SMART Technologies Meeting Pro 2 Quick Reference Guide
SMART Technologies Meeting Pro 2 is an interactive whiteboard system that enhances collaboration and engagement in meetings and presentations. With its intuitive features, you can easily annotate, share content, and interact with digital resources. Capture ideas, brainstorm visually, and save your work for future reference. The Meeting Pro 2 seamlessly integrates with various software and devices, allowing for versatile use in different settings.
Reklaam
Reklaam
SMART Meeting Pro™
Premium 2.3
Windows® operating systems
System administrator’s guide
Trademark notice
SMART Meeting Pro, the SMART logo, SMART Board, SMART Bridgit, SMART Document Camera, smarttech and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. Windows, DirectX and Internet Explorer are either registered trademarks or trademarks of
Microsoft Corporation in the U.S. and/or other countries. Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the U.S.
and/or other countries. All other third-party product and company names may be trademarks of their respective owners.
Copyright notice
© 2010–2011 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
One or more of the following patents: US6320597; US6326954; US6741267; US7151533; US7757001; USD612396; and USD636784. Other patents pending.
08/2011
i
Installation overview
Task
Ensure your computers meet the minimum requirements.
Obtain the installation packages and supporting files.
Customize the installation packages using SMART Install Manager.
OR
Customize the installation packages using a third-party tool.
Deploy the installation packages.
Reference
OR
L
L I N K S
Please send any feedback on this guide to [email protected]
.
iii
Contents
Installation packages and supporting files
Chapter 2: Customizing installation packages
Chapter 3: Deploying the software
Using the command line interface
Using third-party imaging or remote management software
Activating the software after installation
Chapter 4: Removing the software
Using the command line interface
Using third-party imaging or remote management software
Appendix A: Windows Installer properties and parameters
Appendix B: Language files and codes
Installation language files and codes
Chapter 1:
1
Chapter 1
Getting started
Installation packages and supporting files
This guide explains how to customize and deploy SMART Meeting Pro™ Premium software.
This guide is intended for IT administrators and others experienced with customizing, deploying and administering Windows® software in a networked environment. To use this guide, you must: l
Know IT terminology such as “registry” and “domain controller” l
Know how to complete basic administrative tasks in Windows operating systems such as modifying the registry l
Have administrative privileges and access to servers l
Have Internet access
I
I M P O R T A N T
You must run the commands documented in this guide in an Administrator Command Prompt window. To open an Administrator Command Prompt window, right-click the Command Prompt icon, and then select Run as Administrator.
Computer requirements
Before you install SMART Meeting Pro Premium software, ensure your computers meet the minimum requirements defined in this section.
2
C H A P T E R 1
Getting started
One or two displays
Hardware l
2 GHz dual-core processor or faster (quad-core recommended) l
1 GB of RAM (Windows XP operating system) or 4 GB of RAM (Windows 7 operating system) l
1 GB of free hard disk space (additional free space required during installation) l
10 Mbps network connection (100 Mbps recommended) supporting TCP/IP l
Video cards or motherboard video hardware supporting one or two displays, as needed l
Video card supporting DirectX® technology 9
Software l
Windows XP SP3 or Windows 7 operating systems l
DirectX technology 9 or later l
Internet Explorer® 6.0 or later l
Adobe® Reader® 5 or later
Multiple displays (up to 16)
Hardware l
3 GHz quad-core processor or faster l
4 GB or more of RAM l
1 GB of free hard disk space (additional free space required during installation) l
10 Mbps network connection (100 Mbps recommended) supporting TCP/IP l
Multi-display video cards supporting DirectX technology 9
Software l
Windows XP SP3 or Windows 7 operating systems l
DirectX technology 9 or later l
Internet Explorer 6.0 or later l
Adobe Reader 5 or later
3
C H A P T E R 1
Getting started
Installation packages and supporting files
Before you can customize or deploy SMART software, you must locate the installation packages and supporting files.
Installation packages
There is one installation package (also known as an MSI file) for SMART Meeting Pro Premium software:
Installation package
SMART Meeting Pro Premium software
File name
SMART Meeting Pro Premium.msi
There is one installation package for SMART Product Drivers 10.7 SP1:
Installation package
SMART Product Drivers
File name
SMART Product Drivers Installer.msi
N
N O T E
You need to install SMART Product Drivers only on computers connected to SMART Board™ interactive whiteboards or other SMART interactive products.
Download these installation packages from smarttech.com/administratordownloads .
Save the packages in a location on your network that’s accessible to all computers on which you plan to install the software.
Language files
If you plan to deploy the installation packages in a language other than English (U.S.), ensure the
corresponding MST file for the language is in the same folder as the MSI file (see Installation
language files and codes on page 27).
Similarly, if you want to support handwriting recognition in a language other than English, you must
download and install the appropriate language pack (see Language packs on page 28).
Chapter 2:
Chapter 2
Customizing installation packages
Installing SMART Install Manager
Opening an installation package
Publishing your changes as an MST file
Customizing the SMART Meeting Pro Premium installation package
Customizing the SMART Product Drivers installation package
You can customize installation packages using SMART Install Manager.
OR
You can customize installation packages using third-party tools and Windows Installer properties.
Using SMART Install Manager
SMART Install Manager enables you to customize SMART software installation packages (also known as MSI files) by publishing MST files. You can then deploy the MSI and MST files to computers using third-party imaging or remote management software.
Installing SMART Install Manager
Download and install SMART Install Manager from the SMART Support website.
g To install SMART Install Manager from the website
1. Go to smarttech.com/administratordownloads .
2. Scroll to SMART Meeting Pro software, click Choose a version, and then select SMART
Meeting Pro Premium software > 2.3 for Windows.
5
6
C H A P T E R 2
Customizing installation packages
3. Click Download SMART Install Manager, and then click Download.
4. Save the Install Manager.exe file to your computer.
5. Double-click the Install Manager.exe file.
The SMART Install Manager installation wizard appears.
6. Follow the on-screen instructions.
Using SMART Install Manager
After you install SMART Install Manager, shortcuts to the software appear on the desktop and in the
Start menu under All Programs > SMART Technologies > SMART Install Manager.
With SMART Install Manager, you can do the following: l
Open and customize an installation package.
l
Save your changes to the installation package as an XML file.
l
Publish your changes to the installation packages as an MST file.
Opening an installation package
To customize an installation package, drag its MSI file into the SMART Install Manager window.
Alternatively, you can search for installation packages on your computer by clicking .
N
N O T E
All installation packages you’ve previously opened in SMART Install Manager appear in the
Unmodified Packages tab.
C H A P T E R 2
Customizing installation packages
After you open an installation package, a set of pages for that installation package appears in
SMART Install Manager. Customize the installation package using the controls on these pages.
Saving your changes
After you customize an installation package, save your changes as an XML file by selecting File >
Save As. When you next start SMART Install Manager, load the XML file by selecting File > Open, or by opening the MSI file and then selecting File > Import.
Publishing your changes as an MST file
The final step in using SMART Install Manager to customize an installation package is to publish your changes as an MST file. To do this, select File > Publish, and then use the dialog box to define a location for and create the MST file.
T
T I P
Publish the MST file in the same location as the MSI file.
7
8
C H A P T E R 2
Customizing installation packages
Customizing the SMART Meeting Pro Premium installation package
To customize the SMART Meeting Pro Premium installation package, open the SMART Meeting
Pro Premium.msi file in SMART Install Manager (see Using SMART Install Manager on page 6),
and then set the controls on each page.
Control
Installation Options
Procedure
Installation directory Type the path to your preferred folder for SMART Meeting Pro Premium software.
Product key Type your 22-character product key for SMART Meeting Pro Premium software.
Notes
If you don’t specify a folder, Windows
Installer installs SMART Meeting Pro
Premium software in [Program
files]\SMART
Technologies\SMART Meeting
Pro.
You can type the product key with or without hyphens.
When you type a volume product key, the software activates when you deploy it to your network computers.
Activate SMART
Meeting Pro
Premium during installation
Select to activate SMART Meeting
Pro Premium software automatically during installation rather than manually after installation.
Bridgit Server Information
Bridgit Server Type the name of the
SMART Bridgit™ Server (for example, bridgit.example.com).
The SMART Bridgit Server enables the SMART Meeting Pro Premium software installation to connect to other SMART Meeting Pro Premium software installations. For more information, see smarttech.com/bridgit .
Access Password Type the access password for the
SMART Bridgit Server.
Creation Password Type the creation password for the
SMART Bridgit Server.
Automatically share primary screen
Select this check box to share the main screen each time a user starts a new session.
C H A P T E R 2
Customizing installation packages
Control Procedure Notes
Additional Configuration
E-mail Address
E-mail Server
Type an e-mail address for the
SMART Meeting Pro Premium software installation.
Type the e-mail server for the SMART
Meeting Pro Premium software installation.
Users can e-mail Whiteboard files to themselves or to other users in
SMART Meeting Pro Premium software. When they do so, the software uses this e-mail address in the From field.
Users can e-mail Whiteboard files to themselves or to other users in
SMART Meeting Pro Premium software. When they do so, the software uses this e-mail server to send the file.
Use system e-mail client
Select to use the computer’s default e-mail client to send e-mail messages.
Ink type Select Calligraphic to use calligraphic ink, which smoothes your writing strokes and improves the readability of your notes.
OR
Select Regular to use regular ink.
Shortcuts
Install Desktop shortcut
Launch
SMART Meeting Pro at Startup
Customer Experience
Select to start SMART Meeting Pro
Premium software automatically when the user logs on.
Allow users to participate in the
Customer
Experience Program
Enable the
Customer
Experience Program on all computers
Select to create shortcuts to SMART
Meeting Pro Premium software on the desktop.
Select to allow the user to enable or disable the Customer Experience
Program.
Select to automatically enable the
Customer Experience Program for the user.
When the software first starts, it will ask the user whether he or she wants to participate in the Customer
Experience Program.
9
C H A P T E R 2
Customizing installation packages
Control
Disable the
Customer
Experience Program for all users, but allow users to enable it
Disable the
Customer
Experience Program for all users, and do not allow users to enable it
Procedure Notes
Select to automatically disable the
Customer Experience Program for the user.
The user can enable the Customer
Experience Program through the Help menu.
Select to automatically disable the
Customer Experience Program for the user.
The user can’t enable the Customer
Experience Program through the Help menu.
Customizing the SMART Product Drivers installation package
To customize the SMART Product Drivers installation package, open the SMART Product Drivers
Installer.msi file in SMART Install Manager (see Using SMART Install Manager on page 6), and then
set the controls on each page.
Control
Installation Options
Installation directory
Procedure Notes
Type the path to your preferred folder for SMART Product Drivers.
If you don’t specify a folder,
Windows Installer installs
SMART Product Drivers in
[Program files]\SMART
Technologies\SMART
Product Drivers.
SMART Product Update (SPU) Options
Install SMART Product
Update
Select to install SPU.
Check for updates
Notify users about SMART product updates
Type the number of days (1 to 60) between SPU checks.
Select to notify users of available
SMART product updates through the Windows notification area.
By default, SPU checks for product updates every 30 days.
10
C H A P T E R 2
Customizing installation packages
Control
Driver Installation Options
Install
SMART Document Camera drivers
Install unsigned drivers
Procedure
Select to enable the registration of
SMART Document Camera™ drivers.
Select this check box to enable the registration of unsigned third-party drivers.
Notes
Disable the registration of
SMART Document Camera drivers if they conflict with existing third-party drivers on the computer.
If you enable the registration of unsigned third-party drivers, the installation process could ask users if they trust the makers of the drivers during installation.
This can cause issues if you deploy the installation in Silent mode. Therefore, it’s best to disable the registration of third-party drivers if you deploy the installation in Silent mode.
Post Installation Options: SMART Tools
Start SMART Tools at logon
Select to start SMART Tools when the user logs on.
Post Installation Options: Tablet PC Support
Enable Tablet PC Support Select to use Tablet PC functionality with the SMART Board interactive display without having to connect a Tablet PC.
This property is applicable to
Windows 7 operating system only. It has no effect on other operating systems.
Post Installation Options: SNMP Agent
Start Simple Network
Management Protocol
(SNMP) Agent
Select to enable remote monitoring and control of your SMART products and projectors from a central location using SMART
SNMP Agent.
Using third-party tools
You can customize SMART software installation packages by creating MST files using a third-party
tool, such as Orca database editor, and the Windows Installer properties (see Windows Installer
properties and parameters on page 21).
11
Chapter 3:
Chapter 3
Deploying the software
Using the command line interface
Using third-party imaging or remote management software
Activating the software after installation
You can deploy installation packages using the command line interface.
OR
You can deploy installation packages using third-party imaging or remote management software.
N
N O T E
You might need to manually activate the software after you deploy it.
Using the command line interface
Using the command line interface, you can deploy installation packages in many ways, including running commands from the Command Prompt window and including commands in batch script files.
g To install SMART Meeting Pro Premium software
Run the following command if you created an MST file to customize the installation package: msiexec /i "[Path]\SMART Meeting Pro Premium.msi" TRANSFORMS="[MST
file]" [Parameter]
OR
Run the following command if you didn’t create an MST file to customize the installation package: msiexec /i "[Path]\SMART Meeting Pro Premium.msi" [Properties]
[Parameter]
13
C H A P T E R 3
Deploying the software
Where l
[Path] is the path to the SMART Meeting Pro Premium.msi file and MST file.
l
[MST file] is the name of the MST file.
l
[Properties] is a set of properties you can include to customize the installation (see
SMART Meeting Pro Premium installation package on page 21).
l
[Parameter] is the installation parameter (see Parameters on page 26).
g To install SMART Product Drivers
Run the following command if you created an MST file to customize the installation package: msiexec /i "[Path]\SMART Product Drivers Installer.msi"
TRANSFORMS="[MST file]" [Parameter]
OR
Run the following command if you didn’t create an MST file to customize the installation package: msiexec /i "[Path]\SMART Product Drivers Installer.msi" [Properties]
[Parameter]
Where l
[Path] is the path to the SMART Product Drivers Installer.msi file and MST file.
l
[MST file] is the name of the MST file.
l
[Properties] is a set of properties you can include to customize the installation (see
SMART Product Drivers installation package on page 23).
l
[Parameter] is the installation parameter (see Parameters on page 26).
Using third-party imaging or remote management software
The following procedure shows how to deploy SMART software using Group Policy-based deployment software. For information on deploying SMART software using your organization’s third-party imaging or remote management software, see the software’s documentation.
14
C H A P T E R 3
Deploying the software
N
N O T E
This procedure may vary depending on your version of Windows operating system and your system preferences.
g To deploy an installation package
1. Copy the MSI file and the MST file to \\[Domain Controller]\NETLOGON, where
[Domain Controller] is your domain controller.
2. Open Control Panel, double-click Administrative Tools, and then double-click Active
Directory Users and Computers.
The Active Directory Users and Computers window appears.
3. Right-click your domain, and then select Properties.
The Properties dialog box appears.
4. Click the Group Policy tab, and then click Edit.
The Group Policy Object Editor dialog box appears.
5. Browse to and open Computer Configuration\Software Settings.
6. Right-click Software Installation, select New > Package, and then browse to and select the
MSI file from step 1.
7. In the Deploy Software section, click Advanced, and then click OK.
8. Click the Modifications tab, click Add, and then browse to and select the MST file from step 1.
9. Click OK to apply the MST file to the MSI file.
10. Close all open windows and dialog boxes.
The next time each computer on the domain starts, the computer automatically installs the software in Silent mode with the customizations defined in the MST file.
15
C H A P T E R 3
Deploying the software
Activating the software after installation
There are two situations in which the software doesn’t activate completely: l
Imaging a computer: For the software to activate properly, each computer you install it on must have a unique installation ID. If you use a computer image or clone a hard drive to set up multiple computers, they all have the same installation ID as the original computer, which can cause an activation error.
l
Protecting software for computer configurations: If you use system recovery or protection software, you should activate the software before you lock or freeze the computer for your users. However, if you can’t, you must activate the software afterward.
Run the activation wizard while connected to the network or complete the following procedure to activate the software on each computer.
g To activate SMART Meeting Pro Premium software after installation
Run the following command:
"C:\Program Files\Common Files\SMART Technologies\SMART Product
Update\activationwizard.exe" --puid meeting_pro --m=[Value] --v=1 --a
[Optional flags] --pk [Product key]
Where l
[Value] is 4 to run the activation wizard in unattended mode.
OR
[Value] is 6 to run the activation wizard in user interface mode.
l
[Optional flags] are optional flags you can include to configure the activation wizard.
Flag
-monitor=[Number]
-proxy=[Host:Port]
--
--
-proxyuser=[User] proxypassword=[Password] locale=[Code]
Purpose
Specify the monitor to display the activation wizard.
Specify the proxy host and port number to use for activation.
Specify the proxy user name to use for activation.
Specify the proxy password to use for activation.
Display the activation wizard user interface in a specific language, where [Code] is your language code.
l
[Product key] is the software product key.
16
Chapter 4:
Chapter 4
Removing the software
Using the command line interface
Using third-party imaging or remote management software
You can remove SMART software using the command line interface.
OR
You can remove SMART software using third-party imaging or remote management software.
Using the command line interface
Using the command line interface, you can remove SMART software in many ways, including running commands from the Command Prompt window and including commands in batch script files.
I
I M P O R T A N T
Only remove the common platform after removing all other SMART software.
g To remove SMART Meeting Pro Premium software
Run the following command: msiexec /x "[Path]\SMART Meeting Pro Premium.msi" [Parameter]
Where l
[Path] is the path to the SMART Meeting Pro Premium.msi file.
l
[Parameter] is the installation parameter (see Parameters on page 26).
OR
Run the following command to remove the software using the product code: msiexec /x [Product code] [Parameter]
17
C H A P T E R 4
Removing the software
Where l
[Product code] is the product code for the version of SMART Meeting Pro Premium software you’re removing, including the braces (“{” and “}”).
Version
2.0
2.1
2.2
2.3
Product code
{596BD3B5-DC48-4AD2-A60A-4C39C9852294}
{4BD7F008-CDD9-454D-8A5B-4FF8BB8FEF02}
{76F84A17-835E-46C7-9C31-520BAFD5AC9D}
{E1660294-4C1E-4893-A40D-FFE0051E824F} l
[Parameter] is the installation parameter (see Parameters on page 26).
g To remove SMART Product Drivers
If you installed SMART Product Drivers using the SMART Product Drivers Installer.msi file, run the following command to remove the software using the installation package: msiexec /x "[Path]\SMART Product Drivers Installer.msi" [Parameter]
Where l
[Path] is the path to the SMART Product Drivers Installer.msi file.
l
[Parameter] is the installation parameter (see Parameters on page 26).
OR
Run the following command to remove the software using the product code: msiexec /x [Product code] [Parameter]
Where l
[Product code] is the product code for the version of SMART Product Drivers you’re removing, including the braces (“{” and “}”).
Version
10.0.124.0
10.0.131.0
10.0.163.1
10.0.165.1
10.0.186.2
Product code
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
18
C H A P T E R 4
Removing the software
Version
10.0.188.3
10.0.232.4
10.0.255.5
10.0.314.5
10.0.392.6
10.0.528.7
10.0.532.7
10.6.48.0
10.6.106.1
10.6.175.2
10.7.81.0
10.7 SP1
10.8
Product code
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{FF7A64AB-214A-47D1-95E7-742BCBA7F6C9}
{00C68967-9790-40DA-86F7-FDB248A5CDB1}
{AA9C1126-50DD-4993-9CDC-0BED8167293C}
{984EAE92-6043-451A-B786-9327FF165310}
{2623A1E3-478A-4F4A-A522-3A3D784A0C9C}
{487F1117-8BDE-4518-A798-015172AE0410}
{333B0B76-FC96-4C51-9AF6-B6EFA15ACE99}
{1355416A-967D-47C5-823D-D493C3E0B97C}
{4CE6C6E8-0DAD-4757-86ED-7FB4035BA98B}
{67E6410C-1E97-4D03-BEC2-8E83323A6BBD} l
[Parameter] is the installation parameter (see Parameters on page 26).
g To remove the common platform
If you installed the common platform using the SMART Product Drivers Installer.msi file, run the following command to remove the software using the installation package: msiexec /x "[Path]\SMART Product Drivers Installer.msi" [Parameter]
Where l
[Path] is the path to the SMART Product Drivers Installer.msi file.
l
[Parameter] is the installation parameter (see Parameters on page 26).
OR
Run the following command to remove the common platform using the product code: msiexec /x {0E5DD7A3-BE29-430C-970B-C553F4A58C39} [Parameter]
Where [Parameter] is the installation parameter (see Parameters on page 26).
g To remove SMART Product Drivers and the common platform
Run the following command: msiexec /x "[Path]\SMART Product Drivers Installer.msi" [Parameter]
19
C H A P T E R 4
Removing the software
Where l
[Path] is the path to the SMART Product Drivers Installer.msi file.
l
[Parameter] is the installation parameter (see Parameters on page 26).
Using third-party imaging or remote management software
The following procedure shows how to remove SMART software using Windows operating systems’
Group Policy-based deployment software. For information on removing software using your organization’s third-party imaging or remote management software, see the software’s documentation.
N
N O T E
This procedure may vary depending on your version of Windows operating system and your system preferences.
g To remove a deployed installation package
1. Open Control Panel, double-click Administrative Tools, and then double-click Active
Directory Users and Computers.
The Active Directory Users and Computers window appears.
2. Right-click your domain, and then select Properties.
The Properties dialog box appears.
3. Click the Group Policy tab, and then click Edit.
The Group Policy Object Editor dialog box appears.
4. Browse to and open Computer Configuration\Software Settings\
Software Installation.
5. Right-click the software you want to remove, and then select All Tasks > Remove.
6. Select Immediately uninstall the software from users and computers, and then click OK.
The next time each computer on the domain starts, the computer automatically removes the software.
20
Appendix A:
21
Appendix A
Windows Installer properties and parameters
SMART Meeting Pro Premium installation package
SMART Product Drivers installation package
Properties
SMART Meeting Pro Premium installation package
The following are properties for the SMART Meeting Pro Premium installation package:
Property
General properties
INSTALLDIR
ISX_
SERIALNUM
ACTIVATE_
LICENSE
Allowed values
[String]: The path to your preferred folder for SMART Meeting Pro
Premium software.
[String]: The 22-character product key you received from SMART.
1 (default): Register the product key and automatically activate the software.
[Empty string]: Register the product key but don’t automatically activate the software.
Notes
If you don’t specify a folder, Windows
Installer installs SMART Meeting Pro
Premium software in [Program
files]\SMART
Technologies\SMART Meeting Pro.
This property automatically populates the Product Key box in the activation wizard if you choose not to include the
ACTIVATE_LICENSE property.
You must include the
ISX_SERIALNUM property for this property to work.
For mass activation information, see
A P P E N D I X A
Windows Installer properties and parameters
Property Allowed values
TRANSFORMS [String]: A language MST file for the
installation (see Installation language
Notes
Ensure the specified MST file is in the same folder as the MSI file.
This property defines the language of the installer’s user interface and the installed software’s icons and shortcuts. It doesn’t define the installed software’s user interface language. The installed software uses the computer’s operating system language if it’s supported, or English
(U.S.) if not.
You can also use the TRANSFORMS property to apply an MST file created
by SMART Install Manager (see page
SMART Meeting Pro Premium software properties
BRIDGIT_
SERVER_NAME
[String]: The name of the
SMART Bridgit Server (for example,
bridgit.example.com).
The SMART Bridgit Server enables the SMART Meeting Pro Premium software installation to connect to other SMART Meeting Pro Premium software installations. For more information, see smarttech.com/bridgit .
SERVER_PWD [String]: The access password for
SMART Bridgit Server.
CREATION_
PWD
[String]: The creation password for
SMART Bridgit Server.
ENABLEBRIDGIT
AUTOSHARING_
REG
1 (default): Share the main screen each time a user starts a new session.
0: Don’t share the main screen each time a user starts a new session.
EMAIL_
ADDRESS
[String]: An e-mail address for the
SMART Meeting Pro Premium software installation.
EMAIL_SERVER [String]: An e-mail server for the
SMART Meeting Pro Premium software installation (for example,
mail.example.com).
Users can e-mail Whiteboard files to themselves or to other users in
SMART Meeting Pro Premium software. When they do so, the software uses this e-mail address in the From field.
Users can e-mail Whiteboard files to themselves or to other users in
SMART Meeting Pro Premium software. When they do so, the software uses this e-mail server to send the file.
22
A P P E N D I X A
Windows Installer properties and parameters
Property
USE_SYSTEM_
USE_
CALLIGRAPHIC_
INK
CREATE_
DESKTOPICONS
CREATE_
STARTUPICON
CUSTOMER_
LOGGING
Allowed values
1 (default): Use the computer’s default e-mail client to send e-mail messages.
0: Don’t use the computer’s default email client to send e-mail messages.
1 (default): Use calligraphic ink, which smoothes your writing strokes and improves the readability of your notes.
0: Use regular ink.
1 (default): Include a shortcut to the software on the desktop.
[Empty string]: Don’t include a shortcut to the software on the desktop.
1 (default): Start SMART Meeting Pro
Premium software when the user logs on.
[Empty string]: Don’t start SMART
Meeting Pro Premium software when the user logs on.
0: Disable the Customer Experience
Program.
1 (default): Allow the user to enable or disable the Customer Experience
Program.
2: Enable the Customer Experience
Program.
3: Disable the Customer Experience
Program and don’t allow the user to enable it.
Notes
SMART Product Drivers installation package
The following are properties for the SMART Product Drivers installation package:
Notes Property Allowed values
General properties
INSTALLDIR [String]: The path to your preferred folder for SMART Product Drivers.
If you don’t specify a folder, Windows
Installer installs
SMART Product Drivers in [Program
files]\SMART Technologies\SMART
Product Drivers.
23
A P P E N D I X A
Windows Installer properties and parameters
Property Allowed values
TRANSFORMS [String]: A language MST file for the
installation (see Installation language
Notes
Ensure the specified MST file is in the same folder as the MSI file.
This property defines the language of the installer’s user interface and the installed software’s icons and shortcuts. It doesn’t define the installed software’s user interface language. The installed software uses the computer’s operating system language if it’s supported, or English
(U.S.) if not.
You can also use the TRANSFORMS property to apply an MST file created
by SMART Install Manager (see page
SPU properties
INSTALL_SPU
SPU_TIME_
FRAME
1 (default): Install SPU.
0: Don’t install SPU.
[Integer]: The time in days (1 to 60) between SPU checks.
By default, SPU checks for product updates every 30 days.
This property is applicable only if you install SPU.
This property is applicable only if you install SPU.
PRODUCT_
NOTIFICATION
1 (default): Notify the user when updates are available from SPU.
0: Don’t notify the user when updates are available from SPU.
SMART Product Drivers properties
INSTALL_
DOCCAM_
DRIVERS
LOSU_
BRDTOOLS
1 (default): Enable the registration of
SMART Document Camera drivers.
0: Disable the registration of
SMART Document Camera drivers.
1 (default): Start
SMART Product Drivers after the installation.
[Empty string]: Don’t start
SMART Product Drivers after the installation.
Disable the registration of
SMART Document Camera drivers if they conflict with existing third-party drivers on the computer.
24
A P P E N D I X A
Windows Installer properties and parameters
Property Allowed values
ENABLE_
STPCS
1 (default): Use Tablet PC functionality with the SMART Board interactive whiteboard without connecting a Tablet PC.
[Empty string]: Don’t use Tablet PC functionality with the SMART Board interactive whiteboard without connecting a Tablet PC.
START_
SNMP_SERVICE
1: Enable SMART SNMP Agent, allowing you to remotely monitor and control your SMART products and projectors from a central location.
[Empty string] (default): Disable
SMART SNMP Agent.
INSTALL_
UNSIGNED_
DRIVERS
1: Enable the registration of unsigned third-party drivers.
0 (default): Disable the registration of unsigned third-party drivers.
Notes
This property is applicable to Windows
7 operating system only. It has no effect on other operating systems.
If you specify [Null], users don’t have touch support at the Windows logon screen.
If you enable the registration of unsigned third-party drivers, the installation process could ask users if they trust the makers of the drivers during installation. This can cause issues if you deploy the installation in
Silent mode. Therefore, it’s best to disable the registration of third-party drivers if you deploy the installation in
Silent mode.
25
A P P E N D I X A
Windows Installer properties and parameters
Parameters
The following are the standard Windows Installer parameters for the msiexec command.
Parameter
/q
/qb
/qb!
/qb+
/qb+!
/qr
/qf
/qn
/qn+
Use
Hide the installation wizard.
N
N O T E
This is Silent mode.
Show a basic installation wizard.
Show a basic installation wizard without a Cancel button.
Show a basic installation wizard with a dialog box signaling the end of the installation.
Show a basic installation wizard without a Cancel button but with a dialog box signaling the end of the installation.
Show a reduced installation wizard.
Show the full installation wizard, including a dialog box signaling the end of the installation or the Fatal Error, User Exit or Exit dialog box.
Hide the installation wizard and the dialog box signaling the end of the installation.
Hide the installation wizard but show the dialog box signaling the end of the installation.
26
Appendix B:
27
Appendix B
Language files and codes
Installation language files and codes
Installation language files and codes
Language
English (U.S.)
English (UK)
Chinese (Simplified)
Czech
Danish
Dutch
French (France)
German
Italian
Japanese
Norwegian
Portuguese (Portugal)
Portuguese (Brazil)
Russian
Spanish (Spain)
Spanish (Mexico)
Swedish
Turkish
1041
1044
2070
1046
1049
1034
2058
1053
1055
Code
1033
2057
2052
1029
1030
1043
1036
1031
1040
1041.mst
1044.mst
2070.mst
1046.mst
1049.mst
1034.mst
2058.mst
1053.mst
1055.mst
File
1033.mst
2057.mst
2052.mst
1029.mst
1030.mst
1043.mst
1036.mst
1031.mst
1040.mst
A P P E N D I X B
Language files and codes
Language packs
File chinese_(simplified)_language_ pack.msi
czech_language_pack.msi
danish_language_pack.msi
dutch_language_pack.msi
english_(united_kingdom)_language_ pack.msi
Code
{C42566AD-8B6D-42DA-AB32-AB0FF4DA4835}
{65F93E53-1BF8-42CC-B34E-ADE8F38A5DDD}
{35F9BB11-C3B1-4E54-BCF6-A816219E8816}
{2F24F27E-3137-4A0E-8D1D-B3A203FBEB21}
{660B0281-20C5-4FC9-A249-40C860262435} french_language_pack.msi
german_language_pack.msi
italian_language_pack.msi
japanese_language_pack.msi
norwegian_language_pack.msi
portuguese_(portugal)_language_ pack.msi
{AB4FDB88-2330-4703-A529-BF8AD553755C}
{6BE163A5-1987-4789-96C4-9F5B481A0B09}
{48B115BA-5E2B-4DB2-B1E2-9C0A1DBF8405}
portuguese_(brazil)_language_pack.msi {F1FF65A8-EC0C-43A4-8E4E-154EEBF4C081} russian_language_pack.msi
{441D1F4B-0DAD-4600-B17B-7F8880E4F9B4} spanish_language_pack.msi
spanish_(international_latin_american)_ language_pack.msi
swedish_language_pack.msi
turkish_language_pack.msi
{42EA3C50-D781-4408-A6BC-650E4EAA42B6}
{FBD1D659-DFDF-4EFC-9E6E-187CF498380C}
{337225D9-28B9-41BC-8157-57FF543D82E8}
{0EEE7AD9-6FB8-4837-8C87-E187D817D5AB}
{AC4EFF6B-076D-4307-AF29-EA2D23575773}
{6F22C4C4-D6F9-4E73-AFCA-93570FC12DCC}
{C3F1AFA6-DCFA-4DA3-AA28-F4770D4B4FA8}
28
Index
A
activation
B
Bridgit Server See SMART Bridgit Server browsers See web browsers
C
checklist
Chinese command line interface computer imaging computer requirements
Customer Experience Program
Czech
D
Danish desktop icons
DirectX document
See SMART Document
Camera
camera downloads drivers
SMART Document Camera
SMART Product unsigned
Dutch
E
e-mail addresses
29 e-mail server
English
F
French
G
German
H
I
hard disk space
imaging
Install Manager installation overview
Internet Explorer
Italian
J
Japanese
L
See SMART Install
Manager
language files language setup
M
MSI files
I N D E X
MST files
N
Norwegian
O
overview
P
parameters passwords
Portuguese prerequisites knowledge product key protection software
R
RAM requirements
Russian
S
serial number sharing shortcuts
Silent mode
SMART Bridgit Server
SMART Document Camera
SMART Install Manager about
See product key
downloading installing using
SMART Product Update
SNMP
Spanish
30 startup
Swedish system recovery software
T
Tablet PC support third-party applications
Turkish
U
unsigned drivers
W
web browsers
Windows 7 operating system
Windows Installer
Windows operating systems
X
XML
SMART Technologies smarttech.com/support smarttech.com/contactsupport
Laadi alla
Avalik link on uuendatud
Teie vestluse avalik link on uuendatud. You may view and manage your chat links after registration here.
Dokumendi avalik link
Reklaam