Alcatel-Lucent Service Aggregation Router 7705 Installation Manual

Alcatel-Lucent 7705

SERVICE AGGREGATION ROUTER | RELEASE 1.0

S A R - 8 C H A S S I S I N S T A L L A T I O N G U I D E

Alcatel-Lucent Proprietary

This document contains proprietary information of Alcatel-Lucent and is not to be disclosed or used except in accordance with applicable agreements.

Copyright 2008 © Alcatel-Lucent. All rights reserved.

Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is subject to change without notice.

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners.

Copyright 2008 Alcatel-Lucent.

All rights reserved.

Disclaimers

Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life-support machines, or weapons systems, in which the failure of products could lead directly to death, personal injury, or severe physical or environmental damage. The customer hereby agrees that the use, sale, license or other distribution of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the use, sale, license or other distribution of the products in such applications.

This document may contain information regarding the use and installation of non-Alcatel-Lucent products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent tries to ensure that this information accurately reflects information provided by the supplier, please refer to the materials provided with any non-Alcatel-Lucent product and contact the supplier for confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete information provided about non-Alcatel-Lucent products.

However, this does not constitute a representation or warranty. The warranties provided for

Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by

Alcatel-Lucent and its customers.

This document was originally written in English. If there is any conflict or inconsistency between the

English version and any other version of a document, the English version shall prevail.

When printed by Alcatel-Lucent, this document is printed on recycled paper.

Table of Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Mandatory Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

List of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

General Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Canada Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

United States Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

European Union Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

EU Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Australia/New Zealand Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

China Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7705 SAR-8 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7705 SAR-8 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Slot Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Distribution Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SAR System Installation Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Chassis Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Adapter Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

CSM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Fan Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Component Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Component Operating Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Installation Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Chassis Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

7705 SAR-8 Installation Guide Page 3

Table of Contents

Installing the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Unpacking the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Unpacking Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Installing the Chassis in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Rack-Mounting the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Chassis Ground Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Making the Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

DC Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Wiring and Connecting DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

DC-Input Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Wiring the DC Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Installing the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Installing Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Installing a Distribution Panel in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Rack-Mounting a BNC or RJ45 Distribution Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Managing Cable Connections to Adapter Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Ethernet and Copper Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Fiber Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Making a Shield Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Making External Synchronization Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Connecting an External Synchronization Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Providing an External Synchronization Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Initializing and Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Powering Up the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Power-Up and Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Troubleshooting Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Establishing Router Management Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Console Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Telnet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Running Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Provisioning CSM and Adapter Card Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Card and Card-Type Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

MDA and MDA-Type Commands for Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Page 4 7705 SAR-8 Installation Guide

Table of Contents

Appendix A: Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

CSM Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Fan Module Connectors and LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Adapter Card Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Appendix B: Field-Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Replacing a CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Removing a CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Replacing a CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Replacing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Changing the Adapter Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Removing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Replacing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Replacing the Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Removing the Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Replacing the Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Installing a Slot Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Appendix C: Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

CSM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Management Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Management Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Console Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Fan Module Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

External Alarms Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

External Alarms Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Alarm examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Adapter Card Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Standards and Protocol Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

7705 SAR-8 Installation Guide Page 5

Table of Contents

Page 6 7705 SAR-8 Installation Guide

List of Tables

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 1: Information Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Mandatory Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 2: List of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

7705 SAR-8 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 3:

Table 4:

Distribution Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

T1/E1 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Table 5:

Table 6:

Table 7:

7705 SAR-8 Chassis Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Adapter Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Table 8:

Table 9:

CSM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Fan Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 10: Component Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 11: 7705 SAR-8 Hardware Components for DC Operational Requirements . . . . . . . . . . . . . . . . . . . . . 57

Table 12: Chassis Clearance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 13: Storage Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Installing the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Table 14: Unpacking the 7705 SAR-8 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Table 15: Rack-Mounting the 7705 SAR-8 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Table 16: Ground Wire Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Table 17: Chassis Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

DC Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Table 18: DC Power Connection Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Installing the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Table 19: CSM Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Table 20: Fan Module Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Table 21: Adapter Card Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Table 22: SFP Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Table 23: Rack-Mounting the Distribution Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Table 24: Redundant External Synchronization Input Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

7705 SAR-8 Installation Guide Page 7

List of Tables

Initializing and Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Table 25: Console Port Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Appendix A: Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Table 26: 7705 SAR-8 CSM Connector and LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Table 27: 7705 SAR-8 Fan Module Connector and LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Appendix B: Field-Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Table 28: Adapter Card Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Appendix C: Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Table 29: Ethernet Management Port Pinouts—RJ45 Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Table 30: Console Port Pinouts—DB9 Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Table 31: External Alarms Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Table 32: Alarm Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Page 8 7705 SAR-8 Installation Guide

List of Figures

Mandatory Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 1:

Figure 2:

Figure 3:

Protective Earth (ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Earth (ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

WEEE Symbol for post-August 13, 2005 Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7705 SAR-8 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 4:

Figure 5:

Figure 6:

Figure 7:

7705 SAR-8 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7705 SAR-8 Slot Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

7705 SAR-8 CSM Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

7705 SAR-8 Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 8:

Figure 9:

7705 SAR-8 Slot Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 10: BNC Distribution Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 11: RJ45 Distribution Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 12: Chassis Clearance Requirements (View from Top) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Installing the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Figure 13: Unpacking the 7705 SAR-8 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Figure 14: Installing the 7705 SAR-8 Chassis in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Figure 15: Preparing the Ground Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Figure 16: Attaching the Chassis Ground Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

DC Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Figure 17: DC Power Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Installing the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Figure 18: Installing the CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Figure 19: Installing the Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Figure 20: Installing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Figure 21: Installing an SFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Figure 22: Installing a Distribution Panel in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Figure 23: Managing Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Figure 24: Installing Redundant External Synchronization Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

7705 SAR-8 Installation Guide Page 9

List of Figures

Initializing and Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Figure 25: Files on the Compact Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Figure 26: Console Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Figure 27: Management Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Appendix A: Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Figure 28:

CSM Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Figure 29:

Fan Module Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Appendix B: Field-Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Figure 30: Replacing a CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Figure 31: Removing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Figure 32: Replacing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Figure 33: Removing the Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Figure 34: Replacing the Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Appendix C: Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Figure 35: CSM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Figure 36: Fan Module Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Page 10 7705 SAR-8 Installation Guide

List of Acronyms

Acronym

2G

3G

ABR

AC

ACL

AIS

Apipe

ARP

AS

ASAP

ATM

ATM PVC

B-bit

Batt A

BFD

BOF

BSTA

BTS

CBN

CBS

CC

CE

7705 SAR-8 Installation Guide

Expansion second generation wireless telephone technology third generation mobile telephone technology available bit rate alternating current attachment circuit access control list alarm indication signal

ATM VLL address resolution protocol autonomous system any service, any port asynchronous transfer mode

ATM permanent virtual circuit beginning bit (first packet of a fragment) battery A bidirectional forwarding detection boot options file

Broadband Service Termination Architecture base transceiver station common bonding networks committed buffer space control channel customer edge circuit emulation

Page 11

List of Acronyms

Acronym

CPE

Cpipe

CPU

CRC

CRON

CSM

CSPF

CV

CIR

CLI

CLP

CoS

CEM

CES

CESoPSN

CIDR

CW

DC

DC-C

DC-I

DDoS

DHCP

DNS

DoS dot1q

Page 12

Expansion circuit emulation circuit emulation services circuit emulation services over packet switched network classless inter-domain routing committed information rate command line interface cell loss priority class of service customer premises equipment circuit emulation (or TDM) VLL central processing unit cyclic redundancy check a time-based scheduling service (from chronos = time)

Control and Switching Module constrained shortest path first connection verification customer VLAN (tag) control word direct current

DC return - common

DC return - isolated distributed DoS dynamic host configuration protocol domain name server denial of service

IEEE 802.1q encapsulation for Ethernet interfaces

7705 SAR-8 Installation Guide

List of Acronyms

Acronym

FDB

FEC

FIB

FTN

Epipe

ESD

FC

FCS

DSCP

DTE

DU e911

E-bit

ECMP

EFM

ELER

GigE

GRE

GSM

HSDPA

HSPA

IBN

ICMP

ICP

IEEE

IETF

7705 SAR-8 Installation Guide

Expansion differentiated services code point data termination equipment downstream unsolicited enhanced 911 service ending bit (last packet of a fragment) equal cost multi-path

Ethernet in the first mile egress label edge router

Ethernet VLL electrostatic discharge forwarding class frame check sequence forwarding database forwarding equivalence class forwarding information base

FEC-to-NHLFE

Gigabit Ethernet generic router encapsulation

Global System for Mobile Communications (2G) high-speed downlink packet access high-speed packet access isolated bonding networks

Internet control message protocol

IMA control protocol cells

Institute of Electrical and Electronics Engineers

Internet Engineering Task Force

Page 13

List of Acronyms

Acronym

LLID

LSP

LSR

LTN

MAC

MBB

MBS

IP

LCP

LDP

LER

ILER

ILM

IMA

IOM

MD5

MDA

MEF

MFC

MIB

MIR

MLPPP

MP

MPLS

Page 14

Expansion ingress label edge router incoming label map inverse multiplexing over ATM input/output module

Internet Protocol link control protocol label distribution protocol label edge router loopback location ID label switched path label switch router

LSP ID to NHLFE media access control make-before-break maximum buffer space maximum burst size media buffer space message digest version 5 algorithm media dependent adapter

Metro Ethernet Forum multi-field classification management information base minimum information rate multilink point-to-point protocol multilink protocol multiprotocol label switching

7705 SAR-8 Installation Guide

List of Acronyms

Acronym

MRRU

MRU

MTSO

MTU

NHLFE

NNI

Node-B

PID

PIR

POP

PPP

PSN

PVCC

PW

PWE3

QoS

RDI

OAM

OAMPDU

OS

OSS

PDU

PE

PHY

7705 SAR-8 Installation Guide

Expansion maximum received reconstructed unit maximum receive unit mobile trunk switching office maximum transmission unit multi-tenant unit next hop label forwarding entry network-to-network interface similar to BTS but used in 3G networks (term used in

UMTS (3G systems while BTS is used in GSM (2G systems) operations, administration, and maintenance

OAM protocol data units operating system operations support system protocol data units provider edge router physical layer protocol ID peak information rate point of presence point-to-point protocol packet switched network permanent virtual channel connection pseudowire pseudowire emulation edge-to-edge quality of service remote defect indication

Page 15

List of Acronyms

Acronym

SAP

SAR

SAR-8

SDP

SIR

SLA

SNTP

SPF

RED

RSVP

RSVP-TE

R&TTE

RT

RTM

RTN

RTP

SSH

TCP

TDM

TLDP

TLV

TOS

TPID

TTM

UDP

UMTS

Page 16

Expansion random early discard resource reservation protocol resource reservation protocol - traffic engineering

Radio and Telecommunications Terminal Equipment receive/transmit route table manager battery return real-time protocol service access point service aggregation router service aggregation router - 8-slot chassis service destination point sustained information rate

Service Level Agreement simple network time protocol shortest path first secure shell transmission control protocol time division multiplexing targeted LDP type length value type of service tag protocol identifier tunnel table manager user datagram protocol

Universal Mobile Telecommunications System (3G)

7705 SAR-8 Installation Guide

Acronym

UNI

VC

VCCV

VCI

VLAN

VLL

VoIP

VP

VPC

VPI

VPN

WCDMA

WRED

List of Acronyms

Expansion user-to-network interface virtual circuit virtual circuit connectivity verification virtual circuit identifier virtual LAN virtual leased line voice over IP virtual path virtual path connection virtual path identifier virtual private network wideband code division multiple access (transmission protocol used in UMTS networks) weighted random early discard

7705 SAR-8 Installation Guide Page 17

List of Acronyms

Page 18 7705 SAR-8 Installation Guide

Preface

About This Guide

This guide provides site preparation recommendations, step-by-step procedures to install the

Alcatel-Lucent 7705 Service Aggregation Router (SAR) in a standard 19-inch utility rack, and instructions to install, provision, and remove the Control and Switching Module (CSM), adapter cards, and Fan module.

After the hardware installation process is completed, refer to the 7705 SAR OS documentation set for details on the boot process, software configuration, and Command

Line Interface (CLI) information to configure system and network parameters.

List of Technical Publications

The 7705 SAR-series OS documentation set is composed of the following guides:

• 7705 SAR OS Basic System Configuration Guide

This guide describes basic system configurations and operations.

• 7705 SAR OS System Management Guide

This guide describes system security and access configurations as well as event logging and accounting logs.

• 7705 SAR OS Interface Configuration Guide

This guide describes card and port provisioning.

• 7705 SAR OS Router Configuration Guide

This guide describes logical IP routing interfaces, IP-based filtering, and routing policies.

• 7705 SAR OS MPLS Guide

This guide describes how to configure Multiprotocol Label Switching (MPLS) and

Label Distribution Protocol (LDP).

• 7705 SAR OS Services Guide

This guide describes how to configure service parameters such as service access points (SAPs), service destination points (SDPs), customer information, user services, and Operations, Administration and Management (OAM) tools.

7705 SAR-8 Installation Guide Page 19

Preface

• 7705 SAR OS Quality of Service Guide

This guide describes how to configure Quality of Service (QoS) policy management.

Warnings and Notes

Observe the warnings and notes in this guide to avoid injury or router damage during installation and maintenance. Follow the safety procedures and guidelines when working with and near electrical equipment. Warning statements and notes are provided in each chapter.

Audience

This guide is intended for network installers and system administrators who are responsible for installing, configuring, or maintaining networks. This guide assumes you are familiar with electronic and networking technologies.

Information Symbols

Table 1

describes symbols contained in this guide.

Symbol Meaning

Danger

Warning

Table 1: Information Symbols

Description

This symbol warns that improper handling and installation could result in bodily injury. An electric shock hazard could exist. Before you begin work on this equipment, be aware of hazards involving electrical circuitry, be familiar with networking environments, and instigate accident prevention procedures.

This symbol warns that improper handling and installation could result in equipment damage or loss of data.

Caution This symbol warns that improper handling may reduce your component or system performance.

Page 20 7705 SAR-8 Installation Guide

Preface

Symbol Meaning

Note

Class 1 Laser Product

Table 1: Information Symbols (Continued)

Description

This symbol provides additional operational information.

Class 1 laser products are identified in the adapter card installation guides. Only approved Class 1 replaceable laser transceivers should be used with this product.

Technical Support

If you purchased a service agreement for your 7705 SAR-8 and related products from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance. If you purchased an Alcatel-Lucent service agreement, contact technical assistance at:

Web: http://www1.alcatel-lucent.com/comps/pages/carrier_support.jhtml

7705 SAR-8 Installation Guide Page 21

Preface

Page 22 7705 SAR-8 Installation Guide

Mandatory Regulations

In This Chapter

The following sections describe the mandatory regulations that govern the installation and operation of the 7705 SAR-8:

•

List of Terms on page 24

•

General Requirements on page 25

•

Canada Regulations on page 28

•

United States Regulations on page 29

•

European Union Regulations on page 31

•

Australia/New Zealand Regulations on page 35

•

China Regulations on page 36

7705 SAR-8 Installation Guide Page 23

Mandatory Regulations

List of Terms

Table 2

lists the terms used in this chapter.

EEC

EMC

EMI

EN

FCC

ICES

IEC

IEE

Term

ACMA

ACTA

ANSI

AS/NZ

CE

CFR

CSA International

ETSI

LVD

NRTL

OSHA (USA)

RoHS

SELV

UL

WEEE

Table 2: List of Terms

Expansion

Australian Communications and Media Authority

Administrative Council for Terminal Attachments

American National Standards Institute

Australian/New Zealand standard

Conformité Européene

Code of Federal Regulations

Canadian Standards Association International

European Economic Community

Electromagnetic Compatibility

Electromagnetic Interference

European Standards

Federal Communications Commission

Interference Causing Equipment Standard

International Electrotechnical Commission

Institute of Electrical Engineers (UK)

European Telecommunications Standards Institute

Low Voltage Directive

Nationally Recognized Testing Laboratory

Occupational Safety and Health Administration (USA)

Restriction of the use of certain Hazardous Substances

Safety Extra Low Voltage

Underwriters Laboratories

Waste Electrical and Electronic Equipment

Page 24 7705 SAR-8 Installation Guide

Mandatory Regulations

General Requirements

The sections that follow outline the mandatory regulations that govern the installation and operation of the

7705 SAR-8

. You must adhere to these instructions so that your system meets regulatory requirements.

Danger: When removing cards from a shelf under power, some of the components such as the DC converters may be extremely hot. Handle by the card guides only.

Warning: There are no user-serviceable parts in this unit. Refer servicing to qualified personnel.

Warning: To prevent accidental electrical short circuits, align the card correctly between the card guides before inserting it in the slot.

Warning: The unit should be connected to a DC branch circuit with a maximum 10A circuit breaker or fuse that meets the requirements for branch circuit protection. A suitable disconnect device, such as a circuit breaker or switch, must be provided in the DC branch circuit and must be used to disconnect power to the system during servicing.

Equipment Interconnection Points

Interconnection points of the

7705 SAR-8

are defined as the following SELV connectors:

• T1/E1

• Ethernet (10/100/1000 Base-T)

• alarms

• clock inputs and clock outputs (BITS, 2 MHz, 5 MHz, 10 MHz)

SELV

Connect SELV circuits on this equipment only to other circuits that comply with the requirements of SELV circuits as defined in CSA C22.2 No. 60950-1, UL 60950-1,

EN 60950-1, AS/NZS 60950-1, and IEC60950-1.

Prevention of Access

The 7705 SAR-8 must be accessible only to authorized personnel. Install this apparatus in a restricted access location or similar environment to prevent unauthorized access.

