HP Color LaserJet CM6049f Multifunction Printer series User Guide
Advertisement
Advertisement
HP Color LaserJet CM6049f MFP
User Guide
HP Color LaserJet CM6049f MFP
User Guide
Copyright and License
© 2009 Copyright Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Part number: CE799-90904
Edition 2, 8/2019
Trademark Credits
Adobe ® , Acrobat ® , and PostScript ® are trademarks of Adobe Systems Incorporated.
Corel® is a trademark or registered trademark of Corel Corporation or Corel
Corporation Limited.
Microsoft ® , Windows ® , and Windows NT ® are U.S. registered trademarks of Microsoft
Corporation.
Windows Vista™ is either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
PANTONE® is Pantone, Inc's checkstandard trademark for color.
UNIX ® is a registered trademark of The Open
Group.
ENERGY STAR ® and the ENERGY STAR logo ® are U.S. registered marks of the United
States Environmental Protection Agency.
Table of contents
ENWW iii
4 Use the product with Macintosh
Open the HP Printer Utility ............................................................... 73
HP Printer Utility features ................................................................. 73
Create and use printing presets in Macintosh ................................................... 75
Resize documents or print on a custom paper size .......................................... 75
Print multiple pages on one sheet of paper in Macintosh ................................. 76
Print on both sides of the page (duplex printing) ............................................... 77
iv ENWW
Dynamic Host Configuration Protocol (DHCP) ................................. 89
Subnet mask ..................................................................................... 89
Default gateway ................................................................................ 89
Load standard-sized media into trays 2, 3, 4, or 5 .......................................... 102
Load undetectable standard-sized media into Tray 2, 3, 4, and 5 .................. 104
Load custom-size media into tray 2, 3, 4, or 5 ................................................ 105
ENWW v
Select the operating mode at the control panel ............................................... 118
Select the operating mode in the printer driver ............................................... 118
Select the operating mode in the printer driver (Mac OS X) ........................... 118
Print the remaining copies of a proof and hold job .......................................... 128
vi ENWW
Restrict color printing and copying from the control panel .............................. 145
ENWW vii
CMYK ink set emulation (HP postscript level 3 emulation) ............................. 149
Add e-mail addresses to the local address book ............................................ 167
Delete e-mail addresses from the local address book .................................... 167
viii ENWW
14 Manage and maintain the product
Open the embedded Web server by using a network connection ................................... 178
Enable memory for Windows 2000 and XP .................................... 198
Install an HP Jetdirect or EIO print server card or EIO hard disk .................... 199
ENWW ix
Use FTP to upload the firmware through a browser ....................................... 212
Use FTP to upgrade the firmware on a network connection ........................... 213
Use HP Web Jetadmin to upgrade the firmware ............................................. 214
Use MS-DOS commands to upgrade the firmware ......................................... 214
AREA 5: Clear jams in Tray 2 and the internal paper path ............................. 233
AREA 7: Clear jams in optional Trays 3, 4, and 5 ........................................... 239
AREA 8: Clear jams in the optional finishing devices ..................................... 242
Clear jams in the output-accessory bridge ..................................... 242
Clear jams in the sorter area .......................................................... 243
Clear jams in the booklet maker ..................................................... 244
Clear staple jams in the main stapler ............................................. 247
Clear staple jams in the booklet maker .......................................... 248
x ENWW
Respond to control panel error messages ...................................................... 261
Clean the registration second transfer assembly ........................... 262
Appendix A Supplies and accessories
ENWW xi
Appendix B Product specifications
Appendix C Regulatory information
Multiple returns (more than one cartridge) ..................................... 287
Single returns ................................................................................. 287
Disposal of waste equipment by users in private households in the European Union .... 288
xii ENWW
ENWW xiii
xiv ENWW
1 Product basics
●
●
●
ENWW 1
Product introduction
Figure 1-1 HP Color LaserJet CM6049f MFP (CE799A)
The HP Color LaserJet CM6049f MFP comes standard with the following items:
● 100-sheet multipurpose input tray (Tray 1)
● 40 ppm
● Four 500-sheet input trays
● Automatic document feeder (ADF) that holds up to 50 pages
● HP Jetdirect embedded print server for connecting to a 10/100Base-TX network
● 512 megabytes (MB) of random access memory (RAM)
● Duplexer
● Hard drive
● Analog fax
2 Chapter 1 Product basics ENWW
Product features
Table 1-1 Features
Speed and throughput
Resolution
Memory
User interface
Drivers
Languages and fonts
Print cartridges/image drums (4 of each)
● Print up to 40 ppm on letter-size paper.
● Less than 11 seconds to print the first page
● Recommended maximum monthly print volume of 15,000 pages
● An 835 megahertz (MHz) microprocessor
● Duplex at speed
● 600 dots per inch (dpi) with Image Resolution Enhancement technology 4800 for optimum overall imaging
● 1200 x 600 dpi for detailed line work and small text
● 512 MB of random-access memory (RAM), expandable to 768 MB by using 200-pin small outline dual inline memory modules (SODIMM) that support 128 or 256 MB of RAM.
● Memory Enhancement technology (MEt) automatically compresses data to use RAM more efficiently.
● HP Easy Select Control Panel
HP provides the following drivers for downloading:
● HP Universal Print Driver (UPD): Postscript, PCL 6, PCL 5
● Mac Driver
● Linux
● SAP
● UNIX Model Script
Drivers for this product are available at www.hp.com/go/cljcm6049mfp_software or your country/ region alternative.
● HP Printer Control Language (PCL) 6
● HP Universal Printer Driver (UPD) PCL 5
● HP Universal Printer Driver (UPD) postscript (PS)
● Printer Management Language
● 80 scalable TrueType PS typefaces
● Two-part toner/imaging system
● Black print cartridges print up to 19,500 pages at 5% coverage
● Color print cartridges print up to 21,000 pages at 5% coverage
● Image drums print up to 35,000 pages at 5% coverage
● Authentic HP print cartridge detection
● Automatic toner strip remover
ENWW Product features 3
Table 1-1 Features (continued)
Paper-handling ● Input
◦ Tray 1 (multipurpose tray): A multipurpose tray for paper, transparencies, labels,
envelopes and other paper types. See Supported paper types on page 98 for a list
of paper types. The tray holds up to 100 sheets of paper, 50 transparencies, or
10 envelopes. See Supported paper and print media sizes on page 95 .
◦
◦
◦
Tray 2, 3, 4, and 5: 500-sheet trays. These trays automatically detect common paper sizes and allow printing on custom-size paper. Tray 2 supports up to 279 x 432 mm
(11 x 17 inches) and A3 paper sizes, and Trays 3,4, and 5 support sizes up to 305 x
457 mm (12 x 18 inches), and SRA3. See
see Supported paper types on page 98 .
Automatic document feeder (ADF): Holds up to 50 sheets of paper.
◦
ADF duplex scanning: The ADF has an automatic duplexer for scanning two-sided documents.
Duplex printing: Provides automatic two-sided printing (printing on both sides of the paper).
Supported operating systems
Connectivity
● Output
◦ Standard output bin: The standard output bin is located underneath the scanner on the top of the product. This bin can hold up to 500 sheets of paper. The product provides a sensor that indicates when the bin is full.
◦
The paper size range for automatic duplex printing is 175 mm to 320 mm (6.9 to 12.6
inches) x 210 mm to 457 mm (8.3 to 18 inches). The media weight range is 60–220 g/m² (16-58 lb).
Optional 3-bin stapler/stacker: Provides job separation in multiple output bins, convenient stapling (up to 50-sheet jobs), job offset capability, and additional output capacity. The stacker has three bins: a 100-sheet bin, a 500-sheet bin, and a 1000sheet bin.
◦ Optional booklet maker finisher: Provides convenient stapling (up to 50-sheet jobs), saddle-stitching (up to 15-sheet booklets), single-sheet v-folding, job separation and offset capability, as well as additional output capacity. The booklet maker finisher has three bins: two 1000-sheet bins and one bin that can hold up to 25 saddle-stitched booklets.
◦ ADF output bin: The ADF output bin is underneath the ADF input tray. The bin holds up to 50 sheets of paper, and the product automatically stops when this bin is full.
● Windows 2000 ®
● Windows XP ®
● Windows Server 2003 ®
● Windows Server 2008 ®
● Windows Vista™
● Macintosh OS
● Local area network (LAN) connector (RJ-45) for the embedded HP Jetdirect print server
● One enhanced input/output (EIO) slot
● USB 2.0 connection
● Optional analog fax card
4 Chapter 1 Product basics ENWW
Table 1-1 Features (continued)
Environmental features ● Sleep setting saves energy.
Security features
Copying and sending
● High content of recyclable components and materials.
● Secure Disk Erase
● Security lock (optional)
● Job retention
● User PIN authentication for stored jobs
● DSS authentication
● IPv6 security
● Modes for text, graphics, and mixed text and graphics formats
● Job-interrupt feature
● Multiple pages per sheet
● Control panel animations (for example, jam recovery)
● Scan and send to e-mail
◦ Local address book for e-mail and fax
◦ LDAP addressing
● Send to folder
● Automatic duplex (two-sided) scanning
ENWW Product features 5
Product walkaround
Front view
HP Color LaserJet CM6049f MFP
1 2 3 4
10
9
8
5
6
7
7
8
9
10
3
4
1
2
5
6
Control panel
Automatic Document Feeder (ADF) top cover
ADF input tray for copy/scan/fax originals
ADF output bin
Right-door (provides access to the transfer unit, transfer roller, and fuser unit)
On/Off switch
Lower right door
Trays 2, 3, 4 and 5
Front cover (provides access to print cartridges and image drums)
Output bin
6 Chapter 1 Product basics ENWW
Back view
1
2
Interface ports and formatter
Lock lever for additional input bins
ENWW Product walkaround 7
Interface ports
The product has five ports for connecting to a computer or a network. The ports are at the left, rear corner of the product.
3
4
5
6
1
2
3
4
1
2
5
6
Fax connection (when installed)
Scanner cable
Access port for Kensington lock
USB 2.0 port
EIO expansion slot
Network port
8 Chapter 1 Product basics ENWW
Serial number and model number location
The model number and serial number are listed on identification labels located on the rear of the printer.
The serial number contains information about the country/region of origin, the printer version, production code, and the production number of the printer.
Model name
HP Color LaserJet CM6049f MFP
Model number
CE799A
ENWW Product walkaround 9
10 Chapter 1 Product basics ENWW
2 Control panel
●
●
Navigate the Administration menu
●
●
●
●
●
●
●
●
●
●
ENWW 11
Use the control panel
The control panel has a VGA touchscreen that provides access to all device functions. Use the buttons and numeric keypad to control jobs and the device status. The LEDs indicate overall device status.
Control-panel layout
The control panel includes a touchscreen graphical display, job-control buttons, a numeric keypad, and three light-emitting diode (LED) status lights.
1 2 3 4
1
2
10
9
8
7
Touchscreen graphical display
Numeric keypad
5
6
5
6
3
4
7
8
9
10
Reset button
Sleep button
Stop button
Start button
Attention light
Ready light
Data light
Contrast-adjustment dial
Use the touchscreen to open and set up all device functions.
Allows you to type numeric values for number of copies required and other numeric values.
Resets the job settings to factory or user-defined default values.
If the device is inactive for a long period of time, it automatically enters a sleep mode. To place the device into sleep mode or to reactivate the device, press the Sleep button.
Stops the active job and opens the Job Status screen.
Begins a copy job, starts digital sending, or continues a job that has been interrupted.
The Attention light indicates that the device has a condition that requires intervention. Examples include an empty paper tray or an error message on the touchscreen.
The Ready light indicates that the device is ready to begin processing any job.
The Data light indicates that the device is receiving data.
Turn the dial to adjust the contrast of the touchscreen display for your viewing angle.
12 Chapter 2 Control panel ENWW
Home screen
The home screen provides access to the device features, and it indicates the current status of the device.
NOTE: Depending on how the device has been configured, the features that appear on the home screen can vary.
2 3 4 5
6
1
1
9
Features
2 Device status line
5
6
3
4
7
Copy type
Copy count
Help button
Scroll bar
Sign Out
8
9
Network Address
Date and time
8 7
Depending on how the system administrator has configured the device, the features that appear in this area can include any of the following items:
● Copy
● Fax
● Secondary E-mail
● Job Status
● Network Folder
● Job Storage
● Workflow
● Supplies Status
● Administration
The status line provides information about the overall device status. Various buttons appear in this area, depending on the current status. For a description of each button that can appear in the status line, see
Buttons on the touchscreen on page 14 .
Shows whether copies are color.
The copy count box indicates the number of copies that the device is set to make.
Touch the Help button to open the embedded help system.
Touch the up or down arrows on the scroll bar to see the complete list of available features.
Touch Sign Out to sign out of the device if you have signed in for access to restricted features.
After you sign out, the device restores all options to the default settings.
Touch Network Address to find information about the network connection.
The current date and time appear here. The system administrator can select the format that the device uses to show the date and time, for example 12-hour format or 24-hour format.
ENWW Use the control panel 13
Buttons on the touchscreen
The status line on the touchscreen provides information about the status of the device. Various buttons can appear in this area. The following table describes each button.
Home button . Touch the home button to go to the Home screen from any other screen.
Start button . Touch the Start button to begin the action for the feature that you are using.
NOTE: The name of this button changes for each feature. For example, in the Copy feature, the button is named Start Copy .
Stop button . If the device is processing a print or fax job, the Stop button appears instead of the Start button. Touch the Stop button to halt the current job. The device prompts you to cancel the job or to resume it.
Error button . The error button appears whenever the device has an error that requires attention before it can continue. Touch the error button to see a message that describes the error. The message also has instructions for solving the problem.
Warning button . The warning button appears when the device has a problem but can continue functioning. Touch the warning button to see a message that describes the problem. The message also has instructions for solving the problem.
Help button . Touch the help button to open the built-in online Help system. For more information, see
Control-panel help system on page 14 .
Control-panel help system
The device has a built-in Help system that explains how to use each screen. To open the Help system, touch the Help button in the upper-right corner of the screen.
For some screens, the Help opens to a global menu where you can search for specific topics. You can browse through the menu structure by touching the buttons in the menu.
For screens that contain settings for individual jobs, the Help opens to a topic that explains the options for that screen.
If the device alerts you of an error or warning, touch the error or warning button to open a message that describes the problem. The message also contains instructions to help solve the problem.
14 Chapter 2 Control panel ENWW
Navigate the Administration menu
From the Home screen, touch Administration to open the menu structure. You might need to scroll to the bottom of the Home screen to see this feature.
The Administration menu has several sub-menus, which are listed on the left side of the screen. Touch the name of a menu to expand the structure. A plus sign (+) next to a menu name means that it contains sub-menus. Continue opening the structure until you reach the option that you want to configure. To return to the previous level, touch Back .
To exit the Administration menu, touch the Home button in the upper-left corner of the screen.
The device has built-in Help that explains each of the features that are available through the menus.
Help is available for many menus on the right-hand side of the touchscreen. Or, to open the global Help system, touch the Help button in the upper-right corner of the screen.
The tables in the sections that follow indicate the overall structure of each menu under the Administration menu.
ENWW Navigate the Administration menu 15
Information menu
Administration > Information
Use this menu to print information pages and reports that are stored internally on the device.
Table 2-1 Information menu
Menu item Sub-menu item Sub-menu item Values Description
Configuration/Status
Pages
Fax Reports
Administration Menu
Map
Configuration/status
Pages
Supplies Status
Page
Usage Page
Color Usage Job Log
File Directory
Fax Activity Log
Fax Call Report
Billing Codes Report
Blocked Fax List
Speed Dial List
Fax Call Report
Shows the basic structure of the
Administration menu and current administration settings.
A set of configuration pages that show the current device settings.
Shows the status of supplies such as cartridges, maintenance kits, and staples.
Shows information about the number of pages that have been printed on each paper type and size.
A directory page that contains job-by-job color usage information. Page content includes the user name, application name, and number of black-only pages and color pages.
A directory page that contains information for any mass-storage devices, such as flash drives, memory cards, or hard disks, that are installed in this device.
Contains a list of the faxes that have been sent from or received by this device.
A detailed report of the last fax operation, either sent or received.
Choose whether or not to include a thumbnail of the first page of the fax on the call report.
Thumbnail on Report Yes
No (default)
When to Print Report Never auto print
Print after any fax job
Print after fax send jobs
Print after any fax error (default)
Print after send errors only
Print after receive errors only
A list of billing codes that have been used for outgoing faxes. This report shows how many sent faxes were billed to each code.
A list of phone numbers that are blocked from sending faxes to this device.
Print Shows the speed dials that have been set up for this device.
16 Chapter 2 Control panel ENWW
Table 2-1 Information menu (continued)
Menu item Sub-menu item Sub-menu item
Sample Pages/Fonts Demonstration Page
RGB Samples
Values
CMYK Samples
PCL Font List
PS Font List
Description
Printout of a page highlighting the print capabilities of the product.
Printout of color samples for different RGB values. The samples act as a guide for color matching.
Printout of color samples for different CMYK values. The samples act as a guide for color matching.
A list of printer control language (PCL) fonts that are currently available on the device.
A list of PostScript (PS) fonts that are currently available on the device.
ENWW Information menu 17
Default Job Options menu
Administration > Default Job Options
Use this menu to define the default job options for each function. These are used if the user does not specify other options when creating the job.
Default Options for Originals
Administration > Default Job Options > Default Options For Originals
Table 2-2 Default Options for Originals menu
Menu item Values Description
Paper Size
Number of Sides
Orientation
Optimize Text/Picture
Select a paper size from the list.
Select the paper size that is most often used for copy or scan originals.
1 Select whether copy or scan originals are most often single-sided or double-sided.
2
Portrait
Landscape
Select the orientation that is most often used for copy or scan originals. Select Portrait if the short edge is at the top or select
Landscape if the long edge is at the top.
Manually Adjust
Text
Printed Picture
Photograph
Optimize the output for a particular type of original: text, pictures, or a mixture of both.
If you select Manually Adjust , specify the mix of text and pictures that is used most often.
18 Chapter 2 Control panel ENWW
Image adjustment
Administration > Default Job Options > Image Adjustment
Table 2-3 Image Adjustment menu
Menu item Values Description
Darkness
Background Cleanup
Sharpness
Select a value.
Select the level of density (darkness) for the output.
Adjust the value within the range. Increase the Background Removal setting to remove faint images from the background or to remove a light background color.
Adjust the value within the range. Adjust the Sharpness setting to clarify or soften the image.
ENWW Default Job Options menu 19
Default Copy Options
Administration > Default Job Options > Default Copy Options
Table 2-4 Default Copy Options menu
Menu item Sub-menu item Values Description
Number of Copies Set the default number of copies for a copy job.
Number of Sides
Color/Black
Staple/Collate
Output Bin
Edge-To-Edge
Auto Include Margins
Staple
Collate
Type the number of copies. The factory default setting is 1.
1
2
Auto detect
Color
Black (default)
None (default)
One left angled
Two left
Two top
One right angled
Two right
Off
On (default)
<Binname>
Normal (recommended)
(default)
Edge-To-Edge Output
Off (default)
On
Set the default number of sides for copies.
Choose whether the default copy mode is color or black.
Set up options for stapling and collating sets of copies.
If Collate is selected, the device prints a complete copy before starting on the next copy. Otherwise, the device prints the first page of all copies before printing the second page, and so on.
The staple and collate feature may not be present in your product. These features depend on the optional output accessory installed.
Select the default output bin for copies.
This option is available only if an optional output accessory is installed.
If the original document is printed close to the edges, use the Edge-To-Edge feature to avoid shadows along the edges. Combine this feature with the Reduce/
Enlarge feature to ensure that the entire page appears on the copies.
This feature automatically reduces the image size during scanning so the margins are included.
20 Chapter 2 Control panel ENWW
Default Fax Options
Administration > Default Job Options > Default Fax Options
Table 2-5 Fax Send menu
Menu item Sub-menu item Values Description
Resolution
Fax Header
Standard (100x200dpi)
(default)
Fine (200x200dpi)
Superfine (300x300dpi)
Prepend (default)
Overlay
Set the resolution for sent documents. Higher resolution images have more dots per inch (dpi), so they show more detail. Lower resolution images have fewer dots per inch and show less detail, but the file size is smaller.
Select the position of the fax header on the page.
Select Prepend to print the fax header above the fax content and move the fax content down on the page.
Select Overlay to print the fax header over the top of the fax contents without moving the contents down.
Using this option could prevent a single-page fax from flowing onto another page.
Table 2-6 Fax Receive menu
Menu item Sub-menu item
Fax Forwarding Fax Forwarding
Values
Off (default)
Custom
Stamp Received Faxes
Fit to Page
Create PIN
Enabled
Disabled (default)
Enabled (default)
Disabled
Fax Paper Tray
Output Bin
Select from the list of trays.
The default setting is
Automatic .
<Binname>
Description
To forward received faxes to another fax device, select
Fax Forwarding and Custom . Then type the number of the other fax device into the Fax Forwarding Number field. When you select this menu item for the first time, you are prompted to set up a PIN. Type that PIN every time you use this menu. This is the same PIN that is used to access the Fax Printing menu.
Add the date, time, senders phone number, and page number to each page of the faxes that this device receives.
Shrink faxes that are larger than Letter-size or A4-size so that they can fit onto a Letter-size or A4-size page.
If it this feature set to Disabled , faxes larger than Letter or A4 will flow across multiple pages.
Select the tray that holds the size and type of paper that you want to use for incoming faxes.
Select the default output bin, if applicable, to use for faxes.
ENWW Default Job Options menu 21
Default E-mail Options
Administration > Default Job Options > Default E-mail Options
Menu item
Document File Type
Output Quality
Resolution
Color/Black
TIFF Version
Values
PDF (default)
JPEG
TIFF
M-TIFF
High (large file)
Medium (default)
Low (small file)
300 DPI
200 DPI
150 DPI (default)
75 DPI
Color scan (default)
Black/white scan
TIFF 6.0
(default)
TIFF (Post 6.0)
Description
Select the file format for the e-mail.
Selecting higher quality for output increases the size of the output file.
Select the resolution. Use a lower setting to create smaller files.
Specify whether the e-mail will be in black or in color.
Specify the TIFF version to use when saving scanned files.
22 Chapter 2 Control panel ENWW
Default Send to Folder Options
Administration > Default Job Options > Default Send To Folder Options
Menu item
Color/Black
Document File Type
TIFF version
Output Quality
Resolution
Values
Color scan
Black/white scan (default)
PDF (default)
M-TIFF
TIFF
JPEG
TIFF 6.0
(default)
TIFF (post 6.0)
High (large file)
Medium (default)
Low (small file)
75 DPI
150 DPI (default)
200 DPI
300 DPI
400 DPI
600 DPI
Description
Specify whether the file will be in black or in color.
Select the file format for the file.
Specify the TIFF version to use when saving scanned files.
Selecting higher quality for output increases the size of the output file.
Select the resolution. Use a lower setting to create smaller files.
ENWW Default Job Options menu 23
Default Print Options
Administration > Default Job Options > Default Print Options
Table 2-7 Default Print Options menu
Menu item Sub-menu item Values Description
Copies Per Job
Default Paper Size
Default Custom Paper
Size
Output Bin
Print Sides
Unit of measure
X Dimension
Y Dimension
Type a value.
Set the default number of copies for print jobs.
(List of supported sizes) Select a paper size.
Millimeters Configure the default paper size that is used when the user selects Custom as the paper size for a print job.
Inches
Configure the width measurement for the Default
Custom Paper Size .
Configure the height measurement for the Default
Custom Paper Size .
<binname>
1-sided
2-sided
Select the default output bin for print jobs. If optional trays are installed, output bin options vary.
Select whether print jobs are single-sided or doublesided by default.
24 Chapter 2 Control panel ENWW
Time/Scheduling menu
Administration > Time/Scheduling
Use this menu to set options for setting the time and for setting the device to enter and exit sleep mode.
NOTE: Values shown with "(default)" are the factory-default values. Some menu items have no default.
Table 2-8 Time/Scheduling menu
Menu item Sub-menu item
Date/Time Date Format
Date
Sub-menu item Values
YYYY/MMM/DD
(default)
MMM/DD/YYYY
DD/MMM/YYYY
Description
Use this feature to set the current date and time, and to set the date format and time format that are used to time-stamp outgoing faxes.
Time Format
Month
Day
Year
Time
12 hour (AM/PM)
(default)
24 hour
Sleep Delay
Hour
Minute
AM
PM
Use this feature to select the time interval that the device should remain inactive before entering Sleep Mode.
Wake Time Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
1 Minute
20 minutes
30 minutes (default)
45 minutes
1 hour (60 minutes)
90 minutes
2 hours
4 hours
Off (default)
Custom
Select Custom to set a wake time for each day of the week. The device exits sleep mode according to this schedule. Using a sleep schedule helps conserve energy and prepares the device for use so that users do not have to wait for it to warm up.
ENWW Time/Scheduling menu 25
Table 2-8 Time/Scheduling menu (continued)
Menu item Sub-menu item Sub-menu item
Sleep Time
FAX Printing
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Create PIN
Values
Off (default)
Custom
Description
Use this feature to set a sleep time for each day of the week for periods when the device will not likely be in use (for example, at a certain time each evening). Setting a sleep time makes the device automatically go into a low-power mode. Select a day and then select Custom to set up a custom sleep time schedule.
If you have concerns about the security of private faxes, use this feature to store faxes rather than having them automatically print by creating a printing schedule. When you select this menu item for the first time, you are prompted to set up a PIN. Type that PIN every time you use this menu.
26 Chapter 2 Control panel ENWW
Management menu
Administration > Management
Use this menu to set up global device-management options.
NOTE: Values shown with "(default)" are the factory-default values. Some menu items have no default.
Table 2-9 Management menu
Menu item Sub-menu item
Network Address Button Display
Hide (default)
Stored Job Management Quick Copy Job Storage
Limit
Quick Copy Job Held
Timeout
Sleep mode
Manage Supplies Replace Supplies
Supply Low/Order
Threshold
Color Supply Out
Values Description
Use this feature to display the Network Address button on the Home screen.
Select the maximum number of jobs to store
Off (default)
1 Hour
4 Hours
1 Day
Use this menu to view and manage any jobs that are stored on the device.
1 Week
Disable
Use Sleep Delay (default)
Use this feature to customize the sleep mode settings for this device.
Select Use Sleep Delay to set the device to enter sleep mode after the delay that is specified in the Time/
Scheduling menu.
Stop at low
Stop at out (default)
Override at out
Override at out
1
2
This menu sets the product behavior for when a print cartridge, fuser kit, or transfer kit is low. Choose Stop at low to stop printing when a supply reaches a low condition. Choose Stop at out to allow the product to continue printing until a color print cartridge is empty.
Choose Override at out 1 to allow the product to continue printing when the cartridges are empty or when the other supplies are worn out. The product stops printing when the toner collection units are full.
Using this option could reduce print quality.
Select a value in the range. The default is 5%.
Stop (default)
Auto-continue black
Choose Override at out 2 to allow the product to keep printing when the cartridges are empty; when other supplies are worn out; and when the waste toner collection units are full. Using this option can damage the device.
Use this menu to carry out administrative supply management tasks such as changing the threshold when supplies should be ordered.
This menu sets the product behavior when a color supply is empty. When Auto-continue black is selected, the product will continue printing using black toner only.
ENWW Management menu 27
Table 2-9 Management menu (continued)
Menu item
Restrict Color Use
Color/Black Mix
Sub-menu item
Color printing access
Color copying access
Values
Enable Color (default)
Color If Allowed
Disable Color
Enable Color (default)
Disable Color
Automatic (default)
Mostly color pages
Mostly black pages
Description
This item allows the administrator to disable or restrict color printing. To use the Color If Allowed setting, set up user permissions and/or application permissions in the embedded Web server or Web Jetadmin.
This item allows the administrator to disable or restrict color copying.
This item controls how the engine switches from color mode to monochrome mode for maximum performance and print cartridge life.
Choose Automatic to reset the product to the factory default setting.
Choose Mostly color pages if nearly all of your print jobs are color with high page coverage.
Choose Mostly black pages if you print mostly monochrome jobs or a combination of color and monochrome jobs.
28 Chapter 2 Control panel ENWW
Initial Setup menu
Administration > Initial Setup
NOTE: Values shown with "(default)" are the factory-default values. Some menu items have no default.
Networking and I/O
Administration > Initial Setup > Networking and I/O
Table 2-10 Networking and I/O
Menu item Sub-menu item Values
I/O Timeout
Embedded Jetdirect
Description
Select a value in the range. The factory default setting is 15 seconds.
I/O timeout refers to the elapsed time before a print job fails. If the stream of data that the device receives for a print job gets interrupted, this setting indicates how long the device will wait before it reports that the job has failed.
See
Table 2-11 Jetdirect menus on page 29 for the list of options.
Table 2-11 Jetdirect menus
Menu item Sub-menu item
TCP/IP Enable
Host Name
IPV4 Settings
Sub-menu item
Config Method
Values and Description
Off : Disable the TCP/IP protocol.
On (default): Enable the TCP/IP protocol.
An alphanumeric string, up to 32 characters, used to identify the device. This name is listed on the
HP Jetdirect configuration page. The default host name is NPIxxxxxx, where xxxxxx is the last six digits of the
LAN hardware (MAC) address.
Specifies the method that TCP/IPv4 parameters will be configured on the HP Jetdirect print server.
Bootp : Use BootP (Bootstrap Protocol) for automatic configuration from a BootP server.
DHCP : Use DHCP (Dynamic Host Configuration
Protocol) for automatic configuration from a DHCPv4 server. If selected and a DHCP lease exists, DHCP
Release and DHCP Renew menus are available to set
DHCP lease options.
Auto IP : Use automatic link-local IPv4 addressing. An address in the form 169.254.x.x is assigned automatically.
Manual : Use the Manual Settings menu to configure
TCP/IPv4 parameters.
ENWW Initial Setup menu 29
Table 2-11 Jetdirect menus (continued)
Menu item Sub-menu item Sub-menu item
Default IP
30
IPV6 Settings
Chapter 2 Control panel
DHCP Release
DHCP Renew
Primary DNS
Secondary DNS
Enable
Address
DHCPV6 Policy
Values and Description
Specify the IP address to default to when the print server is unable to obtain an IP address from the network during a forced TCP/IP reconfiguration (for example, when manually configured to use BootP or
DHCP).
Auto IP : A link-local IP address 169.254.x.x is set.
Legacy : The address 192.0.0.192 is set, consistent with older HP Jetdirect devices.
This menu appears if Config Method was set to
DHCP and a DHCP lease for the print server exists.
No (default): The current DHCP lease is saved.
Yes : The current DHCP lease and the leased IP address are released.
This menu appears if Config Method was set to
DHCP and a DHCP lease for the print server exists.
No (default): The print server does not request to renew the DHCP lease.
Yes : The print server requests to renew the current
DHCP lease.
Specify the IP address (n.n.n.n) of a Primary DNS
Server.
Specify the IP address (n.n.n.n) of a Secondary
Domain Name System (DNS) Server.
Use this item to enable or disable IPv6 operation on the print server.
Off : IPv6 is disabled.
On (default): IPv6 is enabled.
Manual Settings: Use this item to manually set IPv6 addresses on the print server.
Enable : Select this item and choose On to enable manual configuration, or Off to disable manual configuration.
Address : Use this item to type a 32 hexadecimal digit
IPv6 node address that uses the colon hexadecimal syntax.
Router Specified : The stateful auto-configuration method to be used by the print server is determined by a router. The router specifies whether the print server obtains its address, its configuration information, or both from a DHCPv6 server.
Router Unavailable : If a router is not available, the print server should attempt to obtain its stateful configuration from a DHCPv6 server.
Always : Whether or not a router is available, the print server always attempts to obtain its stateful configuration from a DHCPv6 server.
ENWW
Table 2-11 Jetdirect menus (continued)
Menu item Sub-menu item
Proxy Server
Sub-menu item
Primary DNS
Secondary DNS
IPX/SPX
AppleTalk
DLC/LLC
Proxy Port
Enable
Frame Type
Enable
Enable
Values and Description
Use this item to specify an IPv6 address for a primary
DNS server that the print server should use.
Use this item to specify an IPv6 address for a secondary DNS server that the print server should use.
Specifies the proxy server to be used by embedded applications in the device. A proxy server is typically used by network clients for Internet access. It caches
Web pages, and provides a degree of Internet security, for those clients.
To specify a proxy server, enter its IPv4 address or fully-qualified domain name. The name can be up to
255 octets.
For some networks, you may need to contact your
Independent Service Provider (ISP) for the proxy server address.
Type the port number used by the proxy server for client support. The port number identifies the port reserved for proxy activity on your network, and can be a value from 0 to 65535.
Off : Disable the IPX/SPX protocol.
On (default): Enable the IPX/SPX protocol.
Selects the frame-type setting for your network.
Auto : Automatically sets and limits the frame type to the first one detected.
EN_8023 , EN_II , EN_8022 , and EN_SNAP : Frametype selections for Ethernet networks.
Off : Disable the AppleTalk protocol.
On (default): Enable the AppleTalk protocol.
Off : Disable the DLC/LLC protocol.
On (default): Enable the DLC/LLC protocol.
ENWW Initial Setup menu 31
Table 2-11 Jetdirect menus (continued)
Menu item Sub-menu item
Security Print Sec Page
Sub-menu item
Secure Web
Diagnostics
IPSEC
Reset Security
Embedded Tests
LAN HW Test
HTTP Test
Values and Description
Yes (default): Prints a page that contains the current security settings on the HP Jetdirect print server.
No : A security settings page is not printed.
For configuration management, specify whether the embedded Web server will accept communications using HTTPS (Secure HTTP) only, or both HTTP and
HTTPS.
HTTPS Required (default): For secure, encrypted communications, only HTTPS access is accepted. The print server will appear as a secure site.
HTTP/HTTPS optional : Access using either HTTP or
HTTPS is permitted.
Specify the Firewall status on the print server.
Keep : Firewall status remains the same as currently configured.
Disable : Firewall operation on the print server is disabled.
Specify whether the current security settings on the print server will be saved or reset to factory defaults.
No : The current security settings are maintained.
Yes : Security settings are reset to factory defaults.
This menu provides tests to help diagnose network hardware or TCP/IP network connection problems.
Embedded tests help to identify whether a network fault is internal or external to the device. Use an embedded test to check hardware and communication paths on the print server. After you select and enable a test and set the execution time, you must select Execute to initiate the test.
Depending on the execution time, a selected test runs continuously until either the device is turned off, or an error occurs and a diagnostic page is printed.
CAUTION: Running this embedded test will erase your TCP/IP configuration.
This test performs an internal loopback test. An internal loopback test will send and receive packets only on the internal network hardware. There are no external transmissions on your network.
Select Yes to choose this test, or No to not choose it.
This test checks operation of HTTP by retrieving predefined pages from the device, and tests the embedded Web server.
Select Yes to choose this test, or No to not choose it.
32 Chapter 2 Control panel ENWW
Table 2-11 Jetdirect menus (continued)
Menu item Sub-menu item
Ping Test
Dest Type
Dest IPv4
Dest IPv6
Packet Size
Timeout
Count
Print Results
Sub-menu item
SNMP Test
Data Path Test
Select All Tests
Execution Time [H]
Execute
Execute
Values and Description
This test checks operation of SNMP communications by accessing predefined SNMP objects on the device.
Select Yes to choose this test, or No to not choose it.
This test helps to identify data path and corruption problems on an HP postscript level 3 emulation device.
It sends a predefined PS file to the device, However, the test is paperless; the file will not print.
Select Yes to choose this test, or No to not choose it.
Use this item to select all available embedded tests.
Select Yes to choose all tests. Select No to select individual tests.
Use this item to specify the length of time (in hours) that an embedded test will be run. You can select a value from 1 to 60 hours. If you select zero (0), the test runs indefinitely until an error occurs or device is turned off.
Data gathered from the HTTP, SNMP, and Data Path tests is printed after the tests have completed.
No : Do not initiate the selected tests.
Yes : Initiate the selected tests.
This test is used to check network communications.
This test sends link-level packets to a remote network host, then waits for an appropriate response. To run a ping test, set the following items:
Specify whether the target device is an IPv4 or IPv6 node.
Type the IPv4 address.
Type the IPv6 address.
Specify the size of each packet, in bytes, to be sent to the remote host. The minimum is 64 (default) and the maximum is 2048.
Specify the length of time, in seconds, to wait for a response from the remote host. The default is 1 and the maximum is 100.
Specify the number of ping test packets to send for this test. Select a value from 1 to 100. To configure the test to run continuously, select 0.
If the ping test was not set for continuous operation, you can choose to print the test results. Select Yes to print results. If you select No (default), results are not printed.
Specify whether to initiate the ping test. Select Yes to initiate the test, or No to not run the test.
ENWW Initial Setup menu 33
Table 2-11 Jetdirect menus (continued)
Menu item Sub-menu item
Ping Results
Sub-menu item
Packets Sent
Packets Received
Percent Lost
RTT Min
RTT Max
RTT Average
Ping In Progress
Refresh
Values and Description
Use this item to view the ping test status and results using the control panel display. You can select the following items:
Shows the number of packets (0 - 65535) sent to the remote host since the most recent test was initiated or completed.
Shows the number of packets (0 - 65535) received from the remote host since the most recent test was initiated or completed.
Shows the percent of ping test packets that were sent with no response from the remote host since the most recent test was initiated or completed.
Shows the minimum detected roundtrip- time (RTT), from 0 to 4096 milliseconds, for packet transmission and response.
Shows the maximum detected roundtrip- time (RTT), from 0 to 4096 milliseconds, for packet transmission and response.
Shows the average round-trip-time (RTT), from 0 to
4096 milliseconds, for packet transmission and response.
Shows whether a ping test is in progress. Yes indicates a test in progress, and No indicates that a test completed or was not run.
When viewing the ping test results, this item updates the ping test data with current results. Select Yes to update the data, or No to maintain the existing data.
However, a refresh automatically occurs when the menu times out or you manually return to the main menu.
34 Chapter 2 Control panel ENWW
Table 2-11 Jetdirect menus (continued)
Menu item Sub-menu item
Link Speed
Sub-menu item
Print Protocols
Values and Description
The link speed and communication mode of the print server must match the network. The available settings depend on the device and installed print server. Select one of the following link configuration settings:
CAUTION: If you change the link setting, network communications with the print server and network device might be lost.
Auto (default): The print server uses auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/switch port. (A
1000T half-duplex selection is not supported.)
10T Half : 10 Mbps, half-duplex operation.
10T Full : 10 Mbps, Full-duplex operation.
100TX Half : 100 Mbps, half-duplex operation.
100TX Full : 100 Mbps, full-duplex operation.
100TX Auto : Limits auto-negotiation to a maximum link speed of 100 Mbps.
1000TX Full : 1000 Mbps, full-duplex operation.
Use this item to print a page that lists the configuration of the following protocols: IPX/SPX, Novell NetWare,
AppleTalk, DLC/LLC.
ENWW Initial Setup menu 35
Fax Setup
Administration > Initial Setup > Fax Setup
Table 2-12 Fax Setup menu
Menu item Sub-menu item Sub-menu item
Required Settings Country/Region
PC Fax Send
Date/Time
Fax Header
Information
Date Format
Date
Time Format
Time
Phone Number
Company Name
Values
(Countries/regions listed)
Description
Configure the settings that are legally required for outgoing faxes.
Disabled
Enabled (default)
Use this feature to enable or disable PC Fax
Send. PC Fax Send enables users to send faxes through the device from their computers if they have the Send Fax driver installed on their PC.
36 Chapter 2 Control panel ENWW
Table 2-12 Fax Setup menu (continued)
Menu item Sub-menu item Sub-menu item
Fax Send Settings Fax Dial Volume
Error Correction
Mode
JBIG Compression
Maximum Baud Rate
TCF T.30 Delay
Timer
TCF Extend
Dialing Mode
Redial On Busy
Redial On No Answer
Values Description
Off
Low (default)
High
Enabled
Disabled
Enabled
Disabled
(default)
(default)
Use this feature to set the volume of the tones that you hear while the device dials the fax number.
When Error Correction Mode is enabled and an error occurs during fax transmission, the device sends or receives the error portion again.
JBIG compression reduces fax-transmission time, which can result in lower phone charges. However, using JBIG compression sometimes causes compatibility problems with older fax machines. If this occurs, turn off
JBIG compression.
Select a value from the list. The default is
33.6K.
Use this feature to set the maximum baud rate for receiving faxes. This can be used as a diagnostic tool for troubleshooting fax problems.
Default (default)
Custom
This setting should be left at the default value and only changed when directed by an HP technical support agent. Adjustment procedures associated with this setting are beyond the scope of this guide.
Default
Custom
Tone
(default)
(default)
This setting should be left at the default value and only changed when directed by an HP technical support agent. Adjustment procedures associated with this setting are beyond the scope of this guide.
Select whether the device should use tone or pulse dialing.
Pulse
The range is between
0 and 9. The factory default is 3 times.
Type the number of times the device should attempt to redial if the line is busy.
Never (default)
Once
Use this feature to specify the number of times the device should attempt to dial if the recipient fax number does not answer.
Twice NOTE: Twice is available in locations other than the United States and Canada.
ENWW Initial Setup menu 37
Table 2-12 Fax Setup menu (continued)
Menu item Sub-menu item
Redial Interval
Detect Dial Tone
Dialing Prefix
Billing Codes
Fax Receive Settings Rings To Answer
Ring Interval
Ring Frequency
Ringer Volume
Blocked Fax
Numbers
Sub-menu item
Add Blocked
Numbers
Remove Blocked
Numbers
Clear All Blocked
Numbers
Values Description
The range is between
1 and 5 minutes. The factory default is 5 minutes.
Use this feature to specify the number of minutes between dialing attempts if the recipient number is busy or not answering.
Enabled
Disabled
Off
Custom
(default)
(default)
Use this feature to specify whether the device should check for a dial tone before sending a fax.
Use this feature to specify a prefix number that must be dialed when sending faxes from the device.
Off (default)
Custom
When billing codes are enabled, a prompt appears that asks the user to enter the billing code for an outgoing fax.
The range varies by location. The factory default is 2 rings.
Default
Custom
Default
Custom
(default)
(default)
The range is between 1 and 16 digits. The default is 1 digit.
Use this feature to specify the number of rings that must occur before the fax modem answers.
This setting is used to adjust for some PBX ring signals. Change this setting only when directed by an HP technical support agent.
This setting should be left at the default value and only changed when directed by an HP technical support agent. Adjustment procedures associated with this setting are beyond the scope of this guide.
Set the volume for the fax ring-tone.
Off
Low (default)
High
Type the fax number to add.
Select a fax number to remove.
No (default)
Use this feature to add or delete numbers from the blocked fax list. The blocked fax list can contain up to 30 numbers. When the device receives a call from one of the blocked fax numbers, it deletes the incoming fax. It also logs the blocked fax in the activity log along with job-accounting information.
Yes
38 Chapter 2 Control panel ENWW
E-mail Setup
Administration > Initial Setup > E-mail Setup
Use this menu to enable the e-mail feature and to configure basic e-mail settings.
NOTE: To configure advanced e-mail settings, use the embedded Web server. For more information, see
Embedded Web server on page 178 .
Table 2-13 E-mail Setup menu
Menu item Values Description
Address Validation
Find Send Gateways
SMTP Gateway
Test Send Gateway
On (default)
Off
Enter a value.
This option enables the device to check e-mail syntax when you type an e-mail address. Valid e-mail addresses require the "@" sign and a ".".
Search the network for SMTP gateways that the device can use to send e-mail.
Specify the IP address of the SMTP gateway that is used to send email from the device.
Test the configured SMTP gateway to see if it is functional.
Send Setup menu
Administration > Initial Setup > Send Setup
Table 2-14 Send Setup menu
Menu item Values
Fax Number Confirmation Disable (default)
Enable
Description
When fax number confirmation is enabled, you are prompted to enter the fax number twice to verify that it has been typed correctly.
ENWW Initial Setup menu 39
Device Behavior menu
Administration > Device Behavior
Table 2-15 Device Behavior menu
Menu item Sub-menu item Sub-menu item
Language
Key Press Sound
Inactivity Timeout
Warning/Error
Behavior
Clearable Warnings
Continuable Events
Jam Recovery
Values Description
Select the language from the list.
On
Off
(default)
Select a different language for control-panel messages. When you select a new language, the keyboard layout might also change.
Use this feature to specify whether you hear a sound when you touch the screen or press buttons on the control panel.
Type a value between 10 and 300 seconds. The factory default is 60 seconds.
Specify the amount of time that elapses between any activity on the control panel and the device resetting to the default settings.
On
Job (default)
Set the amount of time that a clearable warning appears on the control panel.
Auto continue (10 seconds) (default)
Configure the device behavior when the device encounters certain errors.
Touch OK to continue
Auto (default)
Off
On
Configure how the device handles pages that are lost during a jam.
40 Chapter 2 Control panel ENWW
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item Sub-menu item
Tray Behavior Use Requested Tray
Manually Feed
Prompt
PS Defer Media
Use Another Tray
Size/Type Prompt
Duplex Blank Pages
Image Rotation
Values Description
Exclusively (default) Control how the device handles jobs that have specified a specific input tray.
First
Always (default)
Unless Loaded
Enabled
Disabled
(default)
Enabled (default)
Specify how a prompt should appear when the type or size for a job does not match the specified tray and the device pulls from the multipurpose tray instead.
Select either the PostScript (PS) or HP paper-handling model.
Disabled
Display (default)
Do not display
Auto (default)
Yes
Left to Right
Right to Left
Turn on or off the control-panel prompt to select another tray when the specified tray is empty.
Control whether the tray configuration message appears whenever a tray is opened or closed.
Control how the device handles two-sided jobs (duplexing).
Alternate
Image rotation allows users to put paper in the input tray using the same orientation regardless of whether there is a finisher installed.
NOTE: The image rotation set in this menu will be applied any time a job does not request stapling or when the requested stapling could not be applied because of unsupported media or when the stapler is unavailable.
Select Left to Right to rotate the image as if it were going to be bound on the left. This setting is appropriate for print jobs where reading from left to right is the cultural norm.
This is the default setting.
Select Right to Left to rotate the image as if it were going to be bound on the right. This setting is usually appropriate for print jobs where reading from right to left is the cultural norm.
Select Alternate to use a different loading orientation that might work better with preprinted forms that are used on legacy products.
ENWW Device Behavior menu 41
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item Sub-menu item
Operation Mode Multifunc Finisher or
MBM-3 Bin Stapler
Staples
Staples Out
Offset
A4/Letter Staple
Values
Mailbox
Stacker
Function Separator
Description
This menu appears when the HP 3-bin
Stapler/Stacker Accessory or the HP Booklet
Maker/Finisher Accessory is attached.
Allows you to set the default operation mode.
Mailbox assigns a user or group of users to each output bin. Stacker treats all of the output bins as a single large bin. When one bin gets full, jobs are automatically routed to the next bin. Function Separator specifies a default bin for specific types of jobs such as faxes or copies (stapler/stacker only).
Sets the default staple selection for documents sent to the device when no staple value is specified.
None
One Left Angled
One Right Angled
Two Left
Two Right
Two Top
Stop
Continue
Off
On
Normal
Alternate 1
Alternate 2
Sets the default behavior when a job specifies stapling and the stapler is out of staples. Stop stops printing if the stapler runs out of staples. Continue allows a job to continue printing even when the device is out of staples.
Turns the job offset feature on or off. When job offset is on, each copy of a job is shifted to one side in the output bin in order to keep each copy separate from the others.
Controls the speed of the print engine to prevent paper jams by using the stapler buffer.
NOTE: The stapler buffer may or may not be used depending on the selected media type or on the sensed media type, if
Autosense Mode is enabled.
If the Normal setting is enabled, the engine speed will be normal by using the stapler buffer whenever possible.
If the Alternate 1 setting is enabled, and the engine is in Autosense Mode, the engine slows down to prevent jams. If the product is
NOT in Autosense Mode, the engine performs at normal speed, using the stapler buffer whenever possible.
If the Alternate 2 setting is enabled, the engine always slows down to prevent jams, never using the stapler buffer.
42 Chapter 2 Control panel ENWW
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item Sub-menu item
Fold LTR-R & A4 - R
Values
–0.5 mm
0.0 mm
0.5 mm
1.0 mm
1.5 mm
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
–4.0 mm
–3.5 mm
–3.0 mm
–2.5 mm
–2.0 mm
–1.5 mm
–1.0 mm
Description
Adjusts the fold line for Letter and A4 size paper (booklet maker only).
ENWW Device Behavior menu 43
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item Sub-menu item
Fold Legal & JISB4
Values
–0.5 mm
0.0 mm
0.5 mm
1.0 mm
1.5 mm
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
–4.0 mm
–3.5 mm
–3.0 mm
–2.5 mm
–2.0 mm
–1.5 mm
–1.0 mm
Description
Adjusts the fold line for Legal and JIS B4 size paper (booklet maker only).
44 Chapter 2 Control panel ENWW
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item Sub-menu item
Fold 11X17 & A3
General Copy
Behavior
Scan Ahead
Auto Print Interrupt
Copy Interrupt
Alternative
Letterhead Mode
Values
–4.0 mm
–3.5 mm
–3.0 mm
–2.5 mm
–2.0 mm
–1.5 mm
–1.0 mm
–0.5 mm
0.0 mm
0.5 mm
1.0 mm
1.5 mm
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
Enabled (default)
Disabled
Description
Adjusts the fold line for Legal and 11x17 and
A3 size paper (booklet maker only).
Enabled
Disabled (default)
Enabled
Disabled (default)
Off
On
(default)
Turn on no-wait scanning. With Scan Ahead enabled, the pages in the original document are scanned to disk and held until the device becomes available.
When this feature is enabled, copy jobs can interrupt print jobs that are set to print multiple copies.
The copy job is inserted into the print queue at the end of one copy of the print job. After the copy job is complete, the device continues printing the remaining copies of the print job.
When this feature is enabled, a copy job that is currently printing can be interrupted when a new copy job is started. You are prompted to confirm that you want to interrupt the current job.
This option allows loading of letterhead or preprinted paper the same way for all copy jobs, whether copying to one side of the paper or to both sides of the paper.
ENWW Device Behavior menu 45
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item Sub-menu item
General Printing
Behavior
Override A4/Letter
Manual Feed
Courier Font
Wide A4
Print PS Errors
Print PDF Errors
Personality
Values
No
Yes (default)
Enabled
Disabled (default)
Regular (default)
Dark
Enabled
Disabled (default)
Enabled
Disabled (default)
Enabled
Disabled (default)
Auto (default)
PCL
PS
Description
When this feature is enabled, the job prints on letter-size paper when an A4 job is sent but no A4-size paper is loaded in the device
(or prints on A4 paper when a letter-size job is sent but no letter-size paper is loaded).
This option also overrides A3 with ledger-size paper and ledger with A3-size paper.
When this feature is enabled, the user can select manual feed from the control panel as the paper source for a job.
Select which version of the Courier font you want to use.
Change the printable area of A4-size paper.
If you enable this option, eighty 10-pitch characters can be printed on a single line of
A4 paper.
Select whether a PostScript (PS) error page is printed when the device encounters a PS error.
Select whether a PDF error page is printed when the device encounters a PDF error.
Select the printer language that the device should use.
Normally, you should not change the language.
If you change the setting to a specific language, the device does not automatically switch from one language to another unless specific software commands are sent to the device.
46 Chapter 2 Control panel ENWW
Table 2-15 Device Behavior menu (continued)
Menu item Sub-menu item
PCL
Sub-menu item
Form Length
Orientation
Font Source
Font Number
Font Pitch
Symbol Set
Append CR to LF
Suppress Blank
Pages
Media Source
Mapping
Values
Type a value between 5 and 128 lines. The factory default is 60 lines.
Portrait (default)
Landscape
Type a value between 0.44 and
99.99. The factory default is 10.00.
PC-8 (default)
(50 additional symbol sets from which to choose)
No (default)
Yes
No (default)
Yes
Standard
Classic
(default)
Description
PCL is a set of printer commands that
Hewlett-Packard developed to provide access to printer features.
Select the source from the list.
Type the font number. The range is between 0 and
999. The factory default is 0.
Select the orientation that is most often used for print jobs. Select Portrait if the short edge is at the top or Landscape if the long edge is at the top.
Select the font source for the user-soft default font.
Specify the font number for the user soft default font by using the source that is specified in the Font Source menu item. The device assigns a number to each font and lists it on the PCL font list (available from the
Administration menu).
If Font Source and Font Number indicate a contour font, use this feature to select a default pitch (for a fixed-spaced font).
Select any one of several available symbol sets from the control panel. A symbol set is a unique grouping of all the characters in a font.
Configure whether a carriage return (CR) is appended to each line feed (LF) encountered in backwards-compatible PCL jobs (pure text, no job control).
This option is for users who are generating their own PCL, which could include extra form feeds that cause blank pages to be printed. When Yes is selected, form feeds are ignored if the page is blank.
Select and maintain input trays by number when you are not using the device driver, or when the software program has no option for tray selection.
ENWW Device Behavior menu 47
Print Quality menu
Administration > Print Quality
Table 2-16 Print Quality menu
Menu item Sub-menu item
Adjust Color Highlights
Set Registration
Print Modes
Midtones
Shadows
Restore Color Values
Test Page
Source
Adjust Tray <X>
<Paper Type>
Values Description
Cyan Density . Magenta
Density . Yellow Density .
Black Density
+5 to –5 . Default is 0 .
Cyan Density . Magenta
Density . Yellow Density .
Black Density
+5 to –5 . Default is 0 .
Cyan Density . Magenta
Density . Yellow Density .
Black Density
Adjust the darkness or lightness of highlights on a printed page. Lower values represent lighter highlights on a printed page, and higher values represent darker highlights on a printed page.
Adjust the darkness or lightness of midtones on a printed page. Lower values represent lighter midtones on a printed page, and higher values represent darker midtones on a printed page.
Adjust the darkness or lightness of shadows on a printed page. Lower values represent lighter shadows on a printed page, and higher values represent darker shadows on a printed page.
+5 to –5 . Default is 0 .
Sets all the density values back to the factory default settings.
Shift the margin alignment to center the image on the page from top to bottom and from left to right. You can also align the image on the front with the image printed on the back.
All trays
Print a test page for setting the registration.
Select the source input tray for printing the Set
Registration page.
Tray <X>: <contents>
(choose a tray)
Shift from -20 to 20 along the X or Y axes. 0 is the default.
X1 Shift
Perform the alignment procedure for each tray.
When it creates an image, the device page from side to side as the sheet feeds from top to bottom into the device.
scans across the
X2 Shift
Y Shift
The scan direction is referred to as X. X1 is the scan direction for the first side of a 2-sided page. X2 is the scan direction for the second side of a 2-sided page.
The feed direction is referred to as Y.
Configure which mode is associated with which paper type.
48 Chapter 2 Control panel ENWW
Table 2-16 Print Quality menu (continued)
Menu item Sub-menu item
Auto Sense Mode Tray 1 sensing
Optimize
Tray 2-5 Sensing
Paper Curl
Pre-rotation
Fuser Temp
Tray 1
Gloss Mode
Values
Full Sensing (default for
Tray 1)
Expanded Sensing
(default for Trays 2-5)
Transparency Only
Expanded Sensing
Transparency Only
(default)
Normal
Reduced
Off
On
(default)
Normal (default)
Alternate 1
Alternate 2
Alternate 3
Normal
High
(default)
Alternate
Normal (default)
Description
When Full Sensing is selected, the product recognizes light, plain, heavy, glossy, and tough paper and overhead transparencies. When Expanded Sensing is selected, the device recognizes normal paper, overhead transparencies, glossy paper, and tough paper. When Transparency Only is selected, the device recognizes only overhead transparency and nonoverhead transparency types.
When Expanded Sensing is selected, the device recognizes normal paper, overhead transparencies, glossy paper, and tough paper. When Transparency
Only is selected, the device recognizes only overhead transparency and non-overhead transparency types.
To help reduce paper curl, set this option to Reduced .
This decreases full speed to 10 PPM (instead of 40 ppm) and 3/4 speed to 7.5 ppm (instead of 30 ppm).
Turn this feature On if horizontal streaks appear on pages. Using this feature increases the warm-up time for the device.
If you are seeing a faint image of the page repeated at the bottom of the page or on the following page, you should first make sure the Paper Type and Print Mode settings are correct for the type of paper you are using.
If you continue to see ghost images on your print jobs, set the Fuser Temp feature to one of the Alternate settings . Try the Alternate 1 setting first and see if it solves the problem. If you continue to see the problem, try Alternate 2 and then Alternate 3. With the Alternate
2 and Alternate 3 settings you may see an extra delay between jobs.
If you are seeing marks on the back side of the paper when printing from Tray 1, set the mode to Alternate .
This increases the frequency of the cleaning cycle.
Chosen when stable high gloss is required. Set this feature to High for glossy print jobs, such as photos, if you notice the gloss finish decreasing after the first page is printed. This setting reduces the performance for all paper types.
ENWW Print Quality menu 49
Table 2-16 Print Quality menu (continued)
Menu item Sub-menu item
Light Media
Values
Auto (default)
On
Environment Normal (default)
Low Temp
Line Voltage
Cleaning frequency
Normal (default)
100V
Normal (default)
Alternate
Resolution
Color REt
D-Blade bias
Waste Bin
Discharge Brush
Background
Heavy Mode
Tracking Control
Restore Optimize
Image REt 4800
1200X600dpi
Normal (default)
Alternate
Normal (default)
Alternate
Off (default)
On
Off (default)
On
30 PPM (default)
24 PPM
Off (default)
On
Enabled (default)
Disabled
Description
Prevents the fuser from wrapping with light paper. Set this feature to On if you are frequently seeing Fuser
Delay Jam or Fuser Wrap Jam messages, especially when printing on lightweight paper or on jobs with heavy toner coverage.
Optimizes performance in extreme low temperature environments. Set this feature to Low Temp if the product is operating in a low-temperature environment and you are having problems with print quality such as blisters in the printed image.
Optimizes performance in low-voltage conditions. Set this feature to 100V if the product is operating in a lowvoltage environment and you are having problems with print quality such as blisters in the printed image.
Set this feature to Alternate if you are seeing defects in the printed output that repeat at 38 mm (1.5 inch) intervals. This feature increases the frequency at which the C roller is cleaned. Setting this feature to
Alternate might also reduce printing speed and increase the frequency of consumable replacement.
Set this feature to Alternate if you are seeing short white vertical lines in the printed output. The Alternate setting might also cause dark spots in the printed output, so be sure to test this setting on a few print jobs.
Try setting this feature to Alternate if you are seeing lengthwise toner streaks in your printed output, especially in jobs with low toner coverage.
Enable this feature in low temperature and low humidity environments if you are seeing specks of toner scattered on double-sided jobs using light-weight paper and longer than ten pages.
Turn this feature On if pages are printing with a shaded background. Using this feature might reduce gloss levels.
The default setting is 30 PPM. Select the 24 PPM option to reduce the speed and improve fusing on heavy paper.
Improves color stability by adjusting the bias voltage.
This setting should remain On.
Select this setting to return all the settings in the
Optimize menu to the factory default settings.
Select Image REt 4800 to produces fast, high-quality printing that is appropriate for most print jobs
Select 1200X600dpi to produce the highest-quality printing available, but it may slow print speed. This setting may be useful for jobs that contain very thin lines or fine graphics.
Enable or disable Resolution Enhancement technology
(REt), which produces print output with smooth angles, curves, and edges.
50 Chapter 2 Control panel ENWW
Table 2-16 Print Quality menu (continued)
Menu item Sub-menu item
Calibration/Cleaning
Process Cleaning Page
Values
Process
Quick Calibration
Full Calibration
Delay Calibration At
Wake/Power On
Calibrate
Calibrate
No
Yes (default)
Description
Use this feature to create and process a cleaning page for cleaning excess toner off the pressure roller in the fuser. The process takes up to 2.5 minutes.
Performs partial product calibrations.
Performs all product calibrations.
This menu controls the timing of the calibration when the printer wakes up or is turned on.
● Select No to have the printer calibrate immediately when it wakes up or is turned on. The device will not print any jobs until it finishes calibrating.
● Select Yes to enable a device that is asleep to accept print jobs before it calibrates. The device only accepts new jobs for a short time. It may start calibrating before it has printed all the jobs it has received.
NOTE: For the best results, allow the device to calibrate before printing. Print jobs performed before calibration may not be of the highest quality.
ENWW Print Quality menu 51
Troubleshooting menu
Administration > Troubleshooting
NOTE: Many of the menu items under the Troubleshooting menu are for advanced troubleshooting purposes.
Table 2-17 Troubleshooting menu
Menu item Sub-menu item Sub-menu item Values Description
Event Log
Calibrate Scanner
PQ Troubleshooting
Fax T.30 Trace
Fax Transmit Signal
Loss
Fax V.34
Fax Speaker Mode
Diagnostic Page
Print T.30 Report
When to Print Report
Calibrate
Never auto print
(default)
Print after any fax job
Print after fax send jobs
This shows the event codes and their corresponding engine cycles on the controlpanel display.
Use this feature to compensate for offsets in the scanner imaging system (carriage head) for ADF and flatbed scans.
You might need to calibrate the scanner if it is not capturing the correct sections of scanned documents.
Print various diagnostic pages that help solve print-quality problems.
Print or configure the fax T.30 trace report. T.
30 is the standard that specifies handshaking, protocols, and error correction between fax machines.
Print after any fax error
Print after send errors only
Print after receive errors only
A value between 0 and 30. The default is
0.
Set loss levels to compensate for phone-line signal loss. Do not modify this setting unless requested to do so by an HP service representative because it could cause the fax to stop functioning.
Normal (default) Disable V.34 mode if several fax failures have occurred or if phone line conditions require it.
Off
Normal (default)
Diagnostic
A technician can use this feature technician to evaluate and diagnose fax issues by listening to the sounds of fax modulations.
Print a diagnostic page that includes color swatches and the EP parameters table.
52 Chapter 2 Control panel ENWW
Table 2-17 Troubleshooting menu (continued)
Menu item Sub-menu item Sub-menu item
Disable Cartridge
Check
Paper Path Sensors
Paper Path Test Test Page
Source
Destination
Duplex
Copies
Values Description
Use this item to enter a mode where a cartridge (or color pair of cartridge and drum) can be removed to determine which particular color is the source of a problem. In this mode, all consumable-related errors are ignored.
Initiate a test of the paper-path sensors.
Generate a test page for testing the paperhandling features. Define the path for the test in order to test specific paper paths.
Specify whether the test page is printed from all trays or from a specific tray.
All trays
Tray 1
Tray 2
(Additional trays are shown, if applicable.)
All bins
Off (default)
Select the output option for the test page.
Send the test page to all output bins or only to a specific bin.
Select whether the duplexer should be included in the test.
On
Range: 1-500,
Default is 1.
Select how many pages should be sent from the specified source as part of the test.
ENWW Troubleshooting menu 53
Table 2-17 Troubleshooting menu (continued)
Menu item Sub-menu item Sub-menu item
Finishing Paper Path
Test
Staples Finishing Options
Stack
Destination Bin
Media Size
Media Type
Copies
Duplex
Test Page
Destination Bin
Media Size
Media Type
Copies
Duplex
Test Page
Values Description
50
100
500
Off
On
Legal
A4
Executive (JIS)
8.5 x 13
Select from a list of bins.
1
10
Choose from a list of available options.
Test the paper-handling features on the finisher.
Letter
Select the option that you want to test.
Select the paper size for the test.
A4
Select from a list of types.
Range: 2-30,
Default=2
Off
On
Select from a list of bins.
Letter
Select the paper type for the test.
Select the number of copies to include in the test.
Select whether to use the duplexer in the test.
Print a test page to use for the test.
Select the options that you want to use to test the stacker.
Select the type of media to use for the
Finishing Paper Path Test.
Select the number of copies to include in the
Finishing Paper Path Test.
Select whether to use the duplexer in the
Finishing Paper Path Test.
Print a test page to use for the test.
54 Chapter 2 Control panel ENWW
Table 2-17 Troubleshooting menu (continued)
Menu item Sub-menu item Sub-menu item
Booklet Maker Media Size
Manual Sensor Test
Media Type
Copies
Duplex
Test Page
Values
100
500
Off
On
Letter
Legal
A4
Executive (JIS)
8.5 x 13
Select from a list of bins.
1
10
50
Description
Select the options that you want to use to test the booklet maker.
Select the type of media to use for the
Finishing Paper Path Test.
Select the number of copies to include in the
Finishing Paper Path Test.
Select whether to use the duplexer in the
Finishing Paper Path Test.
Print a test page to use for the test.
This item performs tests to determine whether the paper-path sensors are operating correctly.
ENWW Troubleshooting menu 55
Table 2-17 Troubleshooting menu (continued)
Menu item Sub-menu item Sub-menu item
Component Test
Values Description
Transfer Motors
Belt Only
Image Drum Motors
Black Laser Scanner
Exercise individual parts independently to isolate noise, leaking, or other issues. To start the test, select one of the components. The test runs the number of times specified in the
Repeat option. You might be prompted to remove parts from the device during the test.
Press the Stop button to abort the test.
Cyan Laser Scanner
Magenta Laser
Scanner
Yellow Laser
Scanner
Fuser Motor
Fuser Pressure
Release Motor
Black Alienation
Motor
Cyan Alienation
Motor
Magenta Alienation
Motor
Yellow Alienation
Motor
ITB Contact/
Alienation
Tray 2 Pickup Motor
Tray 2 Pickup
Solenoid
Tray 3 Pickup Motor
Tray 3 Pickup
Solenoid
Tray 4 Pickup Motor
Tray 4 Pickup
Solenoid
Tray 5 Pickup Motor
Tray 5 Pickup
Solenoid
Duplexer Reverse
Motor
Duplexer Feed Motor
Duplexer ReFeed
Motor
Paper Transport
Motor
56 Chapter 2 Control panel ENWW
Table 2-17 Troubleshooting menu (continued)
Menu item Sub-menu item Sub-menu item
Repeat
Print/Stop Test
Color Band Test Test Page
Copies
Scanner Tests
Control Panel
Finisher Tests
Lower Lamp
Sensors
ADF Input Motor
ADF Input Reverse
Flatbed Motor
ADF Read Motor
ADF Read Motor
Reverse
ADF Duplex
Solenoid
ADF LED Indicator
LEDs
Display
Buttons
Touchscreen
Manual Sensor Test
Component Test
Values
Once (Default)
Continuous
Continuous value from 0 to 60,000 milliseconds.
Default: 0
Continuous value from 1 to 30.
Default: 1
Description
Determines the number of times the test runs.
Isolate faults by stopping the device during the print cycle and observing where in the process the image degrades. To run the test, specify a stop time. The next job that is sent to the device stops at the specified time in the process.
Prints a page that helps identify arcing in the high-voltage power supplies.
Specify the number of copies to print for the
Color Band test
A service technician can use this menu item to diagnose potential problems with the device scanner.
Verify that the components of the control panel are functioning correctly.
ENWW Troubleshooting menu 57
Resets menu
Administration > Resets
Table 2-18 Resets menu
Menu item Values Description
Clear Local Address Book
Clear Fax Activity Log
Clear
Yes
Use this feature to clear all addresses from the address books that are stored on the device.
Use this feature to clear all events from the Fax Activity Log.
Restore Factory Settings
Reset Supplies
No (default)
Restore Factory Telecom Setting Restore Use this option to restore the following settings to their factory default settings: Transmit Signal Loss, V34, Maximum Baud Rate, Speaker
Mode.
Use this feature to restore all device settings to their factory defaults.
Restore
New Document Feeder Kit (Yes/
No)
Notify the device that a new document-feeder kit has been installed.
58 Chapter 2 Control panel ENWW
Service menu
Administration > Service
The Service menu is locked and requires a PIN for access. This menu is intended for use by authorized service personnel.
ENWW Service menu 59
60 Chapter 2 Control panel ENWW
3 Software for Windows
●
Supported operating systems for Windows
●
Supported printer drivers for Windows
●
HP Universal Print Driver (UPD)
●
Select the correct printer driver for Windows
●
●
Change printer-driver settings for Windows
●
Supported utilities for Windows
●
Software for other operating systems
ENWW 61
Supported operating systems for Windows
The product supports the following Windows operating systems:
● Windows XP (32-bit and 64-bit)
● Windows Server 2003 (32-bit and 64-bit)
● Windows Server 2008 (32-bit and 64-bit)
● Windows 2000
● Windows Vista (32-bit and 64-bit)
62 Chapter 3 Software for Windows ENWW
Supported printer drivers for Windows
HP provides the following drivers for downloading:
● HP Universal Print Driver (UPD): Postscript, PCL 6, PCL 5
● Mac Driver
● Linux
● SAP
● UNIX Model Script
Drivers for this product are available at www.hp.com/go/cljcm6049mfp_software or your country/region alternative.
The printer drivers include online Help that has instructions for common printing tasks and also describes the buttons, checkboxes, and drop-down lists that are in the printer driver.
NOTE: For more information about the UPD, see www.hp.com/go/upd .
ENWW Supported printer drivers for Windows 63
HP Universal Print Driver (UPD)
The HP Universal Print Driver (UPD) for Windows is a single driver that gives you instant access to virtually any HP LaserJet product, from any location, without downloading separate drivers. It is built on proven HP print driver technology and has been tested thoroughly and used with many software programs. It is a powerful solution that performs consistently over time.
The HP UPD communicates directly with each HP product, gathers configuration information, and then customizes the user interface to show the product’s unique, available features. It automatically enables features that are available for the product, such as two-sided printing and stapling, so you do not need to enable them manually.
NOTE: For more information about the UPD, see www.hp.com/go/upd .
UPD installation modes
Traditional mode
Dynamic mode
● Use this mode if you are installing the driver for a single computer.
● When installed with this mode, UPD operates like traditional printer drivers.
● If you use this mode, you must install UPD separately for each computer.
● Use this mode if you are installing the driver for a mobile computer, so you can discover and print to HP products in any location.
● Use this mode if you are installing UPD for a workgroup.
● To use this mode, download UPD from the Internet. See www.hp.com/go/ upd , www.hp.com/go/cljcm6049mfp_software , or your country/region alternative.
64 Chapter 3 Software for Windows ENWW
Select the correct printer driver for Windows
Printer drivers provide access to the product features and allow the computer to communicate with the product (using a printer language). Check the installation notes and readme files for additional software and languages.
HP PCL 6 driver description
● Recommended for printing in all Windows environments
● Provides the overall best speed, print quality, and product-feature support for most users
● Developed to align with the Windows Graphic Device Interface (GDI) for the best speed in Windows environments
● Might not be fully compatible with third-party and custom software programs that are based on
PCL 5
HP postscript emulation description
● Recommended for printing with Adobe ® software programs or with other highly graphics-intensive software programs
● Provides support for printing from postscript level 3 emulation needs, or for postscript flash font support
● Performs slightly faster than the PCL 6 driver when using Adobe software programs
HP PCL 5 description
● Recommended for general office printing in Windows environments
● Compatible with previous PCL versions and older HP LaserJet products
● The best choice for printing from third-party or custom software programs
● The best choice when operating with mixed environments, which require the product to be set to
PCL 5 (UNIX, Linux, mainframe)
● Designed for use in corporate Windows environments to provide a single driver for use with multiple printer models
● Preferred when printing to multiple printer models from a mobile Windows computer
ENWW Select the correct printer driver for Windows 65
Priority for print settings
Changes to print settings are prioritized depending on where the changes are made:
NOTE: The names of commands and dialog boxes might vary depending on your software program.
● Page Setup dialog box : Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed here override settings changed anywhere else.
● Print dialog box : Click Print , Print Setup , or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed in the Print dialog box have a lower priority and do not override changes made in the Page Setup dialog box.
● Printer Properties dialog box (printer driver) : Click Properties in the Print dialog box to open the printer driver. Settings changed in the Printer Properties dialog box do not override settings anywhere else in the printing software.
● Default printer driver settings : The default printer driver settings determine the settings used in all print jobs, unless settings are changed in the Page Setup , Print , or Printer Properties dialog boxes.
● Printer control panel settings : Settings changed at the printer control panel have a lower priority than changes made anywhere else.
66 Chapter 3 Software for Windows ENWW
Change printer-driver settings for Windows
Change the settings for all print jobs until the software program is closed
Change the default settings for all print jobs
1.
On the File menu in the software program, click Print .
2.
Select the driver, and then click
Properties or Preferences .
The steps can vary; this procedure is most common.
1.
Windows XP, Windows Server
2003, and Windows Server 2008
(using the default Start menu view) : Click Start , and then click
Printers and Faxes .
-or-
Windows 2000, Windows XP,
Windows Server 2003, and
Windows Server 2008 (using the
Classic Start menu view) : Click
Start , click Settings , and then click
Printers .
-or-
Change the product configuration settings
1.
Windows XP, Windows Server
2003, and Windows Server 2008
(using the default Start menu view) : Click Start , and then click
Printers and Faxes .
-or-
Windows 2000, Windows XP,
Windows Server 2003, and
Windows Server 2008 (using the
Classic Start menu view) : Click
Start , click Settings , and then click
Printers .
-or-
Windows Vista : Click Start , click
Control Panel , and then in the category for Hardware and
Sound click Printer .
Windows Vista : Click Start , click
Control Panel , and then in the category for Hardware and
Sound click Printer .
2.
Right-click the driver icon, and then select Printing Preferences .
2.
Right-click the driver icon, and then select Properties .
3.
Click the Device Settings tab.
ENWW Change printer-driver settings for Windows 67
Supported utilities for Windows
HP Web Jetadmin
HP Web Jetadmin is a browser-based management tool for HP Jetdirect-connected printers within your intranet, and it should be be installed only on the network administrator’s computer.
