advertisement
Final page size: A5 (148mm x 210mm)
DCF680
DCF682
English (original instructions) 3
B
Copyright D e
WALT
Fig. A
DCF680
8
7
3
9
4
1
2
6
4
DCF682 3
7
8
Fig. B
11
12
5
6
6
5
10
5
1
1
Fig. E2
2
Fig. C
DCF680
Fig. D
8
2
9
1 3 5 7
10
Fig. E1
Fig. E3
English (original instructions)
English
7.2 V HEAVY-DUTY CORDLESS SCREWDRIVER
DCF680, DCF682
Congratulations!
You have chosen a D e WALT tool. Years of experience, thorough product development and innovation make D e WALT one of the most reliable partners for professional power tool users.
Technical Data
Battery pack
Battery Type
Voltage
Capacity
Weight
Voltage
Type
No-load speed
Battery type
Max. torque
Tool holder
Weight (without battery pack)
V
DC min -1
Nm mm kg
DCF680
7.2
1
0–430
Li-Ion
4.0
6.35 Hex
0.42
DCF682
7.2
1
0–430
Li-Ion
4.0
6.35 Hex
0.40
Charger
Mains voltage
Charging Time
Weight
EC-Declaration of Conformity
Machinery Directive
V
AC min kg
V
DC
A h kg
Noise values and/or vibration values (triax vector sum) according to
EN62841-2-2:
L
PA
(emission sound pressure level) dB(A) 60
L
WA
(sound power level)
K (uncertainty for the given sound level) dB(A) dB(A)
71
1.5
60
71
1.5
DCB080
Li-Ion
7.2
1
0.08
DCB095
230
60
0.02
Cordless Screwdriver
DCF680, DCF682
D e
WALT declares that these products described under Technical
Data are in compliance with:
2006/42/EC, EN62841-1:2015, EN62841-2-2:2014.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact D e WALT at the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of D e
WALT .
Screwdriving without impact
Vibration emission value a h
=
Uncertainty K = m/s 2 m/s 2
< 2.5
1.5
< 2.5
1.5
The vibration and/or noise emission level given in this information sheet has been measured in accordance with a standardised test given in EN62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
WARNING: The declared vibration and/or noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and/or noise emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/ or noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm (relevant for vibration), organisation of work patterns.
Markus Rompel
Vice President of Engineering, PTE-Europe
D e WALT , Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
12.08.2019
WARNING: To reduce the risk of injury, read the instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury .
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury .
3
Batteries
Chargers/Charge Times (Minutes)
Cat #
DC
Weight
4
English
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury .
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage .
Denotes risk of electric shock.
Denotes risk of fire.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
1) Work Area Safety
a ) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b ) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e ) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f ) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d ) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e ) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g ) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h ) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
A careless action can cause severe injury within a fraction of a second.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b ) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c ) Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h ) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the manufacturer.
A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
b ) Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire.
c ) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e ) Do not use a battery pack or tool that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
f ) Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130 °C may cause explosion.
g ) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
6) Service
a ) Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs.
Service of battery packs should only be performed by the manufacturer or authorized service providers.
English
Additional Safety Instructions for Cordless
Screwdrivers
• Wear ear protectors with screwdrivers. Exposure to noise can cause hearing loss.
• Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and shock the operator.
Residual Risks
The following risks are inherent to the use of drills:
• Injuries caused by touching the rotating parts or hot parts of the tool.
In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during operation.
• Risk of personal injury due to prolonged use.
Chargers
D e WALT chargers require no adjustment and are designed to be as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.
Your D e WALT charger is double insulated in accordance with EN60335; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced only by
D e
WALT or an authorised service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data ). The minimum conductor size is 1 mm 2 ; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
5
English
6
Important Safety Instructions for All Battery
Chargers
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for compatible battery chargers (refer to Technical Data ).
• Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.
WARNING: We recommend the use of a residual current device with a residual current rating of 30mA or less.
CAUTION: Burn hazard. To reduce the risk of injury, charge only D e WALT rechargeable batteries. Other types of batteries may burst causing personal injury and damage.
CAUTION: Children should be supervised to ensure that they do not play with the appliance.
NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean
• DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.
• These chargers are not intended for any uses other than charging D e WALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.
• Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire,electric shock, or electrocution.
• Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
• Do not operate charger with damaged cord or plug— have them replaced immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way.
Take it to an authorised service centre.