7705 SAR-8 Installation Guide Page 25

Mandatory Regulations

Laser Interface

The

7705 SAR-8

uses a fiber-optic communications method and is an FDA and IEC Class 1

Laser product. Only trained service personnel thoroughly familiar with laser radiation hazards should install or remove the fiber-optic cables and cards in this system.

Protective Safety Ground (Earth)

The cable used for safety ground should be at least the same gauge as the supply conductors, green and yellow in color, and of sufficient length to connect the building earth point to the chassis ground connection (refer to the installation chapter for specific instructions on connecting the chassis ground).

EMC Compliance

EMC compliance may require the use of ferrites, shielded cables or other special accessories. Where required, these special accessories must be installed as per the instructions.

To maintain EMC compliance, cables that are shielded and grounded at both ends must be used on the following cards, interfaces, and ports:

• CSM card

→ Management (Ethernet), DB9 Console, and Synchronization interfaces

• 8-port Ethernet Adapter card

→ Fast Ethernet interface (CAT5 shielded cable)

→ Gigabit Ethernet interface (CAT5E shielded cable)

• 16-port T1/E1 ASAP Adapter card

→ T1 and E1 interfaces

• Fan module

→ DB15 Alarm port

Page 26 7705 SAR-8 Installation Guide

Mandatory Regulations

Regulatory Symbols

The

7705 SAR-8

uses various regulatory approvals symbols. They may be used on product markings such as approvals labels. These symbols are described in IEC 417.

Figure 1 and Figure 2

show symbols of a terminal that you must connect to earth ground before you make any other connections to the equipment.

Figure 1: Protective Earth (ground)

9717

Figure 2: Earth (ground)

9718

7705 SAR-8 Installation Guide Page 27

Mandatory Regulations

Canada Regulations

This section describes the mandatory regulations that govern the installation and operation of the

7705 SAR-8

in Canada.

Industry Canada Regulations

ICES-003: Interference-Causing Equipment Standard Digital Apparatus

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

IC CS-03: Specification for Terminal Equipment, Terminal Systems,

Network Protection Devices, Connection Arrangements and Hearing Aids

Compatibility

This product meets the applicable Industry Canada technical specifications with respect to

IC CS-03: Specification for Terminal Equipment, Terminal Systems, Network Protection

Devices, Connection Arrangements and Hearing Aids Compatibility

Registration number: IC: 1737F-0010.

EMC Compliance

EMC compliance may require the use of ferrites, shielded cables or other special accessories. Where required, these special accessories must be installed as per the instructions.

Safety Approval for DC Systems

The DC source for the system must meet the requirements of a SELV source to comply with

CSA standard C22.2 No. 60950-1. Use the system with a SELV secondary source that is electrically isolated from the AC source and that is grounded reliably.

The 7705 SAR-8 is safety certified according to CSA standard C22.2 No. 60950-1 by CSA.

Page 28 7705 SAR-8 Installation Guide

Mandatory Regulations

United States Regulations

This section describes the mandatory regulations that govern the installation and operation of the

7705 SAR-8

in the United States.

Federal Communications Commission

FCC Part 15

Important! Changes or modifications not expressly approved by Alcatel-Lucent could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s expense.

FCC Part 68

The T1 network interface on this equipment meets the FCC specifications.

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the

ACTA. On the equipment is a label that contains, among other information, a product identifier in the format of AAAEQ##TXXXX.

Identification Number: GQ6DENAN7705SAR

In the event that repairs to this equipment are needed, contact:

Technical Support Services

Alcatel-Lucent

Within the United States: 1-866-582-3688, prompt 1

7705 SAR-8 Installation Guide Page 29

Mandatory Regulations

NRTL

This equipment is certified by the NRTL as meeting the requirements of UL 60950-1, Safety of Information Technology Equipment.

NRTL Approval for External DC Supplies

When the system is equipped with an AC rectifier, the rectifier must have NRTL-accredited approval. In addition, the DC outputs must meet UL 60950-1 SELV requirements.

Safety Approval for DC Systems

The DC source for the system must meet the requirements of a SELV source in accordance with UL 60950-1. You must use the system with a SELV secondary source that is electrically isolated from the AC source and that is grounded reliably.

Food and Drug Administration

This product complies with 21 CFR 1040.10 and 1040.11 regulations, which govern the safe use of lasers. Only qualified service personnel, thoroughly familiar with laser radiation hazards, should install or remove the fiber-optic cables used in this system. You can find information about the safe use of lasers in ANSI Z 136.1: Safe Use of Lasers and ANSI Z

136.2: Safe Use of Lasers in Optical Fiber Communications Systems. You can obtain these documents and other instructional material from:

Laser Institute of America

12424 Research Parkway, Suite 125

Orlando, FL 32826-3274

Page 30 7705 SAR-8 Installation Guide

Mandatory Regulations

European Union Regulations

Declaration of Conformity

Hereby, Alcatel-Lucent declares that the equipment documented in this publication is in compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC and

2004/108/EC

.

The technical documentation as required by the Conformity Assessment procedure is kept at the Alcatel-Lucent location that is responsible for this product. For more information please contact your local Alcatel-Lucent Customer Service Organization.

EU Compliance Statement

This product has been CE marked in accordance with the requirements of European

Directive 99/05/EC, the Radio and Telecommunications Terminal Equipment Directive

(R&TTE),

and 2004/108/EC, the Electromagnetic Compatibility (EMC) Directive

.

EMC/EMI Compliance

The equipment complies with the following EMC and EMI specification: EN 300 386

Class A.

General

This equipment must be permanently grounded.

Laser Interface

The system uses laser devices that are rated in accordance with IEC 60825-1 as Class 1 devices.

7705 SAR-8 Installation Guide Page 31

Mandatory Regulations

Safety Approval for DC Systems

The DC source for the system must meet the requirements of a SELV source as defined in

EN 60950-1. For 60V station battery systems, the source is considered TNV-2 as per

IEC/EN 60950-1 and must have reinforced insulation from the AC mains.

The equipment complies with the following Product Safety specification: EN 60950-1.

Protective Earth

Protective earth is referred to as chassis ground in this document. A green and yellow colored earth wire must be connected from the site equivalent of the AC earth to all shelves in accordance with IEE Wiring Regulations (16th edition). This connection is made via the chassis ground connection (refer to the installation chapter for specific instructions on connecting the protective earth). The protective earth is also carried by the mains plug and socket (for AC systems only).

Approval for External AC Rectifiers

When the system is equipped with an external AC rectifier, the rectifier must meet

EN 60950-1 SELV DC output requirements. Make sure that the rectifier is rated and adjusted for the appropriate AC input voltage and frequency for the country where it is installed. Set the output of the rectifier according to the installation and operating instructions of the manufacturer, to provide output levels that coincide with the nominal DC input ratings of the system.

Eco-Environmental

Packaging collection and recovery requirements

Countries, states, localities, or other jurisdictions may require that systems be established for the return and/or collection of packaging waste from the consumer, or other end user, or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the return and/or collection of the packaging waste may be established.

For more information regarding collection and recovery of packaging and packaging waste within specific jurisdictions, please contact the Environmental Health and Safety organization.

Page 32 7705 SAR-8 Installation Guide

Mandatory Regulations

For installations not performed by Alcatel-Lucent, please contact the Alcatel-Lucent

Customer Support Center at:

Technical Support Services

+1 630 224 4672, prompt 2

Recycling / take-back / disposal of product

Electronic products bearing or referencing the symbol shown in

Figure 3

, when put on the market within the European Union, shall be collected and treated at the end of their useful life in compliance with applicable European Union and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal.

Note: In the European Union, the WEEE symbol (a wheeled trash bin that has been crossed out and is positioned above a solid bar) indicates that the product was put on the market after 13 August 2005. This product is compliant with the WEEE marking requirements of

DIRECTIVE 2002/96/EC Waste Electrical and Electronic Equipment (WEEE).

Figure 3: WEEE Symbol for post-August 13, 2005 Product

Moreover, in compliance with legal requirements and contractual agreements, where applicable, Alcatel-Lucent will offer to provide for the collection and treatment of Alcatel-

Lucent products bearing the logo at the end of their useful life, or products displaced by

Alcatel-Lucent equipment offers. For information regarding take-back of equipment by

Alcatel-Lucent, or for more information regarding the requirements for recycling/disposal of product, please contact your Alcatel-Lucent Account Manager or Alcatel-Lucent Takeback

Support at [email protected].

7705 SAR-8 Installation Guide Page 33

Mandatory Regulations

Material Content Compliance

European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous

Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment.

Alcatel-Lucent products shipped to the EU after 1 July 2006 comply with the EU RoHS

Directive.

Page 34 7705 SAR-8 Installation Guide

Mandatory Regulations

Australia/New Zealand Regulations

This section describes the mandatory regulations that govern the installation and operation of the 7705 SAR-8 in Australia and New Zealand.

ACMA Regulations

The 7705 SAR-8 complies with the ACMA requirements and the product is marked with the

'A Tick' under the Supplier Code N594.

EMC

This Class A digital apparatus complies with AS/NZS CISPR22.

Telecom

This product meets the applicable ACMA technical specifications: AS/ACIF S016.

Safety

All products supplied in Australia are to be safe and to comply with an applicable Australian

Standard electrical safety standard.

The 7705 SAR-8 complies with the AS/NZS 60950 — Business Equipment, Computers,

Telecommunications requirements.

7705 SAR-8 Installation Guide Page 35

Mandatory Regulations

China Regulations

The statements that follow are the product conformance statements that apply to the

7705 SAR-8 when deployed in China.

Safety

The equipment complies with the Product Safety specification of IEC 60950-1.Eco-

Environmental.

Packaging Collection and Recovery Requirements

Countries, states, localities, or other jurisdictions may require that systems be established for the return and/or collection of packaging waste from the consumer, or other end user, or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the return and/or collection of the packaging waste may be established.

For more information regarding collection and recovery of packaging and packaging waste within specific jurisdictions, please contact the Alcatel-Lucent Environmental Health and

Safety organization. For installations not performed by Alcatel-Lucent, please contact the

Alcatel-Lucent Customer Support Center at:

Technical Support Services

+1 630 224 4672, prompt 2

Material Content Compliance

The People’s Republic of China Ministry of Information Industry has published a regulation

(Order #39) and associated standards regarding restrictions on hazardous substances (China

RoHS). Currently, the legislation requires all Electronic and Information Products (EIP) to comply with certain labeling and documentation requirements. Alcatel-Lucent products manufactured on or after 1 March 2007, that are intended for sale to customers in the China market, comply with these requirements.

Page 36 7705 SAR-8 Installation Guide

Mandatory Regulations

In accordance with the People’s Republic of China Electronic Industry Standard “Marking for the Control of Pollution Caused by Electronic Information Product” (SJ/T11364-2006), customers may access Alcatel-Lucent’s Hazardous Substances Table information at either of the following two URLs:

• Access via the Alcatel-Lucent Corporate website at: http://www.alcatel-lucent.com/cn

• Access via the Alcatel Shanghai Bell website at: http://www.alcatel-sbell.com.cn/product_solution/in4.asp

7705 SAR-8 Installation Guide Page 37

Mandatory Regulations

Page 38 7705 SAR-8 Installation Guide

7705 SAR-8 Overview

In This Chapter

This chapter provides an introduction to the Alcatel-Lucent 7705 SAR-8:

•

7705 SAR-8 Components on page 40

→

Chassis on page 40

→

CSM on page 41

→

Adapter Cards on page 42

→

Slot Covers on page 43

→

Power System on page 43

→

Fan Module on page 44

→

Distribution Panels on page 46

•

SAR System Installation Process on page 49

7705 SAR-8 Installation Guide Page 39

7705 SAR-8 Components

7705 SAR-8 Components

The main components of the 7705 Service Aggregation Router (SAR) are the chassis,

Control and Switching Module (CSM), adapter cards, and Fan module. In addition, there are optional distribution panels to connect the adapter cards to the customer equipment.

Figure 4 shows the front view of the 7705 SAR-8. There are eight horizontal slots for the

CSMs and adapter cards, and one vertical slot for the Fan module. The connectors for the

DC power feeds are located to the right of the Fan module and are factory-installed. The

CSM, adapter cards, and Fan module are installed by the customer. All physical connections are made from the front of the unit, including the chassis ground point. There are no back panel connections.

Figure 4: 7705 SAR-8 Front View

SLOT ID

CSM A

MDA 1

MDA 3

CSM B

MDA 2

MDA 5

MDA 4

MDA 6

CSM

Stat

Act

Pwr

Mgmnt Port

A16-CHDS1

Stat Act

Pwr Port

Console

Ports 1-16

Sync

In Out

A8-ETN

Stat

Pwr

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link

Act Link

Act

7

CSM

Stat Act

Pwr

Mgmnt Port

A16-CHDS1

Stat

Act

Pwr Port

A16-CHDS1

Stat Act

A8-ETN

Pwr

Port

Stat

Console

Ports 1-16

Ports 1-16

Pwr

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link

Act

Link Act

7

Sync

In

Out

8

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19634

Chassis

The chassis is shipped with a backplane, card cage, and connectors for the DC power feeds.

Mounting brackets for the 7705 SAR-8 chassis are factory-installed so the unit can be mounted in a recommended 19-inch wide rack. The chassis grounding stud is on the righthand side bracket. Slot covers are also factory-installed.

Figure 5 identifies the slots used for the CSMs, adapter cards (MDA), and Fan module. In

redundant systems, the CSMs go in slots CSM A and CSM B, and the adapter cards are installed in slots MDA 1 through MDA 6. In simplex systems, the CSM goes in slot CSM A, a slot cover goes on slot CSM B, and the adapter cards go in slots MDA 1 through MDA 6.

Page 40 7705 SAR-8 Installation Guide

7705 SAR-8 Overview

.

Figure 5: 7705 SAR-8 Slot Identification

CSM A

MDA 1

MDA 3

MDA 5

CSM B

MDA 2

MDA 4

MDA 6

Batt A

FAN

Batt B

19635

CSM

The Control and Switching Module (CSM) has three main functions:

• it provides the management and console interfaces to the 7705 SAR-8

• it provides system synchronization interfaces for external synchronization input and output signals

• it controls the routing, switching, and services functions for the entire system

Each CSM is shipped with one compact flash memory device that stores system boot images, software images, and configuration files and logs. The compact flash device cannot be accessed or removed by an operator or installer.

Figure 6 shows the CSM faceplate. Refer to

CSM Connectors and LEDs on page 112

for identification and description of the CSM faceplate features.

Figure 6: 7705 SAR-8 CSM Features

CSM

Stat Act

Pwr

Mgmt Port Console

Sync

In Out

19636

There must be at least one CSM installed in the 7705 SAR-8. Install two CSMs for system redundancy. The redundant CSM operates in standby mode and takes over system operation if the active (primary) CSM fails. CSMs are field-replaceable and hot-swappable. Refer to

7705 SAR OS Basic System Configuration Guide for information on CSM redundancy.

7705 SAR-8 Installation Guide Page 41

7705 SAR-8 Components

The CSM connects directly to the backplane and carries traffic between adapter cards. The switch fabric portion of the CSM receives and directs traffic to the appropriate destinations according to the routing information.

The CSM also provides 1.0/2.3 coaxial connectors for an external synchronization input and output. For redundant CSM configurations, a Y-cable can be used to connect the Sync In connectors on the two CSMs to the same external synchronization source.

Note: There is an IOM software module on the CSM that must be activated before any adapter card and port parameter can be provisioned and configured. The IOM is activated using the card

and card-type

CLI commands to specify its slot number and card type.

See Provisioning CSM and Adapter Card Parameters on page 108 for more information.

Adapter Cards

Figure 7 shows a sample adapter card. Adapter cards on the 7705 SAR-8 provide a wide

variety of interfaces of different speed and type, including Ethernet (10/100/1000 Base-T and optical), T1/E1 with ATM and IMA, and TDM (channelized and unchannelized).

The following adapter cards are supported in the 7705 SAR-8:

• 16-port T1/E1 ASAP Adapter card

• 8-port Ethernet Adapter card

The 16-port T1/E1 ASAP Adapter cards can support T1/E1 connections via a distribution panel. The 8-port Ethernet Adapter adapter cards can support six 10/100 Base-T ports and 2

SFP ports.

Adapter cards are hot-swappable and field-replaceable by qualified personnel. Adapter cards

install in slots MDA 1 through MDA 6. Refer to Figure 5 for adapter card slot locations on

the 7705 SAR-8, and to the appropriate adapter card installation guide for installation and

LED information.

Page 42 7705 SAR-8 Installation Guide

7705 SAR-8 Overview

Figure 7: 7705 SAR-8 Adapter Card

A16-CHDS1

Stat

Act

Pwr

Port

Ports 1-16

19637

Slot Covers

Figure 8 shows a slot cover. Slot covers (blank panels) are required on all empty slots to

prevent dust accumulation, help control airflow and confine electromagnetic interference, and for safety reasons. Slot covers do not have board components or connector pins.

Figure 4

shows a cover on slot MDA 3.

Figure 8: 7705 SAR-8 Slot Cover

19638

Power System

The 7705 SAR-8 has two power connectors mounted on the front of the chassis. These connectors provide access for two independent -48/-60 VDC power feeds, providing power redundancy for the system. When only one power feed is used, the system does not have power supply redundancy. The 7705 SAR-8 has a distributed power design, where each

CSM and adapter card provides independent power for its own functionality. The power system has no field-replaceable parts.

The DC power LEDs are located on the Fan module (see

Figure 9

). Refer to

Fan Module

Connectors and LEDs on page 114 for a description of the Fan module LEDs.

7705 SAR-8 Installation Guide Page 43

7705 SAR-8 Components

Refer to DC Power Connections on page 77

for requirements and information regarding preparing DC power cables.

