PRODUCT SHEET
GB
A. Refrigerator Compartment
2.
Electronic control panel / light unit
3.
Shelves / Shelf area
4.
Multi-flow cold air system
5.
Cooler compartment
6.
Rating plate with commercial name
7a.
Crisper divider
8.
Egg tray
9.
Reversibility kit
10.
Separator
11.
Door trays
B. Freezer Compartment
12.
Area for freezing (with/without flap)
13.
Area for storing frozen foods
14.
Ice tray
15.
Plastic shelf
16.
The freezer door trays for pizza or other frozen products with a short storage time (2** storage compartment)
Depending on the model the number and type of accessories may vary.
Anti-bacterial protection:
1.
Filter in fan (depending on the model)
7.
Crisper with antibacterial additives (depending on the model)
17.
Door seals
The crisper and the door seals are manufactured from materials that inhibit bacterial growth.
Notes:
- In case it'll have a flap, please remember that to maximize the storage volume it's suggested to remove it.
- All shelves and door trays are removable. Freezer plastic shelf cannot be removed to have a good air flow rate inside freezer compartment.
- The internal temperatures of the appliance depend on the ambient temperature, frequency of opening the doors, as well as location of the appliance. Temperature setting must consider these factors.
- The appliance accessories are not suitable for washing in dishwasher.
HOW TO START THE APPLIANCE
Fit the spacers (if supplied) on the upper part of the condenser at the rear of the appliance.
After plugging the appliance to the mains, it starts the operation automatically.
After starting the appliance, wait at least 4-6 hours before placing food into the appliance .
The indicator LEDs on the control panel light up for approximately 1 second, and after initialization process, setpoint is displayed.
Note:
- If food is placed in the refrigarator before the appliance has cooled completely, it may deteriorate.
- If fresh food is loaded in freezer position 3 on control panel should be chosen.
FAN WITH A BUTTON
The fan improves temperature distribution inside the refrigerator compartment, allowing better preservation of stored food.
To switch on the fan press the button ( 1a ). It is advisable to activate the fan when the ambient air temperature is over 27 ÷ 28°C or if you perceive drops of water on the glass shelves or in the severe humidity conditions.
Note:
Do not obstruct the air intake area with food items.
The fan will run ONLY when the compressor is in operation.
Remember to turn off the fan when there is a lower ambient air temperature.
If the appliance has the fan it can be equipped with the antibacterial filter.
Remove it from the box (found in the crisper drawer
(item 7 ) and insert into the cover of fan (item 1b ).
The replacement procedure is attached with the filter.
ELECTRONIC CONTROL PANEL
DESCRIPTION
1.
extra low temperature "Fast cooling"
2.
high temperature
3.
medium temperature
4.
low temperature
5.
temperature selection/Fast cooling (3 sec. minimum) pushbutton
D GB F NL E P I GR S N DK FIN PL CZ SK H RUS BG RO
PRODUCT SHEET
OPERATION DESCRIPTION
Temperature adjustment is made with pushbutton (item 5).
Temperature setpoint is done for both compartments at one time – fridge and freezer.
At first plug-in of appliance factory setpoint is chosen – medium position (item 3).
Following table shows set-points level
GB
ABNORMAL APPLIANCE OPERATION
When the product is plugged in to the mains, during first
10 minutes of its performance, possible temperature sensor failure will be displayed according to following table:
Refrigerator evaporator sensor failure
Refrigerator sensor failure
Refrigerator evaporator & refrigerator sensor failure
Description:
LED OFF
LED ON
Description:
LED OFF
LED Flashing
GUIDE TO SELECTING FUNCTIONS
Temperature selection pushbutton (item 5 ) is used to set desired temperature level, from coldest to warmest . At each short pressure of the pushbutton, the setpoint will change (cyclically).
Fast Cooling function
The use of this function is recommended when placing a very high quantity of food in the refrigerator compartment.
By pressing and hold the button (item 5 ) for 3 sec. it is possible to increase the cooling speed of the foods inside the refrigerator compartment. The yellow LED (item 1 ) will come on. The function is automatically deactivated after 6 hours.
The "Fast cooling" function can be manually deactivated by pressing and hold the same button (item 5 ) for 3 sec., the yellow LED (item1) is off.
Note:
- Fast Cooling function should be also switched ON before placing fresh food to be frozen in the freezer compartment.
- Fast Cooling function has to be engaged in order to maximize freezing capacity, thus it has to be engaged before to add light load.
The appliance will work preserving the food stored, but it is necessary to contact after-sales service and provide alarm code.
Note: in case of power failure, appliance goes back to normal operation and previously chosen setpoint is restored.
DEFROSTING THE FREEZER
COMPARTMENT
No Frost freezers provide chilled air circulation around the storage areas and prevent the formation of ice, thereby completely eliminating the need for defrosting.
Frozen items don't stick to the walls, labeling stays legible and storage space remains neat and clear.
DEFROSTING THE REFRIGERATOR
COMPARTMENT
Refrigerator compartment defrosting is completely automatic.
Droplets of water on the rear wall inside the refrigerator compartment indicate that the automatic defrost phase is in progress. The defrost water is automatically run into a drain hole and collected in a container, where it evaporates.
REPLACING THE LIGHT BULB
Always disconnect the refrigerator from the power supply before replacing any light bulb.
If the inside light is not working, it is necessary to:
1.
Remove the light cover: move it upwards as shown in figure.
2.
Check the bulb. If necessary unscrew the broken bulb and replace it with the new one.
3.
Put on the light cover.
Do not leave the bulb uncovered.
D GB F NL E P I GR S N DK FIN PL CZ SK H RUS BG RO