• Do not disassemble charger; take it to an authorised service centre when service or repair is required.
Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
• In case of damaged power supply cord the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard.
• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
• NEVER attempt to connect two chargers together.
• The charger is designed to operate on standard
230V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.
Charging a Battery (Fig. B)
1. Plug the charger 11 into an appropriate outlet before inserting battery pack.
2. Insert the battery pack 6 into the charger. Ensure that the battery is positioned so the release button 5 is on the same side as charging light 12 . The red (charging) light 12 will blink continuously indicating that the charging process has started.
3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger.
nOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully before first use.
nOTE: During the presence of an electrostatic discharge (ESD) pulse, the charger function is interrupted, but resumes without operator intervention when the ESD pulse is removed.
Charger Operation
Refer to the indicators below for the charge status of the battery pack.
Charge Indicators
Charging
Fully Charged
Hot/Cold Pack Delay*
* The red light will continue to blink, but a yellow indicator light will be illuminated during this operation. Once the battery pack has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to light.
nOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery pack to be tested at an authorised service centre.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the
pack charging mode. This feature ensures maximum battery pack life.
A cold battery pack will charge at a slower rate than a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery pack warms.
Electronic Protection system
XR Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium-ion battery pack on the charger until it is fully charged.
Wall Mounting
These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 25.4 mm long with a screw head diameter of 7–9 mm, screwed into wood to an optimal depth leaving approximately 5.5 mm of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning . Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
Battery Packs
Important Safety Instructions for All Battery
Packs
When ordering replacement battery packs, be sure to include catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.
• Never force battery pack into charger. Do not modify battery pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious personal injury.
• Charge the battery packs only in D e WALT chargers.
• DO NOT splash or immerse in water or other liquids.
English
• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed
40 ˚C (104 ˚F) (such as outside sheds or metal buildings in summer).
• Do not incinerate the battery pack even if it is severely damaged or is completely worn out.
The battery pack can explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs are burned.
• If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.
WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to service centre for recycling.
WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.
CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.
Transportation
WARNING: Fire hazard. Transporting batteries can possibly cause fire if the battery terminals inadvertently come in contact with conductive materials. When transporting batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.
NOTE: Lithium-ion batteries should not be put in checked baggage.
D e
WALT batteries comply with all applicable shipping regulations as prescribed by industry and legal standards which include UN Recommendations on the Transport of Dangerous
Goods; International Air Transport Association (IATA) Dangerous
Goods Regulations, International Maritime Dangerous Goods
(IMDG) Regulations, and the European Agreement Concerning
The International Carriage of Dangerous Goods by Road (ADR).
Lithium-ion cells and batteries have been tested to section 38.3
7
8
English of the UN Recommendations on the Transport of Dangerous
Goods Manual of Tests and Criteria.
In most instances, shipping a D e
WALT battery pack will be excepted from being classified as a fully regulated Class 9
Hazardous Material. In general, only shipments containing a lithium-ion battery with an energy rating greater than 100 Watt
Hours (Wh) will require being shipped as fully regulated Class 9.
All lithium-ion batteries have the Watt Hour rating marked on the pack. Furthermore, due to regulation complexities, D e WALT does not recommend air shipping lithium-ion battery packs alone regardless of Watt Hour rating. Shipments of tools with batteries (combo kits) can be air shipped as excepted if the Watt
Hour rating of the battery pack is no greater than 100 Whr.
Regardless of whether a shipment is considered excepted or fully regulated, it is the shipper's responsibility to consult the latest regulations for packaging, labeling/marking and documentation requirements.
The information provided in this section of the manual is provided in good faith and believed to be accurate at the time the document was created. However, no warranty, expressed or implied, is given. It is the buyer’s responsibility to ensure that its activities comply with the applicable regulations.
Storage Recommendations
1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results.
nOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger and the battery pack may show the following pictographs:
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the environment.
Charge D e WALT battery packs only with designated
D e
WALT chargers. Charging battery packs other than the designated D e WALT batteries with a D e WALT charger may make them burst or lead to other dangerous situations.
Do not incinerate the battery pack.
Battery Type
The DCF680 and DCF682 operate on a 7.2 volt battery pack.
These battery packs may be used: DCB080. Refer to Technical
Data for more information.