Note: For sites that operate using +24VDC supplies, a +24VDC to -48VDC converter is needed to provide power to the 7705 SAR-8.

Figure 9: Fan Module

7705 SAR-8

FAN

Batt A

Batt B

Alarms

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19639

Fan Module

Figure 9 shows the Fan module. The Fan module provides cooling for the system, as well as

alarm indicators (LEDs), an external alarm I/O connector, and an Audible Alarm

Cutoff/Lamp Test (ACO/LT) pushbutton.

The Fan module is hot-swappable and field-replaceable by qualified personnel. It must always be installed and fully operational while the 7705 SAR-8 is powered up. During routine maintenance and Fan module replacement, the system can operate safely for up to four minutes.

Fan Operation

The Fan module houses eight fans. Air enters from the intake vent on the right side of the chassis and exits through the exhaust vent on the left side. The fans have one operating speed

(full speed) and are always operational, regardless of ambient temperature.

Page 44 7705 SAR-8 Installation Guide

7705 SAR-8 Overview

Individual fans are not field-replaceable; however, there is sufficient cooling even if one of the fans fails. A critical alarm is generated when one or more fans fails. If one fan has failed the module should be replaced as soon as possible. If more than one fan has failed, the Fan module must be replaced immediately.

The FAN LED on the Fan module provides the following indications:

• green: normal operation

• amber: one or more fans out of operation

• unlit: fan power failure

Monitoring Temperature

Each CSM and adapter card has temperature sensors to continuously monitor its own temperature and report the temperature to the CSM. If the temperature of any card exceeds the preset threshold of 75ºC (167ºF), then an alarm is generated. The show chassis

CLI command displays the problem; check the Over Temperature state value, which will show

“Out of range”.

If the temperature inside the chassis becomes high enough to damage a card or the system, safety mechanisms are activated until a safe operating level is reached. Normal operating conditions do not activate any safety mechanisms. Safety mechanisms include shutting down a card until its temperature returns to an operationally safe value, at which time the card resets and returns to service.

If the FAN LED is amber (indicating a fan problem), a Fan Fail Alarm or a Temperature

Threshold Alarm is raised and the Fan module should be replaced.

7705 SAR-8 Installation Guide Page 45

7705 SAR-8 Components

Distribution Panels

Distribution panels are used with 16-port T1/E1 ASAP Adapter cards to connect to T1/E1 circuits.

There are two distribution panels:

• BNC

• RJ45

Note: The connector on the faceplate of the 16-port T1/E1 ASAP Adapter card is a 68-pin

AMP connector that provides a SCSI-2 interface. Although the connector is sometimes referred to as a SCSI-2 connector, this document refers to it as a 68-pin AMP connector. This naming convention applies to the connector on any T1/E1 cable that attaches to the 16-port

T1/E1 ASAP Adapter card.

BNC Distribution Panel

Figure 10 shows the BNC Distribution panel. Table 3

lists the panel features.

The BNC panel provides 75-ohm E1 access for up to 32 ports. On the customer side, each access port has separate transmit and receive BNC female connectors. On the equipment side, the panel has two sets of 68-pin AMP connectors for connection to two 16-port T1/E1

ASAP cards via 68-pin AMP to 68-pin AMP T1/E1 cables (see T1/E1 Cables on page 48 ).

One set of AMP connectors on the panel is for network ports 1 to 16, and the other set is for network ports 17 to 32.

Note: A set of connectors consists of one MAIN connector and one SPARE connector. When connecting to 16-port T1/E1 ASAP Adapter cards, always use the (bottom) connectors labeled MAIN.

Page 46 7705 SAR-8 Installation Guide

7705 SAR-8 Overview

Figure 10: BNC Distribution Panel

Front

1 2 3 4 5 6 7 8 RX 1 - 8

TX 1 - 8

RX 17-24

TX 17-24

17 18 19 20 21 22 23 24

9 10 11 12 13 14 15 16

RX 9 - 16

TX 9 - 16

RX 25-32

TX 25-32 25 26 27 28 29 30 31 32

Back

1

TX /

SPARE / EXT

RX 17 32 M4

TX / RX

MAIN

17 32 M2

TX /

SPARE /

RX 1 -

EXT

16 M4

TX / RX

MAIN

1 16 M2

1

2

19788

Key

1

2

Table 3: Distribution Panel Features

Description

Label

68-pin AMP connectors

RJ45 Distribution Panel

Figure 11

shows the RJ45 Distribution panel. Table 3

lists the panel features.

The RJ45 panel provides 100-ohm T1 or 120-ohm E1 access to 32 ports. On the customer side, each port has an RJ45 connector. On the equipment side, the panel has two sets of

68-pin AMP connectors for connection to two 16-port T1/E1 ASAP cards via 68-pin AMP to 68-pin AMP T1/E1 cables (see

T1/E1 Cables on page 48

). One set of AMP connectors on the panel is for network ports 1 to 16, and the other set is for network ports 17 to 32.

Note: A set of connectors consists of one MAIN connector and one SPARE connector. When connecting to 16-port T1/E1 ASAP Adapter cards, always use the (bottom) connectors labeled MAIN.

7705 SAR-8 Installation Guide Page 47

7705 SAR-8 Components

1 2

I/O

3 4

9 10

I/O

11 12

5 6

I/O

7 8

13 14

I/O

15 16

Figure 11: RJ45 Distribution Panel

Front

17 18

I/O

19 20

25 26

I/O

27 28

21 22

I/O

23 24

29 30

I/O

31 32

Back

TX /

SPARE

RX 17 -

/ EXT

32 M4

TX / RX

MAIN

17 32 M2

1 2

M3 /

SPARE

TX /

/ EXT

RX 1 - 16

M1 /

MAIN

TX / RX 1 - 16

1

19604

T1/E1 Cables

Installation Guide Name

68-pin AMP connector to open-ended wire

T1/E1 cable

68-pin AMP to 68-pin AMP

T1/E1 cable

Table 4

describes the T1/E1 cables that are available for the 7705 SAR-8, and gives the name used in the various installation guides as well as the name used in the orderable parts catalog.

Table 4: T1/E1 Cables

Orderable Parts Name

T1/E1 Cable 28 AWG Open-ended 30m

T1/E1 Cable 28 AWG Open-ended 15m

T1/E1 Cable 26 AWG Open-ended 30m

T1/E1 Cable 26 AWG Open-ended 15m

Description

• 68-pin AMP connector to openended wire

• for equipment connection to telecom equipment

T1/E1 Cable for Distribution Panel, 1m • 68-pin AMP to 68-pin AMP connectors

• for equipment connection to a distribution panel

For pinout information on the cables listed above, refer to the 7705 SAR 16-port T1/E1

ASAP Adapter Card Installation Guide.

Page 48 7705 SAR-8 Installation Guide

7705 SAR-8 Overview

SAR System Installation Process

To install the 7705 SAR-8 system, perform the installation procedures in the following order:

Step 1.

Prepare the site.

Step 2.

Unpack the chassis.

Step 3.

Mount and ground the chassis.

Step 4.

Prepare and connect the DC input power cables.

Step 5.

Install the components.

Step 6.

Power up the system.

Step 7.

Connect the network cables.

Step 8.

Provision (preconfigure) the system.

7705 SAR-8 Installation Guide Page 49

SAR System Installation Process

Page 50 7705 SAR-8 Installation Guide

Site Preparation

In This Chapter

This chapter provides information about preparing your site to install a 7705 SAR-8:

•

Warnings and Notes on page 52

•

System Specifications on page 54

→

Chassis Specifications on page 54

→

Environmental Specifications on page 54

→

Adapter Card Specifications on page 55

→

CSM Specifications on page 56

→

Fan Module Specifications on page 56

→

Component Power Consumption on page 56

→

Component Operating Requirements on page 57

•

Installation Locations on page 58

→

Chassis Location Requirements on page 59

•

Safety Considerations on page 61

→

Placement on page 61

→

Grounding on page 61

→

Cabling on page 63

→

Power on page 63

→

Fan Module on page 64

→

Storage on page 64

7705 SAR-8 Installation Guide Page 51

Warnings and Notes

Warnings and Notes

Warning:

• Do not transport and relocate a 7705 SAR-8 chassis that has any cards or modules installed. To properly transport and relocate a 7705 SAR-8 chassis, do the following:

→ (optional) label cards and modules to facilitate reassembly

→ remove all CSMs, adapter cards, and the Fan module from the chassis

→ disconnect any connected power cables from the chassis

→ repackage the cards and modules in their original shipping containers for relocation

• The 7705 SAR-8 uses external circuit breakers or fuses as a disconnect means.

Disconnect both A and B feeds before servicing.

• Do not assume that power has been disconnected from a circuit. Be sure to disconnect power to the equipment rack and external cables before installing or removing the

7705 SAR-8.

• Do not install equipment that appears to be damaged.

• 7705 SAR-8 systems equipped with DC-input power supplies should be installed in restricted access areas, such as a dedicated equipment room or an equipment closet, in accordance with Articles 110-16, 110-17, and 110-18 of the National Electric Code

ANSI/ NFPA 70.

• This product complies with, and has been CE marked in accordance with, the European

Directive 99/05/EC (R&TTE) and 2004/108/EC (EMC).

• Failure to comply with the equipment rack and chassis instructions as outlined in

Installation Locations on page 58

and Chassis Location Requirements on page 59

will cause thermal failure.

• The 7705 SAR-8 uses a fiber-optic communications method and is a Class 1 laser product.

Only trained service personnel familiar with laser radiation hazards should install or remove fiber-optic cables and cards in this system.

Notes:

• Prepare the equipment rack and site before installing the router. Plan the router placement near the power sources and network interface connections.

• An empty 7705 SAR-8 chassis weighs approximately 8.5 lbs (3.8 kg).

• A fully loaded 7705 SAR-8 chassis with the heaviest components/cards weighs approximately 15 lbs (6.8 kg).

• Always install the heaviest equipment on the bottom of the rack to keep the center of gravity of the equipment rack as low as possible.

Page 52 7705 SAR-8 Installation Guide

Site Preparation

Notes: (continued)

• To provide necessary stability, ensure that the equipment rack is bolted to the floor. Ceiling brackets are useful to provide additional stability.

• The equipment rack must be properly grounded.

• Install components after the chassis is installed in the rack.

• Maintain a clearance of at least 2.5 in. (6.4 cm) at the front of the router for cable management.

• Maintain a clearance of at least 3 in. (7.6 cm) on each side to ensure adequate air intake and exhaust. When mounting the router in a rack, ensure that the rack complies with all

requirements outlined in Chassis Location Requirements on page 59 .

• The 7705 SAR-8 includes factory-installed rack-mounting brackets to mount in a 19-inch equipment rack.

7705 SAR-8 Installation Guide Page 53

System Specifications

System Specifications

Chassis Specifications

Table 5: 7705 SAR-8 Chassis Specifications

Parameter

Dimensions

(without mounting brackets)

Chassis weight (unpopulated) 8.4 lbs. (3.8 kg)

Chassis weight

(FAM, 2 x CSM, 2 x Ethernet cards, 4 x ASAP cards)

16.1 lbs. (7.3 kg)

Adapter card slots

Fan module slots

6

1

CSM slots

Mounting

Description

(3.50 x 17.48 x 9.84 in.) (H x W x D)

(8.89 x 44.4 x 25 cm)

2

Mount in a recommended 19-inch equipment rack

Rack-mount brackets are factory-installed for 19-inch

NEBS mounting

Environmental Specifications

Table 6: Environmental Specifications

Parameter

Normal operating temperature

Short-term operating temperature

(1)

Relative humidity

Short-term relative humidity

(1)

Altitude range

Description

5 to 45ºC (41 to 113ºF)

-5 to 55ºC (23 to 131ºF)

5 to 85% (non-condensing)

5 to 95%, not to exceed 0.024 lb of water per

1.0 lb of air (35 g of water per 1.0 cubic meter of air)

Between 197 ft. (60 m) below sea level and

5906 ft. (1800 m) above sea level (70kPa to

106kPa)

Page 54 7705 SAR-8 Installation Guide

Site Preparation

Parameter

Shock and vibration

Earthquake

Pollution degree

Table 6: Environmental Specifications (Continued)

(2)

Rated voltage (DC)

Description

Very low levels for continuous duration (similar to modern office building, for example)

Suitable for high risk areas (Zone 4/California, for short duration)

2

Operating voltage range (DC)

Heat dissipation (worst case configuration)

-48/-60 VDC (-60 VDC is for various European countries)

-40 to -75 VDC

190 Watts

Notes:

1. Short-term is a period of less than 96 consecutive hours and a total of no more than 15 days per year. This is equivalent to 360 hours per year, with short-term periods occurring no more than 15 times per year.

2. Pollution degree is as defined in IEC 60950.

Adapter Card Specifications

Table 7: Adapter Card Specifications

Parameter

Dimensions (H x W x D)

Weight

Description

(6.69 x 0.88 x 8.66 in.)

(17.0 x 2.24 x 22.0 cm)

0.84 lbs (0.38 kg) (16-port T1/E1 ASAP card)

0.77 lbs (0.35 kg) (8-port Ethernet card)

7705 SAR-8 Installation Guide Page 55

System Specifications

CSM Specifications

Parameter

Dimensions (H x W x D)

Weight

Table 8: CSM Specifications

Description

(6.69 x 0.88 x 8.66 in.)

(17.0 x 2.24 x 22.0 cm)

0.88 lbs (0.4 kg)

Fan Module Specifications

Table 9: Fan Module Specifications

Parameter

Dimensions (H x W x D)

Weight

Description

(3.32 x 0.88 x 8.66 in.)

(8.43 x 2.24 x 22.0 cm)

0.81 lbs (0.37 kg)

Component Power Consumption

Table 10: Component Power Consumption

Component Power (Watts)

(conservative estimate)

28 W

Chassis

(1)

(all fans operating, no adapter cards)

Fan module 28 W

Adapter cards a16-chds1 a8-eth

17 W

20 W

Note:

1. In Release 1.0, the chassis itself consumes no power because an external DC power supply provides system power. Thus, power consumption of the chassis with all fans operating is equivalent to the power consumption of the Fan module.

Page 56 7705 SAR-8 Installation Guide

Site Preparation

Refer to the 7705 SAR-8 adapter card installation guide s for more information on these components.

Component Operating Requirements

Table 11: 7705 SAR-8 Hardware Components for DC Operational Requirements

Component Minimum

Backplane (factory-installed) 1

Maximum

1

Field-Replaceable

N

Fan module

Adapter cards

DC power harness (1)

1

1

1

6

1 2

Y

Y

Y

Note:

1. DC power harnesses are available from Alcatel-Lucent. Each harness has two wires. Use two harnesses when redundant DC supplies are used. All power cables used on the 7705 SAR-8 chassis must meet your local safety codes.

7705 SAR-8 Installation Guide Page 57

Installation Locations

Installation Locations

The 7705 SAR-8 is intended to be installed in facilities that provide weather protection and a temperature-controlled environment. The facilities provide protection from mold growth, pest incursion, and precipitation. The 7705 SAR-8 is not intended for installation in outdoor facilities.

Warning: Follow the equipment rack manufacturer’s instructions for proper rack installation.

Failure to comply with the requirements and the location requirements outlined in this section and

Chassis Location Requirements on page 59 will impede proper airflow and will result in

the system overheating.

Airflow on the 7705 SAR-8 is defined as EC Class (S) SR-SL per GR3028. For proper thermal performance, the following conditions must be met.

• The rack must be constructed using channel or angle rack uprights that are at least

1.25 in. (3.2 cm) deep, 3 in. (7.6 cm) wide (maximum), and oriented away from the chassis such that no solid metal from the uprights is located immediately adjacent to the chassis side walls (see

Figure 12

).

Example: Telect 02008-02011 Series or Newton 0040140XXX Relay Racks.

• The rack must not be an unequal flange rack that has solid walls located immediately adjacent to the chassis side walls. This will cause thermal failure.

Example: Telect 02033-02036 series.

• For seismic applications, the rack must be a Telect Global Seismic Frame

(GS series).

• 7705 SAR-8 deployments in closed cabinets are not recommended. If closed cabinets must be used, they must not restrict shelf airflow in any way. Furthermore, they must not cause the shelf inlet bulk air temperatures to rise above those defined in GR-63 under worst case environmental conditions, including any preheating of the cabinet air by other equipment.

• The rail mounting holes in the equipment rack must align with the mounting holes on the chassis mounting brackets. The 7705 SAR-8 mounting brackets are factoryinstalled for a NEBS mount in a 19-inch rack.

Follow the equipment rack manufacturer’s instructions for proper rack installation.

Page 58 7705 SAR-8 Installation Guide

Site Preparation

Required tools:

• #2 Phillips screwdriver

• flathead screwdriver

• anti-static bags, mats, and packaging

• ESD wrist strap

Chassis Location Requirements

Allow at least 3 in. (7.6 cm) clearance on the sides of the chassis for proper airflow and at

least 2.5 in. (6.4 cm) in front for cable management. See Figure 12 .

Warning: Failure to comply with the location requirements outlined in

Installation Locations on page 58

and Chassis Location Requirements on page 59

will impede proper airflow and will result in thermal failure.

Note: The Fan module provides 120 CFM of airflow through the 7705 SAR-8 (8 fans at

14.8 CFM/fan).

Observe the following requirements when installing the system.

• Ensure that the chassis is located in an area that can provide an average inlet air temperature (bulk air temperature averaged over 1 year) no greater than 104°F

(40°C) under full system power loading combined with worst-case environmental deployment conditions per GR-63.

• Ensure that the 7705 SAR-8 system intake is not located immediately adjacent to the exhaust of another chassis such that preheated air above 40°C long term or 55°C short term (per GR-63) is drawn into the system.

