Instruction manual

Thank you for purchasing this product.

Before using this product please read the instructions carefully.

After reading the instruction manual, please keep it for reference.

Caution

● Keep this product out of the reach of children under 3.

● Keep this product away from small children.

  Seek medical advice immediately if it is swallowed.

● Please be careful and not allow children to wrap 

  the cord around their neck.

● Keep the controller away from dusty or humid areas.

● Do not use this product if damage or alteration occurs.

● Do not get the product wet or leave it where it can get wet.

  It may cause an electric shock or defect.

● Do not leave the product around a heater, audio amp, etc.

  Do not leave it under direct sunlight  It may cause a defect.

● Do not touch the metal parts of the USB plug with your 

  finger or other metal material. It may cause injury or defect.

● Do not apply strong impact or weight on the product.

● Do not pull roughly or bend the cable of the controller.

● Never disassemble, repair or modify this product.

● If product needs cleaning, use only a soft dry cloth.

  Do not use any chemical agents like benzine or thinner.

● Do not use this product for anything other than its 

  intended purpose. 

  We are not responsible for any accidents or damages 

  in the event of use other than the intended purpose.

Included

Controller ：  × 1 Instruction manual ：  × 1

Platform

Nintendo Switch / PC(Xinput)

Supported OS

System requirements

Windows

®

10 ／ 8 〜 8.1

／ 7

USB Port, Internet Connection

Important

Please read the Nintendo Switch instructions carefully before you use this product with the Nintendo Switch console.

Make sure that your Nintendo SwitchTM is updated with the latest system software.

※ This product is not a wireless controller.

※ Please be aware that unexpected action may occur if the Turbo function is used in the HOME Menu.

Layout

Nintendo Switch

Left Stick

{ Left Stick Button (Hold) }

Right Stick

{ Right Stick Button (Hold) }

- Button

Controller cable

PC

Left Stick

{ Left Stick Button (Hold) }

Right Stick

{ Right Stick Button (Hold) }

BACK Button

Controller cable

Control Pad

B Button

TURBO LED

L Button

Control Pad

B Button

TURBO LED

LT Button

Capture Button

A Button

+ Button

ZL Button

There is no function

A Button

START Button

LB Button

How to connect

Please insert the USB connector of the controller into the USB port of the Nintendo Switch TM Dock.

※ Do not connect to anything other than a USB port. It may cause a defect.

TURBO Button

X Button

USB Connector

R Button

HOME Button

Y Button

ZR Button

TURBO Button

X Button

USB Connector

RT Button

GUIDE Button

Y Button

RB Button

L/R to ZL/ZR Toggle Function

Switch button functions between L/R and ZL/ZR buttons.

Connect it to the Nintendo Switch Dock USB port.

How to switch

TURBO LED will turn off.

L Button

ZL Button

R Button

ZR Button

+

Connect it to the Nintendo Switch Dock USB port.

Press and hold the ZL and ZR buttons simultaneously and connect the USB connector to the Nintendo Switch Dock USB port.

TURBO LED (RED) will turn on.

ZL Button

L Button

ZR Button

R Button

※ Settings will be saved even after you unplug the controller or turn off the power.

※ To reset the button settings, repeat the "How to switch" process.

※ Turning ON the Nintendo Switch while simultaneously pressing the ZL/ZR buttons with the USB connected will switch the button settings.

How to use the Turbo Functions

The Turbo hold function allows continuous rapid fire without having to hold the button.

(Pressing the assigned button deactivates this).

The following buttons can be set to Turbo or Turbo hold mode:

A Button / B Button / X Button / Y Button / L Button / R Button / ZL Button / ZR Button /

Control Pad (UP / DOWN / LEFT / RIGHT)

* Control Pad (UP, DOWN, LEFT or RIGHT) are not compatible with the Turbo hold mode,

    and can only be set to Turbo mode.

Setting method Turbo LED Status

Button ON Button OFF

Turbo Mode

TURBO Button

+

Hold down the Turbo button and then press the button that you want to set to Turbo mode.

TURBO LED will flash.

（ Green or Orange ）

Button ON

TURBO LED will turn on.

（ Green or Orange

Button OFF

）

Turbo Hold

+

TURBO Button

Press the button once more, and the button will remain inTurbo (Turbo Hold).

TURBO LED will turn on.

（ Green or Orange ）

TURBO LED will flash.

（ Green or Orange ）

Turbo OFF

+

TURBO Button

Pressing the button again once more will deactivate the Turbo function.

OFF

※ LED will turn red while L/R and ZL/ZR button

  functions are switched.

In the case that after deactivating the turbo  function, the turbo Indicator LED does not  turn off, this means that there is still a button  set to Turbo/Turbo Hold.

OFF

(All buttons)

+

TURBO Button Button

Hold the TURBO Button and press the SELECT Button.

OFF

※ LED will turn red while L/R and ZL/ZR button

  functions are switched.

If you forget which buttons you have set to 

Turbo mode, deactivate them all and reassign,  as you require.

* The Turbo LED will flash at a rate corresponding to the Turbo speed. The Turbo LED will flash as long as one of the button is in Turbo mode.

* By pressing the HOME Button, all Turbo function and Turbo hold settings will be deactivated.

When restarting game play, you will need to set the Turbo function again.

* Turbo Function may not be compatible with all software titles. Please try adjusting the Turbo settings or simply turn OFF TURBO.

* Turbo function will deactivate when you unplug the USB connector.

How to change Turbo Speed

You can adjust the Turbo mode to 3 different speeds.

While pressing the Turbo Button, push up on the Right Analog Stick to change the Turbo speed in the following order :

5 times/second → 10 times/second → 20 times/second

While pressing the Turbo Button, push down on the Right Analog Stick to change the Turbo speed in the following order :

20 times/second → 10 times/second → 5 times/second

* Turbo speed is set to 10 times/second by default.

* Right Stick must be returned to the neutral position before changing to the next turbo speed.

* The Turbo LED will flash at a rate corresponding to the Turbo speed for 2 seconds.

Main Features

■ External dimensions  :  (width) 103mm × (depth) 141mm × (height) 69mm

■ Cable length  :  (Overall length) Approximately 3 m  

■ Rating  :  5V   45mA

■ Weight  :  About 230g

+

+

● This product is not a wireless controller.

● This product is not equipped with vibration function.

● The image on the packaging may differ from the actual product.

● The manufacturer reserves the right to change the product design or specifications without notice.

● Nintendo Switch logo, Nintendo Switch are trademarks of Nintendo.

● HORI & HORI logo are registered trademarks of HORI.

Target age : 6 years and over