Package Contents
The package contains:
1 Cordless Screwdriver
1 Charger
1 Battery pack (G1 model)
2 Battery packs (G2 model)
1 Kitbag (G1 model)
1 Kitbox (G2 model)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced immediately.
Visible radiation. Do not stare into light.
Date Code Position (Fig. B)
The date code, which also includes the year of manufacture, is printed into the housing surface that forms the mounting joint between tool and battery.
Example:
2019 XX XX
Year of Manufacture
1
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Motion control activation trigger
2
3
4
5
Lock off switch
LED worklight
Battery fuel gauge
Battery release button
6
7
Battery pack
Quick release chuck
Chuck collar 8
9
10
Torque adjustment collar (DCF680 Only)
Release button (DCF680 Only)
Intended Use
These screwdrivers have been designed for professional screwdriving applications.
DO nOT use under wet conditions or in the presence of flammable liquids or gases.
These screwdrivers are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use this tool.
• Young children and the infirm.
This appliance is not intended for use by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.
WARNING: Use only D e
WALT battery packs and chargers.
Inserting and Removing the Battery Pack from the Tool (Fig. B)
nOTE: Make sure your battery pack 6 is fully charged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 6 with the rails inside the tool’s handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 5 and firmly pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the charger section of this manual.
English
Fuel Gauge Battery Packs (Fig. A, B)
Some D e WALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the motion control activation trigger 1 . A combination of the three green LED lights will illuminate designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application.
Quick Release Chuck (Fig. A, D)
nOTE: The chuck accepts 6.35 mm hex accessories only.
To install a bit, insert the bit into the chuck until the clip locks it in place.
To remove a bit, pull the chuck collar 8 forward. Remove the bit and release the collar.
Two Position Screwdriver (Fig. C)
DCF680
To convert the tool to an angled screwdriver press the release button 10 and rotate the top portion of the tool as shown in
Figure C.
NOTICE: Do not use screwdriver as a pry bar in either position.
CAUTION: To avoid screwdriver being turned on accidentally, put the lock off switch 2 in the up, lockedoff, position.
Torque Adjustment Collar (Fig. A, C)
DCF680
The torque adjustment collar 9 is marked with numbers and a
MAX symbol. To set the torque align the desired setting with the arrow on the tool housing. The higher the number on the collar, the higher the torque. To lock the clutch for heavy fastening operations, move to the MAX position. Failure to do this will allow the clutch to slip while attempting to fasten.
Prior to Operation
• Make sure your battery pack is (fully) charged.
• Insert the appropriate bit.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and applicable regulations.
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.
9
10
English
Proper Hand Position (Fig. E1–E3)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.
DCF680
Proper hand position requires one hand on the main handle as shown in Figure E1.
WARNING: If the tool will be used in elongate position and highest MR please hold tool with both hands as shown in Figure E2.
DCF682
Proper hand position requires two hand on the tool as shown in Figure E3.
Screwdriving (Fig. A, E)
Your screwdriver uses gyroscopic technology to sense your hand motion. To operate, press in the motion control activation trigger and turn your hand in the direction that you want the screwdriver to operate.
Setting Initial Starting Point
1. Grasp the screwdriver as shown in Figure E.
2. Press and hold in the motion control activation trigger.
3. When the LED illuminates the tool is ready for use.
4. To reset initial starting point first release the motion control activation trigger. Move tool to new position, then press and hold in the motion control activation trigger.
Operating in Forward Direction
1. Grasp the screwdriver as shown in Figure E.
2. Engage head of fastener with screwdriver accessory on work piece. Follow instructions for setting initial starting point.
3. Rotate your hand clockwise and the screwdriver will activate in the forward direction.
Operating in Reverse Direction
1. Grasp the screwdriver as shown in Figure E.
2. Engage head of fastener with screwdriver accessory on work piece. Follow instructions for setting initial starting point.
3. Rotate your hand anti-clockwise and the screwdriver will activate in the reverse direction.
To turn the tool off, release the motion control activation trigger.
nOTE: When the tool is not in use or during transit please be sure to remove any accessory from the tool and activate trigger lock 2 .
Variable speed
• The spindle speed is dependent upon the speed that you rotate your hand.
• The slower you rotate your hand, the slower the screwdriver turns.
• The faster you rotate your hand, the faster the screwdriver turns.
• If you wish to increase the spindle speed, rotate your hand further in the same direction.
• If you wish to decrease the spindle speed, rotate your hand back towards the initial starting point.
