advertisement
Centurion Clip User Manual
Superclip Centurion
Latest Version of user manual & superclip updates are always available at: - http://www.centurionclip.com
(Incl. Superclip1 & Superclip2)
User Manual: Superclip/Centurion
17
th
April 2007
For Latest Update Centurion Clip: - V8.00
This Manual Assumes you have the latest update installed on your Superclip
Page. 1 http://www.centurionclip.com
Centurion Clip User Manual
Introduction.
Your new clip is a universal device for removing the network/SIM locks from a variety of models of mobile phones from different networks. Your new superclip is equipped with 2 types of communication protocols, Serial and USB, this is 1 of the first clips equipped with both.
.
Your Superclip will support the following phones: -
•
LG 8110, 8120, & 8130
•
LG-2G B2000, B2050, B2100, C2100, C2200, C3300, C3310, C3320, C3400, C1100, C1200, C1400,
C3100, F2100, F2300, F2400, G5600, G1500, G1600, G3100, G510, G5200, G5220, G5300, G5400,
G7070, G7100, L3100, L341i, L342i, W3000, W3100, W5200, W5220, W5300, W5400
• LG-2g Added V8.00 Centurion CG300, F1200, KG810, MG810, MG530
•
Motorola T191, V60, V66, Ti280, V300, 400, 500, 525, 600, C220, V80
•
Nokia DCT3 & DCT4
•
Panasonic X60
•
Samsung E800, A1xx, A300, A400, A800, V200, Q200, S10x, S200, S300, N1xx, N5xx, R2xx, Txxx, C100
& SGH Series, E800, E810, D500, E720, E330, Z105, Z107, E530, E330
•
Sendo 3 & 5 series
•
Sharp GX10, GX15, GX20, GX25, GX29, GX30, TM100, TM150
•
Sony-Ericsson
•
V600i, Z1010,Z800, Z500 V800, V802SE, Z800i, Z1010i, Z1010c, Z500i, Z500a, Z500c, Z600 and Z608
•
F500i, K500i, K500c, K506c, K508i, K508c, K700i and K700c
•
S700i, S700c and S710a
•
VK207i
•
NEC-3g . 228, 338, 313, 616, 616v
•
Newgen C800
•
NEC 338 V4
•
Lobster unlock, 485, 575, 544
•
Total LG Unlock, incl KG800 chocolate Clip
•
LG-3g Total unlock
•
8110, 8120, 8130, 8138, 8180, 8330, 8360, 8380
•
Sony-Ericsson, CID 36/37 unlock
•
Total LG2g
With USA Update V7.20 Optional Update Activated these phones are supported
•
PANTECH C300 (all versions) G700, PG1500, PG3200 not tested
•
Motorola Iden
•
Total LG2g (incl. USA Variants)
Superclip Updates by EMAIL.
You can now subscribe to our “Superclip Bulletin Service”, by registering your email address; you will receive updates direct to your mailbox as soon as they are released!!!
Please go to http://www.centurionclip.com/centurion_bulletins.html
We will also notify you when new user manuals are available, or information relating to the operation of your New Superclip.
Page. 2 http://www.centurionclip.com
Centurion Clip User Manual
Through Out This Guide Certain Terms Will Be Used To Avoid Confusion:
TARGET PHONE : “the phone being unlocked”
DEVICE: “Superclip, the unlock clip”
ADAPTOR: “cable that connects the DEVICE to the Phone connectors and to its Data Cable”
Technical Support & Help: Important Information!!!!!
Please before phoning for help or technical support check first that you have the latest update installed on your superclip!!!!!
1. Goto and download the latest updates and install them on your superclip.
2. Download the latest user manual from http://www.superclip2.com
, and check that the information you require is not in there before phoning your supplier.
Powering Your Centurion Clip
Please use a 9V PP3 Battery and the supplied cable to power your Centurion Clip
**********************************************************************************************************
Connecting Centurion Clip to Your PC Via USB
If your Centurion Clip has no software in it (lights will flash up and down randomly)
To connect your super clip to your pc:
1) Plug in 9V power
2) Plug in USB lead
3) LED 1 should be lit
**********************************************************************************************************
If your Super Clip has software in it (steady Lit LEDs)
To connect your super clip to your pc:
1) Plug in USB lead
2) Plug in 9V power within 2 seconds of plugging in the USB lead
3) LED 1 should be lit
**********************************************************************************************************
Page. 3 http://www.centurionclip.com
Centurion Clip User Manual
Unlocking Phones, Mode Guide
Please read the specific instructions for each type of phone, it is very important to follow instructions to the letter.
Points to remember when using your Superclip !!!
1. Always power your clip with a descent Battery; failure to do so could result in your clip failing during unlocking.
2. Always make sure the target phone you are unlocking has a full charge; damage can result if the phone fails during unlocking.
3. Always remove the SIM card from the phone. (Unless otherwise instructed)
4. Never interrupt the connection between the Superclip and the target phone during unlocking; damage to the target phone could result.
5. Never attempt to unlock a phone without checking the user manual for specific instructions for that model .
6. Check regularly for new updates and instructions from http://www.centurionclip.com
LED Phone Mode Table
Before unlocking a phone with the superclip, you must select the correct mode, the mode of the superclip is displayed by the state of it’s 4 LEDs, you simply press the “Select” button to change the Superclip’s mode.
NEVER ATTEMP TO UNLOCK A PHONE WITH OUT READING FULLY THE SPECIFIC INSTRUCTIONS FOR THAT MODEL !!!!
CLIP MODE LED-1 LED-2 LED-3 LED-4
Nokia DCT3 Unlock
Nokia DCT4 Unlock
Nokia DCT4 Security Code Reset
Total Sony Ericsson CID36
Samsung A1XX, A3XX, A4XX Unlock
Samsung A800 Unlock
Samsung Q/V/SXXX, P4XX, E710 Unlock
Samsung E700, E800, SGHx600 Unlock
Samsung C100 Unlock
Samsung E720
Samsung E330
Samsung Z105, Z107
Sharp GX-1, GX-10, GX10i Unlock
Sharp GX20 Unlock
Sharp GX30 Unlock
Panasonic X60 Unlock
Sharp
GX15, GX17, GX25, GX29
Sendo Unlock
LG 8110, 8120, 8130 etc. Unlock
Motorola P2k (V60, V66, V70 & Ti280 etc.) Unlock
Motorola V220, V80 Unlock
VK207, VK530
NEC-3g
Lobster, 485, 575, 544
Total LG 2G: - Group 1, Group 2, Group 3
Total LG 2G: - Group 4, Group 5 cg300, f1200, kg810, mg810, mg530 unlock
MOTOROLA IDEN
Pantech C300
LG 8180, 8330
Removed from V8.00 (install v7.90 to use the following)
Benq-Siemens E61 on on on on off off off off on blinking off blinking blinking blinking blinking blinking off off off on off off off on on off on blinking off off off on off on on off off on on off on off off off off on on off
Blinking Blinking Off blinking on off on blinking off on on on blinking blinking blinking blinking off on blinking blinking on on off off off on on off on on
Blinking
Blinking
Blinking on
Blinking
Blinking on
Blinking off
Blinking
Blinking on
Blinking on blinking off off on
Off
Off on off on off off on on off on off on off on off on off on on on off on on
Off on off on
Page. 4 http://www.centurionclip.com
Centurion Clip User Manual
USA
Optional
Update
Only
Requires
Activation
Pantech C300
Models: Pantech C300, G700, PG1500, PG3200 not tested
Clip Firmware V7.80 or V7.90
LED Sequence: Blink, Blink, Blink, On
Phone:
Connector
Powered Off
C300 Pantech
1. Switch on the Superclip and select Pantech
2. Connect up the phone. (No SIM, Battery removed)
3. Press “Enter” button.
4. Insert Battery into phone
5. Wait for Superclip’s LEDs to return to mode indication.
Motorola Iden
Models:
Clip Firmware
850, i450, R9 & R8: i355, i605, i710, i530, i530, i305, i833, i835, i415, i275, i860, i860 Woody, i860 Tattoo, i830, i830 Roxy, i730, i285, i215, i205, i305, i530, i710, i325, i315, i600, i390, i370, i1000, i1000plus, i500plus, i700plus, i2000plus, r750plus, iX1000, i550plus, i2000, i85s, i50sx, i55sr, i80s, i90c, i85s, i80s, i30sx, i35s, i95cl, i60c, i90c, i88s...ect
V7.80 or V7.90
LED Sequence: Blink, On, On, Off
Phone: Powered Off
Connector Motorola Iden
1. Switch on the Superclip and select IDEN
2. Connect up the phone. (No SIM, Powered ON)
3. Press “Enter” button.
4. Wait for Superclip’s LEDs to return to mode indication.
Page. 5 http://www.centurionclip.com
Centurion Clip User Manual
Total LG 2g Unlock
Models:
Clip Firmware
LED Sequence:
Phone:
Connector
Models:
Group 1, Group 2, Group 3
V7.80 or V7.90
Off, On, On, Off
Powered Off
PS2, LG cables, 510, 7050 & KG 800
Clip Firmware
Group 4, Group 5
V7.80 or V7.90
LED Sequence:
Phone:
Off, On, On, On
Powered Off
Connector PS2, LG cables, 510, 7050 & KG 800
LG 2g GSM phones are grouped into 5 separate groups for unlocking
Each Group as it’s stage on LG Total Unlock Mode on the Superclip
Stage Identification: - (count the stages)
•
Waiting for ignition: - slow alternating between 2 & 3
•
About to change to next stage: - Fast alternating between 2 & 3
The Clip will run through the stages when you select LG total 1 or LG Total 2 and press the enter button.
Stage 1 a
Group 1
Stage 1b
Group 2
Stage 1c
Group 3
Stage 2a
Group 4
Stage 2b
Group 5
KG220 LG-CG225
LG-F7200
LG-Cg300
LG-F1200
LG-Kg810
LG-Mg810
LG-Mg530
LG-MG155
LG-KG800
LG-KG320
LG-ME591
LG-G7120
LG-F2250
LG-F3000
LG-MG100
LG-ME500
LG-KG210
LG-KG225
LG-CE500
LG-MG105
LG-M6100
LG-C1500
LG-MG200
LG-M6100
LG-MG105
LG-A7110
LG-A7150
LG-B2070
LG-B2150
LG-B2250
LG-C1150
LG-C1300i
LG1300i
LG-C3380
LG-L1400
LG-F9100
LG-M4410
LG-MG191
LG-P7200
LG-S5000
LG-S5200
LG-F2200
LG-G7200
LG-L1200
LG-L342i
LG-L341
LG-F2400
LG-B2100
LG-C2100
LG-C3320
LG-F2100
LG-F2300
LG-F7250
LG-C3300
LG-C3310
LG-C3400
LG-B2000
LG-B2050
LG-L5100
LG-L3100
LG-C2200
LG-L1100
LG-B1200
LG-B1300
LG-C1100
LG-C1200
LG-C1400
LG-G510
LG-G1500
LG-G1600
LG-W3000
LG-GW3100
LG-C3100
LG-G4010
LG-G4050
LG-GW5200
LG-GW5220
LG-GW5300
LG-GW5310
LG-GW5400
LG-G5500
LG-G7000
LG-G7020
LG-G7030
LG-G7050
LG-G7070
LG-G7100
LG-G7120
KG800 C1300
C2000
Ce500
LG7110
F7250
F9100
VX5200
C2000
G4010
G7020
G4011
G4020
G4050
C1500
AX5000
G5500
G7000
G7030
G7050
L1100
L1400
L5100
T5100
(usa models)
1. Switch on the Superclip and select Total LG 1 or Total LG 2 (depending on model)
2. Connect up the phone. (No SIM, Powered OFF)
3. Press “Enter” button.
4. Wait for correct LG mode/stage for the target phone on the Superclip
5. Press “Power” button and hold on phone.
6. Wait for Superclip’s LEDs to return to mode indication.
Factory Reset
If the phone is still locked then power on phone and enter 2945#*# select factory reset
Page. 6 http://www.centurionclip.com
Centurion Clip User Manual
LG 2g CG300, F1200, KG810, MG810, MG530 Unlock
Models: CG300, F1200, KG810, MG810, MG530
Clip Firmware Centurion V8.00
LED Sequence: Blink, Blink, Blink, Off
Phone: Powered Off
Connector PS2, LG
1. Switch on the Superclip and select Blink, Blink, Blink, Off
2. Connect up the phone. (No SIM, Powered OFF)
3. Press “Enter” button.
4. Press “Power” button and hold on phone.
5. Wait for Superclip’s LEDs to return to mode indication.
Factory Reset
If the phone is still locked then power on phone and enter 2945#*# select factory reset
Page. 7 http://www.centurionclip.com
Centurion Clip User Manual
LG 8180 8330 Unlock
Models: LG 8180, 8330 all versions
Clip Firmware V7.80 or V7.90
LED Sequence: Off, On, Off, On
Phone:
Connector
Powered Off
PS2, LG8110 Connector
1. Switch on the Superclip and select LG
2. Connect up the phone. (No SIM, Powered OFF)
3. Press “Enter” button.
4. Press “Power” button on phone.
5. Wait for Superclip’s LEDs to return to mode indication.
LG 8110, 8120, 8130, 8138 Unlock
Models:
Clip Firmware
LG 8110, 8120, 8130, 8138 all versions
V7.80 or V7.90
LED Sequence: Off, On, Off, On,
Phone: Powered Off
Connector PS2, LG8110 Connector
1. Switch on the Superclip and select LG
2. Connect up the phone. (No SIM, Powered OFF)
3. Press “Enter” button.
4. Press “Power” button on phone.
5. Wait for Superclip’s LEDs to return to mode indication.
Page. 8 http://www.centurionclip.com
Centurion Clip User Manual
Lobster Unlock Procedure
Models:
Clip Firmware
Lobster, 485, 575, 544
V7.80 or V7.90
LED Sequence: On, Off, Off, Off
Phone: Powered Off
Connector PS2, Lobster Connector (3 types 485, 575, 544)
Lobster phones are grouped into 2 separate groups for unlocking
Each Group as it’s stage on Lobster Unlock Mode on the Superclip
Stage identification: - (count the stages)
•
Waiting for ignition:- slow alternating between 2 & 3
•
About to change to next stage:- Fast alternating between 2 & 3
The Clip will run through the stages when you select LOBSTER and press the enter button.
Stage 1 / Group 1 Stage 2 / Group 2
485, 575 544
1. Switch on the Superclip and select Lobster
2. Connect up the phone. (No SIM, Powered OFF)
3. Press “Enter” button.
4. Press “Power” button on phone.
5. Wait for Superclip’s LEDs to return to mode indication.
Phone unlocked.
NEC-3g incl. 338 V4
NEC-3g Unlock
Models: 228, 338, 313, 616 & 616v (338 V4 supported)
LED Sequence: Blinking, Blinking, On, On
Clip Firmware V7.80 or V7.90
Phone: Powered on
Connector PS2, GX-30 connecter
1. Switch the Superclip on and select NEC-3G mode
2. Ensure the Target phone is Powered On with no SIM
3. Connect to the Superclip.
4. Press the “Enter” button.
5. Wait for NEC to power down
Page. 9 http://www.centurionclip.com
Centurion Clip User Manual
Total Sony Ericsson CID 36/37
Total Sony Ericsson Unlock
Models:
LED Sequence:
•
W800
•
K600i, K608i, K300, K300i,K500, K750i,D750, D750i
•
J300i/J300a/J300c, J200,J200i,J200
•
V600i, Z1010,Z800, Z500 V800, V802SE, Z800i, Z1010i, Z1010c, Z500i, Z500a,
Z500c, Z600 and Z608
•
F500i, K500i, K500c, K506c, K508i, K508c, K700i and K700c
•
S700i, S700c and S710a
Off, On , Off, On ,
Clip Firmware V7.80 or 7.90
Phone: Powered Off (Fully Charged Battery)
Connector PS2, Ericsson connector, K750 connector.
Always turn Sony Ericsson phones on before unlocking (especially K700i) new handsets are not fully calibrated until the first time they are switched on after being flashed in the factory
(new handsets will display “please wait” and a progress bar) if you unlock the phone before calibration is complete you will need to re-flash the phone.
Phones with older style SE connection
1. Switch on the Superclip and select Total Sony-Ericsson
2. Connect up the phone. (No SIM, Powered Off)
3. Press the “Enter” button
4. Wait for Superclip’s LEDs to return to mode indication
If LEDS 1 and 4 Flash at end of the process complete the following with out turning the phone on
1. Remove phone battery
3. Press "Enter" button
4. Insert battery into phone
5. Wait for all 4 LEDs on, then wait for LED 1 before removing phone.
Phones with newer style K750 SE connection
1. Switch on the Superclip and select Total Sony-Ericsson
2. Connect up the phone. (No SIM, Powered Off)
3. Press the “Enter” button
4. When Superclip LEDS blink power on the phone
5. Wait for Superclip’s LEDs to return to mode indication
If LEDS 1 and 4 Flash at end of the process complete the following with out turning the phone on
1. Remove phone battery
3. Press "Enter" button
4. Insert battery into phone
5. Wait for all 4 LEDs on, then wait for LED 1 before removing phone.
(some may require the process twice, new phones always insert sim and allow to log onto network before unlocking)
Tips & Tricks
You can check, the CID version on most SE phones by entering the service menu
You the following key sequence (where > means menu right, < means menu left)
>*<<*<*
(CID 49 not supported)
Page. 10 http://www.centurionclip.com
Centurion Clip User Manual
Nokia Unlock
Unlocking Nokia DCT-3 Phones
Models:
LED
Sequence:
See List Here
Off, Off, Off, On
P hone: Powered On
1. Switch on the Superclip and select Nokia DCT3
2. Connect the phone (no SIM powered on)
3. Press "ENTER" button.
4. Wait for Superclips LEDs to return to mode indication
5. Phone
Note: If unlock fails switch phone on after connecting to the superclip, as soon as the phones backlights come on press the “Enter” button on the Superclip.
Unlocking Nokia DCT-4 Phones
Models:
LED
Sequence:
See List
Off, Off,
Here
On, Off
P hone: Powered On
1. Switch on the Superclip and select Nokia DCT4
2. Connect the phone (no SIM powered on)
3. Press "ENTER" button.
4. Wait for Superclips LEDs to return to mode indication
5. Phone
Reset Security Code Nokia DCT-4 Phones
Models: See List Here
LED
Sequence:
Off, Off, On, On
P hone: Powered On
1. Switch on the Superclip and select Nokia DCT4 Security Code Reset
2. Connect the phone (no SIM powered on)
3. Press "ENTER" button.
4. Wait for Superclips LEDs to return to mode indication
5. Security Code Reset To Factory Default (1234)
The following phones are BB5 not DCT4 and can not be unlocked:-
6270, 6280, 6630, 6680, 6681, 6682, 7370, N70, N71, N90, E60, E61, E70, N80, N91, N92
Nokia DCT-3 Phones
The previous generation of Nokia Phones to those currently marketed by Nokia. This list is not comprehensive
2100 - NAM-2 3210 - NSE-8 3310 - NHM-5
3330 - NHM-6
5110 - NSE-1
5210 - NPM-5
6210 - NPE-3
8250 - HSM-3D
3390 - NPB-1
5130 - NSK-1
6150 - NSM-1
7110 - NSE-5
8290 - NSB-7
3410 - NHM-2
5190 - NSB-1
6190 - NSB-3
8210 - NSM-3
8850 - NSM-2
Page. 11 http://www.centurionclip.com
Centurion Clip User Manual
8890 - NSB-6 9210 - RAE-3N
Nokia DCT-4 Phones
The latest and current generation of phones from Nokia.
This list is not comprehensive .
3320 - NPC-1 3360 - NPW-1 3510 - NHM-8
3510i - RH9 3590 - NPM-8 3650 - NHL-8
5100 - NPM-6
6310i - NPL-1
6510 - NPM-9
6800 - NHL-6
7650 - NHL-2
8910 - NHM-4
6100 - NPL-2
6340 - RH13
6590i - NSM-9
7210 - NHL-4
8310 - NHM-7
8910i - NHM-4NX
6310 - NPE-4
6360 - NPW-2
6610 - NHL-4U
7250 - NHL-4J
8390 - NSB-8
6600-
7600 7610 N-Gage
N-Gage-QD 5140 6820
Nokia Connector Compatibility Chart,
Not all Nokia phones have a unique connector, please use the chart below, to check for compatible connectors.
* 1100, 1100a, 1100b, 1101, 1110, 1600, 2300, 2300a, 2600
* 1220, 1260, 2220, 3320, 3360
* 2100, 3610, 5210, 8210, 8250, 8290, 8850, 8855, 8890
* 2112, 3100, 3100b, 3108, 3120, 6100, 6108
* 2280
* 2650, 2651
* 3200, 3200b, 6200, 6220, 6610, 6610i, 7210, 7250, 7250i
Page. 12 http://www.centurionclip.com
Centurion Clip User Manual
6170
7280
7710
3230
8800
6101
6111
6060
Samsung
Samsung E800
* N-GAGE
* N-GAGE QD
The following phones are BB5 and can not be unlocked:
6270, 6280, 6630, 6680, 6681, 6682, 7370, N70, N71, N90, E60, E61, E70, N80, N91, N92
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Griffin/UFS/JAF type cable only available use with PS-2 to Griffin adaptor
Models:
Connector
E800
LED Sequence: On, On, Off, On
Phone: Powered Off
PS2, E700 Connector
1. Switch on the Superclip and select Samsung E800 (Samsung E700, E800, SGHx600 option)
2. Press “Enter” button.
3. Connect the phone and press it's power button to power on.
4. Phone should go into "TAT" mode
Samsung D500 , D600 (D600e not supported)
Models: D500, D600
LED Sequence: On, On, Off, On
Phone: Powered Off
Connector PS2, D500 Connector
1. Switch on the Superclip and select Samsung E800 (Samsung E700, E800, SGHx600 option)
2. Connect the phone.
3. Press “Enter” button.
4. Power on the phone, Phone should go into "TAT" mode
Page. 13 http://www.centurionclip.com
Centurion Clip User Manual
Samsung E810
Models: E810
LED Sequence: On, On, Off, On
Phone:
Connector
Powered Off
PS2, E810 Connector
1. Switch on the Superclip and select Samsung E810 (Samsung E700, E800, SGHx600 option)
2. Connect the phone.
3. Press “Enter” button.
4. Power on the phone, Phone should go into "TAT" mode
Samsung E820
Models: E820
LED Sequence: On, On, Off, On,
Phone: Powered Off
Connector PS2, E700 Connector
1. Switch on the Superclip and select Samsung E820 (Samsung E700, E800, SGHx600 option)
2. Connect the phone.
3. Press “Enter” button.
4. Power on the phone, Phone should go into "TAT" mode
Samsung E720
Models: E720
LED Sequence: Blinking, Off, Off, Off
Phone: Powered Off
Connector PS2, E810 Connector
1. Switch on the Superclip and select Samsung E810 (Samsung E700, E800, SGHx600 option)
2. Connect the phone.
3. Press “Enter” button.
4. Power on the phone, Phone should go into "TAT" mode
Samsung E710
Models: E710
LED Sequence: On, Off, On, On
Phone:
Connector
Powered Off
PS2, E700 Connector
1. Switch on the Superclip and select Samsung E710 (Samsung Q/V/SXXX, P4XX, E710 Unlock)
2. Press “Enter” button.
3. Connect the phone (powered on)
4. 4 LEDS come on, to show success
Page. 14 http://www.centurionclip.com
Centurion Clip User Manual
Samsung E330 Code Reader
Models: E330
LED Sequence: Off, On, Off, Off
Phone: Powered Off
Connector PS2, E700 Connector
1. Switch on the Superclip and select Samsung E330
2. Connect the phone.
3. Press “Enter” button.
4. Power on the phone, Phone should go into "TAT" mode
5. Codes will be read in 1 second.
6. The clip will then warn you the code is about to be displayed (LEDs will sequence up and down, Knight Rider style)
7. All 4 LEDs will then flash the first number, there will be a 2 second gap between each number.
8. All 4 LEDs will remain on after the last number.
Read the unlock code from the phone using the clip. The superclip will then give you the code on the LEDs of the clip... All 4 LEDs will blink and tell you what number. So for number 4 all 4 LEDs will blink 4 times. For
"0" LEDs will flash 10 times.
Page. 15 http://www.centurionclip.com
Centurion Clip User Manual
Samsung S500
Models: S500
LED Sequence: On, Off, On, On
Phone: Powered On (try off if phone does not unlock)
Connector PS2, E700 Connector
1. Switch on the Superclip and select Samsung E820 (Samsung Q/V/SXXX, P4XX, E710 Unlock)
2. Connect the phone.
3. Press “Enter” button.
Samsung A800
Models: A800
LED Sequence: On, Off, On, Off
Phone:
Connector
Powered On (try off if phone does not unlock)
PS2, A300 Connector
1. Switch on the Superclip and select Samsung A800.
2. Connect the phone.
3. Power on the phone.
4. Press “Enter” button.
Samsung Z105, Z107 Code Reader
Models: Z105, Z107
LED Sequence: Blinking, Blinking, Off, Off
Powered On Phone:
Connector Original Z105 USB Cable
1. Switch on the Superclip and select Samsung Z105
2. Connect the phone.
3. Press “Enter” button.
4. Codes will be read in 1 second.
5. The clip will then warn you the code is about to be displayed (LEDs will sequence up and down, Knight Rider style)
6. All 4 LEDs will then flash the first number, there will be a 2 second gap between each number.
7. All 4 LEDs will remain on after the last number.
Read the unlock code from the phone using the clip. The superclip will then give you the code on the LEDs of the clip... All 4 LEDs will blink and tell you what number. So for number 4 all 4 LEDs will blink 4 times. For
"0" LEDs will flash 10 times.
Samsung E530
Models: E530
LED Sequence: Blinking, Off, Off, Off
Phone: Powered On
Connector PS2, E530 Connector
1. Switch on the Superclip and select Samsung E530 (Samsung E720 option)
2. Connect the phone.
3. Press “Enter” button.
Page. 16 http://www.centurionclip.com
Centurion Clip User Manual
Sharp
Sharp GX1, GX10, GX10i
Models: GX1, GX10, GX10i
LED Sequence: Blinking, Off, Off, On
Phone:
Connector
Powered On
PS2, GX10 connector (do not confuse with GX20 looks the same but wired differently)
1. Switch the Superclip on and select Sharp GX1, GX10
2. Ensure the Target phone is Powered ON.
3. Connect to the Superclip.
4. Press the “Enter” button.
5. Wait for Superclip’s LEDs to return to mode indication.
Tips & Tricks
If unlock fails try waiting for phone to say “waiting for SIM card” before pressing enter button, If that fails press enter button as soon as phone backlights come on.
Sharp GX15, GX17, GX25 , GX29
Models: GX15, GX17, GX25
LED Sequence: Blinking, Blinking, Off, Off
Phone: Powered On
Connector USB, GX15 Cable
1. Switch the Superclip on and select Sharp GX15
2. Ensure the Target phone is Powered ON
3. Connect to the Superclip
4. Press the “Enter” button
5. You will see “XXXX” on the target phone’s screen
6. After 5 seconds press 1. on the target phones keypad
7. Wait a further 5 seconds and press 99 on the phones keypad.
8. Press “Select” on the phones keypad. (Right hand button under LCD)
9. Wait 5 seconds and press number 3 on phones keypad. (you may have to press 1 to confirm)
10. Wait a further 5 seconds and press “Select” on the phones keypad (Right hand button under
LCD)
11. After 10 seconds the handset will display “Finished”
12. Wait 5 Seconds and power down the phone, using the top right button on the phones keypad, you will have to press it 3 times.
13. Wait 3 seconds and power the handset back on, and then power off.
14. You may now disconnect the phone from the Superclip.
Tips & Tricks
Some GX-15 phones do not appear to go into diag mode (display XXXX), allow the superclip to return to mode indication, then turn the GX15 off and back on, the phone should turn back on in Diag mode.
Sharp GX20 Unlocking
Models: GX20
LED Sequence: Blinking, Off, On, Off
Phone:
Connector
Powered On
PS2, GX20 Connector (different from GX10 connecter)
1. Switch the Superclip on and select Sharp GX20
2. Ensure the Target phone is Powered ON.
3. Connect to the Superclip.
4. Press the “Enter” button.
5. Wait for Superclip’s LEDs to return to mode indication.
Page. 17 http://www.centurionclip.com
Centurion Clip User Manual
Sharp GX30, TM100, TM150 Unlocking
Models: GX30, TM100, TM150
LED Sequence: Blinking, Off, On, On
Phone: Powered On
Connector PS2, GX30 Connector
1. Switch the Superclip on and select Sharp GX15
2. Ensure the Target phone is Powered ON
3. Connect to the Superclip
4. Press the “Enter” button
5. You will see “XXXX” on the target phone’s screen
6. After 5 seconds press 1. on the target phones keypad
7. Wait a further 5 seconds and press 99 on the phones keypad.
8. Press “Select” on the phones keypad. (Right hand button under LCD)
9. Wait 5 seconds and press number 3 on phones keypad.
10. Wait a further 5 seconds and press “Select” on the phones keypad (Right hand button under
LCD)
11. After 10 seconds the handset will display “Finished”
12. Wait 5 Seconds and power down the phone, using the top right button on the phones keypad, you will have to press it 3 times.
13. Wait 3 seconds and power the handset back on, and then power off.
14. You may now disconnect the phone from the Superclip
Page. 18 http://www.centurionclip.com
Centurion Clip User Manual
Panasonic
Panasonic X60 Unlock
Models: X60,
LED Sequence: Blinking, On, Off, Off
Phone: Powered On
Connector Jack Plug (labelled T191)
1. Switch on the Superclip and select Panasonic X60
2. Connect the phone (Powered ON)
3. Press “Enter” button.
4. Wait for Superclips LEDs to return to mode indication.
5. Insert incorrect SIM Card and then power on phone. (1 the phone will not accept)
6. type 52824** to open service menu
7. Enter 00000000 (8 Zero’s) into the Network Code
Panasonic X400 Unlock
Models: X400,
LED Sequence: Blinking, On, Off, Off
Phone: Powered Off
Connector Jack Plug (labelled T191)
1. Switch on the Superclip and select Panasonic X60
2. Connect the phone (Powered Off)
3. Power on the phone while pressing # and * screen stays white
4. Press “Enter” button.
5. LED 2 flashes then 3 then all, and then returns to mode indication.
Page. 19 http://www.centurionclip.com
Centurion Clip User Manual
Sendo.
Sendo Unlock
Models: M550, M551
LED Sequence: Blinking, On, Off, On
Powered On Phone:
Connector PS2, Sendo Connectors
1. Switch on the Superclip and select Sendo
2. Insure the handset is powered OFF
3. Connect the handset to the Superclip
4. Press “Enter” button on the Superclip
5. Power on the handset.
6. Wait for all 4 Superclip’s LEDs to flash.
Page. 20 http://www.centurionclip.com
Centurion Clip User Manual
Motorola
Motorola V Series Unlocking
Models: V300, V400, V500, V525, V600
LED Sequence: Blinking, Blinking, Off, Off
Phone: Powered On
Connector USB Cable Motorola V-Series Connecter
1. Switch on the Superclip and select Motorola V Series
2. Connect the phone (Powered ON) and hold the cable in the phone hard.
3. Press “Enter” button.
4. The phone will reset twice and all 4 lights will come on.
Motorola V80, V220 unlocking
Models: V80, V220
LED Sequence: Blinking, Blinking, Off, On
Phone:
Connector
Powered On
USB Cable (mini USB end)
1. Switch on the Superclip and select Motorola V80, V20
2. Connect the phone to the clip.
3. Then power on in test mode by holding down the # key and the * key at the same time then power on phone.
4. On V80 it must display transfer mode to do a successful unlock.
5. Press the “Enter” button.
6. Wait for Superclip’s LEDs to reach Blink, Blink, Blink, Blink
Tips & Tricks
Some later SW version V220 require the charge to be connected before it will unlock successfully.
Page. 21 http://www.centurionclip.com
Centurion Clip User Manual
VK-Mobile
VK Mobile Unlock
Models: VK207, VK207i, VK530, VK570
LED Sequence: Blinking, Blinking, On, Off
Phone: Powered On
Connector PS2, VK207 connecter (looks like Samsung A300)
1. Switch the Superclip on and select VK207i
2. Ensure the Target phone is Powered On with foreign SIM in (one the phone does not accept).
3. Connect to the Superclip.
4. Press the “Enter” button.
5. Clip will flash briefly , Phone Unlocked.
Tips & Tricks
If LEDs 1 & 4 blink while LED 2 stays on, this indicates communication error, open up the VK connector if Pins 1 and 2 are soldered together then cut pin 2.
The following are not available in the latest update and you must install the stated firmware on your clip to use
Benq E61
Removed from V8.00 Centurion, you must install firmware version 7.90 in order to use this
Models: Benq-Siemens E61
Clip Firmware V7.80 or V7.90
LED Sequence: Blink, Blink, Blink, Off
Phone:
Connector
Powered Off
PS2, 02-X2, M300 type
7. Switch on the Superclip and select BenQ
8. Connect up the phone. (No SIM, Powered OFF)
9. Press “Enter” button.
10. Press “Power” button and hold on phone.
11. Wait for Superclip’s LEDs to return to mode indication.
12. Phone unlocked.
Page. 22 http://www.centurionclip.com
Centurion Clip User Manual
Installing Superclip USB Drivers & Update
Software.
Before you can update your superclip, you must first download and install the necessary software and files on your PC, these are:-
1. Superclip USB drivers.
2. Superclip Update Software.
Goto the downloads page.
Click on the link to download the “Superclip USB Drivers”
When presented with the “File Download” dialogue box click on save.
Save the file to your machine, the “My Documents” folder is an ideal place, it will make the file easy to access.
Page. 23 http://www.centurionclip.com
Centurion Clip User Manual
Repeat the above for the “Superclip Update”
Now that we have download the install programs we need to install the SW.
Double click on “sc_usb_drivers.EXE” (the superclip USB driver installation program you just downloaded) follow the prompts, until you see the dialogue window telling you the installation has been successful, now click on “Finish”, you have now installed the USB drivers.
Page. 24 http://www.centurionclip.com
Centurion Clip User Manual
Now do the same for the Superclip update, double click on “sc_updater.EXE” and follow the same procedure, until you see the dialogue window telling you the installation has been successful, now click on “Finish”, you have now installed the Superclip updater.
The updater SW should appear, if the updater buttons do not change when you place your mouse over them you will need to download and install the “macromedia flash player” from the downloads page .
Then for the correct procedure to update your clip follow the relevant set of instructions below
!
If you are connecting your superclip to your PC for the first time, see the following about windows installing your superclip. Installing Your Superclip.
Page. 25 http://www.centurionclip.com
Centurion Clip User Manual
Installing The SuperClip On Your PC
After the software is installed, windows will need to install your superclip as a new USB device the first time it is connected.
When you get to the stage of connecting the clip to your PC follow this guide.
(you will only need to do this once, the first time you ever connect the superclip to your PC, or to a new PC)
**********************************************************************************************************
Connecting Centurion Clip to Your PC Via USB
If your Centurion Clip has no software in it (lights will flash up and down randomly)
To connect your super clip to your pc:
1) Plug in 9V power
2) Plug in USB lead
3) LED 1 should be lit
**********************************************************************************************************
If your Centurion Clip has software in it (steady Lit LEDs)
To connect your super clip to your pc:
1) Plug in USB lead
2) Plug in 9V power within 2 seconds of plugging in the USB lead
3) LED 1 should be lit
**********************************************************************************************************
1. When the Superclip is connected to your PC and the enter button is pressed, windows detects the new hardware (if this fails with Centurion clip try inserting the usb cable, then adding the 9v power to the clip in the next 1 to 2 seconds)
2. A “New Hardware Wizard” dialogue box will appear, leave the selection “Install the software automatically” selected, Click on Next.
Page. 26 http://www.centurionclip.com
Centurion Clip User Manual
3. Now windows will search for the USB drivers you installed and install the new superclip hardware
4.When the wizard has successfully installed the new hard ware click on “Finish”.
Page. 27 http://www.centurionclip.com
Centurion Clip User Manual
5. Windows will confirm your Superclip has been installed and is ready for use
Page. 28 http://www.centurionclip.com
Centurion Clip User Manual
Updating A Blank Clip
(flashing LEDs)
You must install USB Drivers 1 st
.
A blank clip has all 4 LEDs flashing in a fast sequence. Use the following sequence for updating a Blank Clip !!!!
1. Power up the clip by pressing the “Select” button
2. Start the Updater SW (if it is not running already) on your PC.
3. Connect the superclip to your PC, using a Type A-Male to Type A-Male USB cable.
4. All LEDs will change and LED 1 will remain on.
5. The message on the Updater SW will change from “Please Connect The
Super Clip” to “Super Clip Connected”
6. Click on the Updater Software the “Enter” button
7. The Updater SW will now update the Clip.
8. Once the clip is updated press and hold “Select” button for about 1 second to turn the superclip off
9. Disconnect from USB cable
10. The clip is now updated
**********************************************************************************************************
Connecting Centurion Clip Via USB
If your Centurion Clip has no software in it (lights will flash up and down randomly)
To connect your super clip to your pc:
1) Plug in 9V power
2) Plug in USB lead
3) LED 1 should be lit
**********************************************************************************************************
Page. 29 http://www.centurionclip.com
Centurion Clip User Manual
Updating A Loaded Superclip
(steady lit LEDs)
This is a superclip that has already previously had an update installed.
1. Make sure you have installed the latest Superclip updater installed, you can download this from www.superclip.co.uk
2. Power up the clip by pressing the “Select” button
3. Start the Updater SW (if it is not running already) on your PC
4. Connect the superclip to your PC, using a Type A-Male to Type A-Male USB cable.
5. Press and hold the “select” and “enter” buttons on the superclip, LED 1, should remain lit, LEDs 2, 3 & 4 should cycle up and down.
6. Release the buttons
7. Now press the enter button on the clip, LED 1 should now remain lit.
8. The message on the Updater SW will change from “Please Connect The
Super Clip” to “Super Clip Connected”
9. Click on the Updater Software the “Enter” button
10. The Updater SW will now update the Clip.
11. Once the clip is updated press and hold “Select” button for about 1 second to turn the superclip off
12. Disconnect from USB cable
13. The clip is now updated
**********************************************************************************************************
Connecting Centurion Clip Via USB
If your Super Clip has software in it (steady Lit LEDs)
To connect your super clip to your pc:
1) Plug in USB lead
2) Plug in 9V power within 2 seconds of plugging in the USB lead
3) LED 1 should be lit
**********************************************************************************************************
Page. 30 http://www.centurionclip.com
Centurion Clip User Manual
Updating The SuperClip Firmware
Some updates require the firmware in the superclip to be updated.
You will be advised if this is necessary when the update is released.
1. Install the New update.
2. Run the newly installed Updater.
3. Connect the Clip to computer with the USB A to A Cable.
4. Press enter on the clip and LED 1 should light.
5. Now Click on the enter button on the Software.
6. After the clip has updated.
THE NEXT PART IS VERY IMPORTANT AND MUST BE DONE RIGHT
THIS WILL ONLY HAPPEN ON THE FIRST UPDATE
UPDATING AGAIN WILL NOT UPDATE THE FIRMWARE AGAIN
7. Turn off the Clip by Holding the SELECT button for 1 secondthen releasing it.
8. Now Disconnect the clip from the USB Cable.
9. Once Disconnected Press the SELECT Button LED 1 Should Flash.
10. Press the SELECT Button Once more and now LED 4 Should Flash.
11. Now Press Enter. (Firmware is now Updated)
Page. 31 http://www.centurionclip.com
Centurion Clip User Manual
Activating Optional Updates (USA Option)
Notes about V6.10
The latest Update (v7.60 includes the USA functions but in order to use them they must be activated)
Download and Install The latest Update For your Superclip if you have not done so already,
Install the latest update for your superclip and update the firmware if required (how to update firmware guide here )
Activating USA unlock functions
1. Then have V4.00 updater running and the clip disconnect from the computer
2. Press the SELECT button on the clip until you see BLINK, BLINK, BLINK, ON
3. Then connect the clip to the computer and press ENTER on the clip.
4. LED 1 and 3 will now be lit.
5. Now click Enter on the software.
6. The Updater will now read the EID from the clip and display it in the updating window and also at bottom of
7. Clip Software.
Then email the EID code at the bottom of the software (Highlighted in RED) to your supplier.
Uploading the activation file .
Your supplier will then send you an activation file, save this file into the superclip folder on your PC
Continued on next page …………….
Page. 32 http://www.centurionclip.com
Centurion Clip User Manual
1. Then have the latest updater running and the clip disconnect from the computer
2. Press the SELECT button on the clip until you see BLINK, BLINK, BLINK, ON
3. Then connect the clip to the computer and press ENTER.
4. LED 1 and 3 will now be lit.
5. Now click Enter on the software and the software will now update the clip.
Clip Updated And Activated !!!
Note: You can not read the EID again once you have uploaded the activation file, this is normal and correct !!!
Page. 33 http://www.centurionclip.com
Centurion Clip User Manual
NEVER ATTEMP TO UNLOCK A PHONE WITH OUT READING FULLY THE SPECIFIC INSTRUCTIONS FOR THAT MODEL !!!!
CLIP MODE LED-1 LED-2 LED-3 LED-4
Nokia DCT3 Unlock
Nokia DCT4 Unlock
Nokia DCT4 Security Code Reset
Total Sony Ericsson CID36
Samsung A1XX, A3XX, A4XX Unlock
Samsung A800 Unlock
Samsung Q/V/SXXX, P4XX, E710 Unlock
Samsung E700, E800, SGHx600 Unlock
Samsung C100 Unlock
Samsung E720
Samsung E330
Samsung Z105, Z107
Sharp GX-1, GX-10, GX10i Unlock
Sharp GX20 Unlock
Sharp GX30 Unlock
Panasonic X60 Unlock
Sharp
GX15, GX17, GX25, GX29
Sendo Unlock
LG 8110, 8120, 8130 etc. Unlock
Motorola P2k (V60, V66, V70 & Ti280 etc.) Unlock
Motorola V220, V80 Unlock
VK207, VK530
NEC-3g
LG cg300, f1200, kg810, mg810, mg530 unlock
Lobster, 485, 575, 544
Total LG 2G: - Group 1, Group 2, Group 3
Total LG 2G: - Group 4, Group 5
MOTOROLA IDEN
Pantech C300
LG 8180, 8330
Removed from V8.00 (install v7.90 to use the following)
Benq-Siemens E61 on on on on off off off off on blinking off blinking blinking blinking blinking off off off on off off off on on off on blinking off off off off on on off off on on off on off off off off on on blinking on off
Blinking Blinking Off blinking on blinking on off on off on on blinking blinking blinking blinking off on blinking blinking on
Blinking Blinking blinking on off off
Blinking
Blinking on
Blinking off on on on
Blinking off
Blinking off on on on
Blinking on blinking on off on off on off on on off on on on off on on off
Off on off on on off on
Off off off on off on
Off
Off
Page. 34 http://www.centurionclip.com
advertisement