• Ensure that the 7705 SAR-8 system intake is not located immediately adjacent to the intake of another chassis such that 7705 SAR-8 airflow is restricted in any way.

• Ensure that the inlet and exhaust of the chassis is free of obstructions from cabling,

mounting hardware, or other electronic equipment in the areas shown in Figure 12 .

7705 SAR-8 Installation Guide Page 59

Installation Locations

Figure 12: Chassis Clearance Requirements (View from Top)

2 Rear

3 3

2

3

Key

1

4

4

1

Front

4

Rack upright

19765

Table 12: Chassis Clearance Specifications

Description

Front: 2.5 in. (6.4 cm) required for cable management

Rear: No clearance required

Side: 3 in. (7.6 cm) minimum required for airflow

Rack upright: 5 in. (12.7 cm) maximum required for airflow

Page 60 7705 SAR-8 Installation Guide

Site Preparation

Safety Considerations

Placement

Warning:

• Install the 7705 SAR-8 in recommended equipment racks.

• Install in clean, dry, ventilated, and temperature-controlled rooms.

• Verify that the rack is properly bolted and braced and is properly grounded to a grounding electrode.

• Install the chassis in the equipment rack before installing components.

Grounding

Warning:

• The router and equipment rack must be properly grounded. Chassis ground cables are not included. Lack of proper grounding (earthing) of the equipment may result in a safety hazard and excessive electromagnetic emissions.

• Electrostatic discharge (ESD) damage can occur if components are mishandled. Always wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is connected to site grounding point (typically, the grounding stud on the 7705 SAR-8 , or a properly grounded rack or work bench).

• The 7705 SAR-8 includes a chassis ground stud on the mounting bracket attached to the right-hand side of the router (when viewed from the front). The chassis ground must be connected to the building ground, using either a direct connection or a ground bus.

• Before making the chassis ground connection, ensure that all power is OFF from the DC circuit. To switch the power OFF, locate the circuit breaker on the panel board that services the DC circuit and switch the circuit breaker to the OFF position.

Tip: For extra safety, you can tape the handle of the circuit breaker in the OFF position.

• Do not use the chassis ground wire connection on the chassis ground stud for any other purpose. That is, the washers and nut used to secure the chassis ground wire on the ground stud must only be used for that purpose.

• When wiring the unit, the chassis ground connection must always be made first and disconnected last.

7705 SAR-8 Installation Guide Page 61

Safety Considerations

The

7705 SAR-8

supports both Common Bonding Networks (CBN) and Isolated Bonding

Networks (IBN). The positive battery inputs (Batt A and Batt B) are floating inputs relative to digital or chassis ground within the chassis and on the CSM, the adapter cards, and the

Fan module.

To use the system in a CBN installation, the 0V RTN terminal must be connected to the frame ground on the rack in which the

7705 SAR-8

is installed. For IBN installations, no additional grounding is needed.

Warning: In an IBN installation, the 0V RTN terminal must be connected to the building ground at the source.

Warning: In a CBN installation, if you use the 7705 SAR-8 chassis ground stud (located on the right-hand side mounting bracket) to connect the 0V RTN terminal to the frame ground on the rack, then you must use a second nut on the stud to secure the attachment. The first nut is used to secure the building ground point wire to the chassis ground lug, which must be a single-purpose permanent connection. Refer to

Chassis Ground Wiring on page 73 .

Page 62 7705 SAR-8 Installation Guide

Site Preparation

Cabling

Warning:

• To comply with the GR-1089-CORE requirement R4-9 [31] standard for electromagnetic compatibility and safety, all intra-building ports are specified for use with cables that are shielded and grounded at both ends.

• To meet surge protection requirements, the shield must be grounded by attaching the shield to a convenient chassis ground point, using hardware suitable to provide a solid electrical and mechanical connection. In addition, ensure that there is sufficient strain relief to remove any mechanical strain on the ground connection due to cable movement.

• The intra-building port(s) of the equipment or sub-assembly is suitable for connection to intra-building or unexposed wiring or cabling only. The intra-building port(s) of the equipment or sub-assembly must not be metallically connected to interfaces that connect to the Outside Plant (OSP) or its wiring. These interfaces are designed for use as intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling. The addition of primary protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.

Connection to external OSP wiring must be made through an external CSU prior to exiting the building.

• Bare conductors must be coated with an appropriate antioxidant compound before crimp connections are made. All unplated connectors, braided strap, and bus bars must be brought to a bright finish and then coated with an antioxidant before they are connected.

• The 7705 SAR-8 is suitable for both DC-I and DC-C power configurations. However, when used in a DC-I configuration, the battery returns must remain isolated until they reach the main power bus.

Power

Danger:

• Only electrical service personnel should perform wiring and cabling to the system.

• All power to the equipment rack or cabinet should be disconnected before the installation.

• Power cable(s) must meet your local electric code requirements.

• An external circuit breaker no greater than 10A must be located within a readily accessible distance from the equipment. This is intended as the disconnect device.

• When removing the DC power harness from the system, first disconnect the power from the source and then disconnect the harness from the 7705 SAR-8.

7705 SAR-8 Installation Guide Page 63

Safety Considerations

DC Power Requirements

• A means of disconnect must be provided within 10 ft (3 m) of the 7705 SAR-8.

• A maximum 10A circuit breaker or fuse must be provided.

• A minimum #18 AWG power conductor must be used for each DC input connection.

Fan Module

The 7705 SAR-8 supports a field-replaceable Fan module housing eight fans. The Fan module is replaceable as a single unit; individual fans are not replaceable.

The 7705 SAR-8 cooling system requires a minimum of 3 in. (7.6 cm) of unrestricted, unobstructed airflow on each side of the chassis to function properly.

Warning:

Failure to comply with the location requirements outlined in Installation Locations on page 58

and in this section will impede proper airflow and will result in thermal failure.

Danger: When removing the Fan module for servicing or any other reason, wait until all fans have stopped rotating before continuing work.

Storage

To store an uninstalled 7705 SAR-8 or extra field-replaceable parts (if applicable), re-wrap the components in the original packaging and keep them in a dry, dust-free temperaturecontrolled environment.

Table 13: Storage Specifications

Parameter Description

Storage and shipping temperature From -40° to 158°F (-40° to 70°C)

Non-condensing relative humidity Within 5 to 95%

Page 64 7705 SAR-8 Installation Guide

Site Preparation

Compliance

Refer to Standards and Protocol Support on page 137 for compliance information.

7705 SAR-8 Installation Guide Page 65

Safety Considerations

Page 66 7705 SAR-8 Installation Guide

Installing the Chassis

In This Chapter

This chapter provides information on installing a 7705 SAR-8 chassis:

•

Unpacking the Chassis on page 68

→

Unpacking Precautions on page 68

•

Installing the Chassis in a Rack on page 70

→

Rack-Mounting the Chassis on page 70

•

Chassis Ground Wiring on page 73

→

Making the Ground Connection on page 73

7705 SAR-8 Installation Guide Page 67

Unpacking the Chassis

Unpacking the Chassis

The Control and Switching Module (CSM), adapter cards, Fan module, and cables are field-

installable and field-replaceable components. Refer to Installing the Components on page 83

for more details. The DC power connectors are part of the 7705 SAR-8 chassis and are not field-replaceable.

Warning:

If the 7705 SAR-8 is to be relocated at a later time, observe the following warning:

• Do not transport and relocate a 7705 SAR-8 chassis that has any cards or modules installed. To properly transport and relocate a 7705 SAR-8 chassis, do the following:

→ (optional) label cards and modules to facilitate reassembly

→ remove all CSMs, adapter cards, and the Fan module from the chassis

→ disconnect any connected power cables from the chassis

→ repackage the cards and modules in their original shipping containers for relocation

Unpacking Precautions

Review the following list to avoid injury and to prevent damage to the 7705 SAR-8.

• The shipping weight of the chassis is approximately 10 lbs. (4.5 kg) without any components installed.

• The chassis is shipped in a heavy corrugated cardboard container protected by foam end caps. Do not discard the packaging container and materials used in shipping.

The packing materials should be re-used if it is necessary to reship the router.

• Keep the chassis wrapped in the anti-static packaging until you are ready to install the router.

Page 68 7705 SAR-8 Installation Guide

Installing the Chassis

Figure 13

displays the components of a packed 7705 SAR-8 chassis.

Figure 13: Unpacking the 7705 SAR-8 Chassis

3

2

3

1

19600

2

3

Key

1

Table 14: Unpacking the 7705 SAR-8 Chassis

Description

Shipping container

7705 SAR-8 chassis (wrapped in an anti-static bag)

Foam end caps

To unpack the chassis, open the carton and follow these steps:

Caution: Lift the chassis by the bottom of the chassis. Do not put your hands inside a card slot to lift the unit.

Step 1.

Carefully lift the router out of the carton and place it on a flat surface.

The chassis shipping weight is approximately 10 lbs. (4.5 kg) without any components installed.

Step 2.

Remove the foam end caps on the sides of the router.

Step 3.

Remove the protective anti-static wrapping when you are ready to install the router.

7705 SAR-8 Installation Guide Page 69

Installing the Chassis in a Rack

Installing the Chassis in a Rack

Danger: Only trained and qualified personnel should install or replace this equipment.

Caution:

• Always wear an ESD-preventive wrist or ankle strap and always connect an ESD strap to a nearby ground point that is connected to the site grounding point (typically, the grounding stud on the 7705 SAR-8, or a properly grounded rack or work bench).

• Lift the chassis by the bottom of the chassis. Do not put your hands inside a card slot to lift the unit.

• When rack-mounting the chassis in an equipment rack, do not stack other 7705 SAR-8 units or any other equipment directly on top (where the bottom unit is supporting other devices). Each unit must be secured in the rack with the appropriate mounting apparatus.

Warning:

• Failure to comply with the location requirements outlined in Installation Locations on page

58

and

Chassis Location Requirements on page 59

will impede proper airflow and will result in thermal failure.

• Non-conductive coatings (such as lacquer and enamel) must be removed from threads and other contact surfaces to ensure electrical conductivity. Thread-forming screws with paint piercing washers may be used for this purpose during installation.

Rack-Mounting the Chassis

The 7705 SAR-8 router chassis is designed for installation in a 19-inch rack. The rack-

mount brackets are factory-installed. Figure 14 illustrates the installation of the chassis in a

rack.

It is easier to install the 7705 SAR-8 chassis in the rack with two people, one person to hold the router and one person to secure it to the rack.

Page 70 7705 SAR-8 Installation Guide

Figure 14: Installing the 7705 SAR-8 Chassis in a Rack

Installing the Chassis

1

3

SLOT ID

CSM A

MDA 1

CSM B

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

CSM

Stat Act

Pwr

Mgmnt Port

A16-CND31

Stat Act

Pwr

Port

Console

Ports 1-16

Sync

In Out

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

2

2

3

Key

1

4

Table 15: Rack-Mounting the 7705 SAR-8 Chassis

Description

Equipment rack

Rack-mounting screws

7705 SAR-8 chassis

Rack-mounting bracket

4

19640

7705 SAR-8 Installation Guide Page 71

Installing the Chassis in a Rack

Before you begin, verify that:

• the equipment rack is securely installed, anchored, and grounded. Refer to the rack manufacturer’s documentation for instructions.

• the power to the rack is OFF

Required tools:

• a torque driver for Phillips screws

To install the chassis in the rack:

Step 1.

Lift the 7705 SAR-8 from the bottom and position it in the rack. If two people are installing the chassis, position one person in front of the rack and one behind it.

Step 2.

Align the mounting holes on each bracket with the mounting holes on the rack rail.

Insert a screw into each mounting hole and tighten.

Step 3.

Ground the chassis to the building ground. See Chassis Ground Wiring (below).

Page 72 7705 SAR-8 Installation Guide

Installing the Chassis

Chassis Ground Wiring

To make sure that the equipment is connected to earth ground, use the following instructions to prepare the ground wire and make the connection. Ground wire is not provided. The length of the ground wire depends on the location of the router and proximity to the proper grounding facilities.

Caution: The 7705 SAR-8 chassis ground stud located on the right-hand side mounting bracket must be a single-purpose permanent connection to the earth (building) ground point.

Therefore, the connection requires its own washers and nut.

Note:

• When wiring the unit, the chassis ground connection must always be made first and disconnected last.

• All bare conductors must be coated with an appropriate antioxidant compound before crimp connections are made. All unplated connectors, braided strap, and bus bars must be brought to a bright finish and then coated with an antioxidant before connecting them.

• All surfaces that are used for intentionally grounding the 7705 SAR-8 must be brought to a bright finish and an antioxidant solution must be applied to the surfaces being joined.

Making the Ground Connection

Tools and hardware required:

• wire stripper

• wire cutter

• crimping tool

• torque driver for hex nut

• M4 ring lug

• minimum #18 AWG wire (green/yellow)

Figure 15: Preparing the Ground Wire

2

3

1

19641

7705 SAR-8 Installation Guide Page 73

Chassis Ground Wiring

2

3

Key

1

Table 16: Ground Wire Descriptions

Description

Copper ground wire with green/yellow shield (minimum #18 AWG)

Insulation stripped according to local safety code

Ring lug

Figure 16: Attaching the Chassis Ground Connector

4 5 6 5 3

3

2

1

Page 74

19599

5

6

3

4

Key

1

2

Table 17: Chassis Ground Connection

Description

Lance

Cable tie

Chassis ground stud

Nut

Star washer

Ring lug and chassis ground wire (green/yellow)

7705 SAR-8 Installation Guide

Installing the Chassis

To make the chassis ground connection:

Step 1.

Run a single length of minimum #18 AWG wire from the ground point (building ground or equipment ground bus) to the chassis ground stud. When routing the cable, ensure that there is enough extra wire to form a service loop at the chassis end in order to facilitate maintenance.

Step 2.

Using a wire-stripping tool, strip the insulation from the wire according to local

safety codes and crimp the ring lug to the wire ( Figure 15 ).

Step 3.

Remove the nut and star washers from the ground stud on the mounting bracket.

Step 4.

Place a star washer and the ring lug on the ground stud such that the wire runs down

the rack upright. Secure the lug with the second star washer and nut ( Figure 16 ).

Tighten the nut to a torque of 8-10 lbf-in. maximum. Do not over-tighten.

Step 5.

Use a cable tie to secure the ground wire to the lance on the mounting bracket.

Step 6.

Form a service loop with the extra wire and secure it to a convenient place (for example, a rack upright).

Step 7.

Connect the opposite end of the ground wire to the appropriate ground point at your installation site. Ensure that the chassis ground connection is made according to local safety codes.

Step 8.

Connect the 7705 SAR-8 to the DC power source. See DC Power Connections on page 77

.

7705 SAR-8 Installation Guide Page 75

Chassis Ground Wiring

Page 76 7705 SAR-8 Installation Guide

DC Power Connections

In This Chapter

This chapter provides information about wiring and connecting the DC power source to the

7705 SAR-8 :

•

Wiring and Connecting DC Power on page 78

→

Warnings and Notes on page 78

•

DC-Input Power Connections on page 79

→

Wiring the DC Inputs on page 79

7705 SAR-8 Installation Guide Page 77

Wiring and Connecting DC Power

Wiring and Connecting DC Power

Warnings and Notes

Danger:

• Make the ground connections first.

• Only qualified personnel should install or replace this equipment.

• Confirm that the DC power source is OFF during installation. The power source should be a safety extra-low voltage (SELV) source.

• Turn off power at the power source before you install or remove power cables or cords.

• The unit should be connected to a DC branch circuit with a maximum 10A circuit breaker or fuse that meets the requirements for branch circuit protection. A suitable disconnect device must be provided in the DC branch, either a circuit breaker or switch that can be employed to disconnect power to the system during servicing.

• Before working on equipment that is connected to power, remove jewelry, such as rings, necklaces, and watches. When metal objects are in contact with power and ground, serious burns can occur or the objects can be welded to the terminals.

• You must use cables that meet local electrical code requirements.

Warning:

• Do not install equipment that appears to be damaged.

• The router and equipment rack must be properly grounded. Electrostatic discharge (ESD) damage can occur if components are mishandled.

• Always wear an ESD-preventive wrist or ankle strap and always connect an ESD strap to a nearby ground point that is connected to the site grounding point (typically, the grounding stud on the 7705 SAR-8, or a properly grounded rack or work bench).

• The 0V RTN terminal must always be connected to the building ground at the source.

• If the disconnect device for the 7705 SAR-8 is not permanently incorporated, a readily accessible disconnect device to shut off power during servicing must be incorporated in your building’s branch circuit.

Page 78 7705 SAR-8 Installation Guide

DC Power Connections

Note:

• The 7705 SAR-8 requires a minimum of one DC power source to operate, but using two

DC power sources is recommended for redundancy.

• The 7705 SAR-8 is suitable for both DC-I and DC-C power configurations.

• All bare conductors must be coated with an appropriate antioxidant compound before crimp connections are made. All unplated connectors, braided strap, and bus bars must be brought to a bright finish and then coated with an antioxidant before connecting them.

• To comply with the GR-1089-CORE requirement R4-9 [31] standard for electromagnetic compatibility and safety, all intra-building ports are specified for use with cables that are shielded and grounded at both ends.

DC-Input Power Connections

Warning:

• Ensure that all power is OFF from the DC circuit. Locate the circuit breaker on the panel board that services the DC circuit and switch the circuit breaker to the OFF position. For extra safety, you can tape the handle of the circuit breaker in the OFF position.

• When wiring the unit, the chassis ground connection must always be made first and disconnected last.