MAINTENANCE
Your D e WALT power tool has been designed to operate over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories.
An accidental start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered by D e WALT , have not been tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D e WALT recommended accessories should be used with this product.
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com
.
Rechargeable Battery Pack
This long life battery pack must be replaced when it fails to produce sufficient power on jobs which were easily done before.
At the end of its technical life, discard it with due care for our environment:
• Run the battery pack down completely, then remove it from the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.
English
11
12
13
Belgique et
Luxembourg België en Luxemburg
Danmark
Deutschland
Ελλάς
España
France
Schweiz
Suisse
Svizzera
Ireland
Italia
Nederlands
Norge
Österreich
Portugal
Suomi
Sverige
Türkiye
United Kingdom
Australia
Middle East Africa
D e
WALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
D e WALT ( Stanley Black&Decker AS)
Roskildevej 22
2620 Albertslund
D e WALT
Richard Klinger Str. 11
65510 Idstein
D e
WALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος
D e WALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
D e
WALT (Stanley Black & Decker France SAS)
62 Chemin de la Bruyère
CS 60105,
69574 DARDILLY Cedex
D e
WALT
In der Luberzen 42
8902 Urdorf
D e
WALT
Building 4500, Kinsale Road
Cork Airport Business Park
Cork, Ireland
D e WALT via Energypark 6
20871 Vimercate (MB), IT
D e
WALT
Netherlands BVPostbus 83,
6120 AB BORN
D e
WALT
Postboks 4613
0405 Oslo, Norge
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
Tel:
Fax:
32 15 47 37 99
70 20 15 10
70 22 49 10
Tel: 06126-21-0
Fax: 06126-21-2770
Τηλ: 00302108981616
Φαξ: 00302108983570
Tel:
Fax:
Tel:
Fax:
Tel:
Fax:
934 797 400
934 797 419
04 72 20 39 20
04 72 20 39 00
044 - 755 60 70
044 - 730 70 67
Tel: 00353-2781800
Fax:
Tel:
Fax:
Tel:
Fax:
01278 1811
800-014353
39 039-9590200
Fax: 39 039-9590311
Tel: 31 164 283 063
31 164 283 200
45 25 13 00
45 25 08 00
D e WALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
D e WALT
Ed. D Dinis, Quina da Fonte
Rua dos Malhoes 2 2A 2º Esq.
Oeiras e S. Juliao da Barra, paço de Arcos e Caxias
2770 071 Paço de Arcos
Tel:
Fax:
Tel:
Fax:
01 - 66116 - 0
01 - 66116 - 614
+351 214667500
+351214667580
D e WALT
PL47
00521 Helsinki, Suomi
Puh:
Faksi:
010 400 4333
0800 411 340
D e
WALT
BOX 94
43122 Mölndal
Sverige
Tel:
Fax:
031 68 61 60
031 68 60 08
Sanayi ve Ticareet Bakanlığı tebliğince kullanim ömrü 7 yıldır.
Stanley Black & Decker Turkey Alet Üretim San. Tic. Ltd.Şti.
AND Kozyataği - İçerenköy Mah. Umut Sok. AND Ofis Sit. No: 10-12 / 82-83-84
Ataşehir/İstanbul, Türkiye
Tel: +90 216 665 2900
Faks: +90 216 665 2901
D e
WALT , 210 Bath Road;
Slough, Berks SL1 3YD
Tel: 01753-567055
Fax: 01753-572112
D e WALT
810 Whitehorse Road Box Hill
VIC 3128 Australia
D e
WALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
Tel:
Fax:
971 4 812 7400
971 4 2822765
N764114 www.dewalt.fi [email protected]
www.dewalt.se [email protected]
www.dewalt.com.tr
www.dewalt.co.uk [email protected]
www.dewalt.com.au www.dewalt.co.nz
www.dewalt.ae
www.dewalt.be [email protected]
www.dewalt.dk [email protected]
www.dewalt.de [email protected]
www.dewalt.gr
www.dewalt.es [email protected]
www.dewalt.fr [email protected]
www.dewalt.ch [email protected]
www.dewalt.ie
www.dewalt.it
www.dewalt.nl
www.dewalt.no [email protected]
www.dewalt.at [email protected]
www.dewalt.pt [email protected]
08/19
advertisement
Related manuals
advertisement