NOTE: HP Web Jetadmin 10.0 or later is required for full support of this product.
To download a current version of HP Web Jetadmin and for the latest list of supported host systems, visit www.hp.com/go/webjetadmin .
When installed on a host server, any client can gain access to HP Web Jetadmin by using a supported
Web browser (such as Microsoft® Internet Explorer 4.x or Netscape Navigator 4.x or later) by navigating to the HP Web Jetadmin host.
Embedded Web server
The device is equipped with an embedded Web server, which provides access to information about device and network activities. This information appears in a Web browser, such as Microsoft Internet
Explorer, Netscape Navigator, Apple Safari, or Firefox.
The embedded Web server resides on the device. It is not loaded on a network server.
The embedded Web server provides an interface to the device that anyone who has a networkconnected computer and a standard Web browser can use. No special software is installed or configured, but you must have a supported Web browser on your computer. To gain access to the embedded Web server, type the IP address for the device in the address line of the browser. (To find the IP address, print a configuration page. For more information about printing a configuration page, see
.)
For a complete explanation of the features and functionality of the embedded Web server, see
Embedded Web server on page 178 .
68 Chapter 3 Software for Windows ENWW
Software for other operating systems
OS
UNIX
Linux
Software
For HP-UX and Solaris networks, go to www.hp.com/support/go/jetdirectunix_software to install model scripts using the HP Jetdirect printer installer (HPPI) for UNIX.
For the latest model scripts, go to www.hp.com/go/unixmodelscripts .
For information, go to www.hp.com/go/linuxprinting .
ENWW Software for other operating systems 69
70 Chapter 3 Software for Windows ENWW
4 Use the product with Macintosh
●
●
Use features in the Macintosh printer driver
ENWW 71
Software for Macintosh
Supported operating systems for Macintosh
The device supports the following Macintosh operating systems:
● Mac OS X V10.3, V10.4, V10.5 and later
NOTE: For Mac OS X V10.4 and later, PPC and Intel Core Processor Macs are supported.
Supported printer drivers for Macintosh
The HP installer provides PostScript ® Printer Description (PPD) files, Printer Dialog Extensions (PDEs), and the HP Printer Utility for use with Macintosh computers.
The PPDs, in combination with the Apple PostScript printer drivers, provide access to device features.
Use the Apple PostScript printer driver that comes with the computer.
Remove software from Macintosh operating systems
To remove the software from a Macintosh computer, drag the PPD files to the trash can.
Priority for print settings for Macintosh
Changes to print settings are prioritized depending on where the changes are made:
NOTE: The names of commands and dialog boxes might vary depending on your software program.
● Page Setup dialog box : Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed here might override settings changed anywhere else.
● Print dialog box : Click Print , Print Setup , or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed in the Print dialog box have a lower priority and do not override changes made in the Page Setup dialog box.
● Default printer driver settings : The default printer driver settings determine the settings used in all print jobs, unless settings are changed in the Page Setup , Print , or Printer Properties dialog boxes.
● Printer control panel settings : Settings changed at the printer control panel have a lower priority than changes made anywhere else.
72 Chapter 4 Use the product with Macintosh ENWW
Change printer-driver settings for Macintosh
Change the settings for all print jobs until the software program is closed
Change the default settings for all print jobs
Change the product configuration settings
1.
On the File menu, click Print .
2.
Change the settings that you want on the various menus.
1.
On the File menu, click Print .
Mac OS X V10.3 or Mac OS X V10.4
2.
Change the settings that you want on the various menus.
1.
From the Apple menu, click System
Preferences and then Print &
Fax .
3.
On the Presets menu, click Save as and type a name for the preset.
2.
Click Printer Setup .
These settings are saved in the
Presets menu. To use the new settings, you must select the saved preset option every time you open a program and print.
3.
Click the Installable Options menu.
Mac OS X V10.5
1.
From the Apple menu, click System
Preferences and then Print &
Fax .
2.
Click Options & Supplies .
3.
Click the Driver menu.
4.
Select the driver from the list, and configure the installed options.
Software for Macintosh computers
HP Printer Utility
Use the HP Printer Utility to set up product features that are not available in the printer driver.
You can use the HP Printer Utility when the product uses a universal serial bus (USB) cable or is connected to a TCP/IP-based network.
Open the HP Printer Utility
Open the HP Printer Utility in Mac OS X V10.3 and V10.4
1.
Open the Finder, click Applications , click Utilities , and then double-click Printer Setup Utility .
2.
Select the product that you want to configure, and then click Utility .
Open the HP Printer Utility in Mac OS X V10.5
From the Printer menu, click Printer Utility .
-or-
From the Print Queue , click the Utility icon.
HP Printer Utility features
The HP Printer Utility consists of pages that you open by clicking in the Configuration Settings list.
The following table describes the tasks that you can perform from these pages.
ENWW Software for Macintosh 73
Item
Configuration Page
Supplies Status
File Upload
Upload Fonts
Firmware Update
Duplex Mode
Economode & Toner Density
Resolution
Lock Resources
Stored Jobs
Trays Configuration
IP Settings
Bonjour Settings
Additional Settings
E-mail Alerts
Description
Prints a configuration page.
Shows the device supplies status.
Transfers files from the computer to the device.
Transfers font files from the computer to the device.
Transfers updated firmware files from the computer to the device.
Turns on the automatic two-sided printing mode.
Turns on the Economode setting to conserve toner, or adjusts toner density.
Changes the resolution settings, including the REt setting.
Locks or unlocks storage products, such as a hard disk.
Manages print jobs that are stored on the device hard disk.
Changes the default tray settings.
Changes the device network settings and provides access to the embedded Web server.
Provides the ability to turn on or off Bonjour support or change the device service name that is listed on a network.
Provides access to the embedded Web server.
Configures the device to send e-mail notices for certain events.
Supported utilities for Macintosh
Embedded Web server
The device is equipped with an embedded Web server, which provides access to information about device and network activities. For more information, see
Embedded Web server sections on page 179 .
74 Chapter 4 Use the product with Macintosh ENWW
Use features in the Macintosh printer driver
Create and use printing presets in Macintosh
Use printing presets to save the current printer driver settings for reuse.
Create a printing preset
1.
On the File menu, click Print .
2.
Select the driver.
3.
Select the print settings.
4.
In the Presets box, click Save As...
, and type a name for the preset.
5.
Click OK .
Use printing presets
1.
On the File menu, click Print .
2.
Select the driver.
3.
In the Presets box, select the printing preset that you want to use.
NOTE: To use printer-driver default settings, select Standard .
Resize documents or print on a custom paper size
You can scale a document to fit on a different size of paper.
1.
On the File menu, click Print .
2.
Open the Paper Handling menu.
3.
In the area for Destination Paper Size , select Scale to fit paper size , and then select the size from the drop-down list.
4.
If you want to use only paper that is smaller than the document, select Scale down only .
Print a cover page
You can print a separate cover page for your document that includes a message (such as “Confidential”).
1.
On the File menu, click Print .
2.
Select the driver.
3.
Open the Cover Page menu, and then select whether to print the cover page Before Document or After Document .
4.
In the Cover Page Type menu, select the message that you want to print on the cover page.
NOTE: To print a blank cover page, select Standard as the Cover Page Type .
ENWW Use features in the Macintosh printer driver 75
Use watermarks
A watermark is a notice, such as “Confidential,” that is printed in the background of each page of a document.
1.
On the File menu, click Print .
2.
Open the Watermarks menu.
3.
Next to Mode , select the type of watermark to use. Select Watermark to print a semi-transparent message. Select Overlay to print a message that is not transparent.
4.
Next to Pages , select whether to print the watermark on all pages or on the first page only.
5.
Next to Text , select one of the standard messages, or select Custom and type a new message in the box.
6.
Select options for the remaining settings.
Print multiple pages on one sheet of paper in Macintosh
You can print more than one page on a single sheet of paper. This feature provides a cost-effective way to print draft pages.
1.
On the File menu, click Print .
2.
Select the driver.
3.
Open the Layout menu.
4.
Next to Pages per Sheet , select the number of pages that you want to print on each sheet (1, 2,
4, 6, 9, or 16).
5.
Next to Layout Direction , select the order and placement of the pages on the sheet.
6.
Next to Borders , select the type of border to print around each page on the sheet.
76 Chapter 4 Use the product with Macintosh ENWW
Print on both sides of the page (duplex printing)
Use automatic duplex printing
1.
Insert enough paper into one of the trays to accommodate the print job. If you are loading special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper face-up with the bottom edge feeding into the printer first.
● For all other trays, load the letterhead paper face-down with the top edge at the back of the tray.
2.
On the File menu, click Print .
3.
Open the Layout menu.
4.
Next to Two-Sided , select either Long-Edge Binding or Short-Edge Binding .
5.
Click Print .
Print on both sides manually
1.
Insert enough paper into one of the trays to accommodate the print job. If you are loading special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper face-up with the bottom edge feeding into the printer first.
● For all other trays, load the letterhead paper face-down with the top edge at the back of the tray.
CAUTION: To avoid jams, do not load paper that is heavier than 105 g/m 2 (28-lb bond).
2.
On the File menu, click Print .
3.
On the Finishing menu, select Manually Print on 2nd Side .
4.
Click Print . Follow the instructions in the pop-up window that appears on the computer screen before replacing the output stack in tray 1 for printing the second half.
5.
Go to the printer, and remove any blank paper that is in tray 1.
6.
Insert the printed stack face-up with the bottom edge feeding into the printer first in tray 1. You must print the second side from tray 1.
7.
If prompted, press the appropriate control-panel button to continue.
Set the stapling options
If a finishing device that has a stapler is installed, you can staple documents.
1.
On the File menu, click Print .
2.
Open the Finishing menu.
3.
In the Stapling Options drop-down list, select the stapling option that you want to use.
ENWW Use features in the Macintosh printer driver 77
Store jobs
You can store jobs on the product so you can print them at any time. You can share stored jobs with other users, or you can make them private.
1.
On the File menu, click Print .
2.
Open the Job Storage menu.
3.
In the Job Storage: drop-down list, select the type of stored job.
4.
For the Stored Job , Private Job , and Private Stored Job types of stored jobs, enter a name for the stored job in the box next to Job Name: .
Select which option to use if another stored job already has that name.
● Use Job Name + (1 - 99) appends a unique number to the end of the job name.
● Replace Existing File overwrites the existing stored job with the new one.
5.
If you selected Stored Job or Private Job in step 3, type a 4-digit number in the box next to PIN
To Print (0000 - 9999) . When other people attempt to print this job, the product prompts them to enter this PIN number.
Set the color options
Use the Color Options pop-up menu to control how colors are interpreted and printed from software programs.
1.
On the File menu in the software program, click Print .
2.
Select the driver.
3.
Open the Color Options pop-up menu.
4.
Click Show Advanced Options .
5.
Adjust the individual settings for text, graphics, and photographs.
Use the Services menu
If the product is connected to a network, use the Services menu to obtain product and supply-status information.
1.
On the File menu, click Print .
2.
Open the Services menu.
78 Chapter 4 Use the product with Macintosh ENWW
3.
To open the embedded Web server and perform a maintenance task, do the following: a.
Select Device Maintenance .
b.
Select a task from the drop-down list.
c.
Click Launch .
4.
To go to various support Web sites for this device, do the following: a.
Select Services on the Web .
b.
Select Internet Services , and select an option from the drop-down list.
c.
Click Go!
.
ENWW Use features in the Macintosh printer driver 79
80 Chapter 4 Use the product with Macintosh ENWW
5 Connect the product
●
●
ENWW 81
USB connection
This product supports one USB 2.0 device connection. The USB port is located on the back of the product. You must use an A-to-B type USB cable that is no longer than 2 meters (6.56 feet). The USB
2.0 port can be used to connect directly to the product and to upgrade firmware.
Figure 5-1 USB connection
1 USB 2.0 port
82 Chapter 5 Connect the product ENWW
Network connection
All product models include an embedded HP Jetdirect print server, which supports connection to a network using the local area network (LAN) connector (RJ-45) on the back of the product. For more
information about configuring the product on a network see Network configuration on page 85
Figure 5-2 Network connection
1
2
Network cable
Network port
ENWW Network connection 83
84 Chapter 5 Connect the product ENWW
6 Network configuration
●
Benefits of a network connection
●
●
●
ENWW 85
Benefits of a network connection
Connecting the product to a network provides a number of benefits:
● All network users can share the same product.
● You can manage the product remotely, from any computer on the network, by using the embedded
Web server (EWS).
● For large enterprise businesses, you can also manage the product remotely by using HP Web
Jetadmin.
86 Chapter 6 Network configuration ENWW
Supported network protocols
The product supports the TCP/IP network protocol, the most widely used and accepted networking protocol. Many networking services utilize this protocol. For more information, see
TCP/IP on page 88 . The following table lists the supported networking services and protocols.
Table 6-1 Printing
Service name Description port9100 (Direct Mode)
Line printer daemon (LPD)
Printing service
Printing service
Table 6-2 Network device discovery
Service name
SLP (Service Location Protocol)
Bonjour
Description
Device-discovery protocol, used to help find and configure network devices. Used primarily by Microsoft-based programs.
Device-discovery protocol, used to help find and configure network devices. Used primarily by Apple Macintosh-based programs.
Table 6-3 Messaging and management
Service name
HTTP (Hyper Text Transfer Protocol)
EWS (embedded Web server)
SNMP (Simple Network Management Protocol)
Description
Allows Web browsers to communicate with embedded Web server.
Allows a user to manage the product through a Web browser.
Used by network applications for product management. SNMP v1 and standard MIB-II (Management Information Base) objects are supported.
Table 6-4 IP addressing
Service name
DHCP (Dynamic Host Configuration Protocol)
BOOTP (Bootstrap Protocol)
Auto IP
Description
For automatic IP address assignment. The DHCP server provides the product with an IP address. Generally, no user intervention is required for the product to obtain an IP address from a DHCP server.
For automatic IP address assignment. The BOOTP server provides the product with an IP address. Requires the administrator to input a product's MAC hardware address on the BOOTP server for the product to obtain an IP address from that server.
For automatic IP address assignment. If neither a DHCP server nor a BOOTP server is present, the product uses this service to generate a unique IP address.
ENWW Supported network protocols 87
Configuring network settings
You might need to configure certain network parameters on the product. You can configure these parameters from the installation software, the product control panel, the embedded Web server, or management software, such as HP Web Jetadmin.
For more information about supported networks and network configuration tools, see the HP Jetdirect
Print Servers Administrator’s Guide . The guide comes with printers in which an HP Jetdirect print server is installed.
TCP/IP
Similar to a common language that people use to communicate with each other, TCP/IP (Transmission
Control Protocol/Internet Protocol) is a suite of protocols designed to define the way computers and other devices communicate with each other over a network.
Internet Protocol (IP)
When information is sent across the network, the data is broken down into small packets. Each packet is sent independently. Each packet is encoded with IP information, such as the IP address of the sender and receiver. IP packets can be routed over routers and gateways: devices that connect a network with other networks.
IP communications require no connection. When IP packets are sent, they might not arrive at their destination in the correct sequence. However, higher-level protocols and programs place the packets in the correct sequence, so IP communications are efficient.
Each node or device that communicates on the network requires an IP address.
Transmission Control Protocol (TCP)
TCP breaks the data into packets and recombines them on the receiving end by providing a connectionoriented, reliable, and guaranteed delivery service to another node on the network. When data packets are received at their destination, TCP calculates a checksum for each packet to verify that the data is not corrupt. If the data in the packet has been corrupted during transmission, TCP discards the packet and requests that the packet be resent.
IP address
Every host (workstation or node) on an IP network requires a unique IP address for each network interface. This address is used to identify both the network and specific hosts that are located on that network. It is possible for a host to query a server for a dynamic IP address each time the product boots up (for example, using DHCP and BOOTP).
An IP address contains four bytes of information, divided into sections that each contain one byte. The
IP address has the following format: xxx.xxx.xxx.xxx
CAUTION: When assigning IP addresses, always consult the IP address administrator. Setting the wrong address can disable other equipment operating on the network or interfere with communications.
Configure IP parameters
TCP/IP configuration parameters can be configured manually, or they can be automatically downloaded by using DHCP or BOOTP each time the product is turned on.
88 Chapter 6 Network configuration ENWW
When turned on, a new product that is unable to retrieve a valid IP address from the network automatically assigns itself a default IP address. The IP address for the product is listed on the product
Configuration page and the Network report. See
Information pages on page 176 .
Dynamic Host Configuration Protocol (DHCP)
DHCP allows a group of devices to use a set of IP addresses that are maintained by a DHCP server.
The product sends a request to the server, and if an IP address is available, the server assigns it to that product.
BOOTP
BOOTP is a bootstrap protocol used to download configuration parameters and host information from a network server.
The client broadcasts a boot request packet that contains the product hardware address. The server answers with a boot reply packet that contains the information that the product needs for configuration.
Subnets
When an IP network address for a particular network class is assigned to an organization, no provision is made for more than one network being present at that location. Local network administrators use subnets to partition a network into several different subnetworks. Splitting a network into subnets can result in better performance and improved use of limited network address space.
Subnet mask
The subnet mask is a mechanism used to divide a single IP network into several different subnetworks.
For a given network class, a portion of an IP address that would normally be used to identify a node is used, instead, to identify a subnetwork. A subnet mask is applied to each IP address to specify the portion used for subnetworks, and the portion used to identify the node.
Gateways
Gateways (routers) are used to connect networks together. Gateways are devices that act as translators between systems that do not use the same communication protocols, data formatting, structures, languages, or architectures. Gateways repackage the data packets and change the syntax to match that of the destination system. When networks are divided into subnets, gateways are required to connect one subnet to another.
Default gateway
The default gateway is the IP address of the gateway or router that moves packets between networks.
If multiple gateways or routers exist, then the default gateway is typically the address of the first, or nearest, gateway or router. If no gateways or routers exist, then the default gateway will typically assume the IP address of the network node (such as the workstation or product).
ENWW Configuring network settings 89
Configure TCP/IPv4 parameters
If your network doesn't provide automatic IP addressing through DHCP, BOOTP, RARP, or another method, you might need to enter the following parameters manually before you can print over the network:
● IP address (4 bytes)
● Subnet mask (4 bytes)
● Default gateway (4 bytes)
Input or change the IP address
You can view the current IP address of the device from the control-panel Home screen by touching
Network Address .
Use the following procedure to change the IP address manually.
1.
Scroll to and touch Administration .
2.
Scroll to and touch Initial Setup .
3.
Touch Networking and I/O .
4.
Touch Embedded Jetdirect .
5.
Touch TCP/IP .
6.
Touch IPV4 Settings .
7.
Touch Config Method .
8.
Touch Manual .
9.
Touch Save .
10.
Touch Manual Settings .
11.
Touch IP Address .
12.
Touch the IP Address text box.
13.
Use the touchscreen keypad to type the IP address.
14.
Touch OK .
15.
Touch Save .
Set the subnet mask
1.
Scroll to and touch Administration .
2.
Scroll to and touch Initial Setup .
3.
Touch Networking and I/O .
4.
Touch Embedded Jetdirect .
5.
Touch TCP/IP .
90 Chapter 6 Network configuration ENWW
6.
Touch IPV4 Settings .
7.
Touch Config Method .
8.
Touch Manual .
9.
Touch Save .
10.
Touch Manual Settings .
11.
Touch Subnet Mask .
12.
Touch the Subnet Mask text box.
13.
Use the touchscreen keypad to type the subnet mask.
14.
Touch OK .
15.
Touch Save .
Set the default gateway
1.
Scroll to and touch Administration .
2.
Scroll to and touch Initial Setup .
3.
Touch Networking and I/O .
4.
Touch Embedded Jetdirect .
5.
Touch TCP/IP .
6.
Touch IPV4 Settings .
7.
Touch Config Method .
8.
Touch Manual .
9.
Touch Save .
10.
Touch Manual Settings .
11.
Touch Default Gateway .
12.
Touch the Default Gateway text box.
13.
Use the touchscreen keyboard to type the default gateway.
14.
Touch OK .
15.
Touch Save .
Configure TCP/IPv6 parameters
For information about configuring the device for a TCP/IPv6 network, see the HP Jetdirect Print Servers
Administrator's Guide .
ENWW Configuring network settings 91
Network utilities
The product can be used with several utilities that make it easy to monitor and manage the product on a network.
● HP Web Jetadmin: See
●
Embedded Web server: See Embedded Web server on page 68
.
Other components and utilities
Windows
● Software installer — automates the printing system installation
● Online Web registration
Macintosh OS
● The HP Printer Utility — change device settings, view status, and set up printer-event notification from a Mac.
This utility is supported for Mac OS X V10.3 and later.
92 Chapter 6 Network configuration ENWW
7 Paper and print media
●
Understand paper and print media use
●
Supported paper and print media sizes
●
●
Special paper or print media guidelines
●
●
●
ENWW 93
Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this user guide. Paper or print media that does not meet these guidelines might cause the following problems:
● Poor print quality
● Increased jams
● Premature wear on the product, requiring repair
For best results, use only HP-brand paper and print media designed for laserjets or multiuse. Do not use paper or print media made for inkjet printers. Hewlett-Packard Company cannot recommend the use of other brands of media because HP cannot control their quality.
It is possible for paper to meet all of the guidelines in this user guide and still not produce satisfactory results. This might be the result of improper handling, unacceptable temperature and/or humidity levels, or other variables over which Hewlett-Packard has no control.
CAUTION: Using paper or print media that does not meet Hewlett-Packard's specifications might cause problems for the product, requiring repair. This repair is not covered by the Hewlett-Packard warranty or service agreements.
94 Chapter 7 Paper and print media ENWW
Supported paper and print media sizes
NOTE: To obtain best print results, select the appropriate paper size and type in your print driver before printing.
Table 7-1 Supported paper and print media sizes
Size Dimensions Tray 1 Tray 2 Trays 3, 4, 5
Letter 216 x 279 mm (8.5 x 11 in)
Letter Rotated 279 x 216 mm (11 x 8.5 in)
Legal
A4
A4 Rotated
216 x 356 mm (8.5 x 14 in)
210 x 297 mm (8.27 x 11.69 in)
297 x 210 mm (11.69 x 8.27 in)
Executive
Statement
8.5 x 13
A3
A5
A6
11 x 17
12 x 18
184 x 267 mm (7.24 x 10.51 in)
139.7 x 215.9 mm (5.5 x 8.5 in)
216 x 330 mm (8.5 x 13 in)
297 x 420 mm (11.69 x 16.54 in)
148 x 210 mm (5.83 x 8.27 in)
105 x 148 mm (4.13 x 5.83 in)
279 x 432 mm (11 x 17 in)
305 x 457 mm (12 x 18 in)
B4 (JIS)
RA3
SRA3
B5 (JIS)
257 x 364 mm (10.12 x 14.33 in)
305 x 430 mm (12 x 16.93 in)
320 x 450 mm (12.6 x 17.7 in)
182 x 257 mm (7.17 x 10.12 in)
8k
16k
270 x 390 mm (10.63 x 15.35 in)
195 x 270 mm (7.68 x 10.63 in)
Custom
Custom
98.55 x 139.70 mm to 320 x 457.2 mm
(3.9 x 5.5 to 12.6 x 18 in)
148 x 210 mm to 297 x 432 mm (5.8 x 8.2 to
11.7 x 17 in)
1
2
3
Custom 148 x 210 mm to 320 x 457.2 mm (5.8 x 8.2 to
12.6 x 18 in)
Tray automatically detects paper size.
Standard sizes within the custom range for Tray 2 are: 8.5 x 13, RA4, SRA4, 8K (270 x 390), 16K (195 x 270)
Standard sizes within the custom range for Trays 3, 4, and 5 are: 8.5 x 13, RA4, SRA4, 8K (270 x 390), 16K (195 x 270), RA3,
SRA3 , and 12 x 18
Table 7-2 Supported envelopes and postcards
Size Dimensions
Envelope #9 98 x 225 mm (3.88 x 8.88 in)
Tray 1 Trays 2, 3, 4, 5
ENWW Supported paper and print media sizes 95
Table 7-2 Supported envelopes and postcards (continued)
Size Dimensions Tray 1
Envelope #10
Envelope DL
Envelope C5
Envelope B5
105 x 241 mm (4.13 x 9.49 in)
110 x 220 mm (4.33 x 8.66 in)
162 x 229 mm (6.93 x 9.84 in)
176 x 250 mm (6.7 x 9.8 in)
Envelope C6
Envelope
Monarch
162 x 114 mm (6.4 x 4.5 in)
98 x 191 mm (3.9 x 7.5 in)
Double Post Card 148 x 200 mm (5.83 x 7.87 in)
1
US Index Cards 102 x 152 mm (4 x 6 in) and 127 x 203 mm (5 x 8 in)
Weights greater than 160 g/m 2 may not perform well, but will not harm the product.
Trays 2, 3, 4, 5
The following paper sizes are supported with the optional HP 3-bin Stapler/Stacker and HP Booklet
Maker/Finisher accessories.
Table 7-3 Supported paper and print media sizes for the optional HP 3-bin Stapler/Stacker and HP Booklet Maker/
Finisher accessories
Size Dimensions Stacking
Angled staple (leftangled)
Angled staple (rightangled)
Two staples
(top or side)
Folding Saddle stitch
Letter 216 x 279 mm
(8.5 x 11 in)
Letter Rotated 279 x 216 mm
(11 x 8.5 in)
Legal 216 x 356 mm
(8.5 x 14 in)
A4
A4 Rotated
210 x 297 mm
(8.27 x 11.69 in)
297 x 210 mm
(11.69 x 8.27 in)
Executive
8.5 x 13
A3
A5
A6
184 x 267 mm
(7.24 x 10.51 in)
216 x 330 mm
(8.5 x 13 in)
297 x 420 mm
(11.69 x 16.54 in)
148 x 210 mm
(5.83 x 8.27 in)
105 x 148 mm
(4.13 x 5.83 in)
Statement
11 x 17
(Ledger)
140 x 216 mm
(5.5 x 8.5 in)
279 x 432 mm
(11 x 17 in)
96 Chapter 7 Paper and print media ENWW
Table 7-3 Supported paper and print media sizes for the optional HP 3-bin Stapler/Stacker and HP Booklet Maker/
Finisher accessories (continued)
Size Dimensions Stacking
Angled staple (leftangled)
Angled staple (rightangled)
Two staples
(top or side)
Folding Saddle stitch
12 x 18
B4 (JIS)
RA3
SRA3
B5 (JIS)
B6 (JIS)
8K
16K
Envelope 9#
Envelope 10#
Envelope DL
Envelope C5
Envelope B5
Envelope C6
305 x 457 mm
(12 x 18 in)
257 x 364 mm
(10.12 x 14.33 in)
305 x 430 mm
(12 x 16.93 in)
320 x 450 mm
(12.6 x 17.7 in)
257 x 182 mm
(10.12 x 7.17 in)
128 x 182 mm
(5.04 x 7.2 in)
270 x 390 mm
(10.63 x 15.35 in)
195 x 270 mm
(7.68 x 10.63 in)
98.4 x 225.4 mm
(3.88 x 8.88 in)
104.77 x 241.3 mm
(4.12 x 9.5 in)
110 x 220 mm
(4.33 x 8.66 in)
162 x 229 mm
(6.38 x 9.02 in)
176 x 250 mm
(6.93 x 9.84 in)
114 x 162 mm
(4.49 x 6.38 in)
Envelope
Monarch
Double Post
Card
4 x 6 Index
Card
5 x 8 Index
Card
98.42 x 190.5 mm
(3.88 x 7.5 in)
148 x 200 mm
(5.83 x 7.87 in)
102 x 152 mm (4 x 6 in)
127 x 203 mm (5 x 8 in)
Custom Size
1
2
98.55 x 139.70 mm to
320 x 457.2 mm
(3.9 x 5.5 to
12.6 x 18 in)
Booklet maker only
Stacking uses bins 1, 2, and 3 in the stapler/stacker, or bins 1 and 2 in the booklet maker.
ENWW Supported paper and print media sizes 97
Supported paper types
Table 7-4 Tray 1 paper information
Type Specifications
Paper and cardstock, standard sizes
Envelopes
Labels
Transparencies
Heavy
Glossy
Photo media
Cut sheet paper
Tough paper
Quantity Driver settings Paper orientation
Range: Maximum stack height:
10 mm (0.6 in)
Plain or unspecified
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond Equivalent to 100 sheets of 75 g/m 2 (20 lb) bond.
Load preprinted or prepunched paper facing down, with the top edge leading into the tray, or toward the back of the product
Short edge leading, flap toward the front of the product, facing up
Less than 60 g/m 2 (16 lb) bond to 90 g/m 2 (24 lb) bond
Up to 10 envelopes
Maximum 0.23 mm
(0.009 in) thick
Minimum 0.13 mm
(0.005 in) thick
0.13 mm (0.005 in) thick
Maximum stack height:
10 mm (0.6 in)
Maximum stack height:
10 mm (0.6 in)
Envelope
Labels
Transparencies
Side to be printed on facing down
Side to be printed on facing down
Maximum stack height:
10 mm (0.6 in)
Light glossy, glossy, or heavy glossy
Side to be printed on facing down
Range:
75 g/m 2 (20 lb) bond to
220 g/m 2 (58 lb) bond
Maximum stack height:
10 mm (0.6 in)
Light glossy, glossy, or heavy glossy
Side to be printed on facing down
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond
Maximum stack height:
10 mm (0.6 in)
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond
Maximum stack height:
10 mm (0.6 in)
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond
Maximum stack height:
10 mm (0.6 in)
Side to be printed on facing down
Side to be printed on facing down
Side to be printed on facing down
Table 7-5 Trays 2, 3, 4, and 5 paper information
Type
Paper and cardstock, standard sizes
Labels
Transparencies
Heavy
Glossy
Specifications Quantity Settings Paper orientation
Range:
60 g/m 2
220 g/m
(16 lb) bond to
2 (58 lb) bond
Maximum 0.13 mm
(0.005 in) thick
Minimum 0.13 mm
(0.005 in) thick
500 sheets of 75 g/m
(20 lb) bond.
2 Plain or unspecified
Maximum stack height:
54 mm (2.1 in)
Labels
Maximum stack height:
54 mm (2.1 in)
Transparencies
Load preprinted or prepunched paper facing up, with the top toward the back of the tray or toward the righthand side of the tray.
Side to be printed on facing up
Side to be printed on facing up
0.13 mm (0.005 in) thick Maximum stack height:
54 mm (2.1 in)
Light glossy, glossy, or heavy glossy
Side to be printed on facing up
75 g/m 2 (20 lb) bond to
220 g/m 2 (58 lb) bond
Maximum stack height:
54 mm (2.1 in)
Light glossy, glossy, or heavy glossy
Side to be printed on facing up
98 Chapter 7 Paper and print media ENWW
Table 7-5 Trays 2, 3, 4, and 5 paper information (continued)
Type
Photo media
Cut sheet paper
Tough paper
Specifications
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond
60 g/m 2 (16 lb) bond to
220 g/m 2 (58 lb) bond
Quantity Settings Paper orientation
Maximum stack height:
54 mm (2.1 in)
Light glossy, glossy, or heavy glossy
Side to be printed on facing up
Maximum stack height:
54 mm (2.1 in)
Maximum stack height:
54 mm (2.1 in)
Plain or unspecified
HP Tough Paper
Side to be printed on facing up
Side to be printed on facing up
Trays 2, 3, 4, and 5 capacity: 54 mm (2.126 in) height or 500 sheets of paper, whichever is less.
Supported media types include: Cut sheet paper, labels, OHT, glossy paper, glossy film, photo media, and tough paper. Basis Weight: 60-220 g/m 2 (16-58 lb).
Duplex printing: Provides automatic two-sided printing (printing on both sides of the paper). The paper size range for automatic duplex printing is 175 to 320 mm (7.2 to 12.6 in) x 210 to 457 mm (8.3 to 18 in). The media weight range is 60 to 220 g/m 2 (16 to 58 lb)
NOTE: HP Color Laser Presentation Paper, Glossy (Q2546A) is not supported with this product. Using this type of paper can cause a fuser jam that might require the replacement of the fuser. Two recommended alternatives are HP Color LaserJet Presentation Paper, Soft Gloss (Q6541A) and HP
Color LaserJet Brochure Paper, Glossy (Q6611A, Q6610A).
NOTE: For a complete list of specific HP-brand paper that this product supports, go to www.hp.com/ sbso/product/supplies .
ENWW Supported paper types 99
Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory results. When using special paper or print media, be sure to set the type and size in your print driver to obtain the best print results.
CAUTION: HP LaserJet printers use fusers to bond dry toner particles to the paper in very precise dots. HP laser paper is designed to withstand this extreme heat. Using inkjet paper not designed for this technology could damage your printer.
Media type
Envelopes
Labels
Transparencies
Letterhead or preprinted forms
Heavy paper
Glossy or coated paper
Do Do not
● Store envelopes flat.
● Use envelopes where the seam extends all the way to the corner of the envelope.
● Use peel-off adhesive strips that are approved for use in laser printers.
● Do not use envelopes that are wrinkled, nicked, stuck together, or otherwise damaged.
●
●
Do not use envelopes that have clasps, snaps, windows, or coated linings.
Do not use self-stick adhesives or other synthetic materials.
● Use only labels that have no exposed backing between them.
● Do not use labels that have wrinkles or bubbles, or are damaged.
● Do not print partial sheets of labels.
● Use Labels that lie flat.
● Use only full sheets of labels.
● Use only transparencies that are approved for use in laser printers.
● Place transparencies on a flat surface after removing them from the product.
● Do not use transparent print media not approved for laser printers.
● Use only letterhead or forms approved for use in laser printers.
● Use only glossy or coated paper that is approved for use in laser printers.
● Do not use raised or metallic letterhead.
● Use only heavy paper that is approved for use in laser printers and meets the weight specifications for this product.
● Do not use paper that is heavier than the recommended media specification for this product unless it is HP paper that has been approved for use in this product.
● Do not use glossy or coated paper designed for use in inkjet products.
100 Chapter 7 Paper and print media ENWW
Load paper and print media
You can load different media in the trays and then request media by type or size by using the control panel.
Load Tray 1
CAUTION: To avoid jams, never add or remove paper from Tray 1 during printing.
1.
Open Tray 1.
2.
Set the side guides to the correct width, and pull out the tray extensions to support paper.
3.
Load paper in the tray with the side to be printed on face down and the top of the paper or nonpostage end facing the back of the printer.
NOTE: For Letter Rotated and A4 Rotated sizes, place the side to be printed on face down, with the bottom of the page facing into the printer.
4.
Make sure the stack fits under the tabs on the guides and does not exceed the load-level indicators.
5.
Adjust the side guides so that they lightly touch the paper stack but do not bend it.
ENWW Load paper and print media 101
Print envelopes
If your software does not automatically format an envelope, specify Landscape for page orientation in your software program or printer driver. Use the following guidelines to set margins for return and destination addresses on Commercial #10 or DL envelopes:
Address type
Return
Destination
Left margin
15 mm (0.6 in)
102 mm (4 in)
Top margin
15 mm (0.6 in)
51 mm (2 in)
For envelopes of other sizes, adjust the margin settings accordingly.
Load trays 2, 3, 4, or 5
Trays 2, 3, 4, and 5 each hold up to 500 sheets of standard paper or a 54 mm (2.13-inch) stack of labels or other thick paper.
Load standard-sized media into trays 2, 3, 4, or 5
The product automatically detects the following standard sizes of media in these 500-sheet trays: Letter,
Letter rotated, Legal, Executive, 11x17, A3, A4, A4 rotated, A5, B4 (JIS), and B5 (JIS).
CAUTION: Do not print envelopes or unsupported sizes of paper from the 500-trays. Print on these types of paper only from Tray 1.
1.
Slide the tray from the product.
NOTE: Do not open the input tray while it is in use. Doing so can cause jams in the product.
102 Chapter 7 Paper and print media ENWW
2.
Adjust the paper width guide by squeezing the adjustment latch and sliding the guide to the size of the paper being used.
3.
Adjust the paper length guide by squeezing the adjustment latch and sliding the guide to the size of the paper being used.
ENWW Load paper and print media 103
4.
Load paper into the tray face up. Check the paper to verify the guides lightly touch the stack, but do not bend it.
NOTE: To prevent jams, do not overfill the input tray. Be sure the top of the stack is below the tray full indicator.
NOTE: For best performance, fill the tray completely without splitting the ream of paper. Splitting the ream can cause a multifeed problem. The capacity of the paper tray can vary. For example, if you are using 75 g/m 2 (20 lb) paper, the tray holds a full ream of 500 sheets. If the media is heavier, the tray will not hold a full ream. Do not overfill the tray.
NOTE: If the tray is not adjusted correctly, an error message might appear or the media might jam.
5.
Slide the tray into the product. The control panel shows the tray’s paper type and size. If the configuration is not correct, touch Modify on the control panel and select the correct configuration.
If the configuration is correct, touch OK .
Load undetectable standard-sized media into Tray 2, 3, 4, and 5
The following undetectable standard-sized media is supported in the 500-sheet trays:
● Executive (JIS) (8.5 x 13)
● 12 x 18 (Trays 3, 4, or 5 only)
● B4 (ISO)
● RA3 (Trays 3, 4, or 5 only)
104 Chapter 7 Paper and print media ENWW
● SRA3 (Trays 3, 4, or 5 only)
● B5 (ISO)
CAUTION: Do not print envelopes or unsupported sizes of paper from the 500-sheet trays. Print on these types of paper only from Tray 1. Do not overfill the input tray or open it while it is in use. Doing so can cause paper jams.
Load custom-size media into tray 2, 3, 4, or 5
To use custom media, change the size setting on the control panel to Custom and set the unit of measure, X dimension, and Y dimension. See
Configure a tray to match print job settings on page 111 for more information.
1.
Slide open the tray from the product.
2.
Load the print media as described in steps 2 through 4 of the “Load detectable (standard-size) media into Tray 2, 3, 4, or 5” section. Then proceed to step 3 in this procedure.
3.
Slide the tray into the product. The control panel shows the tray type and size configuration. To specify specific custom dimensions, or if the type is not correct, touch Modify when the control panel prompts to change the size or type.
X
ENWW
Y
4.
Select Custom , and then select the Unit of measure , X dimension and Y dimension for the custom paper size.
5.
Select the paper type and then touch Save .
6.
If the configuration is correct, touch Save .
Load paper and print media 105
Load large size paper into Tray 3, 4, or 5
Use the following instructions if you are loading 11x17, RA3, SRA3, or 12 x 18-sized paper into Tray 3,
4, or 5.
1.
Slide open Tray 3, 4, or 5.
2.
Adjust the paper width guide by squeezing the adjustment latch and sliding the guide to the size of the paper being used.
3.
Load the paper into the tray.
4.
Move the paper stop lever to the correct position for the paper being used.
● For SRA3-sized paper, rotate the lever all the way to the left.
● For A3- or 11x17-sized paper, rotate the lever down into the center position.
● For RA3- or 12x18-sized paper, rotate the lever all the way to the right.
5.
Slide the tray into the product. The control panel shows the tray’s media type and size. If the configuration is not correct, touch Modify and configure the tray to the correct type and size. If the configuration is correct, touch OK .
Load letterhead, pre-printed, or pre-punched paper
To correctly print or copy on letterhead, pre-printed, or pre-punched paper, you need to make sure you load the paper correctly into the tray. You might also need to adjust the Image Rotation setting on the product control panel. The Image Rotation setting is used to adjust for languages that read from left to right (the default) or from right to left.
106 Chapter 7 Paper and print media ENWW
Change the Image Rotation setting
1.
At the control panel home screen, scroll down and touch Administration .
2.
Scroll down and touch Device Behavior .
3.
Scroll down and touch Tray Behavior .
4.
Scroll down and touch Image Rotation .
5.
Touch the correct Image Rotation option. The default setting is Left to right .
6.
Touch OK .
Choose the correct orientation for loading letterhead, pre-printed, or pre-punched paper
The tables below should be used as a guide for loading letterhead, pre-printed, or pre-punched paper.
The first table shows the tray-loading orientation when Image Rotation is set to Left to right , which indicates that the language reads left to right. The second table shows the tray-loading orientation when
Image Rotation is set to Right to left , which indicates that the language reads right to left. The tables also contain the following information:
● The paper type: letterhead, pre-printed or pre-punched.
● The paper tray: Tray 1 or Trays 2 through 5.
● Image orientation: Portrait (1) or Landscape (2).
1 2
● One-sided or two-sided (duplex) printing.
● Stapling: The optional stapler/stacker or booklet maker output accessory must be attached in order to staple print or copy jobs. The staple location can be one left, one angled staple located in upper left corner; or two left, two staples located on left long edge. For more information about stapling, see
ENWW
● The arrow in the paper graphic indicates the direction the paper will feed into the printer. The paper graphic indicates the direction the paper should be placed in the paper tray. The default is to load the paper so that the long edge feeds first. This results in the most efficient printing and copying.
Load paper and print media 107
Table 7-6 Load letterhead, pre-printed, or pre-punched paper — Image Rotation = Left to right
Paper type and tray
Image orientation Duplex mode Staple location options
How to load for long-edge feed
How to load for short-edge feed
Letterhead or Preprinted – Tray 1
Portrait 1- sided One left, two left
Letterhead or Preprinted – Tray 1
Portrait 2-sided One left, two left
HP Laserjet
Letterhead or Preprinted – Tray 1
Landscape 1-sided One left, two left
Letterhead or Preprinted – Tray 1
Landscape 2-sided One left, two left
Letterhead or Preprinted – Trays 2-5
Portrait 1-sided One left, two left
HP Laserjet
HP Laserjet
Letterhead or Preprinted – Trays 2-5
Portrait 2-sided One left, two left
Letterhead or Preprinted – Trays 2-5
Landscape 1-sided One left, two left
Letterhead or Preprinted – Trays 2-5
Landscape 2-sided One left, two left
HP Laserjet
108 Chapter 7 Paper and print media ENWW
ENWW
Table 7-6 Load letterhead, pre-printed, or pre-punched paper — Image Rotation = Left to right (continued)
Paper type and tray
Image orientation Duplex mode Staple location options
How to load for long-edge feed
How to load for short-edge feed
Pre-punched –
Tray 1
Portrait 1-sided or 2-sided One left, two left
Pre-punched –
Tray 1
Landscape 1-sided or 2-sided One left, two left
Pre-punched –
Trays 2-5
Portrait 1-sided or 2-sided One left, two left
Pre-punched –
Trays 2-5
Landscape 1-sided or 2-sided One left, two left
Table 7-7 Load letterhead, pre-printed, or pre-punched paper — Image Rotation = Right to left
Paper type and tray
Image orientation Duplex mode Staple location options
How to load for long-edge feed
How to load for short-edge feed
Letterhead or Preprinted – Tray 1
Portrait 1-sided One right, two right
Letterhead or Preprinted – Tray 1
Landscape 2-sided One right, two right
Letterhead or Preprinted – Trays 2-5
Portrait 2-sided One right, two right jet ser HP La
Load paper and print media 109
Table 7-7 Load letterhead, pre-printed, or pre-punched paper — Image Rotation = Right to left (continued)
Paper type and tray
Image orientation Duplex mode Staple location options
How to load for long-edge feed
How to load for short-edge feed
Letterhead or Preprinted – Trays 2-5
Landscape 1-sided One right, two right jet ser HP La
Pre-punched –
Tray 1
Portrait 1-sided or 2-sided One right, two right
Pre-punched –
Tray 1
Landscape 1-sided or 2-sided One right, two right
Pre-punched –
Trays 2-5
Portrait 1-sided or 2-sided One right, two right
Pre-punched –
Trays 2-5
Landscape 1-sided or 2-sided One right, two right
110 Chapter 7 Paper and print media ENWW
Configure trays
The product automatically prompts you to configure a tray for type and size in the following situations:
● When you load paper into the tray
● When you specify a particular tray or media type for a print job through the printer driver or a software program and the tray is not configured to match the print-job’s settings
The following message appears on the control panel: Tray <x> [type] [size] To change size or type, touch “Modify”. To accept, touch “OK” .
NOTE: The prompt does not appear if you are printing from Tray 1 and Tray 1 is configured for Any
Custom and Any Type .
NOTE: If you have used other HP LaserJet product models, you might be accustomed to configuring
Tray 1 to First mode or Cassette mode. On the HP Color LaserJet CM6049f, setting Tray 1 size to Any
Custom is equivalent to First mode. Setting size for Tray 1 to a setting other than Any Custom is equivalent to Cassette mode.
Configure a tray when loading paper
1.
Load paper in the tray. Close the tray if you are using Tray 2, 3, 4, or 5.
2.
The tray configuration message appears.
3.
Touch OK to accept the detected size and type, or touch Modify to choose a different paper size or type.
4.
Select the correct size and type and then touch OK .
NOTE: The product automatically detects most paper sizes in Trays 2, 3, 4, and 5.
Configure a tray to match print job settings
1.
In the software program, specify the source tray, the paper size, and the paper type.
2.
Send the job to the product.
If the tray needs to be configured, the Load Tray x <Type> <Size> message appears.
3.
Load the tray with the specified type and size of paper, and then close the tray.
To specify a custom size, Modify .
4.
When the Tray <x> Size=<Size> message appears, touch OK to confirm the size.
5.
When the Tray<x> Type=<Type> message appears, touch OK to confirm the type and continue with the job.
Automatic media type sensing (auto sense mode)
The automatic media type sensor functions only when that tray is configured to Any Type or Plain type.
Configuring a tray to any other type, such as Bond or Glossy, deactivates the media sensor in that tray.
ENWW Configure trays 111
The HP Color LaserJet CM6049f MFP can automatically classify many paper types into one of the following categories:
● Plain
● Transparency
● Glossy
● Extra-heavy glossy
● Glossy film
● Heavy
For more control, a specific type must be selected in the job or configured in a tray.
Auto sense settings
Full sensing (default for Tray 1)
● The product recognizes light, plain, heavy, glossy, and tough paper and overhead transparencies.
● Each time the product begins a print job, it stops the first page to sense the type.
● This is the slowest mode.
Expanded sensing (default for Trays 2, 3, 4, and 5)
● Each time the product begins a print job, it stops the first page to sense the type.
● The product assumes that the second and all subsequent pages are of the same media type as the first page.
● This is the second-fastest mode, and is useful for using stacks of the same media type.
Transparency only
● The product does not stop any pages for sensing but distinguishes between transparencies
(Transparency mode) and paper (Normal mode).
● This is the fastest mode and is useful for high-volume printing in Normal mode.
For more information about setting these options, see
Select the paper by source, type, or size
In the Microsoft Windows operating system, three settings affect how the printer driver tries to pull media when you send a print job. Source , Type , and Size settings appear in the Page Setup , Print , or Print
Properties dialog boxes in most software programs. Unless you change these settings, the product automatically selects a tray using the default settings.
Source
To print by Source select a specific tray for the product to pull from. If you select a tray that is configured for a type or size that does not match your print job, the product prompts you to load the tray with the type or size of print media for your print job before printing it. When you load the tray, the product begins printing.
112 Chapter 7 Paper and print media ENWW
Type and Size
Printing by Type or Size means that you want the product to pull from the tray that is loaded with the correct type and size of media. Selecting media by type rather than source is similar to locking out trays and helps protect special media from accidental use. For example, if a tray is configured for letterhead and you select plain paper, the product will not pull the letterhead from that tray. Instead, it will pull from a tray that has plain paper loaded and is configured for plain paper on the product control panel. Selecting media by Type and Size results in significantly better print quality for heavy paper, glossy paper, and transparencies. Using the wrong setting might result in unsatisfactory print quality. Always print by Type for special print media, such as labels or transparencies. Print by Size for envelopes, if possible.
● To print by Type or Size, select the Type or Size from the Page Setup dialog box, the Print dialog box, or the Print Properties dialog box, depending on the software program.
● If you often print on a certain type or size of media, configure a tray for that type or size. Then, when you select that type or size as you print a job, the product automatically pulls media from the tray that is configured for that type or size.
ENWW Configure trays 113
Choose an output location
Standard output bins
The product has an ADF output bin and the standard output bin for printed pages.
2
1
1
2
Standard output bin
ADF output bin (for copy originals)
When you scan or copy documents by using the ADF, the originals are automatically delivered to the
ADF output bin. Copies made from the scanner glass are delivered to the standard output bin or the output bin(s) on the stapler/stacker or the 3-bin mailbox.
When you send print jobs to the product from a computer, the output is to the standard output bin or the output bin(s) on the stapler/stacker or the 3-bin mailbox.
Optional output accessories
An optional 3 bin stapler/stacker or booklet-maker finisher accessory can be installed with the product.
When an accessory is installed, an output accessory bridge is also added on top of the product in order to route the print jobs to the accessory output bins.
3-bin stapler/stacker features
Table 7-8 3-bin stapler/stacker features
Job offset Each copy of a job is shifted to one side in the output bin in order to keep each copy separate from the others. (Supported paper sizes: A3, A4, A4 rotated, A5, B4, B5, Ledger, Legal, Letter,
Letter rotated, Statement.)
114 Chapter 7 Paper and print media ENWW
Table 7-8 3-bin stapler/stacker features (continued)
Three operation modes Mailbox Mode assigns each bin to a user or group of users. Stacker Mode uses all three output bins for all print jobs — when one bin is full, jobs are routed to the next bin. Function Separator
Mode sends copies to bin 1, faxes to bin 2, and print jobs to bin 3.
Stapler
Large-capacity output bins
Built-in stapler staples jobs up to 50 sheets in size or 30 stapled jobs. Pages can be stapled in one position at the front, in one position at the back, or at two positions at the side or top.
The stacker has three bins: a 100-sheet bin, a 500-sheet bin, and a 1000-sheet bin.
Booklet maker finisher features
Table 7-9 Booklet-maker finisher features
Booklet-making The booklet-making feature staples and folds print jobs of 2 to 15 pages into a booklet.
Folding
Job offset
Two operation modes
Stapler
Large-capacity output bins
Single-sheet print jobs can be automatically folded in the center.
Each copy of a job is shifted to one side in the output bin in order to keep each copy separate from the others. (Supported paper sizes: A3, A4, A4 rotated, A5, B4, B5, Ledger, Legal, Letter,
Letter rotated, Statement.)
Mailbox Mode assigns each bin to a user or group of users, and Stacker Mode uses both output bins for all print jobs — when the top bin is full, jobs are routed to the next bin.
Built-in stapler staples jobs up to 50 sheets in size or 30 stapled jobs. Pages can be stapled in one position at the front, in one position at the back, or at two positions at the side or top.
The stacker has three bins: two 1000-sheet bins and one bin that can hold up to 25 saddlestitched booklets.
Accessory walkaround
Figure 7-1 3-bin stapler/stacker accessory
1 2 3
4
5
ENWW
1
2
3
4
5
Output bins
Front door
Stapler unit
Top cover
Connection cable
Choose an output location 115
Figure 7-2 Booklet-maker finisher accessory
3
4
5
6
2
5
6
7
1
2
3
4
1
Booklet bin guide
Booklet output bin
Stacking output bins
Front door
Stapler units
Top cover
Connection cable
Use the booklet-making feature
You can create booklets from the print driver or by copying an original document.
Before creating a booklet, set the booklet bin guide for the size of paper being used:
● Closed: 11x17, Legal, A3, or B4
● Open: Letter Rotated, A4 Rotated
7
116 Chapter 7 Paper and print media ENWW
Create a booklet from the print driver
1.
On the File menu of your software program, click Print .
2.
Select HP Color LaserJet CM6049f MFP.
3.
Click Properties , and then click Booklet Printing .
4.
Set the Paper source , Paper sizes , Paper type , Orientation , Booklet Layout , Print document on , and Staple settings, and then click OK .
5.
Click OK to print.
Create a booklet from a copy
Documents can be copied from the automatic document feeder (ADF) or by placing the document on the scanner glass.
1.
From the control panel, touch Copy .
2.
Scroll to and touch Booklet Format .
3.
Touch Booklet on .
4.
For Original Sides touch 1-sided or 2-sided .
5.
Touch OK and then touch Start .
ENWW Choose an output location 117
Configure the accessory operation mode
Select the operating mode at the control panel
You can set the operating mode for the stapler/stacker or the booklet maker at the product control panel.
1.
At the control panel, touch Administration , and then touch Device behavior .
2.
Touch MBM-3 bin stapler or Multifunction finisher .
3.
Touch Operation mode , and then select the operation mode that you want to use.
● When Mailbox Mode is used, each bin is assigned to a user or group of users. Every time a user sends a print job, the job is routed to the assigned bin.
● When Stacker Mode is used and the optional 3-bin stapler/stacker is installed, the three bins act as a single bigger bin. When one bin gets full, jobs are automatically routed to the next bin. When Stacker Mode is used and the booklet maker finisher is installed, the two upper bins act as a single bin, and the third bin is reserved for booklets.
● When Function Separator (3-bin stapler/stacker only) mode is used, each bin is assigned to a specific kind of job. Usually this designation is bin 1 for copies, bin 2 for fax, and bin 3 for printing. These values can be modified in the Default Job Options menus for copy, fax, and print.
NOTE: Use the product embedded Web server to assign output bins to users or groups of users.
For more information see
Embedded Web server on page 178
.
Select the operating mode in the printer driver
1.
Click the Start button, point to Settings , and then click Printers (for Windows 2000) or Printers and Faxes (for Windows XP).
From your Vista computer click Start , click Control Panel , and then in the category for Hardware and Sound click Printer .
2.
Right-click the HP product icon, and then click Properties or Printing Preferences .
3.
Click the Device Settings tab.
4.
Perform one of the following actions:
For automatic configuration: under Installable Options , click Update Now in the Automatic
Configuration list.
-or-
For manual configuration: under Installable Options , select the appropriate operation mode in the
Accessory Output Bin list.
5.
Click Apply to save the settings.
Select the operating mode in the printer driver (Mac OS X)
1.
In the Apple menu, click System Preferences .
2.
In the System Preferences box, click Print and Fax .
3.
Click Set Up Printers . A Printer List displays.
118 Chapter 7 Paper and print media ENWW
4.
Select the HP product, and then click Show Info on the Printers menu.
5.
Select the Installable Options panel.
6.
In the Accessory Output Bins list, select correct accessory.
7.
In the Mailbox Mode list, select the appropriate operational mode, and then click Apply
Changes .
ENWW Choose an output location 119
120 Chapter 7 Paper and print media ENWW
8 Use product features
●
●
●
Job storage features for print jobs
●
Print photos or marketing material
●
Print weatherproof maps and outdoor signs
●
ENWW 121
Economy settings
Sleep and wake
Set the sleep delay
Use the sleep-delay feature to select the time interval the product remains inactive before entering sleep mode. The default is one hour.
1.
Scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Sleep Delay .
4.
Touch the sleep-delay setting that you want and then touch Save .
Set the wake time
Use the wake time feature to wake the product at a set time each day.
1.
Scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Wake Time .
4.
Touch the day of the week for the wake time.
5.
Touch Custom .
6.
Touch Save .
7.
Touch the appropriate options to set the correct hour, minute, and AM/PM setting.
8.
If you want to wake the product at the same time each day, on the Apply to all days screen, touch
Yes . If you want to set the time for individual days, touch No , and repeat the procedure for each day.
Set the sleep time
Use the sleep time feature to program the product to enter sleep mode at a set time each day.
1.
Scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Sleep Time .
4.
Touch the day of the week for the sleep time setting.
5.
Touch Custom .
6.
Touch Save .
122 Chapter 8 Use product features ENWW
7.
Touch the appropriate options to set the correct hour, minute, and AM/PM setting.
8.
If you want the product to enter sleep mode at the same time each day, on the Apply to all days screen, touch Yes . If you want to set the time for individual days, touch No , and repeat the procedure for each day.
Set economy modes from the EWS
1.
From a Web browser, open the EWS. See
Embedded Web server on page 178
.
2.
Click Settings and then Wake Time .
3.
Set the wake time for each day of the week.
4.
Set the sleep delay for the product.
5.
Click Apply .
ENWW Economy settings 123
Use the stapler
The automatic stapler is only available with the optional HP 3-bin Stapler/Stacker (CC517A) or HP booklet Maker/Finisher Accessory (CC516A).
Print jobs can be stapled with a diagonal staple in either top corner, with two horizontal staples at the top of the page, or with two vertical staples at either side of the page.
● Paper weight can range from 60 to 220 g/m 2 (16 to 148 lbs.). Heavier paper might have a stapling limit of fewer than 50 sheets.
● The optional stapler/stacker can staple jobs of up to 50 sheets of 75 g/m 2 (20 lb) paper. It can stack up to 1,000 sheets of paper, or 30 stapled jobs, whichever is less.
● The optional booklet maker can also staple jobs of up to 50 sheets of 75 g/m 2 (20 lb) paper. It can staple and fold up to 15 pages into a booklet. It can stack up to 1,000 sheets of paper, (or 30 stapled jobs) or up to 25 saddle-stitched booklets.
● If the job consists of only one sheet, or if it consists of more than 50 sheets, the product delivers the job to the bin, but does not staple the job.
● The stapler supports paper only. Do not try to staple other types of print media, such as envelopes, transparencies, or labels.
NOTE:
When you want the product to staple or fold a document, select the correct option in the software. You can usually select the stapler in your program or printer driver, although some options might be available only in the printer driver. Where and how you make selections depends on your program or printer driver.
If you cannot select the stapler or booklet maker finisher in the program or printer driver, select it at the product control panel.
The stapler accepts print jobs if it is out of staples, but it does not staple the pages. The product can be configured to stop printing if the staple cartridge is empty.
Supported paper sizes for stapling
In order to staple a print job, you must be a supported paper size and orientation.
Corner, angled staples are supported with the following paper sizes: A4, A4 Rotated, Letter, Letter
Rotated, Legal, A3, 11 x 17, and B4 (JIS).
Two staples at the top or side of the print job are supported with the following paper sizes: A4, Letter,
A3, 11 x 17, and B4 (JIS).
Saddle-stitch stapling with the booklet maker can be carried out with these sizes: A4 Rotated, Letter
Rotated, Legal, A3, 11 x 17, and B4 (JIS).
As shown in the graphic below, the paper must also be loaded into the paper trays with the correct orientation.
124 Chapter 8 Use product features ENWW
A4
LTR
A4
LTR
A4
LTR
If the correct paper size or orientation is not used, the print job will print, but it will not be stapled.
NOTE: For information about loading and stapling print or copy jobs on letterhead, pre-printed, or prepunched paper, see
3-bin stapler/stacker features on page 114
ENWW Use the stapler 125
Staple print jobs
NOTE: For staple job capacity see
3-bin stapler/stacker features on page 114
Select the stapler at the control panel for printed jobs
1.
Touch Administration and then touch Device Behavior .
2.
Touch MBM-3 Bin Stapler or Multifunc Finisher .
3.
Touch Staples .
4.
Touch the option that you want to use: One Left Angled , One Right Angled , Two Left , Two Right , and Two Top .
NOTE: Selecting the stapler at the printer control panel changes the default setting. It is possible that all print jobs will be stapled. However, settings that are changed in the printer driver override settings that are changed at the control panel.
Select the stapler in the printer driver for printed jobs (Windows)
NOTE: The following procedure changes the default setting to staple all print jobs.
1.
Open the printer driver. See
Change printer-driver settings for Windows on page 67 .
2.
On the Output tab, click the drop-down list under Staple , and select a staple option.
Select the stapler in the printer driver for printed jobs (Mac)
Select the stapler by creating a new preset in the printer driver.
1.
Open the printer driver. See
Change printer-driver settings for Macintosh on page 73
.
2.
Create the new preset.
Configure the device to stop or continue when the staple cartridge is empty
You can specify whether the product stops printing when the staple cartridge is empty or if it continues printing but does not staple the jobs.
1.
Touch Administration and then touch Device Behavior .
2.
Touch MBM-3 Bin Stapler or Multifunc Finisher .
3.
Touch Staples Out .
4.
Touch the option that you want to use:
● Select Stop to stop all printing until the staple cartridge is replaced.
● Select Continue to continue printing jobs without stapling them.
126 Chapter 8 Use product features ENWW
Job storage features for print jobs
You can save a print job to the product hard disk without printing it. You can then print the job at any time at the control panel. The following job-storage features are available for print jobs:
● Proof and hold jobs : This feature provides a quick and easy way to print and proof one copy of a job and then print the additional copies.
● Personal jobs : When you send a private job to the device, the job does not print until you provide the required personal identification number (PIN) at the control panel.
● QuickCopy jobs : You can print the requested number of copies of a job and then store a copy of the job on the device hard disk. Storing the job allows you to print additional copies of the job later.
● Stored jobs : You can store a job such as a personnel form, time sheet, or calendar on the device and allow other users to print the job at any time. Stored jobs also can be protected by a PIN.
Follow the instructions in this section to gain access to the job storage features at the computer. See the specific section for the type of job that you want to create.
CAUTION: If you turn off the device, all QuickCopy, proof and hold, and personal jobs are deleted.
Gain access to the job storage features
For Windows
1.
On the File menu, click Print .
2.
Click Properties , and then click the Job Storage tab.
3.
Select the job storage mode that you want.
For Macintosh
In newer drivers: Select Job Storage in the pull-down menu in the Print dialog box. In older drivers, select Printer Specific Options .
Use the proof and hold feature
The proof and hold feature provides a quick and easy way to print and proof one copy of a job and then to print the additional copies.
To permanently store the job and prevent the device from deleting it when space is needed for something else, select the Stored Job option in the driver.
Create a proof and hold job
CAUTION: If the device needs additional space to store newer proof and hold jobs, the device deletes other stored proof and hold jobs, starting with the oldest job. To permanently store a job and prevent the device from deleting it when space is needed, select the Stored Job option in the driver instead of the Proof and Hold option.
In the driver, select the Proof and Hold option and type a user name and job name.
The device prints one copy of the job for you to proof.
ENWW Job storage features for print jobs 127
Print the remaining copies of a proof and hold job
At the device control panel, use the following procedure to print the remaining copies of a job held on the hard disk.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the job.
4.
Scroll to and touch the job that you want to print.
5.
Select the number of copies on the numeric keypad.
6.
Touch Retrieve Stored Job to print the document.
Delete a proof and hold job
When you send a proof and hold job, the device automatically deletes your previous proof and hold job.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the job.
4.
Scroll to and touch the job that you want to delete.
5.
Touch Delete .
6.
Touch Yes .
128 Chapter 8 Use product features ENWW
Use the personal job feature
Use the personal job feature to specify that a job is not printed until you release it. Your job will be stored on the product and nothing will be printed until you request the job from the product's control panel.
Once the job is printed, it will be automatically removed from the product's job storage. Personal jobs can be stored with or without a 4-digit personal identification number (PIN). To make the job private, a
PIN must be used.
Print a personal job
You can print a personal job at the control panel after the job has been sent to the product.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the personal job.
4.
Scroll to and touch the personal job that you want to print.
5.
If a PIN is required, touch the PIN field.
6.
Use the numeric keypad to type the PIN, and then touch OK .
7.
Select the number of copies on the numeric keypad to change the number of copies to print.
8.
Touch Retrieve Stored Job to print the document.
Delete a personal job
A personal job is automatically deleted from the device hard disk after you release it for printing. If you want to delete the job without printing it, use this procedure.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the personal job.
4.
Scroll to and touch the personal job that you want to delete.
NOTE: A personal job will have a lock symbol next to it.
5.
Touch the PIN field.
6.
Use the numeric keypad to type the PIN, and then touch OK .
7.
Touch Delete .
8.
Touch Yes.
ENWW Job storage features for print jobs 129
Use the QuickCopy feature
The QuickCopy feature prints the requested number of copies of a job and stores a copy on the device hard disk. Additional copies of the job can be printed later. This feature can be turned off in the printer driver.
The default number of different QuickCopy jobs that can be stored on the device is 32. At the control panel, you can set a different default number. See
Navigate the Administration menu on page 15 .
Create a QuickCopy job
CAUTION: If the device needs additional space to store newer QuickCopy jobs, the device deletes other stored QuickCopy jobs, starting with the oldest job. To permanently store a job and prevent the device from deleting it when space is needed, select the Job Storage option in the driver instead of the
QuickCopy option.
In the driver, select the QuickCopy option, and then type a user name and a job name.
When you send the job to print, the device prints the number of copies that you set in the driver. To print more quick copies at the device control panel, see
Print additional copies of a QuickCopy job on page 130 .
Print additional copies of a QuickCopy job
This procedure describes how to print additional copies of a job stored on the device hard disk at the control panel.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the job.
4.
Scroll to and touch the job that you want to print.
5.
Select the number of copies on the numeric keypad to change the number of copies to print.
6.
Touch Retrieve Stored Job to print the document.
Delete a QuickCopy job
Delete a QuickCopy job at the device control panel when you no longer need it. If the device requires additional space to store new QuickCopy jobs, the device automatically deletes other stored QuickCopy jobs, starting with the oldest job.
NOTE: Stored QuickCopy jobs can be deleted at the control panel or in HP Web Jetadmin.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the job.
4.
Scroll to and touch the job that you want to delete.
5.
Touch Delete .
6.
Touch Yes .
130 Chapter 8 Use product features ENWW
Use the stored job feature for copy jobs
You also can create a stored copy job at the control panel that can be printed at a later time.
Create a stored copy job
1.
Place the original document face-down on the glass or face-up in the ADF.
2.
From the Home screen, touch Job Storage .
3.
Touch Create .
4.
To create a Job Name, touch the New Job button to open the keyboard.
5.
Type the name of the folder on the touch screen keyboard.
6.
Select Job Name from the drop-down menu.
7.
Type the job name on the touch screen keyboard.
8.
If it is a private job, select PIN to print . Enter the PIN in the popup box.
9.
Touch OK .
10.
After all the options are set, touch Start to scan the document and save the file.
For information about printing the job, see
Print a stored job on page 131
Print a stored job
At the control panel, you can print a job that is stored on the device hard disk.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the stored job.
4.
Scroll to and touch the stored job that you want to print.
5.
Touch Retrieve Stored Job to print the document.
6.
Select the number of copies on the numeric keypad to change the number of copies to print.
7.
Touch Retrieve Stored Job to print the document.
Delete a stored job
Jobs stored on the device hard disk can be deleted at the control panel.
1.
From the Home screen, touch Job Storage .
2.
Touch the Retrieve tab.
3.
Scroll to and touch the job storage folder that holds the stored job.
4.
Scroll to and touch the stored job that you want to delete.
ENWW Job storage features for print jobs 131
5.
Touch Delete .
6.
Touch Yes .
If the file has lock symbol next to it, the job requires a PIN to delete it. See
Use the personal job feature on page 129 .
132 Chapter 8 Use product features ENWW
Print photos or marketing material
You can use the HP Color LaserJet CM6049f to print high-quality color photos, marketing and sales material, or other color documents on glossy paper. To maximize the quality of this output you must do the following:
● Choose the appropriate paper
● Configure the paper tray correctly
● Choose the correct settings in the print driver
Supported glossy paper
HP glossy paper product Product code Product size
Letter
Control panel and print driver settings
HP soft gloss 120 g HP Color Laser Presentation
Paper, Soft Gloss
HP Color Laser Professional
Paper, Soft Gloss
HP Color Laser Brochure
Paper, Glossy
HP Color Laser Superior
Paper, Glossy
Q6541A
Q6542A
Q6611A, Q6610A
Q6616A
HP Color Laser Photo Paper,
Glossy
Q6607A, Q6608A
HP Color Laser Photo Paper,
Glossy
Q6614A
HP Color Laser Photo Paper,
Glossy 4x6
Q8842A
HP Color Laser Photo Paper,
Glossy 10 cm x 15 cm
Q8843A
A4
Letter
A4
Letter
A4
101.6 x 152.4 mm (4 x 6 in)
101.6 x 152.4 mm (4 x 6 in)
HP soft gloss 120 g
HP glossy 160 g
HP glossy 160 g
HP glossy 220 g
HP glossy 220 g
HP glossy 220 g
HP glossy 220 g
CAUTION: HP Color Laser Presentation Paper, Glossy (Q2546A) is not supported with this product.
Using this type of paper can cause a fuser jam that might require the replacement of the fuser. Two recommended alternatives are HP Color LaserJet Presentation Paper, Soft Gloss (Q6541A) and
HP Color LaserJet Brochure Paper, Glossy (Q6611A, Q6610A).
Configure the paper tray
Configure the paper tray for the correct paper type.
1.
Load the paper into Tray 2, 3, 4, or 5.
2.
After you close the tray, the control panel prompts you to configure the paper size and type.
3.
If the correct size and type is displayed, touch OK to accept the detected size and type, or
Modify to choose a different paper size and type.
ENWW Print photos or marketing material 133
4.
When the paper size prompt appears, touch the correct size, and then touch Save .
5.
When the paper type prompt appears, touch the correct type. See the table above to determine the correct paper type.
Configure the driver settings
Carry out the following steps to print to glossy paper from your graphics software program.
1.
Select Print from the File menu of your software program.
2.
Select the HP Color LaserJet CM6049f, and then click Properties or Printing Preferences .
3.
From the Paper type drop-down list, select the same paper type that you configured on the product control panel.
4.
Click OK to save the settings and OK to print. The print job will automatically be printed from the tray that has been configured for glossy paper, optimizing print quality for that type.
134 Chapter 8 Use product features ENWW
Print weatherproof maps and outdoor signs
You can use the HP Color LaserJet CM6049f to print durable, waterproof maps, signs, or menus by using HP Tough Paper. HP Tough Paper is a waterproof, tear-proof, satin finish paper that retains rich, vibrant print color and clarity even when exposed to heavy usage or weather. This avoids the expensive and time-consuming laminating that is required with plain papers. To maximize the quality of this output you must do the following:
● Choose the appropriate paper
● Configure the paper tray correctly
● Choose the correct settings in the print driver
Supported tough paper
HP paper name
HP LaserJet Tough Paper
HP LaserJet Tough Paper
Product code
Q1298A
Q1298B
Product size
Letter
A4
Control panel and print driver settings
HP Tough Paper
HP Tough Paper
Configure the paper tray
Configure the paper tray for the correct paper type.
1.
Load the paper into Tray 2, 3, 4, or 5.
2.
After you close the tray, the control panel prompts you to configure the paper size and type.
3.
If the correct size is displayed, touch OK to accept the detected size, or Modify to choose a different paper size and type.
4.
When the paper size prompt appears, touch the correct size, and then touch Save . When the paper type prompt appears, touch the correct type. See the table above to determine the correct paper type.
Configure the driver settings
Carry out the following steps to print to tough paper from your graphics software program.
1.
Select Print from the File menu of your software program.
2.
Select the HP Color LaserJet CM6049f MFP, and then click Properties or Printing
Preferences .
3.
From the Paper type drop-down list, select the same paper type that you configured on the product control panel.
4.
Click OK to save the settings and OK to print. The print job will automatically be printed from the tray that has been configured for tough paper.
ENWW Print weatherproof maps and outdoor signs 135
Set the duplex alignment
For duplexed documents such as brochures, set the registration for the tray before printing to ensure the pages align.
1.
From the control panel, touch Administration and then touch Print Quality .
2.
Touch Set Registration , and then touch the tray you are adjusting.
3.
Touch Test Page and then touch Print .
4.
Follow the steps on the page that prints.
136 Chapter 8 Use product features ENWW
9 Print tasks
●
●
Use features in the Windows printer driver
ENWW 137
Cancel a print job
You can stop a print request by using the control panel or by using the software program. For instructions about how to stop a print request from a computer on a network, see the online Help for the specific network software.
NOTE: It can take some time for all printing to clear after you have canceled a print job.
Stop the current print job from the control panel
Press Stop on the control panel.
Stop the current print job from the software program
A dialog box will appear briefly on the screen, giving you the option to cancel the print job.
If several requests have been sent to the device through your software, they might be waiting in a print queue (for example, in Windows Print Manager). See the software documentation for specific instructions about canceling a print request from the computer.
If a print job is waiting in a print queue (computer memory) or print spooler (Windows), delete the print job there.
Click Start , click Settings , and then click Printers or Printers and Faxes . Double-click the device icon to open the print spooler. Select the print job that you want to cancel, and then press Delete . If the print job is not cancelled, you might need to shut down and restart the computer. If the job is not in the print spooler, use the Job Status menu from control panel to cancel the job.
138 Chapter 9 Print tasks ENWW
Use features in the Windows printer driver
Open the printer driver
How do I
Open the printer driver
Get help for any printing option
Steps to perform
On the File menu in the software program, click Print . Select the printer, and then click Properties or Preferences .
Click the ?
symbol in the upper-right corner of the printer driver, and then click any item in the printer driver. A pop-up message displays that provides information about the item. Or, click
Help to open the online Help.
Use printing shortcuts
To perform the following tasks, open the printer driver and click the Printing Shortcuts tab.
NOTE: In previous HP printer drivers, this feature was called Quick Sets .
How do I
Use a printing shortcut
Create a custom printing shortcut
Steps to perform
Select one of the shortcuts, and then click OK to print the job with the predefined settings.
a) Select an existing shortcut as a base. b) Select the print options for the new shortcut. c) Click Save As , type a name for the shortcut, and click OK .
Set paper and quality options
To perform the following tasks, open the printer driver and click the Paper/Quality tab.
How do I
Select a page size
Select a custom page size
Select a paper source
Select a paper type
Print covers on different paper
Print the first or last page on different paper
Adjust the resolution of printed images
Steps to perform
Select a size from the Paper size drop-down list.
a) Click Custom . The Custom Paper Size dialog box opens.
b) Type a name for the custom size, specify the dimensions, and click OK .
Select a tray from the Paper source drop-down list.
