Savant HST-SAVANT6PLUS-00 SAVANT SMART HOST SERVICE PLUS - WITH SEPARATE IP AUDIO MUSIC SERVER AND STANDA Quick Reference Guide

Savant® Smart Host Rack Mountable

Quick Reference Guide

Box Contents

(1) Savant® Smart Host Rack Mountable - (SHR-2000-00)

(1) Install Kit (075-0223-xx)

(2) 6-pin Screw Down Plug-in Connector Black (028-9352-xx)

(2) 3-pin Screw Down Plug-in Connector Black (028-9351-xx)

(1) Product and Regulatory Insert (009-1950-xx)

Specifications

Environmental

Temperature

Humidity

Cooling

Maximum BTU

32° to 104° F (0° to 40° C)

10% to 90% Relative Humidity (non-condensing)

10 CFM

34.1 BTU/hr

Dimensions and Weights

Height

Width

Depth

Weight

1.6 in (4.15 cm)

8.5 in (21.50 cm)

3.7 in (9.33 cm)

Net: 1.4 lb (0.64 kg)

Shipping 2.3 lb (1.05 kg)

1U Rack Space

Power

Input Power 5V DC 3A

Maximum Power 15 watt s

Power over

Ethernet (PoE)

Regulatory

IEEE 802.3af

FCC Part 15 CE

Safety and

Emissions

C-Tick

RoHS Compliant

Minimum Supported Release

Savant Software da Vinci 9.2

Front Panel

Power Status

A Power LED

B Status LED

C

A B

Mounting

Points

C

Green : System has power and is operating normally.

Off : System is not receiving power.

Off : Disconnected from power supply.

Amber : Host is booting/rebooting and is disconnected from the network.

Green : Connected to the local network and is assigned an IP Address.

Threaded insert for use with optional rack mounts

Chassis Installation

The Smart Host can be installed on a solid, flat, level surface such as a table, cabinet, or shelf. The location should be dry, well ventilated, and out of direct sunlight.

Rack

The optional RMB-PAVAM2F-xx or RMB-PAVAM2-xx allows two devices to be mounted side by side. For example a Smart Host can be mounted next to a PAV-AIM7C. This rack is compatible with all standard 19-inch National Electrical Manufacturers Association (NEMA) rack mounts.

The instructions below show the RMB-PAVAM2F-xx, both brackets install the same way they just face different directions.

1. Align the bracket with the Smart Host mounting points.

2. Attach using the screws provided with the bracket.

Network Configuration

For information on network requirements, refer to the Savant Device

Networking Guidelines on the Savant Community .

Refreshing the IP Connection

After connecting to a new network, changing routers, or if the IP

Address range in the router was changed, the IP connection should be refreshed. To refresh the IP connection, do one of the following:

– Hot Plug the Ethernet (LAN) Connection

– Cycle power

SHR-2000-00 | 009-1909-02 | 200505

Copyright 2021 Savant Systems, Inc.

1 of 2

45 Perseverance Way, Hyannis, MA 02601

Savant.com

| 508.683.2500

Rear Panel

A B

Reset

Ethernet USB

C

Audio

RS232-1

D

RS232-2

E

IR

- 2 + - 3 +

F

5VDC

Control Connections

RS-232 Wiring

Pin 1: No Connection Pin 5: RXD (Receive)

Pin 2: No Connection Pin 6: TXD (Transmit)

Pin 3: No Connection Pin 7: CTS (Flow Control)

Pin 4: GND (Ground) Pin 8: RTS (Flow Control)

Pin 1 Pin 8

5 + G 1 PD

GPIO

A Reset

B USB

C Audio

D RS-232

E IR

G

F Relay

G Ethernet

H GPIO

I 5V DC

H I

Resets the network settings of the device.

Hold Reset Button for 5 seconds while powered on to clear network settings. Status LED will rapidly blink red when reset is complete.

Not Used

96k / 24 bit fixed volume TOSLink (Optical) digital audio output. Connect to digital optical audio input on switcher for using the Audio

Interrupt Service (AIS).

8-pin RJ-45 female.

Used to transmit and receive serial binary data to and from serial controllable devices.

Ports 1-2 RS-232 - CTS/RTS handshaking. CTS

RTS handshaking availability is based on the component profile.

See RS-232 Wiring

section for pin-outs.

6-pin Screw Down Plug-in Connector. Used to send IR signals to control devices with an IR input or IR receiver via an IR flasher (5V tolerant only).

See IR Wiring

section for important precautions regarding IR functionality before making connections.

3-pin Screw Down Plug-in Connector. See Relay

Wiring section for pin-outs.

Normally Open (NO) / Normally Closed (NC) to control devices requiring basic on/off operation.

DC Voltage Max: 30V DC 1A

8-pin RJ-45 female.

10/100/1000 Base-T auto negotiating port.

Connecting to this port will disable Wi-Fi settings.

3-pin Screw Down Plug-in Connector. See GPIO

Wiring section for pin-outs.

GPIO Input - When configured as an input, the processor will look for a low (<0.8V DC) or a high

(>2.4V DC) state. Minimum 0V DC / Maximum

12V DC.

GPIO Output - When configured as an output, the port provides a binary output of 0-12V DC

150mA max.

5V DC 3A - Connect included wall wart power supply between the 5V DC connection and a 115-

240V AC surge protected outlet.

Further Product Information

To view available documentation, detailed product specs, and more:

– Visit the Savant Knowledge tab via the Savant Customer

Community to search all Savant documentation.

RJ-45 Connector

(Gold pins facing up)

IMPORTANT NOTES!

– Wire colors are included to identify the pins used for this connection. Colors shown do not represent any wiring standard.

– When wiring, DO NOT connect any wires within the cable that are not required for communications.

– Pins 7 & 8 are only required for CTS/RTS handshaking.

– CTS/RTS handshaking is supported for flow control based on the profile used in the Blueprint configuration.

– RS-422/485 is not supported

– Refer to the RS-232 Conversion to DB9 and RS-422/485 Pin-out

Application Note on the Savant Customer Community for more information on RJ-45 to DB9 adapters offered by Savant.

Relay Wiring

Both Normally Open and Normally Closed outputs are available.

Pin 1: NC

(Normally Closed)

Pin 2: Common

Pin 3: NO

(Normally Open)

NC / / NO

1 2 3

GPIO - General Purpose Input/Output

– GPIO’s configured as an output can be used to trigger an action within the system such as switching a device.

– GPIO configured as an input can detect a state change and trigger a workflow.

Pin 1: GND (Ground)

Pin 2: GPIO 1

Pin 3: PD (Pulldown)

1 2 3

Gnd I/O PD

GPIO 1

Standard

GPIO Using

PD Jumper

– GPIO pins configured as an input are pulled high to (+12V) during the boot process. To force the GPIO signal low during a boot-up.

Connect the PD pin to the GPIO pin. This forces the GPIO output to

(< 0.8V) during the processor boot times.

IR Wiring (Infrared)

– Ensure that all IR emitters are within 15 feet (4.6 meters) from the controllers location.

– Use of 3rd party flashing IR emitters with Talk Back is not recommended. These types of emitters can draw voltage away from the IR signal that can degrade IR performance.

Pin 1: IR 1 -

Pin 2: IR 1 +

Pin 3: IR 2 -

Pin 4: IR 2 +

Pin 5: IR 3 -

Pin 6: IR 3 +

-

IR1

+

1 2

-

IR2

+

3

-

IR3

+

4 5 6

Use White Stripe for Positive (+)

– IR connections IR4 to IR6 (not shown in diagram) follow the same wiring as connections IR1 to IR3.

SHR-2000-00 | 009-1909-02 | 200505

Copyright 2021 Savant Systems, Inc.

2 of 2

45 Perseverance Way, Hyannis, MA 02601

Savant.com

| 508.683.2500