advertisement
ARCLED7307HD
LED PROJECTOR
Manuale Utente
User Manual
IT EN
Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.
La riproduzione - anche parziale - per propri scopi commerciali è vietata.
Al fine di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modificare, in qualunque momento e senza preavviso, le specifiche menzionate nel presente manuale di istruzioni.
Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it
REV.001-04/13
ARCLED7307HD
INDICE Sicurezza
Avvertenze generali
Attenzioni e precauzioni per l’installazione
Informazioni generali
1 Introduzione
1. 1 Descrizione
1. 2 Specifiche tecniche
1. 3 Elementi di comando e di collegamento
2 Installazione
2. 1 Montaggio
3 Funzioni e impostazioni
3. 1 Funzionamento
3. 2 Impostazione base
3. 3 Struttura menu
3. 4 Funzionamento in modalità automatica
3. 5 Modalità Master/Slave
3. 6 Collegamento
3. 7 Configurazione canali DMX
3. 8 Modalità DMX
3. 9 Impostazione dell'indirizzo di start
3. 10 Collegamenti della linea DMX
3. 11 Costruzione del terminatore DMX
3. 12 Tabella canali DMX
3. 13 Configurazione Static
3. 14 Editing programmi personalizzati
3. 15 Funzioni speciali
3. 16 Calibrazione
3. 17 Attivazione password
4 Manutenzione
4. 1 Manutenzione e pulizia del sistema ottico
4. 2 Risoluzione dei problemi
5 Appendice
5. 1 Vista esplosa
Certificato di garanzia
Contenuto dell'imballo:
• ARCLED7307HD
• Staffa di fissaggio (2pz.)
• Cavo di sicurezza
• Manuale utente
3
9
15
19
19
19
20
12
12
12
13
14
21
10
10
11
11
12
12
22
22
23
6
6
8
4
4
5
4
ARCLED7307HD
ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.
SICUREZZA
Avvertenze generali
• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e pertanto recano la sigla .
• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.
• È obbligatorio effettuare il collegamento ad un impianto di alimentazione dotato di un’efficiente messa a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di interruttori differenziali opportunamente dimensionati.
• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere effettuate da un installatore elettrico qualificato. Verificare che frequenza e tensione della rete corrispondono alla frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.
• L’unità non per uso domestico, solo per uso professionale.
• Evitare di utilizzare l’unità:
- in luoghi soggetti a vibrazioni, o a possibili urti;
- in luoghi a temperatura superiore ai 45°C oppure a -20°C.
• Evitare che nell’unità penetrino liquidi infiammabili, acqua o oggetti metallici.
• Non smontare e non apportare modifiche all’unità.
• Tutti gli interventi devono essere sempre e solo effettuati da personale tecnico qualificato. Rivolgersi al più vicino centro di assistenza tecnica autorizzato.
• Se si desidera eliminare il dispositivo definitivamente, consegnarlo per lo smaltimento ad un’istituzione locale per il riciclaggio.
Attenzioni e precauzioni per l’installazione
• Se il dispositivo dovesse trovarsi ad operare in condizioni differenti da quelle descritte nel presente manuale, potrebbero verificarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.
• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete di alimentazione.
• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qualsiasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel paese di utilizzo.
• Installare l’unità in un luogo ben ventilato.
• Mantenere i materiali infiammabili ad una distanza di sicurezza dall’unità.
• I filtri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro efficienza.
• I LED devono essere sostituiti se danneggiati o termicamente deformati.
• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono provocare attacchi d’epilessia presso persone fotosensibili o epilettiche.
• Non collegare il proiettore a un dimmer pack.
ARCLED7307HD
5
INFORMAZIONI GENERALI
Spedizioni e reclami
Le merci sono vendute “franco nostra sede” e viaggiano sempre a rischio e pericolo del distributore/cliente. Eventuali avarie e danni dovranno essere contestati al vettore. Ogni reclamo per imballi manomessi dovrà essere inoltrato entro 8 giorni dal ricevimento della merce.
Garanzie e resi
Il prodotto è coperto da garanzia in base alle vigenti normative. Sul sito www.musiclights.it è possibile consultare il testo integrale delle “Condizioni Generali di Garanzia”. Si prega, dopo l’acquisto, di procedere alla registrazione del prodotto sul sito www.musiclights.it. In alternativa il prodotto può essere registrato compilando e inviando il modulo riportato alla fine del manuale. A tutti gli effetti la validità della garanzia
è avallata unicamente dalla presentazione del certificato di garanzia. Music & Lights constata tramite verifica sui resi la difettosità dichiarata, correlata all’appropriato utilizzo, e l’effettiva validità della garanzia; provvede quindi alla riparazione dei prodotti, declinando tuttavia ogni obbligo di risarcimento per danni diretti o indiretti eventualmente derivanti dalla difettosità.
6
ARCLED7307HD
- 1 - INTRODUZIONE
1.1 DESCRIZIONE
L’ ARCLED7307HD è stato disegnato per essere la versione “compact” del popolare fratello maggiore
ARCLED7314, che negli anni si è affermato essere un vero standard sul mercato.
Equipaggiato con 7x3W CREE LED RGB/FullColor e con un design lenti identico alla versione 7314,
ARCLED7307HD rappresenta una soluzione complementare ed adatta per offrire un prodotto di performance professionali anche in applicazioni con budget limitati.
Le dimensioni ipercompatte di ARCLED7307 ed il design il aluminio pressofuso e vetro temperato (IP66), rendono questo proiettore un prodotto ideale per il Rental e versatile per qualsiasi applicazione in concerti, illuminazione architetturale, luce d’accento e fiere.
1.2 SPECIFICHE TECNICHE
Sorgente luminosa e ottica
• 7 x 3W CREE LED RGB/FC ad alta resa luminosa
• Lumen: 561
• Lux@2m: 1212@2m
• Peak intensity: 4837cd
• Diodi LED ad alta efficienza, con colori più vividi e minore assorbimento energetico delle lampade tradizionali
• Sistema di sintesi colore: miscelazione RGB/FullColor (>16 milioni di colori) per possibilità cromatiche illimitate
• Preset temperatura colore bianco: 3200K~10000K
• Ottiche installate: 16°
• Angolo di proiezione fascio: 17°
• Angolo di campo: 32°
• Durata media diodi LED: >50.000 ore
Funzionamento ed elettronica
• Diverse configurazioni DMX disponibili (3, 4, 5, 10, 13 canali) per controllo avanzato o semplificato
- 3 canali: RGB
- 3 canali: HSV
- 4 canali: RGB, dimmer
- 5 canali: RGB, dimmer, strobe
- 9 canali: RGB, dimmer, macro, strobe, auto programs, programs speed, dimmer curve, ID address
- 13 canali: RGB, RGB fine, dimmer, dimmer fine, macro, strobe, auto programs, programs speed, dimmer curve, ID address
• Valori dimmer e colori a risoluzione 16bit
• Interfaccia di controllo mediante display LED per esecuzione dei programmi automatici, scelta dei colori statici, memorizzazione di show personalizzati, calibrazione preset colori
• Regolazione curva dimmer: 5 configurazioni selezionabili
• Modalità Master/Slave con più unità collegate
• Passaggio lineare “step less” dei valori sui canali DMX
• Frequenza dei diodi anti-flicker (>400Hz)
• Silenziosità di funzionamento, proiettore privo di ventole e struttura disegnata per avere una dissipazione a convezione
ARCLED7307HD
Corpo e alimentazione
• Corpo in alluminio ad alta resistenza progettato per facilitare la dissipazione termica
• Pannello frontale: realizzato in vetro temperato
• Grado di isolamento: IP66 (IP) - IP54 (TZ)
• Bilanciamento temperatura e pressione attraverso valvole di sfiato GORE micro-forate
• Adattatori di alimentazione (shuko) e segnale (xlr-3p) inclusi
• Doppia staffa per il fissaggio in sospensione e per il posizionamento del proiettore da terra
• Alimentazione: 100-240V 50/60Hz
• Condizioni di esercizio: -40/45°
• Output alimentazione per connessione di più unità in serie: fino a 48 proiettori a 230V
• Consumo ad emissione massima: 27W
• Peso: 3,2 kg
• Dimensioni (LxAxP): 175x220x258 mm
7
220
Fig.1
228
Diagramma di luminosità
16°
0m
2.0m
1212lx
4.0m
303lx
6.0m
134lx
8.0m
75lx
10.0m
48lx
0.58m
1.17m
1.76m
2.34m
2.93m
Lux Center Beam Angle: 16.7° Beam Width
Fig.2
8
ARCLED7307HD
1.3 ELEMENTI DI COMANDO E DI COLLEGAMENTO
4
6
3
7
5
1
2
1. STAFFA DI MONTAGGIO
2. MANOPOLA DI FISSAGGIO per la staffa di montaggio
3. PANNELLO DI CONTROLLO con display e 4 pulsanti per accesso e gestione delle diverse funzioni.
4. DMX IN (XLR a 3 poli):
1 = massa, 2 = DMX -, 3 = DMX +
5. DMX OUT (XLR a 3 poli):
1= massa, 2 = DMX -, 3 = DMX +
6. POWER IN (connettore di potenza Neutrik) per il collegamento ad una presa di rete (100-240V
50/60Hz) tramite il cavo rete in dotazione.
7. POWER OUT (connettore di potenza Neutrik): output alimentazione per connessione di più unità in serie: fino a 50 proiettori a 220V.
Fig.3
ARCLED7307HD
9
- 2 - INSTALLAZIONE
2.1 MONTAGGIO
L’ ARCLED7307HD può essere collocato su un piano solido. Inoltre, grazie alle possibilità di fissaggio sulla doppia staffa (fig.4), l’unità può essere montata anche a testa in giù, su una traversa. Per il fissaggio occorrono dei supporti robusti per il montaggio. L’area di collocazione deve avere una stabilità sufficiente e supportare almeno 10 volte il peso dell’unità.
Inoltre assicurarsi di rispettare tutte le avvertenze in materia di sicurezza.
• Fissare il proiettore attraverso l’apposita staffa (1) ad una collocazione idonea.
• È assolutamente necessario assicurare il proiettore contro la caduta utilizzando un cavo di sicurezza: in particolare collegare il cavo in un punto adatto in modo che la caduta del proiettore non possa superare i 20 cm.
• Orientare il proiettore intervenendo, se necessario, sulla manopola della staffa di montaggio (2).
1
2
Fig.4
10
ARCLED7307HD
- 3 - FUNZIONI E IMPOSTAZIONI
3.1 FUNZIONAMENTO
Per accendere l’ ARCLED7307HD, inserire la spina del cavo di alimentazione in una presa di rete (100-240V
50/60Hz). L’unità può essere comandata da un unità DMX di comando luce oppure svolgere autonomamente il suo programma. Per spegnere l’ ARCLED7307HD, staccare la spina dalla presa di rete. Per maggiore comodità è consigliabile collegare l’unità con una presa comandata da un interruttore.
3.2 IMPOSTAZIONE BASE
Il proiettore ARCLED7307HD dispone di un LED display e 4 pulsanti per accesso alle funzioni del pannello di controllo (fig.5).
Fig.5
MENU
Per scorrere il menu principale o tornare ad una opzione del menu precedente
ENTER
Per entrare nel menu selezionato o confermare il valore attuale della funzione o l'opzione all'interno di un menu
UP
Per scorrere attraverso le diverse funzioni in ordine discendente o aumentare il valore della funzione stessa
DOWN
Per scorrere attraverso le diverse funzioni in ordine ascendente o diminuire il valore della funzione stessa
ARCLED7307HD
11
3.3 STRUTTURA MENU
STAT
AUTO
RUN dMX
PERS
EDIT
SET
CAL
(Password:
UP-DOWN
UP-DOWN)
KEY
RED
GREN
BLUE
STRB
AT.01 ÷ AT.10
PR.01 ÷ PR.10
dMX / SLAVE d.(001-512)
R.(000-255)
G.(000-255) b.(000-255)
S.(0-20)
TOUR / TR16 / ARC.1 / AR1.d / AR1.S / HSV
PR.01 ÷ PR.10
SC.01
...
SC.30
RED, GREN,
BLUE, STRB,
TIME, FADE
UPLd
REST
COLO dIMX
CURV
DERR
SLCK
STRB
****
****
OFF/ RGBw / UC
DIM4 / DIM1 / DIM2 / DIM3 / OFF
OFF / CV1 / CV2 / CV3
SAVE/ BLAK
OFF/ON
SPEC/CLAS
SEND
REST
CAL1 wT.01 ÷ wT.11
****
CAL2
CALR
RGBw
****
ON/OFF
R.(000-255), G.(000-255), b.(000-255), S.(0-20), T.(000-255),
F.(000-255)
OK
OK
R.(000-255)
G.(000-255) b.(000-255)
R.(000-255)
G.(000-255) b.(000-255)
OK
3.4 FUNZIONAMENTO IN MODALITÀ AUTOMATICA
Se alla presa DMX non è presente alcun segnale di comando DMX, l’unità può svolgere il suo programma
Show autonomamente:
• Premere il tasto MENU fino a quando sul display non appare [AUTO], quindi premere il tasto ENTER per confermare la scelta.
• Premere il tasto UP/DOWN per scorrere al programma desiderato da 1 a 10 (AT.01 - AT.10 o PR.01 - PR.10).
L’unità entrerà in modalità automatica mandando in esecuzione il programma selezionato.
IMPORTANTE - I programmi AT.01 - AT.10 sono completamente pre-programmati e non possono subire essere modificati. Invece, i programmi PR.01 - PR.10 possono essere modificati nella modalità EDIT.
NOTA - Nella modalità automatica l’unità è MASTER.
12
ARCLED7307HD
3.5 MODALITÀ MASTER/SLAVE
Questa modalità consente di collegare in linea più unità ARCLED7307HD senza un controller. La prima unità sarà impostata come master e le altre funzioneranno come slave con lo stesso effetto.
• Premere il tasto MENU fino a quando sul display non appare [RUN], quindi premere il tasto ENTER per confermare la scelta.
• Premere il tasto UP/DOWN e selezionare [SLAV] per impostare le unità come slave.
• Sull’unità MASTER selezionare il programma desiderato come indicato nel paragrafo 3.4
• Servirsi dei connettori DMX dell’ARCLED7307HD e di un cavo XLR per formare una catena di unità.
In certe condizioni e lunghezze si consiglia di effettuare una terminazione come mostrato a pagina 14.
3.6 COLLEGAMENTO
Si possono collegare più unità affinché tutte le unità secondarie abbiano lo stesso effetto luce dell’unità principale (Master).
1. Collegare l’uscita DMX OUT dell’unità principale con l’ingresso DMX IN della prima unità secondaria servendosi di un cavo XLR a 3 poli.
2. Collegare l’uscita DMX OUT della prima unità secondaria con l’ingresso DMX IN della seconda unità secondaria ecc.
3.7 CONFIGURAZIONI CANALI DMX
L’ ARCLED7307HD dispone di 6 configurazioni dei canali DMX a cui si può accedere dal pannello di controllo.
• Premere il tasto MENU fino a quando sul display non appare [PERS], quindi premere il tasto ENTER.
• Attraverso il tasto UP/DOWN selezionare la configurazione dei canali DMX che si desidera [TOUR - TR16 -
ARC.1 - AR1.d - AR1.s - HSV]
Le tabelle a pagina 15 indicano le modalità di funzionamento e i relativi valori DMX. Come interfaccia
DMX, l’unità possiede dei contatti XLR a 3 poli.
3.8 MODALITÀ DMX
• Per poter entrare nella modalità DMX; premere il tasto MENU fino a quando sul display non appare
[RUN], quindi premere il tasto ENTER.
• Premere il tasto UP/DOWN e selezionare la modalità [DMX].
• Dal menu iniziale, per impostare il valore desiderato, entrare nella modalità [dMX] e selezionare il valore desiderato [001-512]; tenere premuto per lo scorrimento veloce.
• Al termine dell’impostazione il valore verrà salvato automaticamente
NOTA - Quando il dispositivo opera nella modalità automatica la funzione [RUN] non è disponibile.
3.9 IMPOSTAZIONE DELL’INDIRIZZO DI START
Per poter comandare l’ ARCLED7307HD con un’unità di comando luce, occorre impostare l’indirizzo di start DMX per il primo canale DMX. Se, per esempio, sull’unità di comando è previsto l’indirizzo 33 per comandare la funzione del primo canale DMX, si deve impostare sull’ ARCLED7307HD l’indirizzo di start
33. Le altre funzioni del pannello saranno assegnate automaticamente agli indirizzi successivi. Segue un esempio con indirizzo 33 di start e una configurazione a 13 canali DMX:
Numero canali DMX
13
Indirizzo di start (esempio)
33
Indirizzo DMX occupati
33-45
Prossimo indirizzo di start possibile per unità n°1
46
Prossimo indirizzo di start possibile per unità n°2
59
Prossimo indirizzo di start possibile per unità n°3
72
DMX Address: 33 DMX Address: 46
ARCLED7307HD
DMX Address: 59 DMX Address: 72
13
. . . . . . . . . . . .
DMX512 Controller
Esempio di configurazione a 13 canali DMX (modalità TR16)
Fig.6
3.10 COLLEGAMENTI DELLA LINEA DMX
La connessione DMX è realizzata con connettori standard XLR. Utilizzare cavi schermati, 2 poli ritorti, con impedenza 120Ω e bassa capacità.
Per il collegamento fare riferimento allo schema di connessione riportato di seguito:
DMX - INPUT
Spina XLR
DMX - OUTPUT
Presa XLR
Pin1 : Massa - Schermo
Pin2 : - Negativo
Pin3 : + Positivo
Fig.7
ATTENZIONE
La parte schermata del cavo (calza) non deve mai essere collegata alla terra dell’impianto; ciò comporterebbe malfunzionamenti delle unità e dei controller.
Per passaggi lunghi può essere necessario l’inserimento di un amplificatore DMX.
In tal caso, è sconsigliato utilizzare nei collegamenti cavo bilanciato microfonico poiché non è in grado di trasmettere in modo affidabile i dati di controllo DMX.
• Collegare l’uscita DMX del controller con l’ingresso DMX della prima unità;
• Collegare, quindi, l’uscita DMX con l’ingresso DMX della successiva unità; l’uscita di quest’ultima con l’ingresso di quella successiva e via dicendo finchè tutte le unità sono collegate formando una catena.
• Per installazioni in cui il cavo di segnale deve percorrere lunghe distanze è consigliato inserire sull’ultima unità una terminazione DMX.
14
ARCLED7307HD
3.11 COSTRUZIONE DEL TERMINATORE DMX
La terminazione evita la probabilità che il segnale DMX 512, una volta raggiunta la fine della linea stessa venga riflesso indietro lungo il cavo, provocando, in certe condizioni e lunghezze, la sua sovrapposizione al segnale originale e la sua cancellazione.
La terminazione deve essere effettuata, sull’ultima unità della catena, con connettori XLR a 3 pin, saldando una resistenza di 120Ω (minimo 1/4W) tra i terminali 2 e 3, così come indicato in figura.
Fig.8
Esempio: connettore XLR a 3 pin
ARCLED7307HD
3.12 TABELLA CANALI DMX
TOUR
Ch Function in TOUR mode
1
2
3
4
5
6
Value
MASTER DIMMER
000 - 100% 000 - 255
RED
(CH7 select CUSTOM 01-10, CH2 CONTROL TIME) 000 - 255
GREEN
(CH7 select CUSTOM 01-10, CH3 CONTROL FADE) 000 - 255
BLUE
000 - 100% 000 - 255
COLOR MACRO+WHITE BALANCE
No function
Red 100%/Green Up/Blue 0%
Red Down/Green 100%/Blue 0%
Red 0%/Green 100%/Blue Up
Red 0%/Green Down/Blue 100%
Red Up/Green 0%/Blue100%
Red 100%/Green 0%/Blue Down
Red 100%/Green Up/Blue Up
Red Down/Green Down/Blue 100%
All LEDs 100%
White 1: 3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
SPECIAL STROBE
No strobe
Strobe (slow to fast)
No strobe
Lightning strobe (slow to fast)
No strobe
Random strobe (slow to fast)
CLASSIC STROBE
0Hz
1Hz
000 - 009
010 - 099
100 - 109
110 - 179
180 - 189
190 - 255
000 - 009
010 - 019
171 - 200
201 - 205
206 - 210
211 - 215
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
000 - 010
011 - 030
031 - 050
051 - 070
071 - 090
091 - 110
111 - 130
131 - 150
151 - 170
Ch Function in TOUR mode
6
7
AUTO
No function
AUTO 01
AUTO 02
AUTO 03
AUTO 04
AUTO 05
AUTO 06
AUTO 07
AUTO 08
AUTO 09
AUTO 10
CUSTOM 01
CUSTOM 02
CUSTOM 03
CUSTOM 04
CUSTOM 05
CUSTOM 06
CUSTOM 07
CUSTOM 08
CUSTOM 09
13Hz
14Hz
15Hz
16Hz
17Hz
8Hz
9Hz
10Hz
11Hz
12Hz
2Hz
3Hz
4Hz
5Hz
6Hz
7Hz
18Hz
19Hz
20Hz
15
Value
020 - 029
030 - 039
040 - 049
050 - 059
060 - 069
070 - 079
080 - 089
090 - 099
100 - 109
110 - 119
120 - 129
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 189
190 - 199
200 - 255
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
181 - 190
191 - 200
201 - 210
211 - 220
000 - 020
021 - 030
031 - 040
041 - 050
051 - 060
061 - 070
071 - 080
081 - 090
091 - 100
16
Ch Function in TOUR mode
7
8
9
CUSTOM 10
No function
AUTO SPEED
Since the walking speed (slow to fast)
DIMMER SPEED
Return settings
Normal
DIM1
DIM2
DIM3
DIM4
Value
221 - 220
221 - 255
000 - 255
000 - 009
010 - 029
030 - 069
070 - 129
130 - 189
190 - 255
ARCLED7307HD
TR16
Ch Function in TR16 mode
1 MASTER DIMMER
Value
000 - 255
2 MASTER DIMMER FINE
3
4
000 - 255
RED
(CH11 select CUSTOM 01-10, CH3 CONTROL TIME) 000 - 255
RED FINE
(CH11 select CUSTOM 01-10, CH4 CONTROL FADE) 000 - 255
5 GREEN 000 - 255
6 GREEN FINE
7 BLUE
8 BLUE FINE
9
10
COLOR MACRO+WHITE BALANCE
No function
Red 100%/Green Up/Blue 0%
Red Down/Green 100%/Blue 0%
Red 0%/Green 100%/Blue Up
Red 0%/Green Down/Blue 100%
Red Up/Green 0%/Blue100%
Red 100%/Green 0%/Blue Down
Red 100%/Green Up/Blue Up
Red Down/Green Down/Blue 100%
All LEDs 100%
White 1: 3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
SPECIAL STROBE
No strobe
Strobe (slow to fast)
000 - 255
000 - 255
000 - 255
000 - 010
011 - 030
031 - 050
051 - 070
071 - 090
091 - 110
111 - 130
131 - 150
151 - 170
171 - 200
201 - 205
206 - 210
211 - 215
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
000 - 009
010 - 099
ARCLED7307HD
17
CH Function in TR16 mode
10
11
AUTO
No function
AUTO 01
AUTO 02
AUTO 03
AUTO 04
AUTO 05
AUTO 06
AUTO 07
AUTO 08
AUTO 09
AUTO 10
CUSTOM 01
CUSTOM 02
CUSTOM 03
CUSTOM 04
14Hz
15Hz
16Hz
17Hz
18Hz
19Hz
20Hz
9Hz
10Hz
11Hz
12Hz
13Hz
4Hz
5Hz
6Hz
7Hz
8Hz
0Hz
1Hz
2Hz
3Hz
No strobe
Lightning strobe (slow to fast)
No strobe
Random strobe (slow to fast)
CLASSIC STROBE
Value
100 - 109
110 - 179
180 - 189
190 - 255
090 - 099
100 - 109
110 - 119
120 - 129
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 189
190 - 199
200 - 255
000 - 009
010 - 019
020 - 029
030 - 039
040 - 049
050 - 059
060 - 069
070 - 079
080 - 089
000 - 020
021 - 030
031 - 040
041 - 050
051 - 060
061 - 070
071 - 080
081 - 090
091 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
Ch Function in TR16 mode
11
12
13
CUSTOM 05
CUSTOM 06
CUSTOM 07
CUSTOM 08
CUSTOM 09
CUSTOM 10
No function
AUTO SPEED
Since the walking speed (slow to fast)
DIMMER SPEED
Return settings
Normal
DIM1
DIM2
DIM3
DIM4
000 - 255
000 - 009
010 - 029
030 - 069
070 - 129
130 - 189
190 - 255
Value
161 - 170
181 - 190
191 - 200
201 - 210
211 - 220
221 - 220
221 - 255
18
ARC.1
CH Function in ARC.1
1 RED 0 - 100%
2 GREEN 0 - 100%
3 BLUE 0 - 100%
AR1.d
CH Function in AR1.d
1 MASTER DIMMER
2 RED 0 - 100%
3 GREEN 0 - 100%
4 BLUE 0 - 100%
AR1.S
CH Function in AR1.S
1 MASTER DIMMER
2 RED 0 - 100%
3 GREEN 0 - 100%
4 BLUE 0 - 100%
5 STROBE
Value
000 - 255
000 - 255
000 - 255
000 - 255
Value
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
ARCLED7307HD
Value
000 - 255
000 - 255
000 - 255
HSV
CH Function in HSV
1 HUE 0 - 100%
2 SATURATION 0 - 100%
3 VALUE 0 - 100%
Value
000 - 255
000 - 255
000 - 255
ARCLED7307HD
19
3.13 CONFIGURAZIONE STATIC
Per impostare il bilanciamento personalizzato del rosso, verde e blu.
• Premere il tasto MENU per entrare nel menu principale, quindi premere il tasto UP/DOWN fino a quando sul display non appare [STAT], quindi premere il tasto ENTER.
• Selezionare il canale rosso, verde o blu (RED - GREN -BLUE) attraverso i tasti UP/DOWN.
• Per confermare premere il tasto ENTER.
• Impostare i valori (000 - 255), attraverso i tasti UP/DOWN.
• Infine, impostare il valore [STRB] tra (0 - 20) mediante i tasti UP/DOWN.
3.14 EDITING PROGRAMMI PERSONALIZZATI
Per effettuare le modifiche dei programmi personalizzati procedere come segue:
• Premere il tasto MENU fino a quando sul display non appare [EDIT], quindi premere il tasto ENTER per confermare la scelta.
• Premere il tasto UP o DOWN per selezionare il programma da modificare da 1 a 10 [PR.01- PR.10].
• Per ogni programma è possibile modificare 30 scene, intervenendo sui valori del canale rosso [RED], verde [GREN], blu [BLUE] modificando i valori della funzione strobo [STRB 00-20], time [TIME 000-255] e fade
[FADE 000-255].
• I valori (ad esempio 000 - 255) possono essere selezionati attraverso il tasto UP/DOWN.
3.15 FUNZIONI SPECIALI
• Premere il tasto MENU e selezionare la voce [SETTINGS]; per confermare premere il tasto ENTER.
È possibile accedere alle seguenti funzioni:
NOTA - Le impostazioni di fabbrica relative alla password di accesso corrispondono alla combinazione dei tasti UP + DOWN + UP + DOWN. Premere ENTER per confermare.
UPLOAD
• Selezionando la funzione [UPLd] è possibile caricare i programmi personalizzati dalla unità corrente
Master alle unità Slave. Per eseguire il trasferimento è necessario inserire la password che risulta essere la stessa per l’accesso principale.
RESET
Selezionando la funzione [REST] è possibile ripristinare i valori di default.
COLOR
Selezionando la funzione [COLO] è possibile attivare/disattivare le modalità calibratura colore.
- Quando [RGB TO W] è selezionato, su RGB =255, 255, 255 il colore è visualizzato come calibrato nella modalità CALIB2 (RGB TO W). Quando [COLOR] è impostato su [OFF], su RGB =255, 255, 255 il colore non può essere regolato e l’uscita mostrerà la massima potenza.
- Quando [UC] è selezionato, i colori sono regolati secondo un preset universale standard.
DIMMER
Selezionando la funzione [dIM] è possibile entrare nella modalità dimmer. In particolare, quando è impostato su [OFF], l’RGBWA e il MASTER DIMMER sono lineari. Dim1/2/3/4 rappresentano invece diversi valori di velocità nella modalità non lineare; [DIM1] è il valore più veloce mentre [DIM4] il più lento.
NOTA - Le impostazioni di fabbrica sono su [DIM4].
20
ARCLED7307HD
CURV
Selezionare la funzione [CURV], per regolare la forma della curva dimmer. Far riferimento al grafico riportato di seguito (fig.9) per la caratteristica di ciascuna curva.
CURV dimming
1: OFF
2: CV1
3: CV3
4: CV4
Fig.9
DERR
Selezionare la funzione [DERR], per la gestione in caso di errore del segnale DMX.
- [SAVE] consente di salvare gli ultimi dati DMX in caso di errore del segnale DMX.
- [BLACK] consente di attivare la modalità blackout in caso di errore DMX.
SLCK
• Selezionando la funzione [SLCK] è possibile attivare o disattivare la password di accesso al menu di impostazioni.
• Selezionare [ON] o [OFF] a seconda che si voglia, rispettivamente, abilitare o disabilitare la password.
Quando l’unità è impostata su ON, bisognerà immettere la password per accedere al menu impostazioni.
STRB
• Il proiettore ARCLED7307HD dispone di due differenti impostazioni della strobo: CLAS strobo e SPEC strobo. Tali impostazioni sono valide sono nelle seguenti configurazioni DMX: Tour, AR2.S e TR16.
3.16 CALIBRAZIONE
• Premere il tasto MENU e selezionare attraverso i tasti direzionali la voce [CAL]; inserire la password di accesso corrispondente alla combinazione dei tasti UP + DOWN + UP + DOWN. Premere ENTER per confermare.
IMPOSTAZIONI BIANCO
Per impostare il bilanciamento personalizzato della temperatura colore bianco:
• Premere il tasto MENU, quindi premere il tasto UP/DOWN fino a quando sul display non appare
[CAL1], poi premere il tasto ENTER.
• Selezionare uno delle 11 impostazioni colore bianco pre-programmate (WHITE01 - WHITE11).
ARCLED7307HD
21
• Le impostazioni possono essere modificate, intervenendo sui valori (000 - 255) relativi ai canali rosso, verde e blu (Red - Green - Blue), attraverso i tasti UP/DOWN.
CALIBRAZIONE BIANCO
Per impostare il bilanciamento del bianco intervenendo sui parametri RGB:
• Premere il tasto MENU, quindi premere il tasto UP/DOWN fino a quando sul display non appare
[CAL2], poi premere il tasto ENTER.
• Selezionare il canale rosso, verde, blu attraverso il tasto UP/DOWN.
• Per confermare premere il tasto ENTER
• Impostare i valori 000 - 255 attraverso i tasto UP/DOWN
Quando la nuova impostazione è attivata, l’unità di controllo DMX sceglierà RGB=255, 255, 255 il colore bianco verrà fatto dagli attuali valori RGB nella modalità [CAL2]
3.17 ATTIVAZIONE PASSWORD
Per attivare/disattivare la password di accesso:
• Premere il tasto MENU e selezionare [KEY], quindi premere il tasto ENTER.
• Selezionare [ON] oppure [OFF] a seconda che si voglia, rispettivamente, attivare o disattivare la password di accesso.
Quando l’unità è impostata su ON, dopo 30 secondi o al prossimo riavvio bisognerà immettere la password per l’accesso menu di controllo.
NOTA - Le impostazioni di fabbrica relative alla password di accesso corrispondono alla combinazione dei tasti UP+DOWN+UP+DOWN. Premere ENTER per confermare.
22
ARCLED7307HD
- 4 - MANUTENZIONE
4.1 MANUTENZIONE E PULIZIA DEL SISTEMA OTTICO
• Durante gli interventi, assicurarsi che l’area sotto il luogo di installazione sia libera da personale non qualificato.
• Spegnere l’unità, scollegare il cavo di alimentazione ed aspettare finché l’unità non si sia raffreddata.
• Tutte le viti utilizzate per l’installazione dell’unità e le sue parti devono essere assicurate saldamente e non devono essere corrose.
• Alloggiamenti, elementi di fissaggio e di installazione (soffitto, truss, sospensioni) devono essere totalmente esenti da qualsiasi deformazione.
• I cavi di alimentazione devono essere in condizione impeccabile e devono essere sostituiti immediatamente nel momento in cui anche un piccolo problema viene rilevato.
• Si dovrebbe procedere, ad intervalli regolari, alla pulizia della parte frontale per asportare polvere, fumo e altre particelle. Solo così, la luce può essere irradiata con la luminosità massima. Per la pulizia usare un panno morbido, pulito e un detergente per vetri come si trovano in commercio. Quindi asciugare le parti delicatamente.
Attenzione: consigliamo che la pulizia interna sia eseguita da personale qualificato!
4.2 RISOLUZIONE DEI PROBLEMI
Anomalie
Il proiettore non illumina
Bassa intensità di luce generale
Il proiettore non è alimentato
Il proiettore non risponde al
DMX
•
•
Possibili cause
•
•
•
•
•
•
•
•
•
•
•
Mancanza di alimentazione di rete
Dimmer impostato a 0
Tutti i colori impostati a 0
LED difettoso/i
Scheda LED difettosa
Lenti sporche
Lente disallineata
Mancanza di alimentazione di rete
Cavo di alimentazione danneggiato
Alimentatore interno difettoso
Indirizzamento DMX errato
Cavo di segnale DMX difettoso
Rimbalzo segnale DMX
Controlli e rimedi
•
•
•
•
•
•
•
•
•
•
•
•
•
Verificare la presenza della tensione alimentazione
Incrementare i valori del canale dimmer
Incrementare i valori dei canali colori
Sostituire scheda LED
Sostituire scheda LED
Pulire il dispositivo regolarmente
Installare il gruppo ottico correttamente
Verificare la presenza della tensione alimentazione
Controllare il cavo di alimentazione
Sostituire l'alimentatore interno
Controllare il pannello di controllo e l'indirizzamento delle unità
Controllare il cavo di segnale DMX
Installare una terminazione DMX come suggerito
Rivolgersi a un centro di assistenza tecnico autorizzato in caso di problema non riportato in tabella o che non possono essere risolti mediante la procedura riportata in tabella.
ARCLED7307HD
- 5 - APPENDICE
5.1 VISTA ESPLOSA
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
17
Fig.10
18
19
20
21
22
No ITEM
1 Rubber B
2 Glass
3 3 in 1 lens frame front cover
4
LED3 in 1 lens
5
6
3 in 1 lens frame back cover
LED board
7
8
9
10
11
Thermal switch
Thermal switch holder
Power supply
Adaptor PCB
Driver board
No ITEM
12 Display board
13
Button pressed plate
14
15
16
17
Display screen lens
Display board rubber
Rubber C
XLR 3 cores socket (male)
18
19
20
21
22
XLR 3 cores socket (female)
PS socket (male)
PS socket (male)
Rubber A
Adjusting stainless steel knob
23
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
ARCLED7307HD
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
General information
1 Introduction
1. 1 Description
1. 2 Technical specifications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 Operation in automatic mode
3. 5 Master/Slave mode
3. 6 Linking
3. 7 DMX configuration
3. 8 DMX mode
3. 9 DMX addressing
3. 10 Connection of the DMX line
3. 11 Construction of the DMX termination
3. 12 DMX control
3. 13 Static configuration
3. 14 Editing custom programs
3. 15 Special functions
3. 16 Calibration functions
3. 17 Activate the password
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Trouble shooting
5 Appendix
5. 1 Exploded view
Warranty
Packing content
• ARCLED7307HD
• Mount bracket (2pc.)
• Safety cable
• User manual
1
7
13
17
17
17
17
10
10
10
11
12
19
8
9
9
8
9
10
20
20
21
4
4
6
2
2
3
2
ARCLED7307HD
WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with cure for future reference. It contains important information about the installation, usage and maintenance of the unit.
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are therefore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modifications on the unit not described in this instruction manual, otherwise you will risk an electric shock.
• Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualified electrical installer. Check that the main frequency and voltage correspond to those for which the unit is designed as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the fixture under the following conditions:
- in places subject to vibrations or bumps;
- in places with a temperature of over 45°C or -20°C.
• Make certain that no inflammable liquids, water or metal objects enter the fixture.
• Do not dismantle or modify the fixture.
• All work must always be carried out by qualified technical personnel. Contact the nearest sales point for an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way different to the one described in this manual, it may suffer damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut off power from the main supply.
• Always additionally secure the projector with the safety rope. When carrying out any work, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country in which the fixture’s being used.
• Install the fixture in a well ventilated place.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Keep any inflammable material at a safe distance from the fixture.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Never connect the product to a dimmer pack.
ARCLED7307HD
3
GENERAL INFORMATION
Shipments and claims
The goods are sold “ex works” and always travel at the risk and danger of the distributor. Eventual damage will have to be claimed to the freight forwarder. Any claim for broken packs will have to be forwarded within 8 days from the reception of the goods.
Warranty and returns
The guarantee covers the fixture in compliance with existing regulations. You can find the full version of the “General Guarantee Conditions” on our web site www.musiclights.it. Please remember to register the piece of equipment soon after you purchase it, logging on www.musiclights.it. The product can be also registered filling in and sending the form available on your guarantee certificate. For all purposes, the validity of the guarantee is endorsed solely on presentation of the guarantee certificate. Music & Lights will verify the validity of the claim through examination of the defect in relation to proper use and the actual validity of the guarantee. Music & Lights will eventually provide replacement or repair of the products declining, however, any obligation of compensation for direct or indirect damage resulting from faultiness.
4
ARCLED7307HD
- 1 - INTRODUCTION
1.1 DESCRIPTION
ARCLED7307HD has been conceived to be the “compact” version of its popular big brother ARCLED7314, which has become a real standard in the range of LED spotlight.
ARCLED7307 is equipped with 7x3W CREE RGB/FullColor LEDs combined with same optic design of 7314 version, representing a complementary fixture of its bigger version and to introduce an high-quality tool even in range of small lighters.
Its super-compact sizes and the construction made by die-cast aluminium housing with tempered glass
(IP66) makes ARCLED7307HD an essential product for the Rental stock, and useful for application in concerts, architectural lightings, accent lightings and corporate events.
1.2 TECHNICAL SPECIFICATIONS
Light source and optics
• 7 x 3W high-efficiency CREE RGB/FC LEDs
• Lumen: 561
• Lux@2m: 1212@2m
• Peak intensity: 4837cd
• Energy-saving LEDs employed, with more vivid colours and lower power consumption than traditional lamps
• Colour synthesis: RGB FullColor mixing (>16 million colours) for a limitless colour range
• White temperature presets: 3200K~10000K
• Installed optics: 16°
• Beam angle: 17°
• Field angle: 32°
• LEDs average life span: >50’000h
Electronics and features
• Several DMX selectable configurations (3, 4, 5, 10, 13 channels) for advanced or basic controlling
- 3 channels: RGB
- 3 channels: HSV
- 4 channels: RGB, dimmer
- 5 channels: RGB, dimmer, strobe
- 9 channels: RGB, dimmer, macro, strobe, auto programs, programs speed, dimmer curve, ID address
- 13 channels: RGB, RGBfine, dimmer, dimmer fine, macro, strobe, auto programs, programs speed, dimmer curve, ID address
• 16bit dimming and colour calibration
• LED display user interface for auto programs execution, static colour mode, creation of custom shows, colour calibration presets
• 5 different dimming available curves
• Master/Slave mode for stand-alone operations
• Linear and “stepless” transition between DMX values
• Flicker-free operations (400Hz)
• Silent operations, due to natural cooling of the peculiar chassis and to absence of fans
Structure and power supply
• Sturdy die-cast aluminium body conceived for long-time durability and demanding applications
• Frontal tempered glass panel
ARCLED7307HD
• Internal Protection: IP67 (IP) - IP54 (TZ)
• Pressure and temperature balance through GORE membrane vents
• Power (shuko) and data (xlr-3p) adapter cables included
• Double hanging bracket suitable for safe hanging and for floor positioning
• Power unit: 100-240V 50/60Hz
• Power output to link more units in a chain: up to 24 fixtures at 230V
• Max power consumption: 27W
• Weight: 3,2 kg
• Dimensions (WxHxD): 175x220x258 mm
5
220
Fig.1
228
Photometric data
16°
0m
2.0m
1212lx
4.0m
303lx
6.0m
134lx
8.0m
75lx
10.0m
48lx
0.58m
1.17m
1.76m
2.34m
2.93m
Lux Center Beam Angle: 16.7° Beam Width
Fig.2
6
ARCLED7307HD
1.3 OPERATING ELEMENTS AND CONNECTIONS
4
6
3
7
5
1
2
1. MOUNTING BRACKET
2. LOCKING KNOB for the mounting bracket.
3. CONTROL PANEL with display and 4 button used to access the control panel functions and manage them.
4. DMX IN (3-pole XLR):
1 = ground, 2 = DMX -, 3 = DMX +
5. DMX OUT (3-pole XLR):
1= ground, 2 = DMX -, 3 = DMX +
6. POWER IN (Neutrik connector) for connection to a socket (100-240V~/50-60Hz) via the supplied mains cable.
7. POWER OUT (Neutrik connector): power output for connection of multiple units in series: 50 units may be connected in serie
(220V)
Fig.3
ARCLED7307HD
7
- 2 - INSTALLATION
2.1 MOUNTING
ARCLED7307HD may be set up on a solid and even surface. The unit can also be mounted upside down to a cross arm. For fixing, stable mounting clips are required. The mounting place must be of sufficient stability and be able to support a weight of 10 times of the unit’s weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country in which the fixture’s being used.
• Install the projector at a suitable location by means of the mounting bracket (1).
• Always additionally secure the projector with the safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.
• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the bracket if is necessary.
1
2
Fig.4
8
ARCLED7307HD
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation and can be operated via a DMX controller or it independently performs its show program in succession.
To switch off, disconnect the mains plug from the socket. For a more convenient operation it is recommended to connect the unit to a socket which can be switched on and off via a light switch.
3.2 BASIC
Access control panel functions using the four panel buttons located directly underneath the LED Display
(fig.5).
Fig.5
MENU
Used to access the menu or to return a previous menu option
ENTER
Used to select and store the current menu or confirm the current function value or option within a menu
UP
Navigates upwards through the menu list and decreases the numeric value when in a function
DOWN
Navigates downwards through the menu list and increases the numeric value when in a function
ARCLED7307HD
9
3.3 MENU STRUCTURE
STAT
AUTO
RUN dMX
PERS
EDIT
SET
CAL
(Password:
UP-DOWN
UP-DOWN)
KEY
RED
GREN
BLUE
STRB
AT.01 ÷ AT.10
PR.01 ÷ PR.10
dMX / SLAVE d.(001-512)
R.(000-255)
G.(000-255) b.(000-255)
S.(0-20)
TOUR / TR16 / ARC.1 / AR1.d / AR1.S / HSV
PR.01 ÷ PR.10
SC.01
...
SC.30
RED, GREN,
BLUE, STRB,
TIME, FADE
UPLd
REST
COLO dIMX
CURV
DERR
SLCK
STRB
****
****
OFF/ RGBw / UC
DIM4 / DIM1 / DIM2 / DIM3 / OFF
OFF / CV1 / CV2 / CV3
SAVE/ BLAK
OFF/ON
SPEC/CLAS
SEND
REST
CAL1 wT.01 ÷ wT.11
****
CAL2
CALR
RGBw
****
ON/OFF
R.(000-255), G.(000-255), b.(000-255), S.(0-20), T.(000-255),
F.(000-255)
OK
OK
R.(000-255)
G.(000-255) b.(000-255)
R.(000-255)
G.(000-255) b.(000-255)
OK
3.4 OPERATION IN AUTOMATIC MODE
If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show programme provided that the blackout mode is switched off:
• Press the button MENU so many times until the display shows [AUTO], then press the button ENTER.
• Press the button UP/DOWN to switch between the programs (AUTO 01 - AUTO10 o CUSTOM01 - CUSTOM10). The unit will operate in automatic mode.
NOTE - Programs AUTO 01 - AUTO10 are fully pre-programmed and will not be altered by changes in EDIT mode. Programs CUSTOM01 - CUSTOM10 are fully pre-programmed and can be edited in EDIT mode.
In automatic mode the unit will be set as Master.
10
ARCLED7307HD
3.5 MASTER/SLAVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the first unit in line; other units will work as slave with the same effect.
• Press the button MENU so many times until the display shows [RUN], and press the button ENTER to confirm.
• Press UP/DOWN to set the unit as [SLAVE].
• Select the desired program (see section 3.4).
• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the units. For longer cable runs we suggest a terminator at the last fixture (see page 12).
3.6 LINKING
Several units may be interconnected in order to control all further slave units to the same effect of the master unit.
1. Connect the DMX OUT of the master unit via 3 -pole XLR cable to the DMX IN of the first slave unit.
2. Connect the DMX OUT of the first slave unit to the DMX IN of the second slave unit, etc. until all units are connected in a chain.
3.7 DMX CONFIGURATION
ARCLED7307HD is equipped with 6 DMX configuration.
• Press the button MENU so many times until shows [PERS], and press the button ENTER to confirm.
• Select the desired DMX configuration [TOUR - TR16 - ARC.1 - AR1.d - AR1.s - HSV] through the buttons UP/
DOWN.
The tables on page 13 indicate the operating mode and DMX value. The ARCLED7307HD is equipped with
3 -pole XLR connections.
3.8 DMX MODE
• Press the button MENU so many times until the display shows [RUN], and press the button ENTER to confirm.
• Press the buttons UP and DOWN to select [DMX] mode.
• Then enter the [ADDRESS] mode to set the ID address.
• Press the buttons UP and DOWN to select the desired value [001-512].
• After the setting value is automatically saved.
NOTE - When fixtures are under Auto program operation, the [RUN] mode does no works.
3.9 DMX ADDRESSING
To able to operate the ARCLED7307HD with a light controller, adjust the DMX start address for the first a
DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the first DMX channel, adjust the start address 33 on the ARCLED7307HD. The other functions of the light effect panel are then automatically assigned to the following addresses.
An example with the start address 33 is shown below:
Number of
DMX channels
13
Start address
(example)
33
DMX Address occupied
33-45
Next possible start address for unit No. 1
46
Next possible start address for unit No. 2
59
Next possible start address for unit No. 3
72
DMX Address: 33 DMX Address: 46
ARCLED7307HD
DMX Address: 59 DMX Address: 72
11
DMX512 Controller
Example 13 DMX channels configuration (TR16 mode)
Fig.6
. . . . . . . . . . . .
3.10 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω impedance and low capacity.
The following diagram shows the connection mode:
DMX - INPUT
XLR plug
DMX - OUTPUT
XLR socket
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Fig.5
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would cause faulty fixture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplifier.
For those connections the use of balanced microphone cable is not recommended because it cannot transmit control DMX data reliably.
• Connect the controller DMX input to the DMX output of the first unit.
• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input of the following unit until all the units are connected in chain.
• When the signal cable has to run longer distance is recommended to insert a DMX termination on the last unit.
12
ARCLED7307HD
3.11 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reflected back along the cable when they reaches the end of the line: under certain conditions and with certain cable lengths, this could cause them to cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR connector, as shown in figure.
Fig.6
Example:
3 pin XLR connector
ARCLED7307HD
3.12 DMX CONTROL
TOUR
Ch Function in TOUR mode
1
2
3
4
5
6
Value
MASTER DIMMER
000 - 100% 000 - 255
RED
(CH7 select CUSTOM 01-10, CH2 CONTROL TIME) 000 - 255
GREEN
(CH7 select CUSTOM 01-10, CH3 CONTROL FADE) 000 - 255
BLUE
000 - 100% 000 - 255
COLOR MACRO+WHITE BALANCE
No function
Red 100%/Green Up/Blue 0%
Red Down/Green 100%/Blue 0%
Red 0%/Green 100%/Blue Up
Red 0%/Green Down/Blue 100%
Red Up/Green 0%/Blue100%
Red 100%/Green 0%/Blue Down
Red 100%/Green Up/Blue Up
Red Down/Green Down/Blue 100%
All LEDs 100%
White 1: 3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
SPECIAL STROBE
No strobe
Strobe (slow to fast)
No strobe
Lightning strobe (slow to fast)
No strobe
Random strobe (slow to fast)
CLASSIC STROBE
0Hz
1Hz
000 - 009
010 - 099
100 - 109
110 - 179
180 - 189
190 - 255
000 - 009
010 - 019
171 - 200
201 - 205
206 - 210
211 - 215
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
000 - 010
011 - 030
031 - 050
051 - 070
071 - 090
091 - 110
111 - 130
131 - 150
151 - 170
Ch Function in TOUR mode
6
7
AUTO
No function
AUTO 01
AUTO 02
AUTO 03
AUTO 04
AUTO 05
AUTO 06
AUTO 07
AUTO 08
AUTO 09
AUTO 10
CUSTOM 01
CUSTOM 02
CUSTOM 03
CUSTOM 04
CUSTOM 05
CUSTOM 06
CUSTOM 07
CUSTOM 08
CUSTOM 09
13Hz
14Hz
15Hz
16Hz
17Hz
8Hz
9Hz
10Hz
11Hz
12Hz
2Hz
3Hz
4Hz
5Hz
6Hz
7Hz
18Hz
19Hz
20Hz
13
Value
020 - 029
030 - 039
040 - 049
050 - 059
060 - 069
070 - 079
080 - 089
090 - 099
100 - 109
110 - 119
120 - 129
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 189
190 - 199
200 - 255
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
181 - 190
191 - 200
201 - 210
211 - 220
000 - 020
021 - 030
031 - 040
041 - 050
051 - 060
061 - 070
071 - 080
081 - 090
091 - 100
14
Ch Function in TOUR mode
7
8
9
CUSTOM 10
No function
AUTO SPEED
Since the walking speed (slow to fast)
DIMMER SPEED
Return settings
Normal
DIM1
DIM2
DIM3
DIM4
Value
221 - 220
221 - 255
000 - 255
000 - 009
010 - 029
030 - 069
070 - 129
130 - 189
190 - 255
ARCLED7307HD
TR16
Ch Function in TR16 mode
1 MASTER DIMMER
Value
000 - 255
2 MASTER DIMMER FINE
3
4
000 - 255
RED
(CH11 select CUSTOM 01-10, CH3 CONTROL TIME) 000 - 255
RED FINE
(CH11 select CUSTOM 01-10, CH4 CONTROL FADE) 000 - 255
5 GREEN 000 - 255
6 GREEN FINE
7 BLUE
8 BLUE FINE
9
10
COLOR MACRO+WHITE BALANCE
No function
Red 100%/Green Up/Blue 0%
Red Down/Green 100%/Blue 0%
Red 0%/Green 100%/Blue Up
Red 0%/Green Down/Blue 100%
Red Up/Green 0%/Blue100%
Red 100%/Green 0%/Blue Down
Red 100%/Green Up/Blue Up
Red Down/Green Down/Blue 100%
All LEDs 100%
White 1: 3200K
White 2: 3400K
White 3: 4200K
White 4: 4900K
White 5: 5600K
White 6: 5900K
White 7: 6500K
White 8: 7200K
White 9: 8000K
White 10: 8500K
White 11: 10000K
SPECIAL STROBE
No strobe
Strobe (slow to fast)
000 - 255
000 - 255
000 - 255
000 - 010
011 - 030
031 - 050
051 - 070
071 - 090
091 - 110
111 - 130
131 - 150
151 - 170
171 - 200
201 - 205
206 - 210
211 - 215
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
000 - 009
010 - 099
ARCLED7307HD
15
CH Function in TR16 mode
10
11
AUTO
No function
AUTO 01
AUTO 02
AUTO 03
AUTO 04
AUTO 05
AUTO 06
AUTO 07
AUTO 08
AUTO 09
AUTO 10
CUSTOM 01
CUSTOM 02
CUSTOM 03
CUSTOM 04
14Hz
15Hz
16Hz
17Hz
18Hz
19Hz
20Hz
9Hz
10Hz
11Hz
12Hz
13Hz
4Hz
5Hz
6Hz
7Hz
8Hz
0Hz
1Hz
2Hz
3Hz
No strobe
Lightning strobe (slow to fast)
No strobe
Random strobe (slow to fast)
CLASSIC STROBE
Value
100 - 109
110 - 179
180 - 189
190 - 255
090 - 099
100 - 109
110 - 119
120 - 129
130 - 139
140 - 149
150 - 159
160 - 169
170 - 179
180 - 189
190 - 199
200 - 255
000 - 009
010 - 019
020 - 029
030 - 039
040 - 049
050 - 059
060 - 069
070 - 079
080 - 089
000 - 020
021 - 030
031 - 040
041 - 050
051 - 060
061 - 070
071 - 080
081 - 090
091 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
Ch Function in TR16 mode
11
12
13
CUSTOM 05
CUSTOM 06
CUSTOM 07
CUSTOM 08
CUSTOM 09
CUSTOM 10
No function
AUTO SPEED
Since the walking speed (slow to fast)
DIMMER SPEED
Return settings
Normal
DIM1
DIM2
DIM3
DIM4
000 - 255
000 - 009
010 - 029
030 - 069
070 - 129
130 - 189
190 - 255
Value
161 - 170
181 - 190
191 - 200
201 - 210
211 - 220
221 - 220
221 - 255
16
ARC.1
CH Function in ARC.1
1 RED 0 - 100%
2 GREEN 0 - 100%
3 BLUE 0 - 100%
AR1.d
CH Function in AR1.d
1 MASTER DIMMER
2 RED 0 - 100%
3 GREEN 0 - 100%
4 BLUE 0 - 100%
AR1.S
CH Function in AR1.S
1 MASTER DIMMER
2 RED 0 - 100%
3 GREEN 0 - 100%
4 BLUE 0 - 100%
5 STROBE 2
Value
000 - 255
000 - 255
000 - 255
000 - 255
Value
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
ARCLED7307HD
Value
000 - 255
000 - 255
000 - 255
HSV
CH Function in HSV
1 HUE 0 - 100%
2 SATURATION 0 - 100%
3 VALUE 0 - 100%
Value
000 - 255
000 - 255
000 - 255
ARCLED7307HD
17
3.13 STATIC CONFIGURATION
To set the custom balance of red, blue and green:
• Press the button MENU, then press the button UP/DOWN so many times until the display shows [STAT].
Press the button ENTER to confirm.
• Select the color red, green or blue (RED - GREN -BLUE) through the buttons UP and DOWN and then press the button ENTER.
• Set the value (000 - 255), through the buttons UP/DOWN.
• Set the value of the [STRB], (0 - 20) through the buttons UP/DOWN.
3.14 EDITING CUSTOM PROGRAMS
To set the custom balance of red, blue and green:
• Press the button MENU, then press the button UP/DOWN so many times until the display shows [EDIT].
Press the button ENTER to confirm.
• Select the program PR.01 - PR.10.
• Each custom program has 30 steps that can be edited.
• Each step allows the creation of a scene using red (RED), green (GREEN), blue (BLUE), (STRB), (TIME) and (FADE).
• Set the value (000 - 255), through the buttons UP/DOWN.
3.15 SPECIAL FUNCTIONS
Press the button MENU and select through the directional buttons the [SETTINGS] mode; and press the button ENTER to confirm.
NOTE - The factory access password is UP + DOWN + UP + DOWN. Press ENTER to confirm the access.
It is possible to view to following functions:
UPLOAD
• Select [UPLd] to upload the custom programs from the current Master unit to the Slave units.
• In order to activate the upload function the password must be entered. Password is the same as the main access password.
REST
• In order to reset custom modesto default values select [REST].
COLOR
• [COLO] is for activate/deactivate the color calibration functions.
- When [RGBW] is selected, on RGB =255, 255, 255 the color is displayed as calibrated in CAL2
(RGBW).
- When [COLOR] is set [OFF], on RGB =255, 255, 255 the RGB values are not adjusted and the output is most powerful.
- When [UC] is selected, the RGB output adjusted to a standard preset universal color which balances fixtures from different generations.
DIMMER
• Enter [DIM] to select dimmer mode and dimmer speed. When dimmer is set to [OFF], the RGBW and
MASTER DIMMER are linear. The Dim1/2/3/4 are speed modes of the non linear dimmer, [DIM1] is the faster, while [DIM4] is the slowest.
NOTE - The factory default setting is [DIM4].
18
ARCLED7307HD
CURV
[CURV] allows the user to adjust the shape of the dimming curve. See the CURV chart to understand more about actual dimming curves.
CURV dimming
1: OFF
2: CV1
3: CV3
4: CV4
Fig.9
DERR
Enter to [DERR] to control in case of DMX signal errors.
- [SAVE] saves the latest data DMX on error DMX signal.
- [BLACK] allows you to activate the mode on error DMX blackout.
SLCK
[SLCK] is used to lock the settings menu. When [SLCK] is set to ON the user must insert passcode (UP +
DOWN + UP + DOWN) in order to access the settings menu.
STRB
This fixture allows for two different strobe personality settings, [CLAS] strobe or [SPEC] strobe. The [STRB] settings are only valid in the DMX personalities TOUR, AR2.S and TR16.
3.16 CALIBRATION FUNCTION
Press the button MENU to enter the password confirmation, to enter the correct password
UP+DOWN+UP+DOWN button, press the MENU in the correct password will enter show submenu.
WHITE SETTING
Enter the [CAL] mode to select white color of different color temperature;
• Press the button MENU then press the button UP/DOWN so many times until show [CAL1]. Press the button ENTER to confirm.
• There are 11 pre-programmed white colors (WHITE01 - WHITE11) can be edited by using red, green, and blue (Red - Green - Blue).
• Set the value (000 - 255), through the buttons UP and DOWN.
ARCLED7307HD
19
WHITE BALANCE
Enter the [CAL2] mode to adjust the RGB parameter to make different whites.
• Press the button MENU so many times until show [CAL2] and press the button ENTER to confirm.
• Select red, green or blue (RED - GREEN -BLUE), through the button UP/DOWN. Press the button
ENTER to confirm.
• Set the value 000 - 255, through the button UP/DOWN.
• When the new setting is activated, the DMX controller choose RGB=255, 255, 255 the write color will be made by actual RGB values on the [CAL2].
3.17 ACTIVATE THE PASSWORD
Enter the KEY mode to select whether the access password is on or off.
• Press the button MENU so many times until show [KEY] and press the button ENTER to confirm.
• Select [ON] or [OFF].
When the fixture is set as pass [ON], after 30 seconds or turn on the fixture next time, the fixture will need an access password to enter the display menu control.
NOTE - The factory access password is UP + DOWN + UP + DOWN. Press ENTER to confirm the access.
20
ARCLED7307HD
- 4 - MAINTENANCE
4.1 MAINTENANCE AND CLEANING THE UNIT
• Make sure the area below the installation place is free from unwanted persons during setup.
• Switch off the unit, unplug the main cable and wait until the unit has cooled down.
• All screws used for installing the device and any of its parts should be tightly fastened and should not be corroded.
• Housings, fixations and installation spots (ceiling, trusses, suspensions) should be totally free from any deformation.
• The main cables must be in impeccable condition and should be replaced immediately even when a small problem is detected.
• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.
Warning: we strongly recommend internal cleaning to be carried out by qualified personnel!
4.2 TROUBLESHOOTING
Problems
Fixture does not light up
General low light intensity
Fixture does not power up
Fixture does not respond to DMX
Possible causes
•
•
•
•
•
No mains supply
Dimmer fader set to 0
All color faders set to 0
Faulty LED
Faulty LED board
•
•
•
•
•
•
•
•
Dirty lens assembly
Misaligned lens assembly
No power
Loose or damaged power cord
Faulty internal power supply
Wrong DMX addressing
Damaged DMX cables
Bouncing signals
Checks and remedies
•
•
•
•
•
Check the power supply voltage
Increase the value of the dimmer channels
Increase the value of the color channels
Replace the LED board
Replace the LED board
•
•
•
•
•
•
•
•
Clean the fixture regularly
Install lens assembly properly
Check for power on power outlet
Check power cord
Replace internal power supply
Check control panel and unit addressing
Check DMX cables
Install terminator as suggested
Contact an authorized service center in case of technical problems or not reported in the table can not be resolved by the procedure given in the table.
ARCLED7307HD
- 5 - APPENDIX
5.1 EXPLODED VIEW
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
17
Fig.10
18
19
20
21
22
No ITEM
1 Rubber B
2 Glass
3 3 in 1 lens frame front cover
4
LED3 in 1 lens
5
6
3 in 1 lens frame back cover
LED board
7
8
9
10
11
Thermal switch
Thermal switch holder
Power supply
Adaptor PCB
Driver board
No ITEM
12 Display board
13
Button pressed plate
14
15
16
17
Display screen lens
Display board rubber
Rubber C
XLR 3 cores socket (male)
18
19
20
21
22
XLR 3 cores socket (female)
PS socket (male)
PS socket (male)
Rubber A
Adjusting stainless steel knob
21
"
Place Stamp Here
Affrancare
Spett.le
Music&Lights S.r.l.
Via Appia Km 136.200
04020 Itri (LT) Italy
"
Music & Lights S.r.l.
entertainment technologies
Via Appia km 136,200 - 04020 Itri (LT) ITALY tel. +39 0771 72190 fax +39 0771 721955 www.musiclights.it
ISO 9001:2008
Certified Company
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project