Wiring the DC Inputs

The

7705 SAR-8

has two D-Sub 2W2 connectors mounted on the front of the chassis. These connectors are the DC power feed points for DC source voltage from the DC circuit. A 13 ft

(4 m) wiring harness is available from Alcatel-Lucent to facilitate the DC source-to-router connection. The harness has a 2W2 connector at one end and open-ended wires at the other end.

For redundant power configurations, you must use two DC power feeds (one for each power connector on the 7705 SAR-8).

7705 SAR-8 Installation Guide Page 79

DC-Input Power Connections

Page 80

Each 2W2 connector is keyed to ensure proper attachment (one female and one male pin) and is secured with thumbscrews on the harness connector to prevent accidental removal.

Figure 17

shows the DC power harness.

Figure 17: DC Power Harness

2

2

1

1

19601

Key

1

2

Table 18: DC Power Connection Descriptions

Description

0V RTN (male pin on chassis, black wire, #12 AWG)

-VDC (female pin on chassis, blue wire, #12 AWG)

Required tools and hardware:

• one or two DC power wiring harnesses (3HE03400AA) (two harnesses are required for redundant power configurations)

• torque driver for slot screws

Follow these steps to wire and connect a DC power feed:

Step 1.

Ensure power has been disconnected from the DC power source end. Typically, this is done via a circuit breaker or another disconnect device.

Step 2.

Prepare the DC power harness at the DC power source end. Strip the wire insulation to the proper length according to your local safety codes.

Step 3.

Attach the -VDC (blue) and RTN (black) wires at the DC power source end according to local safety codes.

Step 4.

At the chassis end, attach the 2W2 connector on the wiring harness to the connector on the chassis.

Step 5.

Use a slot screwdriver to secure the chassis connection by tightening the screws on the 2W2 connector.

7705 SAR-8 Installation Guide

DC Power Connections

Step 6.

Secure the power harness to a rack upright within 6 inches (15.25 cm) of the power connection with a cable tie.

Step 7.

For redundant configurations, repeat steps 2 through 6 for the second DC power source.

Step 8.

Install the other

7705 SAR-8

components. See

Installing the Components on page 83 .

7705 SAR-8 Installation Guide Page 81

DC-Input Power Connections

Page 82 7705 SAR-8 Installation Guide

Installing the Components

In This Chapter

This chapter provides information about installing the components in the 7705 SAR-8:

•

Installing Components on page 84

→

Warnings and Notes on page 84

→

CSM on page 84

→

Fan Module on page 86

→

Adapter Cards on page 88

→

SFPs on page 90

•

Installing a Distribution Panel in a Rack on page 92

→

Rack-Mounting a BNC or RJ45 Distribution Panel on page 92

•

Managing Cable Connections to Adapter Cards on page 95

→

Warnings and Notes on page 95

→

Ethernet and Copper Cables on page 96

→

Fiber Cables on page 97

→

Making a Shield Ground Connection on page 98

•

Making External Synchronization Connections on page 99

→

Connecting an External Synchronization Input on page 100

→

Providing an External Synchronization Output on page 100

7705 SAR-8 Installation Guide Page 83

Installing Components

Installing Components

The Control and Switching Module (CSM), adapter cards, Fan module, distribution panel, and cables are field-installable and field-replaceable components.

Warnings and Notes

Danger:

• Only trained and qualified personnel should install or replace this equipment.

• Use of procedures other than those specified in this Installation Guide can result in hazardous radiation exposure.

• Invisible laser radiation can be emitted from an adapter card aperture port when no cable is connected. Avoid exposure and do not stare into open apertures.

Warning:

• Electrostatic discharge (ESD) damage can occur if adapter cards are mishandled.

Always wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is connected to site grounding point (typically, the grounding stud on the

7705 SAR-8

, or a properly grounded rack or work bench).

• Always place components on an anti-static surface.

• Do not power up a 7705 SAR-8 until all components are installed and verified as having been installed correctly.

• Use only approved small form-factor pluggable (SFP) fiber-optic devices in adapter card ports.

Note:

• Ports cannot be configured until the adapter card is provisioned.

• Services cannot be configured until the ports are configured.

CSM

The CSM includes one compact flash memory device that can be used to copy and store system boot, software images, and configuration files and logs. The CSM is shipped with the compact flash memory device installed. The CSM provides the console and management interfaces to the 7705 SAR-8, as well as external synchronization input and output interfaces.

Page 84 7705 SAR-8 Installation Guide

Installing the Components

To maintain EMC compliance, cables that are shielded and grounded at both ends must be used with the Console, (Ethernet) Management, and Synchronization interfaces.

The 7705 SAR-8 cannot boot without a CSM installed. CSMs are installed in slots A and B.

Install a CSM in slot A for a simplex control configuration. Install two CSMs — one in slot A and another in slot B —

for a redundant control configuration. Figure 18 illustrates the

installation of a CSM in slot A.

Refer to CSM Connectors and LEDs on page 112

for a description of the CSM LEDs.

Refer to Replacing a CSM on page 119 for instructions on replacing a CSM.

Figure 18: Installing the CSM

CSM

Stat

Act

Pwr

Mgmnt Port

Console

MDA 1

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

Sync

In Out

CSM

Stat Act

Pwr

Sync

In Out

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19603

2

3

Key

1

4

Table 19: CSM Installation Features

Description

CSM card

Slot guide

Captive screw

Ejector lever

Tools required:

• torque driver for Phillips screws

7705 SAR-8 Installation Guide Page 85

Installing Components

To install a CSM:

Step 1.

Remove the new CSM from the packaging. Do not touch the printed circuit board or connector pins.

Step 2.

Install the CSM. For simplex configurations, the CSM must be installed in slot A. For redundant configurations, install a CSM in slot A and in slot B.

With the ejector levers rotated inward, hold the CSM by the levers, align the card with the slot guides, and slide the card inward until the connectors are seated in the backplane and the faceplate is flush with the front of the chassis.

Note: If the CSM does not seat properly in the backplane, an ejector lever may not be completely rotated inward. Pull the card out half way, adjust the levers, and reinsert the card.

Step 3.

Secure the card in place by tightening the captive screws. Do not over-tighten. The recommended torque is 4-6 lbf.-in.

Note: The CSM cannot be removed if the captive screws are tightened. To remove the CSM, loosen the captive screws, rotate the ejector levers outward to loosen the backplane connectors, and pull the CSM out of the slot.

Fan Module

The Fan module has eight fans mounted on its circuit board. The Fan module must always be installed and fully operational while the 7705 SAR-8 is powered up. During routine maintenance and Fan module replacement, the system can operate safely for up to four

minutes without the Fan module installed. Figure 19 illustrates the installation of the Fan

module.

To maintain EMC compliance, cables that are shielded and grounded at both ends must be used with the Alarm interface.

Refer to

Fan Module Connectors and LEDs on page 114

for a description of the Fan module

LEDs.

Refer to Replacing the Fan Module on page 127

for information on replacing the Fan module.

The Fan module provides an alarm interface equipped with relays that can be used to trigger external alarm indicators. It also provides inputs that can be used to trigger the generation of alarms on the 7705 SAR-8 that indicate environmental or external alarm conditions. Refer to

External Alarms Port Pinouts on page 135

for pinout definitions.

Page 86 7705 SAR-8 Installation Guide

Installing the Components

Warnings and Notes

Warning:

• Always keep your fingers away from rotating fan blades.

• The Fan module is hot-swappable. The 7705 SAR-8 operates safely for up to four minutes while you replace the Fan module. If a longer maintenance time is required, power off the system to prevent over-heating conditions.

Note: In the event of a single fan failure, the remaining fans continue to run. This is sufficient to continue to provide adequate cooling for the system but the Fan module needs to be replaced as soon as possible. The individual fans are not field-replaceable.

Figure 19: Installing the Fan Module

1

SLOT ID

MDA 1

MDA 3

CSM B

MDA 2

MDA 5

MDA 4

MDA 6

Fan

Batt A

Batt B

7705 SAR-8

Alarms

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

2

3

19642

2

3

Key

1

Table 20: Fan Module Installation Features

Description

Slot guide

Captive screw

Threaded receptacle

7705 SAR-8 Installation Guide Page 87

Installing Components

Tools required:

• torque driver for Phillips screws

To install a Fan module:

Step 1.

Remove the Fan module from the packaging and place it on a flat anti-static work surface. Avoid touching the board components and connector pins.

Step 2.

Insert the Fan module into the Fan slot. Align the Fan module with the slot guides and the captive screw with the threaded receptacle.

Step 3.

Press the Fan module firmly into the slot. Make sure that the connectors are fully seated in the receptacle.

Step 4.

Secure the Fan module to the chassis, using a calibrated torque screwdriver set at

4-6 lbf.in. Do not over-tighten.

Adapter Cards

The 7705 SAR-8 system supports the following adapter cards:

• 16-port T1/E1 ASAP Adapter card

• 8-port Ethernet Adapter card

A maximum of up to six adapter cards may be installed on the 7705 SAR-8 in slots MDA 1 through MDA 6 (up to six 16-port T1/E1 ASAP Adapter cards or up to two 8-port Ethernet

Adapter cards). See Figure 5 on page 41

for slot identification. Figure 20

illustrates the installation of an adapter card.

The 8-port Ethernet Adapter card has two small form-factor pluggable (SFP) ports for

Gigabit Ethernet connections and six RJ45 ports for 10/100 BASE-T Ethernet connections.

For more information on installing an SFP, see SFPs on page 90

.

To maintain EMC compliance, cables that are shielded and grounded at both ends must be used with the adapter card interfaces. Use CAT5 shielded cables with Fast Ethernet interfaces and CAT5E shielded cables with Gigabit Ethernet interfaces.

Page 88 7705 SAR-8 Installation Guide

Installing the Components

Refer to Replacing Adapter Cards on page 122

for general information on replacing an adapter card. For information on replacing a specific adapter card, as well as information on its connectors and LEDs, refer to the appropriate adapter card installation guide .

Figure 20: Installing an Adapter Card

1

2

MDA 1

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

A16-CND31

Stat

Act

Pwr

Port

Ports 1-16

3

4

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

External

Alarms

FAN

4

3

19643

3

4

Key

1

2

Table 21: Adapter Card Installation Features

Description

Slot guide

Threaded receptacle

Captive screw

Ejector lever

Tools required:

• torque driver for Phillips screws

To install an adapter card:

Step 1.

Remove the adapter card from the packaging and place on a flat anti-static work surface. Avoid touching board components and connector pins.

With the ejector levers rotated inward, hold the adapter card by the levers, align the card with the slot guides, and slide the adapter card into the slot (see

Figure 20 ).

Note: If the adapter card does not seat properly in the backplane, an ejector lever may not be completely rotated inward. Pull the card out half way, adjust the levers, and reinsert the card.

7705 SAR-8 Installation Guide Page 89

Installing Components

Step 2.

Press the adapter card firmly into the slot. Make sure that the card connectors are seated in the backplane connectors and the faceplate is flush with the front of the chassis.

Step 3.

Tighten the captive screws to secure the card. Do not over-tighten. The recommended torque is 4-6 lbf.-in.

Note: The adapter card cannot be removed if the captive screws are tightened. To remove the adapter card, loosen the captive screws, rotate the ejector levers outward, and pull the adapter card out of the slot.

SFPs

A small form-factor pluggable (SFP) module can be installed on the following adapter cards:

• 8-port Ethernet Adapter card

Figure 21

illustrates the installation of an SFP. Refer to the appropriate adapter card installation guide for more information on SFPs and a list of available types supported by the adapter card.

Figure 21: Installing an SFP

SLOT ID

CSM A

MDA 1

MDA 3

CSM B

MDA 2

MDA 4

MDA 5 MDA 6

CSM

Stat

Act

Pwr

Mgmnt Port

A16-CHDS1

Stat Act

Pwr Port

Console

Ports 1-16

Sync

In Out

A8-ETN

Stat

Pwr

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link

Act Link

Act

7

CSM

Stat Act

Pwr

Mgmnt Port

A16-CHDS1

Stat Act

Pwr Port

A16-CHDS1

Stat Act

Console

Ports 1-16

Sync

In Out

A8-ETN

Pwr Port

Stat

Pwr

Ports 1-16

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link

Act Link

Act

7

8

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

1

Link 5 Act

Link 6 Act

Link

Act

7

Link

8

2

19667

Page 90 7705 SAR-8 Installation Guide

Installing the Components

Key

1

2

Description

SFP receptacle

SFP

Table 22: SFP Installation Features

To install an SFP:

Step 1.

Remove the SFP from the packaging and place it on a flat anti-static work surface.

Avoid touching any SFP components and connector pins.

Step 2.

Insert the SFP into the appropriate receptacle on the adapter card until it clicks in place.

7705 SAR-8 Installation Guide Page 91

Installing a Distribution Panel in a Rack

Installing a Distribution Panel in a Rack

Danger: Only trained and qualified personnel should install or replace this equipment.

Caution: When rack-mounting the distribution panel in an equipment rack, do not stack another panel or any other equipment directly on top of the panel. Each panel must be secured in the rack with the appropriate mounting apparatus.

Rack-Mounting a BNC or RJ45 Distribution Panel

The distribution panel is designed for installation in a 19-inch rack. Figure 22 illustrates the

installation of a distribution panel.

Note: There should be at least 1 RU of space above and/or below the 7705 SAR-8 to run cables from the faceplate connectors. It is not necessary for the space to be immediately above or below the 7705 SAR-8.

Figure 22: Installing a Distribution Panel in a Rack

1

3

1 2

I/O

3 4

9 10

I/O

11 12

5 6

I/O

7 8

13

14

I/O

15 16

2

17 18

I/O

19 20

25

26

I/O

27

28

21 22

I/O

23 24

29 30

I/O

31 32

4

19605

Page 92 7705 SAR-8 Installation Guide

Installing the Components

2

3

Key

1

4

Table 23: Rack-Mounting the Distribution Panel

Description

Equipment rack

Rack-mount screws

Distribution panel

Rack-mount bracket

Before you begin, verify that:

• the equipment rack is securely installed, anchored, and grounded. Refer to the rack manufacturer’s documentation for instructions.

• the power to the rack is OFF

Tools required:

• torque driver for Phillips screws

To install a distribution panel in the rack:

Step 1.

Attach the rack-mount brackets to the panel as shown in

Figure 22

.

Step 2.

Lift the panel and position it in the rack. Ensure that there is at least 1 RU of empty space above or below the 7705 SAR-8 to run cables. See

Managing Cable

Connections to Adapter Cards on page 95 .

Step 3.

Align the mounting holes on each bracket to the mounting holes on the rack uprights.

Insert a screw into each mounting hole and tighten.

Step 4.

Ground the panel to the building ground using one of the methods described below.

a)

If a ground stud is present on the panel, see Chassis Ground Wiring on page 73

.

Warning: Some panels have a grounding tab riveted to the side of the chassis. Do not use the ground tab to make the building ground connection because it does not conform to GR-1089-CORE specifications. Using the grounding tab may result in equipment damage or loss of data.

7705 SAR-8 Installation Guide Page 93

Installing a Distribution Panel in a Rack b) Alternatively, the panel may be grounded to the rack through its mounting screws while adhering to the following requirements.

→ All surfaces that are used for intentionally grounding the panel must be brought to a bright finish and an antioxidant solution must be applied to the surfaces being joined.

→ Non-conductive coatings (such as lacquer and enamel) must be removed from threads and other contact surfaces to ensure electrical conductivity. Threadforming screws with paint piercing washers may be used for this purpose during installation.

Page 94 7705 SAR-8 Installation Guide

Installing the Components

Managing Cable Connections to Adapter Cards

All cable connections to adapter cards are made from the front of the 7705 SAR-8 . The adapter cards can be connected using Ethernet, copper, or fiber-optic cables. A distribution panel is needed to make coaxial cable connections. Refer to the appropriate adapter card installation guide for details on connecting to a specific adapter card.

Note:

• Alcatel-Lucent recommends leaving at least 1 RU of space above and/or below the

7705 SAR-8 to run cables from the faceplate connectors. It is not necessary for the space to be immediately above or below the 7705 SAR-8.

• Ensure cables are dressed such that they do not impede the insertion or removal of fieldreplaceable units (FRUs), such as CSMs, adapter cards, and the Fan module.

• To maintain EMC compliance, cables that are shielded and grounded at both ends must be used with the adapter card interfaces.

• To meet surge protection requirements, the cable shield must be grounded by attaching the shield to a convenient chassis ground point, using hardware suitable to provide a solid electrical and mechanical connection. In addition, ensure that there is sufficient strain relief to remove any mechanical strain on the ground connection due to cable movement.

Warnings and Notes

Danger: Only trained and qualified personnel should install or replace this equipment.

Warning:

• Electrostatic discharge (ESD) damage can occur if CSMs or adapter cards are mishandled. Always wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is connected to site grounding point (typically, the grounding stud on the

7705 SAR-8, or a properly grounded rack or work bench).

• Invisible laser radiation can be emitted from the adapter card aperture ports when no cable is connected. Avoid exposure and do not stare into open apertures.

• Do not power up a 7705 SAR-8 until all components are installed and verified as having been installed correctly.

• Use only approved small form-factor pluggable (SFP) fiber-optic devices in adapter card ports.

7705 SAR-8 Installation Guide Page 95

Managing Cable Connections to Adapter Cards

Ethernet and Copper Cables

Figure 23

illustrates how Ethernet and copper wire cables are routed on the

7705 SAR-8

.

Cables can be routed under or over the chassis.

Figure 23: Managing Cable Connections

A8-ETN

Stat

Pwr

Link 1 Act Link 2 Act

Link 3 Act Link 4 Act Link 5 Act

Link 6 Act

Link Act Link Act

7

A8-ETN

Stat

Pwr

Link 1 Act Link 2 Act

Link 3 Act Link 4 Act

Link 5 Act Link 6 Act

Link Act Link

Act

7 8 FAN

SLOT ID

CSM A

MDA 1

MDA 3

CSM B

MDA 2

MDA 4

MDA 5 MDA 6

CSM

Stat

Act

Pwr

Mgmnt Port

A16-CHDS1

Stat Act

Pwr Port

Console

Ports 1-16

Sync

In Out

A8-ETN

Stat

Pwr

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link Act

Link

Act

7

CSM

Stat Act

Pwr

A16-CHDS1

Stat

Act

Mgmnt Port

Console

Pwr Port

A16-CHDS1

Stat

Act

Pwr

Port

A8-ETN

Stat

Pwr

Ports 1-16

Ports 1-16

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

7

Sync

In

Out

Link Act

Link

Act

8

SLOT ID

CSM A

MDA 1

CSM B

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

CSM

Stat Act

Pwr

Mgmnt Port

Console

Sync

In Out

CSM

Stat Act

Pwr

Mgmnt Port

Console Sync

In

Out

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19668

Hardware required:

• cable ties

To attach Ethernet and copper wire cables:

Step 1.

Attach the cable to the connector on the adapter card.

Step 2.

Route the cables under or over the chassis. If desired, loosely bundle the cables from each slot together using a cable tie. Do not over-tighten the cable tie.

Note: Dress the cables such that they do not impede the insertion or removal of field-replaceable units, including the Fan module.

Step 3.

Attach the cable to a distribution panel or appropriate connector.

Page 96 7705 SAR-8 Installation Guide

Installing the Components

Fiber Cables

Warning:

• Fiber cables are sensitive to bending, twisting and general over-exertion. Extreme caution is recommended when handling fiber cable.

• In order to ensure that the minimum fiber bend radius of 1.2 in. (30 mm) is maintained within the allowable space, an open-angled 90º boot such as TYCO 1374737-x or equivalent is recommended. The boots must be installed and oriented during fiber termination.

• Observe proper fiber connector handling with respect to the use of dust covers and cleaning.

Fiber-optic cables are routed in a similar fashion to Ethernet and copper wire cables (see

Figure 23

). Cables are routed under or over the chassis.

Hardware required:

• fiber cable boot (optional)

• cable ties (optional)

To attach fiber cables:

Step 1.

Attach the cable to the connector on the adapter card. If necessary, attach the fiber cable boot according to the manufacturer’s instructions.

Warning: Fiber cables are sensitive to bending, twisting and general overexertion. Extreme caution is recommended when handling fiber cable.

Step 2.

Route the cables under or over the chassis. If desired, loosely bundle the cables from each slot together using a cable tie. Do not over-tighten the cable tie.

Note: Dress the cables such that they do not impede the insertion or removal of field-replaceable units, including the Fan module.

Step 3.

Attach the fiber cable to a distribution panel or appropriate connector.

7705 SAR-8 Installation Guide Page 97

Managing Cable Connections to Adapter Cards

Making a Shield Ground Connection

To maintain EMC compliance, cables that are shielded and grounded at both ends must be used with the CSM, Fan module, and adapter card interfaces.

To meet surge protection requirements, the cable shield must be grounded to a convenient chassis ground point, such as the equipment rack.

Hardware required:

• wire stripper

• hardware for making the connection (such as a screw, star washer, and cable ties)

To make a shield ground connection:

Step 1.

Locate a convenient chassis ground point, such as the equipment rack.

Step 2.

Carefully strip enough insulation (outer jacket) off of the cable such that the exposed grounding wire can reach the chassis ground point. Ensure that there is enough stipped insulation to provide strain relief for the ground connection.

Caution: When stripping the cable insulation, avoid nicking the ground conductors or the insulation on the signal conductor. Nicks can weaken or break a conductor or expose a wire to a potential short circuit.

Step 3.

Separate the ground shield (braid, foil, and drain wire) from the signal conductors.

Step 4.

Securely attach the shield to the chassis ground point. Use a screw and star washer large enough to make a proper ground connection. Use proper cable dressing and strain relief techniques.

Page 98 7705 SAR-8 Installation Guide

Installing the Components

Making External Synchronization Connections

The CSM provides 1.0/2.3 coaxial connectors for external synchronization input and output.

For redundant CSM configurations, a Y-cable can be used to connect the Sync In connectors on both CSMs to the same external synchronization source. The Y-cable is available from

Alcatel-Lucent.

Figure 24

illustrates the use of a Y-cable for redundant Sync In connections.

Figure 24: Installing Redundant External Synchronization Inputs

1

SLOT ID

CSM A

MDA 1

CSM B

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

CSM

Stat Act

Pwr

Mgmnt Port

A16-CHDS1

Stat

Act

Pwr Port

Console

Ports 1-16

Sync

In Out

A8-ETN

Stat

Pwr

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link

Act Link

Act

7

2

CSM

Stat Act

Pwr

A16-CHDS1

Stat Act

Mgmnt Port

Pwr Port

A16-CHDS1

Stat Act

Pwr Port

A8-ETN

Stat

Console

Ports 1-16

Ports 1-16

Pwr

Link 1 Act

Link 2 Act

Link 3 Act

Link 4 Act

Link 5 Act

Link 6 Act

Link

Act

Link Act

7

Sync

In

Out

8

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

3

4

19602

2

3

Key

1

4

Table 24: Redundant External Synchronization Input Features

Description

Sync In — CSM A

Sync In — CSM B

Y-cable

From external synchronization source

Hardware required:

• coaxial cable with 1.0/2.3 coaxial connector (for single CSM systems)

• Y-cable available from Alcatel-Lucent (for redundant CSM systems)

7705 SAR-8 Installation Guide Page 99

Making External Synchronization Connections

Connecting an External Synchronization Input

To connect an external synchronization source input to the router:

Step 1.

For single CSM systems, attach the synchronization cable to the Sync In connector on the CSM.

For redundant CSM systems, attach the two branch connectors on the Y-cable to the

Sync In connectors on the CSMs — one connector for each Sync In connector.

Step 2.

Attach the other end of the synchronization cable to the external synchronization source.

Providing an External Synchronization Output

To provide an external synchronization source output from the router:

Step 1.

Attach the synchronization cable to the Sync Out connector on the CSM. In a redundant CSM system, either Sync Out connector can be used.

Step 2.

Attach the other end of the synchronization cable to the device requiring a synchronization source.

Page 100 7705 SAR-8 Installation Guide

Initializing and Provisioning

In This Chapter

This chapter provides information about initializing and provisioning the router:

•

Powering Up the Router on page 102

→

Power-Up and Initialization on page 102

→

Troubleshooting Initial Startup on page 103

•

Establishing Router Management Connections on page 105

→

Console Connection on page 105

→

Telnet Connection on page 106

→

Running Telnet on page 107

•

Provisioning CSM and Adapter Card Parameters on page 108

→

Card and Card-Type Commands on page 108

→

MDA and MDA-Type Commands for Adapter Cards on page 109

7705 SAR-8 Installation Guide Page 101

Powering Up the Router

Powering Up the Router

Complete the steps in Wiring the DC Inputs on page 79 and

Installing the Components on page 83

before proceeding with the following instructions. Then power up the system and verify the LED activity of all components.

The primary copy of the 7705 SAR-8 TiMOS software is located on the compact flash memory device that is factory-installed on the CSM. The compact flash device is not fieldreplaceable.

Note:

• The DC-powered 7705 SAR-8 does not have a power switch or circuit breaker. The system is powered on by applying power from the DC power source. Typically, this is done via a circuit breaker or a disconnect device.

• Configurations and executable images can be stored on the compact flash memory device or an FTP file location.

• For proper thermal operation, ensure that slot covers are installed on all empty slots before powering up the router.

• You must have a console or Telnet connection to communicate with and provision the

7705 SAR-8. See

Establishing Router Management Connections on page 105 .

Power-Up and Initialization

To power up the router, follow these steps:

Step 1.

Turn on the power to the router at the remote DC power source(s) to initiate the boot process.

The Power LEDs on the CSM and adapter cards should be blue and the Batt A, Batt

B, and Fan LEDs on the Fan module should be green. If only one DC power source is used, only one Batt LED should be lit.

Step 2.

Verify that the system is initializing.

The system searches the compact flash device on the CSM (cf3) for the boot.ldr

file (also known as the bootstrap or boot loader file). The Status and Activity LEDs on the CSM blink green during initialization. After initialization (approximately 30 seconds), the Status LED and the Activity LED on the active CSM turn solid green; the Activity LED on the inactive CSM continues to blink green.

If the LEDS do not operate as described above, or if they blink and turn off, refer to

Troubleshooting Initial Startup on page 103

.

Page 102 7705 SAR-8 Installation Guide

Initializing and Provisioning

Step 3.

Verify the operational status of the router components by checking all the LEDs on the following components:

→

Fan module (refer to Fan Module Connectors and LEDs on page 114 )

→ CSM (refer to

CSM Connectors and LEDs on page 112

)

→ Adapter cards (refer to the appropriate adapter card installation guide)

Step 4.

After verifying the LEDs, establish communication with the router via the Console port. Refer to

Console Connection on page 105 .

Step 5.

(Optional at this time) Assign an IP address to the CSM. Refer to Telnet Connection on page 106 for quick reference information and to the 7705 SAR OS Basic System

Configuration Guide for detailed information.

Step 6.

(Optional at this time) Configure or modify the primary, secondary, or tertiary BOF file locations. Refer to

Telnet Connection on page 106 for reference information and

to the 7705 SAR OS Basic System Configuration Guide for detailed information.

Troubleshooting Initial Startup

If the system cannot load or cannot find the boot.ldr

file on the compact flash memory device (cf3), the system will continuously reboot in an attempt to successfully find and load the boot.ldr

file. In this happens, the CSM should be replaced and the faulty CSM returned to Alcatel-Lucent. The example below displays the output when the boot.ldr

file cannot be found.

Example: Rebooting display

Rebooting...

Alcatel 7705 Boot ROM. Copyright 2007 Alcatel-Lucent.

All rights reserved. All use is subject to applicable license agreements.

Build: X-0.0.I166 on Wed Aug 8 23:22:35 EDT 2007 by csabuild

Version: 0x1C

Processor core is xxxxXX

COLD boot on processor #1

?Preparing for jump to RAM...

Starting bootrom RAM code...

Boot rom version is v28

>>>Octeon BIST check passed.

>>>Testing SDRAM from 0x02200000 to 0x40000000

>>>Testing Compact Flash ... Slot Empty

Board Serial Number is 'NS073640003'

Platforms in BP EEProm is 0x8

Chassis type 9 (csa8) found in BP EEProm

Chassis Serial Number is 'A60511000005'

Searching for boot.ldr on local drives:

No disk in cf3

No disk in cf3

No disk in cf3

Error - file boot.ldr not found on any drive

Please insert CF containing boot.ldr. Rebooting in 5 seconds.

7705 SAR-8 Installation Guide Page 103

Powering Up the Router

When the system finds the boot.ldr

file, the system processes the initialization parameters from the BOF (boot option file). The BOF should be on the same drive as the boot.ldr

file. If the BOF cannot be found or loaded, then the system prompts the user for alternate image and configuration file locations.

When the image is successfully loaded, control is passed from the boot loader file to the image. The runtime image attempts to locate the configuration file as configured in the BOF.

The configuration file includes chassis, CSM, adapter card, and port configurations, as well as system, routing, and service configurations.

Figure 25

displays the compact flash directory structure and file names.

Figure 25: Files on the Compact Flash

Root bof.cfg

boot.ldr

config.cfg

TiMOS-m.n.Yz

both.tim

Files on the compact flash are:

• bof.cfg — Boot option file

• boot.ldr — Bootstrap image

• config.cfg — Default configuration file

• TiMOS-m.n.Yz: m — Major release number n — minor release number

Y: A — Alpha release

B — Beta release

M — Maintenance release

R — Released software z — Version number both.tim — Application image file

19644

Page 104 7705 SAR-8 Installation Guide

Initializing and Provisioning

Establishing Router Management Connections

There are two ways to access management of the 7705 SAR-8:

• Console connection

• Telnet connection

Console Connection

The console connector on the CSM is a male DB9 connector. To establish a console connection, you need the following:

• an ASCII terminal or a PC running terminal emulation software set to the parameters shown in

Table 25

• a standard serial cable with a female DB9 connector

For pinout information, refer to

Console Port Pinouts on page 133 .

Parameter

Baud Rate

Data Bits

Parity

Stop Bits

Flow Control

Table 25: Console Port Default Settings

Value

115 200

8

None

1

None

CSM

Stat Act

Pwr

Mgmt Port

Figure 26: Console Port Connection

Console port

Console

Sync

In Out

19645

7705 SAR-8 Installation Guide Page 105

Establishing Router Management Connections

To establish a console connection:

Step 1.

Connect the terminal to the Console port on the front panel ( Figure 26 ) using the

serial cable.

Step 2.

Power on the terminal.

Step 3.

Establish the connection by pressing the <Enter> key a few times on your terminal keyboard.

Step 4.

At the router prompt, enter the login and password.

The default login is admin

.

The default password is admin

.

Telnet Connection

Telnet access provides the same options for user and administrator access as those available through the console port. You can access the router with a Telnet connection from a PC or workstation connected to the network once the following conditions are met:

• the router has successfully initialized

•

the Management port ( Figure 27 ) has been configured using the

bof>address command (see CLI Syntax )

CLI Syntax: bof address ip-address/mask [primary|secondary]

For more information about configuring router parameters, refer to the 7705 SAR OS Router

Configuration Guide. For pinout information, refer to

Management Port Pinouts on page

132

.

Figure 27: Management Port Connection

CSM

Management port

Stat Act

Pwr

Mgmt Port Console

Sync

In Out

19646

Page 106 7705 SAR-8 Installation Guide

Initializing and Provisioning

Running Telnet

After the IP parameters are configured, the CLI can be accessed with a Telnet connection.

To establish a Telnet connection, run a Telnet program and issue the Telnet command, followed by the IP address.

The following displays an example of a Telnet login:

C:\>telnet 192.168.1.xx1

Login: admin

Password: ########

ALU-1#

The default login is admin

.

The default password is admin

.

7705 SAR-8 Installation Guide Page 107

Provisioning CSM and Adapter Card Parameters

Provisioning CSM and Adapter Card Parameters

The CSM does not require provisioning. However, the IOM, which is a software module on the CSM, must be activated before any adapter cards and port parameters can be provisioned and configured. The IOM is activated using the card

and card-type

CLI commands to specify its slot number and card type. Adapter cards must be provisioned before their ports can be configured.

Notes:

• IOMs are specified using the card

and card-type

commands (items 1 and 2 in the list below).

• Adapter cards are provisioned and configured using the mda

and mda-type

commands

(items 3 and 4 in the list below).

Configure components in the following order:

1. Card slot number (use the card

command)

2. Card type

3. Adapter card slot number (use the mda

command)

4. Adapter card type

5. Ports

Card and Card-Type Commands

In the config

context, activate the IOM on the CSM using the card

and card-type

CLI commands to specify the IOM.

Note: For the 7705 SAR-8, when specifying the IOM, the slot number value is always 1 and the card type is always iom-1g.

Command

Step 1.

card slot-number

Step 2.

card-type card-type

Example card 1 card-type iom-1g

Page 108 7705 SAR-8 Installation Guide

Initializing and Provisioning

MDA and MDA-Type Commands for Adapter Cards

Note:

• In the config

context, adapter cards are identified by their mda-number , where the mda-number

is a number from 1 through 6. For example, an adapter card in slot MDA 4 is identified by mda-number 4.

• In the show

context, adapter cards are identified as “1/ n

”, where “1” is the slot number and “ n” is the mda-number . For example, the command show mda 1/5

displays information on the adapter card in slot MDA 5. For the 7705 SAR-8, the slot number is always 1.

• Adapter cards must be configured before their ports can be configured.

Adapter card slots with odd numbers are on the left side of the router (slots MDA 1, 3, and

5); adapter card slots with even numbers are on the right side (slots MDA 2, 4, and 6). See

Figure 5 on page 41

, which identifies the slots.

After the IOM is activated, continue in the config

context with the following CLI commands to provision the adapter card(s).

Command

Step 1.

mda mda-number

Step 2.

mda-type mda-type

Step 3.

exit

Example mda 1 mda-type a8-eth exit

To provision additional adapter cards, continue the configuration process with Step 4:

Step 4.

mda mda-number

Step 5.

mda-type mda-type

Step 6.

exit mda 3 mda-type a16-chds1 exit

7705 SAR-8 Installation Guide Page 109

Provisioning CSM and Adapter Card Parameters

Example

The following example displays the card

, card-type

, mda

and mda-type

commands to specify the IOM as an iom-1g type, with an 8-port Ethernet Adapter card in slot MDA 1 and a 16-port T1/E1 ASAP Adapter card in slot MDA 2:

ALU-1>config# card 1

ALU-1>config>card# card-type iom-1g

ALU-1>config>card# mda 1

ALU-1>config>card>mda# mda-type a8-eth

ALU-1>config>card>mda# exit

ALU-1>config>card# mda 2

ALU-1>config>card>mda# mda-type a16-chds1

ALU-1>config>card>mda# exit

The CLI display for the configuration example above looks similar to the following:

ALU-1>config# info

. . .

---------------------------------------------echo "Card Configuration"

#--------------------------------------------card 1

card-type iom-1g

mda 1

mda-type a8-eth

exit

mda 2

mda-type a16-chds1

exit exit

----------------------------------------------

ALU-1>config#

To configure ports, refer to the Card and Port Configuration section of the 7705 SAR OS

Interface Configuration Guide .

Page 110 7705 SAR-8 Installation Guide

Appendix A: Connectors and

LEDs

In This Chapter

This chapter provides information on the connectors and LEDs seen on the front of the

7705 SAR-8 . There are no connectors or LEDs on the back of the unit:

•

CSM Connectors and LEDs on page 112

•

Fan Module Connectors and LEDs on page 114

•

Adapter Card Connectors and LEDs on page 116

7705 SAR-8 Installation Guide Page 111

CSM Connectors and LEDs

CSM Connectors and LEDs

Figure 28

identifies the connectors and LEDs on the CSM.

Figure 28: CSM Connectors and LEDs

CSM

7 2 3

Stat Act

Pwr

1

4

Mgmt Port

5

Console

6

Sync

In Out

7

19647

Key

1

2

3

Table 26 describes the connectors and LEDs on the CSM.

Label/Part

Pwr

Stat (Status)

Act (Active)

Table 26: 7705 SAR-8 CSM Connector and LED Descriptions

Sub category

—

Description

—

—

Blue: Indicates that power to the CSM is on

Unlit: Indicates that there is no power to the CSM or the power is faulty

Green (solid): Indicates that the CSM is operationally up and administratively up

Green (blinking): Indicates that the CSM is initializing the system

Amber: Indicates that the CSM is operationally down but administratively up, or that hardware is booting up

Unlit: Indicates that the CSM is operationally down and administratively down

Green (solid): Indicates the active CSM

Green (blinking): Indicates the standby CSM

Page 112 7705 SAR-8 Installation Guide

Appendix A: Connectors and LEDs

Key

4

5

6

7

Table 26: 7705 SAR-8 CSM Connector and LED Descriptions (Continued)

Label/Part Sub category

Description

Mgmt Port Connector The Ethernet Management port is provisioned with an RJ-45 port and used for the initial system startup as well as system configuration and monitoring. It supports both half and full duplex modes, and 10M/100M or autonegotiated communication.

Refer to Management Port Pinouts on page 132

for pinout assignments.

LEDs

Link

Data

The Link LED is located in the top left corner of the port and the Data

LED is located in the top right corner.

Amber (blinking): Indicates that the Ethernet link has Rx/Tx activity

Unlit: Indicates that the Ethernet link has no activity, or is down or disabled

Green: Indicates that there is a valid communications link

Unlit: Indicates that there is no communications link, or that the link is operationally down or disabled or shut down

Note: The Data LED is not affected by a Lamp Test

Console — The console port is provisioned with a DB9 male connector and is used for the initial system startup as well as system configuration and monitoring.

The console port is a Universal Asynchronous Receiver/Transmitter

(UART) port. Refer to

Console Port Pinouts on page 133

for pinout assignments.

Use an EIA/TIA-232 DTE console cable to connect a terminal to the console port. The factory default baud rate is 115.2KBaud, and can be reconfigured for 9.6, 19.2, 38.4, or 57.6 KBaud.

Sync In

Ejector lever

Out

—

The “In” synchronization port is provisioned with a 1.0/2.3 coaxial connector that can be used to receive an external synchronization input signal.

The “Out” synchronization port is provisioned with a 1.0/2.3 coaxial connector that can be used to provide an external synchronization output signal.

The ejector levers help insert and remove the CSM from its card slot.

When rotated outward, the levers release the CSM connectors from the backplane.

7705 SAR-8 Installation Guide Page 113

Fan Module Connectors and LEDs

Fan Module Connectors and LEDs

Figure 29

identifies the connectors and LEDs on the Fan module.

Figure 29: Fan Module Connectors and LEDs

1

2

4

7705 SAR-8

FAN

Batt A

Batt B

Alarms

Critical

Major

Minor

ACO/LT

External

Alarms

3

5

FAN

19648

Key

1

2

Table 27 describes the connectors and LEDs on the Fan module.

Label/Part

FAN

Batt A

Batt B

Table 27: 7705 SAR-8 Fan Module Connector and LED Descriptions

Sub category

—

Description

—

Green: Indicates that the fans are operational.

Amber: Indicates that there is a fan failure.

Unlit : Indicates that the fan has power failure.

Note: The FAN LED is not affected by a Lamp Test.

Green: Indicates that DC input power is present and operational.

Unlit: Indicates that the DC power supply is not installed or the DC power feed is not connected.

Note: The Batt A and Batt B LEDs are not affected by a Lamp Test.

Page 114 7705 SAR-8 Installation Guide

Appendix A: Connectors and LEDs

Key

3

4

5

Table 27: 7705 SAR-8 Fan Module Connector and LED Descriptions (Continued)

Label/Part

Alarms

ACO/LT

External

Alarms

Sub category

Critical

Description

Major

Red: Indicates that a critical condition exists, such as a fan failure or a power feed failure.

Unlit: Indicates that there are no critical alarm conditions.

Red: Indicates that a serious condition exists, such as an overtemperature condition or a full compact flash device.

Unlit: Indicates that there are no major alarm conditions.

Minor Amber: Indicates that a condition exists, such as a card removal or a synchronization reference failure.

Unlit: Indicates that there are no minor alarm conditions.

The Audible Alarm Cutoff/Lamp Test button has two functions.

When pressed, the Lamp Test is enabled and the following LED activity occurs: all activity and status LEDs on the chassis glow green; all port

LEDs on T1/E1 ASAP Adapter cards glow green; critical and major

Alarm LEDs glow red and the minor Alarm LED glows amber.

Note: The following LEDS are not affected by the Lamp Test:

Management port LEDs on the CSM; Fan and Battery A/B LEDs on the

Fan module; and all port LEDs on the Ethernet Adapter card.

When released, all LEDs on CSM(s) and MDAs return to their pre-Lamp

Test state. The Alarm LEDs become unlit until the next new alarm condition.

Connector The External Alarms port is a DB15 serial port. It can receive input signals from four external alarm devices and provide output signals through three sets of contacts. Refer to

External Alarms Port Pinouts on page 135

for pinout assignments.

7705 SAR-8 Installation Guide Page 115

Adapter Card Connectors and LEDs

Adapter Card Connectors and LEDs

Adapter card connectors and LEDs are described in the specific adapter card installation guide.

Page 116 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable

Units

In This Chapter

This chapter provides information about field-replaceable units (FRUs) in the 7705 SAR-8 chassis:

•

Warnings and Notes on page 118

•

Replacing a CSM on page 119

•

Replacing Adapter Cards on page 122

•

Replacing the Fan Module on page 127

•

Installing a Slot Cover on page 130

7705 SAR-8 Installation Guide Page 117

Warnings and Notes

Warnings and Notes

Danger:

• Only trained and qualified personnel should install or replace this equipment.

• Use of procedures other than those specified in this Installation Guide can result in hazardous radiation exposure.

Warning:

• Electrostatic discharge (ESD) damage can occur if 7705 SAR-8 components are mishandled. Always wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is connected to site grounding point (typically, the grounding stud on the

7705 SAR-8, or a properly grounded rack or work bench).

• If power cables are connected to a circuit panel, always use caution when removing and replacing field-replaceable components.

• Always place router components on an anti-static surface.

• Slot covers are required in all empty slots to prevent excess dust accumulation and to help control airflow and electromagnetic interference.

Note: Unless stated otherwise in this installation guide, replacing an FRU requires modifying the configuration of the FRU before the FRU can be removed. Typically, this means using the shutdown

command to put the element(s) in an administratively “down” status.

Page 118 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable Units

Replacing a CSM

This section contains:

•

Warnings and Notes

•

Removing a CSM

•

Replacing a CSM

Warnings and Notes

Warning:

• Electrostatic discharge (ESD) damage can occur if 7705 SAR-8 components are mishandled. Always wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is connected to site grounding point (typically, the grounding stud on the

7705 SAR-8, or a properly grounded rack or work bench).

• Always place router components on an anti-static surface.

• Slot covers are required in all empty slots to prevent excess dust accumulation and to help control airflow and electromagnetic interference.

Note:

• When replacing CSMs, modifying the configuration is not required.

• The 7705 SAR-8 requires at least one CSM, which must be installed in slot CSM A. For redundancy, install a second CSM in slot CSM B.

• Do not force an adapter card into a CSM slot.

• Do not force a CSM into an adapter card slot.

• When removing a CSM, always use the ejector levers to make sure that the connector pins disconnect from the backplane.

• In a single CSM system, removing the active CSM causes the system to shut down. If you are not immediately installing a replacement CSM, cover the empty slot with a slot cover and power off the system until the CSM is replaced.

7705 SAR-8 Installation Guide Page 119

Replacing a CSM

Removing a CSM

Tools required:

• Phillips screwdriver

To remove a CSM:

Step 1.

Disconnect all cable connections to the CSM.

Step 2.

Use a Phillips screwdriver to loosen the captive screws that fasten the CSM to the chassis.

Step 3.

Simultaneously rotate the ejector levers outward to unseat the backplane connectors.

Step 4.

Pull the CSM out of the slot using the ejector levers. Place the CSM on an anti-static surface.

Step 5.

If you are not replacing the CSM immediately, install a slot cover to cover the empty

slot. Refer to Installing a Slot Cover on page 130 for instructions.

Replacing a CSM

Note: Each CSM has two ejector levers that release the card from the backplane connectors. During installation, the ejector levers must be rotated inward. The ejector levers must remain in the inward position while the card is installed in the chassis.

Figure 30

illustrates replacing a CSM.

Figure 30: Replacing a CSM

CSM

Stat Act

Pwr

Mgmnt Port

Console

SLOT ID

CSM A

MDA 1

MDA 3

CSM B

MDA 2

MDA 5

MDA 4

MDA 6

Sync

In

Out

CSM

Stat Act

Pwr

Sync

In Out

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19603

Tools required:

• torque driver for Phillips screws

Page 120 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable Units

To replace a CSM:

Step 1.

Remove the old CSM from the chassis.

Step 2.

Remove the new CSM from the packaging. Do not touch the printed circuit board or connector pins.

Step 3.

Install the replacement CSM. With the ejector levers rotated inward, hold the CSM by the levers, align the card with the slot guides and slide the card into the slot until the connectors are seated in the backplane and the faceplate is flush with the front of the chassis.

Warning: Do not force a CSM into its slot if its connector pins to not mate smoothly with the backplane connectors. The card may not be seated properly and the pins can get damaged. Pull the card half way out and then reinsert it.

Step 4.

Secure the card in place by tightening the captive screws. Do not over-tighten. The recommended torque is 4-6 lbf.-in.

7705 SAR-8 Installation Guide Page 121

Replacing Adapter Cards

Replacing Adapter Cards

This section contains:

•

Warnings and Notes

•

Changing the Adapter Card Configuration

•

Removing an Adapter Card

•

Replacing an Adapter Card

Warnings and Notes

Danger:

• Electrostatic discharge (ESD) damage can occur if 7705 SAR-8 components are mishandled. Always wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is connected to site grounding point (typically, the grounding stud on the

7705 SAR-8, or a properly grounded rack or work bench).

• Invisible laser radiation can be emitted from the aperture ports of an adapter card when no cable is connected. Avoid exposure and do not stare into open apertures.

Warning:

• Always place components on an anti-static surface.

• Do not power up a 7705 SAR-8 until all components are installed and their installation verified.

• Use only approved small form-factor pluggable (SFP) fiber-optic devices in adapter card ports.

• Slot covers are required in all empty slots to prevent excess dust accumulation and to help control airflow and electromagnetic interference.

Note:

• Ports cannot be configured if the adapter card is not provisioned.

• Services cannot be configured if ports are not configured.

• Adapter card slots are numbered MDA 1 through 6.

• Adapter cards and their slots are identified on the CLI as mda

slots.

• When you remove an adapter card, always use the ejector levers to ensure that the connector pins disconnect from the backplane.

Page 122 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable Units

Changing the Adapter Card Configuration

If you replace an adapter card with a different type, you must change the configuration to reflect the new adapter card type prior to removing the installed card. Each active port must be shut down before you shut down and remove an adapter card configuration. If you replace an adapter card with the same type, no configuration change is necessary. Refer to the 7705

SAR OS Interface Configuration Guide for details on configuring cards and ports.

Issue the following commands in the config

context to shut down ports, remove the adapter card from the configuration, and change to an 8-port Ethernet Adapter card:

Command

Step 1.

port port-id *

Example port 1/1/5

Step 2.

shutdown shutdown

*NOTE: The port>shutdown

command must be repeated for all enabled ports on the adapter card.

Step 3.

exit

Step 4.

card slot-number

Step 5.

mda mda-slot

Step 6.

shutdown exit card 1 mda 1 shutdown

Step 7.

exit

Step 8.

no mda mda-slot exit no mda 1

Step 9.

mda mda-slot mda

Step 10.

mda-type mda-type

Step 11.

no shutdown

Step 12.

exit mda a8-eth no shutdown exit

7705 SAR-8 Installation Guide Page 123

Replacing Adapter Cards

Removing an Adapter Card

Figure 31

illustrates removing an adapter card.

Figure 31: Removing an Adapter Card

1

2

MDA 1

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

A16-CND31

Stat

Act

Pwr

Port

Ports 1-16

3

4

Fan

Batt A

Batt B

7705 SAR-8

Alarm

Critical

Major

Minor

External

Alarms

FAN

4

3

3

4

Key

1

2

Table 28: Adapter Card Installation Features

Description

Card guide

Threaded receptacle

Captive screws

Ejector lever

Tools required:

• Phillips screwdriver

19649

Page 124 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable Units

To remove an adapter card:

Step 1.

If you are replacing an adapter card with a different type, change the configuration to reflect the new adapter card type. See

Changing the Adapter Card Configuration on page 123

.

Step 2.

Disconnect all cables from the adapter card ports.

Step 3.

Use a Phillips screwdriver to loosen the adapter card captive screws.

Note: The adapter card cannot be removed if the captive screws are tightened.

Step 4.

Simultaneously rotate the ejector levers outward to release the adapter card connectors from the backplane receptacles.

Step 5.

Grip the adapter card by the ejector levers and slide the card out of the slot. Place the adapter card on an anti-static surface.

Step 6.

If you are not replacing the adapter card immediately, cover the adapter card slot with a slot cover. See

Installing a Slot Cover on page 130

for instructions on installing a slot cover.

Replacing an Adapter Card

Figure 32

illustrates the replacement of an adapter card. Table 28 on page 124 identifies the

installation features.

Figure 32: Replacing an Adapter Card

SLOT ID

CSM A

MDA 1

MDA 3

CSM B

MDA 2

MDA 5

MDA 4

MDA 6

A16-CND31

Stat Act

Pwr Port

Ports 1-16

Fan

Batt A

Batt B

7705 SAR

Alarm

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19650

Tools required:

• torque driver for Phillips screws

7705 SAR-8 Installation Guide Page 125

Replacing Adapter Cards

To replace an adapter card:

Step 1.

Remove the replacement adapter card from the packaging and place on a flat antistatic work surface. Avoid touching board components and connector pins.

Step 2.

With the ejector levers rotated inwards, hold the adapter card by the levers, align the card with the slot guides, and slide the adapter card into the slot.

Step 3.

Press the adapter card firmly into the slot. Make sure that the card connectors are seated in the backplane connectors.

Step 4.

Secure the card in place by tightening the captive screws. Do not over-tighten. The recommended torque is 4-6 lbf.-in.

Step 5.

Check the Power LED on the adapter card faceplate. If the chassis is powered ON , the Power LED on the adapter card is lit (blue). Refer to the adapter card installation guide for information on LEDs for the specific adapter card.

Step 6.

Reconnect all previoulsy removed network cables to the adapter card ports.

Page 126 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable Units

Replacing the Fan Module

This section contains:

•

Warnings and Notes

•

Removing the Fan Module

•

Replacing the Fan Module

Warnings and Notes

Warning:

• Always keep your fingers away from rotating fan blades.

• The Fan module is hot-swappable. The 7750 SAR chassis operates safely for up to four minutes while you replace the Fan module. If a longer maintenance time is required, power off the system to prevent over-temperature conditions.

Note: In the event of a single fan failure, the remaining fans continue to run. This is sufficient to continue to provide adequate cooling for the system but the Fan module needs to be replaced as soon as possible. The individual fans are not field-replaceable.

7705 SAR-8 Installation Guide Page 127

Replacing the Fan Module

Removing the Fan Module

Figure 33

illustrates removing the Fan module.

Figure 33: Removing the Fan Module

SLOT ID

MDA 1

MDA 3

CSM B

MDA 2

MDA 5

MDA 4

MDA 6

Fan

Batt A

Batt B

7705 SAR-8

Alarms

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19651

Tools required:

• Phillips screwdriver

To remove the Fan module:

Step 1.

Unpack the replacement Fan module from the protective packaging. Place the Fan module on an anti-static surface.

Step 2.

Use a Phillips screwdriver to loosen the captive screw on the Fan module faceplate.

Step 3.

Pull the Fan module halfway out of the chassis and allow the fans to stop spinning.

Caution: DO NOT put your fingers or any tool in the Fan module if the fans are still spinning.

Wait until the fans stop spinning (about 20 seconds) before completely removing the Fan module from its slot.

Step 4.

When the fans stop spinning, pull the Fan module completely out of the slot.

Page 128 7705 SAR-8 Installation Guide

Appendix B: Field-Replaceable Units

Replacing the Fan Module

Figure 33

illustrates replacing the Fan module.

Figure 34: Replacing the Fan Module

SLOT ID

CSM A

MDA 1

CSM B

MDA 3

MDA 5

MDA 2

MDA 4

MDA 6

Fan

Batt A

Batt B

7705 SAR-8

Alarms

Critical

Major

Minor

ACO/LT

External

Alarms

FAN

19652

Tools required:

• torque driver for Phillips screws

To replace the Fan module:

Step 1.

Hold the replacement Fan module by its edges, align it with the slot guides, and slide it into the slot.

Step 2.

Press the Fan module firmly into the slot. Make sure that the Fan module connectors are seated in the backplane connectors.

Step 3.

Secure the Fan module by tightening the captive screw. Do not over-tighten. The recommended torque is 4-6 lbf.-in.

Step 4.

Verify that the Batt A and/or Batt B LEDs on the Fan module faceplate are lit. When lit (green), the system is receiving power from power feeds A and/or B. At least one of the Batt LEDs must be lit. Refer to

Fan Module Connectors and LEDs on page 114

for more information on Fan module LEDs.

7705 SAR-8 Installation Guide Page 129

Installing a Slot Cover

Installing a Slot Cover

A slot cover must be installed in all empty chassis slots.

Tools required:

• slot screwdriver

To install a slot cover:

Step 1.

Align the slot cover and insert the cover into the chassis slot.

Step 2.

Tighten the two captive screws that fasten the slot cover to the chassis. Do not overtighten. Slot covers do not have backplane connectors.

Page 130 7705 SAR-8 Installation Guide

Appendix C: Pinout Assignments

In This Chapter

This chapter provides information about the pinout assignments for the port connectors on the 7705 SAR-8:

•

CSM Ports on page 132

→

Management Port on page 132

→

Management Port Pinouts on page 132

→

Console Port on page 133

→

Console Port Pinouts on page 133

•

Fan Module Port on page 134

→

External Alarms Port on page 134

→

External Alarms Port Pinouts on page 135

→

Alarm examples on page 136

•

Adapter Card Ports on page 136

7705 SAR-8 Installation Guide Page 131

CSM Ports

CSM Ports

The CSM has two ports: the (Ethernet) Management port and the Console port.

Figure 35

identifies these ports.

Figure 35: CSM Ports

CSM

Management port

Console port

Stat Act

Pwr

Mgmt Port Console

Sync

In Out

19653

Management Port

The Management port supports half and full duplex communication via 10/100 or autonegotiated Ethernet. The Management port provides a channel to download software and configuration images and manage the system. This port is provisioned with an RJ45 connector on the front panel. You must provide a CAT5 Ethernet cable to connect to the port.

Management Port Pinouts

Table 29 displays the Management port pin assignments.

2

3

4

5

6

Pin

1

Table 29: Ethernet Management Port Pinouts — RJ45 Female

Signal

TX+

TX-

Direction

Output

Output

Description

Differential transmit data

–

positive

Differential transmit data – negative

NC

NC

RX-

—

—

Input

Not connected

Not connected

Differential receive data – negative

Page 132 7705 SAR-8 Installation Guide

Appendix C: Pinout Assignments

Pin

7

8

Table 29: Ethernet Management Port Pinouts — RJ45 Female (Continued)

Signal

NC

NC

Direction

—

—

Description

Not connected

Not connected

Console Port

The Console port is a Universal Asynchronous Receiver/Transmitter (UART) port used to configure router and system parameters. It can also be used for monitoring purposes. The

Console port is enabled by default and is configured as DTE. The default baud rate is

115 200. This port has a DB9 male connector. Connect the Console port to a terminal using an EIA/TIA-232 serial cable.

Console Port Pinouts

Table 30 displays the Console port pin assignments. The Console port is configured for DTE

mode.

6

7

4

5

8

9

2

3

Pin

1

Signal

DCD

RXD

TXD

DTR

GND

DSR

RTS

CTS

RI

Table 30: Console Port Pinouts — DB9 Male

Direction

Input

Input

Output

Output

Signal ground

Input

Output

Input

Input

Description

Data carrier detect

Receive data

Transmit data

Data terminal ready

Signal ground

Data set ready

Request to send

Clear to send

Ring indicator

7705 SAR-8 Installation Guide Page 133

Fan Module Port

Fan Module Port

Figure 36

identifies the connector for the External Alarms port on the Fan module.

Figure 36: Fan Module Port

7705 SAR-8

FAN

Batt A

Batt B

Alarms

Critical

Major

Minor

ACO/LT

External

Alarms

External Alarms port

FAN

19654

External Alarms Port

The External Alarms port provides access to three pairs of alarm output contacts and four alarm inputs. All alarm interfaces are rated for 5 VDC and 100 mA (source or sink). Each alarm input has a fixed severity associated with it — there is one Critical alarm input, two

Major alarm inputs, and one Minor alarm input (see Table 31

). State transitions on the inputs are debounced for 2 seconds.

You can display the status of the alarm inputs using the show chassis environment

CLI command.

The port uses a DB15 connector. You must provide an appropriate cable configured according to your alarm panel.

Page 134 7705 SAR-8 Installation Guide

Appendix C: Pinout Assignments

External Alarms Port Pinouts

Table 31 specifies the External Alarms port connector pinouts.

11

12

13

14

15

7

8

9

10

5

6

3

4

Pin

1

2

Table 31: External Alarms Port Pinouts

Signal

Alarm 1

Alarm 2 nc

Alarm output 3, pin 2

Alarm output 3, pin 1 nc

Ground nc

Alarm output 2, pin 2

Alarm output 2, pin 1

Alarm 3

Alarm 4 nc

Alarm output 1, pin 2

Alarm output 1, pin 1

Direction

Input

Input

—

Output

Output

—

Reference

—

Output

Output

Input

Input

—

Output

Output

Description

Critical alarm severity (fixed)

Major alarm severity (fixed)

Not connected

Contact opens on minor alarm

Contact opens on minor alarm

Not connected

Reference output for alarm inputs

Not connected

Contact opens on major alarm

Contact opens on major alarm

Major alarm severity (fixed)

Minor alarm severity (fixed)

Not connected

Contact closes on critical alarm

Contact closes on critical alarm

7705 SAR-8 Installation Guide Page 135

Adapter Card Ports

Alarm examples

Table 32 lists critical, major, and minor alarm examples.

Alarm Severity

Critical

Major

Minor

Table 32: Alarm Examples

Examples

• one or more fans have failed

• a power feed has failed

• a critical external alarm has been detected

• one or more adapter or CSM cards has reported an overtemperature condition

• a major external alarm has been detected

• a minor external alarm has been detected

Adapter Card Ports

Refer to the appropriate adapter card installation guide for port and pinout information on a specific adapter card.

Page 136 7705 SAR-8 Installation Guide

Standards and Protocol Support

Standards Compliance

IEEE 802.1p/q VLAN Tagging

IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTX

IEEE 802.3x Flow Control

IEEE 802.3z 1000BaseSX/LX

Protocol Support

LDP

RFC 5036 LDP Specification

MPLS

RFC 3031 MPLS Architecture

RFC 3032 MPLS Label Stack Encoding

RFC 4379 Detecting Multi-Protocol Label

Switched (MPLS) Data Plane Failures

DIFFERENTIATED SERVICES

RFC 2474 Definition of the DS Field in the IPv4 and IPv6 Headers

RFC 2597 Assured Forwarding PHB Group

RFC 2598 An Expedited Forwarding PHB

RFC 3140 Per-Hop Behavior Identification Codes

TCP/IP

RFC 768 UDP

RFC 791 IP

RFC 792 ICMP

RFC 793 TCP

RFC 826 ARP

RFC 854 Telnet

RFC 1350 The TFTP Protocol (Rev. 2)

RFC 1812 Requirements for IPv4 Routers

PPP

RFC 1332 PPP IPCP

RFC 1661 PPP

RFC 1989 PPP Link Quality Monitoring

RFC 1990 The PPP Multilink Protocol (MP)

ATM

RFC 2514 Definitions of Textual Conventions and

OBJECT_IDENTITIES for ATM

Management, February 1999

RFC 2515 Definition of Managed Objects for ATM

Management, February 1999 af-tm-0121.000 Traffic Management Specification

Version 4.1, March 1999

ITU-T Recommendation I.610 - B-ISDN Operation and Maintenance Principles and Functions version

11/95

ITU-T Recommendation I.432.1 - B-ISDN usernetwork interface - Physical layer specification:

General characteristics

GR-1248-CORE - Generic Requirements for

Operations of ATM Network Elements (NEs). Issue

3 June 1996

GR-1113-CORE - Bellcore, Asynchronous Transfer

Mode (ATM) and ATM Adaptation Layer (AAL)

Protocols Generic Requirements, Issue 1, July 1994

PSEUDOWIRES

RFC 4385 Pseudowire Emulation Edge-to-Edge

(PWE3) Control Word for Use over an

MPLS PSN

RFC 4447 Pseudowire Setup and Maintenance

Using the Label Distribution Protocol

(LDP)

RFC 4448 Encapsulation Methods for Transport of

Ethernet over MPLS Networks

RFC 4717 Encapsulation Methods for Transport of

Asynchronous Transfer Mode (ATM) over MPLS Networks

7705 SAR-8 Installation Guide Page 137

Standards and Protocol Support

RFC 5086 Structure-Aware Time Division

Multiplexed (TDM) Circuit Emulation

Service over Packet Switched Network

(CESoPSN)

RFC 5085 Pseudowire Virtual Circuit Connectivity

Verification (VCCV): A Control

Channel for Pseudowires

RADIUS

RFC 2865 Remote Authentication Dial In User

Service

RFC 2866 RADIUS Accounting

SSH draft-ietf-secsh-architecture.txt SSH Protocol

Architecture draft-ietf-secsh-userauth.txt SSH Authentication

Protocol draft-ietf-secsh-transport.txt SSH Transport Layer

Protocol draft-ietf-secsh-connection.txt SSH Connection

Protocol draft-ietf-secsh- newmodes.txt SSH Transport Layer

Encryption Modes

TACACS+ draft-grant-tacacs-02.txt The TACACS+ Protocol

NETWORK MANAGEMENT

ITU-T X.721: Information technology- OSI-Structure of Management Information

ITU-T X.734: Information technology- OSI-Systems

Management: Event Report Management Function

M.3100/3120 Equipment and Connection Models

TMF 509/613 Network Connectivity Model

RFC 1157 SNMPv1

RFC 1907 SNMPv2-MIB

RFC 2011 IP-MIB

RFC 2012 TCP-MIB

RFC 2013 UDP-MIB

RFC 2138 RADIUS

RFC 2571 SNMP-FRAMEWORKMIB

RFC 2572 SNMP-MPD-MIB

RFC 2573 SNMP-TARGET-&-

NOTIFICATION-MIB

RFC 2574 SNMP-USER-BASED-SMMIB

RFC 2575 SNMP-VIEW-BASED ACM-

MIB

RFC 2576 SNMP-COMMUNITY-MIB

RFC 2665 EtherLike-MIB

RFC 2819 RMON-MIB

RFC 2863 IF-MIB

RFC 2864 INVERTED-STACK-MIB

RFC 3014 NOTIFICATION-LOG MIB

RFC 3273 HCRMON-MIB

RFC 3411 An Architecture for Describing Simple

Network Management Protocol (SNMP)

Management Frameworks

RFC 3412 Message Processing and Dispatching for the Simple Network Management

Protocol (SNMP)

RFC 3413 Simple Network Management Protocol

(SNMP) Applications

RFC 3414 User-based Security Model (USM) for version 3 of the Simple Network

Management Protocol (SNMPv3)

RFC 3418 SNMP MIB draft-ietf-disman-alarm-mib-04.txt

draft-ietf-mpls-ldp-mib-07.txt

IANA-IFType-MIB

Proprietary MIBs

TIMETRA-ATM-MIB.mib

TIMETRA-CAPABILITY-7705-V1.mib

TIMETRA-CFLOWD-MIB.mib

TIMETRA-CHASSIS-MIB.mib

TIMETRA-CLEAR-MIB.mib

TIMETRA-FILTER-MIB.mib

TIMETRA-GLOBAL-MIB.mib

TIMETRA-LDP-MIB.mib

TIMETRA-LOG-MIB.mib

TIMETRA-MPLS-MIB.mib

TIMETRA-OAM-TEST-MIB.mib

TIMETRA-PORT-MIB.mib

TIMETRA-PPP-MIB.mib

TIMETRA-QOS-MIB.mib

TIMETRA-ROUTE-POLICY-MIB.mib

TIMETRA-SAP-MIB.mib

TIMETRA-SDP-MIB.mib

TIMETRA-SECURITY-MIB.mib

TIMETRA-SERV-MIB.mib

TIMETRA-SYSTEM-MIB.mib

TIMETRA-TC-MIB.mib

Page 138 7705 SAR-8 Installation Guide

Numerics

16-port T1/E1 ASAP Adapter card cable connections

95

Ethernet and copper cables

96

fiber cables

97

changing the configuration

123

connectors

116

EMC compliance

98

installing

88

LEDs

116

operating requirements

57

ports

136

provisioning

MDA commands

109

parameters

108

removing

124

replacing

122, 125

shield ground connection

98

specifications

55

storage specifications

64

7705 SAR-8 components

40

adapter cards

42

chassis

40

CSM

41

fan module

44

installation process

49

power connectors

43

storage specifications

64

8-port Ethernet Adapter card cable connections

95

Ethernet and copper cables

96

fiber cables

97

changing the configuration

123

connectors

116

EMC compliance

98

installing

88

LEDs

116

operating requirements

57

ports

136

provisioning

7705 SAR-8 Installation Guide

Index

MDA commands

109

MDA-type commands

109

parameters

108

removing

124

replacing

122, 125

shield ground connection

98

specifications

55

storage specifications

64

A

adapter cards; See 16-port T1/E1 ASAP Adapter card, See 8-port Ethernet Adapter card

alarm examples

136

B backplane operating requirements

57

BNC Distribution panel

46

grounding

92

installing

92

C cables

CAT5 shielded cable

88, 132

CAT5E shielded cable

88

T1/E1

48

chassis

40

clearance requirements

60

DC power

78

connections

79

DC power harness

80

wiring

79

ground wiring

73

ground wire description

74

grounding making the ground connection

73

installation cabling

63

choosing a location

58

DC power requirements

63

grounding

61

Page 139

Index placement

61

unpacking

68

installing rack-mounting

70

location requirements

59

slot identification

41

specifications

54

storage specifications

64

compact flash directory structure

104

file descriptions

104

components installing

84

connections console

105

Telnet

106

connector descriptions adapter cards

116

CSM

112

fan module

114

console port pinouts

133

critical alarm examples

136

CSM

41, 84

compact flash

84

connectors

112

EMC compliance

85, 98

external synchronization connections

99

faceplate

41

installing

84

IOM module provisioning

108

LEDs

112

operating requirements

57

ports

132

console port

133

console port pinouts

133

management port

132

management port pinouts

132

redundant configurations

86

removing

120

replacing

119, 120

shield ground connection

98

simplex configurations

86

specifications

56

storage specifications

64

D

DB9 male port pinouts

133

DC inputs

79

DC power harness

80

operating requirements

57

DC power LEDs

44

DC-input power connections

79

distribution panels; See BNC Distribution panel,

See RJ45 Distribution Panel

D-Sub 2W2 connectors

79, 80

E

EMC compliance

98

environmental specifications

54

Ethernet management port pinouts

132

external alarms port pinouts

135

external synchronization source input connections

100

source output connections

100

F fan module

44, 86

airflow

64

alarm interface

86

connectors

114

EMC compliance

86, 98

external alarms port

134

external alarms port pinouts

135

installing

86

LEDs

45, 114

monitoring temperature

45

operating requirements

57

operation

44

removing

128

replacing

127, 129

safety

64

shield ground connection

98

specifications

56

storage specifications

64

fan operation

44

field-replaceable units; see FRUs

FRUs adapter cards

122

CSM

119

fan module

127

Page 140 7705 SAR-8 Installation Guide

slot cover

130

storage specifications

64

G grounding ground connection

73

grounding the chassis

73

I initializing the system

102

troubleshooting

103

installation chassis location requirements

59

installing

7705 SAR-8 chassis

70

components

84

adapter cards

88

CSM

84

fan module

86

fan trays

128

SFPs

90

IOM card commands

108

card type commands

108

configuring components

108

provisioning

108

L

LED descriptions adapter cards

116

CSM

112

fan module

114

M major alarm examples

136

minor alarm examples

136

monitoring temperature

45

P power connections

79

consumption by component

56

power system

43

provisioning adapter card parameters

108

7705 SAR-8 Installation Guide

Index

CSM IOM module

108

R redundant configurations

86

RJ45 Distribution panel

47

grounding

92

installing

92

RJ45 female port pinouts

132

router initializing

102

powering up

102

troubleshooting initial startup

103

router management

105

console connection console port

105

default settings

105

establishing

105

Telnet connection access conditions

106

login

107

management port

106

running Telnet

107

S safety

61

cabling

63

fan module

64

grounding

61

placement

61

power

63

DC power requirements

64

SFPs

90

installing

90

simplex configurations

86

site preparation compliance

65

slot cover

43

installing

130

storage specifications

64

system specifications

54

adapter card specifications

55

chassis specifications

54

component operating requirements

57

CSM specifications

56

environmental specifications

54

Page 141

Index fan module specifications

56

power consumption

56

T

T1/E1 cables

48

temperature

45

troubleshooting system startup

103

U unpacking the chassis

68

Y

Y-cable

42, 99, 100

Page 142 7705 SAR-8 Installation Guide

Customer documentation and product support

Customer documentation

http://www.alcatel-lucent.com/osds

Product manuals and documentation updates are available through the Alcatel-Lucent Support

Documentation and Software Download service at alcatel-lucent.com. If you are a new user and require access to this service, please contact your Alcatel-Lucent sales representative.

Technical support

http://www.alcatel-lucent.com/support

Customer documentation feedback

[email protected]

© 2008 Alcatel-Lucent. All rights reserved.

3HE 03256 AAAA TQZZA Edition 01