Select a type from the Paper type drop-down list.
a) In the Special pages area, click Covers or Print pages on different paper , and then click Settings . b) Select an option to print a blank or preprinted front cover, back cover, or both.
Or, select an option to print the first or last page on different paper. c) Select options from the Paper source and Paper type drop-down lists, and then click Add . d) Click OK .
In the Print Quality area, select an option from the first dropdown list. See the printer-driver online Help for information about each of the available options.
ENWW Use features in the Windows printer driver 139
Set document effects
To perform the following tasks, open the printer driver and click the Effects tab.
How do I
Scale a page to fit on a selected paper size
Scale a page to be a percent of the actual size
Print a watermark
Add or edit watermarks
NOTE: The printer driver must be stored on your computer for this to work.
Steps to perform
Click Print document on , and then select a size from the dropdown list.
Click % of actual size , and then type the percent or adjust the slider bar.
a) Select a watermark from the Watermarks drop-down list.
b) To print the watermark on the first page only, click First page only . Otherwise, the watermark is printed on each page.
a) In the Watermarks area, click Edit . The Watermark
Details dialog box opens. b) Specify the settings for the watermark, and then click OK .
Set document finishing options
To perform the following tasks, open the printer driver and click the Finishing tab.
How do I
Print on both sides (Duplex)
Print a booklet
Print multiple pages per sheet
Select page orientation
Steps to perform
Click Print on both sides . If you will bind the document along the top edge, click Flip pages up .
a) Click Print on both sides . b) In the Booklet layout dropdown list, click Left binding or Right binding . The Pages per sheet option automatically changes to 2 pages per sheet .
a) Select the number of pages per sheet from the Pages per sheet drop-down list. b) Select the correct options for Print page borders , Page order , and Orientation .
a) In the Orientation area, click Portrait or Landscape . b) To print the page image upside down, click Rotate by 180 degrees .
Set product output options
To perform the following tasks, open the printer driver and click the Output tab.
NOTE: The options that are available on this tab depend on the finishing device that you are using.
How do I
Select staple options
Select an output bin
Steps to perform
Select a stapling option from the Staple drop-down list.
Select an output bin from the Bin drop-down list.
Set job storage options
To perform the following tasks, open the printer driver and click the Job Storage tab.
140 Chapter 9 Print tasks ENWW
How do I Steps to perform
Print one copy for proof before printing all the copies In the Job Storage Mode area, click Proof and Hold . The product prints the first copy only. A message appears on the product control panel that prompts you to print the rest of the copies.
Temporarily store a private job on the product and print it later a) In the Job Storage Mode area, click Personal Job . b) In the Make Job Private area, enter a 4-digit personal identification number (PIN) (optional).
Temporarily store a job on the product
NOTE: These jobs are deleted if the product is turned off.
In the Job Storage Mode area, click Quick Copy . One copy of the job is printed immediately, but you can print more copies from the product control panel.
In the Job Storage Mode area, click Stored Job .
Permanently store a job on the product
Make a permanently stored job private so that anyone who tries to print it must provide a PIN
Receive notification when someone prints a stored job a) In the Job Storage Mode
Make Job Private
area, click
area, click
Stored Job
PIN to print digit personal identification number (PIN).
. b) In the
, and then enter a 4-
In the Job Notification Options area, click Display Job ID when printing .
Set the user name for a stored job
Specify a name for the stored job
In the User Name area, click User name to use the Windows default user name. To provide a different user name, click
Custom and type the name.
a) In the Job Name area, click Automatic to use the default job name. To specify a job name, click Custom and type the name. b) Select an option from the If job name exists dropdown list. Select Use Job Name + (1-99) to add a number to the end of the existing name, or select Replace Existing
File to overwrite a job that already has that name.
Set color options
To perform the following tasks, open the printer driver and click the Color tab.
How do I
Manually adjust color settings
Turn off color printing and use only shades of gray.
Change the way that colors are rendered
Steps to perform a) In the Color Options area, click Manual , and then click
Settings . b) You can adjust the general settings for Edge
Control, and settings for text, graphics, and photographs. See the online Help in the driver for information about each option.
In the Color Options area, click Grayscale .
In the Color Themes area, select an option from the dropdown list. See the online Help in the driver for information about each option.
Obtain support and product-status information
To perform the following tasks, open the printer driver and click the Services tab.
ENWW Use features in the Windows printer driver 141
How do I Steps to perform
Obtain support information for the product In the Internet Services drop-down list, select a support option, and click Go!
Check the status of the product, including the level of supplies Click the Device and Supplies Status icon. The Device
Status page of the HP embedded Web server opens.
Set advanced printing options
To perform the following tasks, open the printer driver and click the Advanced tab.
How do I Steps to perform
Select advanced printing options
Change the order in which pages are printed
In any of the sections, click a current setting to activate a dropdown list so you can change the setting.
Change the number of copies that are printed
NOTE: If the software program that you are using does not provide a way to print a particular number of copies, you can change the number of copies in the driver.
Changing this setting affects the number of copies for all print jobs. After your job has printed, restore this setting to the original value.
Print colored text as black rather than as shades of gray
Open the Paper/Output section, and then enter the number of copies to print. If you select 2 or more copies, you can select the option to collate the pages.
a) Open the Document Options section, and then open the
Printer Features section. b) In the Print All Text as Black drop-down list, select Enabled .
Load letterhead or preprinted paper the same way for every job, whether printing on one or both sides of the page a) Open the Document Options section, and then open the
Printer Features section. b) In the Alternative Letterhead
Mode drop-down list, select On . c) At the product, load the paper the same way you would for printing on both sides.
a) Open the Document Options section, and then open the
Layout Options section. b) In the Page Order drop-down list, select Front to Back to print the pages in the same order as they are in the document, or select Back to Front to print the pages in the reverse order.
142 Chapter 9 Print tasks ENWW
10 Use color
●
●
●
ENWW 143
Manage color
Setting color options to Automatic typically produces the best possible print quality for the most common printing requirements. However, for some documents, setting the color options manually can enhance the way the document appears. Examples of these documents include marketing brochures that contain many images or documents that are printed on a paper type that is not listed in the printer driver.
Set the color options on page 78 for Macintosh.
Automatic or manual color adjustment
The Automatic color adjustment option optimizes the neutral gray color treatment, halftones, and edge enhancements that are used for each element in a document.
NOTE: Automatic is the default setting and is recommended for printing most color documents.
The Manual color adjustment option allows you to adjust the neutral gray color treatment, halftones, and edge enhancements for text, graphics, and photographs.
Manual color options
You can manually adjust color options for Edge Control, Halftones, and Neutral Grays.
Edge Control
The Edge Control setting determines how edges are rendered. Edge control has three components: adaptive halftoning, Resolution Enhancement technology (REt), and trapping. Adaptive halftoning increases the edge sharpness. Trapping reduces the effect of incorrect color alignment by slightly overlapping the edges of adjacent objects. The color REt option smoothes the edges.
NOTE: If you notice white gaps between objects, or if you notice areas that have a slight shadow of cyan, magenta, or yellow at the edge, choose an edge-control setting that increases the trapping level.
Four levels of edge control are available:
● Maximum is the most aggressive trapping setting. Adaptive halftoning and color REt settings are on.
● Normal is the default trapping setting. Trapping is at a medium level. Adaptive halftoning and color
REt settings are on.
● Light sets trapping at a minimal level. Adaptive halftoning and color REt settings are on.
● Off turns off trapping, adaptive halftoning, and color REt.
Halftone options
Halftone options affect the resolution and clarity of your color output. You can select halftone settings for text, graphics, and photographs independently. The two halftone options are Smooth and Detail .
● The Smooth option provides better results for large, solid-filled print areas. It also enhances photographs by smoothing out fine color gradations. Choose this option when uniform and smooth area fills are top priority.
● The Detail option is useful for text and graphics that require sharp distinctions among lines or colors, or for images that contain a pattern or a high level of detail. Choose this option when sharp edges and details are top priority.
144 Chapter 10 Use color ENWW
NOTE: Some software programs convert text or graphics to bitmap images. In these cases, setting the color options for photographs also affects how text and graphics appear.
Neutral Grays
The Neutral Grays setting determines the method used for creating gray colors that are used in text, graphics, and photographs.
Two values are available for the Neutral Grays setting:
● Black Only generates neutral colors (grays and black) using only black toner. This guarantees neutral colors without a color cast.
● 4-Color generates neutral colors (grays and black) by combining all four toner colors. This method produces smoother gradients and transitions to non-neutral colors, and it produces the darkest black.
Print in grayscale
Select the Print in Grayscale or Print Color as Gray option from the printer driver to print a document in black and white.
Restrict color use
This product includes a Restrict Color setting. A network administrator can use the setting to restrict user access to the color printing in order to conserve color toner. If you are unable to print in color, see your network administrator.
Restrict color printing and copying from the control panel
1.
Scroll to and touch Administration and then touch Management .
2.
Touch Restrict Color Use.
3.
Touch Color printing access or Color copying access .
4.
Select one of the following options:
● Enable Color (default). This setting allows color-printing capabilities for all users.
● Color If Allowed . The setting allows the network administrator to allow color use for select users and/or applications. Use the embedded Web server to designate which users and/or applications can print in color ( Color printing access only).
● Disable Color . This setting denies color-printing capabilities to all users.
5.
Touch Save .
For more information about restricting and reporting color usage, go to www.hp.com/go/coloraccess .
RGB Color (Color Themes)
You can change RGB Color settings from the printer-driver. For more information on accessing the
printer driver, see Set color options on page 141
for Windows and Set the color options on page 78
for
Macintosh.
ENWW Manage color 145
Five values are available for the RGB Color setting:
● Select Default (sRGB) for most printing needs. This setting instructs the product to interpret RGB color as sRGB, which is the accepted standard of Microsoft and the World Wide Web Consortium
(W3C).
● Select Image optimization (sRGB) to enhance documents in which the content is mainly bitmap images, such as .GIF or .JPEG files. This setting instructs the product to use the best color matching for rendering sRGB, bitmap images. This setting has no effect on text or vector-based graphics.
Using glossy paper in combination with this setting provides the maximum enhancement.
● Select AdobeRGB for documents that use the AdobeRGB color space rather than sRGB. For example, some digital cameras capture images in AdobeRGB, and documents that are produced with Adobe PhotoShop use the AdobeRGB color space. When printing from a professional software program that uses AdobeRGB, it is important that you turn off the color management in the software program and allow the product software to manage the color space.
146 Chapter 10 Use color ENWW
Match colors
The process of matching product output color to your computer screen is quite complex because printers and computer monitors use different methods of producing color. Monitors display colors by light pixels using an RGB (red, green, blue) color process, but printers print colors using a CMYK (cyan, magenta, yellow, and black) process.
Several factors can influence your ability to match printed colors to those on your monitor. These factors include:
● Paper
● Printer colorants (inks or toners for example)
● Printing process (inkjet, press, or laser technology for example)
● Overhead lighting
● Personal differences in perception of color
● Software programs
● Printer drivers
● Computer operating system
● Monitors and monitor settings
● Video cards and drivers
● Operating environment (humidity for example)
Keep the above factors in mind when colors on your screen do not perfectly match your printed colors.
For most users, the best method for matching colors on your screen to your product is to print sRGB colors.
Sample book color matching
The process for matching product output to preprinted sample books and standard color references is complex. In general, you can obtain a reasonably good match to a sample book if the inks used to create the sample book are cyan, magenta, yellow, and black. These are usually referred to as process color sample books.
Some sample books are created from spot colors. Spot colors are specially created colorants. Many of these spot colors are outside of the range of the product. Most spot color sample books have companion process sample books that provide CMYK approximations to the spot color.
Most process sample books will state which process standards were used to print the sample book. In most cases they will be SWOP, EURO, or DIC. To get optimal color matching to the process sample book, select the corresponding ink emulation from the product menu. If you cannot identify the process standard, use SWOP ink emulation.
Printing color samples
To use the color samples, select the color sample that is the closest match to the desired color. Use the sample’s color value in your software program to describe the object you wish to match. Colors may
ENWW Match colors 147
vary depending on paper type and the software program used. For more details on how to use the color samples, go to www.hp.com
.
Use the following procedure to print color samples at the product using the control panel:
1.
Touch Administration and then touch Information .
2.
Touch Sample pages/fonts and then touch CMYK samples or RGB samples to print the samples.
PANTONE® color matching
PANTONE has multiple color matching systems. PANTONE MATCHING SYSTEM® is very popular and uses solid inks to generate a wide range of color hues and tints. See www.hp.com
for details on how to use PANTONE Colors with this product.
NOTE: PANTONE Colors generated might not match PANTONE-identified standards. Consult current
PANTONE Publications for accurate color.
148 Chapter 10 Use color ENWW
Advanced color use
HP ImageREt 4800
HP ImageREt 4800 print technology is a system of innovative technologies developed exclusively by
HP to deliver superior print quality. The HP ImageREt system sets itself apart from the industry by integrating technology advancements and optimizing each element of the print system. Several categories of HP ImageREt have been developed for a variety of user needs.
The system uses key color-laser technologies, including image enhancements, smart supplies, and high-resolution imaging, to provide superior images for general office documents and marketing collateral. Optimized for printing on HP color laser high-gloss papers, HP Image REt 4800 provides superior results on all supported paper, and under a variety of environmental conditions.
Paper selection
For the best color and image quality, it is important to select the appropriate paper type from the product menu or from the front panel.
sRGB
Standard red-green-blue (sRGB) is a worldwide color standard originally developed by HP and Microsoft as a common color language for monitors, input devices (scanners, digital cameras), and output devices
(products, printers, plotters). It is the default color space used for HP products, Microsoft operating systems, the Web, and most office software sold today. sRGB is representative of the typical Windows computer monitor today and the convergence standard for high-definition television.
NOTE: Factors such as the type of monitor you use and the room’s lighting can affect the appearance of colors on your screen.
The latest versions of Adobe PhotoShop, CorelDRAW™, Microsoft Office, and many other software programs use sRGB to communicate color. Most importantly, as the default color space in Microsoft operating systems, sRGB has gained broad adoption as a means to exchange color information between software programs and devices using a common definition that assures typical users will experience greatly improved color matching. sRGB improves your ability to match colors between the product, the computer monitor, and other input devices (scanner, digital camera) automatically, without the need to become a color expert.
Print in four colors — CMYK
Cyan, magenta, yellow, and black (CMYK) are the inks used by a printing press. The process is often called four-color printing. CMYK data files are typically used by and originate from graphic arts (printing and publishing) environments. The product will accept CMYK colors through the PS printer driver. The product color-rendering of CMYK is designed to provide rich, saturated colors for text and graphics.
CMYK ink set emulation (HP postscript level 3 emulation)
The product color rendering of CMYK can be made to emulate several standard offset press ink sets.
In some situations, the CMYK color values in an image or document might not be suited to the product.
For example, a document might be optimized for another product. For best results, the CMYK values
ENWW Advanced color use 149
should be adapted to the HP Color LaserJet CM6049f. Select the appropriate color input profile from the printer driver.
● Default CMYK+ . HP CMYK+ technology produces optimal printing results for most printing jobs.
● Specification for Web Offset Publications (SWOP) . Common ink standard in the United States and other countries/regions.
● Euroscale . Common ink standard in Europe and other countries/regions.
● Dainippon Ink and Chemical (DIC) . Common ink standard in Japan and other countries/regions.
● Custom profile . Select this option to use a custom input profile to accurately control color output, for example, to emulate another HP color LaserJet product. To download color profiles, go to www.hp.com
and search for "CM6049 mfp color profile".
150 Chapter 10 Use color ENWW
11 Copy
●
●
●
●
●
●
●
●
Change the copy-collation setting
●
●
Combine copy jobs by using Job Build
●
ENWW 151
Use the Copy screen
From the Home screen, touch Copy to view the Copy screen. Only the first six copy features are immediately visible. In order to view additional copy features, touch More Options .
Set the default copy options
You can use the administration menu to establish default settings that apply to all copy jobs. If necessary, you can override most settings for an individual job. After that job is complete, the product returns to the default settings.
1.
From the Home screen, scroll to and touch Administration .
2.
Touch Default Job Options , and then touch Default Copy Options .
3.
Several options are available. You can configure defaults for all options, or for only some options.
For information about each option, see
Adjust the copy settings on page 153 . The built-in Help
system also provides an explanation of each option. Touch the Help button in the upper-right corner of the screen.
4.
To exit the administration menu, touch the Home button in the upper-left corner of the screen.
Copy from the scanner glass
Use the scanner glass to make as many as 999 copies of small, lightweight media (less than 60 g/m 2 or 16 lb) or heavy media (more than 105 g/m 2 or 28 lb). This includes media such as receipts, newspaper clippings, photographs, old documents, worn documents, and books.
Place original documents face-down on the glass. Align the corner of the original with the upper-left corner of the glass.
To make copies by using the default copy options, use the numeric keypad on the control panel to select the number of copies, and press Start . To use customized settings, touch Copy . Specify the settings, and then press Start . For more information about using customized settings, see
Adjust the copy settings on page 153 .
Copy from the document feeder
Use the document feeder to make as many as 999 copies of a document that has up to 50 pages
(depending on the thickness of the pages). Place the document into the document feeder with the pages facing up.
To make copies by using the default copy options, use the numeric keypad on the control panel to select the number of copies, and press Start . To use customized settings, touch Copy . Specify the settings, and then press Start . For more information about using customized settings, see
Adjust the copy settings on page 153 .
Before starting another copy job, retrieve the original document from the document-feeder output bin that is under the document feeder input tray, and retrieve the copies from the appropriate output bin.
152 Chapter 11 Copy ENWW
Adjust the copy settings
The product offers several features so you can optimize copied output. These features are all available on the Copy screen.
The Copy screen consists of several pages. From the first page, touch More Options to go to the next page. Then touch the up or down arrow buttons to scroll to other pages.
For details about how to use an option, touch the option, and then touch the help button in the upperright corner of the screen. The following table provides an overview of the copy options.
NOTE: Depending on how the system administrator has configured the product, some of these options might not appear. The options in the table are listed in the order in which they can appear.
Option name
Sides
Reduce/Enlarge
Color/Black
Staple/Collate or Collate
Paper Selection
Image Adjustment
Content Orientation
Output Bin
Optimize Text/Picture
Pages per Sheet
Original Size
Book Copy
Booklet Format
Edge-To-Edge
Job Build
Description
Use this feature to indicate whether the original document is printed on one or both sides, and whether the copies should be printed on one or both sides.
Use this feature to reduce or enlarge the copied image on the page.
Use this feature to choose black printing or color printing.
If the optional HP Stapler/Stacker/Separator is attached, the Staple/Collate option is available.
Use this feature to set up options for stapling and assembling the pages in sets of copies.
If the optional HP Stapler/Stacker/Separator is not attached, the Collate option is available. Use this feature to assemble each set of copied pages in the same order as the original document.
Use this feature to select the tray that holds the size and type of paper that you want to use.
Use this feature to improve the overall quality of the copy. For example, you can adjust the darkness and sharpness, and you can use the Background Cleanup setting to remove faint images from the background or to remove a light background color.
Use this feature to specify the way the content of the original page is placed on the page: portrait or landscape.
Use this feature to select an output bin for the copies.
Use this feature to optimize the output for a particular type of content. You can optimize the output for text or printed pictures, or you can manually adjust the values.
Use this feature to copy multiple pages onto one sheet of paper.
Use this feature to describe the page size of the original document.
Use this feature to scan and print pages from a book.
Use this feature to copy two or more pages onto one sheet of paper so you can fold the sheets in the center to form a booklet.
Use this feature to avoid shadows that can appear along the edges of copies when the original document is printed close to the edges. Combine this feature with the Reduce/Enlarge feature to ensure that the entire page is printed on the copies.
Use this feature to combine several sets of original documents into one copy job. Also use this feature to copy an original document that has more pages than the document feeder can accommodate at one time.
ENWW Adjust the copy settings 153
Copy two-sided documents
Two-sided documents can be copied manually or automatically.
Copying two-sided documents manually
Copies resulting from this procedure are printed on one side, and need to be hand-collated.
1.
Load the documents to be copied into the document feeder input tray with the first page facing up, and with the top of the page leading into the document feeder.
2.
Touch Start Copy . The odd-numbered pages are copied and printed.
3.
Remove the stack from the document feeder output tray and reload the stack with the last page facing up, and with the top of the page leading into the document feeder.
4.
Touch Start Copy . The even-numbered pages are copied and printed.
5.
Collate the odd- and even-numbered printed copies.
Copy two-sided documents automatically
The default copy setting is one-sided to one-sided. Use the following procedures to change the setting so you can copy from or to documents that are two-sided.
Make two-sided copies from one-sided documents
1.
Load the documents to be copied into the document feeder with the first page facing up, and with the top of the page leading.
2.
On the control panel, touch Copy .
3.
Touch Sides .
4.
Touch 1-sided original, 2-sided output .
5.
Touch OK .
6.
Touch Start Copy .
Make two-sided copies from two-sided documents
1.
Load the documents to be copied into the document feeder with the first page facing up, and with the top of the page leading.
2.
On the control panel, touch Copy .
3.
Touch Sides .
154 Chapter 11 Copy ENWW
4.
Touch 2-sided original, 2-sided output .
5.
Touch OK .
6.
Touch Start Copy .
Make one-sided copies from two-sided documents
1.
Load the documents to be copied into the document feeder with the first page facing up, and with the top of the page leading.
2.
On the control panel, touch Copy .
3.
Touch Sides .
4.
Touch 2-sided original, 1-sided output .
5.
Touch OK .
6.
Touch Start Copy .
ENWW Copy two-sided documents 155
Copy mixed-size originals
You can copy original documents that are printed on different sizes of paper as long as the sheets of paper have one common dimension. For example, you could combine letter and legal sizes, or you could combine A4 and A5 sizes.
1.
Arrange the sheets in the original document so they all have the same width.
2.
Place the sheets face-up into the document feeder, and adjust both paper guides against the document.
3.
From the Home screen, touch Copy .
4.
Touch Original Size .
NOTE: If this option is not on the first screen, touch More Options until the option appears.
5.
Select Mixed Ltr/Lgl , and then touch OK .
6.
Touch Start Copy .
156 Chapter 11 Copy ENWW
Change the copy-collation setting
You can set the device to automatically collate multiple copies into sets. For example, if you are making two copies of three pages and the automatic collation is on, the pages print in this order: 1,2,3,1,2,3. If automatic collation is off, the pages print in this order: 1,1,2,2,3,3.
To use the automatic collation, the original document size must fit into the memory. If it does not, the device makes only one copy and a message appears notifying you of the change. If that happens, use one of the following methods to finish the job:
● Split the job into smaller jobs that contain fewer pages.
● Make only one copy of the document at a time.
● Turn off the automatic collation.
The collation setting you select is in effect for all copies until you change the setting. The default setting for automatic copy collation is On .
1.
On the control panel, touch Copy .
2.
Touch Staple/Collate or Collate .
3.
Touch Off .
4.
Touch OK .
ENWW Change the copy-collation setting 157
Copy photos and books
Copy a photo
NOTE: Photos should be copied from the flatbed scanner, not from the document feeder.
1.
Lift the lid and place the photo on the flatbed scanner with the picture-side down and the upperleft corner of the photo in the upper-left corner of the glass.
2.
Gently close the lid.
3.
Touch Copy .
4.
Touch Optimize Text/Picture and select Photograph .
5.
Touch Start Copy .
Copy a book
1.
Place the book face down on the glass with the top edge toward the rear of the glass. Align the book spine with the book icon along the top edge of the glass.
2.
Touch Copy .
3.
Scroll to and touch Book Copy .
4.
Touch Book Copy On and then touch OK .
5.
Select the number of copies to make and adjust other settings as needed.
6.
Touch Start Copy , or press the Start button on the control panel.
7.
The following 3 options are available when Start Copy is touched:
● Copy both pages copies the images on both the left and right side of the spine
● Skip left page copies the image on the right side of the spine only
● Skip right page copies the image on the left side of the spine only
8.
Touch Scan .
9.
After the last page is scanned, touch Finish .
158 Chapter 11 Copy ENWW
Combine copy jobs by using Job Build
Use this feature to combine several sets of original documents into one copy job. Also use this feature to copy an original document that has more pages than the document feeder can accommodate at one time.
1.
Touch Copy .
2.
Scroll to and touch Job Build .
3.
Touch Job Build On .
4.
Touch OK .
5.
If necessary, select the desired copy options.
6.
Touch Start Copy . After each page is scanned, the control panel prompts you for more pages.
7.
If the job contains more pages, load the next page, and then touch Scan .
The product temporarily saves all the scanned images. The product will begin printing copies when it has enough information to begin. Touch Finish to finish printing the copies.
NOTE: In Job Build, if you scan the first page of a document by using the document feeder, then you must scan all of the pages in that document by using the document feeder. If you scan the first page of a document by using the scanner glass, then you must scan all of the pages in that document by using the scanner glass.
ENWW Combine copy jobs by using Job Build 159
Cancel a copy job
1.
Touch the Stop button on the control panel and then touch the job from the list.
2.
Touch Cancel Job and then touch OK .
NOTE: If you cancel a copy job, clear the document from the flatbed scanner or from the automatic document feeder.
160 Chapter 11 Copy ENWW
12 Scan and send to e-mail
●
●
●
Perform basic e-mail functions
●
●
Change e-mail settings for the current job
●
●
Scan to a workflow destination
ENWW 161
Configure e-mail settings
The product offers color-scanning and digital-sending capabilities. By using the control panel, you can scan black-and-white or color documents and send them to an e-mail address as an e-mail attachment.
To use digital sending, the product must be connected to a local area network (LAN).
NOTE: The e-mail icon is not shown on the control panel if e-mail is not configured.
Before you can send a document to e-mail, you must configure the product.
NOTE: The instructions that follow are for configuring the product at the control panel. You can also perform these procedures by using the embedded Web server. For more information, see
Embedded Web server on page 178 .
Supported protocols
The HP Color LaserJet CM6049f MFP supports Simple Mail Transfer Protocol (SMTP) and Lightweight
Directory Access Protocol (LDAP).
SMTP
● SMTP is a set of rules that define the interaction between programs that send and receive e-mail.
In order for the device to send documents to e-mail, it must be connected to a LAN that has access to an e-mail server that supports SMTP. The SMTP server must also have Internet access.
● If you are using a LAN connection, contact your system administrator to obtain the IP address or host name for your SMTP server. If you are connecting through a DSL or cable connection, contact the internet service provider to obtain the SMTP server IP address.
LDAP
● LDAP is used to gain access to a database of information. When the device uses LDAP, it searches a global list of e-mail addresses. As you begin to type the e-mail address, LDAP uses an autocomplete feature that supplies a list of e-mail addresses that match the characters you type. As you type additional characters, the list of matching e-mail addresses becomes smaller.
● The device supports LDAP, but a connection to an LDAP server is not required in order for the device to be able to send to e-mail.
NOTE: If you need to change the LDAP settings, you must change them by using the embedded
Web server. For more information, see
Embedded Web server on page 178 , or see the
Embedded
Web Server User Guide .
Configure e-mail server settings
Find the SMTP gateway
1.
From the Home screen, touch Administration
2.
Touch Initial Setup .
3.
Touch E-mail Setup , and then touch Find Send Gateways .
4.
Touch Find .
162 Chapter 12 Scan and send to e-mail ENWW
Configure the SMTP gateway address
1.
From the Home screen, touch Administration .
2.
Touch Initial Setup .
3.
Touch E-mail Setup , and then touch SMTP Gateway .
4.
Type the SMTP gateway address, either as an IP address or as a fully qualified domain name. If you do not know the IP address or domain name, contact the network administrator.
5.
Touch Save .
Test the SMTP settings
1.
From the Home screen, touch Administration .
2.
Touch Initial Setup .
3.
Touch E-mail Setup , and then touch Test .
If the configuration is correct, Gateways OK appears on the control-panel display.
If the first test was successful, send an e-mail to yourself by using the digital-send feature. If you receive the e-mail, you have successfully configured the digital-sending feature.
If you do not receive the e-mail, use these actions to resolve issues with the digital-sending software:
● Check the SMTP and address to make sure that you typed them correctly.
● Print a configuration page. Verify that the SMTP gateway address is correct.
● Make sure that the network is operating correctly. Send an e-mail to yourself from a computer. If you receive the e-mail, the network is operating correctly. If you do not receive the e-mail, contact your network administrator or Internet service provider (ISP).
ENWW Configure e-mail settings 163
Use the Send E-mail screen
Use the touchscreen to navigate through the options on the Send E-mail screen.
1 Send E-mail button Touching this button scans the document and sends an e-mail file to the provided e-mail addresses.
Touching this button opens the Home screen.
2 Home button
3 From: field Touch this field to open the keyboard, and then type your e-mail address. If the system administrator has configured the device to do so, this field might automatically insert a default address.
4 To: field
5 Subject: field
Touch this field to open the keyboard, and then type the e-mail addresses of those whom you want to receive the scanned document.
Touch this field to open the keyboard, and then type a subject title.
6 More Options button Touch this button to change certain e-mail settings for the current scan job.
7 Scroll bar Use the scroll bar to view and set up the CC: , BCC: , Message , and File Name fields. Touch any of those fields to open the keyboard and add the necessary information.
8 Address book buttons Touch these buttons to use the address book to populate the To: , CC: , or BCC: fields. For more information, see
Use the local address book on page 167 .
9 Help button Touch this button for control-panel help. For more information, see
.
10 Error/warning button This button appears only when there is an error or warning in the status line area. Touch it to open a pop-up screen that will help you resolve the error or warning.
164 Chapter 12 Scan and send to e-mail ENWW
Perform basic e-mail functions
The product e-mail feature offers the following benefits:
● Sends documents to multiple e-mail addresses, saving time and delivery costs.
● Delivers files in black-and-white or in color. Files can be sent in different file formats that the recipient can manipulate.
With e-mail, documents are scanned into the product memory and sent to an e-mail address or multiple addresses as an e-mail attachment. Digital documents can be sent in several graphics formats, such as .TFF and .JPG, which allows recipients to manipulate the document file in various programs to meet their specific needs. Documents arrive in near-original quality, and then can be printed, stored, or forwarded.
In order to use the e-mail feature, the product needs to be connected to a valid SMTP local area network that includes Internet access.
Load documents
You can scan a document by using either the glass or the ADF. The glass and ADF can accommodate
Letter-, Executive-, A4-, and A5-size originals. The ADF can also accommodate Legal-size originals.
Smaller originals, receipts, irregular and worn documents, stapled documents, previously folded documents, and photographs should be scanned by using the glass. Multiple-page documents can be scanned easily by using the ADF.
Send documents
The product scans both black-and-white and color originals. You can use default settings or change the scanning preferences and file formats. The following are the default settings:
● Color
● PDF (requires the recipient to have an Adobe Acrobat viewer to view the e-mail attachment)
For information about changing the settings for the current job, see
Change e-mail settings for the current job on page 168 .
Send a document
1.
Place the document face-down on the scanner glass or face-up in the ADF.
2.
From the Home screen, touch E-mail .
3.
If prompted, type your user name and password.
4.
Complete the From: , To: , and Subject: fields. Scroll down and complete the CC: , and BCC: fields if appropriate. Your user name or other default information might appear in the From: field. If so, you might not be able to change it.
5.
(Optional) Touch More Options to change the settings for the document that you are sending (for example, the document’s original size). If you are sending a two-sided document, you should select
Sides and an option with a two-sided original.
6.
Press Start to begin sending.
7.
When you are finished, remove the original document from the scanner glass or ADF.
ENWW Perform basic e-mail functions 165
Use the auto-complete function
When you type characters into the To: , CC: , or From: fields on the Send E-mail screen, the autocomplete function is activated. As you type the required address or name by using the keyboard screen, the device automatically searches the address book list and completes the address or name by using the first match. You can then select that name by touching Enter , or continue typing the name until autocomplete finds the correct entry. If you type a character that does not match any entry in the list, the auto-complete text is removed from the display to indicate that you are typing an address that is not in the address book.
Use the address book
You can send e-mail to a list of recipients by using the address book feature of the product. See your system administrator for information about configuring address lists.
NOTE: You can also use the embedded Web server (EWS) to create and manage the e-mail address book. The EWS e-mail address book can be used to add, edit, or delete single e-mail addresses or email distribution lists. For more information, see
Embedded Web server on page 178 .
Create a recipient list
1.
From the Home screen, touch E-mail .
2.
Complete one of the following steps:
● Touch To: to open the keyboard screen, and then type the recipients' e-mail addresses.
Separate multiple e-mail addresses with a semicolon or by touching Enter on the touchscreen.
● Use the address book.
a.
On the Send E-mail screen, touch the address book button to open the address book.
b.
Navigate the entries in the address book by using the scroll bar. Hold down the arrow to scroll quickly through the list.
c.
Highlight the name to select a recipient, and then touch the arrow button .
You can also select a distribution list by touching the drop-down list at the top of the screen and then touching All , or add a recipient from a local list by touching Local in the drop-down list. Highlight the appropriate names, and then touch the arrow button to add the name to your list of recipients.
You can remove a recipient from your list by scrolling to highlight the recipient, and then touching the remove button in the middle of the screen.
3.
The names in the recipient list are placed in the text line of the keyboard screen. If you want, you can add a recipient that is not found in the address book by typing the e-mail address on the keyboard. After you are satisfied with your recipient list, touch OK .
4.
Touch OK .
5.
Finish typing information in the CC: and Subject: fields on the Send E-mail screen, if necessary.
You can check the list of recipients by touching the down arrow in the To: text line.
6.
Press Start .
166 Chapter 12 Scan and send to e-mail ENWW
Use the local address book
Use the local address book to store frequently-used e-mail addresses. The local address book can be shared between devices that use the same server to gain access to the HP Digital Sending software.
You can use the address book when you type e-mail addresses in the From: , To: , CC: , or BCC: fields.
You can also add or delete addresses in the address book.
To open the address book, touch the address book button .
Add e-mail addresses to the local address book
1.
Touch Local .
2.
Touch the add button .
3.
(Optional) Touch the Name field, and in the keyboard that appears type a name for the new entry.
Touch OK .
The name is the alias for the e-mail address. If you do not type an alias name, the alias will be the e-mail address itself.
4.
Touch the Address field, and in the keyboard that appears type the e-mail address for the new entry. Touch OK .
Delete e-mail addresses from the local address book
You can delete e-mail addresses that you no longer use.
NOTE: To change an e-mail address, you must first delete the address and then add the corrected address as a new address in the local address book.
1.
Touch Local .
2.
Touch the e-mail address that you want to delete.
3.
Touch the remove button in the lower right corner.
The following confirmation message appears: Do you want to delete the selected address(es)?
4.
Touch Yes to delete the e-mail address(es) or touch No to return to the Address Book screen.
ENWW Use the address book 167
Change e-mail settings for the current job
Use the More Options button to change the following e-mail settings for the current print job:
Button Description
Document File Type Touch this button to change the type of file the device creates after scanning the document.
Output Quality Touch this button to increase or decrease the print quality of the file being scanned. A higher quality setting produces a larger file size.
Resolution
Color/Black
Touch this button to change the scan resolution. A higher resolution setting produces a larger file size.
Touch this button to determine whether you will scan the document in color or in black-and-white.
Original Sides Touch this button to indicate if the original document is one-sided or two-sided.
Content Orientation Touch this button to select either the portrait or landscape orientation for the original.
Original Size
Optimize Text/
Picture
Job Build
Touch this button to select the size of the document: letter, A4, legal, or mixed letter/legal.
Touch this button to change the scanning procedure based on the type of document that you are scanning.
Image Adjustment
Touch this button to activate or deactivate the Job Build mode, which enables you to scan several small scan jobs and send them as one file.
Touch this button to change the darkness and sharpness settings, or to clean up background clutter on the original.
168 Chapter 12 Scan and send to e-mail ENWW
Scan to a folder
If the system administrator has made the feature available, the device can scan a file and send it to a folder on the network. Supported operating systems for folder destinations include Windows 2000,
Windows XP, Windows Server 2003, Windows Server 2008, and Windows Vista.
NOTE: You might be required to supply a user name and password in order to use this option, or to send to certain folders. See your system administrator for more information.
1.
Place the document face-down on the scanner glass or face-down in the ADF.
2.
From the Home screen, touch Network Folder .
3.
In the Quick Access Folders list, select the folder in which you want to save the document.
4.
Touch the File Name field to open the keyboard pop-up screen, and then type the file name.
5.
Touch Send to Network Folder .
ENWW Scan to a folder 169
Scan to a workflow destination
NOTE: This device feature is provided by the optional Digital Sending Software.
If the system administrator has enabled the workflow functionality, you can scan a document and send it to a custom workflow destination. A workflow destination gives you the ability to send additional information, along with the scanned document, to a specified network or file transfer protocol (FTP) location. Prompts for specific information appear on the control-panel display. The system administrator can also designate a printer as a workflow destination, which allows you to scan a document and then send it directly to a network printer for printing.
1.
Place the document face-down on the scanner glass or face-up in the ADF.
2.
From the Home screen, touch Workflow .
3.
Select the destination to which you want to scan.
4.
In the Text Field field, type the data that you want to accompany the file, and then touch Send
Workflow .
170 Chapter 12 Scan and send to e-mail ENWW
13 Fax
●
●
ENWW 171
Analog fax
When the analog fax accessory is installed, the product can function as a standalone fax machine.
The HP Color LaserJet CM6049f comes with a fax accessory already installed. Specifications for the
Analog Fax Accessory are available in the HP LaserJet Analog Fax Accessory 300 User Guide . The
Analog Fax Accessory 300 Fax Guide and the Analog Fax Accessory 300 Send Fax Driver Guide are also located at www.hp.com/go/mfpfaxaccessory300 .
Connect the fax accessory to a phone line
When connecting the fax accessory to a phone line, ensure that the phone line being used for the fax accessory is a dedicated line that is not used by any other devices. Also, this line should be an analog line because the fax will not function correctly if it is connected to some digital PBX systems. If you are not sure whether you have an analog or digital phone line, contact your telecom provider.
NOTE: HP recommends using the phone cord that comes with the fax accessory to ensure that the accessory functions correctly.
Follow these instructions to connect the fax accessory to a phone jack.
1.
Locate the phone cord that is included with the fax accessory kit. Connect one end of the phone cord into the fax accessory phone jack that is on the formatter. Push the connector until it clicks.
CAUTION: Be sure to connect the phone line to the fax accessory port, which is located in the center of the formatter. Do not connect the phone line to the HP Jetdirect port, which is nearer the bottom of the formatter.
2.
Connect the other end of the phone cord into the phone jack on the wall. Push the connector until it clicks or until it is securely seated. Because different types of connectors are used in different countries/regions, the connector might not make an audible click.
Configure and use the fax features
Before you can use the fax features, you must configure them in the control-panel menus. For complete information about configuring and using the fax accessory, and for information about troubleshooting problems with the fax accessory, see the HP LaserJet Analog Fax Accessory 300 User Guide . This guide is provided with the fax accessory.
Use the Send Fax driver to send a fax from a computer without going to the product control panel. See the HP LaserJet MFP Analog Fax Accessory 300 Send Fax Driver Guide for more information.
172 Chapter 13 Fax ENWW
The HP LaserJet Analog Fax Accessory 300 User Guide and HP LaserJet MFP Analog Fax Accessory
300 Send Fax Driver Guide are both available at www.hp.com/go/mfpfaxaccessory300 .
ENWW Analog fax 173
Digital fax
Digital faxing is available when you install the optional HP Digital Sending Software. For information about ordering this software, go to www.hp.com/go/digitalsending
With digital faxing, the product does not need to be connected directly to a phone line. Instead, the product can send a fax in one of three ways:
● LAN fax sends faxes through a third-party fax provider.
● Microsoft Windows 2000 fax is a fax modem and Digital Sender Module on a computer that allows the computer to operate as a turnkey gateway fax.
● Internet fax uses an Internet fax provider to process faxes, and the fax is delivered on a traditional fax machine or sent to the user’s e-mail.
For complete information about using digital faxing, see the documentation that is provided with the
HP Digital Sending Software.
174 Chapter 13 Fax ENWW
14 Manage and maintain the product
●
●
●
●
●
●
●
●
●
●
●
ENWW 175
Information pages
Information pages provide details about the device and its current configuration. The following table provides the instructions for printing the information pages.
Page description How to print the page from the product control panel
Menu map
Shows the control-panel menus and available settings.
1.
From the Home screen, touch Administration .
2.
Touch Information .
3.
Touch Configuration/status Pages .
4.
Touch Administration Menu Map .
5.
Touch Print .
The content of the menu map varies, depending on the options currently installed in the device.
For a complete list of control panel menus and possible values, see
Use the control panel on page 12 .
1.
From the Home screen, touch Administration .
2.
Touch Information .
Configuration page
Shows device settings and installed accessories.
3.
Touch Configuration/Status Pages .
4.
Touch Configuration Page .
5.
Touch Print .
NOTE: If the device contains an HP Jetdirect print server or an optional hard disk drive, additional configuration pages print that provide information about those devices.
1.
From the Home screen, touch Administration .
Supplies status page
Shows print-cartridge toner levels.
2.
Touch Information .
3.
Touch Configuration/status Pages .
4.
Touch Supplies Status Page .
5.
Touch Print .
NOTE: If you are using non-HP supplies, the supplies status page might not show the remaining life for those supplies.
1.
From the Home screen, touch Administration .
Usage page
Shows a page count for each size of paper printed, the number of one-sided
(simplexed) or two-sided (duplexed) pages, and the average percentage of coverage.
2.
Touch Information .
3.
Touch Configuration/status Pages .
4.
Touch Usage Page .
5.
Touch Print .
176 Chapter 14 Manage and maintain the product ENWW
ENWW
Page description How to print the page from the product control panel
Color usage job log
File directory
Contains information for any mass storage devices, such as flash drives, memory cards, or hard disks, that are installed in the device.
1.
From the Home screen, touch Administration
2.
Touch Information
3.
Touch Configuration/status Pages
4.
Touch Color Usage Job Log
5.
Touch Print
1.
From the Home screen, touch Administration .
2.
Touch Information .
3.
Touch Configuration/status Pages .
4.
Touch File Directory .
Fax reports
5.
Touch Print .
1.
From the Home screen, touch Administration .
Five reports show fax activity, fax calls, billing codes, blocked fax numbers, and speed-dial numbers.
2.
Touch Information .
3.
Touch Fax Reports .
NOTE: Fax reports are available only on device models that have fax capabilities.
4.
Touch one of the following buttons to print the corresponding report:
◦ Fax Activity Log
◦ Fax Call Report
◦
◦
◦
Billing Codes Report
Blocked Fax List
Speed Dial List
5.
Touch Print .
Font lists
Shows which fonts are currently installed in the device.
For more information, see the fax guide that came with the device.
1.
From the Home screen, touch Administration .
2.
Touch Information .
3.
Touch Sample Pages/Fonts .
4.
Touch one of the following buttons to print the corresponding report:
◦
◦ Demonstration Page
RGB Samples
◦
◦
◦
CMYK Samples
PCL Font List
PS Font List
5.
Touch Print .
NOTE: The font lists also show which fonts reside on a hard disk accessory or
DIMM.
Information pages 177
Embedded Web server
Use the embedded Web server to view product and network status and to manage printing functions from your computer instead of from the product control panel. The following are examples of what you can do using the embedded Web server:
● Determine the remaining life for all supplies and order new ones.
● View and change tray configurations.
● View and change the product control-panel menu configuration.
● View and print internal pages.
● Receive notification of product and supplies events.
● View and change network configuration.
To use the embedded Web server, you must have Microsoft Internet Explorer 5.01 or later or Netscape
6.2 or later for Windows, Mac OS, and Linux (Netscape only). Netscape Navigator 4.7 is required for
HP-UX 10 and HP-UX 11. The embedded Web server works when the product is connected to an IPbased network. The embedded Web server does not support IPX-based product connections. You do not have to have Internet access to open and use the embedded Web server.
When the product is connected to the network, the embedded Web server is automatically available.
NOTE: For complete information about using the embedded Web server, see the Embedded Web
Server User Guide .
Open the embedded Web server by using a network connection
1.
In a supported Web browser on your computer, type the device IP address or host name in the address/URL field. To find the IP address or host name, print a configuration page. See
Information pages on page 176 .
NOTE: After you open the URL, you can bookmark it so that you can return to it quickly in the future.
2.
The embedded Web server has four tabs that contain settings and information about the device: the Information tab, the Settings tab, the Networking tab, and the Digital Sending tab. Click the tab that you want to view.
See
Embedded Web server sections on page 179 for more information about each tab.
178 Chapter 14 Manage and maintain the product ENWW
Embedded Web server sections
Tab or section
Information tab
Provides device, status, and configuration information
Options
● Device Status : Shows the device status and shows the life remaining of HP supplies, with 0% indicating that a supply is empty. The page also shows the type and size of print paper set for each tray. To change the default settings, click Change
Settings .
● Configuration Page : Shows the information found on the configuration page.
● Supplies Status : Shows the life remaining of HP supplies, with 0 percent indicating that a supply is empty. This page also provides supplies part numbers. To order new supplies, contact your dealer.
● Event log : Shows a list of all device events and errors.
● Usage page : Shows a summary of the number of pages the device has printed, grouped by size and type.
● Device Information : Shows the device network name, address, and model information. To change these entries, click Device Information on the Settings tab.
● Control Panel : Shows messages from the device control panel, such as Ready or
Sleep mode on .
● Print : Allows you to send print jobs to the device.
ENWW Embedded Web server 179
Tab or section Options
Settings tab ● Configure Device : Allows you to configure device settings. This page contains the traditional menus found on devices using a control-panel display.
Provides the ability to configure the device from your computer ● E-mail Server : Network only. Used in conjunction with the Alerts page to set up incoming and outgoing e-mail, as well as to set e-mail alerts.
● Alerts : Network only. Allows you to set up to receive e-mail alerts for various device and supplies events.
● AutoSend : Allows you to configure the device to send automated e-mails regarding device configuration and supplies to specific e-mail addresses.
● Security : Allows you to set a password that must be entered to gain access to the
Settings and Networking tabs. Enable and disable certain features of the embedded Web server.
● Authentication Manager : Allows you to determine which device functions will require a user to provide log-in information in order to use those functions.
● LDAP Authentication : Allows you to configure a Lightweight Directory Access
Protocol (LDAP) server to limit device access to certain users. The LDAP server will require a user to provide log-in information in order to gain access to the device.
● Edit Other Links : Allows you to add or customize a link to another Web site. This link is displayed in the Other Links area on all embedded Web server pages.
● Device Information : Allows you to name the device and assign an asset number to it. Enter the name and e-mail address for the primary contact who will receive information about the device.
● Language : Allows you to determine the language in which to display the embedded
Web server information.
● Date & Time : Allows time synchronization with a network time server.
● Wake Time : Allows you to set or edit a wake time for the device.
NOTE: The Settings tab can be password-protected. If this device is on a network, always consult with the system administrator before changing settings on this tab.
180 Chapter 14 Manage and maintain the product ENWW
ENWW
Tab or section
Digital Sending
Fax tab
tab
Networking tab
Provides the ability to change network settings from your computer
Options
Use the pages on the Digital Sending tab to configure the digital-sending features.
NOTE: If the product is configured to use the optional HP Digital Sending Software, the options on these tabs are not available. Instead, all digital-sending configuration is performed by using the HP Digital Sending Software.
● General . Set up contact information for the system administrator.
● Send to E-mail . Configure the e-mail settings for digital sending. You can specify the SMTP server, the default "From" address, and the default subject. You can also set the maximum file size that is allowed for attachments.
● E-mail Address Book . The E-mail Address Book page enables you to add e-mail addresses into the product one at a time, and to edit e-mail addresses that have already been saved in the product. You can also use the Import/Export tab to load a large list of frequently-used e-mail addresses on to the product all at once, rather than adding them one at a time.
● Import/Export . Use this tab to import or export .CSV files containing e-mail addresses, fax numbers, or user records, so that they can be accessed on this product. You can also export e-mail, fax, or user records from the device into a file on your computer. You can then use this file as a data backup, or you can use it to import the records onto another HP device.
● Log . View the digital-sending activity log for the product. The log contains digitalsending job information, including any errors that occur.
● Preferences . Configure digital-sending defaults such as the default page-size and the default settings-reset delay. You can also configure these settings by using the product control-panel menus.
The Fax tab contains options to configure and use the fax capabilities of the product. For additional information about fax functions, see the Fax User Guide.
● Use the Fax Settings screen to configure the send-to-fax features for the product.
● The Fax Address Book page enables you to add fax numbers into the product one at a time, and to edit fax numbers that have already been saved in the product. You can also use the Import/Export feature on the Digital Sending tab to load a large list of frequently-used fax numbers on to the device all at once, rather than adding them one at a time.
● Use the Fax Speed Dials screen to add, edit, or delete fax speed dial entries to and from the product. You can use fax speed dials to store frequently used fax numbers or lists of up to 100 fax numbers. Up to 100 speed dial entries can be configured.
Network administrators can use this tab to control network-related settings for the device when it is connected to an IP-based network. This tab does not appear if the device is directly connected to a computer, or if the device is connected to a network using anything other than an HP Jetdirect print server.
NOTE: The Networking tab can be password-protected.
Embedded Web server 181
Use HP Web Jetadmin software
HP Web Jetadmin is a Web-based software solution for remotely installing, monitoring, and troubleshooting network-connected peripherals. The intuitive browser interface simplifies cross-platform management of a wide range of devices, including HP and non-HP devices. Management is proactive, allowing network administrators the ability to resolve issues before users are affected. Download this free, enhanced-management software at www.hp.com/go/webjetadmin_software .
NOTE: HP Web Jetadmin 10.0 or later is required for full support of this product.
To obtain plug-ins to HP Web Jetadmin, click plug-ins , and then click the download link that is next to the name of the plug-in that you want. The HP Web Jetadmin software can automatically notify you when new plug-ins are available. On the Product Update page, follow the directions to automatically connect to the HP Web site.
If installed on a host server, HP Web Jetadmin is available to any client through a supported Web browser, such as Microsoft Internet Explorer 6.0 for Windows or Netscape Navigator 7.1 for Linux.
Browse to the HP Web Jetadmin host.
NOTE: Browsers must be Java-enabled. Browsing from an Apple PC is not supported.
182 Chapter 14 Manage and maintain the product ENWW
Security features
Secure the embedded Web server
Assign a password for access to the embedded Web server so that unauthorized users cannot change the product settings.
1.
Open the embedded Web server. See
Embedded Web server on page 178 .
2.
Click the Settings tab.
3.
On the left side of the window, click Security .
4.
Type the password next to New Password , and type it again next to Verify Password .
5.
Click Apply . Make note of the password and store it in a safe place.
Secure Disk Erase
To protect deleted data from unauthorized access on the product hard drive, use the Secure Disk Erase feature. This feature can securely erase print and copy jobs from the hard drive.
Secure Disk Erase offers the following levels of disk security:
● Non-Secure Fast Erase . This is a simple file-table erase function. Access to the file is removed, but actual data is retained on the disk until it is overwritten by subsequent data-storage operations.
This is the fastest mode. Non-Secure Fast Erase is the default erase mode.
● Secure Fast Erase . Access to the file is removed, and the data is overwritten with a fixed identical character pattern. This is slower than Non-Secure Fast Erase, but all data is overwritten. Secure
Fast Erase meets the U.S. Department of Defense 5220-22.M requirements for the clearing of disk media.
● Secure Sanitizing Erase . This level is similar to the Secure Fast Erase mode. In addition, data is repetitively overwritten by using an algorithm that prevents any residual data persistence. This mode will impact performance. Secure Sanitizing Erase meets the U.S. Department of Defense
5220-22.M requirements for the sanitization of disk media.
Data affected
Data affected (covered) by the Secure Disk Erase feature includes temporary files that are created during the print and copying process, stored jobs, proof and hold jobs, disk-based fonts, disk-based macros (forms), stored fax files, address books, and HP and third-party applications.
NOTE: Stored jobs will be securely overwritten only when they have been deleted through the
Retrieve Job menu on the product after the appropriate erase mode has been set.
This feature will not impact data that is stored on flash-based product non-volatile RAM (NVRAM) that is used to store default settings, page counts, and similar data. This feature does not affect data that is stored on a system RAM disk (if one is used). This feature does not impact data that is stored on the flash-based system boot RAM.
Changing the Secure Disk Erase mode does not overwrite previous data on the disk, nor does it immediately perform a full-disk sanitization. Changing the Secure Disk Erase mode changes how the product cleans up temporary data for jobs after the erase mode has been changed.
ENWW Security features 183
Gain access to Secure Disk Erase
Use HP Web Jetadmin to gain access to and set the Secure Disk Erase feature.
Additional Information
For additional information about the HP Secure Disk Erase feature, go to www.hp.com/go/ webjetadmin/ .
DSS authentication
Optional Digital Sending Software (DSS) for the product is available for purchase separately. The software provides an advanced sending program that contains an authentication process. This process requires users to type a user identification and a password before they can use any of the DSS features that require authentication.
Lock the control-panel menus
To prevent someone from changing the product configuration, you can lock the control-panel menus.
This prevents unauthorized users from changing the configuration settings such as the SMTP server.
The following procedure describes how to restrict access to the control-panel menus by using the
HP Web Jetadmin software. (See
Use HP Web Jetadmin software on page 182 .)
1.
Open the HP Web Jetadmin program.
2.
Open the DEVICE MANAGEMENT folder in the drop-down list in the Navigation panel. Navigate to the DEVICE LISTS folder.
3.
Select the product.
4.
In the Device Tools drop-down list, select Configure .
5.
Select Security from the Configuration Categories list.
6.
Type a Device Password .
7.
In the Control Panel Access section, select Maximum Lock . This prevents unauthorized users from gaining access to configuration settings.
184 Chapter 14 Manage and maintain the product ENWW
Set the real-time clock
Use the real-time clock feature to set the date and time settings. The date and time information is attached to stored print, fax, and digital-send jobs, so you can identify the most recent versions of stored print jobs.
Set the date format
1.
On the control panel, scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Date/Time .
4.
Touch Date Format .
5.
Touch the desired format.
6.
Touch Save .
Set the date
1.
On the control panel, scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Date/Time .
4.
Touch Date .
5.
Touch the appropriate options to set the correct month, date of the month, and the year.
6.
Touch Save .
Set the time format
1.
On the control panel, scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Date/Time .
4.
Touch Time Format .
5.
Touch the appropriate format.
6.
Touch Save .
Set the time
1.
On the control panel, scroll to and touch Administration .
2.
Touch Time/Scheduling .
3.
Touch Date/Time .
4.
Touch Time .
ENWW Set the real-time clock 185
5.
Touch the appropriate options to set the correct hour, minute, and AM/PM setting.
6.
Touch Save .
186 Chapter 14 Manage and maintain the product ENWW
Manage supplies
Use genuine HP print cartridges for the best printing results.
Print-cartridge storage
Do not remove the print cartridge from its package until you are ready to use it.
CAUTION: To prevent damage to the print cartridge, do not expose it to light for more than a few minutes.
HP policy on non-HP print cartridges
Hewlett-Packard Company cannot recommend the use of non-HP print cartridges, either new or remanufactured. Because they are not HP products, HP cannot influence their design or control their quality.
To install a new HP print cartridge, see
Change print cartridges on page 189 . To recycle the used
cartridge, follow the instructions included with the new cartridge.
HP fraud hotline and Web site
Call the HP fraud hotline (1-877-219-3183, toll-free in North America) or go to www.hp.com/go/ anticounterfeit when you install an HP print cartridge and the control-panel message says the cartridge is non-HP. HP will help determine if the cartridge is genuine and take steps to resolve the problem.
Your print cartridge might not be a genuine HP print cartridge if you notice the following:
● You are experiencing a high number of problems with the print cartridge.
● The cartridge does not look like it usually does (for example, the orange pull tab is missing, or the packaging differs from HP packaging).
ENWW Manage supplies 187
Replace supplies
When you use genuine HP supplies, the product automatically notifies you when supplies are nearly depleted. The notification to order supplies allows ample time to order new supplies before they need to be replaced. For more information about ordering supplies, see
Supplies and accessories on page 273
Locate supplies
Supplies are identified by their labeling and their blue plastic handles.
The following figure illustrates the location of each supply item.
Figure 14-1 Supply item locations
3
2
1
4
5
6
3
4
1
2
5
6
Image drums
Print cartridges
Document feeder kit
Fuser
Transfer unit
Transfer roller
Supply replacement guidelines
To facilitate the replacement of supplies, keep the following guidelines in mind when setting up the product.
● Allow sufficient space in the front and on the right side of the product for removing supplies.
● The product should be located on a flat, sturdy surface.
CAUTION: Hewlett-Packard recommends the use of genuine HP products in this product. Use of non-
HP products may cause problems requiring service that is not covered by the Hewlett-Packard extended warranty or service agreements.
188 Chapter 14 Manage and maintain the product ENWW
Approximate replacement intervals for supplies
The following table lists the estimated replacement intervals for supplies and the control panel messages that prompt when to replace each item. Usage conditions and print patterns may cause results to vary.
Item Printer message Page count Approximate time period
Print cartridges Replace <color> Cartridge
for color 4 months for color
Image drums
Image transfer kit
Image fuser kit
Roller kit
Stapler cartridge
Replace <color> Drum
Replace Transfer Kit
Replace Fuser Kit
Replace Roller Kit
Replace Stapler Cartridge
20,000 pages for black
150,000 pages
100,000 pages
100,000 pages
5000 staples
5 months for black
37 months
25 months
25 months
Booklet maker staple cartridges
Replace Staple Cartridges 2 and 3
2,000 booklets
1
2
Document feeder kit Replace Document Feeder
Kit
60,000 pages 50 months
Approximate average A4-/letter-size page count based on 2-page jobs printed from Tray 2, with 5% coverage of individual colors.
Approximate life is based on 4,000 pages per month.
Change print cartridges
When a print cartridge approaches the end of its useful life, the control panel displays a message recommending that you order a replacement. The product can continue to print using the current print cartridge until the control panel displays a message instructing you to replace the cartridge.
The product uses four colors and has a different print cartridge for each color: black (K), magenta (M), cyan (C), and yellow (Y).
Replace a print cartridge when the control panel displays a Replace <color> Cartridge message. The control panel display will also indicate the color that should be replaced (if a genuine HP cartridge is currently installed). Replacement instructions are included in the print-cartridge box.
CAUTION: If toner gets on clothing, wipe it off with a dry cloth and wash the clothes in cold water. Hot water sets toner into fabric.
NOTE: Information about recycling used print cartridges is on the print-cartridge box.
ENWW Replace supplies 189
Replace print cartridges
1.
Grasp the grips on the sides of the front door and pull down to open.
2.
Grasp the handle of the used print cartridge and pull out to remove.
3.
Store the used print cartridge in a protective bag. Information about recycling used print cartridges is on the print-cartridge box.
4.
Remove additional print cartridges in the same manner.
190 Chapter 14 Manage and maintain the product ENWW
5.
Remove the new print cartridge from its protective bag.
NOTE: Store the protective bag in a secure place for future use.
6.
Hold both sides of the cartridge and shake up and down 5-6 times.
7.
Align the print cartridge with its slot and insert the print cartridge until it clicks into place.
ENWW
8.
Insert additional print cartridges in the same manner.
Replace supplies 191
9.
Grasp the grips on the sides of the front door and lift up to close.
To recycle the used print cartridge, follow the instructions included with the new print cartridge.
Change image drums
When an image drum approaches the end of its useful life, the control panel displays a message recommending that you order a replacement. The product can continue to print using the current image drum until the control panel displays a message instructing you to replace the image drum.
The product uses four colors and has a different image drums for each color: black (K), magenta (M), cyan (C), and yellow (Y).
Replace an image drum when the control panel displays Replace <color> Drum message. The controlpanel display also indicates the color that should be replaced (if a genuine HP cartridge is currently installed). Replacement instructions are included in the image drum box.
CAUTION: If toner gets on clothing, wipe it off with a dry cloth and wash the clothes in cold water. Hot water sets toner into fabric.
NOTE: Information about recycling used image drums is on the image drum box.
192 Chapter 14 Manage and maintain the product ENWW
Replace image drums
1.
Grasp the grips on the sides of the front door and pull down to open.
ENWW
2.
With one hand, lift and slowly pull the used image drum out of the product, while supporting the image drum with your other hand.
CAUTION: If reusing the same image drum, do not touch the green cylinder on the bottom of the drum because it can damage the drum.
3.
Store the used image drum in a protective bag. Information about recycling used image drums is on the image drum box.
4.
Remove additional image drums in the same manner.
Replace supplies 193
5.
Remove the new image drum from its protective bag.
NOTE: Store protective bag in a secure place for future use.
NOTE: Do not shake the image drum.
CAUTION: Do not touch the green cylinder on the bottom of the image drum because it can damage the drum.
6.
Align the image drum with the correct slot and insert the image drum until it clicks into place. The gray protective cover on the bottom of the drum automatically slides off as the image drum is inserted. You can discard this cover.
7.
Insert additional image drums in the same manner.
8.
Grasp the grips on the sides of the front door and lift up to close.
194 Chapter 14 Manage and maintain the product ENWW
To recycle the used image drum, follow the instructions included with the new image drum.
Install memory
You can install more memory for the product.
CAUTION: Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch bare metal on the product.
Install DDR memory DIMMs
1.
Turn the product off.
ENWW
2.
Disconnect all power and interface cables.
Replace supplies 195
3.
Locate the black formatter pressure release tabs on the formatter board in the rear of the product.
4.
Gently press the black tabs toward each other.
5.
Gently pull on the black tabs to pull the formatter board from the product. Place the formatter board on a clean, flat, grounded surface.
196 Chapter 14 Manage and maintain the product ENWW
ENWW
6.
To replace a DIMM that is currently installed, spread the latches apart on each side of the DIMM slot, lift the DIMM up at an angle, and pull it out.
XO
XOXO
XOXO
XO
XOXO
XOXO
XO
XOXO
XOXO
XO
XO
XO
XO
XO
XO
XO
XOXO
XOXO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO XOXOXO
XOXOXOXOXOXO
XOXOXOXOXOXO
XOXO
XOXOXO
7.
Remove the new DIMM from the antistatic package. Locate the alignment notch on the bottom edge of the DIMM.
8.
Holding the DIMM by the edges, align the notch on the DIMM with the bar in the DIMM slot at an angle and firmly press the DIMM into the slot until it is fully seated. When installed correctly, the metal contacts are not visible.
XO
XOXO
XOXO
XO
XOXO
XOXO
XO
XOXO
XOXO
XO XO
XO
XO
XO
XO
XO
XOXO
XOXO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO XOXOXO
XOXOXOXOXOXO
XOXOXOXOXOXO
XOXO
XOXOXO
9.
Push down on the DIMM until both latches engage the DIMM.
XO
XO
XO XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XO
XIO
XIO
XIO
XIO
XIXO
OX
IX
O
XIO
XIO
XIO
XIO
XIXO
OX
IX
O
XIO
XIO
XIO
XIO
XIXO
OX
IX
O
XIO
XIO
XIO
XIO
XIXO
OX
IX O
XO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXOXO
XO
XO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXOXOXOXO
XOXOXOXOXOXO
XOXO
XOXOXO
NOTE: If you have difficulty inserting the DIMM, make sure the notch on the bottom of the DIMM is aligned with the bar in the slot. If the DIMM still does not go in, make sure you are using the correct type of DIMM.
Replace supplies 197
10.
Align the formatter board in the tracks at the bottom of the slot, and then slide the board back into the product.
CAUTION: To prevent damage to the formatter board, ensure the formatter board is aligned in the tracks.
11.
Reconnect the power cable and interface cables, and turn the product on.
12.
To enable the new memory, go to
Enable memory
If you installed a memory DIMM, set the product driver to recognize the newly added memory.
Enable memory for Windows 2000 and XP
1.
On the Start menu, point to Settings , and click Printers or Printers and Faxes .
2.
Right-click the product and select Properties .
3.
On the Device Settings tab, click Printer Memory (in the Installable Options section).
4.
Select the total amount of memory that is now installed.
5.
Click OK .
198 Chapter 14 Manage and maintain the product ENWW
Install an HP Jetdirect or EIO print server card or EIO hard disk
The HP Color LaserJet CM6049f MFP is equipped with an embedded print server port. If desired, you can install an additional I/O card in the available EIO slot.
1.
Turn the product off.
2.
Disconnect all power and interface cables.
ENWW Replace supplies 199
3.
Locate an open EIO slot. Loosen and remove the two retaining screws holding the cover for the
EIO slot, and then remove the cover. You will not need these screws and the cover again. They can be discarded.
4.
Firmly insert the HP Jetdirect print server card into the EIO slot.
5.
Insert and tighten the retaining screws that came with the print server card.
200 Chapter 14 Manage and maintain the product ENWW
6.
Reconnect the power cable and remaining interface cables, and turn the product on.
7.
Print a configuration page. In addition to a product configuration page and a Supplies Status page, an HP Jetdirect configuration page that contains network configuration and status information should also print.
If it does not print, turn the power to the device off and uninstall and reinstall the print server card to ensure that it is completely seated in the slot.
8.
Perform one of these steps:
● Choose the correct port. See the computer or operating system documentation for instructions.
● Reinstall the software, choosing the network installation this time.
Replace the staple cartridge
If the optional HP 3-bin Stapler/Stacker Accessory or HP Booklet Maker/Finisher Accessory runs out of staples while it is stapling a print job, the product automatically stops, if set to stop when out. If the product is set to continue when out, the product will continue to print without stapling.
NOTE: Only replace the staple cartridge unit when the stapler/stacker or booklet maker has run out of staples. Removing the staple cartridge at other times can cause an error to occur.
NOTE: When the stapler/stacker or booklet maker runs out of staples, the stapler unit will return to its default position automatically.
Replace the staple cartridge
1.
Open the front door of the booklet maker or stapler/stacker.
ENWW Replace supplies 201
2.
Push up to on the staple cartridge to remove it from the booklet maker or stapler/stacker.
3.
Insert the replacement staple cartridge unit into the stapler unit.
4.
Push the staple cartridge unit into the stapler unit until it clicks into position.
5.
Close the front door.
202 Chapter 14 Manage and maintain the product ENWW
Replace saddle stitch staple cartridges in the booklet maker
1.
Open the front door of the booklet maker.
2.
Grasp the blue handle and pull the staple carriage out of the booklet maker.
3.
Grasp the small blue handle on the staple cartridge unit and pull it toward you, then swing the staple cartridge unit into an upright position.
2
1
4.
Grasp the edges of each staple cartridge and pull up firmly to remove the staple cartridges from the staple cartridge unit.
ENWW Replace supplies 203
5.
Unpack the new cartridges and remove the plastic packing lock from each one.
6.
Hold the new cartridges so that the arrows on the cartridges align with the arrows on the staple cartridge unit and insert them into the unit.
7.
Pull the handle of the staple cartridge unit toward you and rotate it downward to its original position.
Lock it into position by pushing in the handle.
1
2
8.
Push the staple carriage back into the booklet maker finisher.
204 Chapter 14 Manage and maintain the product ENWW
9.
Close the front door of the booklet maker.
ENWW Replace supplies 205
Clean the product
To maintain print quality, clean the product thoroughly every time you replace the print cartridge and whenever print-quality problems occur.
WARNING!
Avoid touching the fusing area when cleaning the product. It can be hot.
CAUTION: To avoid permanent damage to the print cartridge, do not use ammonia-based cleaners on or around the product except as directed.
Clean the outside of the product
● Clean the outside of the product if it is visibly marked.
● Use a soft, lint-free cloth dampened with water, or water and a mild detergent.
Clean the touchscreen
Clean the touchscreen whenever it is necessary to remove fingerprints or dust. Wipe the touchscreen gently with a clean, water-dampened, lint-free cloth.
CAUTION: Use water only. Solvents or cleaners can damage the touchscreen. Do not pour or spray water directly onto the touchscreen.
Clean the scanner glass
● Clean the scanner glass only if dirt is visible, or if you are experiencing a decrease in copy quality, such as streaking.
● Clean the scanner glass by wiping it gently with a clean, slightly damp, lint-free cloth. Use an ammonia-based surface cleaner only when a water-dampened cloth does not clean the scanner glass.
CAUTION: Do not pour or spray liquids directly onto the scanner glass. Do not press hard on the glass surface. (You could break the glass).
Cleaning the ADF delivery system
Clean the ADF only if it is visibly marked or dirty, or if you are experiencing a decrease in copy quality
(such as streaking).
206 Chapter 14 Manage and maintain the product ENWW
Clean the ADF delivery system
1.
Open the scanner lid.
2.
Locate the white, vinyl ADF backing.
3.
Clean the ADF backing by wiping them with a clean, damp, lint-free cloth. Use an ammonia-based surface cleaner only when a water-dampened cloth does not clean the ADF components.
4.
Clean the scanner glass by wiping it gently with a clean, slightly damp, lint-free cloth. Use an ammonia-based surface cleaner only when a water-dampened cloth does not clean the scanner glass.
5.
Close the scanner lid.
ENWW Clean the product 207
Clean the ADF rollers
You should clean the rollers in the ADF if you are experiencing misfeeds or if your originals show marks as they exit the ADF.
CAUTION: Clean the rollers only if you experience misfeeds or marks on the originals, and you notice dust on the rollers. Cleaning the rollers frequently could introduce dust into the device.
1.
Pull the release lever to open the ADF cover.
2.
Locate the rollers.
3.
Wipe the rollers with a clean, water-dampened, lint-free cloth.
CAUTION: Do not pour water directly onto the rollers. Doing so might damage the device.
4.
Locate the separation pad.
5.
Wipe the pad with a clean, water-dampened, lint-free cloth.
208 Chapter 14 Manage and maintain the product ENWW
6.
Close the ADF cover.
ENWW Clean the product 209
ADF maintenance kit
After feeding 60,000 pages through the ADF, a Replace Document Feeder Kit message appears on the control-panel display. This message appears approximately one month before the kit needs to be replaced. Order a new kit when this message appears. See
for information about ordering a new ADF maintenance kit.
The ADF maintenance kit includes the following items:
● One pick-up roller assembly
● One separation pad
● An instruction sheet
Follow the instructions that come with the kit to install it.
After replacing the kit, reset the ADF maintenance-kit count.
Reset the ADF maintenance-kit count
1.
On the control panel, scroll to and touch Administration .
2.
Touch Resets .
3.
Touch Reset Supplies .
4.
Touch ADF Maintenance Kit .
5.
Touch Yes .
6.
Touch Save .
210 Chapter 14 Manage and maintain the product ENWW
Calibrate the scanner
Calibrate the scanner to compensate for offsets in the scanner imaging system (carriage head) for ADF and flatbed scans. Because of mechanical tolerances, the scanner's carriage head might not read the position of the image accurately. During the calibration procedure, scanner offset values are calculated and stored. The offset values are then used when producing scans so that the correct portion of the document is captured.
Scanner calibration should be carried out only if you notice offset problems with the scanned images.
The scanner is calibrated before it leaves the factory. It needs to be calibrated again only rarely.
Before calibrating the scanner, print the calibration target.
1.
Place letter- or A4-size paper in tray 1, and adjust the side guides.
2.
On the control-panel Home screen, scroll to and touch Administration .
3.
Touch Troubleshooting .
4.
Touch Calibrate Scanner .
5.
Touch Calibrate to print the first pass of the calibration target.
6.
Place the first pass of the calibration target face-down in tray 1 so that the arrows are facing into the product.
7.
Touch Start to print the second pass. The final calibration target must look like the following figure.
CAUTION: If the calibration target does not look like the figure shown here, the calibration process will fail and the quality of scans will be degraded. The black areas must extend completely to the short edges of the page. If they do not, use a black marker to extend the black areas to the edge of the page.
Ensure that the paper is loaded properly.
8.
Place the calibration target face-up into the ADF, and adjust the side guides.
9.
After the calibration target has passed through the ADF once, reposition it face down in the ADF and touch Start .
10.
Place the calibration target face-down on the scanner glass, touch Start , and scan the page. After this pass, the calibration is complete.
ENWW Calibrate the scanner 211
Upgrade the firmware
The product has remote firmware update (RFU) capability. Use the information in this section to upgrade the product firmware.
Determine the current firmware version
1.
From the control panel Home screen, scroll to and touch Administration .
2.
Touch Information .
3.
Touch Configuration/status Pages .
4.
Touch Configuration Page .
5.
Touch Print .
The firmware datecode is listed on the Configuration page in the section called Device Information .
The firmware datecode has this format: YYYYMMDD XX.XXX.X. The first string of numbers is the date, where YYYY represents the year, MM represents the month, and DD represents the date. For example, a firmware datecode of that begins with 20061125 represents November 25, 2006.
Download new firmware from the HP Web site
To find the most recent firmware upgrade for the product, go to www.hp.com/go/ cljcm6049mfp_firmware . This page provides instructions for downloading the new firmware version.
Transfer the new firmware to the product
NOTE: The product can receive an .RFU file update when it is in a "ready" state.
The elapsed time for an update depends on the I/O transfer time, as well as the time that it takes for the product to re-initialize. The I/O transfer time depends on a number of things, including the speed of the host computer that is sending the update. If the remote firmware update process is interrupted before the firmware is downloaded (while Receiving Upgrade appears on the control-panel display), the firmware file must be sent again. If power is lost during the flash DIMM update (while the Performing
Upgrade message appears on the control-panel display), the update is interrupted and the message
Resend Upgrade appears (in English only) on the control-panel display. In this case, you must send the upgrade by using the parallel port. Finally, any jobs that are ahead of the RFU job in the queue are completed before the update is processed.
Use FTP to upload the firmware through a browser
NOTE: The firmware update involves a change in the format of nonvolatile random-access memory
(NVRAM). Any menu settings that are changed from the default settings might return to default settings and must be changed again if you want settings that are different from the defaults.
1.
Print a configuration page and note the TCP/IP address shown on the EIO Jetdirect page.
2.
Open a browser window.
3.
In the address line of the browser, type ftp://<ADDRESS> , where <ADDRESS> is the address of the product. For example, if the TCP/IP address is 192.168.0.90, type ftp://
192.168.0.90
.
212 Chapter 14 Manage and maintain the product ENWW
4.
Locate the downloaded .RFU file for the product.
5.
Drag and drop the .RFU file onto the PORT1 icon in the browser window.
NOTE: The product turns off and then on automatically to activate the update. When the update process is complete, a Ready message displays on the product control panel.
Use FTP to upgrade the firmware on a network connection
NOTE: The firmware update involves a change in the format of nonvolatile random-access memory
(NVRAM). Any menu settings that are changed from the default settings might return to default settings and must be changed again if you want settings that are different from the defaults.
1.
Take note of the IP address on the HP Jetdirect page. The HP Jetdirect page is the second page that prints when you print the configuration page.
NOTE: Before upgrading the firmware, make sure that the product is not in Sleep mode. Also make sure that any error messages are cleared from the control-panel display.
2.
Open an MS-DOS command prompt on your computer.
3.
Type: ftp TCP/IP ADDRESS> . For example, if the TCP/IP address is 192.168.0.90, type ftp
192.168.0.90
.
4.
Go to the folder where the firmware file is stored.
5.
Press Enter on the keyboard.
6.
When prompted for the user name, press Enter .
7.
When prompted for the password, press Enter .
8.
Type bin at the command prompt.
9.
Press Enter . The message 200 Types set to I, Using binary mode to transfer files appears in the command window.
10.
Type put and then the file name (for example, if the file name is CM6049fmfp.efn, type put
CM6049fmfp.efn
).
11.
The download process begins and the firmware is updated on the product. This can take approximately five minutes. Let the process finish without further interaction with the product or computer.
NOTE: The product automatically turns off and then on again after processing the upgrade.
12.
At the command prompt, type: bye to exit the ftp command.
13.
At the command prompt, type: exit to return to the Windows interface.
ENWW Upgrade the firmware 213
Use HP Web Jetadmin to upgrade the firmware
This procedure requires that you install HP Web Jetadmin Version 7.0 or later on your computer. See
Use HP Web Jetadmin software on page 182 . Complete the following steps to update a single device
through HP Web Jetadmin after downloading the .RFU file from the HP Web site.
1.
Start HP Web Jetadmin.
2.
Open the Device Management folder in the drop-down list in the Navigation panel. Navigate to the Device Lists folder.
3.
Expand the Device Lists folder and select All Devices . Locate the product in the list of devices, and then click to select it.
If you need to upgrade the firmware for multiple HP Color LaserJet CM6049f MFP products, select all of them by pressing the Ctrl key as you click the name of each product.
4.
Locate the drop-down box for Device Tools in the upper-right corner of the window. Select Update
Printer Firmware from the action list.
5.
If the name of the .RFU file is not listed in the All Available Images box, click Browse in the
Upload New Firmware Image dialog box and navigate to the location of the .RFU file that you downloaded from the Web at the start of this procedure. If the filename is listed, select it.
6.
Click Upload to move the .RFU file from your hard drive to the HP Web Jetadmin server. After the upload is complete, the browser window refreshes.
7.
Select the .RFU file from the Printer Firmware Update drop-down menu.
8.
Click Update Firmware . HP Web Jetadmin sends the selected .RFU file to the product. The control panel shows messages that indicate the progress of the upgrade. At the end of the upgrade process, the control panel shows the Ready message.
Use MS-DOS commands to upgrade the firmware
To update the firmware by using a network connection, follow these instructions.
1.
From a command prompt or in an MS-DOS window, type the following: copy /B FILENAME> \
\COMPUTERNAME>\SHARENAME> , where <FILENAME> is the name of the .RFU file (including the path), <COMPUTERNAME> is the name of the computer from which the product is being shared, and <SHARENAME> is the product share name. For example: C:\>copy /b C:\9200fW.RFU
\\YOUR_SERVER\YOUR_COMPUTER .
NOTE: If the file name or path includes a space, you must enclose the file name or path in quotation marks. For example, type: C:\>copy /b "C:\MY DOCUMENTS\3500FW.RFU" \
\YOUR_SERVER\YOUR_COMPUTER .
2.
Press Enter on the keyboard. The control panel shows a message that indicates the progress of the firmware upgrade. At the end of the upgrade process, the control panel shows the Ready message . The message One File Copied appears on the computer screen.
Use the HP Jetdirect firmware
The HP Jetdirect network interface in the product has firmware that can be upgraded separately from the product firmware. This procedure requires that you install HP Web Jetadmin Version 7.0 or later on
214 Chapter 14 Manage and maintain the product ENWW
ENWW
your computer. See Use HP Web Jetadmin software on page 182
. Complete the following steps to update the HP Jetdirect firmware by using HP Web Jetadmin.
1.
Open the HP Web Jetadmin program.
2.
Open the Device Management folder in the drop-down list in the Navigation panel. Navigate to the Device Lists folder.
3.
Select the device that you want to update.
4.
In the Device Tools drop-down list, select Jetdirect Firmware Update .
5.
Under Jetdirect firmware version the HP Jetdirect model number and current firmware version are listed. Make a note of these.
6.
Go to www.hp.com/go/wja_firmware .
7.
Scroll down to the list of HP Jetdirect model numbers and find the model number you wrote down.
8.
Look at the current firmware version for the model, and see if it is later than the version you wrote down. If it is, right-click on the firmware link, and follow the instructions on the Web page to download the new firmware file. The file must be saved into the <drive>:\PROGRAM FILES
\HP WEB JETADMIN\DOC\PLUGINS\HPWJA\FIRMWARE\JETDIRECT folder on the computer that is running the HP Web Jetadmin software.
9.
In HP Web Jetadmin, return to the main device list and select the digital sender again.
10.
In the Device Tools drop-down list, select Jetdirect Firmware Update again.
11.
On the HP Jetdirect firmware page, the new firmware version is listed under Jetdirect Firmware
Available on HP Web Jetadmin . Click the Update Firmware Now button to update the Jetdirect firmware.
Upgrade the firmware 215
216 Chapter 14 Manage and maintain the product ENWW
15 Solve problems
●
●
●
●
●
●
Understand lights on the formatter
●
Correct print quality and copy quality problems
●
●
●
●
Solve network connectivity problems
●
Solve common Macintosh problems
ENWW 217
Solving general problems
If the product is not responding properly, complete the steps in the following checklist, in order. If the product does not pass a step, follow the corresponding troubleshooting suggestions. If a step resolves the problem, you can stop without performing the other steps on the checklist.
Troubleshooting checklist
1.
Make sure the product Ready light is on. If no lights are on, complete these steps: a.
Check the power-cable connections.
b.
Check that the power switch is on.
c.
Make sure that the line voltage is correct for the product power configuration. (See the label that is on the back of the product for voltage requirements.) If you are using a power strip and its voltage is not within specifications, plug the product directly into the wall. If it is already plugged into the wall, try a different outlet.
d.
Remove any other products plugged into the same circuit.
e.
If none of these measures restores power, contact your dealer for support.
2.
Check the cabling.
a.
Check the cable connection between the product and the computer or network port. Make sure that the connection is secure.
b.
Make sure that the cable itself is not faulty by using a different cable, if possible.
c.
Check the network connection. See
Solve network printing problems on page 268 .
3.
If the product is in the READY state, check to see if any message appear on the control-panel display. If any error messages appear, see
Control-panel messages on page 221
.
4.
Ensure that the print paper that you are using meets specifications.
5.
Print a configuration page (see
Information pages on page 176 . An HP Jetdirect page also prints.)
a.
If the pages do not print, check that at least one tray contains print paper.
b.
If the page jams in the product, see Jams on page 222
.
6.
If the configuration page prints, check the following items.
a.
If the page prints correctly, then the product hardware is working. The problem is with the computer you are using, with the printer driver, or with the program.
b.
If the page does not print correctly, the problem is with the product hardware. Contact your dealer for support.
7.
Select one of the following options:
Windows : Click Start , click Settings , and then click Printers , or Printers and Faxes . Double click
HP Color LaserJet CM6049f .
-or-
218 Chapter 15 Solve problems ENWW
Mac OS X : Open Print Center , (or Printer Setup Utility for Mac OS X v. 10.3), and double-click the line for the HP Color LaserJet CM6049f .
8.
Verify that you have installed the HP Color LaserJet CM6049f printer driver. Check the program to make sure that you are using an HP Color LaserJet CM6049f printer driver.
9.
Print a short document from a different program that has worked in the past. If this solution works, then the problem is with the program you are using. If this solution does not work (the document does not print) complete these steps: a.
Try printing the job from another computer that has the product software installed.
b.
If you connected the product to the network, connect the product directly to a computer with a USB cable. Redirect the product to the correct port, or reinstall the software, selecting the new connection type that you are using.
Restore factory settings
Use the Resets menu to restore factory settings.
1.
Scroll to and touch Administration and then touch Resets .
2.
Touch Restore Factory Settings and then touch Restore .
For more information, see Resets menu on page 58 .
Factors that affect product performance
Several factors affect the time it takes to print a job:
● Maximum printer speed, measured in pages per minute (ppm)
● The use of special paper (such as transparencies, heavy paper, and custom-size paper)
● Printer processing and download time
● The complexity and size of graphics
● The speed of the computer you are using
● The USB connection
● The printer I/O configuration
● The amount of printer memory installed
● The network operating system and configuration (if applicable)
● Printer personality (HP JetReady, PCL, or PS)
NOTE: Although additional printer memory can resolve memory problems, improve how the printer handles complex graphics, and improve download times, it will not increase maximum printer speed
(ppm).
ENWW Solving general problems 219
Control-panel message types
Four types of control-panel messages can indicate the status of or problems with the device.
Message type
Status messages
Warning messages
Error messages
Description
Status messages reflect the current state of the device. They inform you of normal device operation and require no interaction to clear them. They change as the state of the device changes. Whenever the device is ready, not busy, and has no pending warning messages, the status message Ready appears if the device is online.
Warning messages inform you of data and print errors. These messages typically alternate with the
Ready or status messages and remain until you touch OK . Some warning messages are clearable.
If Clearable Warnings is set to Job on the device Device Behavior menu, the next print job clears these messages.
Error messages communicate that some action must be performed, such as adding paper or clearing a jam.
Some error messages are auto-continuable. If Auto-Continue is set on the menus, the device will continue normal operation after an auto-continuable error message appears for 10 seconds.
NOTE: Pressing any button during the 10-second auto-continuable error message overrides the auto-continue feature, and the button function takes precedence. For example, pressing the Stop button pauses printing and offers the option to cancel the print job.
Critical-error messages Critical error messages inform you of a device failure. Some of these messages can be cleared by turning the device off and then on. These messages are not affected by the Auto-Continue setting.
If a critical error persists, service is required.
220 Chapter 15 Solve problems ENWW
Control-panel messages
The product provides robust control panel messaging. When a message appears on the control panel, follow the on-screen instructions to resolve the issue. If the product displays an “Error” or “Attention” message, and no steps are shown to resolve the issue, turn the product off then on. Contact your dealer for support if you continue to experience issues with the product.
To get additional information for warnings that appear in the status line, touch the Warning button
.
For additional information on a variety of topics, touch the Help button in the upper-right corner of the home screen.
ENWW Control-panel messages 221
Jams
Common causes of jams
The product is jammed.
Cause Solution
The paper does not meet specifications.
A component is installed incorrectly.
Use only paper that meets HP specifications. See
Supported paper and print media sizes on page 95
.
Verify that the transfer belt and transfer roller are correctly installed.
You are using paper that has already passed through a product or copier.
Do not use paper that has been previously printed on or copied.
An input tray is loaded incorrectly.
The paper is skewed.
Remove any excess paper from the input tray. Make sure that the stack is below the maximum stack height mark in the tray.
See Load paper and print media on page 101 .
The input-tray guides are not adjusted correctly. Adjust them so they hold the stack firmly in place without bending it.
The paper is binding or sticking together.
When printing on lightweight paper or on jobs with heavy toner coverage, paper is wrapping on the fuser causing Fuser Delay
Jam or Fuser Wrap Jam messages.
Set the LIGHT MEDIA optimize mode on the Print Quality menu to ON .
The paper is removed before it settles into the output bin.
Remove the paper, flex it, rotate it 180°, or flip it over. Reload the paper into the input tray.
During two-sided printing, you removed the paper before the second side of the document was printed.
Reset the product. Wait until the page completely settles in the output bin before removing it.
Reset the product and print the document again. Wait until the page completely settles in the output bin before removing it.
The paper is in poor condition.
The internal tray rollers are not picking up the paper.
Replace the paper.
If the paper is heavier than 220 g/m 2 (58 lb), it might not be picked from the tray.
The paper has rough or jagged edges.
The paper is perforated or embossed.
The rollers are worn. Replace the rollers.
Replace the paper.
Device supply items have reached the end of their useful life.
Check the product control panel for messages prompting you to replace supplies, or print a supplies status page to verify the
remaining life of the supplies. See Information pages on page 176
.
Paper was not stored correctly.
Perforated or embossed paper does not separate easily. Feed single sheets from Tray 1.
Not all product packing material was removed.
Replace the paper in the trays. Paper should be stored in the original packaging in a controlled environment.
Verify that the packing tape, cardboard, and plastic shipping locks have been removed from the product.
If the product still continues to jam, contact your dealer for support.
222 Chapter 15 Solve problems ENWW
Jam locations
Use this illustration to identify locations of jams. In addition, this product provides instructions on the control panel to direct you to the location of jammed paper and how to clear it.
NOTE: All areas of the product that might need to be opened to clear jams are equipped with green handles.
Figure 15-1 Jam locations
3
4
5
1
2
8
9
6
7
AREA 1: Output bin
AREA 2: Fuser area
AREA 3: Transfer area
AREA 4: Duplexing area
AREA 5: Tray 2 pickup area
AREA 6: Tray 1 area
AREA 7: Optional Trays 3, 4, and 5
AREA 8: Optional finishing device
AREA 9: ADF area
Clear jams
When a jam occurs, a message appears on the control-panel display that describes the location of the jam. The following table lists the messages that can appear and provides links to the procedures for clearing the jam.
ENWW Jams 223
WARNING!
To avoid electrical shock, remove any necklaces, bracelets, or other metal items before reaching into the inside of the product.
Type of jam
13.JJ.NT Jam below control panel
Procedure
See AREA 1: Clear jams in the output bin on page 224
.
13.JJ.NT Fuser Area Jam
13.JJ.NT Fuser Wrap Jam
13.JJ.NT Transfer And Fuser Jam
13.JJ.NT Jam Inside Right Door
13.JJ.NT Jam In Tray 2
13.JJ.NT Transfer Area Jam
13.JJ.NT Jam In Tray 1
13.JJ.NT Jam In Tray 3
13.JJ.NT Jam In Tray 4
13.JJ.NT Jam In Tray 5
13.JJ.NT Jam Inside Lower Right Door
13.JJ.NT Jam In Input Accessory
13.JJ.NT Jam In Left Accessory
Jam in document feeder
See AREA 2: Clear jams in the fuser on page 226 .
See Clear jams in the duplex area on page 230 .
See AREA 5: Clear jams in Tray 2 and the internal paper path on page 233
.
See AREA 6: Clear jams in Tray 1 on page 236 .
See AREA 7: Clear jams in optional Trays 3, 4, and 5 on page 239
See AREA 8: Clear jams in the optional finishing devices on page 242
.
See AREA 9: Clear jams in the ADF on page 246
.
AREA 1: Clear jams in the output bin
1.
If jammed paper is visible in the output bin, gently pull the paper to remove it.
224 Chapter 15 Solve problems ENWW
ENWW
2.
Open the right door.
3.
If paper has jammed as it enters the output bin, gently pull the paper to remove it.
4.
Close the right door.
Jams 225
AREA 2: Clear jams in the fuser
WARNING!
The fuser can be hot while the product is in use. Wait for the fuser to cool before handling it.
1.
Open the right door.
2.
Lift the green handle on the transfer-access panel and open the panel.
1
2
3.
If paper is visible entering the bottom of the fuser, gently pull downward to remove it.
226 Chapter 15 Solve problems ENWW
ENWW
4.
Close the transfer-access panel.
5.
Open the fuser jam access door above the fuser and remove any paper that is visible. Then close the fuser jam access door.
6.
Paper could also be jammed inside the fuser where it would not be visible. Remove the fuser to check for jammed paper inside.
WARNING!
The fuser can be hot while the product is in use. Wait for the fuser to cool before handling it.
a.
Pull the two blue fuser handles forward.
Jams 227
b.
Rotate the fuser-release levers down to open them.
c.
Grasp the fuser handles and pull straight out to remove the fuser.
CAUTION: The fuser weighs 5 kg (11 lbs). Be careful not to drop it.
d.
Open the two fuser jam access doors by pushing and rotating the rear door backward, and pulling and rotating the front door forward. If paper is jammed inside the fuser, gently pull it straight up to remove it. If the paper tears, remove all paper fragments.
WARNING!
Even if the body of the fuser has cooled, the rollers that are inside could still be hot. Do not touch the fuser rollers until they have cooled.
2
1
228 Chapter 15 Solve problems ENWW
ENWW e.
Close both fuser jam-access doors and align the fuser with the arrows on the product. Push the fuser completely into the printer.
f.
Rotate the fuser-release levers up to lock the fuser into place.
g.
Push the fuser handles back to close them.
Jams 229
7.
Close the right door.
Clear jams in the duplex area
1.
Check for jammed paper inside the product. Open the right door.
230 Chapter 15 Solve problems ENWW
ENWW
2.
If paper is jammed below the duplexing unit, gently pull the paper downward to remove it.
3.
If paper is jammed inside the right door, gently pull the paper to remove it.
Jams 231
4.
Lift the paper-feed cover on the inside of the right door. If jammed paper is present, gently pull the paper straight out to remove it.
2
5.
Lift the green handle on the transfer-assembly and open the panel.
1
1
2
6.
Gently pull the paper out of the paper path.
232 Chapter 15 Solve problems ENWW
7.
Close the transfer-access panel.
8.
Close the right door.
AREA 5: Clear jams in Tray 2 and the internal paper path
1.
Open the right door.
ENWW Jams 233
2.
Lift the green handle on the transfer-access panel and open the panel.
1
2
3.
Gently pull the paper out of the paper path.
4.
Close the transfer-access panel.
234 Chapter 15 Solve problems ENWW
ENWW
5.
Open Tray 2 and make sure that the paper is stacked correctly.
6.
Pull the tray completely out of the product by pulling and lifting it up slightly.
7.
Remove any paper from the feeder rollers inside the product.
8.
Reinsert Tray 2 by aligning the side rollers and pushing it back into the product.
Jams 235
9.
Close the tray.
10.
Close the right door.
AREA 6: Clear jams in Tray 1
NOTE: Even if jammed paper is visible in Tray 1, clear the jam from the inside of the product by opening the right door.
236 Chapter 15 Solve problems ENWW
ENWW
1.
Open the right door.
NOTE: When clearing jams of long paper (11 x 17, 12 x 18, and A3), it may be necessary to cut or tear the jammed paper before opening the right door.
2.
If paper is visible inside the right door, gently pull the paper downward to remove it.
Jams 237
3.
If paper has entered the internal paper path, lift the green handle on the transfer-access panel and open the panel.
1
2
4.
Gently pull the paper out of the paper path.
5.
Close the transfer-access panel.
238 Chapter 15 Solve problems ENWW
6.
Close the right door.
AREA 7: Clear jams in optional Trays 3, 4, and 5
1.
Open the right door.
ENWW
2.
If paper is visible in the paper-input area, gently pull the jammed paper up to remove it.
Jams 239
3.
Close the right door.
4.
Open the lower right door.
5.
Gently pull the jammed paper to remove it.
240 Chapter 15 Solve problems ENWW
ENWW
6.
Open the tray that is indicated in the control-panel message, and make sure that the paper is stacked correctly.
7.
Close the tray.
8.
Close the lower right door.
Jams 241
AREA 8: Clear jams in the optional finishing devices
Clear jams in the output-accessory bridge
1.
Lift the latch on the top cover of the output-accessory bridge and open the top cover.
2.
Gently pull the jammed paper to remove it.
3.
Close the top cover of the output-accessory bridge.
242 Chapter 15 Solve problems ENWW
Clear jams in the sorter area
1.
Lift the latch on the top cover of the finishing device, and open the top cover.
NOTE: Opening the top cover releases pressure on the output-bin rollers.
2.
Remove jammed paper from the output bin or from the inside of the finishing device.
2
3
1
ENWW
3.
Close the top cover of the finishing device.
Jams 243
4.
Lift the swing guide panel in the output bin. If you can see any jammed paper, gently pull it out.
Clear jams in the booklet maker
1.
If the paper is visible in the booklet output bin, gently pull the paper to remove it.
2.
Open the front door of the booklet maker.
3.
Push the upper delivery guide to the right, and remove any jammed paper.
1
2
244 Chapter 15 Solve problems ENWW
ENWW
4.
Push the lower delivery guide to the right, and remove any jammed paper.
2
1
5.
The positioning knob is the smaller, green dial on the right. Turn the positioning knob counterclockwise.
6.
The jam-release knob is the larger, green dial on the left. Push in the jam-release knob, and then turn it clockwise to move any jammed paper into the output bin.
7.
Close the front door of the booklet maker.
Jams 245
AREA 9: Clear jams in the ADF
1.
Open the ADF cover.
2.
Remove any jammed media.
3.
Close the ADF cover.
246 Chapter 15 Solve problems ENWW
Clear staple jams
Clear staple jams in the main stapler
The HP 3-bin Stapler/Stacker and the HP Booklet maker/Finisher Accessory each have a main stapler, which is located near the top of the finishing device.
1.
Open the front door of the finishing device.
2.
To remove the staple cartridge, pull up on the green handle and pull out the staple cartridge.
3.
Lift up on the small lever at the back of the staple cartridge.
4.
Remove the damaged staples that protrude from the staple cartridge. Remove the entire sheet of staples that the damaged staples were attached to.
ENWW Jams 247
5.
Close the lever at the back of the staple cartridge. Be sure that it snaps into place.
6.
Reinsert the staple cartridge into the finishing device, and push down on the green handle until it snaps into place.
7.
Close the front cover of the finishing device.
Clear staple jams in the booklet maker
The booklet maker has an additional saddle stitch stapler that is below the main stapler. The saddle stitch stapler has two staple cartridges.
1.
Open the front door of the booklet maker.
248 Chapter 15 Solve problems ENWW
ENWW
2.
Push the upper delivery guide to the right, and remove any jammed paper.
1
2
3.
Grasp the blue handle for the stapler carriage and pull it straight out.
4.
Grasp the handle of the blue staple cartridge unit and pull it toward you, then swing the staple cartridge unit into an upright position.
2
1
Jams 249
5.
Check each staple cartridge for jammed staples.
a.
On each staple cartridge, press down on the green plastic tabs while lifting the jam clearance plate.
WARNING!
Do not place your fingers or hands underneath the staple cartridge during this procedure.
1
2
3 b.
Remove any jammed staples. Remove any damaged staples and the entire sheet of staples that the damaged staples were attached to.
c.
Press down on the jam clearance plate to close it.
WARNING!
Do not place your fingers or hands underneath the staple cartridge during this procedure.
6.
Pull the staple cartridge unit forward, and swing it downward to the original position. Push in on the handle to lock it into position.
1
2
250 Chapter 15 Solve problems ENWW
7.
Push the staple carriage back into the booklet maker.
8.
Close the front door of the booklet maker.
Jam recovery
This product provides jam recovery, a feature that reprints jammed pages. The following options are available:
● Auto — The product attempts to reprint jammed pages when sufficient memory is available.
● Off — The product does not attempt to reprint jammed pages. Because no memory is used to store the most recent pages, performance is optimal.
NOTE: When using this option, if the product runs out of paper and the job is being printed on both sides, some pages can be lost.
● On — The product always reprints jammed pages. Additional memory is allocated to store the last few pages printed. This might cause overall performance to suffer.
Set the jam recovery feature
1.
Touch Administration and then touch Device Behavior .
2.
Touch Warning/Error Behavior and then touch Jam Recovery .
3.
Touch an option and then touch Save .
ENWW Jams 251
Paper-handling problems
Use only paper that meets the specifications outlined in the HP LaserJet Printer Family Print Media
Guide . This guide is available at www.hp.com/support/ljpaperguide .
Product feeds multiple sheets
Product feeds multiple sheets
Cause
The input tray is overfilled. Open the tray and verify that the paper stack is below the maximum stack height mark.
Print paper is sticking together.
Paper does not meet the specifications for this product.
Trays are not properly adjusted.
Solution
Remove excess paper from the input tray.
Remove paper, flex it, rotate it 180 degrees or flip it over, and then reload it into the tray.
NOTE: Do not fan paper. Fanning can cause static electricity, which can cause paper to stick together.
Use only paper that meets HP paper specifications for this product.
Make sure that the paper guides match the size of paper being used.
Product feeds incorrect page size
Product feeds incorrect page size
Cause Solution
The correct size paper is not loaded in the input tray.
Load the correct size paper in the input tray.
The correct size paper is not selected in the software program or printer driver.
Confirm that the settings in the software program and printer driver are appropriate, since the software program settings override the printer driver and control panel settings, and the printer driver settings override the control panel settings. For
more information, see Change printer-driver settings for
Change printer-driver settings for
The correct size paper for the tray is not selected in the product control panel.
From the control panel, select the correct size paper for the tray.
The paper size is not configured correctly for the input tray.
The guides in the tray are not against the paper.
Print a configuration page or use the control panel to determine the paper size for which the tray is configured.
Verify that the paper guides are touching the paper.
Product pulls from incorrect tray
Product pulls from incorrect tray
Cause
You are using a driver for a different product.
The specified tray is empty.
Solution
Use a driver for this product.
Load paper in the specified tray.
252 Chapter 15 Solve problems ENWW
Product pulls from incorrect tray
Cause
The paper size is not configured correctly for the input tray.
The guides in the tray are not against the paper.
Solution
Print a configuration page or use the control panel to determine the paper size for which the tray is configured.
Verify that the guides are touching the paper.
Paper does not feed automatically
Paper does not feed automatically
Cause Solution
Manual feed is selected in the software program.
Load Tray 1 with paper, or, if the paper is loaded, press the
Start button.
The correct size paper is not loaded.
The input tray is empty.
Load the correct size paper.
Load paper into the input tray.
Paper from a previous jam has not been completely removed. Open the product and remove any paper in the paper path.
The paper size is not configured correctly for the input tray.
Print a configuration page or use the control panel to determine the paper size for which the tray is configured.
The guides in the tray are not against the paper.
Verify that the rear and width paper guides are touching the paper.
Open the tray, reload the media, and then close the tray.
The manual-feed prompt is set to ALWAYS . The product always prompts for manual feed, even if the tray is loaded.
Or, change the manual-feed prompt setting to UNLESS
LOADED , so that the product prompts for manual feed only when the tray is empty.
The USE REQUESTED TRAY setting on the product is set to
EXCLUSIVELY , and the requested tray is empty. The product will not use another tray.
Load the requested tray.
Or, change the setting from EXCLUSIVELY
CONFIGURE DEVICE menu. The product can use other trays if no media is loaded in the specified tray.
to FIRST on the
Paper does not feed from Tray 2, 3, 4, or 5
Paper does not feed from Tray 2, 3, 4, or 5
Cause Solution
The correct size paper is not loaded.
The input tray is empty.
Load the correct size paper.
Load paper in the input tray.
The correct paper type for the input tray is not selected in the product control panel.
From the product control panel, select the correct paper type for the input tray.
Paper from a previous jam has not been completely removed. Open the product and remove any paper in the paper path.
Closely inspect the fuser area for jams.
ENWW Paper-handling problems 253
Paper does not feed from Tray 2, 3, 4, or 5
Cause
None of the optional trays appear as input tray options.
An optional tray is incorrectly installed.
The paper size is not configured correctly for the input tray.
The guides in the tray are not against the paper.
Solution
The optional trays only display as available if they are installed.
Verify that any optional trays are correctly installed. Verify that the printer driver has been configured to recognize the optional trays.
Print a configuration page to confirm that the optional tray is installed. If not, verify that the tray is correctly attached to the product.
Print a configuration page or use the control panel to determine the paper size for which the tray is configured.
Verify that the guides are touching the paper.
Transparencies or glossy paper will not feed
Transparencies or glossy paper will not feed
Cause Solution
The correct paper type is not specified in the software or printer driver.
Verify that the correct paper type is selected in the software or printer driver.
The input tray is overfilled.
Remove excess paper from the input tray. Do not load more than 200 sheets of glossy paper or glossy film, or more than
100 transparencies in Tray 2, 3, 4, or 5. Do not exceed the maximum stack height marks for Tray 1.
Paper in another input tray is the same size as the transparencies, and the product is defaulting to the other tray.
Make sure that the input tray containing the transparencies or glossy paper is selected in the software program or printer driver. Use the product control panel to configure the tray to the paper type loaded.
The tray containing the transparencies or glossy paper is not configured correctly for type.
Make sure that the input tray containing the transparencies or glossy paper is selected in the software program or printer driver. Use the product control panel to configure the tray to the paper type loaded.
Transparencies or glossy paper might not meet supported paper specifications.
High-humidity environments may cause glossy paper not to feed, or to feed too many sheets.
Use only paper that meets the HP paper specifications for this product.
Print glossy paper from Tray 2, 3, 4, or 5 for best results.
Avoid printing glossy paper in high humidity conditions. When printing glossy paper, removing the paper from the wrapper and letting it rest for a few hours can improve feeding into the product. However, letting paper rest in humid environments may also cause blisters.
CAUTION: HP Color Laser Presentation Paper, Glossy (Q2546A) is not supported with this product.
Using this type of paper can cause a fuser jam that might require the replacement of the fuser. Two recommended alternatives are HP Color LaserJet Presentation Paper, Soft Gloss (Q6541A) and
HP Color LaserJet Brochure Paper, Glossy (Q6611A, Q6610A). For a list of supported paper types, see
Supported paper types on page 98 .
254 Chapter 15 Solve problems ENWW
Envelopes jam or will not feed in the product
Envelopes jam or will not feed in the product
Cause Solution
Envelopes are loaded in an unsupported tray. Only Tray 1 can feed envelopes.
Load envelopes into Tray 1.
Envelopes are curled or damaged.
Envelopes are sealing because the moisture content is too high.
Try using different envelopes. Store envelopes in a controlled environment.
Try using different envelopes. Store envelopes in a controlled environment.
Envelope orientation is incorrect.
This product does not support the envelopes being used.
Tray 1 is configured for a size other than envelopes.
Verify that the envelope is loaded correctly.
Refer to the HP LaserJet Printer Family Print Media Guide
Configure Tray 1 size for envelopes.
.
Output is curled or wrinkled
Output is curled or wrinkled
Cause Solution
Paper does not meet the specifications for this product.
Paper is damaged or in poor condition.
Product speed needs to be reduced.
Product is operating in an excessively humid environment.
You are printing large, solid-filled areas.
Use only paper that meets the HP paper specifications for this product.
Remove paper from the input tray and load paper that is in good condition.
Set the PAPER CURL option in the Print Quality menu to
REDUCED to decrease full speed to 10 ppm (instead of 40 ppm) and 3/4 speed to 7.5 ppm (instead of 30 ppm).
Verify that the printing environment is within humidity specifications.
Large, solid-filled areas can cause excessive curl. Try using a different pattern.
Paper used was not stored correctly and might have absorbed moisture.
Remove paper and replace it with paper from a fresh, unopened package.
Paper has poorly cut edges.
Remove paper, flex it, rotate it 180 degrees or turn it over, and then reload it into the input tray. Do not fan paper. If the problem persists, replace the paper.
The specific paper type was not configured for the tray or selected in the software.
The paper has previously been used for a print job.
Configure the software for the paper (see the software documentation). Configure the tray for the paper, see
paper and print media on page 101
.
Do not re-use paper.
ENWW Paper-handling problems 255
Product will not duplex or duplexes incorrectly
Product will not duplex (print 2-sided jobs) or duplexes incorrectly
Cause Solution
You are trying to duplex on unsupported paper.
The printer driver is not set up for duplex printing.
The first page is printing on the back of preprinted forms or letterhead.
The product model does not support automatic 2-sided printing.
The product configuration is not set for duplexing.
Verify that the paper is supported for duplex printing.
Set up the printer driver to enable duplex printing.
Load preprinted forms and letterhead in Tray 1 with the letterhead or printed side down, with the top of the page toward the back of the product. For Tray 2, 3, 4 and 5, load the paper printed side up with the top of the page toward the back of the product.
The HP Color LaserJet CM6049f MFP does not support automatic 2-sided printing.
In Windows, run the automatic configuration feature:
1.
Click the Start button, point to Settings , and then click
Printers (for Windows 2000) or Printers and Faxes (for
Windows XP).
2.
Right-click the HP product icon, and then click
Properties or Printing Preferences .
3.
Click the Device Settings tab.
4.
Under Installable Options , click Update Now in the
Automatic Configuration list.
256 Chapter 15 Solve problems ENWW
Understand lights on the formatter
Three LEDs on the formatter indicate that the product is functioning correctly.
1
2
1
2
Heartbeat LED
HP Jetdirect LEDs (This LED exists only if HP Jetdirect is installed.)
HP Jetdirect LEDs
The embedded HP Jetdirect print server has two LEDs. The yellow LED indicates network activity, and the green LED indicates the link status. A blinking yellow LED indicates network traffic. If the green LED is off, a link has failed.
For link failures, check all of the network cable connections. In addition, you can try to manually configure the link settings on the embedded print server by using the product control-panel menus.
1.
Scroll to and touch Administration .
2.
Touch Initial Setup .
3.
Touch Networking and I/O .
4.
Touch Embedded Jetdirect or EIO <X> Jetdirect .
5.
Touch Link Speed .
6.
Select the appropriate link speed.
7.
Touch Save .
Heartbeat LED
The heartbeat LED indicates that the formatter is functioning correctly. While the product is initializing after you turn it on, the LED blinks rapidly, and then turns off. When the product has finished the initialization sequence, the heartbeat LED pulses on and off.
If the heartbeat LED is off, the formatter might have a problem. Replace or reseat the formatter.
ENWW Understand lights on the formatter 257
Correct print quality and copy quality problems
The following procedures help you define print quality problems and what to do to correct them. Often print quality problems can be handled easily by making sure that the product is properly maintained, using print media that meets HP specifications, or running a cleaning page.
Example print quality problems
Some print quality problems arise from use of inappropriate paper.
● Use paper that meets HP paper specifications.
● The surface of the paper is too rough. Use paper that meets HP paper specifications.
● The printer driver setting or paper tray setting might be incorrect. Be sure that you have configured the paper tray at the product control panel and have also selected the correct driver setting for the paper that you are using.
● The print mode might be set incorrectly, or the paper might not meet recommended specifications.
● The transparencies you are using are not designed for proper toner adhesion. Use only transparencies designed for HP Color LaserJet products.
● The moisture content of the paper is uneven, too high, or too low. Use paper from a different source or from an unopened ream of paper.
● Some areas of the paper reject toner. Use paper from a different source or from an unopened ream of paper.
● The letterhead you are using is printed on rough paper. Use a smoother, xerographic paper. If this solves your problem, consult with the printer of your letterhead to verify that the paper used meets the specifications for this product.
● Several optimize print modes can be used to address print quality issues. See
Print Quality menu on page 48 .
Repetitive defects ruler
If defects repeat at regular intervals on the page, use this ruler to identify the cause of the defect. Place the top of the ruler at the first defect. The marking that is beside the next occurrence of the defect indicates which component needs to be replaced.
258 Chapter 15 Solve problems ENWW
(0)
(36mm)
(40mm)
(50mm)
(71mm)
(82mm)
(94mm)
ENWW
(144mm)
(148mm)
36 mm
40 mm
50 mm
71 mm
82 mm
94 mm
144 mm
148 mm
Developer roller in an image drum.
The print quality defect will be in one of the four image drums (image drum).
Charge roller in an image drum.
The print quality defect will be spots or dots sometimes caused when feeding labels and will be in one of the four image drums (image drum).
Transfer 1 roller in the transfer unit (transfer kit).
Transfer 2 roller in the roller kit (transfer kit).
Tension in the transfer unit (transfer kit).
Image drum.
The print quality defect will be in one of the four image drums (image drum).
Pressure roller in the fuser (fuser kit).
Fusing roller in the fuser (fuser kit).
Correct print quality and copy quality problems 259
To identify if the image drum is the problem, insert an image drum from another HP Color LaserJet
CM6049f, if one is available, before ordering a new image drum.
If the defect repeats at 94.0 mm (3.75 inch) intervals, try replacing the image drum before replacing the fuser.
Print quality problems associated with the environment
If the product is operating in excessively humid or dry conditions, verify that the printing environment is
within specifications. See Environmental specifications on page 281 . Several optimization modes can
also help with environmental conditions. See
Use manual print modes on page 264 .
Print quality problems associated with jams
● Make sure that all paper is cleared from the paper path.
● If the product recently jammed, print two to three pages to clean the product.
● The paper does not pass through the fuser, causing image defects to appear on subsequent documents. Print two to three pages to clean the product.
Optimize and improve image quality
The following procedures can be used to solve most image quality problems.
Use supported paper
Using unsupported paper or other media in the product can cause a wide variety of image quality problems.
Calibrate the product
Calibration is a product function that optimizes print quality. If you experience any image-quality problems, calibrate the product.
At the control panel;
1.
Touch Administration .
2.
Scroll and touch Print Quality .
3.
Scroll and touch Calibration/Cleaning .
4.
Touch Quick Calibration or Full Calibration .
5.
Touch Calibrate .
Specify the correct paper type
When you send a print job to the product, specify the type of paper you are using.
1.
On the File menu in the software program, click Print .
2.
Select the product, and then click Properties or Preferences .
NOTE: The steps can vary; this procedure is most common.
260 Chapter 15 Solve problems ENWW
3.
Select the Paper/Quality tab.
4.
In the Paper Type drop-down box, select More...
and then select the paper type that best matches the paper that is loaded in the product.
Clean the fuser
Run the device cleaning page to keep the fuser free of toner and paper particles that can sometimes accumulate. Accumulation of toner and particles can cause specks to appear on the front or back side of your print jobs.
HP recommends that you use the cleaning page when there is a print quality issue.
A Cleaning message appears on the product control panel display while the cleaning is taking place.
In order for the cleaning page to work correctly, print the page on copier-grade paper (not bond, heavy, or rough paper).
Create and use the cleaning page
1.
Scroll to and touch Administration .
2.
Scroll to and touch Print Quality
3.
Touch Calibration/cleaning .
4.
Touch Process cleaning page .
Respond to control panel error messages
If you see a 54.Error <XX> message in the event log, you might need to perform some maintenance on the product in order to avoid more errors and solve print quality problems.
1.
Open and then close the right door of the product to log a 54.Error <XX> as the latest event in the event log.
2.
Scroll to and touch Administration .
3.
Scroll to and touch Troubleshooting .
4.
Scroll to and touch Event Log .
5.
Touch Print .
6.
Find the most recent event in the log.
● If the event is a 54.OE.01 Media Sensor event, you need to replace the registration second transfer assembly.
● If the event is a 54.OE.02 Media Sensor event, you need to replace the product transfer kit.
● If the event is a 54.OE.03 Media Sensor event, you need to clean the registration second transfer assembly and the media sensor using the following procedure.
ENWW Correct print quality and copy quality problems 261
Clean the registration second transfer assembly
1.
Open the right door.
2.
Locate and remove the cleaning brush.
3.
Lift the green handle on the transfer-access panel and open the panel.
1
2
262 Chapter 15 Solve problems ENWW
4.
Clean the media sensor with the cleaning brush.
5.
Close the transfer access panel, and replace the cleaning brush in its holder.
6.
Close the right door.
ENWW Correct print quality and copy quality problems 263
Use manual print modes
Try the following manual print modes to see if they solve the image quality problems. These options can be found in the Optimize sub-menu under the control panel Print Quality menu. See
Print Quality menu on page 48 .
● Fuser Temp : If you are seeing a faint image of the page repeated at the bottom of the page or on the following page, you should first make sure the Paper Type and Print Mode settings are correct for the type of paper you are using. If you continue to see ghost images on your print jobs, set the
Fuser Temp feature to one of the Alternate settings . Try the Alternate 1 setting first and see if it solves the problem. If you continue to see the problem, try Alternate 2 and then Alternate 3. With the Alternate 2 and Alternate 3 settings you may see an extra delay between jobs.
● Light Media : Set this feature to On if you are frequently seeing Fuser Delay Jam or Fuser Wrap
Jam messages, especially when printing on light-weight paper or on jobs with heavy toner coverage.
● Media Temp : Set this feature to Reduced if you are having problems with paper sticking together in the output bin.
● Environment : Enable this feature if the product is operating in a low temperature environment and you are having problems with print quality such as blisters in the printed image.
● Line Voltage : Enable this feature if the product is operating in a low voltage environment and you are having problems with print quality such as blisters in the printed image.
● Background : Turn this feature on if pages are printing with a shaded background. Using this feature can reduce gloss levels.
● Paper Curl : Set this feature to Reduced if excessive curling of paper in the output bin occurs. This setting will reduce printing speed and increase the frequency of consumable replacement.
● Pre-rotation : Turn this feature on if horizontal streaks appear on pages. Using this feature increases the warm-up time for the device.
● Tray 1 : If you are seeing marks on the back side of the paper or extra toner on pages when printing from Tray 1, set the mode to Alternate . When the mode is set to Alternate a cleaning cycle will be performed after each job that is printed from Tray 1. Using Alternate mode increase wear on all the print cartridges.
● Tracking Control : This setting should always be set to On .
● Cleaning Frequency = Normal/Alternate : Set this feature to Alternate if you are seeing defects in the printed output that repeat at 38 mm (1.5 inch) intervals. This feature increases the frequency at which the C roller is cleaned. Setting this feature to Alternate might also reduce printing speed and increase the frequency of consumable replacement.
● D-Blade Bias = Normal/Alternate : Set this feature to Alternate if you are seeing short, white, vertical lines in the printed output. The Alternate setting might also cause dark spots in the printed output, so be sure to test this setting on a few print jobs.
● Waste Bin = Normal/Alternate : Try setting this feature to Alternate if you are seeing lengthwise toner streaks in your printed output, especially in jobs with low toner coverage.
● Discharge Brush = Off/On : Enable this feature in low temperature and low humidity environments if you are seeing specks of toner scattered on double-sided jobs using lightweight paper and longer than ten pages.
264 Chapter 15 Solve problems ENWW
Print-quality-troubleshooting pages
Use the built-in print-quality-troubleshooting pages to help diagnose and solve print-quality problems.
1.
Scroll to and touch Administration
2.
Scroll to and touch Troubleshooting .
3.
Touch PQ Troubleshooting .
4.
Touch Print .
The product returns to the Ready state after printing the print-quality-troubleshooting pages. Follow the instructions on the pages that print out.
ENWW Correct print quality and copy quality problems 265
Performance problems
Problem
Pages print but are totally blank.
Pages print very slowly.
Pages did not print.
Cause Solution
The sealing tape might still be in the print cartridges.
Verify that the sealing tape has been completely removed from the print cartridges.
The document might contain blank pages.
Check the document that you are printing to see if content appears on all of the pages.
The product might be malfunctioning.
Heavier media types can slow the print job.
To check the product, print a
Configuration page.
Print on a different type of media.
Complex pages can print slowly.
Proper fusing may require a slower print speed to ensure the best print quality.
The RLT photo fix options under HP real life technologies on the Paper/
Quality tab of the print driver can cause slow printing.
De-select these options to improve print speed.
The product might not be pulling media correctly.
Make sure paper is loaded in the tray correctly.
The media is jamming in the device.
The USB cable might be defective or incorrectly connected.
Other devices are running on your computer.
If the problem persists, the pickup rollers and the separation pad might need to be replaced.
Clear the jam. See
● Disconnect the USB cable at both ends and reconnect it.
● Try printing a job that has printed in the past.
● Try using a different USB cable.
The product might not share a USB port.
If you have an external hard drive or network switchbox that is connected to the same port as the product, the other device might be interfering. To connect and use the product, you must disconnect the other device or you must use two USB ports on the computer.
266 Chapter 15 Solve problems ENWW
Solve fax problems
For help solving fax problems, go to www.hp.com/go/mfpfaxaccessory300 .
You can also refer to the Analog Fax Accessory 300 Fax Guide and the Analog Fax Accessory 300
Send Fax Driver Guide .
Solve e-mail problems
If you are unable to send e-mails by using the digital-send feature, you might need to reconfigure the
SMTP gateway address or the LDAP gateway address. Print a configuration page to find the current
SMTP and LDAP gateway addresses. See
Information pages on page 176 . Use the following
procedures to check if the SMTP and LDAP gateway addresses are valid.
Validate the SMTP gateway address
NOTE: This procedure is for Windows operating systems.
1.
Open an MS-DOS command prompt: click Start , click Run , and then type cmd .
2.
Type telnet followed by the SMTP gateway address and then the number 25, which is the port over which the product is communicating. For example, type telnet 123.123.123.123 25 where "123.123.123.123" represents the SMTP gateway address.
3.
Press Enter . If the SMTP gateway address is not valid, the response contains the message Could not open connection to the host on port 25: Connect Failed.
4.
If the SMTP gateway address is not valid, contact the network administrator.
Validate the LDAP gateway address
NOTE: This procedure is for Windows operating systems.
1.
Open Windows Explorer. In the address bar, type LDAP:// immediately followed by the LDAP gateway address. For example, type LDAP://12.12.12.12
where "12.12.12.12" represents the
LDAP gateway address.
2.
Press Enter . If the LDAP gateway address is valid, the Find People dialog box opens.
3.
If the LDAP gateway address is not valid, contact the network administrator.
ENWW Solve fax problems 267
Solve network connectivity problems
If the product is having problems communicating with the network, use the information in this section to resolve the problem.
Solve network printing problems
● Make sure that the network cable is securely seated into the product's RJ45 connector.
● Make sure that the Link LED on the formatter is lit. See
Understand lights on the formatter on page 257 .
● Make sure that the I/O card is ready. Print a configuration page (see
a second page that shows the network settings and status.
NOTE: The HP Jetdirect print server supports various network protocols (TCP/IP, IPX/SPX,
Novell NetWare, AppleTalk, and DCL/LLC). Make sure that the correct protocols and network parameters are set correctly.
On the HP Jetdirect configuration page, verify the following items for your protocol:
◦ Under HP Jetdirect Configuration, the status is "I/O Card Ready."
◦ Protocol status is "Ready."
◦ An IP address is listed.
◦ The configuration method (Config by:) is listed correctly. See the network administrator if you are not sure which method is correct.
● Try printing the job from another computer.
● To verify that a product works with a computer, use a USB cable to connect it directly to a computer.
You will have to reinstall the printing software. Print a document from a program that has printed correctly in the past. If this works, a problem with the network might exist.
● Contact your network administrator for assistance.
Verify communication over the network
If the HP Jetdirect configuration page shows an IP address for the product, use this procedure to verify that you can communicate with the product over the network.
1.
Windows : Click Start , click Run , and then type cmd . An MS-DOS command prompt opens.
-or-
Mac: Click Applications , click Utilities , and then open the Terminal application. The terminal window opens.
2.
Type ping followed by the IP address. For example, type ping XXX.XXX.XXX.XXX
where
"XXX.XXX.XXX.XXX" is the IPv4 address that is shown on the HP Jetdirect configuration page. If the product is communicating over the network, the response is a list of replies from the product.
3.
Verify that the IP address is not a duplicate address on the network by using the address resolution protocol (arp -a) command. At the prompt, type arp -a . Find the IP address in the list and compare its physical address to the hardware address that is listed on the HP Jetdirect configuration page
268 Chapter 15 Solve problems ENWW
in the section called HP Jetdirect Configuration. If the addresses match, all network communications are valid.
4.
If you cannot verify that the product is communicating over the network, contact the network administrator.
ENWW Solve network connectivity problems 269
Solve common Macintosh problems
This section lists problems that can occur when using Mac OS X.
Table 15-1 Problems with Mac OS X
The printer driver is not listed in the Print Center or Printer Setup Utility.
Cause Solution
The product software might not have been installed or was installed incorrectly.
Make sure that the product PPD is in the following hard-drive folder:
Library/Printers/PPDs/Contents/Resources/
<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. If necessary, reinstall the software.
See the getting started guide for instructions.
The Postscript Printer Description (PPD) file is corrupt.
Delete the PPD file from the following hard-drive folder: Library/
Printers/PPDs/Contents/Resources/<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. Reinstall the software. See the getting started guide for instructions.
The product name, IP address, or Rendezvous/Bonjour host name does not appear in the product list in the Print Center or Printer
Setup Utility.
Cause Solution
The product might not be ready.
The wrong connection type might be selected.
The wrong product name, IP address, or Rendezvous/Bonjour host name is being used.
The interface cable might be defective or of poor quality.
Make sure that the cables are connected correctly, the product is on, and the ready light is on. If you are connecting through a USB or
Ethernet hub, try connecting directly to the computer or use a different port.
Make sure that USB, IP Printing, or Rendezvous/Bonjour is selected, depending on the type of connection that exists between the product and the computer.
Print a configuration page in order to check the product name, IP address, or Rendezvous host name. Verify that the name, IP address, or Rendezvous host name on the configuration page matches the product name, IP address, or Rendezvous host name in the Print
Center or Printer Setup Utility.
Replace the interface cable. Make sure to use a high-quality cable.
The printer driver does not automatically set up your selected product in the Print Center or Printer Setup Utility.
Cause Solution
The product might not be ready.
The product software might not have been installed or was installed incorrectly.
Make sure that the cables are connected correctly, the product is on, and the ready light is on. If you are connecting through a USB or
Ethernet hub, try connecting directly to the computer or use a different port.
Make sure that the product PPD is in the following hard-drive folder:
Library/Printers/PPDs/Contents/Resources/
<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. If necessary, reinstall the software.
See the getting started guide for instructions.
270 Chapter 15 Solve problems ENWW
Table 15-1 Problems with Mac OS X (continued)
The printer driver does not automatically set up your selected product in the Print Center or Printer Setup Utility.
Cause
The Postscript Printer Description (PPD) file is corrupt.
The interface cable might be defective or of poor quality.
Solution
Delete the PPD file from the following hard-drive folder: Library/
Printers/PPDs/Contents/Resources/<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. Reinstall the software. See the getting started guide for instructions.
Replace the interface cable. Make sure to use a high-quality cable.
A print job was not sent to the product that you wanted.
Cause
The print queue might be stopped.
The wrong product name or IP address is being used. Another product with the same or similar name, IP address, or Rendezvous host name might have received your print job.
Solution
Restart the print queue. Open print monitor and select Start Jobs .
Print a configuration page in order to check the product name, IP address, or Rendezvous host name. Verify that the name, IP address, or Rendezvous host name on the configuration page matches the product name, IP address, or Rendezvous host name in the Print
Center or Printer Setup Utility.
An encapsulated PostScript (EPS) file does not print with the correct fonts.
Cause
This problem occurs with some programs.
Solution
● Try downloading the fonts that are contained in the EPS file to the product before printing.
● Send the file in ASCII format instead of binary encoding.
You are unable to print from a third-party USB card.
Cause
This error occurs when the software for USB products is not installed.
Solution
When adding a third-party USB card, you might need the Apple USB
Adapter Card Support software. The most current version of this software is available from the Apple Web site.
ENWW Solve common Macintosh problems 271
Table 15-1 Problems with Mac OS X (continued)
When connected with a USB cable, the product does not appear in the Print Center or Printer Setup Utility after the driver is selected.
Cause
This problem is caused by either a software or a hardware component.
Solution
Software troubleshooting
● Check that your Macintosh supports USB.
● Verify that your Macintosh operating system is Mac OS X v10.3
or later.
● Ensure that your Macintosh has the appropriate USB software from Apple.
Hardware troubleshooting
● Check that the product is turned on.
● Verify that the USB cable is connected correctly.
● Check that you are using the appropriate high-speed USB cable.
● Ensure that you do not have too many USB devices drawing power from the chain. Disconnect all of the devices from the chain, and connect the cable directly to the USB port on the host computer.
● Check to see if more than two nonpowered USB hubs are connected in a row on the chain. Disconnect all of the devices from the chain and connect the cable directly to the USB port on the host computer.
NOTE: The iMac keyboard is a nonpowered USB hub.
272 Chapter 15 Solve problems ENWW
A Supplies and accessories
●
Order parts, accessories, and supplies
●
ENWW 273
Order parts, accessories, and supplies
To order parts, accessories, and supplies, contact your dealer.
274 Appendix A Supplies and accessories ENWW
Part numbers
Ordering information and availability might change during the life of the product.
Accessories
Item Description
HP 3-bin Stapler/Stacker Accessory 3-bin stapler/stacker with output accessory bridge unit
HP 3-bin Stapler/Stacker or HP Booklet
Maker/Finisher staple cartridge (upper cartridge on HP Booklet Maker/Finisher)
5000-staple replacement cartridge
HP Booklet Maker/Finisher Accessory Booklet maker finisher with output accessory bridge unit
HP Booklet Maker/Finisher saddle-stitch staple cartridge (lower cartridge)
2000-staple replacement cartridge
(quantity of 2)
HP LaserJet analog fax accessory 300 Provides fax capability for the product.
Part number
CC517A
C8091A
CC516A
CC383A
Q3701A
Print cartridges
Item Description
HP Color LaserJet black print cartridge 19,500-page black cartridge
HP Color LaserJet cyan print cartridge 21,000-page cyan cartridge
HP Color LaserJet yellow print cartridge 21,000-page yellow cartridge
HP Color LaserJet magenta print cartridge
21,000-page magenta cartridge
Part number
CE830C
CE301C
CE302C
CE303C
Image drums
Item Description
HP Color LaserJet black image drum
HP Color LaserJet cyan image drum
35,000-page black image drum
35,000-page cyan image drum
HP Color LaserJet yellow image drum 35,000-page yellow image drum
HP Color LaserJet magenta image drum 35,000-page magenta image drum
Part number
CE304C
CE305C
CE306C
CE307C
Maintenance kits
Item
Image fuser kit
Image fuser kit
Description
110 volt
220 volt
Part number
CB457A
CB458A
ENWW Part numbers 275
Item
Roller kit
Transfer kit
ADF roller kit
Description
Memory
Item Description
200-pin DDR memory DIMM (dual inline memory module)
128 MB
256 MB
Boosts the ability of the product to handle large or complex print jobs.
Cables and interfaces
Item
Enhanced I/O (EIO) card
USB cable
Part number
CB459A
CB463A
CE487A
Part number
Q7557A
Q7558A
Description
HP Jetdirect 635n IPv6/IPsec Print
Server
2-meter standard USB-compatible device connector
Part number
J7961G
C6518A
276 Appendix A Supplies and accessories ENWW
B Product specifications
●
●
●
●
ENWW 277
Physical specifications
Table B-1 Product dimensions
Product Height
1
HP Color LaserJet CM6049f MFP
Without print cartridge
1194 mm (47 in)
Depth
635 mm (25 in)
Width
704 mm (27.7 in)
Weight
145 kg (319 lb)
Table B-2 Product dimensions, with all doors and trays fully opened
Product Height Depth
HP Color LaserJet CM6049f MFP 1524 mm (60 in) 1079.5 mm (42.5 in)
Width
983 mm (38.7 in)
278 Appendix B Product specifications ENWW
Electrical specifications
WARNING!
Power requirements are based on the country/region where the product is sold. Do not convert operating voltages. This can damage the product and void the product warranty.
Table B-3 Power requirements (HP Color LaserJet CM6049f MFP)
Specification 110-volt models 220-volt models
Power requirements
Rated current
100 to 127 volts (± 10%)
50/60 Hz (± 2 Hz)
10.5 A
220 to 240 volts (± 10%)
50/60 Hz (± 2 Hz)
5.5 A
Table B-4 Power consumption HP Color LaserJet CM6049f MFP (average, in watts)
Product model Printing Ready Sleep Off
HP Color LaserJet
CM6049f MFP
1265 W 251.7 W 26.5 W 0.72 W
Values subject to change. See www.hp.com/support/cljcm6049mfp for current information.
Printing and copying speeds are 40 ppm for Letter and A4 sizes.
Default time from Ready mode to Sleep mode = 60 minutes.
Recovery time from Sleep mode = less than 20 seconds
ENWW Electrical specifications 279
Acoustic specifications
Table B-5 Sound power and pressure level
(HP Color LaserJet CM6049f MFP)
Sound power level Declared per ISO 9296
Ready
L
WAd
= 7.1 Bels (A) [71 dB(A)]
L
WAd
= 7.1 Bels (A) [71 dB(A)]
L
WAd
= 4.7 Bels (A) [47 dB(A)]
Sound pressure level
Declared per ISO 9296
L pAm
=50 dB (A)
L pAm
=52 dB (A)
1
2
Ready L pAm
=37 dB (A)
Values subject to change. See www.hp.com/support/cljcm6049mfp for current information.
Configuration tested: Base model, simplex copying from ADF with A4 paper size.
280 Appendix B Product specifications ENWW
Environmental specifications
Environmental condition
Temperature (product and print cartridge)
Relative humidity
Recommended
17° to 25°C (62.6° to 77°F)
Allowed
10° to 30°C (50° to 86°F)
30% to 70% relative humidity
(RH)
10% to 80% RH
Storage/standby
0° to 35°C (32° to 95°F)
5% to 95%
ENWW Environmental specifications 281
282 Appendix B Product specifications ENWW
C Regulatory information
ENWW 283
Compliance with FCC regulations
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
284 Appendix C Regulatory information ENWW
Declaration of Conformity
Declaration of Conformity according to ISO/IEC 17050–1 and EN 17050–1
Manufacturer's Name:
Manufacturer's Address:
Hewlett-Packard Company
DoC#: BOISB-0601–02–rel.6.0
11311 Chinden Boulevard,
Boise, Idaho 83714-1021, USA declares that the product
Product Name:
Accessories: 3)
Regulatory Model Number:
Product Options:
2)
HP Color LaserJet CM6030/CM6040/CM4349 MFP series
CB473A – 1x500-sheet input tray/stand
CB474A – 3x500-sheet input tray/stand
Q6999A/CC516A – Booklet Maker
Q6998A/CC517A – 3-Bin Stapler/Stacker
BOISB-0308-00 – Fax Module
BOISB-0601-02
ALL
Toner Cartridges/Drums: CB390A, CB381A, CB382A, CB383A, CB384A, CB385A, CB386A,
CB387A, CE830C, CE301C, CE302C, CE303C, CE304C, CE305C, CE306C, CE307C conforms to the following Product Specifications:
Safety: IEC 60950-1:2001 / EN60950-1: 2001 + A11
IEC 60825-1:1993 +A1 +A2 / EN 60825-1:1994 +A1 +A2 (Class 1 Laser/LED Product)
GB4943-2001
EMC: CISPR 22:2005 / EN 55022:2006 – Class A 1)
EN 61000-3-2:2006
EN 61000-3-3:1995 + A1
EN 55024:1998+A1 + A2
FCC Title 47 CFR, Part 15 Class A / ICES-003, Issue 4
GB9254-1998, GB17625.1–2003
Telecom TBR-21:1998; FCC Title 47 CFR, Part 68 4)
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 2004/108/EC and the Low Voltage Directive 2006/95/EC, and the
R&TTE Directive 1999/5/EC (Annex II), and carries the CE-Marking accordingly.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
2) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name or the product number(s).
3) All worldwide modular approvals for analog fax accessory obtained by Hewlett-Packard under the regulatory model number BOISB-0308-00 incorporate the Multi-Tech Systems MT5634SMI Socket Modem Module.
4) Telecom approvals and standards appropriate for the target countries/regions have been applied to this product, in addition to those listed above.
Boise, Idaho , USA
March 2009
For regulatory topics only:
European Contact: Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe, Herrenberger Straße 140, D-71034 Böblingen, Germany, (FAX: +49-7031-14-3143) www.hp.com/go/ certificates
USA Contact: Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160, Boise, Idaho 83707-0015, USA,
(Phone: 208-396-6000)
ENWW Declaration of Conformity 285
Environmental product stewardship program
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally sound manner. This product has been designed with several attributes to minimize impacts on our environment.
Ozone production
This product generates no appreciable ozone gas (O
3
).
Power consumption
Power usage drops significantly while in Ready and Sleep mode, which saves natural resources and saves money without affecting the high performance of this product. To determine the ENERGY STAR® qualification status for this product, see the Product Data Sheet or Specifications Sheet. Qualified products are also listed at: www.hp.com/go/energystar
Toner consumption
EconoMode uses less toner, which might extend the life of the print cartridge.
Paper use
This product’s optional automatic duplex feature (two-sided printing) and N-up printing (multiple pages printed on one page) capability can reduce paper usage and the resulting demands on natural resources.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of the product’s life.
HP LaserJet print supplies
It’s easy to return and recycle your empty HP LaserJet print cartridges—free of charge—with HP Planet
Partners. Multilingual program information and instructions are included in every new HP LaserJet print cartridge and supplies package. You help reduce the toll on the environment further when you return multiple cartridges together rather than separately.
HP is committed to providing inventive, high-quality products and services that are environmentally sound, from product design and manufacturing to distribution, customer use, and recycling. When you participate in the HP Planet Partners program, we ensure your HP LaserJet print cartridges are recycled properly, processing them to recover plastics and metals for new products and diverting millions of tons of waste from landfills. Please note that the cartridge will not be returned to you. Thank you for being environmentally responsible!
NOTE: Use the return label to return original HP LaserJet print cartridges only. Please do not use this label for HP inkjet cartridges, non-HP cartridges, refilled or remanufactured cartridges, or warranty returns. For information about recycling your HP inkjet cartridges, please go to www.hp.com/recycle .
286 Appendix C Regulatory information ENWW
Return and recycling instructions
United States and Puerto Rico
The enclosed label in the HP LaserJet toner cartridge box is for the return and recycling of one or more
HP LaserJet print cartridges after use. Please follow the applicable instructions below.
Multiple returns (more than one cartridge)
1.
Package each HP LaserJet print cartridge in its original box and bag.
2.
Tape the boxes together using strapping or packaging tape. The package can weigh up to 31 kg
(70 lb).
3.
Use a single pre-paid shipping label.
OR
1.
Use your own suitable box, or request a free bulk collection box from www.hp.com/recycle or
1-800-340-2445 (holds up to 31 kg (70 lb) of HP LaserJet print cartridges).
2.
Use a single pre-paid shipping label.
Single returns
1.
Package the HP LaserJet print cartridge in its original bag and box.
2.
Place the shipping label on the front of the box.
Shipping
For all HP LaserJet print cartridge recycling returns, give the package to UPS during your next delivery or pickup, or take it to an authorized UPS drop-off center. For the location of your local UPS drop-off center, call 1-800-PICKUPS or visit www.ups.com
. If you are returning via USPS label, give the package to a U.S. Postal Service carrier or drop off at a U.S. Postal Service Office. For more information, or to order additional labels or boxes for bulk returns, visit www.hp.com/recycle or call 1-800-340-2445.
Requested UPS pickup will be charged normal pickup rates. Information subject to change without notice.
Non-U.S. returns
To participate in HP Planet Partners return and recycling program, just follow the simple directions in the recycling guide (found inside the packaging of your new product supply item) or visit www.hp.com/ recycle . Select your country/region for information on how to return your HP LaserJet printing supplies.
Paper
This product is capable of using recycled papers when the paper meets the guidelines outlined in the
HP LaserJet Printer Family Print Media Guide . This product is suitable for the use of recycled paper according to EN12281:2002.
Material restrictions
This HP product contains a battery that may require special handling at end-of-life.
The battery contained in this product includes:
ENWW Environmental product stewardship program 287
Type
Weight
Location
User removable
Carbon monofluoride lithium battery
0.8 grams
Formatter board
No
This product contains mercury in the fluorescent lamp of the control panel liquid crystal display that might require special handling at end-of-life.
For recycling information you can visit www.hp.com/go/recycle or contact your local authorities or the
Electronics Industry Alliance ( www.eiae.org
).
Disposal of waste equipment by users in private households in the
European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Material Safety Data Sheet (MSDS)
Material Safety Data Sheets (MSDS) for supplies containing chemical substances (for example, toner) can be obtained by accessing the HP Web site at www.hp.com/go/msds or www.hp.com/hpinfo/ community/environment/productinfo/safety .
288 Appendix C Regulatory information ENWW
For more information
To obtain information about these environmental topics:
● Product environmental profile sheet for this and many related HP products
● HP’s commitment to the environment
● HP’s environmental management system
● HP’s end-of-life product return and recycling program
● Material Safety Data Sheets
Visit www.hp.com/go/environment or www.hp.com/hpinfo/globalcitizenship/environment .
ENWW Environmental product stewardship program 289
Certificate of volatility
This is a statement regarding the volatility of customer data stored in memory. It also outlines how to erase secure data from the device.
Types of memory
Volatile memory
The MFP utilizes volatile memory (64MB on the board and 256MB installed, for a total of 320MB) to store customer data during the printing and copying process. When the MFP is powered off, this volatile memory is erased.
Non-volatile memory
The MFP utilizes non-volatile memory (EEPROM) to store system control data and user preference settings. No customer print or copy data is stored in non-volatile memory. This non-volatile memory can be cleared and restored to factory defaults by performing a Cold Reset or Restore Factory Defaults from the control panel.
Hard-disk-drive memory
The MFP contains an internal hard disk drive (40GB or larger) that may retain data after the MFP is powered off. The MFP also may contain additional optional compact flash storage, or an external EIO hard disk. Data stored in these devices may be from incoming/outgoing fax or email files, stored copy or print jobs, fax or email address books, or third-party solutions. Some of this data can be erased from the control panel of the MFP, but most must be erased using the Secure Storage Erase features available within HP Web Jetadmin. Secure Storage Erase features comply with U.S. Department of
Defense (DOD) specification 5220–22.M.
290 Appendix C Regulatory information ENWW
Safety statements
Laser safety
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has implemented regulations for laser products manufactured since August 1, 1976. Compliance is mandatory for products marketed in the United States. The device is certified as a “Class 1” laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. Since radiation emitted inside the device is completely confined within protective housings and external covers, the laser beam cannot escape during any phase of normal user operation.
WARNING!
Using controls, making adjustments, or performing procedures other than those specified in this user guide may result in exposure to hazardous radiation.
Canadian DOC regulations
Complies with Canadian EMC Class A requirements.
« Conforme à la classe A des normes canadiennes de compatibilité électromagnétiques. « CEM ». »
VCCI statement (Japan)
Power cord statement (Japan)
EMC statement (Korea)
EMI statement (Taiwan)
ENWW Safety statements 291
General telecom statement
The HP Color LaserJet CM6049f MFP has the HP LaserJet Analog Fax Accessory 300 already installed to provide communication to the public switch telephone network (PSTN) for fax functionality. See the
HP LaserJet Analog Fax Accessory 300 User Guide for all regulatory approval information and regulatory notices associated with the fax functionality and that device.
Laser statement for Finland
Luokan 1 laserlaite
Klass 1 Laser Apparat
HP LaserJet CM6049f, laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING !
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet CM6049f - kirjoittimen sisällä ei ole käyttäjän huollettavissa olevia kohteita. Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai muita käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka voidaan suorittaa ilman erikoistyökaluja.
VARO !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömällelasersäteilylle laitteen ollessa toiminnassa. Älä katso säteeseen.
VARNING !
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig laserstrålning. Betrakta ej strålen. Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 775-795 nm Teho 5 m W Luokan 3B laser.
292 Appendix C Regulatory information ENWW
Substances Table (China)
ENWW Safety statements 293
294 Appendix C Regulatory information ENWW
Index
Symbols/Numerics
3-bin mailbox
3-bin stapler/stacker
500-sheet trays
A accessories
3-bin stapler/stacker 114 booklet-maker finisher 114 optional output 114
address books, e-mail
recipient lists 166 recipient lists, creating 166
address, printer
Macintosh,
ADF
ADF output bin
Administration menu, control
advanced printing options
alternative letterhead mode 142
Attention light
automatic two-sided printing path
B
bins
blank pages, troubleshooting 266
blocked fax list, printing 177
booklet maker
books
both sides, printing on
browser requirements
buttons, control panel
C cabinet/stand
cable, USB
cables
cancel
print 138 cancel a print request 138
capacity
ADF 4 output bins 4 stapler/stacker 4
cartridges
cartridges, print
clean
ENWW Index 295
outside of product 206 touchscreen 206
clock
color
colored text
configuration page
configure
connectivity
control panel
copies, number of
copy
control-panel navigation 152 copy screen 152 from document feeder 152 from glass 152
Job Mode 159 multiple originals 159
copying
custom-size paper settings
D
Data light
default settings
density
device status
diagnostics
digital sending
embedded Web server
validating gateway
Digital Sending tab, embedded
DIMMs (dual inline memory modules)
document feeder copying two-sided
document feeder kit,
double-sided printing
Macintosh settings 74 dpi, settings 74
296 Index ENWW
drivers
Macintosh,
duplex
duplex printing
duplex printing accessory
duplexer
E
economy settings
EIO cards
embedded Web server
Enhanced I/O card
envelope feeder
envelopes
environment, specifications 281
Environmental Product
EPS files, troubleshooting 271
Error button, control panel
error messages
European Union, waste
EWS
Explorer, versions supported
embedded Web server
validating gateway
F fax accessory
analog fax 172 configure features 172 connecting phone line 172
Fax Activity Log
faxing
Finnish laser safety
first page
folders
fonts
EPS files, troubleshooting 271
fuser
G gateways
glass
graphical display, control
H hard disk
Help button, control panel
touchscreen 14 help, control panel 14
Home button, control panel
HP Jetdirect print server
HP Jetdirect print servers
ENWW Index 297
HP Printer Utility, Macintosh 73
HP Web Jetadmin
I
I/O configuration
image drums
image fuser kit, 110 volt
image fuser kit, 220 volt
Information tab, embedded Web
installing
interface ports
Internet Explorer, versions supported
IP address
Macintosh,
J
jams
Jetadmin
Jetdirect print server
job storage
jobs
K keys, control panel
L
landscape orientation
laser safety statements 291, 292
LDAP servers
embedded Web server
validating gateway
letterhead
lights
load media
loading documents, sizes
supported 165 scanner glass 165 sizes supported 165
locking
M
Macintosh
problems,
supported operating
USB card,
Macintosh driver settings
mailbox, 3-bin
manage
Material Safety Data Sheet
298 Index ENWW
media custom-size, Macintosh
memory
menu map
menus, control panel
messages
multiple pages per sheet
N n-up printing
Netscape Navigator, versions supported
network
Networking tab, embedded Web
networks
configuring gateway
protocol configuration page,
Transmission Control Protocol
validating gateway
O
operating environment
operating systems supported 62,
optional output accessories 114
ordering
orientation
outdoor signs
output bins
output quality
P
pages
blank 266 not printing 266 printing slowly 266
pages per sheet
paper covers, using different
paper 139 custom size, selecting 139
custom-size, Macintosh
first and last pages, using
type 98, 113 type and size 113
paper jams
parallel port
part numbers
accessories 275 image drums 275
ENWW Index 299
parts
PCL drivers
phone line, connecting fax
photos
portrait orientation
ports
troubleshooting
PostScript Printer Description
(PPD) files
power
PPDs
pre-printed paper
pre-punched paper
print cartridge
print cartridges
print drivers
print features
print media
print on both sides
print paper
print quality
print server card
printing
printing from tray 2, 3, or 4 102
private jobs
problem-solving
Error button, control panel
proof and hold
protocol configuration page,
Q quality
R
Ready light
recycling
HP printing supplies returns and
regulatory statements
environmental product
remote firmware update
removing Macintosh software 72
repeating defects,
replace
resize documents
resolution
Resolution Enhancement
REt (Resolution Enhancement
retention, job
rollers
300 Index ENWW
S
scale documents
scanner glass
scanning
scanning to e-mail
embedded Web server
security
locking control panel
sending to e-mail
embedded Web server
validating gateway
separator page
serial number
Service menu, control panel 59
Services tab
settings
Settings tab, embedded Web
Sleep mode
sleep settings
SMTP servers configuring gateway
validating gateway
software
supported operating
systems 62, 72 uninstalling Macintosh 72
special media
special paper
specifications
standard output bin
staple cartridges empty, stop or continue
staple options
stapler empty, stop or continue
stapler options
stapler/stacker
staples
Start button, control panel
status
Home screen, control
HP Printer Utility,
Stop button, control panel
storage cabinet
ENWW Index 301
storage, job
store jobs
storing
supplies
status, viewing with embedded
status, viewing with HP Printer
supply-status, Services tab
support
supported utilities
system requirements
T
TCP/IP
tests
Time/Scheduling menu, control
toner
top cover
Transmission Control Protocol
tray 1
tray 2, 3, 4, 5
trays
automatic media sensing 111 configure 111
troubleshooting
pages not printing 266 pages printing slowly 266
quality 258 repeating defects 258
two-sided printing
typefaces
U uninstalling Macintosh
USB port
troubleshooting
V validating gateway
W
Warning button, control panel
watermarks
weatherproof maps
Web browser requirements
Web Jetadmin
Web sites
HP Web Jetadmin,
Material Safety Data Sheet
Windows
supported operating
302 Index ENWW
© 2009 Hewlett-Packard Development Company, L.P.
www.hp.com
*CE799-90904*
*CE799-90904*
CE799-90904
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement