Intermec CK30 User Manual
Annonce
Annonce
Intermec Technologies Corporation
Corporate Headquarters
6001 36th Ave. W.
Everett, WA 98203
U.S.A. www.intermec.com
The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec.
Information and specifications contained in this document are subject to change without prior notice and do not represent a commitment on the part of Intermec
Technologies Corporation.
2003 by Intermec Technologies Corporation. All rights reserved.
The word Intermec, the Intermec logo, Norand, ArciTech, CrossBar, Data Collection
Browser, dcBrowser, Duratherm, EasyCoder, EasyLAN, Enterprise Wireless LAN,
EZBuilder, Fingerprint, i-gistics, INCA (under license), InterDriver, Intermec Printer
Network Manager, IRL, JANUS, LabelShop, Mobile Framework, MobileLAN,
Nor*Ware, Pen*Key, Precision Print, PrintSet, RoutePower, TE 2000, Trakker
Antares, UAP, Universal Access Point, and Virtual Wedge are either trademarks or registered trademarks of Intermec Technologies Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)
This product includes cryptographic software written by Eric Young.
Throughout this manual, trademarked names may be used. Rather than put a trademark (
or
) symbol in every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A. ii CK30 Handheld Computer User’s Manual
Contents
Contents
Before You Begin .....................................................................................................vi
Safety Summary.........................................................................................vi
Safety Icons ..............................................................................................vii
Global Services and Support .....................................................................vii
Who Should Read This Document? ..........................................................ix
Related Documents ...................................................................................ix
Patent Information ....................................................................................ix
1
Using the CK30 Handheld Computer
.................................................1
Introducing the CK30 Handheld Computer .............................................................2
Understanding the CK30 Models and Options...........................................3
Using the CK30 Battery ...........................................................................................4
Maximizing Battery Life .............................................................................5
Checking the Battery Status........................................................................6
Charging and Installing the Battery ............................................................6
Using the Keypad .....................................................................................................7
Using the 42-Key Large Numeric and Function Keypad .............................8
Using the 50-Key Full Alphanumeric Keypad.............................................9
Using the 52-key Full Alphanumeric Keypad............................................10
Understanding How to Use the Keypad....................................................11
Capitalizing All Characters .......................................................................12
Using the International Keypad ................................................................12
Using the TE 2000 Keypad ......................................................................13
Understanding the Power Key ..................................................................13
Using the Screen.....................................................................................................14
Navigating on the Screen..........................................................................14
Understanding the Screen Icons ...............................................................14
Rotating the Screen ..................................................................................15
Using the Mouse Pointer ..........................................................................16
Understanding the LEDs ........................................................................................17
Understanding the CK30 Beeps..............................................................................18
Scanning Bar Codes................................................................................................19
Scanning With the Integrated Laser Scanner and 1D Linear Imager .........20
CK30 Handheld Computer User’s Manual iii
Contents
Scanning Bar Codes With the 2D Area Imager.........................................21
Attaching a Tethered Scanner...................................................................22
Using the SD Card .................................................................................................23
2
Configuring the CK30
...................................................................................25
How to Configure the CK30 ..................................................................................26
Configuring the CK30 With the Setup Assistant ......................................27
Configuring the CK30 With the Configuration Utility.............................28
Configuring the CK30 With Commands Through the Network ..............31
Configuring the CK30 With the Intermec Configuration Utility (ICU) ...31
Configuring the CK30 by Scanning Bar Codes.........................................31
How the CK30 Fits Into Your Network..................................................................32
Using Serial Communications on the CK30 .............................................33
Using RF Communications on the CK30.................................................34
Using Ethernet Communications on the CK30 ........................................38
Configuring the CK30 for Bluetooth
Wireless Printing ..........................39
Configuring Security on the CK30 .........................................................................40
3
Managing the CK30
........................................................................................43
Accessing the System Main Menu ...........................................................................44
Using File Manager ................................................................................................45
Using Task Manager...............................................................................................47
Using ActiveSync on the CK30...............................................................................48
Installing ActiveSync and Establishing a Partnership.................................48
Using ActiveSync to Copy Files and Install Applications...........................51
Installing Applications Using AutoCab ...................................................................52
Changing the Password...........................................................................................52
Saving Your Configuration or Application to Flash .................................................53
Upgrading the Firmware.........................................................................................53
iv CK30 Handheld Computer User’s Manual
Contents
4
Troubleshooting and Maintaining the CK30
.............................55
Problems and Solutions ..........................................................................................56
Problems While Operating the Terminal..................................................57
Problems While Configuring the Terminal...............................................57
Problems While Configuring 802.1x Security...........................................58
Problems With RF Connectivity...............................................................61
Problems Transmitting Data Through the Serial Port...............................63
Problems Transmitting Data Through the DCS 30X or G4000 ...............63
Problems While Scanning Bar Codes........................................................64
Booting the CK30 ..................................................................................................66
Warm Booting the CK30 .........................................................................66
Cold Booting the CK30 ...........................................................................67
Cleaning the Scanner Window and CK30 Screen ...................................................67
A
Appendix
................................................................................................................69
Physical and Environmental Specifications..............................................................70
Accessories for the CK30 ........................................................................................71
Using Hidden Key Sequences .................................................................................73
CK30 Handheld Computer User’s Manual v
vi
Before You Begin
Before You Begin
This section provides you with safety information, technical support information, and sources for additional product information.
Safety Summary
Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating
Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions.
Do not repair or adjust alone
Do not repair or adjust energized equipment alone under any circumstances. Someone capable of providing first aid must always be present for your safety.
First aid
Always obtain first aid or medical attention immediately after an injury. Never neglect an injury, no matter how slight it seems.
Resuscitation
Begin resuscitation immediately if someone is injured and stops breathing. Any delay could result in death. To work on or near high voltage, you should be familiar with approved industrial first aid methods.
Energized equipment
Never work on energized equipment unless authorized by a responsible authority. Energized electrical equipment is dangerous. Electrical shock from energized equipment can cause death. If you must perform authorized emergency work on energized equipment, be sure that you comply strictly with approved safety regulations.
CK30 Handheld Computer User’s Manual
Before You Begin
Safety Icons
This section explains how to identify and understand dangers, warnings, cautions, and notes that are in this document. You may also see icons that tell you when to follow ESD procedures and when to take special precautions for handling optical parts.
A warning alerts you of an operating procedure, practice, condition, or statement that must be strictly observed to avoid death or serious injury to the persons working on the equipment.
Avertissement: Un avertissement vous avertit d’une procédure de fonctionnement, d’une méthode, d’un état ou d’un rapport qui doit être strictement respecté pour
éviter l’occurrence de mort ou de blessures graves aux personnes manupulant l’équipement.
A caution alerts you to an operating procedure, practice, condition, or statement that must be strictly observed to prevent equipment damage or destruction, or corruption or loss of data.
Attention: Une précaution vous avertit d’une procédure de fonctionnement, d’une méthode, d’un état ou d’un rapport qui doit être strictement respecté pour empêcher l’endommagement ou la destruction de l’équipement, ou l’altération ou la perte de données.
Note: Notes either provide extra information about a topic or contain special instructions for handling a particular condition or set of circumstances.
Global Services and Support
Warranty Information
To understand the warranty for your Intermec product, visit the
Intermec web site at http://www.intermec.com, click Support, and then click Warranty.
CK30 Handheld Computer User’s Manual vii
Before You Begin
Disclaimer of warranties: The sample code included in this document is presented for reference only. The code does not necessarily represent complete, tested programs. The code is provided “as is with all faults.” All warranties are expressly disclaimed, including the implied warranties of merchantability and fitness for a particular purpose.
Web Support
Visit the Intermec web site at http://www.intermec.com to download many of our current manuals in PDF format. To order printed versions of the Intermec manuals, contact your local Intermec representative or distributor.
Visit the Intermec technical knowledge base (Knowledge
Central) at http://intermec.custhelp.com to review technical information or to request technical support for your Intermec product.
Telephone Support
These services are available from Intermec by calling
1-800-755-5505 and choosing an option.
Service Description
Factory Repair and
On-site Repair
Request a return authorization number for authorized service center repair, or request an on-site repair technician.
Technical Support Get technical support on your
Intermec product.
Service Contract
Status
Inquire about an existing contract, renew a contract, or ask invoicing questions.
Schedule Site
Surveys or
Installations
Schedule a site survey, or request a product or system installation.
Ordering Products Talk to sales administration, place an order, or check the status of your order.
Option
1
2
3
4
5 viii CK30 Handheld Computer User’s Manual
Before You Begin
Who Should Read This Document?
The CK30 Handheld Computer User’s Manual provides you with information about the features of the CK30, and how to install, operate, maintain, and troubleshoot them.
Before you install and configure the CK30, you should be familiar with your network and general networking terms, such as IP address.
Related Documents
The Intermec web site at http://www.intermec.com contains many of our documents that you can download in PDF format.
To order printed versions of the Intermec manuals, contact your local Intermec representative or distributor.
Patent Information
Product is covered by one or more of the following patents:
4,455,523; 5,627,360; 4,553,081; 5,657,317; 4,709,202; 5,671,436;
4,845,419; 5,684,290; 4,961,043; 5,777,309; 5,195,183; 5,793,604;
5,216,233; 5,805,807; 5,218,187; 5,818,027; 5,218,188; 5,821,523;
5,227,614; 5,828,052; 5,241,488; 5,831,819; 5,278,487; 5,834,753;
5,322,991; 5,841,121; 5,331,136; 5,844,222; 5,331,580; 5,883,492;
5,349,678; 5,883,493; 5,397,885; 5,886,338; 5,371,858; 5,889,386;
5,373,478; 5,898,162; 5,410,141; 5,969,328; 5,488,575; 5,986,435;
5,500,516; 6,075,340; 5,504,367; 6,109,528; 5,508,599; 6,158,661;
5,530,619; 6,234,395; 5,567,925; 6,244,512; 5,568,645; 6,330,975;
5,592,512; 6,431,451; 5,598,007, 6,497,368; 5,617,343; 6,538,413.
There may be other U.S. and foreign patents pending.
CK30 Handheld Computer User’s Manual ix
Before You Begin x CK30 Handheld Computer User’s Manual
1
Using the CK30 Handheld
Computer
Use this chapter to familiarize yourself with the CK30 Handheld
Computer. In this chapter you will find these sections:
• Introducing the CK30 Handheld Computer
• Using the CK30 Battery
• Using the Keypad
• Using the Screen
• Understanding the LEDs
• Understanding the Beeps
• Scanning Bar Codes
• Using the SD Card
Chapter 1 — Using the CK30 Handheld Computer
Introducing the CK30 Handheld Computer
The Intermec CK30 is the first in a new line of ergonomically designed handheld computers built on the Microsoft®
Windows® CE .NET operating system. It is a lightweight, easyto-use, reliable computer that enables you to use legacy applications as well as develop applications based on the latest technologies. The CK30 supports programming tools such as
VB.NET, C#, JavaScript, and XML.
2
Use this table to understand the features included with each model of the CK30. For a complete list of accessories, see the
Appendix.
Feature
Batch only
.Net Compact Framework
Color Display
Monochrome Display
32M/32M Memory
64M/64M Memory
200 MHz Processor
400 MHz Processor
IBrowse
Model A
9
9
9
9
9
Model B
9
9
9
9
Model C
9
9
9
9
9
CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
Understanding the CK30 Models and Options
The CK30 computer is available in three different models that consist of different options. To find out which model of the
CK30 you have, locate the configuration label on the back of the computer. The first five letters of the configuration number indicate the model of CK30 you ordered. For example, the label in the following illustration is for a CK30 model A (CK30A).
CK30AA0301000
Configuration number
C
30
A
030
10
00
This option is available for model A of the CK30:
• 10/100 base T Ethernet interface
These options are available for models B and C of the CK30:
• TE 2000 including 3270, 5250, and VT/ANSI as well as third-party TE applications
• WiFi certified 802.11b radio
• DcBrowser application
• Java™ platform
• 1D linear imager
• Bluetooth™ compatible module from Socket
Communications
These options are for the CK30 Model C only:
• 2D area imager
CK30 Handheld Computer User’s Manual 3
Chapter 1 — Using the CK30 Handheld Computer
™
CK30 Handheld Computers with an IEEE 802.11b radio installed are Wi-Fi certified for interoperability with other
802.11b wireless LAN devices.
Use this manual to understand how to use the features and options available on the CK30. For additional help using terminal emulation, see the appropriate TE 2000 guide:
• TE 2000 5250 Terminal Emulation Programmer’s Guide
(P/N 977-055-004)
• TE 2000 3270 Terminal Emulation Programmer’s Guide
(P/N 977-055-003)
• TE 2000 VT/ANSI Terminal Emulation Programmer’s
Guide (P/N 977-055-005
For additional help using dcBrowser, see the documentation that ships with your G4000, the dcBrowser gateway software, or the
Data Collection Browser Client User’s Guide (P/N 070011).
IBrowse is a locked-down web browser for Intermec devices that is compatible with Microsoft's Internet Explorer but does not allow the user to exit out of the browser or key in a URL to access a non-work related website. For additional help using
IBrowse, see ??????
Using the CK30 Battery
The CK30 uses an AB1 lithium-ion battery as its main power source. You must fully charge the main battery before you can use the CK30.
If you fail to replace the battery immediately, you may lose important data or applications.
Attention: Si la batterie n’est pas remplacée immédiatement, des données ou applications importantes risquent d’être perdues.
4 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
The lithium-ion battery pack that is used in this device may present a fire or chemical burn hazard if it is mistreated. Do not disassemble it, heat it above 100° C (212° F) or incinerate it.
Avertissement: Le paquet de piles d’ions de lithium qui est utilisé dans cet appareil peut presenter un risque feu ou un risque chimique de brûlure s’il est maltraité. Il ne faut pas le désassembler, le réchauffer à une température plus élevée que
100° C (212° F) ou l’incinérer.
Dispose of used battery packs promptly. Keep away from children. Contact your local Intermec sales representative for replacement batteries.
Several factors determine the life of your battery such as extreme temperatures, input devices, and your usage. For example, if you use a tethered scanner every day, you will need to replace your battery more often than someone who uses an internal scanner.
Maximizing Battery Life
To prolong the life of your battery, follow these guidelines.
When You Want To: Do This to Save Battery Power:
Operate the CK30 and the Low Battery status icon appears or the
Battery light comes on.
1
2
Press Power lose data.
to turn off the CK30.
Remove the battery and insert another fully charged battery within 10 minutes or you may
Or, you can insert the CK30 into a powered
AC1, AC2, AD1, or AD2.
Stop using the CK30 for 5 minutes or longer.
1 Make sure the Low Battery icon is not on the screen and that the Battery light is not turned on.
2 Press Power to turn of f the CK30.
Store the CK30 for more than a day.
1 Save your data and end your computer session.
2 Press Power to turn off the CK30.
3 Insert a fully charged battery.
CK30 Handheld Computer User’s Manual 5
Chapter 1 — Using the CK30 Handheld Computer
Checking the Battery Status
The easiest way to tell the status of your battery is to look at the battery icon in the status bar of your CK30.
Icon Status
Battery has a full charge.
Battery has a medium charge. You should be able to work for several more hours before changing batteries.
Battery is low. You need to replace the battery now.
If you cannot see a status bar on your screen, you can also check the battery status by looking at the Battery Status light on the front of the CK30. See “Understanding the LEDs” later in this chapter for more information.
Charging and Installing the Battery
Make sure you fully charge the AB1battery before you install it in your CK30.
To charge the battery
• Either insert the battery into the AC1 4-slot battery charger or place the CK30 with battery installed in the AC2, AD1, or
AD2.
Use the following table to understand how long it will take to charge your batteries in each of the CK30 charging or communications dock accessories.
CK30 Accessory
AC1 4-Slot Battery Charger
AC2 4-Bay Charging Dock
AD1 1-Bay Communications Dock
AD2 4-Bay Communications Dock
Charging Time
5 hours
5 hours
3 hours
5 hours
6 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
To install the battery
• Insert the tabs on the bottom of the charged battery into the
CK30 and snap the battery into place.
Battery latch
AB1 battery
Using the Keypad
Your CK30 has one of the following keypad overlay options:
• 42-key large numeric and function
• 50-key full alphanumeric
• 52-key full alphanumeric
Each of these keypads also comes in an International version.
The International keypads support French, German, Italian,
Portuguese, and Spanish. Although the keypads are smaller than standard PC or terminal keyboards, you can use special keys to access all of the keys and functions you need.
In addition, there are keypad overlays available for each type of
TE 2000 supported: 3270, 5250, and VT/ANSI. You receive the appropriate TE overlay when you order your TE 2000 application. Each TE 2000 keypad overlay is almost identical to the standard keypad overlay, but it contains additional keys that are available on an IBM 3270, IBM 5250, or VT/ANSI keyboard. For help using your terminal emulation keypad overlay, see your specific TE 2000 guide.
CK30 Handheld Computer User’s Manual 7
Chapter 1 — Using the CK30 Handheld Computer
Using the 42-Key Large Numeric and Function Keypad
Scan button
Orange key
Enter
CAPS
Enter
Ins
/ \
Home
Backlight key
Green key
[
Del
]
< > Sp
Power key
PROG
42-key large numeric and function keypad: Use this keypad to easily print numbers (0-9) and access function keys F1 through F12. You can also print the entire alphabet and special characters by pressing color-coded key sequences.
8 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
Using the 50-Key Full Alphanumeric Keypad
Backlight key
Power key
+
‘ “
?
Green key
Orange key
50-key full alphanumeric keypad: Use this keypad to easily print numbers
(0-9) and the entire alphabet. You can access Function keys (F1-F9) and special characters, symbols, and functions by pressing color-coded key sequences.
Note: The 50-key keypad does not have a scan key because it was designed to work with the AH1 handle that has a built-in scanner trigger.
CK30 Handheld Computer User’s Manual 9
Chapter 1 — Using the CK30 Handheld Computer
Using the 52-key Full Alphanumeric Keypad
Scan button
Orange key
Tab
Enter
Ins
&
F5
F6
+
* Home
^
Enter
F7
F8
Shift Ctl
Sp
Alt
Del
CAPS [ ]
F10 F11 F12
,
F13
F9
/ \
F14
F15
F20
<
F16
F21
>
F17
F22 F23
X
F18 F19
Z
F24
Backlight key
Green key
Power key
52-key full alphanumeric keypad: Use this keypad to easily print numbers
(0-9) and the entire alphabet. You can access Function keys (F5-F24) and special characters, symbols, and functions by pressing color-coded key sequences.
10 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
Understanding How to Use the Keypad
Each keypad available for the CK30 provides color-coded keys to let you to access additional characters, symbols, and functions printed on the keypad overlay. Once you understand how to use the color-coded keys and key sequences, you will know how to access all of the additional features printed on the keypad overlay. There are two color-coded modifier keys on the CK30: the Green key and the Orange key.
Use the CK30 modifier keys in these two ways:
• Press the key once to hold the modifier state until the next key is pressed.
• Press the key twice to lock the modifier key. Press the key again to release it.
This manual uses the following convention when referring to keys that you press in sequence. That is, you press and release the first key and then press and release the second key:
• Modifier key, key
Use this table to understand how to use the color-coded keys.
You Want To:
Use an orange character or function printed above a key
Use a green character or function printed above a key
Use a blue character printed on a key
(42-key and 50-key keypads only)
Lock the orange or green key so that you can continually access characters or functions printed above a key
Press:
Orange key, key with character or function printed above it
Green key, key with character or function printed above it
Shift key (in blue text on the key), key
Orange key twice or
Green key twice
Note: There are several hidden key functions (such as { and }) on each CK30 keypad. For more information on these hidden key sequences, refer to “Using Hidden Key Sequences” in
Appendix A.
CK30 Handheld Computer User’s Manual 11
Chapter 1 — Using the CK30 Handheld Computer
Capitalizing All Characters
To type all alphabetic characters as uppercase letters, you can do one of the following:
• Enable the Caps lock feature. For help, see the next procedure.
• Use the Keypad Caps Lock configuration command. For help, see "Keypad Caps Lock" in Chapter 6 of the CK30
Handheld Computer Configuration Manual .
To enable Caps lock
1 Press Orange key to activate the modifier key. The Orange modifier key icon appears in the status bar ( ).
2 Press one of these keys:
• On the 52-key keypad, press A .
• One the 42-key and 50-key keypad, press Shift .
The Caps lock icon ( )appears in the status bar.
3 Type an alphanumeric character. The letter appears as an uppercase character on the CK30's screen.
The Caps lock icon remains in the status bar until you disable it by pressing the same key sequence you used to enable it.
Using the International Keypad
You can order all versions of the CK30 keypad with an international overlay. The international overlay supports English and most Western European languages, such as French,
German, Italian, Portuguese, and Spanish.
You enter all of the characters and functions printed above the keys just like you would on a standard keypad. For help, see
"Understanding How to Use the Keypad" earlier in this chapter.
Note: There are several hidden key functions (such as { and }) on each international keypad. For more information on these hidden key sequences, refer to “Using Hidden Key Sequences” in Appendix A.
12 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
Using the TE 2000 Keypad
The CK30 supports TE 2000 VT100/220/320/340 and ANSI,
TE 2000 5250, and TE 2000 3270. When you order the CK30 with a TE 2000 application, you also receive the corresponding keypad overlay. Use the TE 2000 keypad overlays to enter the same keys that you can enter on a VT/ANSI keyboard, an IBM
5250 keyboard, or an IBM 3270 keyboard.
Like the standard CK30 keypad overlays, the TE 2000 keypad overlays lets you enter all the characters printed on or above the keys. The TE keypads also come with the same color-coded keys that are on the standard overlay.
For more help using TE 2000, see the appropriate TE 2000 guide.
Understanding the Power Key
When you press the Power key to turn off the terminal, you actually put the terminal in Suspend mode. In Suspend mode, the terminal continues to supply power to all memory, but turns off power to most hardware. This power-saving feature is designed to prolong battery life.
When you press the Power key to turn the CK30 back on, your computer resumes where it was when you turned it off. If you are using 802.1x security, the computer may reauthenticate before it starts your application.
If you have programmed the Resume Execution command, your
CK30 may warm boot and restart your application. For help with the Resume Execution command, see Chapter 6 of the
CK30 Handheld Computer Configuration Manual .
If your CK30 does not resume after pressing Power , you may need to warm boot it.
To warm boot the CK30
• Press and hold the Power key for five seconds. The CK30 will tell you it is performing a warm boot and the screen will come back up to the splash screen or your application.
CK30 Handheld Computer User’s Manual 13
Chapter 1 — Using the CK30 Handheld Computer
Using the Screen
The CK30 can have either a color or monochrome display depending on the model. Both screens are 160 x 160 pixels: the client area is 160 x 140 pixels and the status bar is 160 x 20 pixels. In addition, the screens support double-byte characters, user-programmable fonts, and bitmap graphics.
Client area
Status bar
Navigating on the Screen
There are several ways to navigate through the CK30 screens.
Use this table to understand what keys to press to navigate:
To Do This:
Select an option
Exit or return to a previous screen
Move back a space
Move forward a space
Press:
• The number associated with the option
• a or b to select an option and then press
Enter
• Press Tab to select an option and then press
Enter
Esc until you exit the application or return to a previous screen
• Backspace
• Orange key, a
• Orange key, b
Understanding the Screen Icons
Use the screen icons in the status bar to easily see the status of the battery, any connections to the network or applications, and any special keys or functions you may be using.
14 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
CK30 Screen Icons
Icon Description
Battery has a full charge.
Battery has a medium charge. You should be able to work for several more hours before changing batteries
Battery is low. You need to replace the battery now.
Strong connection to the network.
Medium-strength connection to the network.
Weak connection to the network.
No connection to the network.
No Ethernet connection.
Ethernet connection.
Orange modifier key pressed.
Green modifier key pressed.
Alt key is enabled.
Ctrl key is enabled.
Shift key is enabled.
Caps lock key is enabled.
Alpha lock key is enabled.
Buffered data.
You are in the password-protected area of the CK30.
The CK30 is connected using ActiveSync.
Mouse pointer turned on.
Rotating the Screen
If you turn the CK30 sideways to scan information, you might find it useful to rotate the screen 90 degrees clockwise for easier readability.
CK30 Handheld Computer User’s Manual 15
Chapter 1 — Using the CK30 Handheld Computer
To rotate the screen 90 degrees clockwise
• Press , a
Programs
Using the Mouse Pointer
If you need to use a mouse to perform an action in the Windows environment, you can use the mouse pointer that came on your
CK30.
To turn on the mouse pointer
• Press Alt key, b key.
The mouse pointer can simulate single-clicks, double-clicks, right mouse button, middle mouse button, and left mouse button functions. Use this table to understand the keys that produce each function.
To Simulate This
Function:
Left mouse button
Middle mouse button
Right mouse button
Single-click
Double-click
Mouse down event
Mouse up event
Press This Key on One of the Keypads:
42-key 50-key 52-key
F2 X B
F3 Y C
F4 Z D
5 5 5 s
0 (zero) s
0 (zero)
.
(period) Tab s
0 (zero)
For example, to generate a left single-click with the 52-key keypad
• Press , 5
16 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
Moving the mouse pointer around the screen is very easy. You just need to press the appropriate number key that is associated with the direction you want the mouse pointer to move.
Using the numeric keypad to move the mouse pointer
To continue moving the mouse pointer in one direction
• Press and hold the number key that corresponds to the direction you want to move.
Understanding the LEDs
The LEDs on the CK30 turn on to indicate the status of the battery, a successful decode of a bar code, or a user-defined function.
Good read
LED
Battery
LED
User-Defined
LEDs
Understanding the LEDs on the CK30
CK30 Handheld Computer User’s Manual 17
Chapter 1 — Using the CK30 Handheld Computer
Use this table to understand what the CK30 LEDs mean.
LED Name
User-defined
Battery status
Good Read
Icon Description
Use the CK30 Programmer’s Software Kit
(PSK) to program these LEDs to turn on and off for any task or error within your application.
For help, see the CK30 Programmer’s Software
Kit (PSK) Reference Manual.
LED Status What it means
Off The battery is fully charged
On The battery is low. Replace the battery.
This LED comes on when the CK30 successfully decodes a bar code.
Understanding the CK30 Beeps
The CK30 uses beeps to provide you with audio feedback when it performs some functions. For example, you hear a beep each time you scan a valid bar code.
Use the following table to understand what the beep sequences mean.
Beep Sequence
High beep
What it means
You entered valid data or a valid command, the computer decoded a label, or the computer decoded the last row of a two-dimensional bar code.
Three low beeps
Low beep (every 15 seconds)
You entered or scanned an invalid command or data.
The battery is low. Replace or recharge the battery as soon as possible.
Low beep, high beep Your 802.1x CK30 has been authenticated
High beep, low beep Your 802.1x CK30 is not authenticated. For help, see
“Problems While Configuring 802.1x Security” in
Chapter 4.
Click You pressed a key. You can use the Configuration
Utility to change the volume of the keyclick.
18 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
You can change the beep volume and duration to accommodate your needs and environment. When you change the beep volume, you also change the keyclick volume if you have the
Keypad Clicker command enabled. The keyclick is the sound you hear when you press a key.
You can set the beep volume to off, low, medium, and high
(default). Use one of these three ways to change the beep volume:
Method
Use the keypad.
Use the Intermec
Configuration menu.
Use the Beep
Volume command.
Procedure
Press the Green key, Backlight key to increase the volume. There are four beep volumes on the CK30 including off. When you reach the loudest setting, the next setting is off. The volume will then start with the lowest setting and go up.
From the Intermec CK30 menu, choose
Configuration Utility > CK30 Settings > Beeper and LED .
For help, see “Beep Volume” in the CK30 Handheld
Computer Configuration Manual .
Scanning Bar Codes
Do not look directly into the window area or at a reflection of the laser beam while the laser is scanning. Long-term exposure to the laser bean can damage your vision.
Avertissement: Ne regardez pas directement la réflexion d’un rayon laser ou dans la fenêtre du laser lorsque celui-ci est en opération. Si vous regardez trop longtemps un rayon laser, cela peut endommager votre vue.
Use the scanner to scan and enter bar code data. The type of scanner you are using and the type of bar code you are decoding determines the way you scan the bar code. The CK30 supports the scanning of 1D linear bar codes and 2D images depending on your model of CK30. Plus, if you have are using an integrated handle or a tethered scanner, the way you scan bar codes will be different.
CK30 Handheld Computer User’s Manual 19
Chapter 1 — Using the CK30 Handheld Computer
When you unpack the CK30, these bar code symbologies are enabled:
• Code 39
• Code 128
• UPC/EAN
• PDF 417 (with Model C only?)
If you are using bar code labels that are encoded in a different symbology, you need to enable the symbology on the computer.
Use the Configuration Utility to enable and disable symbologies for your scanner. For help understanding how to use the
Configuration Utility, see “Configuring the CK30 With the
Configuration Utility” in Chapter 2.
The next sections describe how to scan a bar code label with the integrated laser scanner, 1D linear imager and the 2D imager.
Scanning With the Integrated Laser Scanner and 1D Linear Imager
If the CK30 has a laser scanner or 1D linear imager, use the following procedure to understand how to scan a bar code. The linear imager can decode PDF417 bar codes as well as bar codes with high-density, wide-density, and poor quality in any lighting conditions.
To scan a bar code label with the laser scanner
1 Press Power to turn on the CK30.
2 Point the scanner window at the bar code label and hold the computer at a slight angle a few inches from the label.
Note: If you have an advanced long-range scanner, you may need to hold the computer further away from the label.
3 Press the Scan button on the keypad and direct the red beam so that it falls across all bars in the bar code label.
Insert illustration
20 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
When the CK30 successfully reads a bar code label, you will hear a high beep and the green Good Read LED turns on briefly.
4 Release the Scan button.
Scanning Bar Codes With the 2D Area Imager
The CK30C may have a 2D area imager instead of the conventional laser scanner. Omni-directional (360°) scanning means that you can position the CK30 in any direction to scan a bar code label.
To scan a bar code label with the 2D area imager
1 Press Power to turn on the CK30.
2 Point the scanner window at the bar code label and hold the computer a few inches from the label.
3 Press the Scan button on the keypad and center the red aiming beam over the bar code label.
Note: The aiming beam is smaller when the imager is closer to the bar code and larger when it is further away.
Insert illustration
CK30 Handheld Computer User’s Manual 21
Chapter 1 — Using the CK30 Handheld Computer
When the CK30 successfully reads a bar code label, you will hear a high beep and the green Good Read LED turns on briefly.
4 Release the Scan button.
Attaching a Tethered Scanner
You can use a tethered scanner with the CK30 if you ordered it with a 10-pin tethered scanner port in place of the integrated scanner. The following devices are currently supported by the
CK30:
• Decoded scanners: 1470B, 1551E, 1553, 1555, 1800-series laser scanners
• Undecoded scanners: 1550C, 128X wands
An auto-detection wizard automatically detects the presence of a scanner connected to the 10-pin scanner port. If the scanner is not auto-detected, an optional wizard allows you to identify scanner types that cannot be auto-detected by the CK30.
To attach a tethered scanner
1 Locate and remove the scanner port cover.
Scanner port cover
22 CK30 Handheld Computer User’s Manual
Chapter 1 — Using the CK30 Handheld Computer
2 Insert the scanner 10-pin connector until it locks in place.
Scanner port
To scanner
Using the SD Card
You can use an SD card to increase file storage and install software. The CK30 supports the following type of SD card:
• SanDisk SD cards supporting 1-bit mode only
The SD card slot is located on the top of the CK30 just above the laser scanner window. The SD card will appear in the File
Manager as "SDMMC Disk."
To insert an SD card
1 Press Power to turn on the CK30.
2 Remove the two screws on the SD card slot cover and remove the cover.
CK30 Handheld Computer User’s Manual
SD card
Cover
Screw
(2 places)
23
Chapter 1 — Using the CK30 Handheld Computer
3 Gently insert the SD card into the CK30 with the printed side facing the front of the CK30.
4 Push the card into the slot until it fits firmly.
5 Replace the cover and two screws.
24 CK30 Handheld Computer User’s Manual
2
Configuring the CK30
Use this chapter to understand how to configure the CK30 to communicate in your network. In this chapter, you will find these sections:
• How to Configure the CK30
• How the CK30 Fits Into Your Network
• Configuring Security on the CK30
Chapter 2 — Configuring the CK30
How to Configure the CK30
You can configure many operation characteristics of the CK30, such as the bar code symbologies it decodes or the network settings. These characteristics are controlled by configuration parameters. The values you set for these configuration parameters determine how the computer operates.
There are several ways to configure the CK30:
Use Applications on the CK30 Scan Bar Codes
Programs
Scan bar codes to configure basic unit and data collection parameters.
Use Setup Assistant to quickly enter network parameters or to use the
Configuration Utility to set all paramaters.
Use Intermec Configuration Utility (ICU) Use Configuration Commands
Send commands through the network to your CK30s.
Ethernet or RF
Network
Ethernet or RF
Network
Use a Web browser on your desktop PC with ICU to configure parameters for each CK30 on your network.
26 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
Configuring the CK30 With the Setup Assistant
When first setting up the CK30, use the Setup Assistant to set or enable basic network parameters and connect your CK30 to the network. The Setup Assistant is a wizard that guides you through setting the following basic network parameters:
• Date and time
• SSID (Network name)
• 802.1x security
• DHCP server or IP address, subnet mask, and default router
• Primary and secondary DNS addresses
• Primary and secondary WINS addresses
• Device name
To set other parameters, use the Configuration Utility or another configuration method. The Setup Assistant runs on the
CK30 the first time you turn on the computer.
The first screen of the Setup Assistant Wizard
However, if you exit Setup Assistant before you are finished configuring the CK30, you can restart it from the SSystem Main
Menu. See the next section for information on how to access the
System Main Menu .
After you complete the Setup Assistant, the CK30 should be communicating with your network. If you are using RF communications on your CK30, a network connection icon appears in the status bar.
CK30 Handheld Computer User’s Manual 27
Chapter 2 — Configuring the CK30
Configuring the CK30 With the Configuration Utility
Use the menu-driven Configuration Utility to configure the
CK30 and view system information. You can access the
Configuration Utility while running any application.
Opening the Configuration Utility
When using the Configuration Utility, you may not see a parameter until you enable or disable a value for another key field. For example, you will not see IP Settings unless you disable
DHCP. You may also not see a parameter if your computer does not support a particular feature.
To open the Configuration Utility
1 From the CK30 splash screen, press Green key, Orange key.
2 In the password dialog box, type intermec
and press Enter .
The System Main Menu appears.
An icon ( ) appears in the status bar showing that you are in the password-protected area of the CK30.
3 Select the Configuration Utility . The Configuration Utility main menu appears.
28 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
Use this table to understand your menu options in the
Configuration Utility.
Configuration Utility Menu Options
Menu Option
Communications
Description
Scanners, Symbologies Configure scanner settings and bar code symbologies.
Set up network settings including the 802.11b radio and the Bluetooth printer.
CK30 Settings Configure settings specific to the CK30 such as the date, time, beeper volume, and backlight timeout.
SNMP
About the CK30
Summary
Restore Defaults
??
View the part number, firmware version, radio, and
RF protocol loaded on your CK30.
View a summary of all settings for the Scanners,
Symbologies menu, the Communications menu, the CK30 Settings menu, and the SNMP menu.
Restore factory default settings on your CK30.
Configuration Utility Menus at a Glance (placeholder graphic)
CK30 Handheld Computer User’s Manual 29
Chapter 2 — Configuring the CK30
Use this table to understand how to navigate and enter information in the Configuration Utility .
To Do This:
Select an option
Save a setting
Exit or return to a previous screen
Move back a space
Move forward a space
Delete a character
Delete all characters in a field when highlighted
Press:
• The number associated with the option
• a or b to select an option and then press
Enter
• Tab to select an option and then press
Enter
Enter key
Esc until you exit the application or return to a previous screen
• Backspace
• Orange key, a
• Orange key, b
Green key, Backspace ( ) key
Backspace ( ) key
Restoring Default Settings
You can restore the CK30 to factory default settings from the
Configuration Utility.
Note: Using the Restore Defaults option resets all network parameters. As a result, you may lose network communications.
This option should only be used by network administrators or by Intermec support personnel.
To restore factory default settings
1 From the Configuration Utility menu, select Restore
Defaults . The following Alert box appears:
30 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
2 Press Enter to restore factory defaults.
A progress bar appears on the screen to show you the status of restoring the factory defaults.
Exiting the Configuration Utility
When you exit the Configuration Utility, you leave the password-protected area of the CK30. The password-protected icon ( ) disappears from the status bar.
To exit the System Main Menu
1 From the System Main Menu , press Esc or select Exit .
2 When asked if you want to exit the System Main Menu , press Enter .
Configuring the CK30 With Commands Through the Network
You can change the configuration parameters of the CK30 by sending commands through a host computer or through the network. If you are using a network, you can configure one or more CK30 at a time. For help, see Chapter 2 of the CK30
Handheld Computer Configuration Manual .
Configuring the CK30 With the Intermec Configuration Utility (ICU)
I don’t have any information to put here yet….
Configuring the CK30 by Scanning Bar Codes
You can change the configuration parameters of the CK30 by scanning Code 39 or Code 93 bar codes labels containing configuration commands. This method is a fast and easy way to change just a few configuration parameters on a single CK30.
You can scan the bar code labels in the CK30 Handheld
Computer Configuration Manual or you can create your own bar code labels. Chapter 2 in the Configuration Manual describes how to create your own bar code labels.
CK30 Handheld Computer User’s Manual 31
Chapter 2 — Configuring the CK30
You can only change some of the configuration parameters by scanning bar codes. To configure all of configuration parameters, use the Configuration Utility, send commands through the network to your Ck30, or use the Intermec
Configuration Utility.
For example, you can use the Beep Volume configuration command to adjust the beep volume of the CK30. Scan this bar code label to set the volume to the lowest level:
Set Beep Volume to Low
*$+BV1*
*$+BV1*
When you scan bar code configuration commands, the CK30 emits a series of beeps unless the volume is turned off. There are two beep sequences:
• One high beep means you scanned a valid configuration command.
• Three low beeps means you scanned an invalid configuration command.
How the CK30 Fits Into Your Network
The CK30 is a versatile handheld computer that you can easily add to your wired or wireless data collection network. You can connect your CK30 to your network using:
• Serial Communications
• RF Communications
• Ethernet Communications
• Bluetooth Wireless Printing
32 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
Using Serial Communications on the CK30
The CK30 has a serial port to transfer data to and receive data from another device via RS-232 communications. You can also insert the CK30 into a communications dock to transmit data to and receive data from a host computer or PC using serial communications.
Mainframe
File server
Ethernet
Terminals
Serial cable
PC
CK30
To use serial communications with your CK30
1 Turn off the CK30.
2 Connect the CK30 to the serial port of another device. You can do this in one of the following ways:
• Connect the CK30 serial port to the serial port of the other device using the AA1A (26-pin to DB9-pin) serial adapter cable.
CK30 Handheld Computer User’s Manual 33
Chapter 2 — Configuring the CK30
• Connect the AD1 or AD2 Communications Dock to the serial port of the other device using a DB9-pin to DB9-pin serial adapter cable.
3 Turn on the CK30.
Using RF Communications on the CK30
Make sure all components with antennas are at least 30 cm
(1 ft) apart when power is applied. Failure to comply could result in equipment damage.
Attention: Assurez-vous que la distance entre tous les
éléments avec antennes soit d’au moins 30 centimètres (un pied) avant de faire la connexion avec l’alimentation
électrique, faute de quoi vous risquez d’endommager votre installation.
The CK30 has an internal antenna to transfer data using RF communications. This section of the manual assumes that you have already set up your RF communications network including your access points. If you are using a UDP Plus network, you also need to have your DCS 30X or G4000 communicating with a host computer.
If you are using 802.1x security, this section also assumes that your authentication server and access points are properly configured and that they have been set to the current date and time.
Your CK30 supports one of the following types of network protocol:
• TCP/IP
• UDP Plus
The next sections explain the parameters you need to configure for the CK30 to work in your RF network.
34 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
Configuring the Network Parameters for a TCP/IP Network
In a TCP/IP network, the CK30 communicates with a host computer directly using TCP/IP for the RF protocol. The access point acts as a bridge to allow communications between the wired network and the RF network.
Host
TCP/IP
Direct Connect
Ethernet
Access point
CK30s
To use RF communications in a TCP/IP network
1 Configure these network parameters on each CK30 in the network:
• Network Name (SSID)
• Host IP Address
CK30 Handheld Computer User’s Manual 35
Chapter 2 — Configuring the CK30
• IP Settings (if not using DHCP)
• Network Port
2 Configure the security.
The easiest way to configure the network parameters on the
CK30 is to use the Configuration Utility. For help, see
“Configuring the CK30 With the Configuration Utility” on page 28.
Configuring the Network Parameters for a UDP Plus Network
In a UDP Plus network, the CK30 communicates with a host computer through the DCS 30X or the G4000.
Host
UDP Plus
Ethernet
G4000
Access point
CK30s
36 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
The DCS 30X or G4000 translate UDP Plus packets on the RF network into TCP/IP packets on the wired network and vice versa. The access point acts as a bridge to allow communications between the wired network and the RF network.
To use RF communications in a UDP Plus network
1 Configure these network parameters on each CK30 in the network:
• Network Name (SSID)
• Controller IP Address
• IP Settings (if not using DHCP
• Network Port
• Default Router (DCS 30X or G4000 on different subnetwork)
• Subnet Mask (DCS 30X or G4000 on different subnetwork)
2 Configure the security.
The easiest way to configure the network parameters on the
CK30 is to use the Configuration Utility. For help, see
“Configuring the CK30 With the Configuration Utility” on page 28.
CK30 Handheld Computer User’s Manual 37
Chapter 2 — Configuring the CK30
Using Ethernet Communications on the CK30
You can use the CK30 directly in an Ethernet network if you have ordered Ethernet on your CK30 and you insert it into an
AD1 or AD2 communications dock. The communications dock has an Ethernet connector that makes it possible for the CK30 to connect to your Ethernet network.
Host
File server
38
Ethernet
Terminals
PC
243X hardwired to PC
To use the CK30 in an Ethernet network
1 Either enable DHCP or configure these network parameters on each CK30 in the network:
• IP Address
• Subnet Mask
• Default Router
2 If required for your network, set these parameters on each
CK30 in the network:
• Primary and Secondary DNS Servers
• Primary and Secondary WINS Servers
CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
Configuring the CK30 for Bluetooth
Wireless Printing
You can send information to printers wirelessly using the
Bluetooth qualified module by Socket Communications. The
Bluetooth technology uses short-range radio links and allows for communications over a ten-meter range.
To configure the CK30 for wireless printing
1 Go to Configuration Utility > Communications >
Bluetooth .
2 Select Set Wireless Printer to start the Bluetooth device discovery. A list of discovered devices appears in the Devices dialog box.
3 Select the device you want to use from the list and press
Enter .
If devices are discovered, but your device is not displayed, make sure your device and radio are turned on and try device discovery again.
Use this table to understand the parameters you see in the
Bluetooth menu.
Parameter
Remote Device Name
Description
Name of the remote Bluetooth compatible printer.
Remote Device Address The network address of the Bluetooth compatible printer.
Set Wireless Printer
Device Name
Device Address
Discovers Bluetooth compatible devices.
The name assigned to your CK30.
The network address of your CK30.
CK30 Handheld Computer User’s Manual 39
Chapter 2 — Configuring the CK30
Bluetooth Parameter Descriptions (continued)
Parameter
Discoverable
Connectable
Class of Device
Description
Makes your CK30 discoverable on the network.
Makes your CK30 connectable on the network.
Determines how the device appears to other devices during discovery.
For more information about using Bluetooth communications, see the Wireless Printing Development Guide available on the Intermec Developer’s Library CD .
Configuring Security on the CK30
The CK30 uses the Wired Equivalent Privacy (WEP) protocol to provide your wireless networks the same level of protection as a comparable wired network. WEP adds security to wireless local area networks (WLANs) based on the 802.11b standard. You can enable or disable WEP security.
To use 802.11 security, you need:
• An Intermec MobileLAN access point with an 802.11b radio and software release 1.80 or later.
• A CK30 handheld computer with an 802.11b radio and the wireless security option.
To enable WEP security on the CK30
1 Make sure you have configured the communications and radio parameters on your CK30.
2 Open the Configuration Utility. For help, see “Configuring the CK30 With the Configuration Utility” earlier in this chapter.
3 Enable WEP Encryption.
4 Set the value of each of the four WEP keys.
40 CK30 Handheld Computer User’s Manual
Chapter 2 — Configuring the CK30
You can enter either an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5-byte value for WEP 64-bit or a 13-byte value for WEP 128-bit. Hex keys must be preceded by 0x and contain 10 or 26 hex numbers.
For example, to enter a key with the value of ABCDE for a radio that supports WEP 64-bit:
• Enter ABCDE for an ASCII key
• Enter 0x4142434445 for a hex key
5 Select the WEP key you want to use for data transmission.
6 Exit the Configuration Utility .
CK30 Handheld Computer User’s Manual 41
Chapter 2 — Configuring the CK30
42 CK30 Handheld Computer User’s Manual
3
Managing the CK30
Use this chapter to understand how to manage information on the CK30. In this chapter, you will find these sections:
• Accessing the System Main Menu
• Using File Manager
• Using Task Manager
• Using ActiveSync on the CK30
• Installing Applications Using AutoCab
• Changing the Password
• Saving Your Configuration or Application to Flash
• Upgrading the Firmware
Chapter 3 — Managing the CK30
Accessing the System Main Menu
You need to access the System Main Menu to be able to use most of the tools for managing the CK30. Access to the System
Main Menu is password protected to ensure that only authorized individuals can use it.
To access the System Main Menu
1 From the CK30 splash screen, press Green key, Orange key.
2 In the password dialog box, type intermec
and press Enter .
The System Main Menu appears.
44
Note: When you access the System Main, an icon ( ) appears in the status bar indicating that you are in the passwordprotected area of the CK30.
To exit the System Main Menu
• From the , press Esc or select Exit from the list.
When you exit the System Main Menu, the icon disappears from the status bar.
CK30 Handheld Computer User’s Manual
Chapter 3 — Managing the CK30
Using File Manager
File Manager provides the ability to run an executable file, delete a file, or view the properties of a file.
To open File Manager
• From the , select File Manager .
The File Manager screen appears.
To run an application
1 Navigate to the folder containing the application file.
2 Select the file by pressing its associated number or by scrolling to it and pressing Enter . The following dialog box appears:
3 Select Run and press Enter . Your application opens.
CK30 Handheld Computer User’s Manual 45
Chapter 3 — Managing the CK30
To delete a file
1 Navigate to the folder containing the file you want to delete.
2 Select the file by pressing its associated number or by scrolling to it and pressing Enter .
3 From the dialog box, select Delete and press Enter .
4 When the screen asks for confirmation that you want to delete the file, Press Enter .
The file is deleted and you remain in the selected folder.
To view the properties of a file
1 Navigate to the folder containing the file you want to view.
2 Select the file by pressing its associated number or by scrolling to it and pressing Enter .
3 From the dialog box, select Properties and press Enter . A screen appears showing you the details of the file. For example, you should see something similar to this screen:
4 Press any key to return to the File Manager.
46 CK30 Handheld Computer User’s Manual
Chapter 3 — Managing the CK30
Using Task Manager
Task Manager provides information about applications running on the CK30. You do not need to use the System Main Menu to access Task Manager - you can access Task Manager at any time.
Use Task Manager to perform several tasks, such as:
• View all applications currently running on the CK30
• Close an application
• Switch between applications
To view applications currently running on the CK30
• Press , Tab
The Task Manager dialog box appears with the active application selected.
To close an application
1 Select the application you want to close. The following list box appears:
2 Scroll to End Task and press Enter .
CK30 Handheld Computer User’s Manual 47
Chapter 3 — Managing the CK30
The application closes and you return to the System Main
Menu .
To switch between applications
1 Select the application you wan to close.
2 Select Switch To and press Enter .
The application you selected now appears on the screen.
Using ActiveSync on the CK30
You can use ActiveSync to establish a connection between your desktop PC and the CK30. ActiveSync allows you to transfer files, synchronize files, perform remote debugging, and other device management activities. ActiveSync is a free application available from the Microsoft
website.
To establish a partnership between your desktop PC and the
CK30, you will need:
• A USB cable
• An AD1 or AD2 communications dock
• ActiveSync version 3.7 or later
Installing ActiveSync and Establishing a Partnership
You must use a USB cable to establish your initial partnership between the CK30 and your desktop PC. If you are running
Windows NT on your desktop PC, you cannot connect to your
CK30 with ActiveSync.
To install ActiveSync and establish a partnership
1 Download ActiveSync from the Microsoft website and follow the onscreen instructions for installing it on your desktop PC.
When the installation process is complete, the Get
Connected dialog box appears:
48 CK30 Handheld Computer User’s Manual
Chapter 3 — Managing the CK30
The ActiveSync Get Connected dialog box
2 Connect the AD1 to your desktop PC with the USB cable
3 Click Next in the Get Connected dialog box. ActiveSync detects a device on the USB port and prompts you to set up a new partnership.
4 In the Set Up a Partnership dialog box, click Next .
5 In the Select Number of Partnerships dialog box, select Yes,
I want to synchronize with only this computer and then click Next .
6 In the Select Synchronization Settings dialog box, check the items you want to synchronize and click Next .
7 In the Setup Complete dialog box, click Finish .
CK30 Handheld Computer User’s Manual 49
Chapter 3 — Managing the CK30
When the partnership has been established, the following screen appears on your desktop showing the device name of your CK30 and the Connected status.
50
The Microsoft ActiveSync screen
An icon also appears in the CK30 status bar indicating that it has established an ActiveSync partnership with your desktop PC.
Note: If ActiveSync does not establish a partnership on the first try, the Get Connected dialog box appears on your desktop with the message “Your device was not detected.” Click Next on the Get Connected dialog box until your device is detected.
Now that the partnership has been established, all future connections will be handled through ActiveSync. To connect to your PC using ActiveSync in the future, all you need to do is place a CK30 in the AD1 or AD2 communications dock or turn on the CK30 by pressing Power .
CK30 Handheld Computer User’s Manual
Chapter 3 — Managing the CK30
Using ActiveSync to Copy Files and Install Applications
You can use ActiveSync to copy files to the CK30 and to install applications. Basically, to install an application, you need to copy the .cab file to a directory on the CK30 and then run it.
Use the following procedures to learn how to copy files and install applications on the CK30 using ActiveSync.
To copy a file to the CK30
1 Connect the CK30 to your desktop PC using ActiveSync. For help, see the previous section “Installing ActiveSync and
Establishing a Partnership.”
2 In ActiveSync, click Explore . Windows Explorer will open the Mobile Device window of your CK30:
3 In Windows Explorer, browse to the file that you want to copy on your device or desktop computer.
CK30 Handheld Computer User’s Manual 51
Chapter 3 — Managing the CK30
4 Right-click the file and click Copy .
5 Place the cursor in the desired folder for your device, rightclick, and click Paste .
The file has now been copied to the CK30 and you will be able to see it using File Manager.
To install an application on the CK30
1 Open File Manager on the CK30.
2 Navigate to the .cab file you want to install.
3 Select the file by pressing its associated number or by scrolling to it and pressing Enter .
4 Select Run from the dialog box and press Enter .
The .cab file executes and your application begins the installation process on the CK30.
Installing Applications Using AutoCab
Still waiting to see how this is going to work on the CK30…
Changing the Password
You may want to change the password from the default
( intermec
) to help restrict access to the SSystem Main Menu.
The Change Password dialog box is very easy to access and to use.
To change the password
1 From the CK30 splash screen, press Green key, Orange key.
2 In the password screen, type intermec
and press Enter . The
System Main Menu appears.
52 CK30 Handheld Computer User’s Manual
Chapter 3 — Managing the CK30
3 From the System Main Menu, select Change Password . The
Change Password dialog box appears:
4 Type intermec
in the Old Password field.
5 Press Tab to move to the New Password field.
6 Type your new password and then press Tab to move to the
Retype New field.
7 Type your new password in again.
8 Press Enter.
The screen displays a message reading “Password successfully changed.”
Saving Your Configuration or Application to Flash
There is now an option to save the configuration or applications to Flash. There will be a menu option at the System Main Menu level for applications and a menu option at the Configuration
Utility level. Saving the changes to Flash ensures that the changes will be persistent – that is, that the changes will be there after the CK30 is cold-booted.
Upgrading the Firmware
How is this done?
CK30 Handheld Computer User’s Manual 53
Chapter 3 — Managing the CK30
54 CK30 Handheld Computer User’s Manual
4
Troubleshooting and
Maintaining the CK30
Use this chapter to solve problems you may encounter while using the CK30. You will also find information on booting the computer and routine maintenance.
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems and Solutions
If you have any problems using the CK30, look in this chapter to find a possible solution. This chapter consists of the following sections:
Sections
Problems While Operating the CK30
Problems While Configuring the CK30
Page
4-57
4-57
Problems While Configuring 802.1x Security
Problems With RF Connectivity
4-58
4-61
Problems Transmitting Data Through the Serial Port 4-63
Problems Transmitting Data Through the DCS 30X or G4000 4-63
Problems While Scanning Bar Codes
Booting and Resetting the CK30
Cleaning the Scanner Window and Computer Screen
4-64
4-66
4-67
You can also use the error numbers and messages table and the terminal diagnostics to help analyze and solve problems. For help, see Chapter 4, “Running Diagnostics,” in the CK30
Handheld computer configuration Manual (P/N 073528) .
If you have problems with the TE 2000 terminal emulation applications, see the appropriate TE 2000 guide.
If you send the CK30 in for service, it is your responsibility to save the terminal data and configuration. Intermec is responsible only for ensuring that the keypad and other hardware features match the original configuration when repairing or replacing your computer.
56 CK30 Handheld Computer User’s Manual
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Operating the Terminal
Problem
You press Power to turn on the
CK30 and nothing happens.
The Battery light is on and the terminal beeps once every 15 seconds.
The terminal appears to be locked up and you cannot enter data.
Solution
Make sure you have a charged battery installed correctly. For help, see “Charging and Installing the Battery” in Chapter 1.
The battery may be discharged. Replace the battery pack with a spare charged battery, or charge the battery and try again.
The battery charge is low. You have a few minutes of power left. Immediately replace the battery with a spare charged battery pack, or charge the battery.
• Press to turn on the CK30. The CK30 boots all the systems, clears RAM memory, and starts the application.
• Remove the battery pack. Let the terminal sit for 1 minute. Install the battery pack. Press Power to turn on the CK30.
• (CK30 with an 802.11b radio only) Wait at least 10 seconds and try again. If the CK30 is still connecting to the G4000 or the host, it ignores any input from the keypad or scanner.
• Try reloading the firmware. For help, see “Upgrading the
Firmware” in Chapter 3.
• If the CK30 will not boot or reset, contact your local
Intermec service representative for help.
Problems While Configuring the Terminal
Problem
You scan a configuration command, such as Keypad Caps
Lock, and nothing happens.
Solution
There are two possible solutions:
• You may have one or more reader commands disabled, such as Change Configuration, so that you cannot change the configuration. Enable all of the reader commands and try again.
CK30 Handheld Computer User’s Manual 57
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Configuring the Terminal (continued)
Problem
You scan or enter an option for the
Scanner Selection configuration command and you hear three low beeps.
You scan a configuration command, such as Keypad Caps Lock, and you hear three low beeps.
Solution
• The terminal may be waiting for another command to complete the configuration change. If you started by scanning the Enter Accumulate command, you must finish the command by scanning the Exit Accumulate command. For help, see Chapter 6, “Configuration Command
Reference,” in the CK30 Handheld Computer
Configuration Manual .
Scan the Enable Override to temporarily enable all of the reader commands. When you are finished, remember to disable the override so that your data is not interpreted as a command.
Enable Override
*$+DC3*
*$+DC3*
You may have scanned or entered a Scanner Selection command that does not apply to the type of scanner that you have installed. Try scanning or entering the
Scanner Selection command again and select an option for the type of module you have installed.
If you are working in the CK30 System Main Menu, you cannot scan configuration commands. Use the
Configuration Utility to change the CK30 configuration, or exit the system menu to scan configuration commands.
Problems While Configuring 802.1x Security
If you have trouble configuring the terminal for 802.1x security, check these problems and possible solutions. For more error numbers and messages, see “802.1x Security Error Numbers and
Messages” in Chapter 4 of the CK30 Handheld Computer
Configuration Manual .
This section references error numbers that are displayed on the
Error Logger screen in the Diagnostics menu. To view the Error
Logger screen, from the System Main Menu , choose
Diagnostics > Software Diagnostics > Error Logger .
58 CK30 Handheld Computer User’s Manual
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Configuring 802.1x Security
Problem
The CK30 indicates that it is authenticated by emitting a low beep and a high beep, but it does not communicate with the host.
Possible Solution
Make sure that the CK30 IP address, host IP address, subnet mask, and default router are properly configured for your network.
Note: Do not cold boot the terminal. Cold booting the terminal resets the time and date.
The “AUTHENTICATING” message does not appear on the screen, and a network connection icon is not in the status bar.
The “AUTHENTICATING” message does not appear on the screen. A network connection icon appears in the status bar, but it disappears.
The terminal indicates that it is not authenticated by emitting a high beep and a low beep.
This error code appears on the Error
Logger screen:
0x377
The terminal may not be communicating with your
MobileLAN access point. Make sure the network name on the CK30 is the same as the network name (SSID) of the access point that you are trying to communicate with. The default network name is “INTERMEC.”
The 802.1x security network may not be active. Make sure that the Odyssey server software is properly loaded and configured on the server PC. For help, see the documentation that shipped with your server software.
The CK30 may not be communicating with the
MobileLAN access point that you want it to communicate with. Make sure that the network name on the CK30 is the same as the network name of the access point that you are trying to communicate with. The default network name is
“INTERMEC.”
The MobileLAN access point that you are trying to communicate with may not be communicating with the
Odyssey server. Make sure your MobileLAN access point is turned on, properly configured, and has 802.1x security enabled.
Make sure that:
• The User Name and Password parameters on your
CK30 match the user name and password on your
Odyssey server. You may need to re-enter the password on both your CK30 and Odyssey server.
• On your Odyssey server, the user and group are allowed and the group policy is allowed to log in to the Odyssey server. For help, see the documentation that shipped with your Odyssey server software.
CK30 Handheld Computer User’s Manual 59
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Configuring 802.1x Security (continued)
Problem
The “AUTHENTICATING” message appears on the screen, but the CK30 does not emit a low beep and a high beep to indicate that it is authenticated.
Solution
• The IP address and secret key for your MobileLAN access point must match the IP address and secret key on your
Odyssey server. You may need to re-enter the IP address and secret key on both your MobileLAN access point and
Odyssey server.
• Your Odyssey server is active and that it can communicate with your MobileLAN access point. You can use the PING command to determine communications.
• The Odyssey server software is running on the server PC.
• The UDP port (standard RADIUS port, 1812) on your
Odyssey server is active. For help, see the documentation that shipped with your Odyssey server software.
The CK30 takes up to 60 seconds to authenticate; however, this process may take longer if there is interference in RF communications. You may need to wait for the authentication process to finish.
You may be out of range of the MobileLAN access point you are trying to communicate with. Try moving closer to the
MobileLAN access point.
The authentication process timed out. You may be out of range of the MobileLAN access point that you are trying to communicate with. Try moving closer to the MobileLAN access point.
The “AUTHENTICATING” message appears on the screen, but the CK30 does not emit a low beep and a high beep to indicate that it is authenticated.
This error code appears on the Error
Logger screen:
0x37B
The CK30 indicates that it is not authenticated by emitting a high beep and a low beep.
One of these error codes appears on the Error Logger screen:
0x50A or 0x509
The time and date on your CK30 does not fall within the range of valid dates indicated on the server certificate. Modify the time and date so that it falls within the range of valid dates. For help, see “Time and Date” in Chapter 6 of the CK30 Handheld
Computer Configuration Manual .
60 CK30 Handheld Computer User’s Manual
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Configuring 802.1x Security (continued)
Problem
The terminal indicates that it is not authenticated by emitting a high beep and a low beep.
This error code appears on the Error
Logger screen:
0x513
The terminal indicates that it is not authenticated by emitting a high beep and a low beep.
This error code appears on the Error
Logger screen:
0x542
Possible Solution
The root Certificate Authority certificate on your terminal cannot validate the server certificate.
• Make sure your Odyssey server is using a server certificate that matches the root certificate loaded on your terminal.
• Verify the root certificate in the CACERT.PEM file on your terminal’s C drive. WHERE WILL THIS BE ON
THE CK30?
For help, see the documentation that shipped with your
Odyssey server software.
Neither of the server certificate common names configured on your terminal match the server certificate common name in the active server certificate on your Odyssey server.
• Delete both server certificate common names on your terminal to see if you can authenticate without checking the server certificate common name.
• Change one or both server certificate common names on your terminal so that they match the server certificate common names in the active server certificate on your Odyssey server.
For help, see “Server Certificate Common Name” in
Chapter 6 of the CK30 Handheld Computer Configuration
Manual .
Problems With RF Connectivity
Problem
You are having problems with your
802.11b RF network coverage.
Solution
Make sure that the Multiple Density Distribution
(MDD) command on your access point is not enabled.
When MDD is enabled, the access point distributes values for these RF coverage parameters to your terminal: AP Density and Medium Reservation.
Changes made by your access point are not reflected in the terminal menu system.
CK30 Handheld Computer User’s Manual 61
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems With RF Connectivity (continued)
Problem
When you turn on the terminal after it was suspended for a while (10-15 minutes or longer), the terminal can no longer send or receive messages over the network.
The no network connection icon appears in the status bar. The CK30 is not communicating with the access point.
The CK30 is connected to the G4000 or host computer and you move to a new site to collect data. The network connection icon was visible but now the no network connection icon is visible.
Possible Solution
The host may have deactivated or lost your current terminal emulation session. In a TCP/IP direct connect network, you need to turn off the “Keep Alive” message
(if possible) from the host so that the TCP session is maintained while a terminal is suspended.
The CK30 is not connected to the access point. Make sure the access point is turned on and operating. You may also be using the terminal out of range of an access point. Try moving closer to an access point to reestablish communications. If you are using a
MobileLAN access point with firmware release 1.34 or earlier, it may not be able to communicate with the terminal. For help upgrading your access point firmware, see the MobileLAN access System Manual (P/N 067150).
Make sure the CK30 is configured correctly for your network. The radio parameters on the terminal must match the values set for all access points the terminal may communicate with. For help, see “Using RF
Communications on the CK30” in Chapter 2.
If you have an 802.11b radio, the radio initialization process may have failed. Try resetting the CK30. See
“Booting the CK30” later in this chapter.
If you have tried these possible solutions and the no network connection icon still appears, you may have a defective radio card. For help, contact your local
Intermec service representative.
You may have gone out of range of an access point. Try moving closer to an access point or to a different location to re-establish communications. Once you are in range again, the network connection icon will appear again. Any data you collected while out of range will be transmitted over the network.
62 CK30 Handheld Computer User’s Manual
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems With RF Connectivity (continued)
Problem
The network connection icon is in the status bar, but you cannot establish a terminal emulation session with the host computer.
The network connection icon is in the status bar, but the host computer is not receiving any data from the CK30.
Possible Solution
There may be a problem with the host computer, a problem with the connection between the G4000 and the host computer, or a problem with the connection between the access point and the host computer. Check with your network administrator to make sure the host is running and allowing users to login to the system.
In a UDP Plus or WTP network, there may be a problem with the connection between the G4000 and the host computer. Check with your network administrator or see the user’s manual for the G4000.
In a TCP/IP network, there may be a problem with the connection between the access point and the host computer. Check with your network administrator or use your access point user’s manual.
Problems Transmitting Data Through the Serial Port
If you are having problems sending or receiving data through the integrated I/O port on the terminal, check these possible problems:
• Make sure the terminal is connected to the PC, host computer, or RS-232 serial device using the appropriate cable.
• If the terminal is in a communications dock, make sure that the communications dock is connected to the serial device using the appropriate cable.
Problems Transmitting Data Through the DCS 30X or G4000
Problem
Transaction Buffer Full.
Solution
The buffer holding transactions to be sent to the DCS
30X or G4000 is full. Stop collecting data with this terminal. Make sure the terminal is communicating with the DCS 30X or G4000 and let the terminal send all the transactions in the buffer before you continue collecting data.
CK30 Handheld Computer User’s Manual 63
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems Transmitting Data Through the DCS 30X or G4000 (continued)
Problem
Sending Buffer Transactions.
Transaction Aborted.
Transmit Error XX, press Enter.
Receive Error XX, press Enter.
Shutting down.
Controller Shutdown.
Solution
This is an information message to tell you that buffered transactions are now being sent to the DCS 30X or
G4000. You can begin collecting data again once the message clears.
The transaction just sent to the DCS 30X or G4000 was not received. Try sending the transaction again.
There is an error transmitting data to the DCS 30X or
G4000. XX represents the status code error. Note the error code listed in the message and contact your local
Intermec service representative for help. Press Enter to continue.
There is an error receiving data from the DCS 30X or
G4000. XX represents the status code error. Note the error code listed in the message and contact your local
Intermec service representative for help. Press Enter to continue.
The DCS 30X or G4000 is shutting down. You may continue collecting data and buffer the transactions in the terminal until the DCS 30X or G4000 starts again, or stop collecting data with the terminal.
The DCS 30X or G4000 has shut down. You may continue collecting data and buffer the transactions in the terminal until the DCS 30X or G4000 starts again, or stop collecting data with the terminal.
Problems While Scanning Bar Codes
Problem
You cannot see a red beam of light from the scanner when you press the Scan button and aim the scanner at a bar code label.
Solution
There are two possible problems:
• You may be too far away from the bar code label.
Try moving closer to the bar code label and scan it again.
• You may be scanning the bar code label “straight on.” Change the scanning angle and try again.
You can test the effective range of the scanner. Move within 2 feet of a wall and test the scanner. You need to be within the scanning range to scan bar code labels. For help on scanning distances, see “Specifications” in
Appendix A.
64 CK30 Handheld Computer User’s Manual
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Scanning Bar Codes (continued)
Problem
When you release the Scan button, the
Good Read LED does not turn off.
You have an input device attached to the terminal and it cannot read any bar codes.
The input device attached to the terminal does not appear to work well or read bar code labels very quickly.
The scanner will not read the bar code label.
The scanner does not read the bar code labels quickly, or the scanning beam seems to be faint or obscured.
Solution
The Good Read LED will remain on if you configure the terminal to use edge triggering. If you configure the terminal for level triggering and the Good Read LED remains on, there may be a problem. Press the Scan button again without scanning a bar code label. If the
LED is still on, contact your local Intermec service representative.
You may not be using an input device that is supported with the terminal. Make sure you are using one of the supported input devices.
Try setting the Scanner Selection command to the specific input device you have attached. Check the bar code symbologies you have enabled on the terminal.
Enable only the symbologies that you are using.
Make sure you aim the scanner beam so it crosses the entire bar code label in one pass.
The angle you are scanning the bar code label may not be working well, or you may be scanning the label
“straight on.” Try scanning the bar code label again, but vary the scanning angle.
The bar code label print quality may be poor or unreadable. To check the quality of the bar code label, try scanning a bar code label that you know scans.
Compare the two bar code labels to see if the bar code quality is too low. You may need to replace the label that you cannot scan.
Make sure the bar code symbology you are scanning is enabled. Use the Configuration Utility to check the symbologies. On the Symbologies Menu, each symbology that is enabled has a check mark ( ➼ ) next to the name of the symbology. If your bar code symbology is disabled, enable it and then try scanning the bar code label again.
Make sure that the application you are running on the terminal is expecting input from a bar code. You may need to type this information instead of scanning it.
The scanner window may be dirty. Clean the window with a solution of ammonia and water. Wipe dry. Do not allow abrasive material to touch the window.
CK30 Handheld Computer User’s Manual 65
Chapter 4 — Troubleshooting and Maintaining the CK30
Problems While Scanning Bar Codes (continued)
Problem
You scan a reader command, such as
Backlight On, and nothing happens.
Solution
The reader commands are disabled. Scan the Enable
Override command shown here to temporarily enable all of the reader commands. When you are finished, remember to disable the override so that your data is not interpreted as a command.
You scan a valid bar code label to enter data for your application. The data decoded by the scan module does not match the data encoded in the bar code label.
Enable Override
*$+DC3*
*$+DC3*
The terminal may have decoded the bar code label in a symbology other than the label’s actual symbology. Try scanning the bar code label again. Make sure you scan the entire label.
To operate the terminal quickly and efficiently, you should enable only the bar code symbologies that you are going to scan.
Booting the CK30
You seldom need to warm or cold boot the CK30. The CK30 uses the configuration currently saved in flash memory during the boot process. Once the CK30 finishes booting, your application appears on the screen.
You need to cold boot the CK30 when an application is locked up and will not respond, when you upgrade the firmware, or when you reflash the computer. The next instructions explain how you warm and cold boot the CK30.
Warm Booting the CK30
If your CK30 does not resume after pressing Power , you may need to warm boot it.
To warm boot the CK30
• Press and hold the Power key for five seconds. The CK30 will tell you it is performing a warm boot and the screen will come back up to the splash screen or your application.
66 CK30 Handheld Computer User’s Manual
Chapter 4 — Troubleshooting and Maintaining the CK30
Cold Booting the CK30
If the CK30 or application is locked up, follow this procedure to perform a cold boot:
To cold boot the CK30
1 Remove the battery.
2 Using a small pointed device (such as the end of a paper clip), press the reset switch on the back side of the CK30.
CK30AA030
1000
Reset switch
3 Replace the battery.
The battery LED on the CK30 will blink three times and the
CK30 will start performing the power on sequence.
Cleaning the Scanner Window and CK30 Screen
To keep the terminal in good working order, you may need to perform these minor maintenance tasks:
• Clean the scanner window.
• Clean the CK30screen.
CK30 Handheld Computer User’s Manual 67
Chapter 4 — Troubleshooting and Maintaining the CK30
Clean the scanner window and CK30 screen as often as needed for the environment in which you are using the terminal. To clean the CK30, use a solution of ammonia and water.
There are no user-serviceable parts inside the terminal.
Opening the unit will void the warranty and may cause damage to the internal components.
Attention: La terminal ne contient pas de pièces révisibles par l’utilisateur. Le fait d’ouvrir l’unité annule la garantie et peut endommager les pièces internes.
To clean the scanner window and terminal screen
1 Press Power to turn off the CK30.
2 Dip a clean towel or rag in the ammonia solution and wring out the excess solution. Wipe off the scanner window and
CK30 screen. Do not allow any abrasive material to touch these surfaces.
3 Wipe dry.
68 CK30 Handheld Computer User’s Manual
A
Appendix
Chapter A — Appendix
Physical and Environmental Specifications
Use the tables in this section to locate technical information about the CK30 and its available features and options.
Physical Dimensions
Length: 20.3 cm (8.0 in)
Width:
Depth:
Weight:
8.9 cm (3.5 in)
5.5 cm (2.15 in), 6.2 cm (2.45 in) with large bottom enclosure
476 g (16.8 oz)
Power Specifications
Operating: Rechargeable 2200 mAh lithium-ion battery
Backup: Super Cap supplying 10 minutes bridge time while the main battery is replaced
Electrical Specifications
Models: CK30A, CK30B, CK30C
Electrical rating: 12VDC at XXX mA
Temperature and Humidity Specifications
Operating temperature: 0°C to 50°C (32°F to 122°F)
Operating humidity: 10 to 90% non-condensing
Storage temperature:
Storage humidity:
-20°C to 60°C (-4°F to 140°F)
0 to 95% relative humidity, noncondensing
Screen Specifications
• 160 x 160 pixels
• 3.12 inch diagonal square active area
• Contrast: eight settings
• CK30A, CK30B: electroluminescent backlight with on/off control
• CK30C: LED backlight with high and low settings
70 CK30 Handheld Computer User’s Manual
Chapter A — Appendix
Keypad Options
• 42-key large numeric and function keypad, available with programmable, international, 3270 TE, 5250 TE, and
VT/ANSI TE overlays
• 50-key full alphanumeric keypad, available with programmable, international, 3270 TE, 5250 TE, and
VT/ANSI TE overlays
• 52-key full alphanumeric keypad, available with programmable, international, 3270 TE, 5250 TE, and
VT/ANSI TE overlays
Accessories for the CK30
You can use these accessories (sold and ordered separately) with the CK30:
AB1 Battery
Use the lithium-ion battery to provide main power to the computer.
AC1 4-Slot Battery Charger
Use the AC1 to charge up to four AB1 batteries at a time. The battery charger is designed to sense when a battery is fully charged and not overcharge it, ensuring long and consistent battery life.
AC2 4-Bay Battery Charging Dock
Use the AC2 to charge up to four AB1 batteries without having to remove them from the CK30. You can insert up to four
CK30s with batteries installed making it easy to remember to charge your batteries overnight.
AD1 Communications Dock
Use the AD1 to charge your AB1 battery and provide power to your CK30 while still having the ability to communicate via a serial, Ethernet, or USB port.
AD2 4-Bay Communications Dock
Use the AD2 to accommodate up to four CK30s with a battery installed. The AD2 dock charges the batteries, provides power to
CK30 Handheld Computer User’s Manual 71
Chapter A — Appendix the computer, and provides a USB and serial port for each inserted CK30.
AG1 Protective Case
The protective case provides a clear vinyl covering to protect the display and keypad area.
AG2 Protective Boot
The protective boot provides additional ruggedness for the
CK30.
AH1 Handle
The handle works with all models of the CK30 and provides a convenient scanning trigger.
AL1 Holster and Belt
The holster and belt provide an easy way for you to carry the
CK30 while not using it. The holster and belt support either right or left-handed use and you can use it with a CK30 with or without a handle.
AL2 Handstrap
The removable and adjustable handstrap make it easy for you to hold and use the CK30 without fatiguing your hand.
AL3 Swiveling Belt Clip
Use the swiveling belt clip to expediently store your CK30 while not in use. Once you have attached the belt clip, it is easy to insert and remove the CK30 as necessary.
AV1 Vehicle Cradle
The vehicle cradle provides protection from vibrations that exceed the level the CK30 can withstand alone.
AA1A Serial Adapter
The serial adapter is a 26-pin dual-row connector to DB-9 connector that connects directly to the bottom of the CK30.
AE1 Power Supply
Provides power to all of the communication docks and chargers.
72 CK30 Handheld Computer User’s Manual
Chapter A — Appendix
Using Hidden Key Sequences
Both the standard and international keypads have hidden key sequences to access special characters not printed on the keypad overlay. Use the following tables to understand how to access these hidden functions on the different versions of the keypads.
Hidden Key Sequences on the Standard Keypads
Press This Key Sequence on One of the Keypads:
To Type: 42-Key 50-Key 52-Key
$
` Green key, F9
!
Green
Green key, G
Green
key,
key,
6
I
Green key, K
'
" Green key, F6
}
{
Green key, F7
Green key, F11
;
:
Green key, F12
Green key, F3
|
Green key, F4
Green key, F8
?
~ Green key, F10
Green
Green
Green
Green
Green
Green
Green
key,
key,
key,
key,
key,
key,
key,
L
N
O
P
Q
R
S
Green key, T
Hidden Key Sequences on the International Keypads
]
[
}
{
Press This Key Sequence on One of the Keypads:
To Type: 42-Key 50-Key 52-Key
$
Green key, a
Green key, b
Green
Green
key,
key,
S
T
Green
Green key, 9
Green
key,
key,
6
0
<
>
Green key, _
Green key, `
Green key, 9
Green key, Tab
CK30 Handheld Computer User’s Manual 73
Chapter A — Appendix
74 CK30 Handheld Computer User’s Manual
Corporate Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
CK30 Handheld Computer User's Manual
*067670-003*
P/N 073528-001
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce