7. Interconnect the OUTPUT and INPUT wires of the underhood unit.
8. Supply power (ВАТ and GND wires).
9. In 10 seconds, successful registration will be confirmed by 2 signals of the LED on the service button.
10. Disconnect the ВАТ wire from the car circuits, then open the OUTPUT and INPUT wires.
11. Switch off ignition and check unit operation.
Blocked circuit
NO
UNLOCK
LOCK
black
red
Temperature
sensor R6
white
GND
Power
20 А
black-yellow
red
Hood lock
drive
do not connect
EXT
orange
black
COM
Exit from the device registration mode
16. In 10 seconds switch off ignition to exit the registration mode. Light signals on the service button will follow, the number of
which will match the total number of registered tags, pendants and smartphones.
* The list of supported smartphones is available on the website www.starline.ru
Brown
Black-and-white
NC
Smartphone registration
15. Register a smartphone* using the free StarLine mobile application.
Hood limit
switch
INPUT
blue
BAT
yellow
IGN
gray
OUTPUT
Ignition
green
The device is manufactured with textual or color marking of wires.
Remote key registration
7. Press the remote key buttons 1 and 2 shortly.
8. In 3 seconds, successful registration will be confirmed by a short sound signal of the remote key and 2 light signals on the
service button. If the remote key was not registered, 4 sound signals of the remote key will follow.
9. Perform item 7-8 for each remote key.
Tag registration
10. Remove the battery from the tag.
11. Press the tag button and install the battery back. The tag LED will light up red.
12. Release the button, a series of red flashes will follow.
13. In 10 seconds, successful registration will be confirmed by a green flash and 2 signals of the LED on the service button.
If the tag was not registered, the LED will light up red.
14. Repeat items 10-12 for the remaining tags.
If unit StarLine R6 was purchased separately, it must be registered in the main unit’s memory:
orange-gray
Entry in the device registration mode
1. Deactivate complex security.
2. Switch off ignition if it is on.
3. Press the service button 7 times.
4. Switch on the ignition.
5. 7 light signals of the LED on the service button will follow.
6. Then 2 short light signals of the LED on the service button will follow, meaning entry in the registration mode.
Horn
Creation of owner authorization code (by means of the standard buttons)
1. Deactivate complex security.
2. Switch off ignition, if it was on, then press the service button 7 times.
3. Switch on the ignition.
4. 7 light signals of the LED on the service button will follow.
5. Then 2 short light signals on the service button will follow, meaning entry in the registration mode.
6. Enter the owner authorization code using the standard car buttons with pressing interval not more than 3 seconds. Each pressing
of the standard button will be accompanied with a single signal of the LED on the service button. The list of standard buttons
supported in the car is given on the website can.starline.ru
7. Acceptance of the owner authorization code will be confirmed by 2 signals of the LED on the service button.
8. Enter the owner authorization code again.
9. If the code is entered correctly, 2 light signals on the service button will follow. If the code is entered incorrectly, 4 short signals
will be heard, in this case repeat items 6...8.
10. Switch off ignition to exit the mode of owner authorization code recording.
11. Exit from the registration mode will be confirmed by signals of the LED on the service button: 2 short signals and the number of
signals corresponding to the total number of registered pendants, tags and smartphones.
12. Note down the created owner authorization code in the corresponding section of the user’s manual.